SECTION EPOXY RESIN FLOORING

Size: px
Start display at page:

Download "SECTION EPOXY RESIN FLOORING"

Transcription

1 SECTION EPOXY RESIN FLOORING PART 1 - GENERAL 1.1 SECTION INCLUDES A. Furnish all necessary material, labor and equipment required to prepare designated traffic areas and install quartz broadcast epoxy resin flooring. 1.2 RELATED SECTIONS A. Vinyl composition tile. B. Recessed plumbing access cover frames. C. Remove and reset existing floor drains as required to complete the work. 1.3 REFERENCES A. ASTM C722 - Chemical-resistant resin monolithic surfacing. B. ASTM C811 - Surface preparation of concrete for application of chemical-resistant resin monolithic surfacings. C. ASTM D570 - Water absorption of plastics. D. ASTM D638 - Tensile properties of plastics. E. ASTM D695 - Compressive properties of rigid plastics. F. ASTM D905 - Strength properties of adhesive bonds in shear by compression loading. G. ASTM D Resistance of transparent plastic materials to abrasion. H. ASTM D Fire retardancy of paints (cabinet method). I. ASTM E96 - Water vapor transmission of materials SUBMITTALS A. Product data: Provide manufacturers specifications and data on specified products, describing physical and performance characteristics; sizes, patterns and colors available. B. Samples: Submit two samples, 6 x 6 inch in size illustrating color, patter and surface texture for each floor material for each color specified. C. Manufacturer's installation instructions: Indicate special procedures and perimeter conditions requiring special attention. D. Maintenance data: Include maintenance procedures, recommended maintenance materials, procedures for stain removal, repairing surface, and suggested schedule for cleaning. EPOXY RESIN FLOORING

2 1.5 QUALIFICATIONS A. Manufacturer: Company specializing in manufacturing the products specified in this section with minimum five years experience. B. Applicator: Company specializing in performing the work of the section with minimum five years experience approved by manufacturer. The applicator shall submit a list of three projects using either the specified material or another material pre-approved for this project that they have installed in the last five years. Information shall include: Project name, square footage, contact name with Owner address and phone number. C. Supervisor: Trained by product manufacturer. 1.6 DELIVERY, STORAGE AND HANDLING A. Storage resin materials in a dry, secure area. B. Maintain minimum temperature of 55 degrees F. C. Store materials in accordance with manufacturer's instructions with seals and labels intact and legible. Maintain temperatures within the required range. 1.7 ENVIRONMENTAL REQUIREMENTS A. Maintain ambient temperature required by manufacturer three days prior to, during, and 24 hours after installation of materials. 1.8 WARRANTY A. Provide three year warranty. B. Warranty: Include coverage against flooring delamination from substrate and/or degradation of surface finish. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. General Polymers: Product: Ceramic carpet or approved equal. B. Key Resin Company: Product: Key Quartz B MATERIALS A. System primer: General polymers #3501 Epoxy damp primer or approved equal. Spread rate: square feet per gallon. B. Base Coat: General polymers #3561 Epoxy Resin Glaze and General Polymers #5700F Ceramic Fired Quartz granules. Glaze spread rate: 140 square feet per gallon. Granule application: 3-4 pounds per 10 square feet. EPOXY RESIN FLOORING

3 C. Second coat: General polymers #3561 Epoxy Resin Glaze and General Polymers #5700F Ceramic Fired Quartz granules. Glaze spread rate: square feet per gallon. Granule application: 3-4 pounds per 10 square feet. D. Grouting: Sealing material first coat: General polymers #3644 Chemical Resistant Epoxy Coat. Spread Rate: 100 square feet per gallon (high profile for skid inhibition). E. Grouting: Sealing material second coat: General polymers #3644 Chemical Resistant Epoxy Coat. Spread Rate: square feet per gallon. F. Flooring: Conform to the following: 2.3 ACCESSORIES A. Base Caps: Manufacturer's standard. B. Subfloor Filler: Type as recommended by flooring material manufacturer. 2.4 COLORS A. Matrix and quartz granules: color as selected from manufacturer's standard. PART 3 - EXECUTION 3.1 EXAMINATION A. Verify that surfaces are smooth and flat with maximum variation of 1/4 inch in 10 ft, and are ready to receive work. B. Verify floor and lower wall surfaces are free of substances that may impair adhesion of new adhesive and finish materials. 3.2 PREPARATION A. Remove sub-floor ridges and bumps. Fill low spots, cracks, joints, holes, and other defects with sub-floor filler. B. Apply, trowel, and float filler to achieve smooth, flat, hard surface, grind irregularities above the surface level. Prohibit traffic until filler is cured. C. Vacuum clean substrate. Any oil or grease not removed by grit blasting must be chemically removed. D. Apply primer to surfaces as recommended by manufacturer. 3.3 INSTALLATION - TERMINATING BASE CAP STRIP A. Install terminating cap strip at top of base; attach securely to wall substrate. EPOXY RESIN FLOORING

4 3.4 INSTALLATION - FLOORING A. Apply in compliance with manufacturer's instructions and strictly adhere to mixing and application methods, recoat windows, cure times and environmental restrictions. Integral quartz cove base shall be installed at all locations where manufacturer's terminating cap strip. B. The flooring shall terminate at the edge of all expansion joints. The floor installer shall install the expansion joint cover in accordance with manufacturer's instructions. Top of flooring material and top of expansion joint cover shall be flush. Chase floor as required for installation of expansion joint cover. C. All areas where the install floor does not abut against a vertical surface, prefabricated expansion joint cover or terrazzo dividing strip shall be chased. The chase shall be 1 1/2" wide to a straight, saw-cut 1/2" depth. D. Apply to a minimum thickness of 1/8 inch. E. Finish to smooth level surface. 3.5 PROTECTION OF FINISHED WORK A. Protect finished work. Cure in compliance with manufacturer's directions. B. Prohibit traffic on floor finish for 48 hours after installation. C. Barricade area to protect flooring until cured and until final inspection. D. Clean floor just prior to final inspection, using material and procedures suitable to the system manufacturer. END OF SECTION EPOXY RESIN FLOORING

5 SECTION SPECIAL COATINGS PART 1 - GENERAL 1.1 WORK INCLUDED A. Finish coating of interior wall areas scheduled to receive epoxy coatings. B. Finish for exterior painted steel and scheduled field painted aluminum items. 1.2 REFERENCES A. ANSI/ASTM D16 - Definitions of Terms Relating to Paint, Varnish, Lacquer, and Related Products. B. ASTM D Test Method for Moisture Content of Wood. 1.3 DEFINITIONS A. Conform to ANSI/ASTM D16 for interpretation of terms used in this Section. 1.4 QUALITY ASSURANCE A. Product Manufacturer: Company specializing in manufacturing quality paint and finish products with three years experience. B. Applicator: Company specializing in commercial painting and finishing with 3 years experience. 1.5 REGULATORY REQUIREMENTS A. Conform to the 2003 edition of the International Building Code for flame/fuel/smoke rating requirements for finishes. 1.6 SUBMITTALS A. Submit product data under provisions of Section B. Submit samples under provisions of Section FIELD SAMPLES A. Provide samples under provisions of Section B. Provide field sample panel, 12 inches long by 24 inches wide, illustrating each texture and finish. C. Locate where directed. D. Accepted sample may remain as part of the Work. SPECIAL COATINGS

6 1.8 DELIVERY, STORAGE, AND HANDLING A. Deliver products to site under provisions of Section B. Store and protect products under provisions of Section C. Deliver products to site in sealed and labeled containers; inspect to verify acceptance. D. Container labeling to include manufacturer's name, type of paint, brand name, brand code, coverage, surface preparation, drying time, cleanup, color designation, and instructions for mixing and reducing. E. Store paint materials at minimum ambient temperature of 45 degrees F (7 degrees C) and a maximum of 90 degrees F (32 degrees C), in well ventilated area, unless required otherwise by manufacturer's instructions. F. Take precautionary measures to prevent fire hazards and spontaneous combustion. 1.9 ENVIRONMENTAL REQUIREMENTS A. Provide continuous ventilation for 24 hours before, during, and 48 hours after application of finishes, unless required otherwise by manufacturer's instructions. B. Provide lighting level of 80 ft candles measured mid-height at substrate surface EXTRA STOCK A. Provide a one gallon container of each color to Owner. Total not to exceed 5 gallons. B. Label each container with color, texture, in addition to the manufacturer's label. PART 2 - PRODUCTS 2.1 ACCEPTABLE MANUFACTURERS A. Tnemec/ICI/Sherwin Williams for cementitious block filler epoxy and alkyd coatings. 2.2 MATERIALS A. Coatings: Ready mixed, except field catalyzed coatings. Process pigments to a soft paste consistency, capable of being readily and uniformly dispersed to a homogeneous coating. B. Coatings: Good flow and brushing properties; capable of drying or curing free of streaks or sags. C. Accessory Materials: Linseed oil, shellac, turpentine, paint thinners and other materials not specifically indicated but required to achieve the finishes specified, of commercial quality. SPECIAL COATINGS

7 2.3 FINISHES A. Refer to schedule at end of Section for surface finish schedule. PART 3 - EXECUTION 3.1 INSPECTION A. Verify that surfaces are ready to receive work as instructed by the product manufacturer. B. Examine surfaces scheduled to be finished prior to commencement of work. Report any condition that may potentially affect proper application. C. Measure moisture content of surfaces using an electronic moisture meter. Do not apply finishes unless moisture content of surfaces are below the following maximums: 1. Plaster and Gypsum Wallboard: 12 percent. 2. Masonry, Concrete, and Concrete Unit Masonry: 12 percent. 3. Interior Located Wood: 15 percent, measured in accordance with ASTM D2016. D. Beginning of installation means acceptance of existing substrate. 3.2 PREPARATION A. Remove electrical plates, hardware, light fixture trim, and fittings prior to preparing surfaces or finishing. B. Correct minor defects and clean surfaces which affect work of this Section. C. Shellac and seal marks which may bleed through surface finishes. D. Impervious Surfaces: Remove mildew by scrubbing with solution of tri-sodium phosphate and bleach. Rinse with clean water and allow to dry. E. Aluminum Surfaces Scheduled for Paint Finish: Remove surface contamination by steam or high pressure water. Remove oxidation with acid etch and solvent washing. Apply etching primer immediately following cleaning. F. Asphalt, Creosote, or Bituminous Surfaces Scheduled for Paint Finish: Remove foreign particles to permit adhesive of finishing materials. Apply compatible sealer or primer. G. Insulated Coverings: Remove dirt, grease, and oil from canvas and cotton. H. Concrete Floors: See Division 3. I. Gypsum Board Surfaces: Latex fill minor defects. Spot prime defects after repair. SPECIAL COATINGS

8 J. Galvanized Surfaces: Remove surface contamination and oils and wash with solvent. Apply coat of etching primer. K. Concrete and Unit Masonry Surfaces Scheduled to Receive Paint Finish: Remove dirt, loose mortar, scale, salt or alkali powder, and other foreign matter. Remove oil and grease with a solution of trisodium phosphate; rinse well and allow to dry. Remove stains caused by weathering of corroding metals with a solution of sodium metasilicate after thoroughly wetting with water. Allow to dry. L. Plaster Surfaces: Fill hairline cracks, small holes, and imperfections with latex patching plaster. Make smooth and flush with adjacent surfaces. Wash and neutralize high alkali surfaces. M. Uncoated Steel and Iron Surfaces: Remove grease, scale, dirt, and rust. Where heavy coatings of scale are evident, remove by wire brushing or sandblasting; clean by washing with solvent. Apply a treatment of phosphoric acid solution, ensuring weld joints, bolts, and nuts are similarly cleaned. Spot prime paint after repairs. N. Shop Primed Steel Surfaces: Sand and scrape to remove loose primer and rust. Feather edges to make touch-up patches inconspicuous. Clean surfaces with solvent. Prime bare steel surfaces. Prime metal items including shop primed items. O. Interior Wood Items Scheduled to Receive Finish: Wipe off dust and grit prior to priming. Seal knots, pitch streaks, and sappy sections with sealer. Fill nail holes and cracks after primer has dried; sand between coats. P. Wood and Metal Doors Scheduled for Painting: Seal top and bottom edges with primer. 3.3 PROTECTION A. Protect elements surrounding the work of this Section from damage or disfiguration. B. Repair damage to other surfaces caused by work of this Section. C. Furnish drop cloths, shields, and protective methods to prevent spray or droppings from disfiguring other surfaces. D. Remove empty paint containers from site. 3.4 APPLICATION A. Apply products in accordance with manufacturer's instructions. B. Do not apply finishes to surfaces that are not dry. C. Apply each coat to uniform finish. D. Apply each coat of paint slightly darker than preceding coat unless otherwise approved. SPECIAL COATINGS

9 E. Sand lightly between coats to achieve required finish. F. Allow applied coat to dry before next coat is applied. G. Where clear finishes are required, tint fillers to match wood. Work fillers into the grain before set. Wipe excess from surface. H. Prime back surfaces of interior and exterior woodwork with primer paint. I. Prime back surfaces of interior woodwork scheduled to receive stain or varnish finish with gloss varnish reduced 25 percent with mineral spirits. 3.5 FINISHING MECHANICAL AND ELECTRICAL EQUIPMENT A. Paint shop primed equipment. Paint all wall mounted electrical equipment to match new masonry walls. B. Remove unfinished louvers, grilles, covers, and access panels on mechanical and electrical components and paint separately. C. Prime and paint insulated and exposed pipes, conduit boxes, insulated and exposed ducts, hangers, brackets, collars and supports, except where items are pre-finished. D. Replace identification markings on mechanical or electrical equipment when painted accidentally. E. Paint interior surfaces of air ducts, and convector and baseboard heating cabinets that are visible through grilles and louvers with one coat or flat black paint, to limit of sight line. Paint dampers exposed behind louvers, grilles, and convector and baseboard cabinets to match face panels. F. Paint exposed conduit and electrical equipment occurring at finished areas. G. Paint both sides and edges of plywood backboards for electrical and telephone equipment before installing equipment. H. Replace electrical plates, hardware, light fixture trim, and fittings removed prior to finishing. 3.6 CLEANING A. As Work proceeds, promptly remove paint where spilled, splashed, or splattered. B. During progress of Work maintain premises free of unnecessary accumulation of tools, equipment, surplus materials, and debris. C. Collect cotton waste, cloths, and materials which may constitute a fire hazard, place in closed metal containers and remove daily from site. 3.7 SCHEDULE - INTERIOR SURFACES SPECIAL COATINGS

10 A. Concrete and Concrete Block to receive epoxy coating. 1. Surface Preparation: Allow mortar to cure for 28 days. Level protrusions and mortar spatter. All surfaces must be dry, clean and free of all contaminants. All block filler to be rubber squeegee applied at all CMU. Primer: B42W00400 Kem Cati-Coat HS Epoxy Filler Sealer Off White First Coat: B58E Macropoxy 646 Fast Cure Epoxy Part A Mill White Second Coat: B58W Macropoxy 646 Fast Cure Epoxy Part A Mill White 3.8 PAINTING SCHEDULE - EXTERIOR SURFACES A. Galvanized Steel: 1. Surface Preparation: Solvent cleaning per SSPC-SP1 to remove soluble contaminants. Remove insoluble contaminants (rust, white rust, etc.). Power Tool Cleaning per SP3 or by Brush-Off Cleaning per SSPC-SP7. Provide uniform abraded surface profile. 2. Coating System: Primer: ICI 4160 Primer 1st Coat: ICI 2516-XXX Ultra-Hide Duras Exterior Alkyd Semi-Gloss Enamel 2nd Coat: ICI 2516-XXX Ultra-Hide Duras Exterior Alkyd Semi-Gloss Enamel TOTAL SYSTEM THICKNESS: mils B. Steel - Shop Primed: 1. Touch up with original primer per Division All surfaces must be dry, clean and free of all contaminants. 2. Coating System: 1st Coat: ICI 2516-XXX Ultra-Hide Duras Exterior Alkyd Semi-Gloss Enamel 2nd Cost: ICI 2516-XXX Ultra-Hide Duras Exterior Alkyd Semi-Gloss Enamel B. Cement Siding Primer: B42WJ0050 Southwest Builders Summit Exterior Acrylic Primer White First Coat: B13WJ0051 Southwest Builders Summit Exterior Latex Satin Extra White Second Coat: B13WJ0051 Southwest Builders Summit Exterior Latex Satin Extra White END OF SECTION SPECIAL COATINGS

11 SECTION PAINTING PART 1 - GENERAL 1.1 WORK INCLUDED A. Surface preparation. B. Surface finish schedule. 1.2 REFERENCES A. ANSI/ASTM D16 - Definitions of Terms Relating to Paint, Varnish, Lacquer, and Related Products. B. ASTM D Test Method for Moisture Content of Wood. 1.3 DEFINITIONS A. Conform to ANSI/ASTM D16 for interpretation of terms used in this Section. 1.4 QUALITY ASSURANCE A. Product Manufacturer: Company specializing in manufacturing quality paint and finish products with three years experience. B. Applicator: Company specializing in commercial painting and finishing with 3 years experience. 1.5 REGULATORY REQUIREMENTS A. Conform to the 2003 edition of the International Building Code for flame/fuel/smoke rating requirements for finishes. 1.6 SUBMITTALS A. Submit product data under provisions of Section B. Submit samples under provisions of Section FIELD SAMPLES A. Provide samples under provisions of Section B. Provide field sample panel, 12 inches long by 24 inches wide, illustrating each texture and finish. C. Locate where directed. D. Accepted sample may remain as part of the Work. PAINTING

12 1.8 DELIVERY, STORAGE, AND HANDLING A. Deliver products to site under provisions of Section B. Store and protect products under provisions of Section C. Deliver products to site in sealed and labelled containers; inspect to verify acceptance. D. Container labelling to include manufacturer's name, type of paint, brand name, brand code, coverage, surface preparation, drying time, cleanup, color designation, and instructions for mixing and reducing. E. Store paint materials at minimum ambient temperature of 45 degrees F (7 degrees C) and a maximum of 90 degrees F (32 degrees C), in well ventilated area, unless required otherwise by manufacturer's instructions. F. Take precautionary measures to prevent fire hazards and spontaneous combustion. 1.9 ENVIRONMENTAL REQUIREMENTS A. Provide continuous ventilation for 24 hours before, during, and 48 hours after application of finishes, unless required otherwise by manufacturer's instructions. B. Provide lighting level of 80 ft candles measured mid-height at substrate surface EXTRA STOCK A. Provide a one gallon container of each color to Owner. Total not to exceed 5 gallons. B. Label each container with color, texture, in addition to the manufacturer's label. PART 2 - PRODUCTS 2.1 ACCEPTABLE MANUFACTURERS A. Sherwin Williams. B. I.C.I. C. Substitutions: Under provisions of Section MATERIALS A. Coatings: Ready mixed, except field catalyzed coatings. Process pigments to a soft paste consistency, capable of being readily and uniformly dispersed to a homogeneous coating. B. Coatings: Good flow and brushing properties; capable of drying or curing free of streaks or sags. PAINTING

13 C. Accessory Materials: Linseed oil, shellac, turpentine, paint thinners and other materials not specifically indicated but required to achieve the finishes specified, of commercial quality. 2.3 FINISHES A. Refer to schedule at end of Section for surface finish schedule. PART 3 - EXECUTION 3.1 INSPECTION A. Verify that surfaces are ready to receive work as instructed by the product manufacturer. B. Examine surfaces scheduled to be finished prior to commencement of work. Report any condition that may potentially affect proper application. C. Measure moisture content of surfaces using an electronic moisture meter. Do not apply finishes unless moisture content of surfaces are below the following maximums: 1. Plaster and Gypsum Wallboard: 12 percent. 2. Masonry, Concrete, and Concrete Unit Masonry: 12 percent. 3. Interior Located Wood: 15 percent, measured in accordance with ASTM D2016. D. Beginning of installation means acceptance of existing substrate. 3.2 PREPARATION A. Remove electrical plates, hardware, light fixture trim, and fittings prior to preparing surfaces or finishing. B. Correct minor defects and clean surfaces which affect work of this Section. C. Shellac and seal marks which may bleed through surface finishes. D. Impervious Surfaces: Remove mildew by scrubbing with solution of tri-sodium phosphate and bleach. Rinse with clean water and allow to dry. E. Aluminum Surfaces Scheduled for Paint Finish: Remove surface contamination by steam or high pressure water. Remove oxidation with acid etch and solvent washing. Apply etching primer immediately following cleaning. F. Asphalt, Creosote, or Bituminous Surfaces Scheduled for Paint Finish: Remove foreign particles to permit adhesive of finishing materials. Apply compatible sealer or primer. G. Insulated Coverings: Remove dirt, grease, and oil from canvas and cotton. H. Concrete Floors: See Division 3. I. Gypsum Board Surfaces: Latex fill minor defects. Spot prime defects after repair. PAINTING

14 J. Galvanized Surfaces: Remove surface contamination and oils and wash with solvent. Apply coat of etching primer. K. Concrete and Unit Masonry Surfaces Scheduled to Receive Paint Finish: Remove dirt, loose mortar, scale, salt or alkali powder, and other foreign matter. Remove oil and grease with a solution of trisodium phosphate; rinse well and allow to dry. Remove stains caused by weathering of corroding metals with a solution of sodium metasilicate after thoroughly wetting with water. Allow to dry. L. Plaster Surfaces: Fill hairline cracks, small holes, and imperfections with latex patching plaster. Make smooth and flush with adjacent surfaces. Wash and neutralize high alkali surfaces. M. Uncoated Steel and Iron Surfaces: Remove grease, scale, dirt, and rust. Where heavy coatings of scale are evident, remove by wire brushing or sandblasting; clean by washing with solvent. Apply a treatment of phosphoric acid solution, ensuring weld joints, bolts, and nuts are similarly cleaned. Spot prime paint after repairs. N. Shop Primed Steel Surfaces: Sand and scrape to remove loose primer and rust. Feather edges to make touch-up patches inconspicuous. Clean surfaces with solvent. Prime bare steel surfaces. Prime metal items including shop primed items. O. Interior Wood Items Scheduled to Receive Finish: Wipe off dust and grit prior to priming. Seal knots, pitch streaks, and sappy sections with sealer. Fill nail holes and cracks after primer has dried; sand between coats. P. Wood and Metal Doors Scheduled for Painting: Seal top and bottom edges with primer. 3.3 PROTECTION A. Protect elements surrounding the work of this Section from damage or disfiguration. B. Repair damage to other surfaces caused by work of this Section. C. Furnish drop cloths, shields, and protective methods to prevent spray or droppings from disfiguring other surfaces. D. Remove empty paint containers from site. 3.4 APPLICATION A. Apply products in accordance with manufacturer's instructions. B. Do not apply finishes to surfaces that are not dry. C. Apply each coat to uniform finish. D. Apply each coat of paint slightly darker than preceding coat unless otherwise approved. E. Sand lightly between coats to achieve required finish. PAINTING

15 F. Allow applied coat to dry before next coat is applied. G. Where clear finishes are required, tint fillers to match wood. Work fillers into the grain before set. Wipe excess from surface. H. Prime back surfaces of interior and exterior woodwork with primer paint. I. Prime back surfaces of interior woodwork scheduled to receive stain or varnish finish with gloss varnish reduced 25 percent with mineral spirits. 3.5 FINISHING MECHANICAL AND ELECTRICAL EQUIPMENT A. Paint shop primed equipment and all roof top mounted equipment. B. Remove unfinished louvers, grilles, covers, and access panels on mechanical and electrical components and paint separately. C. Prime and paint insulated and exposed pipes, conduit boxes, insulated and exposed ducts, hangers, brackets, collars and supports, except where items are prefinished. D. Replace identification markings on mechanical or electrical equipment when painted accidentally. E. Paint interior surfaces of air ducts, and convector and baseboard heating cabinets that are visible through grilles and louvers with one coat or flat black paint, to limit of sight line. Paint dampers exposed behind louvers, grilles, and convector and baseboard cabinets to match face panels. F. Paint exposed conduit and electrical equipment occurring at finished areas. G. Paint both sides and edges of plywood backboards for electrical and telephone equipment before installing equipment. H. Replace electrical plates, hardware, light fixture trim, and fittings removed prior to finishing. 3.6 CLEANING A. As Work proceeds, promptly remove paint where spilled, splashed, or splattered. B. During progress of Work maintain premises free of unnecessary accumulation of tools, equipment, surplus materials, and debris. C. Collect cotton waste, cloths, and materials which may constitute a fire hazard, place in closed metal containers and remove daily from site. 3.7 SCHEDULE - INTERIOR SURFACES A. Wood - Painted 1. One coat Alkyd Primer Sealer. SW Pro Mar undercoater B49 W200; 2.0 mils DFT. 2. Two coats Alkyd Enamel, Eggshell, SW Pro Mar B33; 2.0 mils DFT per coat. PAINTING

16 B. Wood - Transparent Finish 1. Filler coat. 2. One coat stain. 3. One coat sealer. 4. Two coats stain finish varnish. 5. Materials to be selected from submitted samples. C. Concrete, Concrete Block 1. One coat block filler: S.W. Loxon block filler. 2. Two coats Semi-Gloss Enamel. SW Pro Mar 200 B31 W200; 2.0 mils DFT. D. Concrete and Concrete Block (epoxy finish) 1. See Section Special Coatings E. Steel - Unprimed 1. One coat zinc chromate primer. 2. Two coats Alkyd Enamel satin finish. SW Pro Mar B34; 2.0 mils DFT per coat. F. Steel - Shop Primed 1. Touch up with original primer. All surfaces must be dry, clean and free of contaminants. 2. Two coats Alkyd Enamel satin finish, SW Pro Mar B34; 2.0 mils DFT per coat. G. Steel Galvanized Metal Primer: B66W00310 Pro Industrial Pro-Cryl Universal Primer Off White First Coat: B54W00151 Industrial Urethane Alkyd Enamel Extra White Second Coat: B54W00151 Industrial Urethane Alkyd Enamel Extra White H. Cement Siding Primer: B42WJ0050 Southwest Builders Summit Exterior Acrylic Primer White First Coat: B13WJ0051 Southwest Builders Summit Exterior Latex Satin Extra White Second Coat: B13WJ0051 Southwest Builders Summit Exterior Latex Satin Extra White 3.8 SCHEDULE - EXTERIOR SURFACES A. See Section END OF SECTION PAINTING

SECTION PAINTING. A. Surface preparation and field application of paints and coatings at interior and exterior surfaces.

SECTION PAINTING. A. Surface preparation and field application of paints and coatings at interior and exterior surfaces. SECTION 09910 PAINTING 1 PART ONE - GENERAL 1.1 COORDINATION A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification Sections apply

More information

SECTION PAINTS AND COATINGS. 1.3 REFERENCES A. ASTM D 16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications; 2000.

SECTION PAINTS AND COATINGS. 1.3 REFERENCES A. ASTM D 16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications; 2000. PART 1 - GENERAL 1.1 SECTION INCLUDES A. Surface preparation. B. Field application of paints, stains, varnishes, and other coatings. C. See Schedule - Surfaces to be Finished, at end of Section. 1.2 RELATED

More information

SECTION CERAMIC TILE

SECTION CERAMIC TILE SECTION 09310 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

SECTION PAINTS AND COATINGS

SECTION PAINTS AND COATINGS McClellan Blakemore Architects New Warehouse Facility for SECTION 09900 PAINTS AND COATINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints and stains. C. Scope:

More information

ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019

ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019 ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # 275-18 ADDENDUM NO. 3 April 02, 2019 This Addendum No. 3 ( Addendum ) is dated the date set forth above and modifies certain Bidding Documents issued

More information

A. Section includes surface preparation and the application of paint systems on interior substrates.

A. Section includes surface preparation and the application of paint systems on interior substrates. SECTION 09 91 23 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 099600 - HIGH PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.

1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials

More information

SECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)

SECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) - 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane

More information

A. Section includes surface preparation and application of wood finishes[.]

A. Section includes surface preparation and application of wood finishes[.] SECTION 09 93 00 - STAINING AND TRANSPARENT FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

The City of Winnipeg NEWPCC Lab Renovation

The City of Winnipeg NEWPCC Lab Renovation Bid Opportunity 253-2011 Page 1 of 6 Part 1 General 1.1 SUMMARY.1 Work under this contract includes, but is not necessarily limited to:.1 Surface preparation of substrates as required for acceptance of

More information

SECTION PAINTING Ultra Premium

SECTION PAINTING Ultra Premium SECTION 09 90 00 PAINTING Ultra Premium PART 3-EXECUTION 3.01 PREPARATION: A. Perform preparation and cleaning procedures in strict accordance with coating manufacturer s instructions for each substrate

More information

MDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls

MDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing

More information

1/16 Single Broadcast Polymer Flooring System

1/16 Single Broadcast Polymer Flooring System specification 1/16 Single Broadcast Polymer Flooring System Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions

More information

A. Section includes surface preparation and the application of high-performance coating systems on the following substrates:

A. Section includes surface preparation and the application of high-performance coating systems on the following substrates: ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY

More information

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish. SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION RESILIENT TILE FLOORING. A. Section includes vinyl composition floor tile and accessories indicated and as specified.

SECTION RESILIENT TILE FLOORING. A. Section includes vinyl composition floor tile and accessories indicated and as specified. SECTION 09 65 19 RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 SUMMARY A. Section includes vinyl composition floor tile and accessories indicated and as specified. 1.2 SUBMITTALS A. Product Data: Submit

More information

Olde Hickory 1, 2 & Hickory Hill Court Fort Myers, Fl Revised June 10, 2015

Olde Hickory 1, 2 & Hickory Hill Court Fort Myers, Fl Revised June 10, 2015 Prepared For: Tony Roller P and M Property Management 14360 South Tamiami Trail # B Fort Myers Fl. 33912 Fort Myers (239) 481-1577 / Naples (239) 596-7887 Fax # (239) 481-1789 Tony Roller

More information

SECTION RESILIENT SHEET FLOORING

SECTION RESILIENT SHEET FLOORING SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.

More information

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING

More information

SECTION RESILIENT SHEET FLOORING

SECTION RESILIENT SHEET FLOORING SECTION 09665 RESILIENT SHEET FLOORING PART 1 - GENERAL 1.1 DESCRIPTION A. This Section specifies the installation of sheet flooring with backing and integral cove base. 1.2 RELATED WORK A. Color and pattern:

More information

SECTION EPOXY FLOORING SYSTEMS

SECTION EPOXY FLOORING SYSTEMS SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Rust-Oleum Industrial Brands Specification

Rust-Oleum Industrial Brands Specification Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 44 A solvent based coating system High Performance 7400 System 450 VOC DTM Alkyd Enamel

More information

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,

More information

SECTION POLYPROPYLENE FABRIC WALL COVERING

SECTION POLYPROPYLENE FABRIC WALL COVERING PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 31 POLYPROPYLENE FABRIC WALL COVERING SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph not

More information

Project: Amity Plaza Project No.: Amity Plaza Community Room

Project: Amity Plaza Project No.: Amity Plaza Community Room D a t e: September 9, 2013 Addendum No: 02 Project: Amity Plaza Project No.: Amity Plaza Community Room Owner: Architect: ej architecture, pllc 5745 South Bannock Street 575 Union Boulevard Littleton,

More information

SECTION RESILIENT TILE FLOORING

SECTION RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 65 19 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

Acrylitex Interior Texture and Coating Submittal Documentation

Acrylitex Interior Texture and Coating Submittal Documentation Acrylitex Interior Texture and Coating Submittal Documentation Project: Contractor: Installer: Supplier: John Wagner & Associates dba Grabber Construction Products 866-237-GRAB(4722) Distributor: Acrylic

More information

Copyright 2018, The Sherwin-Williams Company ISSUED MAY OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS

Copyright 2018, The Sherwin-Williams Company ISSUED MAY OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE

More information

SECTION GYPSUM BOARD ASSEMBLIES

SECTION GYPSUM BOARD ASSEMBLIES SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for

More information

SECTION RESINOUS FLOORING

SECTION RESINOUS FLOORING SECTION 09705 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section includes all materials and installation necessary to provide resinous flooring system with integral cove base and top finish

More information

Orangeburg County Sheriff s Department: Storage & K-9 Facility

Orangeburg County Sheriff s Department: Storage & K-9 Facility SECTION 09900-1 INTERIOR, EXTERIOR AND INDUSTRIAL PAINTS AND COATINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior paint and coatings systems (LEED-09 NC/CI/CS Compliant) including surface preparation.

More information

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART 1 - GENERAL 1.01 SECTION INCLUDES A. Concrete Steps B. Handrails C. Safety Rail 1.02 DESCRIPTION OF WORK A. Construction of concrete steps. B. Furnishing

More information

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box

More information

Copyright 2018, The Sherwin-Williams Company ISSUED MAY SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING

Copyright 2018, The Sherwin-Williams Company ISSUED MAY SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 - SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting

More information

ARCHITECTURAL GUIDE SPECIFICATIONS

ARCHITECTURAL GUIDE SPECIFICATIONS ARCHITECTURAL GUIDE SPECIFICATIONS MANNINGTON COLORSCAPE, COLORSPEC, & ONE-STEP STAIR TREADS Section 09 65 13.23 Resilient Stair Treads [Thermoset Rubber Type TS] Created November, 2008 Mannington Mills,

More information

ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment

ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general

More information

TILE TILE

TILE TILE 09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements

More information

For residential housing projects the use of reinforced gypsum wallboards is required in all public and common areas.

For residential housing projects the use of reinforced gypsum wallboards is required in all public and common areas. SECTION 09 00 00 FINISHES DESIGN AND CONSTRUCTION STANDARDS SPECIFICATION GUIDELINES 09 00 00 SECTION 09 20 00 - PLASTER AND GYPSUM BOARD Use 5/8 gypsum wallboard for walls and ceilings. For residential

More information

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 09 - FINISHES

MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 09 - FINISHES SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Concrete. 2. Concrete

More information

INDUSTRIAL PAINTING SCHEDULE GUIDE

INDUSTRIAL PAINTING SCHEDULE GUIDE Copyright 2014, The Sherwin-Williams Company ISSUED May 2014 09 96 00- INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting

More information

SECTION RESILIENT FLOORING

SECTION RESILIENT FLOORING PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 65 00 RESILIENT FLOORING A. Resilient sheet and tile flooring B. Resilient base C. Resilient stair nosing, treads, risers and skirting 1.2 REFERENCES A. ASTM

More information

ROCKGRIP UNIVERSAL ACRYLIC PVA

ROCKGRIP UNIVERSAL ACRYLIC PVA TECHNICAL DATA SHEET Version 1 2016 FEBRUARY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Matt finish for interior use PRODUCT USES Suitable for use on primed new or previously painted

More information

Education Facility Guide Specification

Education Facility Guide Specification Education Facility Guide Specification This Painting Schedule is furnished as a guide to select paint systems, and is not all-inclusive of available Sherwin-Williams products. Specifiers should review

More information

1/4 Industrial Trowel System

1/4 Industrial Trowel System System Specification 1/4 Industrial Trowel System Revision Date: 6/2015 Printed Date: 6/2015 PART 1 GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of contract including General and Special

More information

Rust-Oleum Industrial Brands Specification

Rust-Oleum Industrial Brands Specification Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 2 A solvent based coating system High Performance 9100/9800 System DTM Epoxy Mastic/DTM

More information

SECTION (09941) - TEXTURED FINISHING

SECTION (09941) - TEXTURED FINISHING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: SECTION 09 94 13 (09941) - TEXTURED FINISHING 1. Spray Applied Textured Finish and Primer a. Textured Finish for Ceilings. b. Textured Finish for Walls.

More information

SECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.

SECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate. Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call

More information

.1 Suspension System Framing and Furring for Gypsum Board Assemblies..2 Wire hangers, fasteners, main runners & cross tees.

.1 Suspension System Framing and Furring for Gypsum Board Assemblies..2 Wire hangers, fasteners, main runners & cross tees. Metal Suspension System Section 09120 Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Suspension System Framing and Furring for Gypsum Board Assemblies..2 Wire hangers, fasteners, main runners & cross tees.

More information

SECTION PORTLAND CEMENT TERRAZZO FLOORING

SECTION PORTLAND CEMENT TERRAZZO FLOORING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 66 13 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between //---// if not applicable to project. Also delete any other item or paragraph

More information

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL

CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES

More information

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3

More information

DAYTONA BEACH PIER BUILDING RESTORATION 06/10

DAYTONA BEACH PIER BUILDING RESTORATION 06/10 SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Steel. 2. Galvanized

More information

SECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES

SECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 05 16 SUBSURFACE PREPARATION FOR FLOOR FINISHES SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph

More information

Specifications. Specifications (Architectual) Metallic System. Metallic System

Specifications. Specifications (Architectual) Metallic System. Metallic System (Architectual) Metallic System Architectual NeverStrip Floor Coatings, 6-15 Mils Master Format Section 096700 Fluid Applied Flooring 1 of 6 NeverStrip Metallic High-Build Decorative Epoxy/Urethane Coating

More information

SURFACE PREPARATION INSTRUCTIONS: CONCRETE

SURFACE PREPARATION INSTRUCTIONS: CONCRETE SURFACE PREPARATION INSTRUCTIONS: CONCRETE DEFINITION OF TERMS The terms listed will be used frequently throughout this article and listed in boldface for ease of reference. They describe, in detail, the

More information

SECTION RESINOUS FLOORING

SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 67 23 1. Use this section only for NCA projects. 2. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the

More information

White, a range of ready-mixed colours, and colours from the Dulux Colour System

White, a range of ready-mixed colours, and colours from the Dulux Colour System TECHNICAL DATA SHEET Version 2 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior matt finish PRODUCT USES Recommended for exterior and

More information

ITEM 447 PAINTING AND PROTECTIVE COATING

ITEM 447 PAINTING AND PROTECTIVE COATING ITEM 447 FOR PROJECTS INITIATED AFTER NOVEMBER 1, 2008 PAINTING AND PROTECTIVE COATING 447.1 Description. This item shall govern for the finished paints, their source and for the application of paint to

More information

POLYACRYLATE MODIFIED THINSET TERRAZZO 1

POLYACRYLATE MODIFIED THINSET TERRAZZO 1 PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove

More information

DESIGN GUIDELINES AND TECHNICAL STANDARDS

DESIGN GUIDELINES AND TECHNICAL STANDARDS DESIGN GUIDELINES AND TECHNICAL STANDARDS Date of Issuance: January 1, 2014 DIVISION 9 FINISHES SECTION 09 2900 GYPSUM BOARD 1. General: This section outlines the requirements for gypsum board systems.

More information

VengerElectrostatic Coatings Master Specification Page 1

VengerElectrostatic Coatings Master Specification Page 1 Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits

More information

Rust-Oleum Industrial Brands Specification

Rust-Oleum Industrial Brands Specification Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 3 A solvent based coating system High Performance 9300/9800 System Extended Recoat Epoxy

More information

B. Store products in dry spaces protected from the weather, with ambient temperatures maintained between 50 and 90 deg F (10 and 32 deg C).

B. Store products in dry spaces protected from the weather, with ambient temperatures maintained between 50 and 90 deg F (10 and 32 deg C). SECTION 09651 - RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015

SECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 Specification Provided To: Date: Job: PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 96 60 HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 A. Paints and coatings of the following

More information

ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment

ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing

More information

SECTION VINYL-COATED FABRIC WALL COVERINGS

SECTION VINYL-COATED FABRIC WALL COVERINGS PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 72 16 VINYL-COATED FABRIC WALL COVERINGS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

SECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM

SECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM SECTION 096723 RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. This section includes the following: 1. Seamless epoxy flooring system, 1/16 th, 3/32

More information

SECTION RESILIENT BASE AND ACCESSORIES

SECTION RESILIENT BASE AND ACCESSORIES SECTION 09 65 13 RESILIENT BASE AND ACCESSORIES SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes:

More information

Broadcast Parking Garage System

Broadcast Parking Garage System AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete

More information

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,

More information

SECTION EPOXY RESIN FLOORING

SECTION EPOXY RESIN FLOORING SECTION 096723 EPOXY RESIN FLOORING PART 1 GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Concrete Rehabilitation: Section 030131 B. Joint Sealants: Section 079200. 1.02 SYSTEM DESCRIPTION A. The work

More information

SECTION Arisfor WallGuard

SECTION Arisfor WallGuard 1.1 GENERAL A. is a three component polymerized cementitious protective coating that can be applied to a variety of vertical interior and exterior substrates including: stucco, exterior gypsum sheathing,

More information

DECOCOLOR FLOORING SYSTEM

DECOCOLOR FLOORING SYSTEM AIA Specification DECOCOLOR FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions of the

More information

2. In moist areas, portland cement plaster should be used if a more permanent material is not within budget limits.

2. In moist areas, portland cement plaster should be used if a more permanent material is not within budget limits. UDIVISION 9 FINISHES 09 00 00 FINISHES 09 20 00 PLASTER AND GYPSUM BOARD PLASTER 1. Major partitions are to extend to underside of structure as required by code. Allow for structural deflection. Provide

More information

Complementary Coatings Insl-x. Stix Bonding Primer Introduction

Complementary Coatings Insl-x. Stix Bonding Primer Introduction Complementary Coatings Insl-x Stix Bonding Primer Introduction Complementary Coatings: Insl-x Complementary Coatings Corporation is a wholly owned subsidiary of Benjamin Moore & Co Complete Specialty

More information

FLUID APPLIED WATERPROOFING

FLUID APPLIED WATERPROOFING SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.

More information

SPECIFIER SHALL REMOVE COMMENTS IN BOLD TEXT PRIOR TO SUBMITTING.

SPECIFIER SHALL REMOVE COMMENTS IN BOLD TEXT PRIOR TO SUBMITTING. This guide specification is to be used to develop an office master specification or specification for a project. In either case, this guide specification must be edited to fit the conditions of use. Particular

More information

Acrylitex Tilt UP Primer Guide Specification Revised August 1, 2008

Acrylitex Tilt UP Primer Guide Specification Revised August 1, 2008 Acrylic Technologies, Inc. Telephone (503) 653.4061 Fax: (503) 552.1441 Website: www.acrylitex.com Specifier Note: This manufacturer's guide specification specifies Acrylitex Tilt UP Primer for interior

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 096519 - RESILIENT TILE FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

This Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces:

This Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces: 0 0 0 0 0 0 SECTION 0 ANTI- GRAFFITI COATINGS PART - GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division Specification

More information

1.02 SUMMARY A. Section Includes: 1. Repair of two-coat historic exterior vertical plasterwork (stucco)

1.02 SUMMARY A. Section Includes: 1. Repair of two-coat historic exterior vertical plasterwork (stucco) 09 24 00-1 of 7 SECTION 09 24 00 HISTORIC STUCCO MAINTENANCE AND REPAIR PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

Copyright 2018, The Sherwin-Williams Company ISSUED MAY CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY

Copyright 2018, The Sherwin-Williams Company ISSUED MAY CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 67 00 CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL INTERIOR SPECIFICATION GUIDE This Painting Schedule

More information

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS SECTION 03 05 00 COMMON WORK RESULTS FOR CONCRETE 09 97 00 SSPECIALTY COATINGS Weld Crete ************************************************************************************************************************

More information

A. Prepare formwork shop drawings using qualified professional engineer. Include detail of fabrication, assembly, and support of formwork.

A. Prepare formwork shop drawings using qualified professional engineer. Include detail of fabrication, assembly, and support of formwork. DIVISION 03 CONCRETE 03 0100 MAINTENANCE OF CONCRETE 03 0505 UNDER SLAB VAPOR BARRIER A. Sheet vapor retarder shall be polyethylene sheet, ASTM D 4397, 10 mils thick minimum. Consult with Facilities Management

More information

Normal, Medium And High Density Fireproofing Materials

Normal, Medium And High Density Fireproofing Materials Guide Specification Normal, Medium & High Density Fireproofing Materials January 25, 2005 Southwest Fireproofing Products Spray-Applied Fire Resistive Materials Normal, Medium And High Density Fireproofing

More information

SECTION TILING

SECTION TILING PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroBuild XT Extreme Impact & Abrasion Resistant Resurfacing System Part 1: General 1.01 System Description A. Roller applied 100% solids epoxy primer, followed by an extreme

More information

A. This Section includes traffic coatings for the following applications:

A. This Section includes traffic coatings for the following applications: SECTION 071800 - TRAFFIC COATINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes traffic coatings for the following applications: 1. Interior and exterior, pedestrian traffic. 2. Vehicular traffic.

More information

D. Maintenance data for resilient floor tile to include in Operating and Maintenance Manual specified in Division 1.

D. Maintenance data for resilient floor tile to include in Operating and Maintenance Manual specified in Division 1. SECTION 09660 RESILIENT TILE FLOORING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

DUR-A-FLEX, Inc. Page 1 of 5

DUR-A-FLEX, Inc. Page 1 of 5 DUR-A-FLEX, Inc. Page 1 of 5 SECTION 09 67 23-RESINOUS FLOORING DUR-A-GARD EPOXY COATING WITH URETHANE (Armor Top) TOPCOAT (23 mils) Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general

More information

SECTION DETECTABLE GUIDE TACTILES

SECTION DETECTABLE GUIDE TACTILES SECTION 09655 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for surface applied and recessed detectable guide or directional tactiles (tactiles) for use on the station platforms

More information

Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection. NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc.

Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection. NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc. Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc. Cleaning and Protecting Concrete Surface Preparation, Application,

More information

SECTION MISCELLANEOUS METALS THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION MISCELLANEOUS AND ORNAMENTAL IRON

SECTION MISCELLANEOUS METALS THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION MISCELLANEOUS AND ORNAMENTAL IRON SECTION 055000 THIS SECTION TO BE INCLUDED IN SUB BID FOR SECTION 050001 MISCELLANEOUS AND ORNAMENTAL IRON PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a

More information

SECTION PENETRATION FIRESTOPPING PART 1- GENERAL PART 2- PRODUCTS 1.1 RELATED DOCUMENTS

SECTION PENETRATION FIRESTOPPING PART 1- GENERAL PART 2- PRODUCTS 1.1 RELATED DOCUMENTS SECTION 07 8413- PENETRATION FIRESTOPPING PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS

DULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT

More information

Desco Granite Flooring Specifications

Desco Granite Flooring Specifications Desco Granite Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 096813 - TILE CARPETING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information