General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.
|
|
- Jean Reed
- 6 years ago
- Views:
Transcription
1
2 General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound. Fasten loose areas with adhesive [contact cement] or pop rivets. Oil or wax must be completely removed. Remove loose portions of existing coatings and brittle caulk with scraper and wire brush. Whatever still has good adhesion may remain to be recoated. Rusty or pitted metal should be wire brushed to remove loose oxide. Tightly adhering corrosion may be coated without a primer. Asphalt based aluminum coatings should be removed as much as possible by wire brush or abrasive disc. Roof cements should be removed and replaced with butyl caulk where necessary. Repair torn sheet rubber by cutting out damage and filling void with a self stick rubber patch. See repair procedure for sheet rubber. Remove chalk from white rubber membrane by brushing with a detergent solution followed by a water rinse or working surface with a stiff brush. Smooth metal or plastic surfaces should be roughed up (sand lightly with 60 grit sandpaper) to improve adhesion of Liquid Roof. A deglossing solvent may work on some plastics. Application: A single application of Liquid Roof is preferable to multiple coats. Touch-ups may be applied as desired after initial film has cured and surface is first wiped with solvent. Apply with brush around flashings and edges using long, slow strokes. On flat surfaces, material can be poured, spread with a squeegee and then evened out with a short nap roller. Liquid Roof will level itself when sufficient material has been applied. Temperature & Cure Conditions: Liquid Roof may be applied at any temperature that permits it being spread onto surface. It will waterproof immediately upon application. the solvent will evaporate at a rate governed by temperature but will not be affected by relative humidity. Exposure to freezing temperatures before cure has taken place will not damage the film. The time necessary to reach cure should not be a concern as this process will occur automatically. Exposure to sunlight will accelerate the curing process. The final film properties of the cured membrane will be the same regardless of the time required to achieve cure. Liquid Roof will provide long term protection even under extreme exposure conditions. Please read all safety precautions and heed all warnings
3 Roof Repairs Made Easy with Liquid Roof Metal & Fiberglass Roofs To Stop Leaks: 1. Use wire brush to clean edge - seal strip, seams and flashings. Use sharp edged spatula to remove cracked or brittle caulk. Rough-up smooth surfaces with sand paper. 2. Apply masking tape where a straight edge is desired leaving 1 1/2" on either side of seam for coating. 3. Apply 1 coat Liquid Roof (catalyzed) with a brush to all seams, flashings and remaining caulk. Top View of RV 4. Remove masking tape the following day after rubber has undergone a partial cure. 20 ft length 36 ft length Total time 1.5 hours 2.5 hours Liquid Roof 2 Quarts 1 Gallon To Repair Cracks: 1. Sand area to 3" around crack. 2. Apply light coat of Liquid Roof. 3. Place polyester fabric into wet rubber over crack. 4. Coat over fabric to ensure a complete seal. Total time Liquid Roof 1/2 hour Part Quart To Repair Metal Rips & Tears: 1. Trim ragged edges of damage. 2. Cut new aluminum plate to overlap damaged area by 3" Drill rivet holes 1/2" 1 from edge 1 1/2" apart. 4. Remove plate and apply rubber over holes. 5. Pop rivet plate and coat over with Liquid Roof , 4 Total time Liquid Roof 1 hour Part Quart
4 Sheet Rubber Roofs To Repair Rips & Tears on Sheet Rubber: 1 1. Make a round or oval cut around damage and remove piece. 2. Use removed piece as a pattern to cut a replacement patch from new self stick rubber Re-glue any loose edges where damaged piece was removed using contact cement Press new patch into cut-out area. It should have a tight fit. 5. Clean new patch plus 4 inches around it by wiping area with paint thinner, xylene or lacquer thinner. 6. Brush apply one coat of Liquid Roof over patch and 2 inches beyond. Repair may be reinforced with polyester fabric if desired. 5 4 self stick patch The above procedure results in a low profile, seamless repair with identical weathering properties of original roof. Total time Liquid Roof 1 hour depending on size of damage Part Quart plywood 6 liquid roof rubber new patch
5 White EPDM Sheet Rubber: White EPDM sheet rubber is now the most widely used roofing material in the RV market. While this material has many advantages over metal and fiberglass it also has some unique characteristics which must be understood before attempting repair procedures. 1. Must be attached to a surface with an adhesive. 2. Will absorb oils, fats and waxes causing the rubber to swell. Since these absorbed materials do not evaporate, the rubber will remain in the swelled state. 3. Will absorb some solvents such as mineral spirits (paint thinner) and cause rubber to swell. This will wrinkle the surface. Solvents, however, will evaporate and the rubber should recover its original shape. This process is slow and could take several weeks before the wrinkles disappear. 4. Solvent absorption and subsequent swelling is substantially reduced if sheet rubber is tightly adhered to surface. 5. Most white sheet rubber is designed to chalk. 6. EPDM rubber should not be coated or mated with materials which do not have a similar low temperature flexibility. Liquid Roof has the same chemical composition, flexibility, and weathering properties as sheet rubber but is Non-chalking. To Stop Chalking 1. Clean surface with stiff brush and detergent or white wall tire cleaner. Rinse with water and let dry overnight. 2. Mask-off perimeter of roof with 2" painter s tape (leave tape overnight before removing) 3. Apply a light coat of Liquid Roof using squeegee, roller and brush. 20 ft 32 ft 36 ft Total time 4 hours 5 hours 6 hours Liquid Roof 2.5 Gal 4 Gal 5 Gal Note: wrinkling will develop one or two hours after application. This condition will recover. Recovery time will vary depending on film thickness and temperature and is usually 1-3 weeks.
6 Useful Information about Liquid Roof Liquid Roof is an EPDM rubber which requires the addition of the premeasured catalyst* before any cure can take place. The rate of cure is determined by the temperature of the surface to which the rubber has been applied. The final properties of the rubber are not affected by the length of time required to achieve cure. Material may be applied at any surface temperature up to 140 degrees F. Liquid Roof can be used to bond porous materials such as fabric and canvas but will not cure between non-porous materials such as rubber, vinyl, plastic and metal. It should primarily be used as a top coating. Liquid Roof will not bond to a wet or damp surface. Liquid Roof is water resistant even in an uncured state. An unexpected rain shower shortly after application may affect the surface appearance but will not wash it off. Uncured Liquid Roof is not damaged by belowfreezing temperatures. The cure reaction will simply be inactive until suitable temperatures return. Product may be used at any temperature which permits application. After the catalyst has been mixed into the rubber, the pot life can be extended for days by keeping material cold in an ice chest [below 50 degrees F]. Asphalt coatings and asphalt built-up roofs are considered unstable substrates and, therefore, not recommended for coating directly with Liquid Roof. A barrier layer of water based Elastromeric Coatings may be applied over the asphalt and then top coated with Liquid Roof, however, warranty will not apply. Materials such as some vinyls which contain high levels of plasticizers and antioxidants may inhibit the cure of Liquid Roof. Liquid Roof may be applied over tightly adhering rust and pitted aluminum. [Apply sufficient material to completely cover rust or pits.] Liquid Roof may be applied directly over weathered but tightly adhering caulks, rubbers, metals, plastics, foam and fabrics. Left over catalyzed material can be saved for future use by refrigerating or freezing in a closed container. Left over material can also be applied to any corroded surface. Coating Sheet Rubber - Solvent from Liquid Roof may be absorbed by sheet rubber and result in swelling and wrinkling. This condition is temporary and will recover as the solvent slowly evaporates. *Note: The catalyst color (dark blue) will have no effect on the color of the cured membrane.
ERSYSTEM ONESTEP PLUS
1 DG0047-A 05/2017 AGED (EPDM, TPO, CSPE-HYPALON, PIB) SINGLE-PLY (THERMOSET) MEMBRANE RESTORATION SYSTEM APPLICATION SAMPLE DESIGN GUIDELINE ERSYSTEM ONESTEP PLUS ITW POLYMERS SEALANTS NORTH AMERICA,
More informationACRYLIC Elastek #127 Solar One Plus
1 EL0017-L 01/2018 AGED (EPDM, TPO, CSPE-HYPALON, PIB) SINGLE-PLY (THERMOSET) MEMBRANE RESTORATION SYSTEM APPLICATION SAMPLE DESIGN GUIDELINE ACRYLIC Elastek #127 Solar One Plus ITW POLYMERS SEALANTS NORTH
More informationPol-E-Base Modified Bitumen Roof System
Pol-E-Base Modified Bitumen Roof System Specification Chemicals, Inc. produces the Pol-E-Base Built-up Roofing System as the ultimate in field applied reflective insulation roofing. It has the advantages
More informationInstruction Guide APPLICATION OF CIM TO ASPHALT
23 Elm St., Peterborough, NH 03458 Tel: (800) 543-3458 (603) 924-9481 Fax: (603) 924-9482 Web site: Instruction Guide APPLICATION OF CIM TO ASPHALT 1.0 DESCRIPTION This guide covers the installation of
More informationInstallation Instructions
Warning: Do not remove outer shrink wrapping from the Fire Rated Foam stick until you have read and understand the FULL instructions for proper installation. Failure to follow these directions may degrade
More informationWabo FireShield Model: FSH
Wabo FireShield Model: FSH Horizontal Expansion Control Fire Barrier System The following installation procedure is very important and must be fully understood prior to beginning any work. To ensure proper
More informationTHE ONLY LIQUID EPDM PRODUCT IN THE WORLD
THE ONLY LIQUID EPDM PRODUCT IN THE WORLD HISTORY OF SUCCESS EPDM Coatings awarded Top 10 Products in Metal Roofing Magazine! Awarded 2011 Top Product by Building Service Magazine EPDM Coatings NE Sales
More information838 Coatings System Specification Single-Ply Restoration (838 SPR)
838 Coatings System Specification Single-Ply Restoration (838 SPR) PART 1 General 1.01 System Description The 838 Single-Ply Restoration System (838 SPR) can be applied to a variety of single-ply manufactures.
More informationInstallation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage
Important Storage Flat sheet - Store Palladium Rigid Sheet in a clean, dry, interior area at temperatures between 50 F and 95 F [10-35 C]. Keep out of direct sunlight. Make sure sheet is well supported.
More informationPRODUCT DATA SHEET LIQUID FLASHING SW
PRODUCT DATA SHEET LIQUID FLASHING SW (summer grade white) is a two component polymethyl methacrylate based (PMMA) liquid flashing material used in Sarnafil and Sikaplan roofing details. is used with Liquid
More informationProduct Data Sheet Waterproofing Membrane for Ponds and Water Features Description Uses Suitable Surfaces Additional Uses Specification
Product Data Sheet Pondseal Waterproofing Membrane for Ponds and Water Features Description Pondseal is a polyurethane / acrylic co-polymer, water based coating which when fully cured, forms an impervious,
More informationEPDM SINGLE-PLY SYSTEM SUMMARY
EPDM SINGLE-PLY SYSTEM SUMMARY This is a generic summary of EDGE s more detailed EPDM SINGLE-PLY SYSTEM SPECIFICATION. For warranty purposes, Approved Applicators are responsible for studying, understanding,
More informationBENEFITS & ADVANTAGES:
APPLICATION GUIDELINES WHITE REFLECTIVE The following KARNAK Roof Restoration System is intended to be applied over sound, dry, existing smooth built-up asphalt and smooth or granular modified bitumen
More informationMAKE ROOFS LAST LONGER
MAKE ROOFS LAST LONGER Roof Coatings & Roof Repair Single-Ply Metal Asphalt HIGHEST PERFORMING SYSTEMS. LOWEST APPLIED COST. METAL ROOF RESTORATION Metal Restoration Quick Guide Acrylic Polyurethane High
More informationTHE ONLY LIQUID EPDM PRODUCT IN THE WORLD
THE ONLY LIQUID EPDM PRODUCT IN THE WORLD HISTORY OF SUCCESS epdm coatings awarded Top 10 products in metal roofing magazine! awarded 2011 Top product by building service magazine EPDM Coatings N.E Sales
More informationTOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets
TOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications
More informationBid Opportunity Wilkes Reservoir North Cell Rehabilitation
Water and Waste MONOMER (EPDM) ROOFING Page 1 of 11 Part 1 General 1.1 REFERENCES.1 ASTM International Inc..1 ASTM D4637-14E1, Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane..2
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationBENEFITS & ADVANTAGES:
APPLICATION GUIDELINES The following KARNAK Roof Restoration System is intended to be applied over sound metal roofing systems with a weathered Kynar coated metal finish. BENEFITS & ADVANTAGES: Elastomeric
More informationTUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE
5 pages TUFF-TAC TM BRIDGE MEMBRANE INSTALLATION GUIDE The following will describe the proper procedure to use when installing Tuff-Tac TM bridge deck membrane. The guide will cover recommended tools to
More informationApplication Specification:
Application Specification: MR-22-GF20 March 2014 Supersedes 10/11 PART 1 - GENERAL 1.1 SUMMARY DIVISION 07 01 50.61: GACO WESTERN GACOFLEX S-20 ELASTOMERIC SILICONE COATING FOR REHABILITATION OF AGED METAL
More informationSILICONE ROOF COATING RESTORATION (RCR) SYSTEM OVER METAL ROOF PANEL
SILICONE ROOF COATING RESTORATION (RCR) SYSTEM OVER METAL ROOF PANEL Part 1. 1.1 Description General Conditions A. Scope of Work Provide all materials, labor and equipment required for the installation
More informationProtective Industrial Polymers - USA Manufacturer s Specification February 11, 2015
This specification covers InhibiChem SR-GF-L Enhanced Chemical and Solvent-Resistant Glass-Flake Reinforced Steel Tank Lining System. This system consists of a vinyl ester primer, and two troweled coats
More informationInstruction Guide APPLICATION OF CIM TO CONCRETE
23 Elm St., Peterborough, NH 03458 Tel: (800) 543-3458 (603) 924-9481 Fax: (603) 924-9482 Web site: Instruction Guide APPLICATION OF CIM TO CONCRETE 1.0 DESCRIPTION This guide covers the installation of
More informationApplication Specification:
Application Specification: MR-30-GF20 March 2014 Supersedes 10/11 PART 1 - GENERAL 1.1 SUMMARY DIVISION 07 01 50.61: GACO WESTERN GACOFLEX S-20 ELASTOMERIC SILICONE COATING FOR REHABILITATION OF AGED METAL
More informationCIM IG 13 11/06. Instruction Guide
23 Elm St., Peterborough, NH 03458 Tel: (800) 543-3458 (603) 924-9481 Fax: (603) 924-9482 Web site: Instruction Guide APPLICATION OF CIM 2000 TO CONCRETE 1.0 DESCRIPTION This guide covers the installation
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists
More informationA. Submit product data sheets and literature verifying physical properties of materials.
I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving EPDM Roofs 07500 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide labor,
More informationMaster-Seal Surface-Applied Waterproofing System
P 1/7 INDUSTRIAL ROOFING, INC. Master-Seal Surface-Applied Waterproofing System Master-Seal is a highly effective waterproofing system designed to seal surfaces from water seepage in roofs with minimum
More information1.04 REFERENCES STANDARDS.1 For reference standards tests & results refer to Manufactures Product Data Sheets
This specification covers InhibiChem CR-GF-L Chemical-Resistant Glass Flake-Reinforced Steel Tank Lining System. This system consists of a vinyl ester primer, and two troweled coats of glass flake filled
More informationFireShield Restoration Specifications - EPDM
FireShield Restoration Specifications - EPDM Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com FIRESHIELD Restoration Specifications EPDM PART 1 GENERAL
More informationSECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.
Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call
More informationApplication Specification:
Application Specification: MR-38-GF20 May 2014 Supersedes 10/11 PART 1 - GENERAL 1.1 SUMMARY DIVISION 07 01 50.61: GACO WESTERN GACOFLEX S-20 ELASTOMERIC SILICONE COATING FOR REHABILITATION OF AGED METAL
More information3,Rothwell Street, Timaru, South Canterbury. ; : Phone or
ECO-SEAL 100 3,Rothwell Street, Timaru, South Canterbury Email; ideaslab64@gmail.com : Phone +64 3 688 5508 or 0275 239888 Two Pack Flexible Self Priming high hysteresis waterproofing membrane designed
More informationSECONDARY CONTAINMENT COATING SPECIFICATION
SECONDARY CONTAINMENT COATING SPECIFICATION 1.0 GENERAL PROVISIONS Applicable to the following areas: Typical concrete secondary containment structure with occasional exposure acidic and alkaline compounds
More information.2 Flashings at grade to extents shown on the Drawings. .3 Membrane and polyethylene slip sheets at perimeter of walls.
RWPS Foundations and Concrete Structures Page 1 of 8 1. GENERAL 1.1 Work Included.1 Supply and installation of ethylene propylene diene monomer (EPDM) membrane and insulation to extents shown on the Drawings
More informationSECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Seal
SECTION 07550 MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Seal This section is based on the products of MFM Building Products Corp., which is located at: 525 Orange St. P. O. Box 340 Coshocton, OH 43812
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING
More informationCopolymer BEFORE. Copolymer DURING. Copolymer AFTER. (800) TRI-CHEM 3
Roof Repair Copolymer BEFORE Copolymer DURING Copolymer AFTER www.tri-chem.com (800) 456-6255 TRI-CHEM 3 TECHNICAL DATA SHEET TRI-MEMBRANE DESCRIPTION Tri-Membrane is an asphalt impregnated cotton membrane
More informationData Sheet Eco-Smart Membrane WS M1
Water-based Acrylic WS M1 Elastomeric Waterproofing Membrane is a durable, multi-use, extremely durable acrylic coating. At an ideal wet film thickness of 10-14 mils per coat (8-10 mils dry film finish
More informationRG180 FIBERED ELASTOMERIC 15yr System/ Metal Roofs
RG180 FIBERED ELASTOMERIC 15yr System/ Metal Roofs PART 1 - GENERAL 1.01 Description of Work A. This general specification is for the application of a Roof Guardian Technologies (RGT) Elastomeric Coating
More informationRG-170 Elastomeric 15yr System/ Metal Roofs
RG-170 Elastomeric 15yr System/ Metal Roofs PART 1 - GENERAL 1.01 Description of Work A. This general specification is for the application of a Roof Guardian Technologies (RGT) Elastomeric Coating system
More informationThere are many surface contaminants that can interfere with coating adhesion. The following are the most common:
ATB-103 General Coating Preparation Guidelines Introduction In real estate, the key phrase is Location! Location! Location! With paints and coatings, the phrase is Preparation! Preparation! Preparation!
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationSOLAR COATING SYSTEMS SYSTEM EMULSION /ACRYLIC. Specification for Built-Up Roofing MULSION/A 1.01 SUMMARY
SOLAR COATING SYSTEMS 2-PLY EMULSION MULSION/A /ACRYLIC SYSTEM Specification for Built-Up Roofing 07590 PART 1. GENERAL 1.01 SUMMARY Name Address City, State, zip A. Furnish and install a seamless, reinforced
More informationReflectiClean Acrylic/Urethane
1 DG0009-J 08/2015 Metal Roof Restoration Sample Design Guidelines ReflectiClean Acrylic/Urethane ITW POLYMERS SEALANTS NORTH AMERICA, INC. 111 S. Nursery Road. Irving, TX 75060 Tel: 972-438-9111 Fax:
More informationPEKAY T570 RUBBERSEAL
PEKAY T570 RUBBERSEAL DESCRIPTION Pekay Rubberseal T570 is a rubber-latex modified anionic bitumen emulsion, which dries to a pliable, flexible, waterproof, black coating. It may be used for a variety
More informationBRANZ Appraisal Certificate # 461 (2010) Internal wet areas.
SPECIFICATION FOR PROTECTO WRAP AFM-WM FOR INTERNAL WET AREAS BRANZ Appraisal Certificate # 461 (2010) Internal wet areas AFM/WM INTERNAL 0104 Page 1 AFM-WM INTERNAL SPECIFICATION PRODUCT DESCRIPTION Anti
More informationRG180 FIBERED ELASTOMERIC 10yr System/ Metal Roofs
RG180 FIBERED ELASTOMERIC 10yr System/ Metal Roofs PART 1 - GENERAL 1.01 Description of Work A. This general specification is for the application of a Roof Guardian Technologies (RGT) Elastomeric Coating
More informationINDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES. Four-Side Interlock Loose Lay Installation
INDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES Four-Side Interlock Loose Lay Installation The following pages are guidelines only... please read this manual thoroughly
More informationInstructions for On-Site Coating of Vinyl Windows
www.aqua-diy.com Instructions for On-Site Coating of Vinyl Windows Aqua DIY D100 is a high performance heat reflective water-based coating. It has been shipped to you with a thickness suitable for manual
More informationPermaroofUK. Frequently asked questions
PermaroofUK Frequently asked questions What is Firestone RubberCover membrane? Firestone RubberCover EPDM is a 100% cured single-ply roofing membrane made of a synthetic rubber Ethylene-Propylene-Diene
More informationACRYLIC. AGED (PVC, CPE, CPA) SINGLE-PLY (Thermoplastic) Membrane Restoration Sample Design Guideline
1 DG0013-J 04/2017 AGED (PVC, CPE, CPA) SINGLE-PLY (Thermoplastic) Membrane Restoration Sample Design Guideline ACRYLIC ITW POLYMERS SEALANTS NORTH AMERICA, INC. 111 S. Nursery Road. Irving, TX 75060 Tel:
More informationEPDM ROOF RESTORATION
EPDM ROOF RESTORATION This guide specification governs the installation of thermoplastic rubber coatings for the repair and resurfacing of fully adhered and mechanically fastened EPDM membranes. The use
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Single Quartz Broadcast System GUIDE SPECIFICATION SECTION
More informationDURA 500 THERMOPLASTIC FLAT ROOF COATING SYSTEM BY SUPERIOR POLYMERS INC.
SPECIFICATION GUIDELINE FOR SMOOTH ROOF SUBSTRATES INCLUDING MODIFIED BITUMEN, SMOOTH ASPHALT, EPDM, TPO, AND PLYWOOD. Part 1 General Information For the purpose of clarification in this document, the
More informationRead the following instructions prior to application. Europe
of wall printable Read the following instructions prior to application 1. Prior to application or lamination, prints must be sufficiently dried in order to prevent any negative effects on film or adhesion
More informationFully Adhered EPDM. Installation Instructions. Single-Ply Simplified
Fully Adhered EPDM Installation Instructions Single-Ply Simplified P.O. Box 251 Plainfield, PA 17081 866.471.5125 FAX: 717.960.4034 www.weatherbondroofing.com 2018 WeatherBond. 03.26.18 REPRINT REQUEST
More informationPacific Polymers Elasto-Deck 5000MR Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide
More informationSILICONE ROOF COATING RESTORATION (RCR) SYSTEM OVER GRAVEL SURFACE BUR
SILICONE ROOF COATING RESTORATION (RCR) SYSTEM OVER GRAVEL SURFACE BUR Part 1. 1.01 Description General Conditions A. Scope of Work Provide all materials, labor and equipment required for the installation
More informationSECTION A. American Society for Testing and Materials (ASTM):
hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Sparse Flake System GUIDE SPECIFICATION SECTION 09725
More informationTHE BRITE THING TO DO
REDUCING ENERGY CONSUMPTION IMPROVING AIR QUALITY THE BRITE THING TO DO BRITE-n-EZ Enhanced Coating Application Process on Black EPDM Roof Membrane BRITE-n-EZ EPDM Application Instructions CLEANING Remove
More informationROCK-IT XC TECHNICAL DATA SHEET
ROCK-IT XC TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rock-It XC is a high quality, urethane, textured coating that provides a durable, chemical and fade resistant, protective finish for truck beds,
More informationWATERPROOFING. MiraPLY Installation Instructions SCIENCE. SERVICE. SOLUTIONS. Introduction. Description. Substrate Preparation. Features and Benefits
Introduction Carlisle Coatings & Waterproofi ng Incorporated (CCW) has prepared this installation guide to assist applicators in the use of MiraPLY and accessories. Every project is different, and this
More informationAcrylic/Urethane. Metal Roof Restoration Sample Design Guideline
1 DG0009-I 04/2017 Metal Roof Restoration Sample Design Guideline Acrylic/Urethane ITW POLYMERS SEALANTS NORTH AMERICA, INC. 111 S. Nursery Road. Irving, TX 75060 Tel: 972-438-9111 Fax: 972-554-3939 www.itwsealants.com
More information1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels. 3. Insulation. 4. Plaza deck pavers.
SECTION 071413 HOT FLUID APPLIED RUBBERIZED ASPHALT WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels.
More informationEFFISUS EASYREPAIR MEMBRANE
Effisus Easyrepair Membrane EFFISUS EASYREPAIR MEMBRANE DESCRIPTION For use on virtually all roofs, Effisus Easyrepair Membrane features an UV stable backing that is available in Black, Gray, Tan, and
More informationApplication Guide GARAGE & COMMERCIAL FLOORS
Application Guide GARAGE & COMMERCIAL FLOORS REQUIRED TOOLS & MATERIALS - CHECKLIST Flexstone Coatings products (ensure you have enough) Flat Squeegee and Pole (Optional) Disposable brushes (3-4 ) Roller
More informationBlue Barrier Liquid Wrap 2300
Tools/Materials Needed 5 gal pail of PolyWall Blue Barrier Liquid Wrap 2300 10.1 oz Caulking Tube of Poly Wall Blue Barrier 2200 Joint Filler Caulking gun 9 to 11-inch Hot Dog Style Roller handle and Mini
More informationRubber Roofing Pocket Application Guide
Rubber Roofing Pocket Application Guide Table of Contents Page 2.......................... General Information Page 2........................ Cautions and Warnings Page 3.......................... Recommended
More informationGENERAL GUIDELINE SikaMembran System / VERSION 1 / SIKA SERVICES AG
GENERAL GUIDELINE 01.09.2017 / VERSION 1 / SIKA SERVICES AG TABLE OF CONTENTS 1 PURPOSE AND GENERAL INFORMATION 3 2 INTRODUCTION 4 3 AREAS OF APPLICATION 4 4 MEMBRANE SELECTION AND DESIGN 6 5 WORKING PLACE
More informationFLUID APPLIED WATERPROOFING
SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.
More informationInstallation Instructions
Installation Instructions Before you begin, you will need the following tools and supplies: A clean or new 5 gallon bucket. You will need to either replace or clean your bucket after each 5 kits or before
More informationROCK-IT XC TECHNICAL DATA SHEET
ROCK-IT XC TECHNICAL DATA SHEET DESCRIPTION Rock-It XC is a high quality, urethane, textured coating that provides a durable, chemical and fade resistant, protective finish for truck beds, recreational
More informationPacific Polymers Elasto-Deck 5000X2 Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide
More informationSection Pre-Applied Sheet Membrane Waterproofing
Section 071324 Pre-Applied Sheet Membrane Waterproofing PART 1 GENERAL 1.01 SUMMARY A. The Work of this Section includes, but is not limited to, pre-applied sheet membrane waterproofing that forms an integral
More informationDATA SHEET DEKSTER 131 SELFLEVELLING FLOOR COAT / UNDERLAY
(Page 1 of 8 ) GENERAL DESCRIPTION - Dekster 131 self levelling is a contemporary coating that achieves hard wearing, utilitarian floor surfaces in a range of natural tones to offset any style of interior.
More informationA. Submit product data sheets and literature verifying fire ratings and physical properties of materials.
I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving BUR & Mod Bit Roofs 07560 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide
More informationThe Cool Roofing Solution
The Cool Roofing Solution & Product Guide BEFORE AFTER The Cool Roofing Solution Before After What is a cool roof? A cool roof is one that reflects and releases the sun s energy away from the building
More informationEVOCOAT HYBRID
F/T 008 1/2 EVOCOAT HYBRID 5503-450 CHEMICAL DESCRIPTION Evocoat Hybrid 5503-450 is fast setting, rapid curing, 100% solids, flexible, aromatic, two component hybrid polyurea spray system that can be applied
More informationMaximum Rust Protection!
ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric
More informationBACKSTOP NT - Texture A high performance, non-cementitious water-resistive membrane and air barrier. Backstop NT - Texture Application Instructions
BACKSTOP NT - Texture A high performance, non-cementitious water-resistive membrane and air barrier Backstop NT - Texture Application Instructions CHECKLIST PRIOR TO THE INSTALLATION OF BACKSTOP NT TEXTURE
More informationTRUCKBED LINER TECHNICAL DATA SHEET
TRUCKBED LINER TECHNICAL DATA SHEET DESCRIPTION Truckbed Liner is a two component, urethane, textured coating that provides superior adhesion, film build and flexibility to truckbeds and restoration projects.
More informationTOPCOAT System Specifications Corrugated Transite Panels
TOPCOAT System Specifications Corrugated Transite Panels Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT System Specifications Corrugated Transite
More informationCCW MiraPLY Installation Instructions
CCW MiraPLY Installation Instructions www.carlisleccw.com Support: 800.527.7092 Introduction Carlisle Coatings & Waterproofi ng Incorporated (CCW) has prepared this installation guide to assist applicators
More informationMEMBRANE 510/510R Low VOC Flexibilized, Urethane Membrane mils
GREEN BUILDING FEATURES Contributes towards satisfying Credit 4.2 under LEED Contains recycled post industrial crushed glass Contains rapidly renewable materials Meets California South Coast Air Quality
More informationHIGH PERFORMANCE WATERPROOFING TAPE WATERPROOFING TAPE THAT PERMANENTLY BONDS AND SEALS TO ALMOST ANY SURFACE
HIGH PERFORMANCE WATERPROOFING TAPE WATERPROOFING TAPE THAT PERMANENTLY BONDS AND SEALS TO ALMOST ANY SURFACE SIMPLE, RAPID REPAIRS FOR ROOFS Permanently bonds and seals to almost every construction material
More informationRD COATINGS -RD-ELASTOFLEX ELASTOMERIC ACRYLIC WALL COATING SPECIFICATION
RD COATINGS -RD-ELASTOFLEX ELASTOMERIC ACRYLIC WALL COATING SPECIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions,
More informationSection Fluid-Applied Roofing. Modified Bitumen Roof Preservation System Master Guide Specification
Section 07560 Fluid-Applied Roofing Modified Bitumen Roof Preservation System Master Guide Specification 1 PART 1 GENERAL 1.1 RELATED WORK SPECIFIED ELSEWHERE A. Rough Carpentry: Section 06100 B. Board-Stock
More informationSelf Adhesive EPDM TRAINING MANUAL
Self Adhesive EPDM TRAINING MANUAL Rubber4Roofs Ltd, Unit 4 Kingswood Close Page 1 of 7 Copyright Rubber4Roofs Ltd GeneralHealth&Safety Extreme care must be exercised when working on ladders, roofs, below
More informationA-9,250 Parking Structure Resurfacing Cement Look
A-9,250 Page 1 A-9,250 Parking Structure Resurfacing Cement Look Description This specification includes the repair and resurfacing methods used when applying Americrete products over cracked, spalled,
More informationSOLAR COATING SYSTEMS ACRYLIC RENOVATION ROOF 4.5. Specification for Built-Up Roofing SUMMARY
SOLAR COATING SYSTEMS ACRYLIC ROOF RENOVATION 4.5 Specification for Built-Up Roofing 07590 PART 1. GENERAL 1.01 SUMMARY NAME ADDRESS A. Furnish and install a seamless, waterproof spray applied elastomeric
More informationSoft Grip. WATERBASED Anti-Slip Coatings
Soft Grip WATERBASED Anti-Slip Coatings Soft Grip Coatings have been formulated for use on FIBERGLASS, CONCRETE, WOOD and PRIMED METAL surfaces. When used properly, these products provide a tough, anti-slip
More informationASPHALT CEMENTS & COATINGS. Roof Mastics Protective Asphalt Coatings Asphalt Primers Aluminum Coatings
ASPHALT CEMENTS & COATINGS Roof Mastics Protective Asphalt Coatings Asphalt Primers Aluminum Coatings ROOF MASTICS #211 PLASTIC CEMENT Mule-Hide #211 Plastic Cement is a general purpose formulation for
More informationDO-IT-YOURSELF SELF ADHESIVE PLANK INSTALLATION
Woodland Creek Series Self-Adhesive Residential Vinyl Plank Pattern Numbers: Sku 725-6664 PLK1102 Sable Sku 725-6666 PLK1106 Gray Wolf DO-IT-YOURSELF SELF ADHESIVE PLANK INSTALLATION MATERIALS YOU MAY
More informationInstallation Data PSL/R, PSML/R, PSTL/R, PSTML/R, PSL/R, PSML/R, PSTL/R, PSTML/R
Read and follow all instructions prior to installing your Aquatic Bath fixture. Save these instructions for future reference. Failure to comply with these instructions may invalidate your warranty. For
More informationSECTION mil thickness REINFORCED LIQUID-APPLIED WATERPROOFING
SECTION 07143 CCW-MIRASEAL @ 120 mil thickness REINFORCED LIQUID-APPLIED WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Installation of waterproofing membrane on surfaces indicated on drawings, consisting
More informationDivision 7-Moisture Protection Section 7-Under Tile Waterproofing Exceeds ANSI A Rev. 05/2012 Page 1
Page 1 Table of Contents General... 2 Approvals... 2 Applicator... 2 Product Delivery, Storage and Handling... 2 Limitations... 2 Safety... 2 Tools Needed for Application... 2 Products... 2 AVM System
More informationMETHOD STATEMENT SIKALASTIC -680 AP SIKA LIMITED (VIETNAM)
METHOD STATEMENT SIKALASTIC -680 AP SIKA LIMITED (VIETNAM) 1 SCOPE This method statement describes the step by step application of 1-component component, liquid applied, highly elastic polyurethane waterproofing
More informationStudent Services & Classroom Addition
SECTION 071326 - SELF-ADHERING SHEET WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information