Technical Data Sheet.
|
|
- Katrina Ryan
- 6 years ago
- Views:
Transcription
1 Technical Data Sheet. Permahyd Hi-TEC Base Coat Series 480 Permahyd Hi-TEC Base Coat Series 480 is an innovative waterborne base coat system. Hi-TEC is fast, versatile, and easy to blend. After recoating with Permacron or Permasolid clear coat, the result is a high gloss, weather resistant finish. This product is for professional painting of vehicles only. VR Technical Data Sheet No. 480 (8/20/2010) Jan. 2011
2 Substrates Suitable Substrates: Substrate pretreatment: Original or old paintwork (except reversible substrates, Example: lacquer) Permacron Primer/Surfacers Permahyd Primer/Surfacers Permasolid Surfacers Degrease and sand. Before further treatment, clean all substrates thoroughly with Permanent Silicone Remover 7010 Slow, Permahyd Silicone Remover 7085, Permahyd or Permahyd Silicone Remover * Permahyd Silicone Remover 7085, or Permahyd Silicone Remover 7096 must be used for final cleaning. Special note: 1. Allow wet sanded surfaces to dry thoroughly. 2. Plastic containers or tins with special lining must be used. 3. Strainers and glue must be waterproof. 4. Strainer must be Micron Nylon Mesh. Application Mixing ratio: 10% Permahyd WT Additive 6050 for solid colors. 20% Permahyd WT Additive 6050 for metallic/pearl colors. Or for low humidity and high temperatures (<30% humidity) 10% Permahyd WT Additive 6051 for solid colors. 20% Permahyd WT Additive 6051 for solid colors. Pot Life: Metallic colors have a 2 4 hour pot life after mixing with Permahyd WT Additive 6050 or Permahyd WT Additive Afterwards it must be reduced again at the same ratio for optimal metallic control. Solid and pearl colors have an extended pot life of 3 6 months after reduction. Method of application HVLP Approved Transfer Efficiency Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. Spray Nozzle mm 1.3 mm Application viscosity 4mm, As mixed 68 F/20 C, DIN 4 Reducer at 68 F/20 C material temperature 10-20% depending on color 1 ½ coat = 1 full coat 6 to 10 inches from panel, followed by 1/2 coat 10 to Number of coats 14 inches from panel keeping overlap at 75% or greater* (*For metallic orientation) * In addition, a control coat may be applied to colors with high metallic/pearl control to improve color match or flake orientation. * With low opacity colors, it may be necessary to apply one or two more coats after an appropriate flash-off time.
3 Three-stage andtwotone finishes Hardener For Three-stage and Two-tone colors, hardener can be added to the basecoat. 5% Permahyd Hardener 3080 (Use in Ground Coat only) Do not use Permahyd Hardener 3080 with WT388 Black. Hardener reduced the pot life of Permahyd Hi-TEC Base Coat Series 480 to 45 to 90 minutes. For under hood colors use 10% Permahyd Hardener Pot life at 10% is 20 minutes. Flash-off time (before clear coat) At 68 F/ 20 C At 140 F/60 Metal Temp. Approximately 20 to 30 minutes. Approximately 10 Minutes. Allow panel to cool to room temp before proceeding. Special Note reducing flash-off time:* Maximum preferred recoat window for Permahyd Hi-TEC Base Coat Series 480 is 72 hours. 1. Small Areas Surface matting can be accelerated by blowing with air diffuser. It is also possible to blow with the spray gun after a waiting time of at least 5 minutes. 2. Larger areas Surface matting can be accelerated by using infra-red or low baking IR medium wave IR short wave cooling time Low baking at 140 F/60 C approx. 4 minutes approx. 3 minutes approx. 5 minutes approx. 10 minutes including heating time * Flash-off and drying times depend on the temperature, humidity, and air flow in the booth, and on the number of coats. The surface must in all cases be allowed to matt completely Further Steps recoat with: Permacron or Permasolid Clear Coats. Permacron or Permasolid VOC Compliant Clear Coats where required.
4 Special Tips 1) The OEM finish dictates whether a two stage or three stage pearl color (with special ground color) is required. The appropriate ground coat color is given on the formula retrieval system. 2) Permahyd Blending Additive 1050 is recommended to reduce the opacity for blending and for use as a wet-bed for blend panels. 3 Blend-in system: Preparation and application of solid and metallic colors 1. Sand Surfacer (dry with P500-P800 or wet sand with P600-P1000). 2. Thoroughly sand surrounding areas not coated with surfacer using a fine sanding pad 3M (Gray) or (Gold). 3. Wash the entire area with Permahyd Silicone Remover 7085, or Permahyd Silicone Remover Apply one full coat of Permahyd Blending Additive 1050 to the surrounding blend area. 5. Apply Permahyd Hi-TEC Base Coat Series 480 to completely cover the surfaced area, overlapping slightly onto the original finish at ready to spray viscosity. 5. After approximately 15 minutes (or when Surface has completely matted) Permacron 2K Clear Coat, Permacron 2.1 Clear Coat or Permasolid HS Clear Coat may be applied. 6. For additional blending recommendations see TDS Use of Permahyd WT Additive 6051 is only recommended when temperature is above 95 F and relative humidity is below 30%. Three stage pearl colors: 1. Apply Permahyd Hi-TEC Base Coat Series 480 (ground color) to completely cover the surfaced area, overlapping slightly onto the original finish. Allow ground coat to flash-off. 2. Apply1 ½ -2 coats of ready to spray Permahyd Hi-TEC Base Coat Series 480 (mid coat color) slightly overlapping this area, so that it matches the original finish. 3. For additional blending recommendations see TDS ) For information on spray equipment please see Technical Data Sheet No Information on cleaning of equipment and waste management can be found in Technical Data Sheet Nos and respectively.
5 Important Regulatory Information Please see the appropriate VOC Wallchart for compliance for your area. The wallchart will reflect appropriate VOC for BC/CC methodology. The values depicted below are as applied regulatory for the coating alone. Values have been determined using EPA Test Method 24. Please see the Master Values List for information for information on individual components. VOC Category VOC Regulatory Density g/l Wt% Volatiles, Water & Exempts Permahyd Hi-TEC 480 Basecoat RTS with 5% Hardener Permahyd Hi-TEC 480Basecoat RTS Vol% Water & Exempts 3.45lb/gal 415 g/l 8.8 g/l 78% 82% 3.5 lbs/gal g/l 8.8 g/l 78% 82% For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Any analytical results set forth herein do not constitute a warranty of specific product features or of the product s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. Storage conditions: Store free of frost! Storage temperature between 42 F/5 C and 95 F/35 C Temperatures above or below this range lead to loss of product quality. SPIES HECKER, INC West Anchor Court Plymouth, MI Tel SPIES Fax
Permahyd Hi-TEC Basecoat 480
Technical Data Sheet Permahyd Hi-TEC Basecoat 480 GENERAL DESCRIPTION Permahyd Hi-TEC basecoat 480 is an innovative waterborne base coat that is fast, versatile, and simple to blend. Hi-TEC provides a
More informationStandox Clearcoat Additives
Standox s Ordering Information: 0.5 Liter Standox Blue 020 16255 0.5 Liter Standox Maroon 020 16256 0.5 Liter Standox Burgundy 020 16257 Features: Current OEM codes: o Ford colors: Z9 & R3 o Toyota colors:
More informationCROMAX PRO WB9908 SUPER JET BLACK BASECOAT
CROMAX PRO WB9908 SUPER JET BLACK BASECOAT GENERAL DESCRIPTION A super jet black factory package color that delivers the deepest black to meet the most critical color standards. It features high hiding,
More informationAutoclear PC FOR PROFESSIONAL USE ONLY. Description. Clearcoat 10/17/2016
Description Autoclear PC is a high solids acrylic urethane clearcoat for use over Sikkens Basecoats. Autoclear PC offers high gloss and is designed for baking conditions. It can be used with a Manual Proportioning
More informationCHROMAPREMIER 72200S PRODUCTIVE CLEARCOAT
CHROMAPREMIER 72200S PRODUCTIVE CLEARCOAT GENERAL DESCRIPTION A three-component, urethane clearcoat for productive premium-quality spot, panel and multipanel repairs. It handles easily, using temperature-specific
More informationCROMAX MOSAIC BASECOAT
CROMAX MOSAIC BASECOAT GENERAL DESCRIPTION A low VOC and 6H compliant (target HAPs free) solvent borne basecoat that delivers true collision repair capability, has excellent color match and meets low VOC
More informationProduct Information. ECS21 White, ECS25 Gray, ECS27 Black A-Chromatic LV Sealer
Product Information ECS21 White, ECS25 Gray, ECS27 Black A-Chromatic LV Sealer Product Description A-Chromatic LV Sealer ESC21, 25 and 27 are premium quality, wet on wet sealers designed specifically for
More informationBasecoat WB FOR PROFESSIONAL USE ONLY
WB Description WB waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. WB must be used in conjunction with
More informationDuPont ChromaClear G2-7779S Multi-Mix Panel & Overall Clearcoat
Description DuPont ChromaClear G2-7779S Multi-Mix Panel and is a versatile, two-component, urethane clearcoat for use in spot, panel, and overall refinishing of OEM base/clear finishes. ChromaClear G2-7779S
More informationCHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER
CHROMAPREMIER 42400S / 42410S / 42440S / 42470S 2K PREMIER SEALER GENERAL DESCRIPTION A three-component, high-performance sealer for premium-quality spot, panel and overall repairs. It provides excellent
More informationUniversal Clear FOR PROFESSIONAL USE ONLY. Description. Clearcoat
Description The Lesonal is an acrylic urethane clearcoat for use over Lesonal Basecoat SB or Lesonal Basecoat WB and intended for applications in cross flow and air dry conditions. offers excellent resistance
More informationUniversal Clear FOR PROFESSIONAL USE ONLY. Description. Clearcoat
02.02.206 Description The Lesonal is an acrylic urethane clearcoat for use over Lesonal Basecoat SB or Lesonal Basecoat WB and intended for applications in cross flow and air dry conditions. offers excellent
More informationAgitate / gently shake the Autowave can prior to use. o Stir color thoroughly prior to adding Activator WB
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Autowave must be used in conjunction
More informationPolybase Plus Basecoat (Low VOC)
Description Polybase Plus is a catalyzed basecoat made from polyester and acrylic resins for use in Automotive and Truck refinishing. Polybase Plus can be used on repairs without swelling, lifting or wrinkling.
More informationMipa WBC 2-Schicht-Basislack Technical data sheet Page 1 / 8
Technical data sheet Page 1 / 8 Intended use Water-based two-layer basecoat to coat completely or partially vehicles, motorbikes and commercial vehicles. Overcoating with Mipa 2K clearcoats results in
More informationNEXA AUTOCOLOR 2K Plastics Painting Process
PDS N7.1 April 2017 NEXA AUTOCOLOR 2K Plastics Painting Process PRODUCT DESCRIPTION The NEXA AUTOCOLOR 2K Plastic Painting Process offers a complete and high quality rage of products for the painting of
More informationAutowave FOR PROFESSIONAL USE ONLY. Description. Basecoat 08/17/2017
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Autowave must be used in conjunction
More informationDuPont ChromaClear G2-4700S (Hyper Cure - Air Dry and Express Bake)
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaClear G2-4700S is a second generation version of ChromaClear 4700S. ChromaClear G2-4700S is not only the world s fastest air
More informationProduct Information. ECS61 White, ECS65 Gray, ECS67 Black A-Chromatic Sealer. Product Description. Preparation of Substrate
Product Information ECS61 White, ECS65 Gray, ECS67 Black A-Chromatic Sealer Product Description A-Chromatic Sealer ECS61White, ECS65 Gray and ECS67 Black are premium quality, wet on wet sealers designed
More informationChromaClear G2-4700S Clearcoat (Hyper Cure - Air Dry and Express Bake)
Description ChromaClear G2-4700S is a second generation version of ChromaClear 4700S. ChromaClear G2-4700S is not only the world s fastest air dry or express bake clear, it also revolutionizes energy savings
More informationJanuary 2007 Product Information ENVIROBASE HIGH PERFORMANCE
GLOBAL REFINISH SYSTEM January 2007 Product Information ENVIROBASE HIGH PERFORMANCE PRODUCTS Envirobase Waterborne Basecoat colour T4xx Envirobase Thinner T494 Envirobase High Performance is waterborne
More informationAgitate / gently shake the Basecoat WB can prior to use. o Stir color thoroughly prior to adding Activator WB
Description Basecoat WB waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Basecoat WB must be used in
More informationDuPont ChromaClear HC-7776S Multi-Mix Snap Dry Clearcoat
Description has Low overspray and fast dust free attributes. It is a tow-component spot and panel clear designed to increase production by maximizing energy savings and vehicle throughput. ChromaClear
More informationOne-coat application 5 LV650 Clear 2 LV650 Hardener 1 LV650 Reducer Anti-Graffiti (#484165)
Description Autocoat BT is a two component VOC compliant clear coat that provides excellent chemical resistance and stain repellent properties. is designed for original equipment and repairs of commercial
More informationGently shake the Autowave can prior to use. Prior to clearcoat application: Until completely matt at 25 C 15 minutes at 25 C
Description Autowave waterborne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl effect colors. Autowave must be used in conjunction
More informationTECHNICAL DATA SHEET EL600 IMRON FLEET LINE CLEAR DESCRIPTION
DESCRIPTION 2-component Low Emission clear, to be used in clear over basecoat system. Composition based on acrylic copolymer. Delivering a high CV quality and a good sagging performance. PRODUCTS ET645
More informationCROMAX PRO WATERBORNE BASECOAT
PRODUCT DESCRIPTION Cromax Pro Basecoat is one of the most technologically-advanced waterborne basecoat available today. It is based on our latest resin, pigment and dispersion technologies to deliver
More informationBasecoat WB Technical Data Sheet 09 / 05 / 2016 L UK & Ireland Basecoats
Description One component, mixing machine water based basecoat system. Available in a wide variety of colours including metallic, pearls and solids. Specifically designed for the refinishing of passenger
More informationCENTARI 501 SUPER PRODUCTIVE 2K ENAMEL
CENTARI 50 Description -component topcoat system for solid colours for use on cars, buses and trucks. Composition based on acrylic copolymer. Products AM Centari MasterTint AF0 Super Productive K Binder
More informationUse suitable respiratory protection Akzo Nobel Car Refinishes recommends the use of a fresh air supply respirator
Description Autobase Plus basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl colour effects. Autobase Plus must be used in conjunction
More informationUse suitable respiratory protection Contains acrylic resins, xylene and other ingredients. When mixed, Autoclear Mat also contains isocyanates.
Description is a high solids acrylic urethane clearcoat for use over Autobase Plus and Autowave. offers high gloss and is designed for baking conditions. It can be used with the Manual Proportioning Unit
More informationa. 100:50:30 Autoclear Mat LV Autoclear Superior 250 Hardener Autoclear Superior 250 Medium Reducer
Description A two component VOC compliant clearcoat with a matt finish. Higher gloss levels can be reached by mixing with Autoclear Superior 250 or Autoclear HS + LV. The main application is to achieve
More informationU280 Single Stage. Check gun manufacture specification HVLP Pressure
Description is two-component, acrylic urethane designed for original equipment and repairs for commercial vehicles. is a cost-effective durable finish with good color capability that is simple to mix and
More informationPolybase Plus Basecoat
Description Polybase Plus is a catalyzed basecoat made from polyester and acrylic resins for use in Automotive and Truck refinishing. Polybase Plus can be used on repairs without swelling, lifting or wrinkling.
More informationLV360 Primer EP 2.1 FOR PROFESSIONAL USE ONLY
Description Autocoat BT LV360 EP 2.1 is a two-component high solids corrosion inhibitive epoxy primer. LV360 Epoxy 2.1 is a low VOC, high solids, HAPs-Free epoxy primer that can be applied as a wet on
More informationIMRON 700 POLYURETHANE ENAMEL
Description 2-component topcoat system designed for application on trucks, buses and light commercial vehicles. Composition based on functional polyurethane. Products AM Centari MasterTint AU170 Polyurethane
More informationHS CLEAR
HIGH SOLIDS ACRYLIC CLEAR HS CLEAR 0300 offers high solid content, fast drying, strong film hardness, and excellent gloss, with the flexibility of different hardener options, and simple mixing ratios for
More informationHS Plus Clearcoat P
J2380 V Product Product Data Sheet October 2018 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HS Plus Clearcoat P190-6570 Description P190-6570 HS Plus Clearcoat P210-8645 HS Plus Hardener Product Description
More informationU500 Single Stage. Check gun manufacture specification HVLP Pressure
Description is two-component, acrylic urethane designed for original equipment and repairs for commercial vehicles. is a cost-effective durable finish with good color capability that is simple to mix and
More informationTechnical Data Sheet. Relevant Products. Recommended Substrates. Substrate Preparation
Euro Colour Description: Euro Colour is a concentrated basecoat for use in clear over systems for solid, metallic and pearl colours. Ease of application and accurate colour matching. Fast dry. Excellent
More informationImron HydroClearCoat. 2K Waterbased Clearcoat PUR. Technical Data Sheet. Description
Description Imron HydroClearCoat HC300 is a waterbased 2-component polyurethane clearcoat especially developed for application on all types of commercial vehicles. Composition based on acrylic resin. Products
More information3.5 HSP (High Solids Polyurethane) Low VOC
Description 3.5 HSP (High Solids Polyurethane) is a single-stage topcoat designed for commercial and automotive refinishing. This product provides Superior UV durability as well as commercial grade chemical
More informationProduct Data Sheet July 2014
Product Data Sheet July 2014 FOR PROFESSIONAL USE ONLY 2K SR Ceramic Clearcoat P190-6512 Product Description P190-6512 2K SR Ceramic Clearcoat P210-8625 2K Hardener for SR Clearcoat P850-1692/1693/1694
More informationProduct Data Sheet July 2017
Premium Surfacer P565-5701, P565-5705 & P565-5707 H5620V Product Data Sheet July 2017 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product Speed Surfacer P565-5801, P565-5805 & P565-5807 Description
More informationUse suitable respiratory protection Contains acrylic resins, xylene and other ingredients. When mixed, Autoclear Mat also contains isocyanates.
Description Autoclear Mat is a two-part acrylic urethane clearcoat with a matt finish. Higher gloss levels can be reached by mixing with any Sikkens urethane clear, i.e. Autoclear III or Autoclear HS +.
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators
Corlar 2.1 PR-P High Solids Productive Epoxy Primer For Use With FG-040, FG-041 or FG-042 Activators GENERAL DESCRIPTION A high solids, two component, high build, VOC conforming (2.1 lbs./gal.) Low HAPS
More informationProduct Information. D814 to plasticise finishes over a flexible substrate
GLOBAL REFINISH SYSTEM May 2016 Product Information D8175 Rapid Performance Clearcoat PRODUCTS UHS Rapid Performance Clearcoat UHS Hardener Accelerator Thinner High Temperature Accelerated Thinner D8175
More information3800S CHROMACLEAR VOC
Description 2-component Low Emission clear, to be used in clear over base system. Composition based on acrylic copolymer and a unique, patented star polymer technology. Products 3800S ChromaClear VOC Low
More informationGRIP-GARD PLUS BRUSH / ROLL ADDITIVE
Description The GRIP-GARD PLUS Brushing/Rolling Additive is designed to convert GRIP-GARD PLUS spray paint into a coating that can be used for brush & roll application. 100 Grip Gard Plus (High Gloss)
More informationTECH MANUAL TABLE OF CONTENTS
PRO-SPRAY TECH MANUAL TECH MANUAL TABLE OF CONTENTS SURFACE CLEANERS 1-1 ICR-0014, ICR-0015, ICR-1402 1-1 SELF-ETCHING & EPOXY PRIMERS 2-1 A-514 CHROMATE FREE ETCH PRIMER 2-1 A-518 EPOXY PRIMER 2-3 PLASTIC
More informationAquabase Plus Waterborne Basecoat System
I0600 Product Data Sheet November 2011 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product Aquabase TM Plus Waterborne Basecoat System Description P989-line Mixed Basecoat Colours P990/991/992/993/
More informationDue to the intrinsic quality the CARIZZMA CANDIZZ should be used only for show cars. CARIZZMA CANDIZZ - small areas, 1-2 panels, e.g.
Product description For CANDYS, an ONYX HD ground coat is sprayed, then the CANDIZZ is sprayed over the top of it, followed by an R-M to finish the look. The CANDIZZS set a new standard of color intensity
More informationImron Super Flow HS Clearcoat
Description 2-component clear based on Low Emission resin high solids technology, to be used in clear over base system. Composition based on acrylic copolymer. Products DP6940 DP2100 DP2110 TH61 TH101
More informationPolyurethane Topcoats. Base material
AkzoNobel Aerospace Coatings Technical Data Sheet Product Group Polyurethane Topcoats Characteristics Product Information is a 3-component basecoat for use in the base coat clear coat decoration system
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer
Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy
More informationProduct Information D8120
Product Information High Solids 2-Pack Clearcoat PRODUCTS Deltron Clear Deltron s D803, D841, D861 Deltron Accelerated D863 Deltron s D870, D807,D872, D873 Deltron DG Fade-out D868 For matt, satin and
More information2K P421 - Single Layer Metallic System Medium Solids. P421-2K Single-layer Metallic colour mixes. P K Air dry lacquer converter
FOR PROFESSIONAL USE ONLY I0320 Date of Issue : July 2002 2K P421 - Single Layer Metallic System Medium Solids Products P421-2K Single-layer Metallic colour mixes P420-/P421-/P425-/P429-2K Mixing basics
More informationIMRON TRAFFIC 2K POLYURETHANE
Description Medium solids 2component topcoat system of the Imron Fleet Line for solid colours for use on buses and trucks. Composition based on functional polyurethane. Products PT PowerTint TR6373 Imron
More informationAQUAMAX Extra Basecoat series 550
PRODUCT DESCRIPTION AquaMax Extra Basecoat is a waterborne basecoat designed for multistage and metallic/pearl effect colours. It has excellent hiding power that delivers high quality and high productivity
More informationSelf Levelling Primer, P , -5605, Self Levelling Primer P , P , P
Product Data Sheet April 2016 FOR PROFESSIONAL USE ONLY Self Levelling Primer P565-5601, P565-5605, P565-5607 Product Description P565-5601 Self Levelling Primer - SG1 P565-5605 Self Levelling Primer -
More informationTechnical Data Sheet FW1 Top coats
Description Wandabase HS polyester basecoat provides quick dry, good hiding and excellent color match. It can be used for small spot repairs and total resprays. 2 Parts Wandabase HS Basecoat 1 Wandabase
More informationIntegral Fuel Tank Coating
Technical Data Sheet Product Group Fuel tank coating Characteristics Product Information - A two-component coating developed as a secondary fuel vapor barrier coating for integral fuel tanks. May be applied
More informationDuPont ChromaPremier 72500S Premium Appearance Clear
cdupont Automotive Finishes ChromaSystem Technical Manual DuPont ChromaPremier 72500S Premium Appearance Clear Description ChromaPremier 72500S is a high-solids, three-component urethane clear that delivers
More informationROCK-IT XC TECHNICAL DATA SHEET
ROCK-IT XC TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rock-It XC is a high quality, urethane, textured coating that provides a durable, chemical and fade resistant, protective finish for truck beds,
More informationAQUAMAX Extra Basecoat - Under Bonnet Repair series 550
PRODUCT DESCRIPTION The AquaMax Extra Basecoat Under Bonnet Repair Process is designed to simplify and speed up repairs to vehicles where the finish in the engine bay area is different to the external
More informationGanicin 2.8 ZR- U Zinc-Rich Polyurethane Primer
Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer GENERAL DESCRIPTION A three-package, VOC conforming (2.8 lbs/gal) low HAPS, zinc-rich urethane primer based on Axalta polyurethane technology. The resulting
More informationJuly 2014 Product Information. Premium UHS Clearcoat (High Temperature)
GLOBAL REFINISH SYSTEM July 2014 Product Information Premium UHS Clearcoat (High Temperature) D8172 PRODUCTS Premium UHS Clearcoat (High Temperature) UHS Hardener D8172 D8302 D8719/D8720 D8172 Premium
More informationROCK-IT XC TECHNICAL DATA SHEET
ROCK-IT XC TECHNICAL DATA SHEET DESCRIPTION Rock-It XC is a high quality, urethane, textured coating that provides a durable, chemical and fade resistant, protective finish for truck beds, recreational
More information100 Wanda Basecoat WB Plus MM 5-10% Wanda WB Plus Activator 10-20% for Metallic Colors
Description Wanda Basecoat WB Plus MM is designed to produce solid, pearl and metallic colors. It has excellent drying properties and can be used for small repairs and total resprays. Mixing ratio 100
More informationDUXONE BASECOAT ACRYLIC BASECOAT
Description A basecoat system for solid, metallic and pearl colours. Suitable for use on cars, trucks and buses. Composition based on acrylic copolymer. Products DX5 DX0 DX11 DX20 DX32 DX34 DX36 DUXONE
More informationPDS N5.9.1 March 2005 P HS CLEARCOAT PRODUCT DESCRIPTION
PDS N5.9.1 March 2005 P190-643 HS CLEARCOAT PRODUCT DESCRIPTION P190-643 is a premium quality High Solids Acrylic Urethane Clearcoat. When combined with Nexa Autocolor Hardeners and Thinners, HS Clearcoat
More informationTechnical Data Sheet CC6400 STANDARD VOC CLEAR. Effective October 5, Description
Description 2-component clear based on Low Emission resin technology, to be used in clear over base system. Composition based on acrylic copolymer and a unique, patented "star" polymer technology. Products
More informationEU-140. D8081 White D8087 Black D8085 Gray D8088 Red. 2K Chromatic Sealer (National Rule) Preparation of Substrate:
2K Chromatic Sealer (National Rule) D8081 White D8087 Black D8085 Gray D8088 Red Product Description: GLOBAL REFINISH SYSTEM 2K Chromatic Sealer (National Rule) D808x, are premium quality primer sealers
More informationGanicin 2.8 ZR-E Zinc-Rich Epoxy Primer
Ganicin 2.8 ZR-E Zinc-Rich Epoxy Primer GENERAL DESCRIPTION A three-package, VOC conforming (2.8 lbs/gal) low HAPS, zinc-rich epoxy primer based on Axalta epoxy amine technology. The resulting organic
More informationAlumigrip 10P8-11 VOC Compliant Epoxy Primer
Technical Data Sheet Product Group Epoxy primer Characteristics - This two component, VOC compliant epoxy primer will provide a very Product smooth finish optimizing the appearance of the subsequent topcoat.
More informationProduct Data Sheet April 2016
Product Data Sheet April 2016 FOR PROFESSIONAL USE ONLY Product Self Levelling Primer P565-5601, P565-5605, P565-5607 (using HS Plus Hardener) Description P565-5601 Self Levelling Primer - SG01 P565-5605
More information58 Series Polyurethane Topcoat
Product Group Polyurethane topcoat Characteristics - This two component high solids polyurethane finish is formulated for Product application to military aircraft, and is designed to provide maximum Information
More information10P20-14 High Solids Low IR Primer
Technical Data Sheet Product Group Epoxy Primer Characteristics Product Information - A high solids primer for aircraft exteriors meeting the low infrared reflectance requirements of the referenced specification.
More informationHS+ Primer Filler P , P & P
Product Data Sheet November 2006 FOR PROFESSIONAL USE ONLY HS+ Primer Filler P565-5301, P565-5305 & P565-5307 Product Description P565-5301 HS+ Primer Filler White Spectral Grey 01 P565-5305 HS+ Primer
More informationTECHNICAL DATA SHEET 1051R / 1057R HIGH PRODUCTIVE SURFACER DESCRIPTION
DESCRIPTION 2-component high solids surfacer with 2 methods of application: a. maxi filler; b. sanding surfacer. Colour: white, black. Composition based on special hydroxy functional acrylic. PRODUCTS
More informationCENTARI 5035 LOW EMISSION 2K TOPCOAT
Description Ultra high solids 2component topcoat system for solid colours for use on cars, buses and trucks. Composition based on a unique, patented star polymer technology. Products AM Centari MasterTint
More informationPolyurethane Topcoats
AkzoNobel Aerospace Coatings Technical Data Sheet Product Group Polyurethane Topcoats Characteristics Product Information is a 3-component durable high gloss polyurethane clear-coat for application on
More informationHS High-Build, Primer Surfacer P /1028. HS High-Build, Primer Surfacer P / Grey / White
Product Data Sheet February 2018 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Product P565-1027/8 Product Description HS High-Build, Primer Surfacer P565-1027 /1028 - Grey / White Description HS High
More informationP WB Engine Bay Basic P Activator for WB Engine Bay Basic P Aquabase Plus Thinner P Aquabase Plus Slow Thinner
Product Data Sheet December 2016 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Aquabase Plus Engine Bay Repair Process Product Description P935-1135 WB Engine Bay Basic P210-9115 Activator for WB Engine
More informationDUXONE Basecoat. All cleaned and sanded OEM finishes (not recommended on thermoplastic acrylic finishes).
Description 2component productive clear to be used in clear over base system. Composition based on a special acrylic polyurethane copolymer. Products 2K HS Clear Coat Activator Slow Standard Activator
More informationVolume Solids % Weight Solids %
Product Name Full Product Name Type of Product Description 1K effect basecoat Chief is an effect basecoat suitable for airbrush application. It is characterised by the most glamorous and vibrant transparent
More informationCENTARI 500 HIGH BUILD 2K ENAMEL
Description 2-component topcoat system for solid colours for use on cars, buses and trucks. Composition based on acrylic copolymer. Products AM Centari MasterTint AK100 2K Binder AK260 High Solids Activator
More informationTechnical data sheet Spectral KLAR 555 Two-component clearcoat with increased scratch resistance (SR)
KLAR 555 Two-component clearcoat with increased scratch resistance (SR) KLAR 555 H 6115 SOLV 855 PLAST 775 S-D10 EXTRA 835 EXTRA 895 RELATED PRODUCTS SR clearcoat Hardener: Fast, Standard, Slow, Extra
More informationKapcibase 670 Basecoat Mixing System
Kapcibase 670 Basecoat Mixing System Product description Kapcibase 670 is a solvent-based basecoat mixing system for repainting of passenger cars and commercial vehicles Kapcibase 670 offers solid color
More informationTechnical data sheet Spectral UNDER 385 Two-component epoxy primer RELATED PRODUCTS
UNDER 385 Two-component epoxy primer UNDER 385 H 6985 PLAST 825 EXTRA 745 RELATED PRODUCTS Epoxy primer Hardener Plastic adhesion increasing agent Filler Dye PROPERTIES Fast-drying epoxy primer Very good
More informationDirect to Metal 2K Urethane High Build Primer
A direct to metal, high build, premium quality, two component, acrylic urethane primer. Primer offers excellent corrosion protec on, adhesion and great sand scratch holdout. Higher solids formula provides
More information2 Lesonal Multi Matt Clear Hardener 3 Lesonal Multi Matt Clear Reducer mm 2 4 * 2 x 1 coat Allow to become matt between coats
Description Low gloss matt clear for application over all Lesonal basecoats. The desired gloss level can be achieved by mixing of the Low Gloss and Semi Gloss components. Mixing ratio 5 2 Hardener 3 Mixing
More informationRepair of two-colour paintwork with ONYX HD on the 208 GTI 30 th, textured finishes
Process Information Description of the repair process: Repair of two-color paintwork with ONYX HD on the is a system designed for the repair of textured finishes of the Peugeot 206 GTI 30 th with ONYX
More informationAlumigrip Technical Data Sheet. Polyurethane Topcoat. Product Group. Characteristics
Technical Data Sheet Product Group Polyurethane Topcoat Characteristics Product Information is a 3-component high solid durable polyurethane topcoat that provides premium gloss and distinctness of image
More informationSurface Sand with P (general area) preparation Use SU WASH COMPOUND or SCOTCH BRITE P1500 (fade out area)
RETAN WB ECO EV 28/Aug./2018 Description RETAN WB ECO EV is state-of- the art water borne base coat. It is not only environmentally friendly but also feels like solvent borne base coat, therefore easy
More informationPercoTop PUR 2K MS Topcoat
Description PercoTop PUR is a 2K polyurethane topcoat. Composition based on highly elastic polyester. Products PercoTop PUR PercoTop PUR CS920 PercoTop PUR Binder CS / PT PercoTop CS / IFL PT Tints CS701
More informationAerowave Technical Data Sheet. Product Group. Epoxy topcoats. Characteristics
AkzoNobel Aerospace Coatings Technical Data Sheet Product Group Epoxy topcoats Characteristics Product Information is a water-based, 2-component, amine cured epoxy finish. - Water based technology - Compatible
More informationPAINT REFINISH FOR SCRATCH SHIELD
PAINT REFINISH FOR SCRATCH SHIELD SERVICE INFORMATION Scratch Shield is a new developed scratch-resistant clear coat which heal by itself when the vehicle gets the small scratch. If the scratch reaches
More information5 STAR XTREME AUTOBODY PRODUCTS TECHNICAL DATA INFORMATION DATED: FEBRUARY 2017 PRODUCT NUMBER DESCRIPTION #5180 ORIGINAL KLEARKOTE 2.
5 STAR XTREME AUTOBODY PRODUCTS TECHNICAL DATA INFORMATION DATED: FEBRUARY 2017 PRODUCT NUMBER DESCRIPTION #5180 ORIGINAL KLEARKOTE 2.1 VOC PRODUCT DESCRIPTION 5180 is a medium solids two component polyurethane
More information3:1 up to 10% Reducer 3 Parts Gray Urethane Surfacer 1 Part Urethane Surfacer Hardener LV Up to 10% Reducer LV Use the Lesonal meauring stick #5
Description Lesonal is intended for use as a high build surfacer that offers excellent filling, easy sanding, and fast dry times. Depending upon the mixing ratio used, Lesonal Gray Urethane Surfacer can
More information