ROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART GENERAL 1.
|
|
- Kristopher Gervase Edwards
- 6 years ago
- Views:
Transcription
1 ROOF BALLAST MATERIALS ARCHITECTURAL CONCRETE PAVING SLABS SRS LEVELING BLOCK SYSTEM INSTALLATION PART GENERAL 1.01 SUMMARY: A. The work of this section consists of furnishing and installing architectural concrete paving slabs with the SRS Leveling System over a metal deck and/or structural concrete deck for exterior applications. Drawings and other general provisions of the contract documents, including General Conditions, apply to work of this section. B. Other related sections that may affect work in this section may include: Deck Drains Landscape Accessories Concrete Materials Masonry Cleaning and Restoration Expansion Control Waterproofing Roof and Deck Insulation Sheet Metal Flashing and Trim Roof Accessories Sealants and Caulking 1.02 REFERENCES: A. American Society for Testing and Materials (ASTM) 1. ASTM C-33: Specification for Concrete Aggregates 2. ASTM C-150: Specification for Portland Cement 3. ASTM C-140: Specification for Concrete 4. ASTM C-578: Specification for Polystyrene foam materials 5. ASTM C-203: Specification for Polystyrene Flexural Strength 6. ASTM C-272: Specification for Polystyrene minimum moisture absorption 7. ASTM D-1621: Specification for Polystyrene compressive strength testing 1.03 SYSTEM DESCRIPTION: A. Pavement shall consist of architectural concrete paving slabs installed with the patented SRS Leveling System over a Type VII 60 psi (or 100 psi) polystyrene protection/insulation board or asphalt impregnated protection board with drainage mat. This system shall be installed over an approved waterproofing system or as part of a complete single-source warranted waterproofing package as specified by waterproofing manufacturer.
2 B. Architectural concrete paving slabs and the SRS Leveling System shall only be installed by a fully trained and licensed SRS system applicator, or by an approved contractor working jointly with the SRS Licensor under a single project agreement SUBMITTALS: A. Submit the following in accordance with General Conditions: 1. Manufacturer's Literature: a. Architectural paving slab product literature, installation instructions and color selection charts. b. SRS Leveling System technical brochure and/or installation instructions. c. 60 psi (or 100 psi) polystyrene foam product literature and technical data. d. Adhesive product literature and technical data. 2. Samples: a. Submit two sample blocks representing each color and texture of the paving slabs required for the project, showing the extreme variations in quality, color, texture and edge chamfers. b. Submit two SRS Polystyrene leveling blocks (8", 9 5/8", or 12" square). c. Submit two 1/8" or 3/16" neoprene rubber SRS Spacing Tabs QUALITY ASSURANCE: A. Installer Qualifications: Contractor or subcontractor shall be a licensed SRS Leveling System Installation Contractor in good standing who has successfully completed the SRS Training Program, or shall work jointly with the SRS licensor with a single project agreement. 1. Experience in installing paving slabs using a comparable pedestal system, having successfully completed during the last five years an average of one or more projects per year of similar size and scope. 2. Supervisory personnel with experience on these similar projects will be made available for this project. 3. If requested, the installation contractor or subcontractor shall submit a list of comparable projects describing project size, location, and contractor/owner references with addresses and telephone numbers.
3 1.06 PRODUCT DELIVERY, STORAGE AND HANDLING: A. Protect paving slabs and accessory materials during shipment, Storage and construction against moisture, soiling, staining and Physical damage. B. Handle paving slabs to prevent chipping, breakage, soiling or other damage. C. Protect adhesive materials from moisture and temperature. Store in a dry location PROJECT CONDITIONS: A. Comply with manufacturer's requirements regarding weather, substrate and other project conditions. Do not install the paving slabs or adhesives during freezing weather, or on a frozen surface. B. Protect all stored materials and installed work from possible damage by other trades SEQUENCING AND SCHEDULING: A. Coordinate the sequencing, scheduling, and installation of the SRS Leveling System and the paving slabs with other related or adjacent work to ensure that the work is completed in a timely manner MANUFACTURERS: A. The SRS Leveling System is manufactured and installed by: Syrstone, Inc. Syrstone, Inc Taft Park Drive 761 Biggs Highway East Syracuse, NY Rising Sun, MD Telephone: Telephone: FAX: Fax: WARRANTY: A. Standard materials warranty for architectural paving slabs and the SRS Leveling System is one year. B. Standard installation warranty for the complete system is one year. C. Extended warranties are available through single-source waterproofing system warranties. PART PRODUCTS 2.01 GENERAL A. The plaza deck pavement shall be constructed using architectural paving slabs from an acceptable manufacturer and the patented SRS Leveling System.
4 2.02 MATERIALS A. SRS Leveling System: 1. The elevated, open draining paving slab system shall be installed using the patented SRS Leveling System. a. The SRS leveling blocks shall be 60 psi or 100 psi extruded polystyrene foam material. b. Typical SRS leveling blocks shall be 8"x8", 9 5/8" x 9 5/8", or 12"x12". Pedestals 12" or higher shall be 12"x12". Other project-specific pedestal sizes and shapes may be recommended. c. The SRS Leveling System shall use 1/8" or 3/16" neoprene rubber SRS spacing tabs. 2. SRS Leveling System Reference Standards: a. SRS leveling blocks shall conform to the following ASTM standards: ASTM C-78: Specification for polystyrene foam materials ASTM C-203: Specification for polystyrene flexural strength ASTM C-272: Specification for polystyrene minimum moisture absorption ASTM D-1621: Specification for polystyrene compressive strength testing 3. SRS Leveling System Performance Standards: a. SRS leveling blocks shall be 60 psi or 100 psi polystyrene foam. b. SRS leveling blocks shall have a maximum water absorption rate of.3%. d. SRS leveling blocks shall have a flexural strength of 75 psi. B. Polystyrene Adhesive: 1. SRS leveling system adhesive shall be (Chemrex/Ohio Sealant) PL300, QB300, PL Premium or approved equal as necessitated by compatibility requirements with the immediately underlying substrate. C. Waterproofing System Preparation: 1. Prior to waterproofing, the structural concrete slab and insulation layers must be designed to accommodate anticipated pedestrian loads. 2. All waterproofing, flashing, caulking, insulation, drainage mats and protection board materials, as well as the waterproofing of all deck penetrations, shall be determined and installed in accordance with waterproofing manufacturer's recommendations.
5 PART EXECUTION 3.01 INSPECTION: A. Examine all surfaces to receive the work specified herein. Verify all dimensions of existing and subsequent construction and compare layout of deck to shop drawings and architect's drawings. All variances of field conditions from drawings shall be reviewed and corrected prior to the installation of the paving slabs. Notify the Contractor in writing of any conditions detrimental to the proper and timely completion of the work. Do not proceed with the work until unsatisfactory conditions have been corrected PREPARATION: A. Barricade or otherwise isolate work area during paving slab installation and sealing. Keep barricades in place until the entire pavement is fully installed and complete. B. Lay out pattern in straight courses, symmetrical about centerlines and correctly terminated at all edges. Maintain alignment and patterns as shown on plans and details INSTALLATION: A. Preparation: 1. Prior to placing the SRS Leveling System and the concrete paving slabs, remove all foreign materials from the deck. Sweep the protection/insulation layer with a broom to ensure deck is clean. 2. Ensure that all waterproofing, insulation and protection layers are secure and are laying flat with no pumping or movement of the layers from pedestrian traffic. B. General: 1. Paving slabs shall be free from stain, dirt, or dust. 2. Install paving slabs with skilled mechanics and employ skilled fitters at the site for necessary field cutting as units are set. C. SRS Leveling System: 1. Using a laser leveling system, establish and mark the finished elevation of the plaza deck. 2. Establish and mark the top elevation of the SRS leveling blocks by subtracting the nominal thickness of the overlying concrete pavings slabs from the finished elevation of the plaza deck. 3. Identify and transfer the layout of the paving slabs to the top layer of the protection / insulation board. 4. Center and adhere the SRS leveling blocks at the intersections of the X and Y axis. 5. Level the SRS blocks using the patented SRS Leveling System, as per licensor's recommended procedures / installation manual.
6 6. Transfer paving slab layout to the tops of the leveled SRS blocks. 7. Install SRS spacing tabs at the intersections of the X and Y axis. 8. Place SRS leveling blocks tight against parapets and structural walls. Field cut SRS leveling blocks at the appropriate angle, if required, to accommodate any deck elevation variation at the deck perimeter or at structural walls. 9. Install and level primary and secondary SRS leveling blocks with traversing piece where SRS leveling block locations occur over deck drains, as per licensor's recommended procedures / installation manual. 10. Adjust paving slabs and SRS leveling blocks as per licensor's recommended procedures / installation manual to maintain slab-to-slab tolerance of 1/16" or less. 11. Adjust paving slabs as required to maintain 1/8" or 3/16" +/- 1/16" straight joints CLEANING: A. Remove and replace paving slabs which are chipped, broken, stained or otherwise damaged, and re-set units that rock or do not match adjoining units as specified. Provide new units to match adjoining units and install in the same manner as original units with the same joint spacing to eliminate evidence of replacement. B. After completion of the work, clean exposed surfaces as necessary. If a cleaning solution is used, verify with solution manufacturer that product is compatible with the paver, polystyrene foam, protection board, and waterproofing. Pressure washers, when using higherpressure nozzles, may leave indelible marks on concrete pavers PROTECTION: A. After installation and cleaning, protect work from damage during subsequent construction activities until work is completed. B. At completion of construction work, remove all temporary protection from the site. C. Clean up and remove all debris and equipment. END OF SECTION
PAVING SLABS ON AGGREGATE BED FOR ROOF PLAZA DECKS
SECTION 32 14 13.16 PAVING SLABS ON AGGREGATE BED FOR ROOF PLAZA DECKS (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs used as ballast and/or paving on
More informationSECTION PRECAST CONCRETE PAVERS AND PEDESTAL LOK DOWN SYSTEM
SECTION 07555 PRECAST CONCRETE PAVERS AND PEDESTAL LOK DOWN SYSTEM PART ONE: GENERAL 1.1 SUMMARY A. Concrete paver and pedestal support system with Lok Down devices are to be placed over roofing/waterproofing
More informationSECTION ROOF PEDESTAL PAVER SYSTEM
SECTION 07 76 00 ROOF PEDESTAL PAVER SYSTEM ************************************************************************************************************************ Edit entire master to suit project requirements.
More informationAGA Roof Deck Pavers. AGA Concrete Paver. Technical. Pavers: Hydraulically pressed concrete pavers: 460 tons of pressure.
Cut Sheet AGA Roof Deck Pavers AGA Concrete Paver Overview: AGA Standard sized pavers are manufactured to meet project requirements. Custom: we offer a variety of custom sizes and a mixture of colors and
More informationCONCRETE TILE PAVERS
Section 32 14 13 CONCRETE TILE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for the U.S. is for the installation of concrete tile paving units whose thickness are less than the
More informationROOF PAVER SYSTEM National Distribution SPEC - SECTION 07760
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationReinforced California Architectural Roof Pavers, Pedestal Supported
The following specification refers to the Stepstone, Inc. product known as: Reinforced California Architectural Roof Pavers, Pedestal Supported Stepstone, Inc. also manufactures California Architectural
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationBITUMEN-SET PRECAST CONCRETE PAVING SLABS
SECTION 32 14 13.16 BITUMEN-SET PRECAST CONCRETE PAVING SLABS (1995 MasterFormat Section 02784) NOTE: This guide specification is the U.S. for concrete paving slabs adhered with a neoprene mastic to a
More informationfor Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural
More informationCalifornia Architectural Pavers for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: California Architectural Pavers for Mortar-Set Concrete Tiling Installations Stepstone, Inc. also manufactures California Architectural
More informationIPE WOOD DECK TILES National Distribution SPEC - SECTION 07760
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More information1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels. 3. Insulation. 4. Plaza deck pavers.
SECTION 071413 HOT FLUID APPLIED RUBBERIZED ASPHALT WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Rubberized asphalt waterproofing membrane, reinforced. 2. Molded sheet drainage panels.
More informationNarrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Mortar-Set Concrete Tiling Installations Narrow Modular Pavers are part of the California Architectural
More informationPAVING SLABS ON A CONCRETE BASE
SECTION 32 14 13.16 PAVING SLABS ON A CONCRETE BASE (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs on a sand bed over concrete for pedestrian applications.
More informationSECTION PAVING SLABS ON AN AGGREGATE BASE
SECTION 32 14 13.16 PAVING SLABS ON AN AGGREGATE BASE (1995 MasterFormat Section 02784) NOTE: This guide specification for the U.S. is for paving slabs on a sand bed over a compacted aggregate base for
More informationSECTION PAVING SLABS ON AN AGGREGATE BASE
SECTION 32 14 13.16 PAVING SLABS ON AN AGGREGATE BASE (1995 MasterFormat Section 02784) NOTE: This guide specification for the U.S. is for paving slabs on a sand bed over a compacted aggregate base for
More informationUniversity of New Hampshire Scholars' Repository
University of New Hampshire University of New Hampshire Scholars' Repository Division 07 Thermal and Moisture Protection Chapter 5 Technical Construction and Renovation Standards 1-25-2013 075423 - TPO
More information1. Concrete pavers, with ungrouted joints, over sand base. a. Large precast sections in random mix with smaller concrete pavers
SECTION 32 14 00 - PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specifications Sections, apply
More informationNarrow Modular Pavers (NMP) for Sand-Set Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Sand-Set Installations Narrow Modular Pavers are part of the California Architectural Paver line
More informationReCote Finish System over Concrete
Part 1 General 1.01 GENERAL A. The Master Wall ReCote Finish System for smooth precast and cast in place concrete consists of an acrylic primer and ReCote acrylic finish. When needed an acrylic modified
More informationExpansion Joint Covers
Expansion Joint Covers 07 95 00 (079513) PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Supplementary Conditions and Division-1
More informationSECTION INTERLOCKING CONCRETE PAVERS
SECTION 23 14 13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for concrete paver applications in the U.S. for concrete pavers and bedding sand over a compacted
More informationExpansion Joint Covers (079513)
Expansion Joint Covers 07 95 00 (079513) PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions, Supplementary Conditions and Division-1
More informationSECTION PAVING SLABS ON AN AGGREGATE BASE
Phone 905-655-3311 1-800-655-3430 Email brooklinsales@brooklin.com CAN-slabs on agg base.doc Phone 905-655-3311 1-800-655-3430 Email brooklinsales@brooklin.com SECTION 32 14 13.16 PAVING SLABS ON AN AGGREGATE
More informationSECTION INTERLOCKING CONCRETE PAVERS
SECTION 32 14 13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for concrete paver applications in the U.S. for concrete pavers and bedding sand over a compacted
More informationSECTION FLUID-APPLIED WATERPROOFING
SECTION 07140 FLUID-APPLIED WATERPROOFING PART 1 GENERAL 1.1 SUMMARY A. Section includes fluid applied rubberized asphalt and/or elastomeric membrane waterproofing; and surface dusting and/or protective
More informationSECTION SHEET MEMBRANE WATERPROOFING
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 07 13 00 SHEET MEMBRANE WATERPROOFING A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General
More informationGUIDE SPECIFICATION FOR CONSTRUCTION USING WILLOW CREEK CONCRETE PAVERS
SECTION 23 14 13.13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 2780) GUIDE SPECIFICATION FOR CONSTRUCTION USING WILLOW CREEK CONCRETE PAVERS Note: This guide specification for concrete paver
More informationSECTION UNIT PAVERS
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationTerraClad TM General Specifications
TerraClad TM General Specifications PRODUCT NAMES: Terra cotta Baguettes/Louvers and Related Work MANUFACTURER: Boston Valley Terra Cotta 6860 S. Abbott Road Orchard Park, NY 14127 Phone: 888-214-3655
More informationBison Innovative Products 1975 W. 13 th Ave. Phone February 2012 P.O. Box Toll Free Denver, CO Fax
Bison Innovative Products 1975 W. 13 th Ave. Phone 303-892-0400 February 2012 P.O. Box 40246 Toll Free 800-333-4234 Denver, CO 80204 Fax 303-825-5988 www.bisonip.com info@bisonip.com SECTION 02870 SITE
More informationSECTION THERMOPLASTIC MEMBRANE ROOFING PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07540 - THERMOPLASTIC MEMBRANE ROOFING PART 1 GENERAL 1.01 SECTION INCLUDES A. Mechanically attached system with thermoplastic roofing membrane. B. Insulation, flat and tapered. C. Flashings. D.
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 075423 - THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including Division 00 Bidding Requirements and other Division
More informationGuide Specifications ADP Series SECTION SHEET METAL ROOFING
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Sheet metal roofing panels, metal trim, accessories, fasteners, closures, and sealants. [Specifier Note: Edit paragraph below to suit project requirements.]
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationCorium Brick Rainscreen System Specifications
CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated
More informationSECTION 07530CP EPDM MEMBRANE ROOFING
PART 1 GENERAL 1.1 SUMMARY SECTION 07530CP EPDM MEMBRANE ROOFING A. Section includes: 1. Adhered membrane roofing and flashing 2. Mechanically fastened roof insulation 3. Walkway pads 1.2 ARCHITECTURAL
More informationArchitectural Wall Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Wall Products Guide Specifications FORMED METAL WALL PANELS This Guide Specification is
More information[Project Name] Section [ ]
Page 1 PART 1 - GENERAL 1.1 SECTION INCLUDES 1.1.1 Design, labor, products, equipment and services necessary for interior/exterior Aluminum Facade System (AFS) work, in accordance with the Contract Documents.
More informationA. Omega-Lite aluminum-faced composite panels, air and vapor barrier, attachments and sealants.
Section 07 42 13 Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES A. Omega-Lite aluminum-faced composite panels, air and vapor barrier, attachments and sealants. 1.2 RELATED SECTIONS A. Section 06112 - Framing
More informationSECTION CONCRETE CURBS, GUTTERS AND SIDEWALKS
SECTION 32 16 13 CONCRETE CURBS, GUTTERS AND SIDEWALKS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and required
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationA. The extent of extruded aluminum walkway covers is shown on the Drawings and as specified herein.
SECTION 10530 - EXTRUDED ALUMINUM WALKWAY COVERS PART I - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division
More information1.03 Submittals A. Submit the following in accordance with Section 01300:
Specifications Geofirma Retaining Wall System Part 1 General 1.01 Summary A. Section Includes 1. Work includes furnishing and installing concrete modular block retaining wall units to the lines and grades
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More information1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards
SECTION 07185 TRAFFIC MEMBRANE PART 1 GENERAL 1.1 SECTION INCLUDES A. Traffic membrane, consisting of welded seam PVC waterproofing, over f following surfaces: 1. Decks, balconies, and sun porches 2. Walkways,
More informationGensler 2014/06/16 Hertz Global Headquarters ISSUE FOR BUILDING PERMIT Estero, Florida SECTION
SECTION 072700 VAPOR PERMEABLE AIR BARRIER LIQUID MEMBRANE PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. The Work of this Section, as shown or specified, shall be in accordance with the requirements of the
More informationRECOMMENDED DESIGN SPECIFICATION
RECOMMENDED DESIGN SPECIFICATION SILICONE COATED SPF ROOFING 1 General 1.1 Section Includes A. Silicone coated SPF roofing system, including substrate board, roof insulation boards, foam insulation materials,
More informationSECTION MANUFACTURED ROOF EXPANSION JOINTS
SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION SELF-ADHERING SHEET MEMBRANE WATERPROOFING
SECTION 07 13 26 PART 1 - GENERAL 1.1 SUMMARY A. Scope: 1. Apply waterproofing to: a. Exterior of walls below grade: 1) Waterproofing shall include exterior of walls surrounding elevator pits and sumps.
More informationMaster Specifications for Microcotta November 2017
SECTION 042130 - MICROCOTTA PART 1 - GENERAL 1.1 SUMMARY A. Provide Architectural Microcotta, cast architectural polymer resin units manufactured in accordance with the Contract Documents. 1.2 WORK INCLUDED
More informationGuideline Specification ACRYMAX ARS-1-C Reinforced Composite Elastomeric Membrane System for Concrete Roofs Fluid-Applied Roofing
221 Brooke Street Media, PA 19063 610-566-7470 Fax 610-891-0834 Website www.acrymax.com e-mail info@acrymax.com This document is intended to provide guidelines for the proper specification and application
More informationSPECIFICATION GUIDELINE
Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION EMBEDDED CMU/SPLIT FACE ARCHITECTURAL PRECAST/SITECAST CONCRETE. A. Site Cast or Tilt-Up CMU/Split Face Concrete Panels.
SECTION 03460 EMBEDDED CMU/SPLIT FACE ARCHITECTURAL PRECAST/SITECAST CONCRETE PART 1 GENERAL 1.1 SECTION INCLUDES A. Site Cast or Tilt-Up CMU/Split Face Concrete Panels. B. Shop/Plant Cast CMU/Split Face
More informationSECTION INTERLOCKING PRECAST CONCRETE UNIT PAVERS
SECTION 321413.13 INTERLOCKING PRECAST CONCRETE UNIT PAVERS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interlocking concrete paver units. 2. Sand setting bed. 3. Sand joint
More informationEverGuard Plaza Deck Roofing For Above-Grade Plaza Deck Applications
EverGuard Plaza Deck Roofing For Above-Grade Plaza Deck Applications Specifications Updated: 12/07 Quality You Can Trust Since 1886... From North America s Largest Roofing Manufacturer PLAZA DECK ROOFING
More informationA. The work of this section includes, but is not limited to, the following:
SECTION 07 14 00 FLUID APPLIED WATERPROOFING SYSTEM PART 1: GENERAL 1.1 RELATED DOCUMENTS A. All of the Contract Documents, including General and Supplementary Conditions and Division 01 General Requirements,
More informationStudent Services & Classroom Addition
SECTION 071326 - SELF-ADHERING SHEET WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION SELF-ADHERING SHEET FLASHING
MANUFACTURER S GUIDE SPECIFICATIONS SECTION 076526 SELF-ADHERING SHEET FLASHING 900 Hensley Lane Wylie TX 75098 800-527-7092 www.carlisleccw.com 604129 03.24.15 Carlisle, Flexphalt, Sure-Seal and CAV-GRIP
More informationSECTION RIGID PAVEMENT
SECTION 02750 PART 1 GENERAL RIGID PAVEMENT 1.1 SUMMARY A. Section Includes: 1. Concrete sidewalks. 2. Concrete stair steps. 3. Concrete integral curbs gutters. 4. Concrete parking areas and roads. B.
More informationSpecification Guide and Installation Overview
Specification Guide and Installation Overview PART ONE GENERAL 1.1 SCOPE OF WORK Provide materials, labor, transportation, services and equipment necessary to supply and install Xeripave or Xeribrix as
More informationSECTION THERMOPLASTIC MEMBRANE ROOFING. C. Flashings. D. Roofing cant strips, stack boots, roofing expansion joints, and walkway pads.
McClellan Blakemore Architects New Warehouse Facility for SECTION 07540 THERMOPLASTIC MEMBRANE ROOFING PART 1 GENERAL 1.01 SECTION INCLUDES A. Adhered system with thermoplastic roofing membrane. B. Insulation,
More informationSPECIFICATIONS MODERRA MORTARLESS MASONRY VENEER
SPECIFICATIONS MODERRA MORTARLESS MASONRY VENEER PART 1: GENERAL 1.01 Section Includes A. Product description and definitions. B. Constructing base ledge for concrete wall units. C. Installing modular
More informationSECTION GENERAL REQUIREMENTS PART 1 - GENERAL I 1 GENERAL REQUIRMENTS
SECTION 01 00 00 GENERAL REQUIREMENTS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Summary of Work: 1. General 2. Contract. B. Contract Considerations: 1. Schedule of values. 2. Applications for payment. 3.
More informationSECTION INTERLOCKING CONCRETE PAVEMENT ON A CEMENT TREATED BASE
SECTION 32 14 13 INTERLOCKING CONCRETE PAVEMENT ON A CEMENT TREATED BASE (1995 MasterFormat Section 02780) Note: This guide specification for the U.S. is for concrete pavers on a sand bed with geotextile
More informationArchitectural Roof Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Roof Products Guide Specifications FORMED METAL ROOF AND WALL PANELS This Guide Specification
More informationLS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION
LS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION A. Section Includes B. References C. Quality Assurance D. Submittals E. Delivery, Storage and Handling F. Environmental Conditions G. Summary H. Concrete
More information1.02 DESCRIPTION A. This Section specifies furnishing and installing Surface Applied Detectable/Tactile Warning Surface Tiles where indicated.
SURFACE APPLIED DETECTABLE/TACTILE WARNING SURFACE TILE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions and Division 1 Specifications
More informationST. JOHNS COUNTY ARCH. PROJ. NO SECTION PREFABRICATED ALUMINUM CANOPIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 10530 PREFABRICATED ALUMINUM CANOPIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationProject Name Project # Project Information
SECTION 074229.00 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationBIO-AQUIFER STORM SYSTEM
BIO-AQUIFER STORM SYSTEM Specifications for Construction PART 1 GENERAL 1.01 SECTION INCLUDES A. Providing labor, materials, tools and equipment to furnish and install a permeable concrete paving stone
More informationArchitectural Roof and Wall Products Guide Specifications
Architectural Roof and Wall Products Guide Specifications Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 FORMED METAL WALL PANELS This Guide Specification
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationPART 1 GENERAL 1.1 SECTION INCLUDES. A. Below grade waterproofing and dampproofing 1.2 RELATED SECTIONS 1.3 REFERENCES
HYDROSTAR AG Series HDPE Dampproofing and Drainage Membrane 07 00 00 Thermal and Moisture Protection 07 10 00 Dampproofing 07 13 00 Sheet Waterproofing 07 13 54 Thermoplastic Sheet Waterproofing NOTE TO
More informationCSI GUIDE Countertops
CSI GUIDE Countertops Part 1 General 1.0 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply
More informationA. Division 01 Specification Sections, Drawings, General Conditions, Supplementary General Conditions, and Special Conditions apply to this section.
Note: This guide specification for U.S. applications is for concrete grid units placed on a sand bedding course over a compacted dense-graded aggregate base. The text allows an option of topsoil and grass
More informationLouis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1
Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationCON-DEK ICC-ES ESR-2097 SYSTEM
CON-DEK ICC-ES ESR-2097 SYSTEM Manufacturer Specifications Waterproof Deck Coating for Above Grade Concrete PART I. GENERAL 1.01 Scope A. Provide all labor, materials and equipment necessary to apply the
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationSECTION COMMERCIAL CURB-MOUNT ACRYLIC DOUBLE DOME SKYLIGHTS
SECTION 08620 COMMERCIAL CURB-MOUNT ACRYLIC DOUBLE DOME SKYLIGHTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationArchitectural Roof Products Guide Specifications
Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Roof Products Guide Specifications FORMED METAL ROOF AND WALL PANELS This Guide Specification
More informationSECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof
SECTION 07550 MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof This section is based on the products of MFM Building Products Corp., which is located at: 525 Orange St. P. O. Box 340 Coshocton, OH 43812
More informationSPECIFICATIONS FOR. CEI Composite Materials, LLC Featuring R4000 Rear Back Ventilated Rainscreen System. Section Aluminum Composite Panels
SPECIFICATIONS FOR (1/13 Edition) CEI Composite Materials, LLC Featuring R4000 Rear Back Ventilated Rainscreen System Section 074243 Aluminum Composite Panels (Based upon CEI Composite Materials R4000
More informationSECTION CERAMIC TILE. B. Ceramic tile wall finishes including standard and custom designs.
SECTION 09 30 13 CERAMIC TILE PART 1 GENERAL 1.1 SECTION INCLUDES A. Ceramic tile floor and base finishes. B. Ceramic tile wall finishes including standard and custom designs. 1.2 REFERENCES A. ANSI/TCNA
More informationPhenolic Exterior Wall Cladding
Phenolic Exterior Wall Cladding SECTION 07 42 43 COMPOSITE WALL PANELS This specification includes hidden text for editing for a project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Phenolic wall
More informationSECTION A. ACSE 7 Minimum Loads for Buildings and other Structures.
SECTION 06 12 00 STRUCTURAL INSULATED PANELS ------------------------------------------------------------------------------------------------------------ PART 1- GENERAL ----------------------------- 1.1
More informationSECTION CONCRETE GRID PAVEMENTS (1995 MasterFormat Section 02795)
SECTION 32 14 13.19 CONCRETE GRID PAVEMENTS (1995 MasterFormat Section 02795) Note: This guide specification for U.S. applications is for concrete grid units placed on a sand bedding course over a compacted
More informationSECTION CONCRETE GRID PAVEMENTS (Turfstone) (1995 MasterFormat Section 02795)
SECTION 32 14 13.19 CONCRETE GRID PAVEMENTS (Turfstone) (1995 MasterFormat Section 02795) Note: This guide specification for U.S. applications is for concrete grid units placed on a sand bedding course
More informationSECTION 1 - ETHYLENE-PROPYLENE-DIENE-MONOMER (EPDM) ROOFING
Project Name: Jefferson City Jaycees Fairgrounds Main Building Roof Replacement Project Site Address: 1445 Fairgrounds Road, Jefferson City, MO 65109 Project Contact: Randy Weaver Project Contact phone
More informationSOLAR COATING SYSTEMS ACRYLIC RENOVATION ROOF 4.5. Specification for Built-Up Roofing SUMMARY
SOLAR COATING SYSTEMS ACRYLIC ROOF RENOVATION 4.5 Specification for Built-Up Roofing 07590 PART 1. GENERAL 1.01 SUMMARY NAME ADDRESS A. Furnish and install a seamless, waterproof spray applied elastomeric
More informationGuideline Specifications
Page 1 of 7 PART 1 Guideline Specifications Exterior Aluminum/Composite Wall Panels GENERAL ARROWHEAD 508 SYSTEM Pressure Equalized Rainscreen SECTION 07410 1.01 SUMMARY A. Work of this section included
More informationTURFSTONE PAVERS SECTION CONCRETE GRID PAVEMENTS (1995 MasterFormat Section 02795)
TURFSTONE PAVERS SECTION 32 14 13.19 CONCRETE GRID PAVEMENTS (1995 MasterFormat Section 02795) Note: This guide specification for U.S. applications is for concrete grid units placed on a sand bedding course
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationSECTION WOOD STRIP FLOORING
SECTION 096429 WOOD STRIP FLOORING PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. 1.2 SECTION
More information