Normadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA

Size: px
Start display at page:

Download "Normadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA"

Transcription

1 Technical Data Normadur 65 HS PROPERTIES AND RECOMMENDED USAGE Paint type: NORMADUR 65 HS is a fast drying, flexible polyurethane coating with an aliphatic isocyanate curing agent. NORMADUR 65 HS is high-solid and contains rust preventing pigments. Typical uses: Normadur 65 HS can, in environmental classes C2 and C3, be used as a gloss and abrasion resistant single coat on easily painted steel products such as doors, gas bottles, hand rails, etc. It can also be used as a top coat in environmental classes C2-C4 and C5-I/M on various primers, and as a maintenance coating on old paint surfaces. Normadur 65 HS has good impact resistance and it can be piled after a short drying time. It can also be used as a floor coating on concrete and steel surfaces. It is very suitable also for wood, plywood, boards etc. Most common SFS-EN ISO systems: PUR 120/1-FeSa2½ A2.06 EPPUR 120/2-FeSa2½ A4.13 EPZn(R)PUR160/2-FeSa2½ A4.08 EPPUR 240/3-FeSa2½ A5I.05 EPZn(R)EPPUR 320/3-FeSa2½ Chemical resistance: Used in recommended paint systems, and correctly applied NORMADUR 65 HS withstands occasional splashes and spillage of water, oil and weak process chemicals. Weather resistance: Withstands sunlight and UV radiation. TECHNICAL DATA Volume solids: approx. 65 vol. % Total mass of solids*: approx. 890 g/l VOC value*: approx. 310 g/l *Values are calculated. Mixing ratio: Resin Cure 4 parts by volume 1 part by volume Pot life (+23 C): approx. 1 h after mixing Dryin times: 80 µm Surface dry To touch To recoat Fully cured +23 C 1,5 h 3 h 3 h 7 d NORMADUR 65 HS 1/5

2 Calculated theoretical coverage and recommended film thickness: Dry Wet Coverage 60 µm 90 µm 11,1 m 2 /l 80 µm 125 µm 8,2 m 2 /l 120 µm 185 µm 5,4 m 2 /l 150 µm 230 µm 4,3 m 2 /l Practical coverage: Depends on wind conditions, the structure to be painted, the roughness of the surface and the application method. Practical coverage on concrete surfaces: Priming Top coating 4-7 m 2 /l 4-9 m 2 /l Depends on method of application and the porosity of the surface. For exceptionally porous surfaces priming twice is recommended. Colour: NCS-, RAL-, KY-, SSG-colours with limitations. Thinner: OH 10, OH 17, OH 66 (slow) Cleaner: OH 17 Roller thinner: OH 12 Finish: Semi gloss (gloss if lacquered with Normadur Clear) APPLICATION INSTRUCTIONS Surface preparations: All solid impurities that could prevent adhesion should be removed from the old surfaces. Remove salts and other water soluble impurities by wet cleansing with brush, high pressure-, steam- or alkali cleansing. Remove grease and oils by alkali-, emulsion- or solvent cleansing (SFS-en ISO , SFS-EN ISO ). The surfaces should be rinsed carefully with fresh water after clensing. Old, painted surfaces, in which maximum overcoating interval has expired, additional roughening with suitable method is recommended. Steel surfaces: Blast cleanin to a min. of Sa 2½ (SFS-ISO , SFS-EN ISO ). Cold rolled plates must be roughened with abrasive paper. Shop primed steel surfaces: Damaged or corroded surfaces should be blast cleaned to a grade of Sa 2½ (SFS-ISO , SFS-EN ISO ). Aluminium surfaces: Remove grease and other contaminants. Sand sweeping before painting improves adhesion. Normadur 65 HS does not adhere to marine aluminium without primer. NORMADUR 65 HS 2/5

3 Galvanised surfaces: Remove grease, oil and dirt with alkali-, emulsion- or solvent cleaning (SFS-EN ISO ). Hot dip galvanised steel surfaces are to be thoroughly sweep blast cleaned with fine abrasive. Galvanised thin steel plates should be washed with a 5 % ammonia solution followed by fresh water hosing. All galvanised and hot dip galvanised steel surfaces should be roughened and primed with EPOCOAT 21 PRIMER. New concrete surface: The concrete must be dry and at least 4 weeks old, and humidity no more than 97 % (4 % by weight). The floor humidity can be tested if a humidity gauge is not available by using a rubber mat. The colour of the floor under the rubber mat must not be darker than the rest of the floor after a 24 hour test. The concrete must be hard and strong enough (at least 80% of the final strength) and additives such as melamine resins, silicones or silicates that might decrease the adhesion or absorption of the coating must not be used. Loose concrete, laitance, residues of plastic dispersions and waxes should be removed from the concrete surface with abrasive blasting or grinding. If required a % hydrochloric acid solution could be used. Previously painted epoxy coating: Grease and oil should be removed by emulsion cleaning. Surfaces should be roughened down by grinding. Holes and cracks must be filled with a epoxy filler. Old concrete surface: Grease and other dirt is removed from uncoated surfaces by emulsion cleaning. Grease removal can be made more effective by flame cleaning. An old coating or laitance is removed by sand blasting, milling or grinding. Holes and cracks must be filled with a epoxy filler. Other methods as for New concrete surfaces. Asphalt surface: Asphalt shoud be over 6 months old, dry and clean. Primer on steel surfaces: EPOCOAT 21 PRIMER, EPOCOAT 21 HB, NORMAZINC SE, NORECOAT FD PRIMER, NORMADUR HB, NORMASTIC 405, PENGUARD EXPRESS Top coat: NORMADUR 65 HS, NORMADUR CLEAR Environmental conditions during application: The surface should be dry and clean. During application and drying time the temperature of the paint, air, and surface should be above 5 C and the relative humidity below 80 %. The surface tem-perature should be min 3 C above the dew point of the air. Method of application: Use an airless spray, electrostatic spray or brush. On concrete surfaces use roller. Stir the resin and cure separately and then mix both components thoroughly. The mixing ratio is 4:1 (resin:cure) by volume. If needed 5-15 % thinner (OH 66 or OH 17 or OH 10) may be added. When using a roller, use thinner (OH 12) 5-10 %. Use a high-pressure airless spray with a nozzle tip of 0.011" " orifice. Don t use an adjustable spraying nozzle. The spray angle depends on the object to be painted. In order to ensure the best possible performance of the product, it is recommended that the paint is at room temperature before the application. Priming (concrete surfaces): Thinned paint should be spread on the floor with a steel spreader, mohair roller or a paint brush. If absorption is insufficient, it can be improved after 8 hours (+23 C). On a porous or new concrete surface the priming is performed with Normafloor 105 epoxy primer. NORMADUR 65 HS 3/5

4 Top coating (concrete surfaces) The application of the coating is recommended to make within 8 h 3 days after priming (+23 C). The top coating is applicated with 5-10 % thinned Normadur 65 HS. Normadur 65 HS should be spread with a fine mohair roller, roller or a paint brush. Storage and shelf life: The product must be stored in original sealed containers at temperatures from 5 C to 30 C. The storage conditions are to keep the containers in a dry, well ventilated space away from source of heat and ignition. When stored as described above, the unopened component A will keep up to 2 years and unopened component B to 1,5 years from the date of manufacture. The date of manufacture is indicated in the label of the paint can as a batch date. CE marking: 0416 Nor-Maali Oy Vanhatie Lahti, Finland Declaration of performance No. NOR CPR-7826 EN :2004 Surface protection products - Coating Physical resistance (5.1) Abrasion resistance Weight loss < 3000 mg Capillary absorption and w < 0,1 kg/m 2 h 0,5 permeability to water Impact resistance Class II: 10 Nm Adhesion strength by 2,0 N/mm 2 pull-off test Dangerous substances See safety data sheet NORMADUR 65 HS 4/5

5 Safety: Please follow the environmental and safety instructions displayed on the container and Safety Data Sheet. Use under well ventilated conditions. Do not breathe or inhale mist, use respirator mask. Avoid skin contact. Spillage on the skin should immediately removed with suitable cleanser, soap or water. In case of contact with eyes, rinse immediately with plenty of clean water and if necessary seek medical advice. DISCLAIMER: The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, as the paint is often used under conditions beyond our control, we cannot guarantee anything but the quality of the paint itself. We reserve the right to change the given data without notice. Please contact our office for more specific information. Technical Data Sheet 3/14 Sales in Finland NOR-MAALI Oy Vanhatie Lahti tel myynti@nor-maali.fi NORMADUR 65 HS 5/5

1(5) Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated.

1(5) Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated. 1(5) A two-component, resin modified epoxy paint. Excellent resistance to abrasion, chemicals and water immersion Used as a primer or finish for interior and exterior steel, aluminium and zinc surfaces

More information

Concrete Paint and Varnish

Concrete Paint and Varnish www.teknos.com DATA SHEET 1247 12 22.02.2017 TEKNOFLOOR AQUA 110F Concrete Paint and Varnish PAINT TYPE USAGE SPECIAL PROPERTIES TEKNOFLOOR AQUA 110F Concrete Paint is a water-based, two-pack epoxy paint.

More information

Property Test/Standard Description

Property Test/Standard Description Other Technical Data Sheet 24100;24120;26200 1 24100 VValidationDate). 1 Product description This is a two component, anticorrosive water borne epoxy coating. It is a versatile, fast drying product containing

More information

TECHNICAL DATA SHEET

TECHNICAL DATA SHEET Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description Approved 24640;24680 1 24640 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. This product is LEED compliant and contains no solvents on the Hazardous Air

More information

Approved. Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 29 C IED (2010/75/EU) (calculated)

Approved. Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 29 C IED (2010/75/EU) (calculated) Approved 15261;15962 1,2 15962 epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy coating. It is a surface tolerant, high solids product. This product is tintable

More information

Property Test/Standard Description

Property Test/Standard Description Approved 21060;21061 1,2 21060 epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy coating. It is a surface tolerant, high solids, high build product. Will continue

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 25 C calculated IED (2010/75/EU) (theoretical)

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 25 C calculated IED (2010/75/EU) (theoretical) Approved 618;612 1,2 618 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. It is a zinc phosphate pigmented, high build product.

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C VOC-USA / VOC Hong Kong EPA Method 24 Other Technical Data Sheet 2920;2401 1 2920 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids,

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24 Other Technical Data Sheet 27800;27801 1 27800 VValidationDate). 1 Product description This is a two component amine cured pure epoxy coating. It is a fast drying, high solids, high build product. It provides

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 35 C

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 35 C Other Technical Data Sheet 13640;13641 1 13640 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is an ultra high build, high solids abrasion resistant

More information

Protective: Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel.

Protective: Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Other Technical Data Sheet 15261;15962;15280 1 15962 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is a surface tolerant, high solids product.

More information

two component polyamide cured epoxy primer yellow/green - eggshell

two component polyamide cured epoxy primer yellow/green - eggshell 6 pages Revision of December 006 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 0 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

Pre-qualification testing in accordance with NORSOK M-501, Rev. 3, System 7, suitable for splash zone. Property Test/Standard Description

Pre-qualification testing in accordance with NORSOK M-501, Rev. 3, System 7, suitable for splash zone. Property Test/Standard Description Other Technical Data Sheet 574;576 1,2 574 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is a high solids, high build, glass flake reinforced product.

More information

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β Product Description Neopox Special is a two-component solvent-based epoxy paint suitable for use on construction, metallic & GRP surfaces that undergo significant mechanical stress and need chemical resistance.

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 2401;3440 1 3440 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product.

More information

GULF COAST PAINT MFG., INC

GULF COAST PAINT MFG., INC MCU-100 PRIMER/FINISH MOISTURE CURED URETHANE ALUMINUM COATING PRODUCT DESCRIPTION A one component, Moisture Cured Polyurethane Aluminum Coating. Has excellent adhesion to sound, tightly adherent rusty

More information

Protective: Recommended for refineries, power plants, bridges and buildings. Suitable for a wide range of industrial structures.

Protective: Recommended for refineries, power plants, bridges and buildings. Suitable for a wide range of industrial structures. Approved 11480 1,2 11480 acrylic ^(ValidationDate) 1 Product description This is a one component physically drying acrylic coating. It has a semi gloss finish with good gloss retention. It is fast drying.

More information

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C

Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 32 C Approved 18420;18360 1,2 18420 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured, glass flake reinforced, abrasion resistant epoxy coating. It is a surface tolerant, high

More information

Property Test/Standard Description

Property Test/Standard Description Approved 612;617 1,2 617 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. Designed as a primer for new construction. Can be used

More information

HAMMERITE NO. 1 RUST BEATER PRIMER

HAMMERITE NO. 1 RUST BEATER PRIMER TECHNICAL DATA SHEET Version 2 2018 June THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Hammerite No.1 Rust Beater provides a high build finish to heavily pitted areas of rust and

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 2401;3440 1,2 3440 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high

More information

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell 5 pages Revision of September 2009 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

SIGMAZINC 160. Revision of March 2007 DESCRIPTION. two component moisture curing inorganic zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS

SIGMAZINC 160. Revision of March 2007 DESCRIPTION. two component moisture curing inorganic zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS 5 pages Revision of March 2007 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C Other Technical Data Sheet 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 200 C and can

More information

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β Product Description Neopox Special is a two-component solvent-based epoxy paint suitable for use on construction, metallic & GRP surfaces that undergo significant mechanical stress and need chemical resistance.

More information

Property Test/Standard Description

Property Test/Standard Description Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant up to 600 C. Can be used as primer,

More information

Property Test/Standard Description

Property Test/Standard Description Approved 32222;32223;35142 1 32222 epoxy composite ^(ValidationDate) 1 Product description This is a two component glass flake reinforced epoxy composite coating. It is heat resistant up to 250 C (482

More information

Property Test/Standard Description STANDARD GRADE

Property Test/Standard Description STANDARD GRADE Other Technical Data Sheet 4860;523;527;1549 1,2 523 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids,

More information

Property Test/Standard Description

Property Test/Standard Description Approved 2920;2401 1 2920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

Property Test/Standard Description

Property Test/Standard Description Approved 1505;1506 1,2 1505 phenolic/novolac epoxy ^(ValidationDate) 1 Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 C (401

More information

Property Test/Standard Description

Property Test/Standard Description Approved 29560;29561 1 29560 zinc silicate ^(ValidationDate) 1 Product description This is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description Approved 35682;35683 1 35682 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids product. Can be used

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested)

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method C calculated VOC-US/Hong Kong. US EPA method 24 (tested) Approved 28780 1,2 28780 acrylic ^(ValidationDate) 2 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior use.

More information

Property Test/Standard Description. 53± 2 % matt (0-35) Flash point ISO 3679 Method 1 25 C calculated IED (2010/75/EU) (theoretical)

Property Test/Standard Description. 53± 2 % matt (0-35) Flash point ISO 3679 Method 1 25 C calculated IED (2010/75/EU) (theoretical) Approved 7081;7243 1,2 7243 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a fast drying, high zinc containing product. It conforms

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (32 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (32 C) calculated VOC-US/Hong Kong Approved 2920;2401 1 2920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.

Pre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C. Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

Property Test/Standard Description Solids by volume. ISO 3233 Gloss level (60 ) ISO 2813

Property Test/Standard Description Solids by volume. ISO 3233 Gloss level (60 ) ISO 2813 Other Technical Data Sheet 2063;2064 1,2 2063 epoxy VValidationDate). 1 Product description This is a two component solvent free polyamine cured epoxy coating. It is a general purpose tank lining with

More information

Marine: Exterior and interior areas, including outside hulls, superstructures, decks, cargo holds and water ballast tanks.

Marine: Exterior and interior areas, including outside hulls, superstructures, decks, cargo holds and water ballast tanks. 478;479;4060 1,2 478 epoxy VValidationDate). 1 Product description This is a two component amine cured pure epoxy coating. It is a fast drying, abrasion resistant, high solids, high build product. Designed

More information

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4 Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong Approved 20940;16620 1 20940 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 7461;7680 1 7680 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It conforms

More information

Property Test/Standard Description STANDARD GRADE

Property Test/Standard Description STANDARD GRADE Other Technical Data Sheet 525;527;1549 1,2 525 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids,

More information

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It

More information

Approved. Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. semi gloss (35-70) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong Approved 620;621 1 620 epoxy ^(ValidationDate) 1 Product description This is a two component, polyamide cured, high molecular weight epoxy coating. Specially designed as a tie coat/ sealer on top of inorganic

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards.

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Approved 16480;18120 1,2 16480 polyurethane ^(ValidationDate) 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a high gloss finish with very

More information

Approved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-US/Hong Kong. US EPA method 24 (tested)

Approved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-US/Hong Kong. US EPA method 24 (tested) Approved 25760;26000 1,5 25760 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured solvent free epoxy coating. It is a high performance product. It is a self smoothing, easy

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (33 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (33 C) calculated VOC-US/Hong Kong Approved 24760;24700 1 24760 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. This product is LEED compliant and contains no solvents on the Hazardous Air

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description Approved 25780 1 25780 acrylic ^(ValidationDate) 1 Product description This is a one component waterborne acrylic thin film intumescent coating. Independently tested and approved for fire protection of

More information

Property Test/Standard Description

Property Test/Standard Description Approved 1537 1,2 1537 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. It is a fast drying, high build, zinc phosphate pigmented product. Can be

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards.

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Approved 12660 1,2 12660 Acrylic emulsion ^(ValidationDate) 1 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior

More information

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell 5 pages Revision of July 2005 DESCRIPTION two component polyamide cured epoxy primer PRINCIPAL CHARACTERISTICS general purpose epoxy primer in protective coating systems for steel and non ferrous metals

More information

Property Test/Standard Description

Property Test/Standard Description Approved 34642;34643 1 34642 multipolymeric matrix ^(ValidationDate) 1 Product description This is a two component titanium catalyzed inorganic ceramic copolymer. It complies to the generic type Multi

More information

Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-EU EU VOC Directive 2004/42/CE (theoretical) 14 g/l

Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method C VOC-EU EU VOC Directive 2004/42/CE (theoretical) 14 g/l Approved 29980;29981;30062 1,5 29980 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured solvent free epoxy coating. It is a high performance product. It is easy to apply.

More information

SIGMAZINC 158. Revision of September 2008 DESCRIPTION. two component moisture curing zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS

SIGMAZINC 158. Revision of September 2008 DESCRIPTION. two component moisture curing zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS 5 pages Revision of September 2008 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 343 1,2 343 alkyd ^(ValidationDate) 1 Product description This is a one component oxidatively drying alkyd coating. Can be used as primer or mid coat in atmospheric environments. Suitable for

More information

General: Primarily designed for maintenance and repair. Only aluminium containing versions to be used in immersed environments.

General: Primarily designed for maintenance and repair. Only aluminium containing versions to be used in immersed environments. Other Technical Data Sheet 5580;5660;6520;10760 1,2 5580 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high

More information

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β

Mosaic 100gr/m 2 /layer 125gr/m 2 /layer Ceramic Tiles 100gr/m 2 /layer 125gr/m 2 /layer Cementitious high porosity. Gloss 75Α:25Β Product Description Neopox Special is a two-component solvent-based epoxy paint suitable for use on construction, metallic & GRP surfaces that undergo significant mechanical stress and need chemical resistance.

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 23660 1,2 23660 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is an aluminum pigmented product. It is heat resistant

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 16561;16840;18880 1,2 18880 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high

More information

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 23680;1551 1,2 23680 epoxy mastic ^(ValidationDate) 1 Product description This is a two component amine cured epoxy mastic coating. It is a surface tolerant, high solids product. It is aluminum

More information

Property Test/Standard Description. 96± 2 % matt (0-35) Flash point ISO 3679 Method 1 34 C

Property Test/Standard Description. 96± 2 % matt (0-35) Flash point ISO 3679 Method 1 34 C Approved 388;26160 1,2 388 unsaturated polyester ^(ValidationDate) 1 Product description This is a glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely abrasion resistant

More information

Technical Data Chemflake Special

Technical Data Chemflake Special Technical Data Chemflake Special Product description A high build glass flake reinforced vinyl ester coating, specially designed for high temperature service. Recommended use Steel in aggressive environments.

More information

Property Test/Standard Description

Property Test/Standard Description Approved 515;519;527;1549 1,2 515 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.

More information

2013 Product Catalogue

2013 Product Catalogue 2013 Product Catalogue We Change Chemistry Of The Structure. The quality of the materials used in building and construction areas are also increasing and as a result, lifting our standarts of living to

More information

SIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation

SIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation 5 pages DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading rate Touch dry after Overcoating

More information

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss >4% <70% 83mg IR4

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss >4% <70% 83mg IR4 Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor P is a suitable screed that can be applied on cement-based floors which need high mechanical

More information

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description

Tested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It

More information

Approx. 12 m² per litre depending on surface porosity, profile. Application methods

Approx. 12 m² per litre depending on surface porosity, profile. Application methods TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Versatile multi-surface waterborne primer PRODUCT USES Suitable for use as a primer to appropriately

More information

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 2124;7720 1,2 7720 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc epoxy coating. It provides corrosion protection as part of a complete coating

More information

Date of issue: 5 October 2017 Page: 1/6

Date of issue: 5 October 2017 Page: 1/6 Approved 16560;16561;16840 1,2 16560 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high

More information

A range of popular roof shades Spruce Acrylic Roof cannot be tinted.

A range of popular roof shades Spruce Acrylic Roof cannot be tinted. TECHNICAL DATA SHEET Version 1 2017 MARCH THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A quality, 100% pure acrylic paint for roofs PRODUCT USES Spruce Acrylic Roof is for application

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C calculated IED (2010/75/EU) (theoretical)

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C calculated IED (2010/75/EU) (theoretical) Approved 10680;2401 1 10680 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high

More information

Technical Data Baltoflake

Technical Data Baltoflake Technical Data Baltoflake Product description A quick curing, high build, abrasion resistant glass flake reinforced polyester coating, that gives long time corrosion protection. Recommended use Steel structures

More information

PU Anti Graffiti Polyurethane Finish

PU Anti Graffiti Polyurethane Finish PRODUCT DESCRIPTION A two pack, aliphatic anti graffiti acrylic polyurethane INTENDED USES Used as a highly durable finish coat with excellent obliteration properties for exterior of tanks, equipment,

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 392 F (200 C) and can be applied on hot

More information

Approved. This product is tintable in a wide range of colours in Jotun's Multicolor Decorative (MCD) system. Property Test/Standard Description

Approved. This product is tintable in a wide range of colours in Jotun's Multicolor Decorative (MCD) system. Property Test/Standard Description Approved 12660 1,2 12660 Acrylic emulsion ^(ValidationDate) 1 Product description This is a one component water borne acrylic emulsion coating. It is a versatile, fast drying product for exterior and interior

More information

AMERLOCK 2 AL. PRODUCT DATA SHEET September 12, 2018 (Revision of May 2, 2018) DESCRIPTION. Fast Dry Aluminum Epoxy Mastic Coating

AMERLOCK 2 AL. PRODUCT DATA SHEET September 12, 2018 (Revision of May 2, 2018) DESCRIPTION. Fast Dry Aluminum Epoxy Mastic Coating DESCRIPTION Fast Dry Aluminum Epoxy Mastic Coating PRINCIPAL CHARACTERISTICS Fast drying properties Good drying properties even at low temperatures Low VOC High performance coating for new or old steel

More information

max g/l (approx. 1.9 lb/gal) (aluminum) 31.2 m²/l for 25 µm (1251 ft²/us gal for 1.0 mils)

max g/l (approx. 1.9 lb/gal) (aluminum) 31.2 m²/l for 25 µm (1251 ft²/us gal for 1.0 mils) DESCRIPTION Two-component, engineered polysiloxane clearcoat PRINCIPAL CHARACTERISTICS Universal clear finish compatible with primed steel, clean metals and concrete High durability in challenging environments

More information

Pre-qualification testing in accordance with NORSOK M-501, Rev. 3/4, System 7, suitable for splash zone. Property Test/Standard Description

Pre-qualification testing in accordance with NORSOK M-501, Rev. 3/4, System 7, suitable for splash zone. Property Test/Standard Description Approved 390;21780;21840 1,2 390 unsaturated polyester ^(ValidationDate) 1 Product description This is a styrene free glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely

More information

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description

This product contributes to the Green Buildings Standard credits. Please see section Green Building Standards. Property Test/Standard Description Approved 36962 1 36962 vinyl ^(ValidationDate) 1 Product description This is a one component waterborne acrylic thin film intumescent coating. Independently approved for fire protection of structural steel

More information

Property Test/Standard Description

Property Test/Standard Description Approved 525;527;1549 1,2 525 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.

More information

Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24 Other Technical Data Sheet 3140;3240;4320 1,2 3140 polyurethane VValidationDate). 1 Product description This is a two component chemically curing aliphatic acrylic polyurethane coating. It has a gloss

More information

General: Primarily designed for maintenance and repair. In immersed environments Jotamastic 80 Aluminium is suitable.

General: Primarily designed for maintenance and repair. In immersed environments Jotamastic 80 Aluminium is suitable. Approved 5580;5660;6520 1,2 5580 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids product. Specially

More information

Technical Data Jotamastic 80 MIO

Technical Data Jotamastic 80 MIO Technical Data Jotamastic 80 MIO Product description Jotamastic 80 MIO is a high solids two-pack micaceous iron oxide pigmented, surface-tolerant epoxy mastic coating which can be applied in low film thickness.

More information

Hardener: at least 24 months when stored cool and dry

Hardener: at least 24 months when stored cool and dry DESCRIPTION Two-component, engineered siloxane coating PRINCIPAL CHARACTERISTICS Unique, high gloss, engineered siloxane Virtually HAPs free, ultra-low VOC High durability in challenging environments Tough

More information

PRODUCT DATA SHEET Sika Unitherm Platinum-120

PRODUCT DATA SHEET Sika Unitherm Platinum-120 SOLVENT-FREE, ULTRA HIGH BUILD, 2-PACK, MODIFIED EPOXY BASED INTUMESCENT FIRE PRO- TECTION COATING FOR INTERNALLY OR EXTERNALLY EXPOSED STRUCTURAL STEEL DESCRIPTION is a solvent-free, 100 % solids, 2-pack,

More information

Approved. Property Test/Standard Description STANDARD GRADE. semi gloss (35-70) Flash point ISO 3679 Method 1

Approved. Property Test/Standard Description STANDARD GRADE. semi gloss (35-70) Flash point ISO 3679 Method 1 Approved 4860;523;527;1549 1,2 523 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product.

More information

Approved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong. US EPA method 24 (tested)

Approved. Property Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1 25 C calculated VOC-US/Hong Kong. US EPA method 24 (tested) Approved 612;625;627 1,2 625 epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured epoxy coating. It has a glossy finish with fair gloss retention. To be used as topcoat

More information

Sikafloor -264 is a two part, economic, solvent-free coloured epoxy resin, suitable for use under hot climate condition.

Sikafloor -264 is a two part, economic, solvent-free coloured epoxy resin, suitable for use under hot climate condition. Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -264 2-part epoxy roller and seal coat Construction Product Description Sikafloor -264 is a two part, economic, solvent-free coloured

More information

vinyl ester Property Test/Standard Description semi gloss (35-70) Flash point ISO 3679 Method 1 34 C calculated IED (2010/75/EU) (theoretical)

vinyl ester Property Test/Standard Description semi gloss (35-70) Flash point ISO 3679 Method 1 34 C calculated IED (2010/75/EU) (theoretical) Approved 408;21800;21820;21740;21760;21840 1,2 408 ^(ValidationDate) 1 Product description This is a glass flake reinforced coating. It is an ultra high build, extremely chemical resistant and fast curing

More information

3-component epoxy self-smoothing screed

3-component epoxy self-smoothing screed Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data

More information

Construction. Two-part Epoxy Roller and Seal Coat. Product Data Sheet Edition No. 01 (October 2015) Sikafloor -264 HC. Product Description

Construction. Two-part Epoxy Roller and Seal Coat. Product Data Sheet Edition No. 01 (October 2015) Sikafloor -264 HC. Product Description Product Data Sheet Edition No. 01 (October 2015) Two-part Epoxy Roller and Seal Coat Construction Product Description is a two part, economic, solvent-free colored epoxy resin. Uses Roller coat for concrete

More information

Property Test/Standard Description

Property Test/Standard Description Approved 18940;18941 1,2 18940 acrylic ^(ValidationDate) 1 Product description This is a two component chemically curing modified acrylic coating. The product does not contain isocyanates, neither does

More information

AMERLOCK 2 / SIGMACOVER 2

AMERLOCK 2 / SIGMACOVER 2 DESCRIPTION Two-component, high solids epoxy coating PRINCIPAL CHARACTERISTICS Low-temperature curing down to 0 C (32 F) High performance self priming universal epoxy High solids, low VOC Surface tolerant

More information

Epoxol Floor. Two component solvent-free epoxy system for creation of self-levelling floors. Fields of Application. Properties/ Advantages

Epoxol Floor. Two component solvent-free epoxy system for creation of self-levelling floors. Fields of Application. Properties/ Advantages Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor is a suitable screed that can be applied on cement-based floors which need high mechanical

More information

SIGMAZINC 158. PRODUCT DATA SHEET January 7, 2015 (Revision of December 15, 2014) DESCRIPTION

SIGMAZINC 158. PRODUCT DATA SHEET January 7, 2015 (Revision of December 15, 2014) DESCRIPTION DESCRIPTION Two-component, moisture-curing zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS Certificate for ASTM A-490 class 'B' for slip coefficient Complies with the compositional requirements

More information

Property Test/Standard Description. Flash point ISO 3679 Method C

Property Test/Standard Description. Flash point ISO 3679 Method C Other Technical Data Sheet 2906;2907 6 2906 VValidationDate). 1 Product description This is a two component finishing filler. It is a smooth multi purpose product. It has good sanding properties, strong

More information