SECTION ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL
|
|
- Arnold Goodwin
- 6 years ago
- Views:
Transcription
1 SECTION ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions and applicable portions of Division 1 - General Requirements. B. The work consists of all labor, material and equipment necessary and required to complete all acoustical panel ceilings as shown on the drawings and specified herein RELATED WORK SPECIFIED ELSEWHERE: A. Mechanical Fixtures in Acoustical Panel Ceilings: Division 15. B. Electrical Fixtures in Acoustical Panel Ceilings: Division SUBMITTALS A. Product Data: Manufacturer s product specifications and installation instructions for each acoustical ceiling material required, and for each suspension system, including certified laboratory test reports and other data as required to show compliance with these specifications. 1. Include manufacturer s recommendations for cleaning and refinishing acoustical units, including precautions against materials and methods which may be detrimental to finishes and acoustical performances. B. Samples: Set of 12 inches square samples for each acoustical unit required, showing full range of exposed color and texture to be expected in completed work. 1. Set of 12 inches long samples of each exposed runner and molding. C. Single Source Responsibility: Obtain each type of acoustical ceiling unit and each type of suspension system from a single source with resources to provide products of consistent quality in appearance and physical properties without delaying progress of the work. D. Coordination of Work: Coordinate layout and installation of acoustical ceiling units and suspension system components with other construction that penetrates ceilings or is supported by them, including light fixtures, HVAC equipment, fire suppression systems components, if any, and partition systems, if any JOB CONDITIONS A. Space Enclosure: Do not install interior acoustical ceilings until wet-work in space is completed and nominally dry, and until work above ceilings completed and until ambient conditions of temperature and humidity will be continuously maintained at values near those indicated for final occupancy DELIVERY, STORAGE AND HANDLING A. Deliver acoustical ceiling units to project site in original, unopened packages and store them in a fully enclosed space where they will be protected against damage from moisture, direct sunlight, surface contamination and other causes. B. Before installing acoustical ceiling units, permit them to reach room temperature and a stabilized ACOUSTICAL PANEL CEILINGS
2 moisture content. C. Handle acoustical ceiling units carefully to avoid chipping edges or damaging units in any way EXTRA MATERIALS A. Deliver extra materials to Owner. Furnish extra materials described below that match products installed, are packaged with protective covering for storage and are identified with appropriate labels. 1. Acoustical Ceiling Units: Furnish quantity of full sized units equal to 2 percent of amount installed. 2. Exposed Suspension System Components: Furnish quantity of each exposed component equal to 2 percent of amount installed Quality Assurance A. Standards for Performance shall be as indicated except, as more rigid standards are set elsewhere in the specifications. 1. Metal Suspension Systems for Acoustical Tile and Lay-In Panel Ceilings, ASTM C635, latest edition. 2. Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels, ASTM C636, latest edition. 3. Ceiling and Interior Systems Contractors Assoc. (CISCA) The Ceiling Systems Handbook, and referenced data, latest editions. 4. Clean Rooms as designated by Illinois Department of Public Health (IDPH) and United States Department of Agriculture (USDA) shall conform with F.S. 209D, Class Building Code Requirements: a. State of Illinois NFPA and (IDPH), ASTM 255, Class A Flame spread 0-25, smoke developed b. International Building Code, 2000 (IBC), ASTM E84, Class T, flame spread 0-25, smoke developed Acoustical Panel Finish Surface: F.S. SS-S118B Class A, Type III. PART 2 - PRODUCTS 2.01 CEILING UNITS A. Acoustical Panels (ACT-1): Shall be 24 inches by 24 inches in size, 3/4 inch thick, mineral fiber panel with beveled tegular edge for installation on a 15/16 inch exposed T suspension system. Panels shall have manufacturer s standard white vinyl latex paint finish. Panels shall be: 1. Armstrong, Ultima Tegular Fine Texture 1951 with beveled tegular edge, or approved equal. B. Acoustical Panels (ACT-2): Shall be 24 inches by 24 inches in size, 3/4 inch thick, nonperforated mineral fiber panel with square cut edge for installation on a 15/16 inch exposed T suspension system. Panels shall have manufacturer s standard white vinyl faced finish. Panels shall be one of the following: 1. Armstrong, Ultima Square Lay-In Fine Texture 1910, or approved equal. ACOUSTICAL PANEL CEILINGS
3 C. Acoustical Panels (ACT-3): Shall be 24 inches by 24 inches in size, 3/4 inch thick, clean room mylar faced non-perforated panels with square edge for installation on a 15/16 inch exposed T suspension system. Panels shall be: 1. Armstrong clean room mylar square Lay-In smooth texture 1715 field unit and 1720 border unit, or approved equal. D. Acoustical Panels (ACT-4): Shall be 24 inches by 24 inches in size, 3/4 inch thick, Woodworks Vector for installation on a 15/16 inch concealed T suspension system. Panels shall be: 1. Armstrong Woodworks Vector Constants Micro- perforated Constants Cherry 6812, or approved equal. E. Acoustical Panels (ACT-5): Shall be 24 inches by 24 inches in size, 1 inch thick, Optima Open Plan for installation on a 15/16 inch exposed T system. Panels shall be: 1. Armstrong Optima open plan tegular square edge fine texture 325, or approved equal CEILING SUSPENSION MATERIALS A. General: Comply with ASTM C 635, as applicable to type of suspension system required for type of ceiling units indicated. Coordinate with other work supported by or penetrating through ceilings, including light fixtures, HVAC equipment, and partition system. B. Attachment Devices: Size for 5 times design load indicated in ASTM C 635, Table 1, Direct Hung. 1. Hanger Wires: Galvanized carbon steel, ASTM A 641, soft temper, pre-stretched, yield-stress load of at least 3 times design load, but not less than 12 gauge (0.106 ). C. Type of System: Either direct-hung or indirect-hung suspension system, at Contractor s option. 1. Carrying Channels: 1-1/2 inches steel channels, hot-rolled or cold-rolled, galvanized, not less than pounds per lineal foot. D. Acceptable Manufacturers: Shall be Armstrong or USG Interiors Inc., or Chicago Metallic Corp. All ceiling suspension systems shall have manufacturer s standard white finish. The following systems are based on Chicago Metallic Corp.: 1. Tempra 4000 System, 9/16 inch face, galvanized steel System, 15/16 inch face, galvanized steel. E. Edge Moldings: Manufacturer s standard straight edge 15/16 inch face, L-molding at all grid/wall intersections. Provide field cut narrow reveal edge at acoustical ceiling panels for 9/16 inch exposed T suspension system. F. Exposed Suspension System: Manufacturer s standard exposed runners, cross-runners and accessories, of types and profiles indicated, with exposed cross runners coped to lay flush with main runners, white baked enamel finish. G. Hold Down Clips for Non-Fire-Resistance Rated Ceilings: For interior ceilings composed of layin panels weighing less than 1 pound per square foot, provide hold down clips spaced 2 feet 0 inches o.c. on all cross-tees MISCELLANEOUS MATERIALS A. Edge Trim Molding: Metal, of types and profiles indicated, finish to match exposed suspension system members. B. Concealed Acoustical Sealant: Non-drying, non-hardening, non-skinning, non-staining, nonbleeding, gunnable sealant complying with requirement specified in Division 7 Section Joint Sealants. ACOUSTICAL PANEL CEILINGS
4 PART 3 - EXECUTION 3.01 INSPECTION A. Examine conditions under which acoustical ceiling work is to be performed and notify Contractor in writing of unsatisfactory conditions. Do not proceed with work until unsatisfactory conditions have been corrected PREPARATION A. Coordination: Furnish layouts for inserts, clips, or other supports required to be installed by other trades for support of acoustical ceilings. B. Measure each ceiling area and establish layout of acoustical units to balance border widths at opposite edges of each ceiling. Avoid use of less-than-half width units at borders, and comply with reflected ceiling plans wherever possible INSTALLATION A. General: Install materials in accordance with manufacturer s printed instructions, and to comply with governing regulations, fire-resistance rating requirements as indicated, and industry standards applicable to work. B. Install suspension system to comply with ASTM C 636, with hangers supported only from building structural members. Locate hangers near each end and space 4 feet along each carrying channel or direct-hung runner, unless otherwise indicated, leveling to tolerance of 1/8 inch in 12 feet. 1. Secure wire hangers by lopping and wire-tying, either directly to structures or to inserts, eye-screws, or other devices which are secure and appropriate for substrate, and which will not deteriorate or fail with age or elevated temperatures. C. Install edge moldings of type indicated at perimeter of acoustical ceiling area and at locations where necessary to conceal edges of acoustical units. 1. Screw- attach moldings to substrate at intervals not over 16 inches o.c. and not more than 3 inches from ends, leveling with ceiling suspension system to tolerance of 1/8 inch in 12 feet. Miter corners accurately and connect securely. 2. Sealant Bed: Apply continuous ribbon of acoustical sealant, concealed on back of vertical leg before installing moldings. D. Install acoustical panels in coordination with suspension system, with edges concealed by support of suspension member. Scribe and cut panels to fit accurately at borders and at penetrations. 1. Install hold-down clips in areas indicated, and in areas where required by governing regulations or for fire-resistance ratings; space as recommended by panel manufacturer, unless otherwise indicated or required. E. All vinyl faced, non-perforated panels shall be installed with a closed-cell sponge neoprene gasket between flanges of suspension system and panel and No. 414 hold down clips spaced 24 inches o.c. on all cross- tees. All field cut edges shall be sealed to conform with F.S. 209D, Class EXISTING CEILING SYSTEMS A. In rooms being altered and in rooms where present acoustical ceilings shall be extended or altered, use materials to match and by same manufacturer. If same material is not available, submit, for review, samples of available material which most nearly match, in style, quality and appearance ACOUSTICAL PANEL CEILINGS
5 3.05 ADJUST AND CLEAN A. Clean exposes surfaces of acoustical ceilings, including trim, edge moldings, and suspension members; comply with manufacturer s instructions for cleaning and touch-up of minor finish damage. Remove and replace work which cannot be successfully cleaned and repaired to permanently eliminate evidence of damage. END OF SECTION ACOUSTICAL PANEL CEILINGS
6
A. This Section includes acoustical panel ceilings installed with exposed suspension systems.
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationConstruction Standards PAGE
Construction Standards PAGE 095113-1 SECTION 095113 - PART 1 - GENERAL 1.1 M.S.U. ISSUES 1. It the intent of MSU that all joint sealants used on its projects will comply with LEED NC 3 Credit Requirements
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 095113 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationA. Product Data: Submit manufacturer's descriptive literature, and recommendations and instructions for installation.
SECTION 09512 - ACOUSTICAL TILECEILINGS (ACT-01 and ACT-02) PART 1 - GENERAL 1.01 SUMMARY A. Section includes ceilings consisting of acoustical panels and exposed suspension systems. This ceiling system
More informationStore No MAY 13 Addendum No. 1 SECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. AC: Articulation
More informationA. This Section includes ceilings consisting of acoustical panels and exposed suspension systems.
SECTION 09 51 13 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More information1. This addendum contains the specifications for Acoustical Ceilings: public areas Lobby, Breakfast Room, etc. and not used on all doors.
ADDENDUM NO. 4 PROJECT NAME: GENERAL CONTRACTOR: ADDRESS: Holiday Inn Express - York NGC Group Inc. 3830 South 6 th Street Lincoln, NE 68502 DATE OF ISSUANCE: May 10, 2013 DATE OF BID OPENING: Tuesday,
More informationSECTION ACOUSTICAL PANEL CEILINGS. A. Section includes acoustical panels and exposed suspension systems for ceilings.
SECTION 09 51 13 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section includes acoustical panels and exposed suspension systems for ceilings. 1.2 SUBMITTALS A. Product Data: For each type
More informationGeometrik Manufacturing Inc.
PRODUCT: GEOSQUARE WOOD TILES Page 1 PART I GENERAL 1.1 SECTION INCLUDES 1. GeoSquare wood [acoustical] ceiling tiles. 2. Coordination with other trades that have parts attached to, penetrate through or
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO. 2700
SECTION 09 5113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION ACOUSTICAL CEILINGS
SECTION 09511 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Acoustical ceiling panels. B. Exposed grid suspension system. C. Wire hangers, fasteners, main runners, cross tees, and wall angle
More informationStudent Services & Classroom Addition
SECTION 095133 - ACOUSTICAL METAL PAN CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION LINEAR METAL CEILINGS
SECTION 09 5423 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More information1. Acoustical panels. 2. Exposed suspension systems for ceilings. 3. Wire hangers, fasteners, main runners, cross tees, and wall angle moldings.
SECTION 095113 - ACOUSTICAL PANEL WALLS & CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSection GYPSUM DRYWALL
Section 09250 GYPSUM DRYWALL 1.00 GENERAL: A. Gypsum Association Specification GA216 and manufacturer's instruction (whichever is more stringent). 2.00 DRYWALL MATERIALS: A. Exposed Gypsum Board: ASTM
More informationOCALA INTERNATIONAL AIRPORT MBI PN: GENERAL AVIATION TERMINAL JANUARY 16, 2018 ADDENDUM-ISSUE
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationA. ASTM C635, Standard Specifications for Metal Suspension Systems. B. ASTM C636, Recommended Practice for Installation of Metal Suspension System
SECTION 09510 / 09 51 00 USG TRUE WOOD LINEAR PANELS Product Specification WOOD CEILING PANELS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General
More information***************************************************************************************************************
09510 ACOUSTICAL CEILINGS SPECIFIER: CSI MasterFormat 2004 number 09 51 00 PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310
More informationSECTION ACOUSTICAL TILE. *(Filed Sub-Bid Required) 1.00 TIME, MANNER AND REQUIREMENTS FOR SUBMITTING SUB-BIDS
SECTION 090003 *(Filed Sub-Bid Required) PART 1 GENERAL 1.00 TIME, MANNER AND REQUIREMENTS FOR SUBMITTING SUB-BIDS A. Sub-bids shall be submitted in accordance with provisions of the General Laws (Ter.
More informationA. ASTM C635, Standard Specifications for Metal Suspension Systems. B. ASTM C636, Recommended Practice for Installation of Metal Suspension System
SECTION 09510 / 09 51 00 USG TRUE WOOD LAY IN AND ACCESSIBLE REVEAL Product Specification WOOD CEILING PANELS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract,
More informationSECTION (09512) - ACOUSTICAL TILE CEILINGS
SECTION 09 51 23 (09512) - ACOUSTICAL TILE CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Suspended Metal Grid Systems Complete With Wall Trim 2. Suspended Fiberglass Grid Systems Complete
More informationUniSpec II - Store Planning
UniSpec II - Store Planning 072613 SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Suspended metal grid ceiling system. 2. Acoustical panels. 3. Perimeter
More informationGeometrik Manufacturing Inc.
PRODUCT: GEO SYSTEM Page 1 PART I GENERAL 1.1 SECTION INCLUDES 1. Linear Acoustical Wood Ceiling System including suspension hardware by Geometrik Manufacturing Inc. 2. Coordination with other trades that
More informationSECTION ACOUSTICAL CEILINGS (CEMENTITIOUS WOOD FIBER CEILINGS)
Tectum Inc. 105 South Sixth Street Newark, OH 43055 Phone: (888) 977-9691 Phone: (740) 345-9691 Fax: (800) 832-8869 E-mail: info@tectum.com www.tectum.com This MANU-SPEC utilizes the Construction Specifications
More informationEXTERIOR PLANK SERIES SPECIFICATION DATA
EXTERIOR PLANK SERIES SPECIFICATION DATA This specification includes the Exterior Plank ceiling system including suspension systems and components along with related work such as mechanical air grills,
More informationSECTION AXIOM INDIRECT FIELD LIGHT COVE PERIMETER SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 09 51 13 AXIOM INDIRECT FIELD LIGHT COVE PERIMETER SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of Contract, including General and Supplementary Conditions and
More informationSECTION COMPOSITE CORE ACOUSTICAL PANEL CEILINGS. Sound-Rite Inc. #9, rd Avenue NE Calgary, AB T2A 7P3
SECTION 09510 COMPOSITE CORE ACOUSTICAL PANEL CEILINGS Sound-Rite Inc. #9, 2821 3rd Avenue NE Calgary, AB T2A 7P3 Tel 403-296-0505 Fax 403-296-0511 Email info@sound-rite.com Web www.sound-rite.com Techstyle
More informationLOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS
0 0 0 SECTION 0. - ACOUSTICAL PANEL CEILINGS PART - GENERAL. SUMMARY A. This Section includes the following work:. Acoustical panels and exposed suspension systems for ceilings.. Patching of existing acoustical
More informationSECTION ACOUSTICAL CEILING SYSTEMS
SECTION 09 51 13 PART 1 - GENERAL 1.01 SUMMARY A. This Section includes the following: 1. Ceilings consisting of acoustical panels and exposed suspension systems. 2. T-Bar mounted light fixture support
More informationSECTION Axiom Roller Shade Integration
SECTION 09 51 13 Axiom Roller Shade Integration PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Section Includes: 1. Pre-engineered perimeter transition system B. Related sections: 1. Section 09 51
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095423 - LINEAR METAL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTHIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS. Rockfon CurvGrid One-Directional Curved Metal Ceiling Panels are meant for interior applications, specifications
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 09 5113 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
More informationSection SoundPly LR M25 Acoustic Ceiling Panels
Section 095126 Acoustic Ceiling Panels PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1
More informationSection Wood Veneer Ceiling Tiles Micro Perforated
Section 095426 Wood Veneer Ceiling Tiles Micro Perforated PART 1 GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division
More informationSection Wood Grille Ceiling Panels
Section 095426 Wood Grille Ceiling Panels PART 1 GENERAL RELATED DOCUMENTS Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1 Specification sections
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION DRYWALL GRID LINEAR LIGHTING INTEGRATION
SECTION 09 22 26 DRYWALL GRID LINEAR LIGHTING INTEGRATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of Contract, including General and Supplementary Conditions and Divisions-1
More informationARMSTRONG SHALL NOT BE LIABLE FOR ANY DAMAGES ARISING OUT OF THE USE OF ANY OF ITS GUIDE SPECIFICATIONS. SECTION PERIMETER TRANSITION SYSTEM
Armstrong World Industries, Inc. Please understand that you are responsible for the accuracy of all project specifications, including any Armstrong Ceilings guide specifications that you use. ARMSTRONG
More informationReferences in blue are general indicators to the specifier. If not used it can be deleted, but may be needed in the future.
General spec. notes: References in blue are general indicators to the specifier. If not used it can be deleted, but may be needed in the future. SECTION 095133 / 09 51 33 PANZ Metal Ceiling Panels and
More informationOptima Vector Plank. Installation Instructions. Ceiling
Ceiling Systems Between us, ideas become reality Optima Vector Plank Installation Instructions 1. GENERAL 1.1. Product Description The Vector products referenced in these instructions are made from fiberglass.
More informationSection Wood Veneer Ceiling Planks Linear
Section 095426 Wood Veneer Ceiling Planks Linear PART 1 GENERAL RELATED DOCUMENTS SUMMARY Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION ( Specialty Ceilings) TBAR LED Smartlight Acoustical Ceiling Integration
SECTION 09 50 00 (09 54 00 Specialty Ceilings) TBAR LED Smartlight Acoustical Ceiling Integration PART 1 - GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY Drawings and general conditions of Contract, including
More informationLINEAR METAL CEILINGS Section
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationSECTION Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco Ceramic Tile.
SECTION 09510 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310 - Ceramic Tile. 1.02 REFERENCES A. American
More informationTHIS SECTION IS BASED ON ROCKFON S TRADITIONS METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S TRADITIONS METAL CEILING PANELS. Rockfon Traditions Metal Ceiling Panels are meant for interior applications, specifications as shown here pertain to interior
More informationOPTIMA Vector Plank Installation Instructions
CEILING SYSTEMS Between us, ideas become reality OPTIMA Vector Plank Installation Instructions 1. GENERAL 1.1. Product Description The Vector products referenced in these instructions are made from fiberglass.
More informationSIMEILINGS TORSION SPRING CEILING SYSTEM SPECIFICATION
TORSION SPRING CEILING SYSTEM SPECIFICATION NOTICE: Consult your local Sound Concepts representative or contact Sound Concepts at 204.783.6297 before specifying any optional or custom element as shape,
More informationTHIS SECTION IS BASED ON ROCKFON S PLANOSTILE D LAY-IN METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S PLANOSTILE D LAY-IN METAL CEILING PANELS. Though Rockfon Planostile D Lay-In Metal Ceiling Panels are meant for interior and exterior applications, Specifications
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationSECTION ACOUSTICAL WALL TREATMENT (CEMENTITIOUS WOOD FIBER WALL PANELS)
Tectum Inc. 105 South Sixth Street Newark, OH 43055 Phone: (888) 977-9691 Phone: (740) 345-9691 Fax: (800) 832-8869 E-mail: info@tectum.com www.tectum.com This MANU-SPEC utilizes the Construction Specifications
More informationSECTION ACOUSTICAL CEILINGS
PART 1- GENERAL 1.1 DESCRIPTION SECTION 09 51 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationRULON WOOD SQUARE SUSPENDED CEILING SYSTEMS ARCHITECTURAL SPECIFICATIONS
12/6/2012 RULON WOOD SQUARE SUSPENDED CEILING SYSTEMS ARCHITECTURAL SPECIFICATIONS PART 1 - GENERAL A. The Wood Square Suspended Ceiling Systems covered by this specification shall be the products of the
More informationDIVISION 5 METALS SECTION COLD-FORMED METAL FRAMING
DIVISION 5 METALS SECTION 05 40 00 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMake Waves. Topo 3-Dimensional System
Make Waves Topo 3-Dimensional System User s Guide Topo panels are offered in translucent and opaque to work with existing lighting and complement any color palette. Optional preengineered utility circles
More informationOptima Vector Ultima Vector
CEILING&WALL SYSTEMS Between us, ideas become reality Optima Ultima Installation Instructions ceiling panel items: OPTIMA: 3900, 3901, 3902, 3903, 3904, 3905, 3906, 3907, 3908, 3909 ULTIMA: 1920, 1921
More informationSECTION Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco Ceramic Tile.
SECTION 09510 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310 - Ceramic Tile. 1.02 REFERENCES A. American
More informationTHIS SECTION IS BASED ON ROCKFON S SPANAIR HOOKON METAL CEILING PLANKS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S SPANAIR HOOKON METAL CEILING PLANKS. Rockfon SpanAir HookOn Metal Ceiling Planks are meant for interior applications, specifications as shown here pertain to interior
More informationHIR 1 ACOUSTICAL, IMPACT RESISTANT, TACKABLE WALL PANEL SPECIFICATION
HIR 1 ACOUSTICAL, IMPACT RESISTANT, TACKABLE WALL PANEL SPECIFICATION NOTICE: Consult your local Sound Concepts representative or contact Sound Concepts at 204.783.6297 before specifying any optional or
More informationSECTION (09800) - Suspended Acoustic Baffles. This Section is based on TECHLITE Accent Linear Ceiling Baffles.
SECTION 09 53 00 (09800) - Suspended Acoustic Baffles This Section is based on TECHLITE Accent Linear Ceiling Baffles. PART 1 - GENERAL 1.1 SUMMARY A. Section includes TECHLITE S Accent Linear Ceiling
More informationTHIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS. Though Rockfon Planostile Snap-In Metal Ceiling Panels are meant for interior and exterior applications, Specifications
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 092216 - COLD FORMED STEEL FRAMING - NON-STRUCTURAL (CFSF-NS) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ACTION
More informationACOUSTICAL WALL TREATMENT SECTION 09840
ACOUSTICAL WALL TREATMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Site-fabricated, stretched fabric acoustical wall system built with rigid polymer stretching system to secure fabric over the wall
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 - GENERAL 1.1 SUMMARY SECTION 09 21 16 A. Provide gypsum board assemblies as shown and specified. Work includes: 1. Walls, partitions, and soffits, including metal framing systems. 2. Acoustical
More informationSECTION STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 08110 - STEEL DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09 21 16 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Metal stud wall and ceiling framing, 20 gauge. B. Metal channel suspended ceiling framing. C. Gypsum board. D. Gypsum sheathing.
More informationSound-Rite Inc. #9, rd Avenue NE Calgary, AB T2A 7P3. Tel Fax Web
Tectum Inc. 105 South Sixth Street Newark, OH 43055 Phone: (888) 977-9691 Phone: (740) 345-9691 Fax: (800) 832-8869 E-mail: info@tectum.com www.tectum.com Sound-Rite Inc. #9, 2821 3 rd Avenue NE Calgary,
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION NON-STRUCTURAL METAL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 22 16 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationRULON ACOUSTICAL CEILING SYSTEM ALURATONE 100 ARCHITECTURAL SPECIFICATIONS
10/3/2012 RULON ACOUSTICAL CEILING SYSTEM ALURATONE 100 ARCHITECTURAL SPECIFICATIONS PART 1 - GENERAL A. The Rulon Aluratone Ceiling Systems covered by this specification shall be the products of the Rulon
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Cast
More informationSection SoundPly RF M25 Acoustic Wall Panels
Section 097714 Acoustic Wall Panels PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD
SECTION 09250 GYPSUM BOARD PART 1GENERAL 1.1 SUMMARY A. Related Documents: General and Supplementary Conditions of the Contract, Division 1 - General Requirements, and Drawings are collectively applicable
More informationA. Product Data: For each type of product specified.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationEast Central College
SECTION 123623 - PLASTIC-LAMINATE-CLAD COUNTERTOPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets
SECTION 09 29 00 - GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationRULON LINEAR OPEN SUSPENDED WOOD CEILING SYSTEMS ARCHITECTURAL SPECIFICATIONS
10/3/2012 RULON LINEAR OPEN SUSPENDED WOOD CEILING SYSTEMS ARCHITECTURAL SPECIFICATIONS PART 1 - GENERAL A. The natural wood ceiling systems covered by this specification shall be the products of the Rulon
More informationSECTION EXTERIOR METAL WALL PANELS SERIES PF
SECTION 07 42 13 EXTERIOR METAL WALL PANELS SERIES PF PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Extent of Wall Panels System is shown on drawings and schedules B. Drawings and general provisions of the Contract
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION GYPSUM BOARD PART 1 - GENERAL
SECTION 09250 - GYPSUM BOARD PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationDiSorb Diffuser Product Specifications Section Sound Diffuser-Absorber for Ceilings and Walls (DiSorb Diffuser-Absorber)
DiSorb Diffuser Product Specifications PART 1 - GENERAL 1.01 SUMMARY A. This section includes Sound Diffuser-Absorbers for Ceilings and/or Walls. Types include: 1.02 RELATED SECTIONS 1. DiSorb Diffuser-Absorber,
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationGeneral applications. Fast. Easy. Customer Focused.
C E I L I N G S U S P E N S I O N S Y S T E M S Fast. Easy. Customer Focused. General applications 200 Snap-Grid (Hook) /16) 250 Fire-Front Snap-Grid (Hook) /16) Seismic 1200 & 1200 (Stab) /16) 1250 Fire-Front
More informationSECTION PORTLAND CEMENT PLASTER (STUCCO) WITH ACRYLIC FINISH
SECTION 09 24 23 - PORTLAND CEMENT PLASTER (STUCCO) WITH ACRYLIC FINISH PART I - GENERAL 1.01 SECTION INCLUDES A. Building paper B. Lath and accessories C. Plaster materials D. Acrylic finish E. Exterior
More informationHome Depot Page 1 of 5 HDPB Humacao, PR 10/19/09
PART 1 - GENERAL 1.01 SUMMARY A. Types of cold-formed metal framing units include the following: 1. C-shaped steel studs B. Related work specified elsewhere includes but may not be limited to: 1. Section
More informationONE SCHOOL STREET SEPTEMBER 18, 2008 GOWANDA, NEW YORK ARCH PROJECT NO
SECTION 09265 - GYPSUM BOARD SHAFT-WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. Submit the following in addition to the standard requirements.
SECTION [13120] OMNIFLEX 300 MODULAR WALL SYSTEM SECTION 1 GENERAL 1.01 SECTION INCLUDES A. This Section specifies all requirements necessary to furnish and install a complete modular wall system including,
More informationTILE TILE
09300 - TILE 09300-1 PART ONE: GENERAL 1.1 Description TILE 1.1.1 Work of this Section, as shown or specified, shall be provided by the Interior Contractor and shall be in accordance with the requirements
More informationSECTION NON--STRUCTURAL METAL FRAMING
The Collective Voice of America s Steel Framing Industry The Steel Framing Industry Association (SFIA) is dedicated to expanding the market for cold-formed steel in construction through programs and initiatives
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationSubmittal Transmittal
Submittal Transmittal Standard St. Joe's - Sonntag Pavillion St. Joseph s Hospital 350 W. Thomas Road Phoenix, AZ 8503 Project # 5690A Tel: Fax: Kitchell Contractors Inc of AZ Date: 9/9/20 Reference Number:
More information