NanaWall Matching Windows and Doors Table of Contents
|
|
- Shawn Bradley
- 6 years ago
- Views:
Transcription
1 NanaWall Matching Windows and Doors Table of Contents Matching Windows and Doors Cross Sections and Maximum Frame Charts Introduction NanaWall French Doors Performance and Testing Results Maximum Frame Height Chart Fixed Panel Tilt Turn Window / Door NanaWall WA68 - Aluminum Clad Wood Fixed Panel and Tilt Turn Window / Door...9 NanaWall WD68 - Wood Framed Fixed Panel and Tilt Turn Window / Door NanaWall SL48 - Aluminum Framed Fixed Panel and Tilt Turn Window / Door NanaWall SL88 - Thermally Broken Aluminum Framed Fixed Panel and Tilt Turn Window / Door with HVHZ Option NanaWall SL68 - Thermally Broken Aluminum Framed Fixed Panel and Tilt Turn Window / Door Specifications SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems i
2
3 NanaWall Matching Windows and Doors Introduction Coordinated Walls Available are matching systems in aluminum-clad wood, wood, standard aluminum and thermally broken aluminum. Depending on sizes and wind load requirements, matching systems can be mulled (with appropriate structural support) with folding and individual panel sliding system. Fixed Windows and Storefront Fixed units are available for transoms above a folding or individual panel sliding unit. Center lines can be lined up. Sidelites are available with frame extenders so that horizontal glass lines are approximately the same. Complete storefronts are also available with a combination of mulled units. NanaWall Tilt Windows and Doors Available are tilt-turn windows, tilt-turn doors and tilt-only hopper windows. These systems are engineered to provide high weather resistance and structural performance, suitable for many high-rise structures and buildings in hurricane and other areas. Florida Approval SL88 thermally broken aluminum framed tilt turn window with frame size of 48" wide x 72" high is Florida state wide approved with Product Approval number FL It is also approved for use in the high velocity hurricane zone (HVHZ) with impact glass. This information with limitations can be viewed at www. floridabuilding.org. Performance Testing The tested sample unit of the SL 68 thermally broken aluminum framed tilt turn window met the performance requirements of AAMA DAW-C x 1829 (48x72) /DA-C100 48x72 rating. The tested sample unit of the SL 88 thermally broken aluminum framed tilt turn window met the performance requirements of AAMA DAW-C x 1829 (48x72)/DA-C70 48x72 rating. The tested sample unit of the WA68 aluminum-clad wood framed tilt turn window met the performance requirements of AAMA DAW-C x1822 (48x72). The tested sample unit of the WD 68 wood framed tilt turn window met the performance requirements of AAMA DAW-C x1828 (48x72). See Performance pages for details. Benefits of NanaWall Tilt Systems With tilt-turn hardware, large size operable openings are possible. Tilts Inward for Safe Ventilation. The tilt position opens up from the top, tilting in a few inches, for safe ventilation. Turns Inward for Easy Cleaning. With the turn position, the window swings in on its hinges to make cleaning the outside surface easy. For units used as transoms, tilt-only hopper windows can be supplied with operators so that high units can be easily opened and closed. NOTICE For mulled fixed or tilt turn units or a combination of different units, please consult with a qualified structural engineer to determine, based on project design wind loads and other requirements, if any structural stiffeners are needed between units. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 1
4 NanaWall Matching Windows and Doors Introduction NanaWall French Doors NanaWall French doors are available as single doors or pairs. Very narrow stiles and rails are possible. NanaWall French doors use exactly the same profiles and hardware as the matching NanaWall folding system. Hence, the same size charts, glazing options, wood/finish options and finish hardware options as the matching NanaWall folding system are applicable. The same testing performance results also apply (within a folding system, with an odd number of panels stacking to one side, the last panel is a swing door). For aluminum-clad, wood framed French doors, see WA67. For wood framed French doors, see WD66 and WD65. For standard aluminum framed French doors, see SL45. For thermally broken aluminum framed French doors, see SL60 and SL70. For Miami Dade / AAMA hurricane thermally broken aluminum framed French doors, see SL73. For structurally glazed aluminum framed French doors, see SL82. Technical Description The corresponding closest system match to NanaWall folding/sliding systems are as follows: Folding/sliding system WA67 WD65, WD66, HSW66 SL45, HSW45 SL60, HSW60 SL70 Corresponding matching fixed/tilt turn system WA68 WD68 SL48 SL68 SL88 Profile and Finish Options For WD 68 and WA 68 systems, standard woods available are Douglas Fir, Pine, or Meranti. Other woods are also available. Frames and panels have a sanding sealer or a base coat applied or for WA 68 system only, with one additional clear coat; see Wood Finish Options in the General Introduction. Standard aluminum finishes for the WA68, SL48 and SL88 systems are clear anodized and the 50 finishes shown in the NanaWall Powder Coating Finish Chart in the front of this binder. Powder coated finishes can be chosen from a range of over two hundred RAL colors; see Aluminum Finish Options in the General Introduction. Glazing Units are supplied glazed with double clear insulating safety, insulating Low-E safety glass, single (for SL48 and WD 68 systems only), other high performing safety glass such as triple glazing, Heat Mirror, special tint, etc., or other glass on request. Hinge Cover Options Covers for hinges can be white, brown or silver. Handle Options Standard: Stainless steel in brushed satin or black titanium finishes. Optional: Nylon available in white, dark brown or gray color or solid brass available in white, oil rubbed brass or satin nickel finishes. See "Hardware" in the General Introduction for other options NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
5 NanaWall Matching Windows and Doors Performance SL68 Thermally Broken Aluminum Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft psf (75 Pa): 0.04 (.20 L/s/m 2 psf (300 Pa): 0.11 (.56 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. No uncontrolled water 13.5 psf (645 Pa) Design Pressure psf (4800 Pa) Design Pressure psf (5270 Pa) *Forced Entry Resistance In accordance with ASTM F 588 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in August 2006, in accordance with AAMA/WDMA/CSA 101/I.S.2/A and AAMA/NWWDA 101/I.S.2-97 standards. The sample tested met the performance requirements for a DAW-C x 1829 (48 x 72)/DA-C100 48x72 rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure Allowable Design Wind Loading - PSF Frame Width Allowable Design Wind Loading - PSF Frame Width Frame Height See Maximum Frame Size Chart for Possible Sizes Frame Height See Maximum Frame Size Chart for Possible Sizes Please also note that chart is only applicable for units with referenced NanaWall supplied locking. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 3
6 NanaWall Matching Windows and Doors Performance SL88 Thermally Broken Aluminum Framed Tilt Turn Window/Door High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # Type of Test Performance Testing Results Result *Air Infiltration: Protocol TAS 202 and ASTM E-283, cfm/ft psf (75 Pa): psf (300 Pa): 0.25 *Water Penetration: Protocol TAS 202, ASTM E547 and E331 * Structural Load Deflection Protocol TAS 202 and ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. Missile Impact & Cycling: Protocols TAS 201 & 203, ASTM E 1886 and E 1996 No uncontrolled water 13.5 psf (645 Pa) Design Pressure psf (3350 Pa) Design Pressure psf (4785 Pa) WITH 1 1/8" INSULATED IMPACT GLASS Design Pressure 90 psf (4300 Pa) Design Pressure 120 psf (5260 Pa) *Forced Entry Resistance In accordance with ASTM F 588 * Excerpts of results of three separate units with sizes of 4 0 W x 6 0 H tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory, in October Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Allowable Design Wind Loading - PSF Positive Design Pressure Frame Height See Maximum Frame Size Chart for Possible Sizes Max. limited to cycling pressure Frame Width Allowable Design Wind Loading - PSF Negative Design Pressure Frame Height See Maximum Frame Size Chart for Possible Sizes Max. limited to cycling pressure Frame Width Please also note that chart is only applicable for units with referenced NanaWall supplied locking NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
7 NanaWall Matching Windows and Doors Performance WA68 Aluminum Clad Wood Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft psf (75 Pa): 0.01 (.1 L/s/m 2 psf (300 Pa): 0.15 (.8 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. *Forced Entry Resistance No uncontrolled water 12 psf ( 580 Pa) Design Pressure psf (2400 Pa) Design Pressure psf (3360 Pa) In accordance with ASTM F Grade 20 & CAWM 301 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A standard. The sample tested met the performance requirements for a DAW-C x 1822 (48 x 72) rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure Allowable Design Wind Loading - PSF Frame Width Allowable Design Wind Loading - PSF Frame Width Frame Height See Maximum Frame Size Chart for Possible Sizes Frame Height See Maximum Frame Size Chart for Possible Sizes Please also note that chart is only applicable for units with referenced NanaWall supplied locking. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 5
8 NanaWall Matching Windows and Doors Performance WD68 Wood Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft psf (75 Pa): 0.01 (.1 L/s/m 2 psf (300 Pa): 0.01 (.1 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 No uncontrolled water 13.5 psf (645 Pa) * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. *Forced Entry Resistance Design Pressure psf (3360 Pa) Design Pressure psf (5745 Pa) In accordance with ASTM F Grade 20 & CAWM 301 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A standard. The sample tested met the performance requirements for a DAW-C x 1828 (48 x 72) rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure Allowable Design Wind Loading - PSF Frame Height See Maximum Frame Size Chart for Possible Sizes Frame Width Allowable Design Wind Loading - PSF Frame Width Please also note that chart is only applicable for units with referenced NanaWall supplied locking Frame Height See Maximum Frame Size Chart for Possible Sizes NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
9 NanaWall Matching Windows and Doors Size Chart NanaWall Maximum Frame Size Chart Fixed Panel WA68, WD68, SL48, SL68, SL (3000) Any custom size is possible up to the maximum size shown. NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters 9 2 (2800) 8 6 (2600) Frame Height of Unit 7 10 (2400) 7 2 (2200) 6 6 (2000) 5 11 (1800) 5 3 (1600) 4 7 (1400) 3 11 (1200) 3 3 (1000) (600) (800) (1000) (1200) (1400) (1600) (1800) (2000) (2200) Frame Width of Unit Solid dark line on chart indicates maximum frame height possible for a given maximum frame width. The maximum size limits shown are based on the weight of a unit that has a net glass thickness of 5/16 (8mm). The composition of standard insulated glass is 5/32 glass/air space/ 5/32 glass. For other net glass thicknesses, this maximum size chart may not apply. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 7
10 NanaWall Matching Windows and Doors Size Chart NanaWall Maximum Frame Size Chart Tilt Turn Window/Door WA68, WD68, SL48, SL68, SL88 Any custom size is possible up to the maximum size shown. NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters 8 2 (2500) 7 10 (2400) 7 7 (2300) 7 3 (2200) 6 11 (2100) 6 7 (2000) Frame Height of Unit 6 3 (1900) 5 11 (1800) 5 7 (1700) 5 3 (1600) 4 11 (1500) 4 7 (1400) 4 3 (1300) 3 11 (1200) 3 7 (1100) 3 3 (1000) (600) (700) (800) (900) (1000) (1100) (1200) (1300) (1400) (1500) (1600) Frame Width of Unit Solid dark line on chart indicates maximum frame height possible for a given maximum frame width. The maximum size limits shown are based on the weight of a unit that has a net glass thickness of 5/16 (8mm). The composition of standard insulated glass is 5/32 glass/ air space/ 5/32 glass. For other net glass thicknesses, this maximum size chart may not apply NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
11 NanaWall Matching Windows and Doors NanaWall WA68 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Wood frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 9
12 NanaWall Matching Windows and Doors NanaWall WA68 Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt). All Cross-Sectional Views Are Half Size. Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
13 NanaWall Matching Windows and Doors NanaWall WD68 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Wood frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 11
14 NanaWall Matching Windows and Doors NanaWall WD68 Tilt Turn Window (Available as a single window or multiple unit). All Cross- Sectional Views Are Half Size Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
15 NanaWall Matching Windows and Doors NanaWall SL48 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 13
16 NanaWall Matching Windows and Doors NanaWall SL48 Tilt Turn Window All Cross-Sectional Views Are Half Size. (Available as a single window or as a pair. In a pair, only one panel can tilt.) Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
17 NanaWall Matching Windows and Doors NanaWall SL88 Thermally Broken Fixed Panel All Cross-Sectional Views Are Half Size. Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 15
18 NanaWall Matching Windows and Doors NanaWall SL88 Thermally Broken Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt.) All Cross-Sectional Views Are Half Size. High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
19 NanaWall Matching Windows and Doors NanaWall SL68 Thermally Broken Fixed Panel All Cross-Sectional Views Are Half Size. Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 17
20 NanaWall Matching Windows and Doors NanaWall SL68 Thermally Broken Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt.) All Cross-Sectional Views Are Half Size. Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
21 Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section : NanaWall SL88 Thermally Broken Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL88, the Thermally Broken Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC REFERENCES A. FL Building Code Compliance Offi ce Protocol: 1. TAS 201, Impact Test Procedures 2. TAS 202, Criteria for Testing Impact and Non Impact Resistant Building Envelope Components Using Uniform Static Air Pressure 3. TAS 203, Criteria for Testing Products Subject to Cyclic Wind Pressure Loading. B. A. American Architectural Manufacturers Association (AAMA): AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.. C. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. D. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference. 4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. 5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies. E. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 19
22 NanaWall Matching Windows and Doors Guide Specifications completion date, type and size of unit installed QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/ WDMA/CSA 101/I.S.2/A440 Testing results to include air infi ltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330 and forced entry in accordance with ASTM F 588. C. Performance Criteria with Impact Glass: The SL88 is approved for High Velocity Hurricane Zone (HVHZ) with Impact Glass with FL Product Approval # ** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). See manufacturer's latest published data. D. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. B. Do not use forced heat to dry out building. C. Store fl at in dry, well ventilated area out of direct sunlight. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL Meadow Creek Drive, Corte Madera, CA Toll Free: (800) Telephone: (415) Fax: (415) Website: info@nanawall.com NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
23 Guide Specifications NanaWall Matching Windows and Doors B. Other suppliers equal to the specifi ed product must submit substitution request two weeks before bid for prior approval MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated conforming to AAMA Thermally broken with ¾ -15/16 (20-24 mm) polyamide plastic reinforced with glass fi bers with additional insulating foam. 4. Aluminum Finish: B. Glass: Select from NanaWall Powder Coating Finish Chart [OR clear anodized] [OR dark bronze anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR select from range of Wood Grain powder coated fi nish] [OR custom fi nish]. Same [OR different] fi nishes on inside and outside. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR /16 (24 mm) insulating clear safety [OR 15/16 (24 mm) double glazed insulating argon fi lled Low-E safety] [OR 1 ½ (38 mm triple glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. Provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism. a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 21
24 NanaWall Matching Windows and Doors Guide Specifications panel]. D. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. B. Provide other side lites, transoms as per drawings provided. PART 3 EXECUTION 3.01 ERECTION A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on the fl oor. C. Installation of units constitutes acceptance of existing conditions INSTALLATION A. Install frame in accordance with manufacturer s recommendations and installation instructions. Properly fl ash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. Install sash and handles in accordance with manufacturer s recommendations and installation instructions. D. If necessary, adjust hardware for proper operation. E. Accessories: Screens; install in accordance with screen manufacturer s recommendations and installation instructions. END OF SECTION DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular requirements of a specifi c construction project NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
25 Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section NanaWall SL48 Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL48, the Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights. 2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum. 3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. C. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. B. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 23
26 NanaWall Matching Windows and Doors Guide Specifications 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. B. Do not use forced heat to dry out building. C. Store fl at in dry, well ventilated area out of direct sunlight. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL Meadow Creek Drive, Corte Madera, CA Toll Free: (800) Telephone: (415) Fax: (415) Website: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA or powder coated conforming to AAMA Aluminum Finish: B. Glass: Select from NanaWall Powder Coating Finish Chart [OR dark bronze anodized] [OR clear anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR custom fi nish]. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120 1/4 (6 mm) tempered [OR ¼ (6 mm) laminated] [OR ¾ (20 mm) insulating clear safety] [OR ¾ (20 mm) double glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. For insulated units, provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
27 Guide Specifications NanaWall Matching Windows and Doors a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. D. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of panel]. E. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. B. Provide other side lites, transoms as per drawings provided. PART 3 EXECUTION 3.01 ERECTION A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on the fl oor. C. Installation of units constitutes acceptance of existing conditions INSTALLATION A. Install frame in accordance with manufacturer s recommendations and installation instructions. Properly fl ash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. Install sash and handles in accordance with manufacturer s recommendations and installation instructions. D. If necessary, adjust hardware for proper operation. E. Accessories: Screens; install in accordance with screen manufacturer s recommendations and installation instructions. END OF SECTION SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 25
28 NanaWall Matching Windows and Doors Guide Specifications DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular requirements of a specifi c construction project. THIS PAGE BLANK NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
29 Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section NanaWall SL68 Thermally Broken Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL68, the Thermally Broken Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights. 2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum. 3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference. 4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. 5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 27
30 NanaWall Matching Windows and Doors Guide Specifications B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/ WDMA/CSA 101/I.S.2/A440-0 Testing results to include air infi ltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330 and forced entry in accordance with ASTM F 588. ** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). See manufacturer's latest published data. C. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL Meadow Creek Drive, Corte Madera, CA Toll Free: (800) Telephone: (415) Fax: (415) Website: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated conforming to AAMA Thermally broken with ¾ -15/16 (20-24 mm) polyamide plastic reinforced with glass fi bers with additional insulating foam. 4. Aluminum Finish: Select from NanaWall Powder Coating Finish Chart NanaWall Systems SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.
31 Guide Specifications NanaWall Matching Windows and Doors B. Glass: [OR dark bronze anodized] [OR clear anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR Wood Grain Finish] Same [OR different] fi nishes on inside and outside. [OR custom fi nish]. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR /16 (24 mm) insulating clear safety [OR 15/16 (24 mm) double glazed insulating argon fi lled Low-E safety] [OR 1 ½ (38 mm triple glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. For insulated units, provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism. a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, hinges pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. D. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of panel]. E. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems 29
Guide Specifications - Section SL35. NanaWall SL35, Aluminum Framed Folding System PART 1 - GENERAL
NanaWall SL35, Aluminum Framed Folding System PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Engineered sliding/folding aluminum and glass door system, including aluminum frame, threshold, panels,
More informationSL45 Guide Specifications - Section
NanaWall SL45- Monumental Aluminum Framed Folding/Paired Panel System PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Sliding/folding aluminum and glass door system, including aluminum frame, threshold,
More informationWD65 Guide Specifications - Section
WD65 Guide Specifications - Section 084100 NanaWall WD65 - Wood Framed Folding/Paired Panel System PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Engineered sliding/folding wood and glass door system,
More informationGuide Specifications - Section : NanaWall WD65 - Wood Framed Folding/Paired Panel System PART 1 GENERAL
Guide Specifications - Section 084100: NanaWall WD65 - Wood Framed Folding/Paired Panel System PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Engineered sliding/folding wood and glass door system, including
More informationSL35 Introduction. NanaWall SL35 The Standard Aluminum Framed Folding System
SL35 Introduction NanaWall SL35 The Standard Aluminum Framed Folding System The SL35 is an aluminum folding panel system designed to provide a moving glass wall for openings as wide as 39. It is a top-hung
More informationGuide Specifications - Section HSW66
Guide Specifications - Section 084100 HSW66 NanaWall HSW66 The Wood Framed Single Track Sliding System Part 1 General 1.01 Summary A. Section Includes: Individual panel wood and glass door sliding system,
More informationWA67 Guide Specifications - Section
NanaWall WA67- Aluminum Clad Wood Framed Folding System PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: Engineered sliding/folding aluminum clad wood and glass door system, including aluminum clad wood
More informationWD66 Guide Specifications - Section
WD66 Guide Specifications - Section 084100 NanaWall WD66 - Standard Wood Framed Folding System PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Engineered sliding/folding wood and glass door system, including
More informationHSW45 Introduction. NanaWall HSW45 Standard Aluminum Framed Single Track Sliding System
HSW45 Introduction NanaWall HSW45 Standard Aluminum Framed Single Track Sliding System The standard aluminum framed HSW45 System provides an efficient and convenient entrance system for residential, commercial
More informationSL70 Introduction. NanaWall SL70 The Monumental Thermally Broken Aluminum Framed Folding System
SL70 Introduction NanaWall SL70 The Monumental Thermally Broken Aluminum Framed Folding System The SL70 is a monumentally-sized, thermally broken aluminum folding panel system designed to provide an opening
More informationSL60 Introduction. NanaWall SL60 The Standard Thermally Broken Aluminum Framed Folding System
NanaWall SL60 The Standard Thermally Broken Aluminum Framed Folding System The SL60 is a thermally broken, aluminum folding panel system designed to provide an opening glass wall for openings up to 39
More informationGuide Specifications- Section
Guide Specifications- Section 084113 LaCantina ALUMINUM Folding Door System PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum and glass folding door system with fingertip operation up to 52 wide and 10
More informationSL25 NanaGlass Introduction
SL25 NanaGlass Introduction NanaWall SL25 The All Glass Opening Window Wall System without Vertical Stiles The SL25 all glass opening window wall system encloses a space, such as a balcony, porch, under
More informationThe Structurally Glazed Folding System with Exterior All Glass Aesthetic
INTRODUCTION SL82 The Structurally Glazed Folding System with Exterior All Glass Aesthetic The SL82 is a thermally broken aluminum folding panel system that presents a stunning almost uninterrupted exterior
More informationGuide Specifications- Section
Guide Specifications- Section 084113 LaCantina ALUMINUM Folding Door System PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum and glass folding door system with fingertip operation up to 52 wide and 10
More informationThe Aluminum Framed Monumental Folding/Paired Panel System
INTRODUCTION SL45 The Aluminum Framed Monumental Folding/Paired Panel System The SL45 is a monumental, standard aluminum folding or paired panel system. As a folding system, it is designed to provide an
More informationGUIDE SPECIFICATIONS - SECTION
GUIDE SPECIFICATIONS - SECTION 084110 LaCantina CLAD Folding Door System PART 1 GENERAL 1.01 SECTION INCLUDES A. Wood, aluminum and glass folding door system with fingertip operation up to 52 wide and
More informationSL73 - Aluminum Framed Thermally Broken Hurricane Approved Folding System
INTRODUCTION SL73 SL73 - Aluminum Framed Thermally Broken Hurricane Approved Folding System Miami-Dade County, FL NOA No. 15-0226.05 and 15-0226.06 (expiration 8/11/2020) Suitable for both Mid and Low
More informationHSW60 Introduction. NanaWall HSW60 The Thermally Broken Aluminum Framed Single Track Sliding System
HSW60 Introduction NanaWall HSW60 The Thermally Broken Aluminum Framed Single Track Sliding System and Rw values of 43 with the head track recessed and 41 with the head track exposed. The same unit with
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More informationWD66 The Standard Wood Framed Folding System
INTRODUCTION WD66 WD66 The Standard Wood Framed Folding System Weather Resistant Engineered to provide high weather resistance and structural performance. Excellent results were achieved with independent
More informationSL70 The Monumental Thermally Broken Aluminum Framed Folding System
INTRODUCTION SL70 SL70 The Monumental Thermally Broken Aluminum Framed Folding System The SL70 is a monumentally-sized, thermally broken aluminum framed folding panel system designed to provide an opening
More informationFL550 21/2 x5 GUIDE SPECIFICATION. Impact-Resistant Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationVSW65 BeyondLiftSlide / SwingSlide Introduction
VSW65 BeyondLiftSlide / SwingSlide Introduction VSW65 - BeyondLiftSlide The VSW65 BeyondLiftSlide is a wood-framed, individual panel sliding door system that makes large glass openings possible. With its
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
More informationPRODUCT SPECIFICATION THE 9500 SERIES FAMILY - SERIES 9502 / 9503 THERMALLY BROKEN ALUMINUM OUTSWING BALCONY DOOR
PART 1 - GENERAL 08 13 16 ALUMINUM DOORS (Outswing Aluminum-Framed Glass Doors) A high-quality thermally broken aluminum balcony outswing door designed for residential high rise construction. 1.1 SUMMARY
More informationSECTION FOLDING GLASS PARTITIONS
NANAWALL AcoustiFOLD THERMALLY BROKEN ALUMINUM FRAMED FOLDING PANEL SYSTEM SECTION 10 22 39 GUIDE SPECIFICATION 2018 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY A. Section includes furnishing and
More informationWD66 The Standard Wood Framed Folding System
INTRODUCTION WD66 WD66 The Standard Wood Framed Folding System Weather Resistant Life Cycle Performance Engineered to provide high weather resistance and structural performance. Excellent results were
More informationSECTION FOLDING GLASS PARTITIONS
NANAWALL SL70 MONUMENTAL, THERMALLY BROKEN ALUM. FRAMED FOLDING SYSTEM SECTION 10 22 39 GUIDE SPECIFICATION 2016 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY A. Section includes furnishing and installing
More informationSECTION VINYL WINDOWS AND DOORS. 2.2 Slider Windows Classic Series (Standard sizes) and Thermo-Fit Series (Custom sizes)
SECTION 08560 VINYL WINDOWS AND DOORS PART 1- GENERAL 1.1 SECTION INCLUDES: 2.2 Slider Windows Classic Series (Standard sizes) and Thermo-Fit Series (Custom sizes) 2.3 Slider Windows Generations Series
More informationSECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
More informationFL200 13/4 x41/2 GUIDE SPECIFICATION. Non-Thermal Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSLIDING SECTION 8 SPECIFICATIONS
GUIDE SPECIFICATIONS - SECTION 081373 LaCantina ALUMINUM Sliding Door System PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum multi-slide doors. B. Aluminum slider doors. C. Aluminum Thermally Controlled
More informationSECTION SLIDING GLASS PARTITIONS
SECTION 10 22 43 PART 1 GENERAL 1.01 SUMMARY A. Section includes furnishing and installing a single track, sliding thermally broken aluminum framed glass door, wall or partition panel system that includes:
More informationPRODUCT SPECIFICATION SERIES 5000T PUNCHED WINDOW THERMALLY BROKEN ALUMINUM CASEMENT/AWNING/ FIXED WINDOW
08 51 13 ALUMINUM WINDOWS PART 1 - GENERAL A high-quality thermally broken 3 ½ aluminum window designed for residential low, mid and high rise construction. 1.1 SUMMARY A. Section Includes: Aluminum Windows:
More informationPRODUCT SPECIFICATION SERIES 4500T THERMALLY BROKEN ALUMINUM SLIDING BALCONY DOOR
08 2 1 SLIDING ALUMINUM FRAMED GLASS DOOR PART 1 - GENERAL A high-quality thermally broken aluminum balcony sliding door designed for residential high rise construction. 1.1 SUMMARY A. Section Includes:
More informationA. Section Cast-In-Place Concrete: Openings in cast-in-place concrete.
Euro Vista Multi Slide Impact Rated Multi Slide Door PART 1 GENERAL 1.1 SECTION INCLUDES A. Sliding/Folding Doors. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete: Openings in cast-in-place
More informationWD65 Wood Framed Folding/Paired Panel System for Special Applications
INTRODUCTION WD65 WD65 Wood Framed Folding/Paired Panel System for Special Applications The WD65 is the folding or paired-panel wood framed system for special applications designed to provide an opening
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationSECTION FOLDING GLASS STOREFRONTS SECTION FOLDING GLASS DOORS
SECTION 08 43 33 PART 1 GENERAL 1.01 SUMMARY SECTION 08 35 13 FOLDING GLASS DOORS NOTE: Modify footers to align when using this section name and number. A. Section includes furnishing and installing a
More informationSeries B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
More informationFL550T 21/2 x5. GUIDE SPECIFICATION Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront. Thermal Impact-Resistant Storefront
Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationImpact-Resistant Entrances Series
ARCHITECTURAL PRODUCTS Impact-Resistant Entrances Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES
More informationSECTION ALL ULTREX DOUBLE HUNG WINDOW
SECTION 08 54 13 ALL ULTREX DOUBLE HUNG WINDOW PART 1 GENERAL 1.1 SECTION INCLUDES A. All Ultrex double hung window complete with hardware, glazing, weather strip, insect screen and half screen, grillesbetween-the
More informationSECTION PREHUNG WOOD DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08 14 00 PREHUNG WOOD DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2014-2016 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. French Doors.
More informationGUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM
1 GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials and services to furnish and install SECURITY
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationTRUMAN STATE UNIVERSITY GREENWOOD SCHOOL WINDOW REPLACEMENT
SECTION 085200 - WOOD WINDOWS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION K. Section Millwork: Wood trim other than furnished by door and frame manufacturer
SECTION 08 16 14 ULTREX CLAD WOOD SWINGING DOOR PART 1 GENERAL 1.1 SECTION INCLUDES A. Ultrex clad wood swinging door and frame, complete with hardware, glazing, weather strip, screen, removable grilles,
More informationSPECIFICATION GUIDE SERIES 800 HEAVY PICTURE WINDOW
SERIES 800 HEAVY PICTURE WINDOW Page 1 of 6 SPECIFICATION GUIDE SERIES 800 HEAVY PICTURE WINDOW www.ramwindows.com RAM Windows Series 800 Heavy Picture window is a custom residential and commercial window
More informationPRODUCT SPECIFICATION UNITIZED CURTAIN WALL THERMALLY BROKEN ALUMINUM AWNING/ FIXED WINDOW
08 44 13 GLAZED UNITIZED ALUMINUM CURTAIN WALL PART 1 - GENERAL A high-quality thermally broken aluminum unitized curtain wall system. The glass will be captured at the head, sill and stack joint locations.
More informationSILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
More information2000/2100/2200 Series Heavy Commercial Sliding Patio Doors
2000/2100/2200 Series Heavy Commercial Sliding Patio Doors MANKO WINDOW SYSTEMS, INC. 800 HAYES DRIVE MANHATTAN, KANSAS 66502 PHONE: (800) 642-1488 (785) 776-9643 FAX: (800) 576-2656 (785) 776-9644 MANKO
More informationUnited Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
More informationSECTION ALL GLASS ACOUSTIC SLIDING PARTITION
NANAWALL PrivaSEE ALL-GLASS SINGLE-TRACK ACOUSTIC SLIDING SYSTEM SECTION 10 22 00 GUIDE SPECIFICATION 2016 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY A. Section includes furnishing and installing
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
More informationSECTION SERIES 200 DOUBLE-HUNG VINYL WINDOWS
SERIES 200 DOUBLE-HUNG VINYL WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Replacement Windows. 1. Double hung windows 1.2 RELATED SECTIONS A. Section 05450: Cold Formed Metal Framing. B. Section 06100:
More informationPRODUCT SPECIFICATION SERIES 9000 WINDOW WALL THERMALLY BROKEN ALUMINUM CASEMENT / AWNING / FIXED WINDOW
08 46 3 GLAZED ALUMINUM WINDOW WALL PART - GENERAL A high-quality thermally broken 4 ½ aluminum window wall designed for residential high rise construction.. SUMMARY A. Section Includes: Glazed Aluminum
More informationSECTION ALL GLASS CENTER PIVOT PARTITIONS
NANAWALL CSW75 FRAMELESS CENTER PIVOT SYSTEM GUIDE SPECIFICATION 2018 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY SECTION 10 22 39 A. Section includes furnishing and installing a top-hung, hinged-panel,
More informationCTB Commercial Aluminum Window
Technical Information Description The is thermally-broken for use in commercial construction. Basic models include horizontal slider, single hung and fixed picture windows. Units are mulled together with
More information4600 Series Specifications (Section 08520)
4600 Series Specifications (Section 08520) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for this project as
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationSECTION SLIDING GLASS STOREFRONTS SECTION SLIDING ALUMINUM-FRAMED GLASS DOORS
NANAWALL HSW60 THERMALLY BROKEN ALUMINUM FRAMED SINGLE TRACK SLIDING SYSTEM SECTION 08 43 29 GUIDE SPECIFICATION 2016 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY SECTION 08 32 13 SLIDING ALUMINUM-FRAMED
More informationSPECIFICATION SECTION : FIRE RATED GLASS & FRAMING GPX Hurricane System
Welcome to the SAFTIFIRST TM Guide Specification System prepared as an aid to specifiers in preparing written construction documents. For specification assistance with specific product applications, please
More informationSECTION STAINLESS STEEL WALL PANELS
SECTION 07400 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Dry joint, Rainscreen stainless steel wall panel system. 2. Accessories including attachments, clips, sub girts, shims, and fasteners 3.
More informationSIDE HINGED SECURITY ALUMINUM WINDOWS
08 51 13.11 PART 1 - GENERAL 1.1 SECTION INCLUDES: A. Material: aluminum windows as on the drawings and specified in this section. B. Installation: labor, tools, and material needed to install aluminum
More informationPW251 21/2 x7 GUIDE SPECIFICATION. Curtain Wall
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08900 ALUMINUM CURTAIN WALL This suggested guide specification has
More informationSECTION FOLDING GLASS STOREFRONTS SECTION FOLDING GLASS DOORS
NANAWALL SL80 / 81 THERMALLY BROKEN ALUMINUM FRAMED FOLDING PANEL SYSTEM SECTION 08 43 33 GUIDE SPECIFICATION 2016 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY SECTION 08 35 13 FOLDING GLASS DOORS
More informationSeries 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationVELUX America Inc. SPECIFICATION FOR MODEL QPF SELF-FLASHED FIXED SKYLIGHT SECTION UNIT SKYLIGHTS
SECTION 08620 UNIT SKYLIGHTS PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance and product component information for VELUX QPF selfflashed fixed skylight. B. Unit skylight mounted directly to roof decking.
More informationCustom fabrication in two weeks or less, guaranteed.
Custom fabrication in two weeks or less, guaranteed. Ask us how Ramco can now fabricate hardware on all manufacturers blank doors in 2 weeks or less. ramcometals.com got lead times? Ramco offers custom
More informationAAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT SUMMARY. Rendered to:
AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT SUMMARY Rendered to: AluminTechno LLC. 12 Selitskog Street, Room 211 FEZ Minsk, Minsk District, Minsk Region 220075 Republic
More informationMPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
More informationSECTION U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR
Page 1 of 6 SECTION 08 39 80 U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR U.S. Aluminum has designed one of the most demanding air and water protection products, the BAL- 350 Small
More informationSILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
More informationSection D2 Table of Contents. 21/2 x 5. Specifications - FL S1-S5. Features and Benefits High Velocity Hurricane Zone Applications...
FL500 21/2 x5 Section D2 Table of Contents 21/2 x 5 Specifications - FL500... S1-S5 Features and Benefits... 1 High Velocity Hurricane Zone Applications... 2-3 Standard Framing - Wet Glazed... 4 Standard
More informationSeries 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationMPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
More information6400 Series TRIPLE GLAZED THERMAL BREAK CHURCH WINDOWS America's finest custom windows MINIMUM 5 8" AIR SPACE 3 1 2" SCALE = FULL SIZE
Since 906 Series The Series is a heavy triple glazed church window incorporated into a " thermally broken frame. The thermal break is achieved with the use of Thermal Strip technology. Two different aluminum
More informationAluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS
Aluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS This suggested guide specification has been developed using the current edition
More informationSeries 890-I Equa-Vu Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 890-I Equa-Vu 3 1 2 Heavy Commercial Projected Window Configurations Project-In Casement Inswing Fixed Series 890-I retains an AAMA Architectural Grade
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationSection Aluminum Windows (2700 Model Specifications)
Section 08520 - Aluminum Windows (2700 Model Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
More informationSTOREFRONTS FL500 Impact Table of Contents
STOREFRONTS FL500 Impact Table of Contents B4 Section Page Specifi cations - FL500... B4... S1-5 Options and Limitations (Wet Glaze / Dry Glaze)... B4... 1-2 Performance... B4... 3 Framing Details (Wet
More informationYSD 700H PRODUCT DATA
SYSTEM DESCRIPTION: The ProTek YSD 700 sliding glass door is designed to provide protection from the fierce cyclical pressures and projectiles associated with hurricane force winds. The engineering behind
More informationSuperior by Design. Approved for use in Miami-Dade HVHZ Zones Florida Building Code Approved Product Approval FL 15472
Superior by Design. E u r o - F D 3 F r e n c h D o o r S y s t e m Approved for use in Miami-Dade HVHZ Zones Florida Building Code Approved Product Approval FL 15472 w w w. e u r o - w a l l. c o m 8
More informationSERIES 9000 AW-PG70-DAW DUAL ACTING WINDOW (TILT/TURN)
PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
More informationAAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA TEST REPORT SUMMARY
AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 AAMA 910-93 TEST REPORT SUMMARY Rendered to: GIESSE NORTH AMERICA 2014 Holston Industrial Drive Blountville, TN 37617 PRODUCT TYPE: XO Sliding
More informationVinyl Window Designs Ltd. 550 Oakdale Road Toronto, ON M3N 1W6 SPECIFICATIONS
Vinyl Window Designs Ltd. 550 Oakdale Road Toronto, ON M3N 1W6 DIVISION 08 / SECTION 08560, VINYL WINDOWS SPECIFICATIONS 1.0. Section includes: 1. All windows of the types and sizes as called for in this
More informationSection D3 Table of Contents. 21/2 x 5. Specifications - FL S1-S5. Features and Benefits High Velocity Hurricane Zone Applications...
FL550 21/2 x5 Section D3 Table of Contents 21/2 x 5 Specifications - FL550... S1-S5 Features and Benefits... 1 High Velocity Hurricane Zone Applications... 2-3 Standard Framing - Wet Glazed... 4 Standard
More informationNanaWall HSW60 - Thermally Broken Aluminum Framed Single Track Sliding System
TABLE OF CONTENTS HSW60 NanaWall HSW60 - Thermally Broken Aluminum Framed Single Track Sliding System Introduction................................................................................1 Technical
More informationSECTION SLIDING ALUMINUM-FRAMED GLASS DOORS Panda Windows and Doors, Thermally Broken Multi-Slide Door Systems
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying Thermally Broken Multi-Slide Door Systems, and their installation. Panda Windows and Doors products
More informationCASEMENT PROJECT OUT SERIES 2400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 2 3/8
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 2400
More informationSECTION WOOD FRAMED FOLDING GLASS PARTITIONS
NANAWALL WD66 STANDARD WOOD FRAMED FOLDING SYSTEM SECTION 10 22 41 GUIDE SPECIFICATION 2016 Nana Wall Systems, Inc. PART 1 GENERAL 1.01 SUMMARY WOOD FRAMED FOLDING GLASS PARTITION A. Section includes furnishing
More informationCASEMENT PROJECT OUT SERIES 6400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 6400
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationSeries 510-I Thermal Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 510-I Thermal 2-7 16 Heavy Commercial Projected Window Configurations Project-In Project-Out Casement Fixed Series 510-I retains an AAMA Architectural
More information