Number: 075K0013. Machined surfaces of incoming components must be masked before coating, unless otherwise directed by Engineering.

Size: px
Start display at page:

Download "Number: 075K0013. Machined surfaces of incoming components must be masked before coating, unless otherwise directed by Engineering."

Transcription

1 Number: Name: Organic Coating Performance Requirements for DDC, HDEP, MBE, and MTUDD Components and Engines. Source: MATERIALS ENGINEERING, Jeremy Dean Latest Revision Date: 04/01/2007 Previous Revision Date: 5/9/1996 Approved: Sang Soon Koh Approved: Curtis Glowzinski Approved: Chris Ellswood Approved: Rob Rehnlund Approved: Timothy Schafer Approved: Dan Theriault Approved: Joerg Sieverding Approved: Chris Kafura I. Purpose/Scope: This specification addresses the performance and appearance of coatings used for coating incoming engine components and finished engines. It does not address the requirements for applying the paint, EPA concerns, safety and hazard requirements, or the chemical makeup of the paints used. II. Surface Preparation: All engines require washing with a soap that degreases, resists rust and has a residue that is compatible with our paint adhesion requirements. It must be thorough enough to guarantee good adhesion. Parts to be painted that are not on the engine as it is assembled and tested must be clean and free of all oils, dirt, rust and any residue that may also impair adhesion of the paint. Only parts that are delivered pre-masked may by-pass this requirement. The engine is to be masked as directed by engineering. During masking, it is imperative that no dirt, oil or foreign material be introduced to the surfaces that are to be painted. Machined surfaces of incoming components must be masked before coating, unless otherwise directed by Engineering. III. Requirements: The following determines the performance and appearance of the coatings. Different coating categories have different requirements for tests and the values determined by those tests are detailed in the Table 1. Coatings and coated parts must not exhibit visible in-homogeneities including, but not limited to, runs, drips, sags, spots, changes in gloss or pigmentation, etc. Note: Coatings used for evaluation can be submitted by the coating manufacturer, or prepared in-plant under production conditions. Pre-coated parts will be evaluated individually where possible. When coated panels are used for tests, match as many variables as possible be to the end-use process. Variations in coating thickness greater than mm (0.7 mil) on panels will not be tested. 1 of 6

2 Salt Spray: All coatings must be tested against a salt spray as described in ASTM B117 for the proper time period (see Table 1). The coating to be tested must have an X scribed through it to the base material. Evaluate per ASTM D1654. Humidity: All coatings must be tested against humidity as described by ASTM D2247 for the proper time period (table 1). Evaluate per ASTM D1654. Tape adhesion testing (see below) shall be performed after a 10 minute recovery period. Fuel-Oil Resistance: All coatings must be submerged in No. 2 diesel fuel for 24 hours at 25 C (72 F) and exhibit no permanent changes (blistering, bubbling, etc.). Adhesion: Adhesion is to be tested according to ASTM D3359, Method B. Adhesion requirements are listed in the Table 1. Temperature Resistance: All coatings are to be held at 93 C (200 F) for 2 hours and must exhibit no permanent changes (blistering, bubbling, etc.). The coating must resist imprinting by a thumbnail while at this temperature. Freeze/ Thaw Resistance: All coatings must be able to withstand being held at -7 C (20 F) for 24 hours to the humidity chamber as described in ASTM D2247 for 24 hours without permanent changes (blistering, bubbling, etc.). Color Match: Pigmented coatings must match the color chips (or CIE tristimulus values) supplied by DDC with a CIELAB E of less than 1 under the following three standard illuminants (See ASTM E308): Daylight (D65 or D75), Afternoon/Sunset (A) and Cool White Fluorescent (F2, F7 or F11). The CIELAB E is described in ASTM D3134 and its referenced standards. If there is a difference noticeable to the naked eye, the CIELAB E is greater than 1. It is considered acceptable to compare colors with the standards by eye, but in a dispute, the CIELAB E will be measured as the refereeing metric. Gloss: Coatings with a gloss requirement are to meet those described in the table as tested at 60 by the test described in ASTM D523. (The unit for specular gloss is also called degrees, not to be confused with the degrees of an angle.) Hiding Power: Pigmented coatings must obscure the substrate completely at the minimum thickness described in the table. Marks on the substrate that are visible to the naked eye are not obscured. The after-market touch-up paint requirement is designed to force the applicator to achieve a minimum thickness so that corrosion protection is achieved. Full hiding for this paint must not occur before 2 mils of touch-up paint are applied. *Note: In-house touch-up paint will follow the requirements for and be treated as top coat paint. Thickness: Thickness requirements are listed in Table 1. Measurements are taken using a nondestructive device used in accordance with the manufacturer s operating instructions and properly calibrated. Metallographic preparation of a representative cross-section for measurement in a calibrated microscope is also acceptable. Dry Times: Required minimum dry times are listed in Table 1. This specification considers a coating dry when it is ready to accept a new coat (either a second coat or a different paint that is compatible with the dried paint). Cure Times: Required minimum cure times are listed in Table 1. Cured coatings are to be tested by the ASTM D5402 method using the appropriate solvent (listed in Table 1). Five wipes with a lint-free wipe should not change the gloss on the surface of the paint more than 20 degrees (units of gloss) from the original gloss when measured at a 60 angle. A second, empirical measure of cure is the amount of coatings removed by the cloth. Fully cured coatings will not leave any paint on the wiping cloth. 2 of 6

3 Documentation: Documentation of the following is required for PPAP approval of painted parts: Salt spray tests, Fuel-Oil Resistance, Adhesion, Thickness, Cure Time and MSDS of the coating. No lead, chrome, cadmium, zinc or other toxic materials will be accepted. If the painted part fails one of the other tests listed in the table, the part can be rejected at any time and re-accepted pending the documentation for all the tests. Once a paint system is approved, no aspect may be altered without re-approval. Paints to be applied in-house must have a symbol number (see DDC 90K218) with approvals by Environmental Engineering, Materials Engineering and Purchasing departments. Paints to be applied in-house must meet any and all applicable K-specifications pertinent to the area they will be applied in. Compatibility: All coatings are required to be compatible, and perform adequately with the current coatings that will be applied to them, or they will be applied over. When two coatings are found incompatible, DDC personnel will determine which coating remains accepted. All coatings are required to be compatible and perform adequately with the material that becomes the substrate onto which it is applied. All coatings are required to withstand the cleaners and chemicals that are to be used on the painted surfaces. When cleaners and chemicals are used for this purpose, the compounds will be supplied for tests upon request. Coatings on parts that receive subsequent machining must behave acceptably in those machining operations (coolant compatible, no chipping, peeling, discoloration, softening, etc.). No paint chip generated during machining may be larger than twice the largest dimension of the metal chips generated during machining. Chipping on the edges of machined parts may not extend below 0.25 mm (10 mil) from the machined edge. Coatings will not show any detrimental signs of change when subjected to casting impregnation per DDC spec 91K15. Coatings supplied for application at DDC will be compatible with the equipment and processes used to apply and handle them. The paints shall remain stable with normal handling during their residence in the system used for handling the paints. 3 of 6

4 Classes of Coatings: The classes of finishes are as follows: A168 Water based coatings typically used to coat fully assembled off-highway engines (and ship loose components). A336 Premium coatings typically used to coat fully assembled marine engines (and ship loose components). C168 Water based coating normally used to coat fully assembled on-highway engines. P101 Normally used for incoming as-cast engine components (non-ecoat). P102 Normally used for incoming smooth parts, tubes, brackets, etc. (non-ecoat). P103 Normally used for incoming components requiring cathodic e-coat. T104 After Market touch-up paints normally used on fully assembled engines. 4 of 6

5 TEST DESCRIPTION Salt Spray ASTM B117 Humidity ASTM D2247 Fuel Oil Resistance Adhesion ASTM D3359 Temperature Resistance Freeze/Thaw Resistance Color Match ASTM D3134 Gloss ASTM D523 Hiding Power A168 A336 C168 P101 P102 P103 T hrs Note 1,5 336 hrs Note 1, 3, 4 Note 1, 2,4 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 3B 4B/5B 3B/4B 3B 4B 3B/4B 3B/4B Note 6 Note 6 Note 6 Note 7 Note 7 Note 6 Note 6 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 ΔE <1 ΔE <1 ΔE <1 ΔE <1 ΔE <1 ΔE <1 ΔE <1 > 75 > 90 >75 Note 8 >75 >75 >75 mm (0.8 (0.5 mil) >0.05 mm (>2.0 mil) Thickness mm mm mm (1-4 mil) mm Before packing mm (1.5-4 mil) mm ( mil) N/A mm 45 min Dry Time 45 min Note 9 45 min C Before packing Cure Time 7 days 7days 7 days Before Before Before 7 days ASTM D5402 Note 10 Note 10 Note 10 Packing packing packing Note 10 Note 10 Note 10 Note 10 *The values listed in this table may be superseded by blueprint requirements when specified.* Notes: 1. No evidence of blistering, bubbling, peeling, softening, discolorization or other permanent changes. 2. Maximum allowable creep back is 3 mm. 3. Maximum allowable creep back is 1 mm. 4. No more than 10% of the surface (exclusive of scribes and exceeding 3 mm of sharp edges). 5. No change in adhesion per ASTM D3359 is permissible. 6. The first number refers to adhesion to an as-cast surface; the second number refers to a machined surface. 7. Adhesion measurements are to be taken on the predominant surface. 8. Gloss of clear coat must be > Primer must be able to accept top coat in 15 minutes. 10. An appropriate solvent must be used for the type of coating used. Please contact your paint vendor for suggested solvent. 5 of 6

6 Record of Change 11/96 Title Changed from Paint Requirements for Series 60 Engine and Components to Pre-Coating of Engine Components and finish Coating After Assembly Necessary changes to accommodate alternative product and coating processes were carried out. 07/98 Revised powder coat application (E-2) Revised characteristics of base coat (G-2, 3 & 7) Revised paint thickness criteria in test panel preparation. (H1) Revised test parameters (H2-3) Revised characteristics of clear coat. (I-1, 2) 07/99 Revised paint thickness criteria in base coat preparation. (F2) Added addition characteristic of base coat. (F3) Revised salt spray (corrosion) (H-2, 3). Revised characteristics of base coat (F-1, 4) Revised Base Coat Designations (E-2) 3/02 Re-written for clarity. Revised to include applicable specifications. Expanded to include Marine applications, e-coat and specific characteristics that have become apparent since the last revision. Title changed to Organic Coatings for Engine Parts and Engines. 4/07 Re-written for clarity. Expanded to include HDEP and MBE 900 applications. Title changed to Organic Coating Performance Requirements for DDC, HDEP, MBE, and MTUDD Components and Engines 6 of 6

COMMERCIAL ITEM DESCRIPTION ELECTROCOATING PRIMER

COMMERCIAL ITEM DESCRIPTION ELECTROCOATING PRIMER [INCH-POUND] March 1, 2010 SUPERSEDING A-A-52474A December 4, 1996 COMMERCIAL ITEM DESCRIPTION ELECTROCOATING PRIMER The General Services Administration has authorized the use of this commercial item description

More information

STANDARD NO.: Z0254. ECO 13848: Added revision table and standard format. Minor corrections made through out the document.

STANDARD NO.: Z0254. ECO 13848: Added revision table and standard format. Minor corrections made through out the document. PAGE 1 OF 7 APPROVAL FOR RELEASE FOR USE: POSITION: NAME: DATE: POSITION: NAME: Paint Line Mfg Eng J. Pidima 4/9/2012 Mfg Eng Mgr R.Luety 4/9/2012 Quality Mgr J Meyers 4/9/2012 CHANGE CONTROL: REV: DATE:

More information

Refer to Substrates & Surface Preparation.

Refer to Substrates & Surface Preparation. SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance

More information

Protective Industrial Polymers - USA Manufacturer s Specification February 11, 2015

Protective Industrial Polymers - USA Manufacturer s Specification February 11, 2015 This specification covers InhibiChem SR-GF-L Enhanced Chemical and Solvent-Resistant Glass-Flake Reinforced Steel Tank Lining System. This system consists of a vinyl ester primer, and two troweled coats

More information

1.04 REFERENCES STANDARDS.1 For reference standards tests & results refer to Manufactures Product Data Sheets

1.04 REFERENCES STANDARDS.1 For reference standards tests & results refer to Manufactures Product Data Sheets This specification covers InhibiChem CR-GF-L Chemical-Resistant Glass Flake-Reinforced Steel Tank Lining System. This system consists of a vinyl ester primer, and two troweled coats of glass flake filled

More information

Refer to Substrates & Surface Preparation.

Refer to Substrates & Surface Preparation. SELECTION & SPECIFICATION DATA Generic Type Description Features Aliphatic Acrylic Polyurethane High gloss finish with exceptional weathering performance characteristics. Used extensively in virtually

More information

One component, heat-resistant, universal silicone topcoat for use in elevated temperature systems. Replaces HI-TEMP 1000 V / VS / VHA

One component, heat-resistant, universal silicone topcoat for use in elevated temperature systems. Replaces HI-TEMP 1000 V / VS / VHA DESCRIPTION One component, heat-resistant, universal silicone topcoat for use in elevated temperature systems. Replaces HI-TEMP 1000 V / VS / VHA PRINCIPAL CHARACTERISTICS Heat-resistant topcoat with highly

More information

Measured in accordance with ASTM D 2697.

Measured in accordance with ASTM D 2697. SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Service Temperature Solvent Based Inorganic Zinc Ultra-low VOC member of the Carbozinc family with extraordinary corrosion

More information

Elastocoat Protective Coatings APPLICATION GUIDE

Elastocoat Protective Coatings APPLICATION GUIDE Elastocoat Protective Coatings DESCRIPTION Elastocoat polyurea and polyurethane coatings are two-component, 100% solids elastomer systems. The coatings systems are designed for processing through plural

More information

SECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015

SECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 Specification Provided To: Date: Job: PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 96 60 HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 A. Paints and coatings of the following

More information

Carboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy

Carboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial

More information

SECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.

SECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate. Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call

More information

The City of Winnipeg NEWPCC Lab Renovation

The City of Winnipeg NEWPCC Lab Renovation Bid Opportunity 253-2011 Page 1 of 6 Part 1 General 1.1 SUMMARY.1 Work under this contract includes, but is not necessarily limited to:.1 Surface preparation of substrates as required for acceptance of

More information

Venger Electrostatic Coatings Master Specification Page 1

Venger Electrostatic Coatings Master Specification Page 1 Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits

More information

Measured in accordance with ASTM D 2697.

Measured in accordance with ASTM D 2697. SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Service Temperature Solvent Based Inorganic Zinc Ultra-low VOC member of the Carbozinc family with extraordinary corrosion

More information

ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019

ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019 ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # 275-18 ADDENDUM NO. 3 April 02, 2019 This Addendum No. 3 ( Addendum ) is dated the date set forth above and modifies certain Bidding Documents issued

More information

BR 252 Water Based Bonding Primer

BR 252 Water Based Bonding Primer TECHNICAL DATA SHEET AEROSPACE MATERIALS BR 252 Water Based Bonding Primer DESCRIPTION BR 252 corrosion inhibiting primer is a non chromated, one part, modified epoxy bonding primer. It is designed to

More information

Aliphatic Acrylic-Polyester Polyurethane

Aliphatic Acrylic-Polyester Polyurethane SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance

More information

All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A366.

All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A366. 1 STEEL All hollow metal doors and frames manufactured in North America are produced from the identical base cold rolled steel, which conforms to ASTM A. The galvanneal process begins in the Hot Strip

More information

Application Guide for Jotun Durasol Powder Coatings

Application Guide for Jotun Durasol Powder Coatings for Jotun Durasol Application Guide for Jotun Durasol Powder Coatings Date of Last Revision: October 2017 Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview 3 3.0 Scope.3 4.0 Safety Considerations..3

More information

CORAFLON POWDER COATINGS

CORAFLON POWDER COATINGS CORAFLON POWDER COATINGS PRODUCT DATA PRODUCT DESCRIPTION CORAFLON spray-applied architectural extrusion powder coatings are thermosetting fluoropolymer systems which are recommended for use in a variety

More information

Salt Spray Resistance

Salt Spray Resistance Salt Spray Resistance Test No. TP02 This test procedure is used to determine the resistance of the paint/polymer system used for the Texture Plus system in resisting degradation when subject to salt spray.

More information

SPECIAL SPECIFICATION 5478 Anti-Graffiti Coating

SPECIAL SPECIFICATION 5478 Anti-Graffiti Coating 1995 Metric CSJ 0981-01-086 SPECIAL SPECIFICATION 5478 Anti-Graffiti Coating 1. Description. This Item shall govern for furnishing, surface preparation and application of materials used to deter the adhesion

More information

SPECIAL SPECIFICATION 5457 Anti-Graffiti Coatings

SPECIAL SPECIFICATION 5457 Anti-Graffiti Coatings 1995 Metric CSJ 1316-01-028 SPECIAL SPECIFICATION 5457 Anti-Graffiti Coatings 1. Description. This Item shall govern for furnishing, surface preparation and application of materials used to deter the adhesion

More information

Coating Performance Not as Simple as it would Appear

Coating Performance Not as Simple as it would Appear TECHNICAL BULLETIN Coating Performance Not as Simple as it would Appear Overview When ordering a (finish) for the building panels, you would think that the biggest choice would be color. Not true. There

More information

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Typical applications. Features. Finish and Color. TIGER Shield

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Typical applications. Features. Finish and Color. TIGER Shield Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Epoxy zinc-rich powder coating primer. Part of a two-coat TIGER Shield system. Designed to impart superior corrosion protection to steel

More information

Acrylitex Interior Texture and Coating Submittal Documentation

Acrylitex Interior Texture and Coating Submittal Documentation Acrylitex Interior Texture and Coating Submittal Documentation Project: Contractor: Installer: Supplier: John Wagner & Associates dba Grabber Construction Products 866-237-GRAB(4722) Distributor: Acrylic

More information

SPECIAL SPECIFICATION 5764 Anti-Graffiti Coatings

SPECIAL SPECIFICATION 5764 Anti-Graffiti Coatings 1993 Specifications SPECIAL SPECIFICATION 5764 Anti-Graffiti Coatings 1. Description. This Item shall govern for furnishing, surface preparation and application of materials used to deter the adhesion

More information

WHAT IS INDUSTRIAL PAINT?

WHAT IS INDUSTRIAL PAINT? WHAT IS INDUSTRIAL PAINT? BASIC CONCEPTS (see also Paint Systems) Preparation is very important to get a good result. A badly prepared surface painted with a high quality paint has normally worse results

More information

Application Guide for Jotun Super Durable 2901, 2903, 2905 and 2908 Powder Coatings

Application Guide for Jotun Super Durable 2901, 2903, 2905 and 2908 Powder Coatings for Jotun Super Durable 2901, 2903, 2905 and 2908 Application Guide for Jotun Super Durable 2901, 2903, 2905 and 2908 Powder Coatings Date of Last Revision: March 2018 Page 1 of 7 for Jotun Super Durable

More information

SECTION 1045 PAINT FOR STRUCTURAL STEEL

SECTION 1045 PAINT FOR STRUCTURAL STEEL SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Paint and Paint Material. 1045.1.1 General. All single component paints shall be ready-mixed at the factory to comply with the specification formula for the

More information

Intercure 99NA Application Guidelines

Intercure 99NA Application Guidelines International Paint Ltd Protective Coatings Technical Operations Intercure 99NA Application Guidelines Prepared by: PC Technical Support International Paint Ltd. www.international-pc.com The information

More information

F.S.P.M.A. CUSTODIAL/FOOD SERVICE CHEMICAL SPECIFICATION FOR GENERAL EDUCATION FACILITIES USE

F.S.P.M.A. CUSTODIAL/FOOD SERVICE CHEMICAL SPECIFICATION FOR GENERAL EDUCATION FACILITIES USE F.S.P.M.A. CUSTODIAL/FOOD SERVICE CHEMICAL SPECIFICATION FOR GENERAL EDUCATION FACILITIES USE SPEC. NO. PBCC-33.0 TWO COMPONENT, ALIPHATIC POLYURETHANE, WATERBORNE, ZERO VOC, ODORLESS PIGMENTED PERMANENT

More information

Application Guide for Jotun Super Durable 2003 and 2008 Powder Coatings

Application Guide for Jotun Super Durable 2003 and 2008 Powder Coatings for Jotun Super Durable 2003 and 2008 Application Guide for Jotun Super Durable 2003 and 2008 Powder Coatings Date of Last Revision: April 2018 Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview

More information

Architectural Testing

Architectural Testing Architectural Testing PERFORMANCE TEST REPORT Rendered to: SUMMIT GLASS COATINGS, LLC PRODUCT: Back-Painted Glass Report No: C7713.01-106-31 Report Date: 07/11/13 Test Record Retention Period: 07/11/17

More information

Instructions for On-Site Coating of Vinyl Windows

Instructions for On-Site Coating of Vinyl Windows www.aqua-diy.com Instructions for On-Site Coating of Vinyl Windows Aqua DIY D100 is a high performance heat reflective water-based coating. It has been shipped to you with a thickness suitable for manual

More information

PPG HI-TEMP 1000 VS. PRODUCT DATA SHEET December 10, 2014 (Revision of June 30, 2014) DESCRIPTION

PPG HI-TEMP 1000 VS. PRODUCT DATA SHEET December 10, 2014 (Revision of June 30, 2014) DESCRIPTION DESCRIPTION One-component, heat-resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat-resistant

More information

Hardener: at least 24 months when stored cool and dry

Hardener: at least 24 months when stored cool and dry DESCRIPTION Two-component, engineered siloxane coating PRINCIPAL CHARACTERISTICS Unique, high gloss, engineered siloxane Virtually HAPs free, ultra-low VOC High durability in challenging environments Tough

More information

Maximum Rust Protection!

Maximum Rust Protection! ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric

More information

PPG HI-TEMP 1000 V (AMERCOAT 873) PRODUCT DATA SHEET December 10, 2014 (Revision of June 30, 2014) DESCRIPTION

PPG HI-TEMP 1000 V (AMERCOAT 873) PRODUCT DATA SHEET December 10, 2014 (Revision of June 30, 2014) DESCRIPTION DESCRIPTION One-component, heat-resistant silicone topcoat for use in an elevated temperature coating system PRINCIPAL CHARACTERISTICS Heat-resistant topcoat with highly engineered silicone resin; able

More information

SECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system.

SECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system. PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Fusion welded and rackable ornamental steel picket fence system. B. Related sections: 1. Section 03310 Concrete Work for post support. 2. Section 09960

More information

AAMA Voluntary Specification, Performance Requirements and Test Procedures For Pigmented Organic Coatings on Aluminum Extrusions and Panels

AAMA Voluntary Specification, Performance Requirements and Test Procedures For Pigmented Organic Coatings on Aluminum Extrusions and Panels A M E R I C A N A R C H I T E C T U R A L AAMA 2603-02 Voluntary Specification, Performance Requirements and Test Procedures For Pigmented Organic Coatings on Aluminum Extrusions and Panels M A N U F A

More information

1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.

1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials

More information

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90701) Typical applications. Features. Finish and Colour. TIGER Shield

Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90701) Typical applications. Features. Finish and Colour. TIGER Shield Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90701) Epoxy zinc-rich powder coating primer. Part of a two-coat TIGER Shield system. Designed to impart superior corrosion protection to steel

More information

3 Thermal range of application of the coated parts Continuous operational temperature range: JED to C to +80 C JED C to +120 C

3 Thermal range of application of the coated parts Continuous operational temperature range: JED to C to +80 C JED C to +120 C Specification 2014-05 Class: Coating Materials Class No.:29 Coating material for protection of reservoirs JED 745 Previous Edition Part name (for databases) 2012-06 Paint; Exterior protection of reservoirs

More information

P R O D U C T D A T A S H E E T

P R O D U C T D A T A S H E E T P R O D U C T D A T A S H E E T Description Petroguard Tape UW is composed of a non-woven synthetic fabric carrier, fully impregnated with a neutral compound based on saturated petroleum and inert silicious

More information

VengerElectrostatic Coatings Master Specification Page 1

VengerElectrostatic Coatings Master Specification Page 1 Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits

More information

Application Guide for Jotun Reveal Edge D / W Powder Coatings

Application Guide for Jotun Reveal Edge D / W Powder Coatings for Jotun Reveal Edge D / W Application Guide for Jotun Reveal Edge D / W Powder Coatings Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview 3 3.0 Safety Considerations..3 4.0 Surface preparation

More information

Application Guide for Internal Flow Efficiency Coating

Application Guide for Internal Flow Efficiency Coating Jotapipe FC 407 Application Guide for Internal Flow Efficiency Coating Jotapipe FC 407 Date of Last Revision: March 2015 Page 1 of 6 Contents 1.0 Product Description... 2 2.0 Surface preparation and cleanliness...

More information

Property Test/Standard Description

Property Test/Standard Description Other Technical Data Sheet 24100;24120;26200 1 24100 VValidationDate). 1 Product description This is a two component, anticorrosive water borne epoxy coating. It is a versatile, fast drying product containing

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 392 F (200 C) and can be applied on hot

More information

Carboxane 950 Metallic

Carboxane 950 Metallic SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Fluorourethane Premium, ultra-durable ambient cured finish meeting performance requirements. 950

More information

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 23680;1551 1,2 23680 epoxy mastic ^(ValidationDate) 1 Product description This is a two component amine cured epoxy mastic coating. It is a surface tolerant, high solids product. It is aluminum

More information

Application Guide for Architectural Powder Coatings using Powder on Powder Wood Finish

Application Guide for Architectural Powder Coatings using Powder on Powder Wood Finish Powder on Powder Wood Finish Application Guide for Architectural Powder Coatings using Powder on Powder Wood Finish Date of Last Revision: April 2016 Page 1 of 8 Contents 1.0 Introduction 3 2.0 General

More information

NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM. Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN

NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM. Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN Paper No. 0 20 NEW AIRCRAFT PRETREATMENT & WASH PRIMER SYSTEM Angel Green Cortec Corporation 4119 White Bear Parkway White Bear Lake, MN 551 agreen@cortecvci.com ABSTRACT Today s Department of Defense

More information

THERMOFIT ADHESIVE S Flex Fluid Resistant, High Temperature, One Part-Flexible Epoxy

THERMOFIT ADHESIVE S Flex Fluid Resistant, High Temperature, One Part-Flexible Epoxy TE Connectivity 30 Constitution Drive Menlo Park, CA 9402 USA SPECIFICATION THIS ISSUE: DATE: REPLACES: RT-1014 ISSUE 4 April 19, 2016 Issue 3 1. SCOPE THERMOFIT ADHESIVE S-12-04 Flex Fluid Resistant,

More information

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 2124;7720 1,2 7720 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc epoxy coating. It provides corrosion protection as part of a complete coating

More information

Dist. by: BEST MATERIALS Ph:

Dist. by: BEST MATERIALS Ph: Dist. by: BEST MATERIALS Ph: 800-474-7570 www.bestmaterials.com Email: Sales@BestMaterials.com NOVALINK SL SELF-LEVELING CONSTRUCTION SEALANT DIVISION 7 - THERMAL AND MOISTURE PROTECTION SECTION 07 92

More information

1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)

1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F) DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (32 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (32 C) calculated VOC-US/Hong Kong Approved 2920;2401 1 2920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

SULPHURIC ACID ANODIZING KJ ATTACHMENT NO. 2 TO KJ-06

SULPHURIC ACID ANODIZING KJ ATTACHMENT NO. 2 TO KJ-06 KJ 06.02 ATTACHMENT NO. 2 TO KJ-06 KJ-06.02 translated by: Justyna Kilian; Date: 02/22/2017 Compiled by: Małgorzata Groele Dział Techniczny DTT-8 Approved by: Dariusz Nykiel Process Engineering Office

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 2401;3440 1 3440 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product.

More information

DEBOURCH MFC. CO. JWB COUNSUL TINC SERVICES

DEBOURCH MFC. CO. JWB COUNSUL TINC SERVICES TECHNICAL REPORT PROJECT NUMBER 21901.01 DEBOURCH MFC. CO. JWB COUNSUL TINC SERVICES SALT SPRAY TESTING PER ASTM B---117 Fourth stage: Fifth stage: Fresh Water ambient rinse with 30-45 second dwell times.

More information

Downloaded from MIL-DTL-19834C w/ AMENDMENT 1 9 February 2011 SUPERSEDING MIL-DTL-19834C 6 July 2006 DETAIL SPECIFICATION

Downloaded from  MIL-DTL-19834C w/ AMENDMENT 1 9 February 2011 SUPERSEDING MIL-DTL-19834C 6 July 2006 DETAIL SPECIFICATION INCH-POUND 9 February 011 SUPERSEDING July 00 DETAIL SPECIFICATION PLATES, IDENTIFICATION OR INSTRUCTION, METAL FOIL, ADHESIVE BACKED GENERAL SPECIFICATION FOR This specification is approved for use by

More information

NAVSEA REVIEWED ASTM F-718. Tenacious One Step Epoxy Flooring

NAVSEA REVIEWED ASTM F-718. Tenacious One Step Epoxy Flooring ASTM F-718 International Diverse Flooring Tenacious One Step Epoxy Flooring MIL-PRF-24613 If this product is to be applied as part of a coating system, all components of the system must be as listed on

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 23660 1,2 23660 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is an aluminum pigmented product. It is heat resistant

More information

TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR

TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR DESCRIPTION: A two component water base epoxy amine coating that provides excellent adhesion, solvent resistance and abrasion resistance with

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong Approved 20940;16620 1 20940 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high

More information

PPG Guide Specification

PPG Guide Specification PPG Guide Specification Coil and Extrusion Coatings, Liquid and Powder Coating Systems SECTION 050513 - SHOP-APPLIED COATINGS FOR METAL SECTION 05080 - FACTORY-APPLIED METAL COATINGS Revised October 2,

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C VOC-USA / VOC Hong Kong EPA Method 24

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C VOC-USA / VOC Hong Kong EPA Method 24 Other Technical Data Sheet 2920;2401 1 2920 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids,

More information

COMMERCIAL ITEM DESCRIPTION CORROSION PREVENTIVE COMPOUNDS, COLD APPLICATION (FOR NEW AND FIELDED MOTOR VEHICLES AND TRAILERS)

COMMERCIAL ITEM DESCRIPTION CORROSION PREVENTIVE COMPOUNDS, COLD APPLICATION (FOR NEW AND FIELDED MOTOR VEHICLES AND TRAILERS) [METRIC] 9 September 1998 SUPERSEDING MIL-PRF-62218B 3 June 1996 COMMERCIAL ITEM DESCRIPTION CORROSION PREVENTIVE COMPOUNDS, COLD APPLICATION (FOR NEW AND FIELDED MOTOR VEHICLES AND TRAILERS) The General

More information

COATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006

COATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006 COATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006 Amendment to OPSS 911, November 2004 for hot dip galvanizing and subsequent painting, where required,

More information

HAMMERITE NO. 1 RUST BEATER PRIMER

HAMMERITE NO. 1 RUST BEATER PRIMER TECHNICAL DATA SHEET Version 2 2018 June THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Hammerite No.1 Rust Beater provides a high build finish to heavily pitted areas of rust and

More information

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

Property Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong) Approved 2401;3440 1,2 3440 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high

More information

SECTION INTUMESCENT FIREPROOFING

SECTION INTUMESCENT FIREPROOFING SECTION 078123 INTUMESCENT FIREPROOFING PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. 1.2

More information

Refer to Substrates & Surface Preparation.

Refer to Substrates & Surface Preparation. SELECTION & SPECIFICATION DATA Generic Type Description Features Colour Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance characteristics. Used extensively

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (33 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (33 C) calculated VOC-US/Hong Kong Approved 24760;24700 1 24760 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. This product is LEED compliant and contains no solvents on the Hazardous Air

More information

two component polyamide cured epoxy primer yellow/green - eggshell

two component polyamide cured epoxy primer yellow/green - eggshell 6 pages Revision of December 006 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 0 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

A M E R I C A N A R C H I T E C T U R A L AAMA

A M E R I C A N A R C H I T E C T U R A L AAMA A M E R I C A N A R C H I T E C T U R A L AAMA 2603-15 Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels (with Coil

More information

TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115)

TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115) TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115) DESCRIPTION: A two component water base epoxy amine coating that provides excellent adhesion, solvent resistance and abrasion resistance with water

More information

Fireside 258. Fireside 258 is very stable and will neither outgas, nor cause skin irritations like many other high temperature coatings.

Fireside 258. Fireside 258 is very stable and will neither outgas, nor cause skin irritations like many other high temperature coatings. ` Fireside 258 PRODUCT DISCRIPTION: Fireside 258 is a double component ceramic coating specifically formulated to promote thermal efficiency while preventing high temperature corrosion and erosion of carbon

More information

Product Data Sheet. Suitable for electrostatic spray Specific gravity g/cm³ Storage

Product Data Sheet. Suitable for electrostatic spray Specific gravity g/cm³ Storage Product Data Sheet AL113D Product Description Interpon BPP 330 is a barrier protective powder primer that is designed to give enhanced corrosion protection of mild steel and hot dip galvanized steel. Interpon

More information

One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer

One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat

More information

SIGMAZINC 158. PRODUCT DATA SHEET January 7, 2015 (Revision of December 15, 2014) DESCRIPTION

SIGMAZINC 158. PRODUCT DATA SHEET January 7, 2015 (Revision of December 15, 2014) DESCRIPTION DESCRIPTION Two-component, moisture-curing zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS Certificate for ASTM A-490 class 'B' for slip coefficient Complies with the compositional requirements

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C Other Technical Data Sheet 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 200 C and can

More information

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong

Approved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.

More information

COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING

COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING [INCH-POUND] A-A-59485 24 February 2000 SUPERSEDING MIL-P-38477A 30 August 1973 COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING The General

More information

COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING

COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING [INCH-POUND] 24 February 2000 SUPERSEDING MIL-P-38477A 30 August 1973 COMMERCIAL ITEM DESCRIPTION PLASTIC MATERIAL, PRESSURE SENSITIVE ADHESIVE, FOR AEROSPACE IDENTIFICATION AND MARKING The General Services

More information

MnDOT Traffic Signal Pole Duplex Paint Qualification Procedure

MnDOT Traffic Signal Pole Duplex Paint Qualification Procedure MnDOT Traffic Signal Pole Duplex Paint Qualification Procedure 1. Send a personalized submittal package to: Allen Gallistel Chemical Lab Director MnDOT Office of Materials and Road Research 1400 Gervais

More information

Installation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage

Installation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage Important Storage Flat sheet - Store Palladium Rigid Sheet in a clean, dry, interior area at temperatures between 50 F and 95 F [10-35 C]. Keep out of direct sunlight. Make sure sheet is well supported.

More information

Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer

Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer Ganicin 2.8 ZR- U Zinc-Rich Polyurethane Primer GENERAL DESCRIPTION A three-package, VOC conforming (2.8 lbs/gal) low HAPS, zinc-rich urethane primer based on Axalta polyurethane technology. The resulting

More information

SURFACE INSPECTION ACCEPTANCE CRITERIA

SURFACE INSPECTION ACCEPTANCE CRITERIA OC #: QAP 3.0-3 PAGE: 1 OF 6 REVISION RECOR EFFECTIVE REVISE BY APPROVE BY REVISION 10-02-2012 R. Montfort P. Robino Revision N/C 10-23-2012 R. Montfort P. Robino Revision A Revised to clarify visual criteria

More information

APPLICATION GUIDELINE FOR

APPLICATION GUIDELINE FOR APPLICATION GUIDELINE FOR Company Name M/V SEA-SPEED V 10 X (100 % solids) (Hard film siloxane hybrid foul release coating) SCOPE This specification, together with the Product Data Sheet, defines the minimum

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 35 C

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 35 C Other Technical Data Sheet 13640;13641 1 13640 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is an ultra high build, high solids abrasion resistant

More information

SECTION ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY

SECTION ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY 3-PART SPEC ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY SECTION 05720 A. Section Includes: a. Solutions aluminum extruded shape top rail, square or round balustrade & rectangular bottom

More information

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell

two component polyamide cured epoxy primer yellow/green (redbrown on request) - eggshell 5 pages Revision of September 2009 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading

More information

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1

Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 7461;7680 1 7680 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It conforms

More information

AAMA Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and

AAMA Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and A M E R I C A N A R C H I T E C T U R A L AAMA 2604-05 Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and Panels M A

More information

COATING SPECIFICATION INORGANIC ZINC SILICATE, EPOXY PRIMER MIST-COAT, TWO PACK ACRYLIC TOP COAT ON STEEL OR CAST IRON

COATING SPECIFICATION INORGANIC ZINC SILICATE, EPOXY PRIMER MIST-COAT, TWO PACK ACRYLIC TOP COAT ON STEEL OR CAST IRON 1.0 SCOPE This document summarises the procedure for the application of Inorganic Zinc Silicate (IZS), Epoxy Primer Mist Coat coat followed by two pack Acrylic on Steel or Cast Iron structures. Refer Design

More information

Pacific Polymers Elasto-Deck 5000X2 Guide Specification

Pacific Polymers Elasto-Deck 5000X2 Guide Specification 1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide

More information