INT 9.2 PLASTER AND GYPSUM BOARD (GYPSUM WALLBOARD, DRYWALL, SHEET ROCK TYPE MATERIAL, & TEXTURE FINISHES, ETC.)
|
|
- Antony Gregory
- 6 years ago
- Views:
Transcription
1 Interior System Evaluation 9.2 INT 9.2 PLASTER AND GYPSUM BOARD (GYPSUM WALLBOARD, DRYWALL, SHEET ROCK TYPE MATERIAL, & TEXTURE FINISHES, ETC.) The Substrate (i.e. surface) Plaster is a hard, gypsum based material found in many older homes and in some new custom designed buildings and restorations. A heavy base or ground coat is applied to wood or metal lathe attached to wall studs, and then smooth finishing plaster is troweled over top. In many new plaster applications, a gypsum cored, paper coated board is used instead of traditional wood lathe. This reduces the amount of base coat by about 40%. The method of application of finishing plaster can be varied to obtain a surface that can be smooth to rough in texture (e.g. Trowel - for a smooth surface; Floated or Sand Float finish - low stipple texture; Spray texture finish - smooth to moderately rough spatter texture; and textured finish - low to rough texture with a wide variety of patterns). Drywall panels ( gyproc, sheet rock, gypsum board, etc.) are the most common interior wall surfacing material. These are constructed of a gypsum-based core with a paper coating on all sides. Special purpose panels for fire resistance, damp proofing, and strength, use variations in the core and surfacing material. These panels are attached to vertical framing studs by either galvanized spiral shanked nails, or coated screws, then the seams between the panels are supported with a paper or fiber mesh tape, and filled with a plaster-like joint filler. A uniform painted finish cannot be obtained unless the filler is properly finished. Small defects, such as pinholes, ridging and fiber-lift, become very apparent after painting. Deep and dark colors should be avoided in high traffic areas on both substrates, as they are prone to marking. The Options (i.e. choices) INT 9.2A INT 9.2B INT 9.2C INT 9.2E INT 9.2F INT 9.2G INT 9.2H INT 9.2J INT 9.2K INT 9.2L INT 9.2M LATEX (over latex sealer) (Gloss/Sheen as Specified) HIGH PERFORMANCE ARCHITECTURAL LATEX (Gloss/Sheen as Specified) ALKYD (over latex sealer) (Gloss/Sheen as Specified) EPOXY ( TILE LIKE ) EPOXY, W.B. ( TILE LIKE ) MULTICOLOR FIRE RETARDANT COATING (Clear or Pigmented) W.B. FIRE RETARDANT COATING LATEX (over alkyd primer) (For Plaster, Only) (Gloss/Sheen as Specified) W.B. LIGHT INDUSTRIAL COATING (Gloss/Sheen as Specified) INSTITUTIONAL LOW ODOR / VOC (Gloss/Sheen as Specified) INT 9.2A LATEX (OVER LATEX SEALER) Conventional Latex is a standard performance latex system, which provides suitable performance for residential use and light use areas in commercial and industrial installations such as offices and meeting rooms. Latex finish systems are often used on plaster and gypsum board subjected to a low to moderate amount of cleaning or abrasion for residential, light industrial (e.g. warehouse), and commercial buildings. The detergent and abrasion resistance is not as good as the alkyd system, but the color retention and resistance to yellowing is better. These systems offer a range of gloss finishes for different applications. The low sheen of the flat finish assists in improving the uniformity of slightly rough surfaces. Semi-gloss and gloss finishes are often used for accent striping or signage and/or for smoother surfaces. They are also helpful in reducing dirt and dust accumulation and are easily cleaned, but will accentuate the surface roughness. System Finish Gloss Levels -G1 MPI Gloss Level 1 Flat or matte Mainly used: - Flat paints are widely used on large, smooth, or textured wall surfaces. Pros: - Very easy to touch-up. Minimizes visibility of surface imperfections Cons:- Easily marked and stained. Not recommended for surfaces exposed to constant contact, since burnishing and dirt pick-up would be excessive. -G2 MPI Gloss Level 2 Low Sheen like velvet cloth Widely used on wall surfaces such as offices and other low traffic areas. Pros: - Ease of touch-up, uniform appearance, marks less than Level 1 Cons:- Marks easier and is less washable than Level 3 -G3 MPI Gloss Level 3 like an egg s shell Provides a balance of washability and durability while avoiding an overly glossy appearance. Pros: - Washability Cons:- Shows substrate defects -G4 MPI Gloss Level 4 like satin cloth Provides a higher level of durability, but sheen accents surface defects. Pros: - Quite washable, etc. Cons:- Shows substrate defects, and reflects light somewhat -G5 MPI Gloss Level 5 Semi-Gloss Principal uses:- where washability and abrasion resistance properties are most important Pros: - Resistant to stains and dirt retention Cons:- Difficult to touch up and shows substrate defects. -G6 MPI Gloss Level 6 - Gloss Principal uses:- Rarely used, except on smooth surfaces. Pros: - Ease of clean up (i.e. washability) and abrasion resistance Cons:- Highly light reflective and shows all substrate defects. Very difficult to touch-up
2 INT 9.2B HIGH PERFORMANCE ARCHITECTURAL LATEX High Performance Architectural Latex is a high performance system, which provides a significant benefit in the areas of scrub resistance, resistance to marking and burnishing, and removal of stains and marks from the surface. It provides suitable performance for use in commercial and institutional uses such as schools, public buildings, hospitals, etc. It provides increased washability compared to conventional latex products. They also provide increased resistance to staining, and ease of soil removal. The low and intermediate levels of gloss possess much better resistance to burnishing than conventional latex products. These systems provide almost equivalent performance to alkyds, but without the objectionable odor and with a greater friendliness to the environment. However, they are more sensitive to cleaners containing strong solvents than are the alkyd systems. System Finish Gloss Levels -G2 MPI Gloss Level 2 Low Sheen like velvet cloth Used on surfaces where greater durability and stain resistance than conventional latex is desired. Pros: - Ease of touch-up, uniform appearance, marks less than Gloss Level 1 (G1) Cons:- Marks easier and is less washable than Level 3 -G3 MPI Gloss Level 3 like an egg s shell Common usage in corridors and hallways Pros: - Washability. Provides a higher level of durability than Gloss Level 2 (G2) Cons:- Shows substrate defects -G4 MPI Gloss Level 4 like satin cloth Often used in high use corridors, but not as reflective as Semi-Gloss Pros: - Quite washable, etc. Cons:- Shows substrate defects, and reflects light somewhat. Difficult to touch up. -G5 MPI Gloss Level 5 Semi-Gloss Uses:- where washability, abrasion resistance and stain removal properties are most important Pros: - Resistant to stains and dirt retention Cons:- Difficult to touch up INT 9.2C ALKYD (OVER LATEX SEALER) This system is a general-purpose system for residential and commercial applications, where moderate chemical and good physical resistance properties are required. Available in glosses ranging from eggshell to gloss. Gloss Level 3 is often used in areas not exposed to repeated contact from cleaning, as this finish can show marking, particularly in deep or bright tinted colors. For high traffic areas subjected to repeated contact, or requiring regular cleaning, semi-gloss and gloss finishes are often used. These have better stain, marking and abrasion resistance than the flat or eggshell finishes. The alkyd has better water and detergent resistance than the latex (INT 9.2A), and would be preferred in higher traffic locations requiring repeated cleaning. System Finish Gloss Levels -G1 MPI Gloss Level 1 Flat or matte Mainly used: - where resistance to abrasion is not a requirement. Pros: - Very easy to touch-up and does not accentuate surface defects Cons:- Easily marked and stained -G3 MPI Gloss Level 3 like an egg s shell Common usage walls, trim, doors and frames a good balance between durability and reflectance Pros: - Washability Cons:- Shows substrate defects -G5 MPI Gloss Level 5 Semi-Gloss Principal uses:- where washability and abrasion resistance properties are most important Pros: - Resistant to stains and dirt retention Cons:- Difficult to touch up -G6 MPI Gloss Level 6 - Gloss Principal uses:- not often used except where washability and abrasion resistance properties are of utmost importance and where the surface is very smooth Pros: - Ease of clean up Cons:- Highly light reflective and shows all substrate defects. INT 9.2E INT 9.2F INT 9.2G EPOXY ( TILE LIKE ) EPOXY, W.B. ( TILE LIKE ) Some public buildings and commercial buildings, such as restaurants, shops, and bars, where high traffic is anticipated, and detergent and industrial strength cleansers will be used on gypsum wall board and plaster walls require durable finishes, such as INT 9.2E or INT 9.2F epoxy systems. Both systems have excellent resistance to abrasion and marking. The solvent based system has better water and chemical resistance than the waterborne epoxy, and is recommended for use in areas subjected to these materials frequently. Where solvent fumes are a concern during application, such as renovations or additions to occupied buildings, INT 9.2F waterborne epoxy is preferred. MULTICOLOR Effect finishes, such as INT 9.2H multicolor, are used in both residential and commercial applications. The premium version of system INT 9.2H uses a clear, protective finish as the last coat to improve the abrasion, detergent and dirt resistance. The premium version is generally recommended for areas exposed to moderate traffic and abrasion.
3 Interior System 9.2 INT 9.2 PLASTER AND GYPSUM BOARD (GYPSUM WALLBOARD, DRYWALL, SHEET ROCK TYPE MATERIAL, & TEXTURE FINISHES, ETC.) Code Finishing System Coat Custom Grade Premium Grade MPI Product INT 9.2A LATEX (over latex sealer) 1 Latex Primer Sealer 50 (Gloss/Sheen as Specified) 2 Latex Latex 43,44,52, 53,54,114 3 Latex Latex 43,44,52, 53,54,114 INT 9.2B HIGH PERFORMANCE 1 Latex Primer Sealer Latex Primer Sealer 50 ARCHITECTURAL LATEX 2 HIPAC Latex HIPAC Latex 138,139,140,14 1 (Gloss/Sheen as Specified) 3 HIPAC Latex 138,139,140,14 1 INT 9.2C ALKYD (over latex sealer) 1 Latex Primer Sealer Latex Primer Sealer 50 (Gloss/Sheen as Specified) 2 Alkyd Alkyd 47,48, 49, 51 3 Alkyd 47,48, 49, 51 INT 9.2E EPOXY ( TILE LIKE ) 1 Latex Primer Sealer Latex Primer Sealer 50 2 Epoxy Epoxy 77 3 Epoxy 77 INT 9.2F EPOXY, W.B. ( TILE LIKE ) 1 Latex Primer Sealer Latex Primer Sealer 50 2 Epoxy Epoxy Epoxy 115 INT 9.2G MULTICOLOR 1 Primer Sealer Primer Sealer Multicolor Base Multicolor Base Coat Multicolor Pattern Coat Multicolor Pattern Coat Clear Coat 121 INT 9.2H FIRE RETARDANT Fire Retardant Coating (ULC Approved) 62 or 63 COATING (Clear or pigmented) These product, application procedures, and fire ratings differ from one manufacturer to another, and therefore it is recommended that these coatings be used in accordance with the manufacturer s instructions, and guarantee (if any). (Note: See) Evaluation) INT 9.2J W.B. FIRE RETARDANT Fire Retardant Coating (ULC Approved) 67 or 64 COATING These product, application procedures, and fire ratings differ from one manufacturer to another, and therefore it is recommended that these coatings be used in accordance with the manufacturer s instructions, and guarantee (if (Note: See) Evaluation) any).
4 Interior System Preparation 9.2 INT 9.2 PLASTER AND GYPSUM BOARD Remove sand, dust, dirt, oil, grease, wax, silicone, glue, and all other foreign matter. Any defects apparent before, and after, the primer coat has been applied shall not be the responsibility of the Painting Contractor. The resulting surface must be made acceptable to the Painting Contractor before application of the finish coat(s). Drywall Defects Many defects in the drywall substrate cannot be seen until after the primer, and in some cases, the intermediate coat, have been applied. This condition in drywall is not connected with the quality of either the paint or its application. In addition, structural deficiencies in studding and improperly applied drywall can cause other problems such as "nail popping", ridging, pinholes, etc. Latex primer sealers are flat in appearance, and deficiencies can be hard to detect, particularly under low lighting conditions. However, when materials with a slight to high gloss are applied, the deficiencies in the drywall are very noticeable. At this point, the drywall contractor should be obligated to correct all remaining imperfections. Joint Fillers The Painting Contractor should be cautious when painting drywall (gypsum board), as some of the new type of joint fillers on the market may have an alkali content too high for normal paint coatings. Some lightweight joint fillers are so porous, they require refilling, different filler, or the addition of an extra coat of sealer or finish coating, none of which was called for in the painting specifications. This should not be the financial responsibility of the Painting Contractor. Only top line primer sealers with excellent sealing properties must be used. Recycled paper, often used to produce drywall facings, may require additional preparation such as careful sanding and the application of an additional coat of primer sealer to eliminate suction spots etc. Stain blocking or alkyd based sealers may be required to block the leaching of water soluble materials occasionally found in recycled paper. Plaster Newly applied plaster must cure a minimum of 30 days at 75 F (24 C). The surface must then be tested for alkalinity (See 1.2 ph Testing). Wash and neutralize high alkali surfaces where they occur. Any imperfection in the plaster must be corrected by the plaster trade. Large holes, cracks, joints and other visible imperfections, must be corrected before surfaces will be accepted. Paint should not be applied until repaired surfaces are completely dry. After the application of the primer coat, fill minimal cracks, holes and imperfections, and sand smooth to match adjoining surfaces. Moisture readings must be taken to assure that no more then 12% moisture is in the plaster at the time of the coatings application. Porous areas that show suction spots must be double primed. Environmental conditions before and during application and during drying should be as outlined (See 1.1 Environment). Where plaster hot spots or questionably cured plaster surfaces are encountered, the use of an alkali resistant sealer, such as MPI #3, is recommended.
5 MPI Approved Product # 50 MPI #50 Interior Latex Primer Sealer A white, pigmented, waterborne latex sealer used on new interior plaster, concrete and gypsum wallboard surfaces that are subsequently painted with latex or alkyd finish coat(s). Its purpose is to reduce the porosity of the substrate for finish coats. Not intended for use on wood. [Evaluated characteristics include consistency/viscosity, dry time, fineness of grind, hiding power by contrast ratio method, reflectance, alkali resistance holdout properties, and sanding properties. See MPI Detailed Performance Specs for complete details, specific requirements, and/or reference specs.] MPI VOC Ranges (grams/l.) E3 <101 g/l E g/l E g/l Blanks may indicate information unavailable. Listing Brand Label Product Name Code E Range Benjamin Moore Moorcraft Latex Enamel Undercoater & Primer Sealer Benjamin Moore Regal First Coat Latex Primer & Undercoater California Paints CGI ProPrime Latex Primer White Cloverdale Paint Interior Latex Primer Sealer Color Wheel CGI Contractor's Choice Ti-Gard Interior Sealer Color Your World Latex Primer Columbia Paint CGI Premium Pro Interior Latex Enamel Undercoater PP 3 Columbia Paint CGI Insl-X Waterbase Primer/Sealer/Stain Killer AQ Coronado Paint Super Kote 5000 Latex Primer-Sealer Devoe/Fuller O'Brien Wonder-Tones Int. Vinly Latex Primer-Sealer DR Dunn-Edwards Eff-Stop Acrylic Masonry Primer/Sealer W Duron Inc. CGI Duron Paints Interior Acrylic Latex Undercoater Duron Inc. CGI Duron Paints Interior Acrylic Drywall Primer Farrell-Calhoun CGI Perfik-Seal Interior Latex Primer-Sealer 380 Flex Bon Paints CGI Interior Alkyd Latex Primer Frazee CGI Aqua Seal Interior Viyl Acrylic Wall Sealer General Paint CGI Breeze Super Seal Latex * 2 Glidden Paint Glidden Dulux Interior Latex Sealer Hirshfield's Paint CGI Drywall Primer Interior Latex ICI Dulux Paints Ultra Hide Interior Latex Wall Primer ICI Dulux Paints Dulux Ultra PVA Interior Primer Sealer Insl-x Aqualock Waterbase Primer/Sealer/Stain Killer AQ Iowa Paint CGI Prime Line Hi Hide PVA Primer Kelly-Moore Acry-Prime Interior Latex Primer/Sealer Kelly-Moore Enviro-Cote Interior Latex Primer Kwal-Howells CGI Accu-Pro Interior Latex Flat Drywall Primer Miller Paint CGI Kril Primer Sealer Mills Paint Superior Quality Interior Latex Primer Sealer Para Paints Prime Tech Hi-Hide Latex Primer 5799* 3 Porter Paints Painters' Friend Interior Latex Primer/Sealer Rodda Paint Scotseal Heavy Bodied Latex Sealer Sherwin Williams PrepRite Interior Latex Primer B28W200 3 Spectra-Tone CGI Jobmaster PVA Latex Primer Sealer 74 3 Tower Paint Interior Latex Sealer Vista Paint Seal Cote 155 3
6 MPI Approved Product # 44 MPI# 44 Interior Latex, Gloss Level 2 (a high side sheen flat, velvet-like ) Note: Requires a properly-prepared Level 4 drywall finish (i.e. assuming no critical lighting conditions). See "Recommended Levels of Drywall Finishing - GA " A white, or colored, waterborne latex-based paint with a low sheen finish. Used on primed/sealed interior plaster and gypsum board, and on primed wood and metals. [Gloss level must be a maximum of degrees and sheen 10 to degrees. Other evaluated characteristics include consistency/viscosity, dry time, fineness of grind, hiding power by contrast ratio method, reflectance, alkali resistance, flexibility, scrubbability, and sealing properties. See MPI Detailed Performance Specs for complete details, specific requirements, and/or references.] MPI VOC Ranges (grams/l.) E3 <101 g/l E g/l E g/l Blanks may indicate information unavailable. EPP is MPI EPP Rating which factors in Relative Category Performance & Gloss/Sheen Performance, OFP, and Appropriate Specified Use Listing Brand Label Product Name Code E EPP Benjamin Moore Moorcraft Super Spec Latex Eggshell Enamel Cloverdale Paint Interior Super Eggshell Acrylic Latex 032 Series 2 2 Color Wheel CGI Optima Satin Supreme Color Your World Designer's Touch Low Sheen Latex Eggshell Columbia Paint CGI Premium Pro Acry-Plus Velvet WB 1 1 Coronado Paint Tough Walls The True Latex Eggshell Enamel 34 Line Davis Frost CGI Davis Paint ProMax Interior Latex 3200 Series 1 1 Dunn-Edwards Suprema Interior Low Sheen Wall Paint W Duron Inc. CGI Ultra Delux Interior Acrylic Latex Low Sheen Enamel Farrell-Calhoun CGI Interior Premium Eggshell Enamel 370 Line Flex Bon Paints CGI Interior Satin Acrylic Wall & Trim Paint General Paint CGI Breeze Eggshell Latex General Paint CGI Premium Hi Hide Eggshell Latex Glidden Paint Ultra Int. Latex Eggshell Glidden Paint Glidden Dulux Acrylic Latex Eggshell Hirshfield's Paint CGI ProWall 1000 Top Scrub ICI Dulux Paints Dulux Professional Interior Latex Eggshell 1402 Series 3 3 ICI Dulux Paints Ralph Lauren Int. Satin Premium Acrylic Latex RL ICI Dulux Paints Dulux Ultra Eggshell Acrylic Int. Wall & Trim Enamel ICI Paints Canada CIL Professional - Int. Latex Eggshell Iowa Paint CGI Master Series Eggshell Enamel Kelly-Moore Sat-N-Sheen Interior Latex Low Sheen Finish Kelly-Moore Enviro-Cote Interior Latex Low Sheen Kwal-Howells CGI Accu-Tone Eggshell Interior Latex Enamel Miller Paint CGI Pro-Jex Eggshell Mills Paint Superior Quality Interior Eggshell Latex 1000 Series 3 3 Northern Paint Colorlox Int. Velvet Latex 43 Line 1 1 Para Paints Premium Interior Low Lustre Eggshell Para Paints Ultra Interior Eggshell Latex 8090* 2 2 Parker Paint CGI Pro Satin INTERIOR Latex Satin Gloss Enamel Porter Paints Painters' Friend Interior Latex Wall & Trim Paint PPG Speedhide Inerior Latex Egghsell Rodda Paint Master Painter Interior Pearl Lustre Latex X 3 3 Sherwin Williams Quali-Kote Interior Low Sheen Latex B20WQ Sherwin Williams ProMar 200 Interior Latex Eg-Shell B20W Spectra-Tone CGI Jobmaster Spectra-Tough Lo-Eggshell Enamel Tower Paint Premium Eggshell Latex Vista Paint Carefree Velva Sheen
7 MPI Approved Product # 138 MPI #138 High Performance Architectural Latex - Gloss Level 2 (a 'velvet-like' finish) Note: Requires a properly-prepared Level 4 drywall finish (i.e. assuming no critical lighting conditions). See "Recommended Levels of Drywall Finishing - GA " A high performance architectural latex coating, Gloss Level 2 (a 'velvet-like' finish). Designed to provide a significantly higher level of performance than conventional latex paints in the areas of scrub resistance, burnish resistance, and ease of stain removal. [Characteristics evaluated include gloss levels of maximum degrees and units at 85 degrees, hiding power, scrubbability, stain removal, burnish resistance, flexibility, and application properties. See MPI Detailed Performance Specs for complete details, specific requirements, and/or reference specs.] MPI VOC Ranges (grams/l.) E3 <101 g/l E g/l E g/l Blanks may indicate information unavailable. EPP is MPI EPP Rating which factors in Relative Category Performance & Gloss/Sheen Performance, OFP, and Appropriate Specified Use Listing Brand Label Product Name Code E EPP California Paints CGI Fresh Coat 100% Acrylic Latex Eggshell Enamel Cloverdale Paint Acrylic Kitchen & Bath Low Luster Enamel Devoe Fuller O'Brien AA Acrylic Interior Acrylic Eggshell FOB 212-XX 2 5 General Paint CGI Hi-Performance 2000 Eggshell ICI Dulux Paints Ultra Acrylic Interior Wall & Trim Enamel Northern Paint Colorlox Super Acrylic II Eggshell Enamel Sherwin Williams Superpaint Satin Latex
8 MPI Approved Product # 144 MPI #144 Institutional Low Odor/VOC Interior Latex - Gloss Level 2 (a 'velvet-like' finish) Note: Requires a properly-prepared Level 4 drywall finish (i.e. assuming no critical lighting conditions). See "Recommended Levels of Drywall Finishing - GA " A white or colored latex paint with low odor characteristics and a VOC of less than 10 grams per liter. For use in areas such as hospitals and other occupied buildings where the odor and VOC levels of conventional latex products would preclude their use. [Characteristics evaluated include gloss levels of maximum of degrees and sheen of units at 85 degrees, hiding power, scrubbability, alkali resistance, reflectance, flexibility and soil removal. See MPI Detailed Performance Specs for complete details, specific requirements, and/or reference specs.] MPI VOC Ranges (grams/l.) E3 <11 g/l Blanks may indicate information unavailable. EPR - Environmental/Performance Rating (VOC & Relative Performance of Category+Gloss & Appropriate Specified Use). L LEED level. Listing Mfr. Label Product Name Code E EPR L Cloverdale Paint Perfomance Plus Low Odor/Voc Eggshell Latex L ICI Paints (Canada) Dulux Inspirations Interior Acrylic Eggshell L ICI Paints (Canada) CIL Select - Int. Acrylic Eggshell L ICI Paints (Canada) Dulux Lifemaster Interior Acrylic Eggshell L Kelly-Moore Enviro-Cote Int.Acrylic Satin L Sherwin Williams Harmony Interior Latex Eg-Shell B9W L
9 Interior Substrates MPI Architectural Specification Manual INT 2.1 INT 3.1 INT 3.2 INT 3.3 INT 4.1 INT 4.2 INT 5.1 INT 5.2 INT 5.3 INT 5.4 INT 5.5 INT 5.6 INT 6.1 INT 6.2 INT 6.3 INT 6.4 INT 6.5 INT 6.6 INT 6.7 INT 6.8 INT 9.1 INT 9.2 INT 9.3 INT 10.1 INT 10.2 ASPHALT SURFACES (Zone/Traffic Marking on Interior Drive and Parking Areas, Etc.) CONCRETE VERTICAL SURFACES (Including Ceilings and Undersides of Mezzanines, Stairs, Etc.) CONCRETE HORIZONTAL SURFACES (Floors and Stairs, Etc.) CEMENTITIOUS COMPOSITION BOARD CLAY MASONRY UNITS (Including Pressed and Extruded Brick) CONCRETE MASONRY UNITS (CMU s) (Concrete Block and Concrete Brick) STRUCTURAL STEEL AND METAL FABRICATIONS (Columns, Beams, Joists, Etc.) STEEL - HIGH HEAT (Boilers, Furnaces, Heat Exchangers, Breeching, Pipes, Flues, Stacks, Etc.) GALVANIZED METAL (NOT CHROMATE PASSIVATED) High Contact/High Traffic Areas (Doors, Frames, Railings, Pipes, Etc.) Low Contact/Low Traffic Areas (Over-Head Decking, Pipes, Ducts, Etc.) ALUMINUM (NOT ANODIZED) COPPER STAINLESS STEEL (NOT POLISHED) GLUE LAMINATED BEAMS AND COLUMNS DIMENSION LUMBER (Columns, Beams, Exposed Joists, Underside Of Decking, Etc.) DRESSED LUMBER (Including Doors, Door And Window Frames, Moldings, Etc.) WOOD PANELING AND CASEWORK (Partitions, Panels, Plywood, Veneer, Millwork, Etc.) WOOD FLOORS AND STAIRS (Including Hardwood Flooring) WOOD SHINGLES AND SHAKES FIBERGLASS (Decorative Pats, Posts & Beams, Pipes, Etc.) PLASTIC (Trim, PVA, PVC, Plastic Lumber, Etc.) SPRAY TEXTURED CEILINGS PLASTER AND GYPSUM BOARD (Gypsum Wallboard, Drywall, Sheet Rock Type Material, & Texture Finishes, Etc.) ACOUSTIC PANELS AND TILES CANVAS AND COTTON COVERINGS (Pipe and Duct Coverings, Etc.) BITUMINOUS COATED SURFACES (Including Cast Iron Pipe, Concrete. Etc.)
10 Exterior Substrates MPI Architectural Specification Manual EXT 1.0 EXT 2.1 EXT 3.1 EXT 3.2 EXT 3.3 EXT 4.1 EXT 4.2 EXT 5.1 EXT 5.2 EXT 5.3 EXT 5.4 EXT 5.5 EXT 5.6 EXT 6.1 EXT 6.2 EXT 6.3 EXT 6.4 EXT 6.5 EXT 6.6 EXT 6.7 EXT 6.8 EXT 9.1 EXT 10.1 EXT 10.2 GENERAL ASPHALT SURFACES (Zone/Traffic Marking For Exterior Drive and Parking Areas, Game Lines, Etc.) CONCRETE VERTICAL SURFACES (Including Undersides of Balconies, Soffits, Etc.) CONCRETE HORIZONTAL SURFACES (Decks and Stairs, Parking Areas and Driveways, Game lines, Etc.) CEMENTITIOUS COMPOSITION BOARD (Cementitious Siding, Trims, Panels, Etc.) CLAY MASONRY UNITS (Pressed and Extruded Brick) CONCRETE MASONRY UNITS (CMU s) (Concrete Block and Concrete Brick) STRUCTURAL STEEL AND METAL FABRICATIONS (Columns, Beams, Joists, Etc.) STEEL - HIGH HEAT (Heat Exchangers, Breeching, Pipes, Flues, Stacks, Etc.) GALVANIZED METAL (NOT CHROMATE PASSIVATED) High Contact/High Traffic Areas (Doors, Frames, Railings, Pipes, Etc.) Low Contact/Low Traffic Areas (Over-Head Decking, Eavestroughs (gutters), Downpipes, Ducts, Etc.) ALUMINUM (NOT ANODIZED) (Sash, Sills and Frames, Flashing, Handrails, Posts and Railings, Downpipes, Etc.) COPPER (EXCLUDING ROOFS) STAINLESS STEEL (NOT POLISHED) GLUE LAMINATED BEAMS AND COLUMNS DIMENSION LUMBER (Columns, Beams, Exposed Joists, Underside of Decking, Siding, Fencing, Etc.) DRESSED LUMBER (Doors, Door and Window Frames, Casings, Battens, Smooth Fascias, Etc.) WOOD PANELING (Plywood Siding, Fascias, Soffits,, Etc.) WOOD DECKS AND STAIRS/STEPS (USING SPACED LUMBER) WOOD SHINGLE AND SHAKES (EXCLUDING ROOFS) FIBERGLASS (Panels, Trims, Fabrications, Etc. Includes Decorative Posts and Beams, Pipes, Etc.) PLASTIC (Fabrications, Vinyl Siding, Windows And Related Trims, ABS, PVA, and PVC Materials, Etc.) STUCCO (Walls and Soffits) CANVAS AND COTTON COVERINGS (Pipes, Ductwork, Etc.) BITUMINOUS COATED SURFACES (Cast Iron Pipes, Concrete, Etc.)
PART 1 - GENERAL. .2 Refer to the MPI Architectural Manual long form painting specification for guidance and spec notes when using this specification.
MPI Architectural Manual Page 1 of 15 PART 1 - GENERAL SPEC NOTES:.1 Use this guide specification when a short form specification is required to specify painting and decorating work on new, previously
More information1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.
PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials
More informationDAYTONA BEACH PIER BUILDING RESTORATION 06/10
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Steel. 2. Galvanized
More informationEducation Facility Guide Specification
Education Facility Guide Specification This Painting Schedule is furnished as a guide to select paint systems, and is not all-inclusive of available Sherwin-Williams products. Specifiers should review
More informationSECTION PAINTING Ultra Premium
SECTION 09 90 00 PAINTING Ultra Premium PART 3-EXECUTION 3.01 PREPARATION: A. Perform preparation and cleaning procedures in strict accordance with coating manufacturer s instructions for each substrate
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 09 - FINISHES
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Concrete. 2. Concrete
More information1. Adequate framing details, sizing, spacing and technical information shall be indicated on the documents.
DIVISION 9 - FINISHES 09100 - METAL SUPPORT SYSTEMS 1. Adequate framing details, sizing, spacing and technical information shall be indicated on the documents. 2. Fire-rated assemblies and acoustic rating
More informationA. Section includes surface preparation and application of wood finishes[.]
SECTION 09 93 00 - STAINING AND TRANSPARENT FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationInclude a paint or finish schedule on the drawings, listing colors, locations and types of materials.
DIVISION 09 - FINISHES Section 09900 - Painting Introduction This Section applies to exterior and interior areas or surfaces which are intended to receive a final field painted finish. Final painted finishes
More informationThe City of Winnipeg NEWPCC Lab Renovation
Bid Opportunity 253-2011 Page 1 of 6 Part 1 General 1.1 SUMMARY.1 Work under this contract includes, but is not necessarily limited to:.1 Surface preparation of substrates as required for acceptance of
More informationWe propose to use the following Dunn-Edwards paint material on the subject job (Section 09900).
April 10, 2007 Ed Soltero AIA Assistant Director Planning & Construction 3120 Sun Bowl Drive El Paso, TX 79968 Job: UTEP Gentlemen: We propose to use the following Dunn-Edwards paint material on the subject
More informationSECTION PAINTING. A. Surface preparation and field application of paints and coatings at interior and exterior surfaces.
SECTION 09910 PAINTING 1 PART ONE - GENERAL 1.1 COORDINATION A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification Sections apply
More informationSECTION PAINTS AND COATINGS
McClellan Blakemore Architects New Warehouse Facility for SECTION 09900 PAINTS AND COATINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints and stains. C. Scope:
More informationUBC Technical Guidelines Section Edition Painting and Coating Page 1 of 6
Page 1 of 6 1.0 GENERAL 1.1 Related UBC Guidelines.1 Section 09 00 10 Finishes General Requirements.2 Division 27 (Section 27 05 08 Cable Infrastructure Overview, 3.4.10; Section 27 05 05 Communication
More informationC. Surfaces to Receive Field Finishing: Areas shall be identified per project documents.
PART 1: GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Section, apply to this Section. 1.02
More informationSECTION PAINTS AND COATINGS. 1.3 REFERENCES A. ASTM D 16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications; 2000.
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Surface preparation. B. Field application of paints, stains, varnishes, and other coatings. C. See Schedule - Surfaces to be Finished, at end of Section. 1.2 RELATED
More informationSECTION PAINT. A. Section Cast-In-Place Concrete: Preparation of concrete wall assemblies to receive finishes.
SECTION 09910 PAINT PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Primer. B. Interior Paint. C. Exterior Primer. D. Exterior Paint. E. Wall Preparation. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place
More informationhigh-performance coatings for commercial spaces.
high-performance coatings for commercial spaces. for proven coating solutions that meet performance, aesthetic and environmental requirements just ask. matter what structure or substrate you re coating,
More informationCaulks & Sealants. Professional. Catalog
Caulks & Sealants Professional Catalog TM WeatherMaster Sealant Titebond WeatherMaster Sealant has been specifically formulated to outperform all other sealant technologies, including silicones, tripolymers
More informationA. Section includes surface preparation and the application of paint systems on interior substrates.
SECTION 09 91 23 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY
SECTION 099113- EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes sutface preparation and the application of paint systems on the following exterior substrates: 1. Clay masonry. 2.
More informationKNOWLEDGE EXPERIENCE SERVICE /MOO BuyLine 6067
KNOWLEDGE EXPERIENCE SERVICE 09 91 00/MOO BuyLine 6067 QUALITY COATING SOLUTIONS OUTSTANDING PERFORMANCE For more than 125 years, Benjamin Moore & Co. has consistently delivered paint products that define
More informationDESIGN GUIDELINES AND TECHNICAL STANDARDS
DESIGN GUIDELINES AND TECHNICAL STANDARDS Date of Issuance: January 1, 2014 DIVISION 9 FINISHES SECTION 09 2900 GYPSUM BOARD 1. General: This section outlines the requirements for gypsum board systems.
More informationA. Section includes surface preparation and the application of high-performance coating systems on the following substrates:
ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY
More informationSECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099600 - HIGH PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationThe Paint the Pros Use
History Independent Tradition HEADQUARTERED IN ROCKVILLE, MD, MCCORMICK PAINTS OPERATES 24 RETAIL STORES IN THE MID-ATLANTIC REGION OF THE U.S. WITH GROWING REACH AND INFLUENCE IN ALL SEGMENTS OF ARCHITECTURAL
More informationC. Wallboard shall not be glued directly to masonry or concrete walls below grade: provide furring.
09 0561 COMMON WORK RESULTS FOR FLOORING PREPARATION 09 0562 REMEDIAL FLOOR COATING 09 2116 - GYPSUM BOARD ASSEMBLIES A. Special consideration shall be given to the noise reduction characteristic and installation
More information2. In moist areas, portland cement plaster should be used if a more permanent material is not within budget limits.
UDIVISION 9 FINISHES 09 00 00 FINISHES 09 20 00 PLASTER AND GYPSUM BOARD PLASTER 1. Major partitions are to extend to underside of structure as required by code. Allow for structural deflection. Provide
More informationMold resistant, paperless gypsum board shall be used in bath, kitchen, and janitor locations.
09 00 00 - FINISHES 09 00 00 General Information CCU is continuing its investigation into preferred floor surface materials. In general, selection of floor materials should consider the environmental impact
More informationPlastering. Holiday Inn - Sultanate of Oman
1 208 Holiday Inn - Sultanate of Oman Gyproc GypFine Plasters provide the ultimate skimming solutions for today s high-end finish. They are formulated to suit a wide variety of backgrounds including plasterboard,
More informationINDUSTRIAL PAINTING SCHEDULE GUIDE
Copyright 2014, The Sherwin-Williams Company ISSUED May 2014 09 96 00- INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting
More informationCleaning and Protecting Concrete Surface Preparation, Application, and Inspection. NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc.
Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc. Cleaning and Protecting Concrete Surface Preparation, Application,
More informationSection GYPSUM DRYWALL
Section 09250 GYPSUM DRYWALL 1.00 GENERAL: A. Gypsum Association Specification GA216 and manufacturer's instruction (whichever is more stringent). 2.00 DRYWALL MATERIALS: A. Exposed Gypsum Board: ASTM
More informationEVERSHIELD THE #1 CHOICE OF PAINTING PROFESSIONALS. Ultra-Premium Exterior Paints EXTERIOR. Outperforms, Outlasts, Outshines.
A GREEN LEGACY, A GREENER FUTURE. As a paint contractor, your business depends on your reputation. That s why you choose quality paint to do the best possible job. Dunn-Edwards understands this. That s
More informationSATIN NON-DRIP ACRYLIC
PRODUCT DATA SHEET ISSUE DATE: FEBRUARY 2016 PRODUCT DESCRIPTION PRODUCT NAME PRODUCT DESCRIPTION SATIN NON-DRIP ACRYLIC A tough superior quality non-drip waterborne enamel with a satin sheen finish. A
More informationCopyright 2018, The Sherwin-Williams Company ISSUED MAY OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE
More informationCopyright 2014, The Sherwin-Williams Company. ISSUED June INTERIOR
Copyright 2014, The Sherwin-Williams Company ISSUED June 2014 09 91 23 - INTERIOR USGBC LEED-09 -NC/CI/CS NEW CONSTRUCTION, COMMERCIAL INTERIORS & CORE AND SHELL SPECIFICATION Contributes toward satisfying
More informationSherwin-Williams provides high-performance solutions that meet your requirements for aesthetics and durability.
A wide range of coating systems Ecotoner colorants, which do not add to the VOC of the paint. Only has color formulas provides Products are readily available at Your representative can provide a is committed
More informationMDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls
MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing
More informationCoastal Carolina University Design Guidelines FINISHES
09 00 00 - FINISHES 09 00 00 General Information CCU is continuing its investigation into preferred floor surface materials. In general, selection of floor materials should consider the environmental impact
More informationCopyright 2018, The Sherwin-Williams Company ISSUED MAY SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 - SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting
More informationGypsum Board Shaft-Wall Assemblies Gypsum board shaft-wall assembly for elevator and mechanical shafts over 2 stories.
09 00 00 - FINISHES 09 00 00 General Information Architects, in the design of project specific building systems, shall consider the unique characteristics of the generally hot-humid environment of Conway,
More informationPRODUCT PORTFOLIO PROFESSIONAL TRADE RANGE
PRODUCT PORTFOLIO PROFESSIONAL TRADE RANGE GUARANTEES *LIFETIME GUARANTEE Taubmans Endure is guaranteed against blistering, flaking or peeling if applied on suitable and properly prepared surfaces according
More informationOrangeburg County Sheriff s Department: Storage & K-9 Facility
SECTION 09900-1 INTERIOR, EXTERIOR AND INDUSTRIAL PAINTS AND COATINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior paint and coatings systems (LEED-09 NC/CI/CS Compliant) including surface preparation.
More informationSECTION EPOXY RESIN FLOORING
SECTION 09705 - EPOXY RESIN FLOORING PART 1 - GENERAL 1.1 SECTION INCLUDES A. Furnish all necessary material, labor and equipment required to prepare designated traffic areas and install quartz broadcast
More informationTnemec Standard Paint Schedule
Tnemec Standard Paint Schedule PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationArchitect s Supplemental Instructions
Architect s Supplemental Instructions Number: ASI 015 Date Issued: February 10, 2015 KPFF Project Number: 111145 Project: UW Montlake Triangle To Contractor, The Work shall be carried out in accordance
More informationWhite, a range of ready-mixed colours, and colours from the Dulux Colour System
TECHNICAL DATA SHEET Version 2 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior matt finish PRODUCT USES Recommended for exterior and
More informationFoil Back Gypsum Board
BRAND 09 29 00/NGC Foil Back Gypsum Board brand Foil Back Gypsum Board consists of a fire-resistant gypsum core with a heavy, natural finish and 100-percent recycled paper on the face and a strong liner
More informationUCSC Campus Standards Handbook Lath and Plaster Standards
DIVISION 9 FINISHES UCSC Campus Standards Handbook Lath and Plaster Standards 09200 1 SECTION 09200: LATH AND PLASTER STANDARDS I. GENERAL 1. Control joints shall be used to limit unbroken plastered areas
More informationPRODUCT LINE REVIEW TABLE OF CONTENTS
PRODUCT LINE REVIEW PRODUCT LINE REVIEW TABLE OF CONTENTS Section 1 Interior Primers 1A Interior Latex Primers Super Premium SEAL GRIP Interior/Exterior Acrylic Universal Primer/Sealer GRIPPER Interior/Exterior
More informationDIVISION 9 - FINISHES
09100 METAL SUPPORT SYSTEMS 09120 Ceiling Suspension Systems 09130 Wall/Partition Support Systems 09250 GYPSUM BOARD 09260 Gypsum Board Systems - Demountable 09300 TILE 09400 TERRAZZO 09500 ACOUSTICAL
More informationDryvit Interior Substrate Preparation
Dryvit products work well over a variety of substrates, for interior settings. This document will only discuss interior substrates and is not intended to be a technical discussion of substrate preparation,
More informationTechnical Data Sheet
ART OF COLOR EGGSHELL PAINT The Art of Color products line, because of the high quality of its raw materials, leaves a nice matte finish, while providing maximum performance. This coating has a low VOC
More informationVenger Electrostatic Coatings Master Specification Page 1
Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits
More informationSECTION PAINTING
SECTION 09 91 00 PAINTING PART 1 GENERAL 1.01 SUMMARY A. Provide: 1. Paint: a. Interior Substrates: 1) Concrete masonry units. 2) Precast concrete. 3) Gypsum drywall. 4) Ferrous and zinc-coated metal.
More informationGrainger Stadium Club Building Kinston, NC Dunn & Dalton Architects Project # GRS-17048
August 31, 2017 Grainger Stadium Club Building Dunn & Dalton Architects Project # GRS-17048 RECEIPT OF THIS ADDENDUM MUST BE NOTED ON THE BID FORM ADDENDUM NO.1 TO ALL BIDDERS: This Addendum supplements
More informationSECTION ROUGH CARPENTRY. B. AWPA (American Wood Preservers Association) Book of Standards. C. WCLIB (West Coast Lumber Inspection Bureau)
SECTION 06112 ROUGH CARPENTRY PART 1 GENERAL 1.01 REFERENCES A. APA (American Plywood Association) B. AWPA (American Wood Preservers Association) Book of Standards C. WCLIB (West Coast Lumber Inspection
More informationCopyright 2018, The Sherwin-Williams Company ISSUED MAY CARB SCM2007 EXTERIOR PAINTING THE SHERWIN-WILLIAMS COMPANY
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 91 13 CARB SCM2007 EXTERIOR PAINTING THE SHERWIN-WILLIAMS COMPANY COMMERCIAL PAINTING SPECIFICATION GUIDE This Painting Schedule is furnished
More informationDECORATIVE RE-IMAGINED CONCRETE FLOORS RESIDENTIAL COMMERCIAL
DECORATIVE C O A T I N G S RESIDENTIAL COMMERCIAL CONCRETE FLOORS RE-IMAGINED Table of Contents DECORATIVE COLOR Stone Tone Acid Stain... 3 Rembrandt Polymer Stain... 4 SINGLE COMPONENT SEALERS Stone Tone
More informationFaçade Architectural Wall Panel System - Guide Specification 3/11/2017 SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.
SECTION 09 7710 FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Decorative ½ / ¾ (13mm/19mm) thick prefinished panel with preengineered attachment clip along with hardware
More informationDECORATIVE RE-IMAGINED CONCRETE FLOORS RESIDENTIAL COMMERCIAL
DECORATIVE C O A T I N G S RESIDENTIAL COMMERCIAL CONCRETE FLOORS RE-IMAGINED Table of Contents DECORATIVE COLOR Stone Tone Acid Stain... 3 Rembrandt Polymer Stain... 4 SINGLE COMPONENT SEALERS Stone Tone
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationDECORATIVE RE-IMAGINED CONCRETE FLOORS RESIDENTIAL COMMERCIAL
DECORATIVE C O A T I N G S RESIDENTIAL COMMERCIAL CONCRETE FLOORS RE-IMAGINED Table of Contents DECORATIVE COLOR Stone Tone Acid Stain... 3 Rembrandt Polymer Stain... 4 SINGLE COMPONENT SEALERS Stone Tone
More information.1 Do Work to CSA A except where specified otherwise.
The City of Winnipeg Section 09250 Gypsum Drywall, Batt Insulation, and Air Vapour Barrier Page 1 of 4 PART 1 - GENERAL 1.2 REFERENCE STANDARDS.1 Do Work to CSA A82.31-1977 except where specified otherwise.
More informationCopyright 2018 The Sherwin-Williams Company ISSUED MAY OTC PHASE II INTERIOR PAINTING THE SHERWIN-WILLIAMS COMPANY
Copyright 2018 The Sherwin-Williams Company ISSUED MAY 2018 09 91 23 - OTC PHASE II INTERIOR PAINTING THE SHERWIN-WILLIAMS COMPANY COMMERCIAL PAINTING SCHEDULE GUIDE This Painting Schedule is furnished
More informationPART 1 - GENERAL. .2 Work under this Contract shall also include, but not necessarily be limited to:
Page 1 of 18 PART 1 - GENERAL.1 Use this specification section when a comprehensive specification is required to specify repainting over previously painted or finished interior surfaces..2 Review all requirements
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationADDENDUM A CONSTRUCTION SPECIFICATIONS
ADDENDUM A Description of Improvements: CONSTRUCTION SPECIFICATIONS The Improvements shall consist of constructing an approximate square foot single-family residence including car garage on the real property
More informationAPPLICATION INSTRUCTIONS REALSIDE TM
APPLICATION INSTRUCTIONS REALSIDE TM GENERAL INFORMATION: RealSide is a natural, real wood siding product designed for use in exterior cladding applications. RealSide is manufactured from hand selected,
More informationTEXAS DEPARTMENT OF HOUSING AND COMMUNITY AFFAIRS OFFICE OF COLONIA INITIATIVES TEXAS BOOTSTRAP LOAN PROGRAM. Form 15 Work Write-Up
TEXAS DEPARTMENT OF HOUSING AND COMMUNITY AFFAIRS OFFICE OF COLONIA INITIATIVES TEXAS BOOTSTRAP LOAN PROGRAM Form 15 Work Write-Up Owner-Builder Applicant Owner-Builder Co-Applicant Physical Address: City,
More informationWHATEVER THE CHALLENGE, PHILLIPS HAS YOU COVERED.
WHATEVER THE CHALLENGE, PHILLIPS HAS YOU COVERED. Build walls and ceilings with a strong base, sturdy reinforcements and much more with Phillips extensive line of high quality products. As a single source
More informationUniversity of Missouri St. Louis UMSL Project No. S Thomas Jefferson Library Elevator R&B Project No: Renovation & Repairs
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationMicrobarr Anti Bacterial Acrylic Eggshell
Microbarr Anti Bacterial Acrylic Eggshell Johnstone s Microbarr Anti Bacterial Acrylic Eggshell is a high performance, tough acrylic resin based interior coating, formulated to assist in the fight against
More informationVengerElectrostatic Coatings Master Specification Page 1
Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits
More informationAcrylitex Interior Texture and Coating Submittal Documentation
Acrylitex Interior Texture and Coating Submittal Documentation Project: Contractor: Installer: Supplier: John Wagner & Associates dba Grabber Construction Products 866-237-GRAB(4722) Distributor: Acrylic
More informationNOTE: Significant revisions or additions to the previous standards are highlighted in italics.
9 Finishes NOTE: Significant revisions or additions to the previous standards are highlighted in italics. GENERAL Designers shall verify that all applicable portions of these standards are incorporated
More informationIn the design development phase, submit finish and material selections to Facilities Management Planning Group for review.
09 00 00 FINISHES 09 01 00 Maintenance of Finishes 09 01 20 Maintenance of Plaster and Gypsum Board 09 01 20.91 Plaster Restoration 09 01 30 Maintenance of Tiling 09 01 30.91 Tile Restoration 09 01 50
More informationCustodian For : Villas at Lake Destiny 1010 Winderley Place Maitland, FL 32751
Custodian For : 1010 Winderley Place Maitland, FL 32751 Presented To: Ray or David Presented By: JEFFREY DECHURCH Sherwin-Williams (407) 468-9673 swrep4041@sherwin.com Page 1 Area Summaries Area Substrate
More informationFramed Decorative Panel Systems
Note: This document contains information and notes in hidden text. If you need assistance to view & hide text, instructions are at this link: http://www.marlite.com/hidden-notes-instructions.aspx Delete
More informationROCKGRIP UNIVERSAL ACRYLIC PVA
TECHNICAL DATA SHEET Version 1 2016 FEBRUARY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Matt finish for interior use PRODUCT USES Suitable for use on primed new or previously painted
More informationF.C.L. INTERIOR FINISHES CHECK LIST 2010 PRODUCT SELECTION - FLOORING GENERAL ITEMS PRODUCT SELECTION GENERAL ITEMS
INTERIOR FINISHES CHECK LIST 2010 Project: Project Number: Wil-Spec # This should not take long to go through, most questions below are listed as options, all you have to do is check off those answers
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationDIVISION 9 FINISHES. The Consultant shall consider the use of the space and long-term maintenance requirements in the selection of finishes
DIVISION 9 FINISHES GENERAL The Consultant shall consider the use of the space and long-term maintenance requirements in the selection of finishes D.C. Building Code and National Fire Protection Association
More informationRENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11
SECTION 09 29 00 GYPSUM BOARD 05/11 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text
More informationZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019
ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # 275-18 ADDENDUM NO. 3 April 02, 2019 This Addendum No. 3 ( Addendum ) is dated the date set forth above and modifies certain Bidding Documents issued
More informationComplementary Coatings Insl-x. Stix Bonding Primer Introduction
Complementary Coatings Insl-x Stix Bonding Primer Introduction Complementary Coatings: Insl-x Complementary Coatings Corporation is a wholly owned subsidiary of Benjamin Moore & Co Complete Specialty
More informationSECTION (09941) - TEXTURED FINISHING
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: SECTION 09 94 13 (09941) - TEXTURED FINISHING 1. Spray Applied Textured Finish and Primer a. Textured Finish for Ceilings. b. Textured Finish for Walls.
More informationTABLE OF CONTENTS DIVISION 1 GENERAL REQUIREMENTS
AIA General Conditions... GC-1 to GC-44 Amendments to General Conditions... AM-1 to AM-2 Supplements to General Conditions... SU-1 to SU-7 00200 Instructions To Bidders... 1 3 00201 Contractor s Bidding
More informationMarlite Guide Specification 2/24/2017 Surface Systems - MAP375 System SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.
Note: This document contains information and notes in hidden text. If you need assistance to view & hide text, instructions are at this link: http://www.marlite.com/hidden-notes-instructions.aspx Delete
More informationR-Matte Plus-3: Insulation for the Building Envelope
Attic and Crawl Space Applications R-Matte Plus-3 may be applied to the interior face of stud walls or roof rafters within attics and crawl spaces to provide a layer of continuous insulation (ci). Simply
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09 21 16 GYPSUM BOARD ASSEMBLIES PART 1- GENERAL 1.01 SUMMARY A. Provide gypsum board assemblies complete. 1.02 SUBMITTALS A. Comply with Section 01 33 00. B. Submit wall and ceiling texture samples,
More informationSECTION Arisfor WallGuard
1.1 GENERAL A. is a three component polymerized cementitious protective coating that can be applied to a variety of vertical interior and exterior substrates including: stucco, exterior gypsum sheathing,
More informationMargaret Greene Park Washroom Building 80 Westwood Road, Guelph, Ontario. Structural and Maintenance Remedial Work
SCOPE OF WORK Margaret Greene Park Washroom Building 80 Westwood Road, Guelph, Ontario Structural and Maintenance Remedial Work Prepared For City of Guelph City Hall, 1 Carden Street, Guelph, ON N1H 3A1
More informationE. Popcorn or other spray applied textures on ceiling or walls are not acceptable.
DIVISION 9 09 2000 GYPSUM BOARD ASSEMBLIES A. Drywall finish: Drywall finishing to conform to Level 5 finish in accordance with Association of Wall and Ceiling Industries (AWCI). Drywall MUST continue
More informationPRODUCT SELECTION GUIDE
PRODUCT SELECTION GUIDE Floor Sealers MasterTop 333 MasterKure 402 MasterKure 404 MasterTop 1116 Mastertop TC 406 Mastertop TC 450 Mastertop TC 471 Mastertop TC 495 Single Pack Two-pack Epoxy Polyurethane
More informationTechnical Data Sheet
MATTE CONTRACTOR CHOICE PAINT The Matte Contractor Choice C paint is designed for the contractor; it has good performance and opacity. No odor. Has very good brushability, leveling, durability, adhesion
More informationColorado Springs School District 11 Design & Construction Standards and Guideline Specifications Revision date: March 6, 2018
DIVISION 9 - FINISHES A. GENERAL Finishes and items listed below shall be minimum acceptable for area indicated. 1. Kitchen and toilet room walls and ceilings must be constructed of materials that will
More information