PROCEDURE. GTT (GAZ TRANSPORT & TECHNIGAZ) Mk III, Mk V & NO96 MEMBRANE CONTAINMENT SYSTEMS GENERAL APPROVAL AND SUPPLY OF MATERIALS AND COMPONENTS
|
|
- Jane McGee
- 6 years ago
- Views:
Transcription
1 PROCEDURE GTT (GAZ TRANSPORT & TECHNIGAZ) & MEMBRANE CONTAINMENT SYSTEMS GENERAL APPROVAL AND SUPPLY OF MATERIALS AND COMPONENTS 1. It is necessary for materials and component parts of the containment system to comply with relevant Gas Code and Rule requirements in respect of their properties (Rules for Gas Ships section LR 6.8). This General Approval procedure sets out a standard for all materials and components. 2. GTT have produced a set of material and component specifications ( M3XXX Specifications ) for each type of the significant materials and components used on the and systems. The latest versions of the M3XXX Specifications are listed below for reference and may be considered as being correct as of the date of issue of this procedure. The versions of these documents held by the shipyard and intended to be used for the vessel / project being considered should be consistent with the approved List of Generic Documents Applicable to the Project ( Gen List ) for that vessel/project. Table 1. GTT Material / Component Specification Status GTT System (1) Material / Component GTT Specification No. Latest Version (2) Latest Version Date LR comments to be taken account of in conjunction with the GTT Specifications (Reference, Date) (3) All Specifications for GTT Materials - Guidelines M January 2016 All Specification for GTT Prefabricated - Guidelines M January 2016 Paint for Inner Hull Protection M December 2015 Inner Hull Studs, Nuts & Washers M November 2015 Load Bearing Mastic M January 2016 All Adhesive M3005 (4) 02 November 2015 Mk III Adhesive for Secondary Barrier M3006 C February 2010 Reinforced Polyurethane Foam [R-PUF] M3007 (7) 03 November 2015 High Density Reinforced Polyurethane Foam [HD R-PUF] M November 2015 Low Density Foam [LDF] M December 2015 Mk III Plywood M March 2015 Mk III Densified Wood Laminate M3012 (8) B January 2008 Stainless Steel Sheets [Thickness < 3 mm] M November 2015 Stainless Steel Sheets [Thickness > 3 mm] M November 2015 Stainless Steel Studs, Nuts and Washers M November 2015 All Glass Wool M November 2015 Glass Cloth M3017 B January 2008 MTES/HULL/ , 16/02/2016 MTES/HULL/ , 16/02/2016 MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , LDSS/SST/I , 13/05/2010 MTES/HULL/ , MTES/HULL/ , 25/03/2015 MTES/HULL/ , MTES/HULL/ , MTES/HULL/ ,
2 All Staples M November 2014 Fe - 36% Ni Alloy strips [Invar] M3020 B January 2008 All Thermal Protection M3022 B January 2008 Anti-sticking film M October 2013 Mk III Adhesive M3024 (5) B January 2008 Glass Wool [for Insulating Box] M June 2012 & FE-36%Ni Welding Filler Metal M December 2015 Fe 36% Ni Alloy Sheets M November 2015 Mark V Plywood M November 2015 Bridge Adhesive M November 2015 Mk III Secondary Barrier M3101 (6) C February 2010 Mk III Top Bridge Pads Prefabricated M January 2015 Mk III Flat Wall Panels Prefabricated M January 2015 Mk III Corner Panels Prefabricated M January 2015 Expansion Rivets 15mm M November 2015 Mk III Stainless Steel Corners M3108 B November 2011 Anchor Strips M November 2015 Primary Barrier Components M December 2015 Mk III Single Legs Prefabricated M January 2015 Mk III Primary Block Assembly Prefabricated M January 2015 Expansion Rivets - 21mm M November 2015 Anchor Strips for Secondary Barrier M November 2015 Stainless Steel Corner with Fixing Holes M November 2015 Metallic Secondary Barrier M November 2015 Primary Anchoring Cross and Plate M November 2015 Secondary Membrane Trihedron M November 2015 Mark V: Secondary Flat Panel Prefabricated Mark V: Primary Flat Panel Prefabricated Mark V: Secondary Corner Panel Prefabricated M November 2015 M November 2015 M November 2015 Mark V: Single Leg Prefabricated M November 2015 Mark V: Primary Corner Panel Prefabricated M November 2015 Mark V: Primary Key Prefabricated M November 2015 Perlite M3501 A January 2007 Plywood M3502 A January 2007 Insulating boxes M3503 C March 2013 Insulating material M3504 A January 2007 & -L-03: Reinforced Polyurethane Foam [R-PUF] M September 2012 MTES/HULL/ , 05/01/2015 MTES/HULL/ , 06/11/2013 LDS/HULL/ , 11/07/2012 MTES/HULL/ , MTES/HULL/ , LDSS/SST/I , 13/05/2010 MTES/HULL/ , LDS/SST/ /A, 09/11/2012 MTES/HULL/ , MTES/HULL/ , 22/03/2016 MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , 22/03/2016 MTES/HULL/WP , MTES/HULL/WP , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , MTES/HULL/ , LDS/HULL/ , 27/03/2013 LDS/HULL/ , 27/09/2012 Collar studs [forged] M November 2015 MTES/HULL/ ,
3 & Self-locked nuts M July 2016 Load bearing mastic M3508 B January 2008 Glue M3509 A January 2007 & Spring washers M November L03: Flat Wall Panels M January 2015 Plywood Cleat M January 2015 Wood screws M December 2014 SOUTSO/HULL/ /02/2017 SOUTSO/HULL/ /04/2017 MTES/HULL/ , 05/05/2015 MTES/HULL/ , 05/05/2015. MTES/HULL/ , 23/12/2014 Notes: (1) Mk III material/components approvals should be considered to cover Mk III Flex, and material/components approvals should be considered to cover L03, unless otherwise specifically indicated. (2) It may be that the specification version being proposed by the shipyard is not the latest version. This is acceptable provided it is the version shown on the approved Gen List. (3) MTES/Structures should be contacted for information on the comments which are to be taken account of where indicated in the final column of Table 1. (4) This adhesive is used for the insulation panel assembly. (5) This adhesive is used for bonding the secondary barrier to the pump tower base support (PTBS) & to Stainless Steel Plate in Liquid Dome and Gas Dome Area. (6) This specification covers both the rigid secondary barrier material (RSB) and the flexible secondary barrier material (FSB). (7) In case there is an intention to reduce the insulation thicknesses (or decrease the boil-off rate) of Mk III or Mk III Flex designs based on the low thermal conductivity of this foam, then thermal conductivity confirmatory testing is required witnessed by an LR attending Surveyor. (8) This material was used for the hardwood keys on the old rectangular PTBS design. There are no hardwood keys fitted on the conical PTBS design and therefore this material is no longer used on Newbuilding projects. 3. Approvals 3.1 The following table lists the materials/components of the and containment systems and gives the approval and submission requirements for each material/component. Only those materials/components identified by the column General Approval will require General Approval under this scheme. Batches of completed materials/components require survey or provision of certificates of conformity as identified by the column Batch Testing. Table 2. Approval Requirements Materials Approval Batch Testing GTT System Material / Component Manufacturer approved by LR General Approval Survey of completed materials / components by LR Surveyor at place of manufacture (1) Certificates of conformity for each delivery to be provided to attending LR Surveyor (2) All Adhesive [M3005] - - All Glass Wool - - All Thermal Protection All Staples - - (11) All Paint for Inner Hull Protection -,,,, (10), (13) - Glass Cloth - - FE-36%Ni Welding Filler Metal (14) - - Collar studs [forged] Self-locked nuts Spring washers (6) Inner Hull Studs, Nuts & Washers (4) Load Bearing Mastic [M3004] - - Reinforced Polyurethane Foam [R-PUF] - - High Density Reinforced Polyurethane Foam [HD R-PUF] - -
4 Low Density Foam [LDF] Stainless Steel Sheets [Thickness < 3 mm] (5) - - Stainless Steel Sheets [Thickness > 3 mm] (5) - - Stainless Steel Studs, Nuts and Washers (5) - - Expansion Rivets 15mm Anchor Strip [M3109] (5) - - Primary Barrier Components (16) - - Fe 36% Ni Alloy Sheets [Invar, M3028] (14) - - Mark V Plywood - (12) - Bridge Adhesive - - Expansion Rivets - 21mm Anchor Strips for Secondary Barrier (5) - - Stainless Steel Corner with Fixing Holes (16) - - Metallic Secondary Barrier (15) - - Primary Anchoring Cross and Plate (16) - - Secondary Membrane Trihedron (15) - - Mark V: Secondary Flat Panel Prefabricated (3) - (9) - Mark V: Primary Flat Panel Prefabricated (3) - (9) - Mark V: Secondary Corner Panel Prefabricated (3) - (9) - Mark V: Single Leg Prefabricated (3) - (9) - Mark V: Primary Corner Panel Prefabricated Mark V: Primary Key Prefabricated (3) - (9) - Mk III Adhesive for Secondary Barrier [M3006] - - Plywood [M3010] - (12) - Mk III Densified Wood Laminate - (12) - Mk III Adhesive [M3024] - - Mk III Secondary Barrier - - Mk III Top Bridge Pads Prefabricated (3) - (9) - Mk III Flat Wall Panels Prefabricated (3) - (9) - Mk III Corner Panels Prefabricated (3) - (9) - Mk III Stainless Steel Corners (16) - - Mk III Single legs Prefabricated - (9) - Mk III Primary Block Assembly Prefabricated Fe - 36% Ni Alloy strips [Invar, M3020] (14) - - Anti-sticking film Glass Wool [for Insulating Box, M3026] - - Perlite - - Plywood [M3502] - (12) - Insulating boxes - (12) - Insulating material - - -L-03: Reinforced Polyurethane Foam [R-PUF, M3505] - - Load bearing mastic [M3508] - - Glue [M3509] - - No96-L03: Flat Wall Panels [M3511] - (12) - Plywood Cleat - (12) - Wood screws (11) Invar tubes, and other prefabricated invar components - - (8) - Coupler sockets [forged] (6) - - Coupler rods, set plates (1), (7) - - Notes: Required. - Not required. (1) If the components are fabricated within the shipbuilder s premises and inspected by the attending LR Surveyors during the construction of the ship, then the certificate need not be issued except if requested by the Owners or Shipbuilders themselves. (2) A Certificate of Conformity is a certificate issued by the manufacturer of the particular component / material being supplied attesting to the fact that their product conforms to the supply specification. (3) Component parts are covered by other M3XXX Specifications. (4) The studs, nuts and washers are necessary, at least in theory, only for holding the insulation panels in place until the mastic cures, so the base material does not need to be approved in accordance with LR s procedures.
5 (5) Stainless steel supplied from LR approved works. Batch testing is to comply with the relevant GTT specification. (6) Forged components are to be manufactured in a works approved in accordance with LR s Material and Qualification Procedures for Ships Book E. (7) The base material for coupler rods and setting plates is to be manufactured in a works approved in accordance with LR s Material and Qualification Procedures for Ships Book C. (8) Weld procedure to be qualified in advance to LR's satisfaction. (9) Appraisal by LR Technical Support office following pre-production testing not required. Initial factory acceptance may be undertaken by the attending Surveyor. (10) Surveyor attendance not required if primer testing has already been witnessed in conjunction with load bearing mastic testing. (11) To be available to the Surveyors on request. (12) See and below. (13) General Approval required only if the material/component is to be used on Mk III and systems. (14) Invar supplied from LR approved works. Batch testing is to comply with the relevant GTT specification. (15) Invar (raw material) supplied from LR approved works compliant with GTT specification M3028. (16) Stainless steel (raw material) supplied from LR approved works compliant with the relevant GTT specifications. 3.2 It should be noted that there are no GTT specifications for wedge stiffening for Mk III and primary barrier corrugations, invar tubes and other prefabricated invar components, coupler sockets (forged), and coupler rods and setting plates for, but full details (materials and dimensions) are shown on the Building Principles and other approved drawings. Invar tubes and other major prefabricated invar components are to be inspected by attending Lloyd s Register surveyors during fabrication. 3.3 The manufacturers of all materials/components are expected to operate a documented quality control system which is to be made available to the attending LR Surveyors for review. The plywood manufacturers, plywood cleat manufacturers, densified wood laminate manufacturers, insulation panel manufacturers and insulation box manufacturers will be expected to submit their quality control documentation in advance of the General Approval for review by the attending LR Surveyors, who may in turn consult with the Southampton TSO/Ship Structures or other applicable Technical Support office when considered necessary, at their discretion. 3.4 The submission of data sheets which are not supported by actual test results carried out as described in 4.2 below will not be accepted. 3.5 Following satisfactory review of test reports, a General Approval certificate will be issued and the accompanying letter will state that the material/component is approved for use in the containment system, as detailed in 4. below. 4. General Approval 4.1 The approval of a material/component will allow the issuance of a General Approval Certificate for the material/component to a manufacturer which will be valid for a period of 5 years. This certificate will be restricted to the manufacture of material/component at the identified works and production line (where applicable) for the production process applied at the time of approval in accordance with a specified GTT M3XXX Specifications and revision number. 4.2 The General Approval consists of testing the material/component by either of the following means: Testing in a nationally accredited laboratory independent from manufacturer, shipyard and GTT does not require witnessing by an attending LR Surveyor Testing at the laboratory of the manufacturer, shipyard, GTT, or other laboratory which is not nationally accredited requires witnessing by an attending LR Surveyor For plywood, plywood cleat, and densified wood laminate production, the attending LR Surveyor is required to witness both the General Approval testing and also the pre-production run from which the plywood test samples are selected. This is a suitable time for the attending LR Surveyor to see the QA/QC procedures in operation as specified in 3.3 above For complete insulation panels and insulation boxes, General Approval consists of pre-production testing of the panels and boxes which requires witnessing by
6 an attending LR Surveyor. This is a suitable time for the attending Surveyor to see the QA/QC procedures in operation as specified in 3.3 above. 4.3 If either the GTT reference documentation mentioned in Table 1 above is altered to a later version, or if the product changes in design or composition, then the General Approval Certificate becomes invalid. In such a case, the General Approval Certificate will be re-issued if the changes are considered minor and not affecting the product properties, otherwise further testing will be required at the discretion of the relevant LR Technical Support office. 4.4 A manufacturer holding a current General Approval Certificate may request an additional grade of a similar material/component to be approved, for instance an additional thickness or type of plywood. After the required testing is completed, this may be covered by inclusion on the current Certificate, or by issuing a separate certificate for the additional grade, at the manufacturer s choice. 4.5 For the renewal of a General Approval Certificate, an application should be made by the manufacturer to the relevant LR Technical Support office via the local LR office. The application will be processed with consideration of previous records and any circumstances which relate to the manufacturer in question at the time of application. The manufacturer must provide a statement confirming that the sources of the raw materials and/or components, manufacturing procedures, QA/QC procedures and place of manufacturing have not changed during the period of validity of the certificate. If so, renewal of the General Approval Certificate will be granted. The date of expiry of the renewed General Approval Certificate will be no later than 10 years after the date of commencement of the Certificate it replaces. 4.6 Every 10 years after the issuance of the first certificate or last full set of testing, whichever comes earlier, full re-testing of the product will be required in order to extend the General Approval. The extended General Approval will be valid for 5 years, with renewal available for a further 5 years, as described above. 4.7 The reasons for any failure of supplied batches of material should be fed back to the relevant LR Technical Support office. Any problems / issues found during installation on board related to the quality of supplied material should be fed back similarly. 5. Material Acceptance 5.1 Materials/components produced by manufacturers which do not hold a General Approval Certificate issued by LR should not be accepted. This is because the composition of the containment system must be fully to LR s satisfaction as failure in the system components could have severe consequences for the safety of the vessel. 5.2 Notwithstanding the above, if small quantities of particular materials are requested to be accepted with certification from another Society, the advice of the relevant LR Technical Support office should be sought. 5.3 Certificates issued against the superseded MH and M specifications for the superseded External Document specifications, or the older superseded revisions of the M3XXX specifications will be replaced on application from the manufacturer, by new certificates with the same expiry date against the applicable updated M3XXX Specifications provided any additional tests required by the M3XXX specification taking account of any LR comments on that specification, are carried out with satisfactory results. Requests for this to be done should be made to the local LR office. A fee will be required for this service. 6. Application for Approval and Fees 6.1 A manufacturer applying for General Approval of a material/component covered by this scheme, or for renewal of an existing General Approval, should contact the local LR office with information clearly categorised as follows: Manufacturer s name, place of manufacture, production line (where applicable), and address for correspondence.
7 Name of the material/component. GTT material specification (M3XXX) against which approval is sought. The name(s) and addresses of the laboratories where the tests will be carried out. Confirmation of national accreditation of laboratories (to permit tests to go ahead without LR attendance). Any other information which the manufacturer would like to be taken into account. M3XXX specifications do not need to be submitted to the relevant Lloyd s Register (LR) Technical Support office except where they are a later version than that indicated. 6.2 Approval will only be granted to manufacturers (i.e. companies which make the product from raw materials and/or components of the product), not to stockholders, agents, trading companies or others parties who have not manufactured the product. 6.3 The local LR office will make a quotation to the manufacturer taking account of attendance at the manufacturer to witness the production of samples prior to testing, attendance during tests, and review of test reports by the relevant LR Technical Support office, where applicable/to the extent required, as described in this procedure. Revision history (JRA/DB) General Update after incorporating the Mark V specifications (JRA/DB) General Update based on previous revision on (AJM) Updated for revised GTT materials specifications, introduction of the Gen List, clarification of the expiry date of renewal certificates, information required for approval application, exclusion of nonmanufacturers, inclusion of latest LR logo and abbreviated liability clause, and general editorial revision including new Procedure title (SN) Update on revised specifications and typo errors correction (AJM/SN) General Update based on previous revision on (AJM/JD) based on earlier procedures from 2004, last revised (LEE). Lloyd s Register and variants of it are trading names of Lloyd s Register Group Limited, its subsidiaries and affiliates. Lloyd s Register EMEA (Reg. no R) is an Industrial and Provident Society registered in England and Wales. Registered office: 71 Fenchurch Street, London, EC3M 4BS, UK. A member of the Lloyd s Register group. Lloyd s Register Group Limited, its affiliates and subsidiaries and their respective officers, employees or agents are, individually and collectively, referred to in this clause as the Lloyd s Register'. Lloyd s Register assumes no responsibility and shall not be liable to any person for any loss, damage or expense caused by reliance on the information or advice in this document or howsoever provided, unless that person has signed a contract with the relevant Lloyd s Register entity for the provision of this information or advice and in that case any responsibility or liability is exclusively on the terms and conditions set out in that contract. Working together for a safer world
ShipRight Notice for. Linked Supporting Services Anti-Corrosion System Notation, July Issue date: September 2014
ShipRight Notice for Linked Supporting Services Anti-Corrosion System Notation, July 2012 The status of this Rule set is amended as shown and is now to be read in conjunction with this and prior Notices.
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of Works for the Manufacture of Fusion Welded Pressure Vessels Revision 4, July 2015 Page 1 of 17 Lloyd s Register Group Limited, its subsidiaries
More informationEC TYPE EXAMINATION (MODULE B) CERTIFICATE
EC TYPE EXAMINATION (MODULE B) CERTIFICATE This is to certify that: LLOYD'S REGISTER VERIFICATION LIMITED (LRV), designated as a notified body under the terms of the Merchant Shipping (Marine Equipment)
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of Fibre Reinforcements Revision 1, December 2013 Material and Qualification Procedures for Ships Lloyd s Register Group Limited, its subsidiaries
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of a Works for the Manufacture of Non-heat treated ERW Steel Pipes Revision 2, Sept 2014 Lloyd s Register Group Limited, its subsidiaries and affiliates
More informationCERTIFICATE OF FIRE APPROVAL
LR427.203.2 CERTIFICATE OF FIRE APPROVAL This is to certify that The product detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations and with the International
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of a Works for the Manufacture of Steel Forgings for Semi- Built and Continuous Grain Flow Crankshafts Revision 3, January 2015 Page 1 of 14 Lloyd
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval Procedure for Laboratories Engaged in Testing of Coating Systems in Accordance with IACS Z17 and IMO MSC.215(82) and/or IMO MSC.288(87). Revision
More informationThe Technical & Practical challenges of FLNG
SUT Evening Technical Meeting: On the Fringes of FLNG, Perth 19/08/2015 Jeff Baker Energy Compliance Technical Manager, Australasia Working together for a safer world Agenda Introduction Acknowledgement
More informationCERTIFICATE OF FIRE APPROVAL
Examined Office LR427..206.09 CERTIFICATE OF FIRE APPROVAL This is to certify that The product detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations
More informationIntroduction to KC-1 CARGO CONTAINMENT SYSTEM
Introduction to KC-1 CARGO CONTAINMENT SYSTEM 2016-10-20 Senior Researcher Jun-ho, Seong CONTENTS 1. Introduction II. Design Concept of KC-1 III. Summary CONTENTS 1. Introduction II. Design Concept of
More informationEC TYPE EXAMINATION (MODULE B) CERTIFICATE
LR427.203.2 EC TYPE EXAMINATION (MODULE B) CERTIFICATE This is to certify that: LLOYD'S REGISTER VERIFICATION LIMITED (LRV), designated as a notified body under the terms of the Merchant Shipping (Marine
More informationSTRUCTURAL STEEL FRAMING
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 SUMMARY A. Section includes 1. Structural steel framing 2. Structural steel framing required for support and framing of rooftop mechanical
More informationShipRight Design and Construction
ShipRight Design and Construction Additional Design Procedures Assessment of Steel Hatch Covers Using Finite Element Analysis January 2018 Working together for a safer world Document History Document Date:
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of a Foundry for the Manufacture of Steel Castings Revision 3, January 2015 Lloyd s Register Group Limited, its subsidiaries and affiliates and
More informationLR SOFTWARE CONFORMITY ASSESSMENT SYSTEM. Assessment Module GENPMS Software Products for Planned Maintenance Schemes
LR SOFTWARE CONFORMITY ASSESSMENT SYSTEM Assessment Module GENPMS Software Products for Planned Maintenance Schemes 2006 Lloyd's Register, its affiliates and subsidiaries and their respective officers,
More informationRules for the Manufacture, Testing and Certification of Materials
Rules for the Manufacture, Testing and Certification of Materials July 2013 A guide to the Rules and published requirements Rules for the Manufacture, Testing and Certification of Materials Introduction
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of a Works for the Manufacture of Chain Cable for ships Revision 2, April 2015 Page 1 of 19 Lloyd s Register Group Limited, its subsidiaries and
More informationSPECIFICATIONS - DETAILED PROVISIONS Section Stainless Steel Sluice Gates C O N T E N T S
SPECIFICATIONS - DETAILED PROVISIONS Section 11294 - Stainless Steel Sluice Gates C O N T E N T S PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 DEFINITIONS... 1 1.04 DESIGN REQUIREMENTS...
More informationProperties Of Membrane Tanks For Transportation Of LNG Cargo On Ships
1 Properties Of Membrane Tanks For Transportation Of LNG Cargo On Ships LNG as fuel is now a proven and available solution for the shipping industry. While conventional oil-based fuels remain the main
More informationALUMINIUM AND ARTICLES THEREOF
CHAPTER 76 ALUMINIUM AND ARTICLES THEREOF Note 1. In this chapter, the following expressions have the meanings hereby assigned to them: (a) Bars and rods: Rolled, extruded, drawn or forged products, not
More informationApplication for a recommendation on the use of membrane tanks for transport of liquefied natural gas on the tank vessel Argos-GL
Economic Commission for Europe Inland Transport Committee Working Party on the Transport of Dangerous Goods Joint Meeting of Experts on the Regulations annexed to the European Agreement concerning the
More informationMaterials and Qualification Procedures for Ships
Materials and Qualification Procedures for Ships Approval of a Foundry for the Manufacture of Stainless Steel Castings including Propellers Revision 2, January 2015 Lloyd s Register Group Limited, its
More informationCERTIFICATE OF FIRE APPROVAL
LR427.203.2 CERTIFICATE OF FIRE APPROVAL This is to certify that The product detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations and with the International
More informationUnderstanding EN 10204:2004 Type 3.2 Certification. Working together for a safer world
Understanding EN 10204:2004 Type 3.2 Certification Working together for a safer world EN 10204:2004 Type 3.2 Certification INTRODUCTION History and Development of the Standard Applicability; Definitions
More informationDivision 11 - Equipment Section 11401
PART 1 - GENERAL 1.1 GENERAL A. Division 1 General Requirements applies and becomes a part of this Section of the Specification as fully as if repeated herein. B. Items of equipment which are included
More informationSheet Metal Flashing and Trim
University of New Hampshire University of New Hampshire Scholars' Repository Division 07 Thermal and Moisture Protection Chapter 5 Technical Construction and Renovation Standards 1-25-2013 076200 - Sheet
More informationCertificate of Conformity of Factory Production Control
Certificate of Conformity of Factory Production Control This certificate is issued to: Weldon Road, Corby, Northants, NN17 5UE Cleveland, TS25 2EG In compliance with Regulation 305/2011/EU of the European
More informationChapter 73. Articles of iron or steel
Chapter 73 Articles of iron or steel Notes. 1.- In this Chapter the expression cast iron applies to products obtained by casting in which iron predominates by weight over each of the other elements and
More informationQualification scheme for welders of hull structural steels
(Sept 2016) Qualification scheme for welders of hull structural steels 1. Scope 1.1 This document gives requirements for a qualification scheme for welders intended to be engaged in the fusion welding
More informationSECTION C. Water Infiltration: Provide manufactured cupolas and dormers that do not allow water infiltration to cupola and dormer interiors.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Manufactured exterior cupolas. 2. Manufactured dormers. 3. Historical locomotive weather Vane. 1.2 PERFORMANCE REQUIREMENTS A. General:
More informationCode Compliance Research Report CCRR-0257
Code Compliance Research Report CCRR-0257 Issued: 12-21-2016 Renewal Due: 12-21-2018 Revised: 12-20-2017. DIVISION: 05 50 00 Metal Fabrications Section: 05 52 00 Metal Railings REPORT HOLDER: VINYLAST,
More informationContents EN :2008+A1:2011 (E) Page
Contents Page Foreword... 9 Introduction... 10 1 Scope... 11 2 Normative references... 12 2.1 General... 12 2.2 Constituent products... 12 2.2.1 Steels... 12 2.2.2 Steel castings... 14 2.2.3 Welding consumables...
More informationADVANCE METAL INDUSTRIES L.L.C.
ADVANCE METAL INDUSTRIES L.L.C. Copyright reserved for ADVANCE METAL ''Due to continuos progress and product improvement, ADVANCE METAL reserves the right to make changes without notice'' DISCLAIMER OF
More informationRight Additional Design Procedures
ShipRight Design and construction Additional Design Procedures Assessment of Steel Hatch Covers Using Finite Element Analysis July 2007 ABCD Lloyd s Register Marine Business Stream 71 Fenchurch Street
More informationCERTIFICATION SCHEME FOR TYPE APPROVAL OF PRODUCTS
CERTIFICATION SCHEME FOR TYPE APPROVAL OF PRODUCTS 1. Introduction 1.1 Scheme for type approval of products of Indian Register of Shipping (IRS) is an impartial certification system based on a design review
More informationSTANDARD SPECIFICATION FOR ALUMINUM FRAMING FOR RAILROAD PASSENGER SHELTERS
SOUTHEASTERN PENNSYLVANIA TRANSPORTATION AUTHORITY 1234 MARKET STREET, PHILADELPHIA, PA 19107 STANDARD SPECIFICATION FOR ALUMINUM FRAMING FOR RAILROAD PASSENGER SHELTERS REVISION DATE SPECIFICATION # F-S-304_
More informationCERTIFICATE OF FIRE APPROVAL
LR2009.030. CERTIFICATE OF FIRE APPROVAL This is to certify that The product(s) detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations for use on offshore
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More information50948-RHN Putney. Friday, 15 December This document includes: Code Section Revision Dated
50948-RHN Putney Friday, 15 December 2017 This document includes: Code Section Revision Dated Z11 Purpose made metalwork 1 Table of Contents Title Z11 Purpose made metalwork Page 3 Z11 Purpose made metalwork
More informationCode Compliance Research Report CCRR-0238
Code Compliance Research Report CCRR-0238 Issue Date: 11-09-2016 Revision Date: 11-29-2018 Renewal Date: 11-09-2019 DIVISION: 05 00 00 METALS Section: 05 52 00 Metal Railings CPG Building Products LLC
More informationCERTIFICATE OF FIRE APPROVAL
LR427.203.2 CERTIFICATE OF FIRE APPROVAL This is to certify that The product detailed below will be accepted for compliance with the applicable Lloyd s Register Rules and Regulations and with the International
More informationStandard Installation Fire Damper Models: 119, 119(F), 119(SS), D19
Standard Installation Fire Damper Models: 119, 119(F), 119(SS), D19 Page 1 or 8 APPLICATION This fi re damper is intended to restrict the passage of fl ame. The standard installation requires that the
More informationQualification scheme for welders of aluminium alloys
(March 2009) Qualification scheme for welders of aluminium alloys 1. Scope 1.1 This document provides guidance for a qualification scheme for welders intended to be engaged in welding of aluminium alloys
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationSECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM
Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING
More informationInspection and Verification Requirements. Test Procedures for Qualification of Corrosion Resistant Steel for Cargo Tanks in Crude Oil Tankers
(Jan 2013) For Application of Regulation 3-11, Part A-1, Chapter II-1 of the SOLAS Convention (Corrosion Protection of Cargo Oil Tanks of Crude Oil Tankers), adopted by Resolution M.289 (87) The Performance
More informationRATE OF DUTY UNIT(S) DESCRIPTION OF GOODS
73.01 Sheet piling of iron or steel, whether or not drilled, punched or made from assembled elements; welded angles, shapes and sections, of iron or steel. 7301.10.00 Sheet piling 5% kg 7301.20.00 Angles,
More informationDIVISION 5 METALS SECTION STRUCTURAL STEEL
DIVISION 5 METALS SECTION 05 12 00 PART 1 GENERAL 1.01 SUMMARY A. Section Includes: All labor and materials required to furnish and install the structural steel shown on the Drawings and required by these
More informationCode Compliance Research Report CCRR-0225
Code Compliance Research Report CCRR-0225 Issue Date: 02-04-2016 Revision Date: 05-30-2018 Renewal Date: 02-10-2019 DIVISION: 09 00 00 - FINISHES Section: 09 69 00 Access Flooring REPORT HOLDER: Global
More informationMATERIAL SPECIFICATION FOR DECK JOINT ASSEMBLIES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 1210 NOVEMBER 2016 1210.01 SCOPE 1210.02 REFERENCES 1210.03 DEFINITIONS MATERIAL SPECIFICATION FOR DECK JOINT ASSEMBLIES TABLE OF CONTENTS 1210.04
More informationStorage & loading on site SOFREGAZ
Large Cryogenic above ground LNG Tank Full Containment (9% inner wall + Pre-stressed concrete outer wall) Typical Construction Sequence March 4 th 2011 Storage & loading on site Storage & loading on site
More informationA. Product Data: Identify thermal conductivity, thickness, and jackets (both factory and field applied, if any), for each type of product indicated.
SECTION 23 07 13 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationTRESPA WALL CLADDING SYSTEMS SYSTEM 700 ALUMINIUM SUB-FRAME SYSTEM
Trespa International B.V. P O Box 110 6000 AC Weert The Netherlands Tel: 00 31 0495 458358 Fax: 00 31 0495 458570 e-mail: infonederland@trespa.com website: www.trespa.com APPROVAL INSPECTION TESTING CERTIFICATION
More informationSpecial Provision No. 915S03 December References, Materials, Construction, and Quality Assurance for Sign Support Structures
STEEL MONOTUBE OVERHEAD SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN NON-BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. CANTILEVER STATIC SIGN
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationElectrical Services Standard Specification Cable Tray Installation. May For ROYAL HOLLOWAY UNIVERSITY OF LONDON
Electrical Services Standard Specification 4.0 - Cable Tray Installation May 2010 For ROYAL HOLLOWAY UNIVERSITY OF LONDON Prepared For The Estates Division By: Hulley & Kirkwood Consulting Engineers Ltd
More informationCERTIFICATE OF APPROVAL No CF 5073 LEMINAR AIR CONDITIONING INDUSTRIES L.L.C.
CERTIFICATE OF APPROVAL No CF 5073 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of PO Box 33539, Dubai,
More informationCode Compliance Research Report CCRR-0238
Code Compliance Research Report CCRR-0238 Issued: 11-09-2016 Renewal Due: 11-09-2018 Revised: 11-10-2017 DIVISION: 05 00 00 METALS Section: 05 52 00 Metal Railings CPG Building Products LLC 894 Prairie
More informationHull Survey for New Construction
(July 2006) (Rev.1 Mar 2007) (Corr.1 Oct 2007) (Rev.2 Apr 2009) (Corr.1 August 2012) Hull Survey for New Construction 1. Scope The scope of this UR includes the following main activities: 1.1 Examination
More informationRATING: Consult factory for availability Consult factory for availability
DYNAMIC FIRE DAMPER MODELS: 75A-DY (1-1/2 HR rating) APPLICATION The model 75A-DY is constructed with standard constructiongalvanized steel. 75A-DY is 1-1/2 hour UL rated dynamic damper for use in HVAC
More informationCode Compliance Research Report CCRR-0225
Code Compliance Research Report CCRR-0225 Issue Date: 03-01-2017 Renewal Date: 02-10-2018 DIVISION: 09 00 00 FINISHES Section: 09 69 00 Access Flooring Haworth Inc. One Haworth Center Holland, MI 49423
More informationSpecification for Fabrication of Steelwork for Pole Structures
Ergon Energy Corporation Limited Specification for Fabrication of Steelwork for Pole Structures This material is made available on the basis that it may be necessary for a Registered Professional Engineer
More informationSECTION WALL AND DOOR PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to
More informationD D TYPE A1, A2 & B MICHIGAN DEPARTMENT OF TRANSPORTATION 5-40 CONNECTION. L4" x 4" x 3/8" Brace. C8 x 4.25 Strut. WT9 x 17.5.
Sign length minus Adjust to avoid interference with sign legend A Deck fascia A 6" Equal Equal 6" Sign length (L) varies 6 to 12 PLAN 0 CONNECTION (DECK FASCIA) Angle connection assembly F Face of concrete
More informationSECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 260548 - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Isolation pads. 2. Spring isolators. 3. Restrained spring isolators. 4. Channel
More informationA. This Section includes duct and plenum insulation; accessories and attachments; and sealing compounds.
SECTION 230713 DUCT INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSpecification for the Fabrication of Tower Structures
Ergon Energy Corporation Limited Specification for the Fabrication of Tower Structures This material is made available on the basis that it may be necessary for a Registered Professional Engineer of Queensland
More informationEC TYPE EXAMINATION (MODULE B) CERTIFICATE
LR427.203.2 EC TYPE EXAMINATION (MODULE B) CERTIFICATE This is to certify that: LLOYD'S REGISTER VERIFICATION LIMITED (LRV), specified as a notified body under the terms of The Merchant Shipping (Marine
More informationEC TYPE EXAMINATION (MODULE B) CERTIFICATE
EC TYPE EXAMINATION (MODULE B) CERTIFICATE This is to certify that: LLOYD'S REGISTER VERIFICATION LIMITED (LRV), designated as a notified body under the terms of the Merchant Shipping (Marine Equipment)
More informationSECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN
SECTION 08350 MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More information1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.
PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 1850 APRIL 2018 (Formerly OPSS 1850, April 2013) Note: The PROV published in April 2018 replaces OPSS 1850 COMMON, April 2013 with no technical content
More information05510: TAPERED STEEL TROLLEY POLES AND ACCESSORIES
PART 1 GENERAL 1.01 DESCRIPTION A. The Vendor shall fabricate, furnish, test and deliver tapered steel trolley poles, including base plates, reinforced hand holes, anchor bolts, nuts and washers, and accessories
More informationLLOYD INDUSTRIES INC. DAMPER INSTALLATION INSTRUCTIONS
Installation and Maintenance Instructions 1-1/2 Hour Rated, UL Classified model 75 fire dampers For use in fire barriers with ratings of less than 3 hours INSPECTION 1. Inspect for shipping damage. 2.
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB #
SECTION 26 0529 - HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationBBA 001 Documents included under the scope of BBA s ISO UKAS accreditation
BBA 001 Documents included under the scope of BBA s ISO 17065 UKAS accreditation Product Standard Building Systems and Kits BBA Technical Specification 001 Ceiling Products BBA Technical Specification
More informationEC TYPE EXAMINATION (MODULE B) CERTIFICATE
LR427.203.2 EC TYPE EXAMINATION (MODULE B) CERTIFICATE This is to certify that: LLOYD'S REGISTER VERIFICATION LIMITED (LRV), specified as a notified body under the terms of The Merchant Shipping (Marine
More informationSTATEMENT OF SPECIAL INSPECTION FORM
Project Title: Permit #: Project Address: STATEMENT OF SPECIAL INSPECTION FORM This Statement of Special Inspections is submitted in fulfillment of the requirements of CBC Sections 1704 and 1705. Special
More informationITW INSULATION SYSTEMS
ITW INSULATION SYSTEMS 1SCOPE TRYMER RIGID POLYISOCYANURATE INSULATION IN LIQUEFIED NATURAL GAS APPLICATIONS (-260 F) 1.1 This guideline covers the installation of Trymer* Rigid Polyisocyanurate Insulation
More informationSECTION METAL EQUIPMENT LOCKERS
SECTION 10 51 13 - METAL EQUIPMENT LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationIRON AND STEEL PRODUCTS
Announcement: Please be informed that the Fast Track Clearance facilities will expire on 21 st August 2013. In addition, with effective from 22 nd August 2013, all Certificate of Approval applications
More informationLaboratory Accreditation Programmes
Laboratory Address PO Box 6178, Upper Riccarton, Christchurch, 8442 52 Hayton Road, Sockburn, Christchurch, 8042 Telephone 03 343-3530 URL Authorised Representative Client No. 153 Programme Accreditation
More information1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationC. Preparation and submission of complete engineered shop drawings for approval. E. Coordination with other affected work, trades and inspections.
SECTION 11 61 13 ARIA ACOUSTICAL SHELL PART 1-GENERAL 1.1 SUMMARY A. This specification section includes the engineering, fabrication, furnishing, delivery and installation of new acoustical shell system
More informationSTATE UNIVERSITY CONSTRUCTION FUND. UNIVERSITY CON DIRECTIVE 5-1 Issue date: October 2014
STATE STRUCTION FUND DIRECTIVE 5-1 Issue date: October 2014 STRUCTURAL STEEL 1. General: It is the Fund's policy that the design of the structural steel is the prime responsibility of the project's Structural
More informationRefurbishment site guidance for solid-walled houses windows and doors
GOOD PRACTICE GUIDE 295 Refurbishment site guidance for solid-walled houses windows and doors What energy savings to aim for Key points to consider Energy savings and SAP ratings Environmental considerations
More informationCommission No Section
Commission No. 1511 Section 05120-1 PART ONE - GENERAL 1.1 DESCRIPTION A. Work Included: Structural steel and grout. Furnish, fabricate, mark for erection identification, pack, crate, or otherwise properly
More informationOKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISIONS FOR BUY AMERICA
106-5(a-f) 09 OKLAHOMA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISIONS FOR BUY AMERICA These Special Provisions amend, revise, and where in conflict, supersede applicable sections of the 2009 Standard
More informationTechnical Specification for Steel Forged Fittings
Ergon Energy Corporation Limited Technical Specification for Steel Forged Fittings ETS 01-01-01 ETS 01-01-01 Ver 2 Contents 1. Purpose and Scope... 1 2. References... 1 2.1 Applicable Standards... 1 3.
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationSECTION COLD-FORMED METAL TRUSSES
SECTION 054400 COLD-FORMED METAL TRUSSES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationSECTION HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS
SECTION 26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and
More informationMarine & Offshore Fire Divisions
Marine & Offshore Fire Divisions bulkhead & deck systems U-FW/GMM EN Rev: 2 Sept 18 Contents Page No. Introduction Installation Surface Coverings - General Principles - Anchors - System Repair and Maintenance
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.MUNI 1850 NOVEMBER 2018 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationSECTION BLAST RESISTANT WINDOWS
SECTION 08 56 53 BLAST RESISTANT WINDOWS SPEC WRITER NOTE: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. See VA Physical Security Design Manual for security
More informationSection includes plate heat transfer panels as detailed in drawings listed in Section 1.1 Related Documents.
SPEC-FTS-205 Plate Heat Transfer Panels 1. GENERAL 1.1 RELATED DOCUMENTS A. DKIST-RFQ-205-DSH-123-4-Plate Heat Transfer Panels Datasheet B. DKIST-DWG-E-6.7.11-2001_5 Zones C. DKIST-DWG-E-6.7.11-2002_5
More informationC. Preparation and submission of complete engineered shop drawings for approval. E. Coordination with other affected work, trades and inspections.
SECTION 11 61 13 BRAVADO ACOUSTICAL SHELL PART 1-GENERAL 1.1 SUMMARY A. This specification section includes the engineering, fabrication, furnishing, delivery and installation of new acoustical shell system
More informationCode Compliance Research Report CCRR-0228
Code Compliance Research Report CCRR-0228 Issue Date: 05-09-2017 Renewal Date: 05-11-2018 Revision Date: 06-23-2017 DIVISION: 07 00 00 THERMAL AND MOISTURE PROTECTION Section: 07 40 00 Roofing and Siding
More information