A. This Section includes the following: B. Related Sections: The following Sections contain requirements that relate to this Section:

Size: px
Start display at page:

Download "A. This Section includes the following: B. Related Sections: The following Sections contain requirements that relate to this Section:"

Transcription

1 SECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawing and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Handrails. 2. Wall guards. 3. Corner guards. B. Related Sections: The following Sections contain requirements that relate to this Section: Rough Carpentry Gypsum Board Painting. 1.3 QUALITY ASSURANCE A. Installer Qualifications: Engage an experienced Installer who has previously installed wall surface protection systems similar in material, design, and extent to the systems indicated for this Project. B. Fire Performance Characteristics: Provide wall surface protection system components that are identical to those tested in accordance with ASTM E 84 for the fire perfomlance characteristics indicated below. Identify wall surface protection system components with appropriate markings fiom the testing and inspection organization. 1. Flame Spread: 25 or less. 2. Smoke Developed: 450 or less. C. Impact Strength: Provide wall surface protection system conlponents with a minimum iinpact resistance of 25.4 ft. lbs per sq. ft. when tested in accordance with ASTM D 256 (Izod impact, ft. lbs per inch notch). D. Single Source Responsibility: Obtain each color, grade, finish, and type of wall surface protection system component from a single source with resources to provide products of consistent quality in appearance and physical properties without delaying progress of the Work.

2 E. Design Criteria: The drawings indicate the size, profile and dimensional requireillents of wall surface protection system components required and are based on the specific types and n~odels indicated. Wall surface protection system components by other manufacturers may be considered provided deviations in dimensions and profiles are minor and do not change the design concept as judged by the AJE. The burden of proof of equality is on the proposer. 1.4 SUBMITTALS A. General: Submit the following in accordance with Section B. Product data for each wall surface protection system component and installation accessory required, including installation methods for each type of substrate. Provide written data on each required component including physical characteristics, such as durability, resistance to fading, and flame resistance. C. Shop drawings showing locations, extent, and installation details of wall and corner guards, and other protection systems. Show methods of attachment to adjoining construction. D. Samples for Initial Selection: For initial selection of color, pattern and surface texture, provide the manufacturer's standard color chips consisting of actual sections of each vinyl plastic material required showing the full range of materials, colors, and textures available. E. Samples for Verification Purposes: Submit the following samples, prepared from the same material to be used in the Work, for verification of color, pattern, and texture selected and for compliance with requirements indicated: inch long samples of each type of wall and corner guard required. Include examples of joinery, comers, and field splices inch by 6-inch square samples for each rigid sheet of panel type wall surface protection material required. F. Product test reports from a qualified independent testing laboratory showing compliance of wall surface protection system components with requirements indicated based on tests performed by the laboratory within the past five years. G. Maintenance data for wall surface protection system components for inclusion in the Operating and Maintenance Manuals specified in Division PROJECT CONDITIONS A. Environmental Conditions: Do not install wall surface protection system components until the space is enclosed and weatherproof and until the ambient temperature within the building is maintained at not less than 70 deg F (21 deg C) for not less than 72 hours prior to beginning of the installation. Do not install rigid plastic wall surface protection systems until that temperature has been attained and is stabilized. 1.6 MAINTENANCE

3 A. Maintenance Instructions: Provide the manufacturer's instructions for maintenance for installed work. Include recommended methods and frequency for maintaining optimum condition under anticipated traffic and use conditions. Include precautions against cleaning materials and methods that may be detrimental to finishes and performance. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following suggested manufacturers or equal: 1. Balco Metalines, P.O. Box 17249, Wichita, Kansas ; telephone: PC, P.O. Box 406, Musltego, WI 53150; telephone: Pawling Corporation, P.O. Box 200, Wassic, New York 12592; telephone: MATERIALS A. Rigid Plastic Material: Extruded, textured, chemical-and stain-resistant, high-impact, polyvinyl chloride (PVC) or acrylic modified vinyl plastic, thickness as indicated. Comply with specified requirements of ASTM D 256 for impact resistance and ASTM E 84 for flame spread and smolte developed characteristics. B. Colors and Textures of Plastic Material: Provide extruded plastic material that matches selections made by the Architect from the manufacturer's full range of standard colors and textures. C. Aluminum Extrusions: Provide alloy and temper recommended by the manufacturer for the type of use and finish indicated, but with not less than.the strength and durability properties specified in ASTM B 22 1 for 6063-T5. D. Fasteners: Provide aluminum, nonmagnetic stainless steel, or other noncorrosive metal screws, bolts, and other fasteners compatible with aluminum components, hardware, anchors, and other items being fastened. Use theft-proof fasteners where exposed to view. A. Impact-resistant Plastic Handrails: Provide assembly consisting of a snap-on-type plastic cover installed over a continuous aluminum retainer mounted at height indicated. 1. Cover shall be rigid, extruded, impact-resistant plastic, minimum inch thick, in dimensions and profiles indicated. 2. Retainer: Manufacturer's standard continuous, one-piece, extruded aluminum retainer, minimum inch thick

4 a. Mounting Brackets: Extended mounting on injection-molded plastic mounting brackets. 3. Accessories: Provide prefabricated, injection molded end caps and inside and outside comers with concealed splices, cushions, mounting hardware and other accessories as required. a. End caps and inside and outside comers shall match plastic cover color and shall be field adjustable for close alignment with snap-on plastic covers. B. Acceptable Products: 1. Balco- VR PC Pawling- BR C. Locate in corridor as indicated on drawings 2.4 WALL GUARDS A. B~uilper Rail Type Wall Guards: Provide bumper rail wall guard assembly consisting of a snap-ontype plastic cover installed over a continuous aluminum retainer mounted at height indicated. 1. Cover shall be rigid, extruded, impact-resistant plastic, ininin~~~m inch thick, in dimensions and profiles indicated. 2. Retainer: Manufacturer's standard continuous, one-piece, extruded al~uninum retainer, minimum inch thick. b. Mounting Type: Surface-mounted flush on wall. 3. Accessories: Provide prefabricated, injection molded end caps and inside and outside comers with concealed splices, cushions, mounting hardware and other accessories as required. a. End caps and inside and outside comers shall match plastic cover color and shall be field adjustable for close alignment with snap-on plastic covers. B. Acceptable Products: I. Balco- Type VB PC Pawling- WG-6. C. Locate in corridor as indicated on drawings

5 2.5 CORNERGUARDS A. Surface-Mounted, Resilient Plastic Corner Guards: Provide surface-mounted, resilient plastic corner guard assembly consisting of snap-on-type plastic cover installed over a continuous aluminum retainer, heights as indicated. 1. Cover shall be rigid, impact-resistant, plastic, minimum inch thick, in dimensions and profiles indicated. a. Comer Radius: '/4 inch. 2. Retainer: Manufacturer's standard continuous, one-piece, extruded alun~inun~ retainer, minimum inch thick. 3. Accessories: Provide prefabricated, injection-molded top cap and alumin~un base with concealed splices, cushions, mounting hardware, and other accessories as required. a. Top caps shall match color of plastic covers and shall be field adjustable for close alignment with snap-on plastic covers. b. Acceptable Products: (See drawings for different size locations.) 1. Balco- Type CGS PC- # Pawling- CGS-3. B. Locate in corridor as indicated on drawings. 2.6 FABRICATION A. General: Fabricate wall protection systems to comply with requirements indicated for desig~, dimensions, details, finish, and member sizes, including wall thicknesses of components. B. Preassemble components in the shop to the greatest extent possible to minimize field assembly. Disassemble only as necessary for shipping and handling. C. Fabricate conlponents with tight seams and joints with exposed edges rolled. Provide surfaces fi-ee of evidence of wrinkling, chipping, uneven coloration, dents, and other imnperfections. Fabricate members and fittings to produce flush, smooth, and rigid hairline joints. D. Brackets, Flanges, Fittings, and Anchors: Provide wall brackets, flanges, miscellaneous fittings, and anchors for interconnection of members to other construction. E. Provide inserts and other anchorage devices for connection components to concrete or masonry. Fabricate anchoring devices to be capable of withstanding imposed loads. Coordinate anchoring devices with the supporting structure. 2.7 FINISHES

6 A. Aluminum Mill Finish on Concealed Hardware: AA-MI0 (Mechanical Finish: as fabricated, unspecified). B. Textured, Chemical and Stain Resistant, High-Impact Polyvinyl Chloride or Acrylic modified PVC plastic color throughout finish. Architect to select manufacturers fbll range of colors and textures. PART 3 - EXECUTION 3.1 EXAMINATION A. Examine areas and conditions in which wall surface protection components and wall protection systems will be installed. 3.2 PREPARATION A. General: Prior to installation, clean substrate to remove dust, debris, and loose particles. 3.3 INSTALLATION A. General: Install wall surface protection units plumb, level, and tn~e to line without distortions. 1. Do not use materials with chips, cracks, voids, stains, or other defects that might be visible in the finished work. B. Install aluminum retainers, mounting brackets, and other accessories in strict accordance with the manufacturer's instructions. 1. Where splices occur in horizontal runs of over 20 feet, splice aluminum retainer and plastic cover at different locations along the run. 3.4 CLEANING A. General: Immediately upon completion of installation, clean plastic covers and accessories using standard ammonia based household cleaning agent. Clean metal components in accordance with the manufacturer's recommendations. B. Remove excess adhesive using methods and materials recommended by manufacturer. C. ~emove surplus materials, rubbish, and debris resulting from installation upon conlpletion of work and leave areas of installation in neat, clean conditions. END OF SECTION

7 SECTION PLRE PROTECTION SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Fire extinguishers. 2. Fire extinguisher cabinets. 1.3 SUBMITTALS A. General: Submit the following in accordance with Conditions of Contract and Division 01 Specification Sections. B. Product data for each type of product specified. For fire extinguisher cabinets include rough-in dimensions, details showing mounting methods, relationships of box and trim to surrounding construction, door hardware, cabinet type and materials, trim style, door const~~~ction, panel style, and materials. C. Sanlples for initial selection purposes in fornl of n~anufacturer's color charts showing full range of colors available for those units with factory-applied color finishes. 1.4 QUALITY ASSURANCE A. Single-Source Responsibility: Obtain fire extinguishers and cabinets from one source from a single manufacturer. B. UL-Listed Products: Fire extinguishers UL-listed and bear UL "Listing Mark" for type, rating, and classification of extinguisher. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following suggested manufacturers or equal: FIRE PROTECTION SPECIALTIES

8 Manufacturer J.L. Industries Bloomington, MN (61 2) Larsen's Mfg. Co. Minneapolis, MN (612) Modem Metal Products Owatonna, MN (507) Recessed Cabinet Panorama 1025 P 42 Gemini ALG2409-R2 Vertical, White with Black Letters 1 00 Series Tonna T102(6)R-1 AL Vertical, White with Black Letters 2.2 FIRE EXTINGUISHERS A. General: Provide fire extinguishers for each extinguisher cabinet or wall bracket locations indicated on drawings, in colors and finishes selected by Architect from manufacturer's standard, which comply with requirements of governing authorities. 1. Fill and service extinguishers to comply with requirements of governing authorities and manufacturer. B. Multipurpose Dry Chemical Type: UL-rated 4-A:60-B:C, 10-lb. nominal capacity, in enameled steel container. 2.3 FIRE EXTINGUISHER CABINETS B. General: Provide fire extinguisher cabinets where indicated, of suitable size for housing fire extinguishers of types and capacities indicated. C. Construction: Manufacturer's standard enameled steel box, with trim, frame, door, and hardware to suit cabinet type, trim style, and door style indicated. Weld all joints and grind smooth. Miter and weld perimeter door frames. PART 3 - EXECUTION 3.1 INSTALLATION A. Install items included in this section in locations and at mounting heights indicated, or if not indicated, at heights to comply with applicable regulations of governing authorities. 1. Prepare recesses in walls for fire extinguisher cabinets as required by type and size of cabinet and style of trim and to comply with manufacturer's instructions. 2. Securely fasten mounting brackets and fire extinguisher cabinets to stiucture, square and plumb, to comply with manufacturer's instructions. END OF SECTION FlRE PROTECTION SPECIALTIES

SECTION IMPACT RESISTANT WALL PROTECTION

SECTION IMPACT RESISTANT WALL PROTECTION SECTION 10265 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work under this Section shall include all materials and installation necessary to provide Impact-Resistant Wall Protection including Wall guards,

More information

B. Samples for Initial Selection: For each type of impact-resistant wall protection unit indicated.

B. Samples for Initial Selection: For each type of impact-resistant wall protection unit indicated. SECTION 102600 - WALL AND DOOR PROTECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION DOOR AND WALL PROTECTION

SECTION DOOR AND WALL PROTECTION PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10 26 00 DOOR AND WALL PROTECTION A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification

More information

A. Section ʻRough Carpentryʼ for wood blocking and grounds for corner guards.

A. Section ʻRough Carpentryʼ for wood blocking and grounds for corner guards. SECTION 10265 PART ONE GENERAL 1.1 SECTION INCLUDES A. Corner guards. 1.2 RELATED SECTIONS A. Section 06120 ʻRough Carpentryʼ for wood blocking and grounds for corner guards. 1.3 RELATED DOCUMENTS A. Drawings

More information

SECTION WALL AND DOOR PROTECTION

SECTION WALL AND DOOR PROTECTION PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to

More information

CHAIR RAIL. C/S Acrovyn Model SCR-48

CHAIR RAIL. C/S Acrovyn Model SCR-48 10260-1 CHAIR RAIL C/S Acrovyn Model SCR-48 Part 1 - General 1.01 Summary A. This section includes the following types of wall protection systems: 1. Crash Rails B. Related sections: The following sections

More information

Northpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017

Northpointe Renovation EPN #1701 F/A Project #17027 September 8, 2017 SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.

SECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate. SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Welded stainless steel railing systems. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete; coordination with substrate.

More information

A. This Section includes the following: 1. Aluminum pipe and tube handrails and railings.

A. This Section includes the following: 1. Aluminum pipe and tube handrails and railings. SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

SECTION ALUMINUM HANDRAIL SYSTEMS

SECTION ALUMINUM HANDRAIL SYSTEMS SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American

More information

PRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B

PRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B SECTION 05 5213 - PIPE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

PIPE AND TUBE RAILINGS

PIPE AND TUBE RAILINGS SECTION 05521 - PIPE AND TUBE RAILINGS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Trex Commercial Products page Metal Railing

Trex Commercial Products page Metal Railing SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post Rail (Glass). D. Tensiline Railings (Cable). E. Track Rail (Glass).

More information

SECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Post

More information

OREGON STATE UNIVERSITY GOSS STADIUM - CLUB AND LOGE SEATING CORVALIS, OREGON SECTION WALL AND DOOR PROTECTION

OREGON STATE UNIVERSITY GOSS STADIUM - CLUB AND LOGE SEATING CORVALIS, OREGON SECTION WALL AND DOOR PROTECTION SECTION 10 2600 - WALL AND DOOR PROTECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

A. Atlantic Railing Series with Mushroom Top and Square Pickets

A. Atlantic Railing Series with Mushroom Top and Square Pickets 100 Series-A1-A10 PART 1 General 1.1 SECTION INCLUDES A. Atlantic Railing Series with Mushroom Top and Square Pickets 1.2 RELATED SECTIONS A. Section 05510-Metal Stairs: Metal Handrails other than those

More information

Northpointe Renovation EPN #1701 F/A Prroject #17027 September 8, 2017

Northpointe Renovation EPN #1701 F/A Prroject #17027 September 8, 2017 SECTION 101423.16 - ROOM-IDENTIFICATION PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY 1.3 PERFORMANCE REQUIREMENTS

SECTION PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY 1.3 PERFORMANCE REQUIREMENTS SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION HANDRAILS AND RAILINGS. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Classic Railings (Picket). B. GridGuard Railings (Mesh). C. Invisirail

More information

SECTION PIPE AND TUBE RAILINGS

SECTION PIPE AND TUBE RAILINGS SECTION 055213- PIPE AND TUBE RAILINGS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Section PANEL SIGNAGE

Section PANEL SIGNAGE Section 10 14 23 PANEL SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including FDOT DIVISION I GENERAL REQUIREMENTS & COVENANTS Specification Sections,

More information

SECTION ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH GLASS INFILLS

SECTION ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH GLASS INFILLS 1 SECTION 05 7310 ALUMINUM HANDRAIL AND RAILING SYSTEMS WITH GLASS INFILLS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

SECTION ALUMINUM RAILINGS

SECTION ALUMINUM RAILINGS SECTION 05522 ALUMINUM RAILINGS PART 1 GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Aluminum pipe and tube railings. B. Related Sections include the following: 1. Division 5 Section "Ornamental

More information

DIVISION 10 SPECIALTIES SECTION METAL LOCKERS

DIVISION 10 SPECIALTIES SECTION METAL LOCKERS DIVISION 10 SPECIALTIES SECTION 10 51 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

PRESTON HEALTH SERVICES ARCHITECT'S NO. 2700

PRESTON HEALTH SERVICES ARCHITECT'S NO. 2700 SECTION 09 5113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS

SECTION FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS Page 1 of 17 SECTION 11 4600 FOOD DISPENSING EQUIPMENT- SNEEZE GUARDS AND PARTITION POSTS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and

More information

MASTERSPEC - SHORT FORM. B. See Division 5 Section "Metal Stairs" for steel tube railings associated with metal stairs.

MASTERSPEC - SHORT FORM. B. See Division 5 Section Metal Stairs for steel tube railings associated with metal stairs. SECTION 05721 - ORNAMENTAL RAILINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Glass supported railings. B. See Division 5 Section "Metal Stairs" for steel tube railings associated

More information

A. This Section includes the following types of visual display boards: 1. Porcelain enamel markerboards (for liquid chalk).

A. This Section includes the following types of visual display boards: 1. Porcelain enamel markerboards (for liquid chalk). SECTION 10100 VISUAL DISPLAY BOARDS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION AWNINGS

SECTION AWNINGS SECTION 10 73 13 AWNINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Fixed metal awnings. 1.2 DEFINITIONS A. Awning: An architectural projection that provides weather protection,

More information

DIVISION 10 SPECIALTIES SECTION OPERABLE PARTITIONS

DIVISION 10 SPECIALTIES SECTION OPERABLE PARTITIONS DIVISION 10 SPECIALTIES SECTION 10 22 26 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION (10705) EXTERIOR SUN CONTROL DEVICES

SECTION (10705) EXTERIOR SUN CONTROL DEVICES 10 71 13 SECTION (10705) EXTERIOR SUN CONTROL DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

DIMENSIONAL LETTER SIGNAGE

DIMENSIONAL LETTER SIGNAGE SECTION - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this

More information

SECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces.

SECTION Temperature Change: 120 deg F, ambient; 180 deg F, material surfaces. PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Handrails and guardrails. 1.2 PERFORMANCE REQUIREMENTS A. General: In engineering railings to withstand structural loads indicated, determine

More information

Superior Aluminum Guide Specification 10/4/2016 Non-Welded Aluminum Pipe Railing

Superior Aluminum Guide Specification 10/4/2016 Non-Welded Aluminum Pipe Railing The following specification has been developed by: Superior Aluminum Products 555 East Main Street Russia, Ohio 45363-0430 to assist Architects and Designers in the specification of Non Welded Concealed

More information

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.

K. ASTM F436- Standard Specification for Hardened Steel Washers; 2011. DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:

More information

Suggested Specification SECTION Pawling Pro-Tek Model WG-8EXT

Suggested Specification SECTION Pawling Pro-Tek Model WG-8EXT Suggested Specification SECTION 10 26 16 Pawling Pro-Tek Model WG-8EXT PART 1 GENERAL 1.01 SUMMARY A. This section includes the following wall protection system: 1. Bumper Guards B. Related Sections 1.

More information

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017

PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017 SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS

SECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American Architectural Manufacturers

More information

SECTION MISCELLANEOUS METALS

SECTION MISCELLANEOUS METALS PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications

More information

Louis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1

Louis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1 Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions

More information

B. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work.

B. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work. SECTION 10 5113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

SECTION MECHANICALLY ASSISTED MOBILE STORAGE SHELVING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION MECHANICALLY ASSISTED MOBILE STORAGE SHELVING PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 10560 MECHANICALLY ASSISTED MOBILE STORAGE SHELVING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and

More information

1. Manufacturer's product lines of railings assembled from standard components.

1. Manufacturer's product lines of railings assembled from standard components. SECTION 057300- DECORATIVE METAL RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementmy Conditions and Division 01 Specification

More information

ST. JOHNS COUNTY ARCH. PROJ. NO SECTION PREFABRICATED ALUMINUM CANOPIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS

ST. JOHNS COUNTY ARCH. PROJ. NO SECTION PREFABRICATED ALUMINUM CANOPIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 10530 PREFABRICATED ALUMINUM CANOPIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

North Hanover Township School District North Hanover Township, New Jersey

North Hanover Township School District North Hanover Township, New Jersey SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

A. Glass Railing Series with Mushroom Top Cap with Glass Panel Infill.

A. Glass Railing Series with Mushroom Top Cap with Glass Panel Infill. 100 Series Bayview ( Two-Line) Glass Rail-A1 Top Cap PART 1 General 1.1 SECTION INCLUDES A. Glass Railing Series with Mushroom Top Cap with Glass Panel Infill. 1.2 RELATED SECTIONS A. Section 03300 Cast-

More information

PIPE AND TUBE RAILINGS. Evansville Christian High School RELATED DOCUMENTS 1.1

PIPE AND TUBE RAILINGS. Evansville Christian High School RELATED DOCUMENTS 1.1 SECTION 055213 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this

More information

RAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012

RAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012 SECTION 10200 - LOUVERS AND VENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION DECORATIVE METAL AND GLASS RAILING

SECTION DECORATIVE METAL AND GLASS RAILING SECTION 05 73 00 DECORATIVE METAL AND GLASS RAILING PART 1 GENERAL 1.1 SUMMARY A) This section includes both standard and custom handrails as shown in the contract drawings. B) These include aluminum,

More information

SECTION METAL STAIRS

SECTION METAL STAIRS SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 102239 - FOLDING PANEL PARTITIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

University Apartments on Brooklyn PROJECT MANUAL

University Apartments on Brooklyn PROJECT MANUAL Section 122100 Horizontal Louver Blinds University Apartments on Brooklyn PART 1 - GENERAL 1.1 SECTION INCLUDES A. Horizontal slat louver blinds. B. Operating hardware. 1.2 RELATED SECTIONS A. Section

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 055113 - METAL PAN STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec

SECTION ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec SECTION 05720 ARCHITECTURAL GLASS HANDRAIL AND RAILINGS 3-Line Glass Rail Railing Spec PART 1 - GENERAL 1.01 WORK INCLUDED A. Furnish and install [aluminum] railings and components. 1.02 REFERENCE A. American

More information

Framed Decorative Panel Systems

Framed Decorative Panel Systems Note: This document contains information and notes in hidden text. If you need assistance to view & hide text, instructions are at this link: http://www.marlite.com/hidden-notes-instructions.aspx Delete

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Architectural Wall Products Guide Specifications

Architectural Wall Products Guide Specifications Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 Architectural Wall Products Guide Specifications FORMED METAL WALL PANELS This Guide Specification is

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 055213 - PIPE AND TUBE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

DIVISION VIII - DOORS AND WINDOWS

DIVISION VIII - DOORS AND WINDOWS DIVISION VIII - DOORS AND WINDOWS SECTION 08121 INTERIOR ALUMINUM DOORS, DOOR FRAMES, AND OFFICE FRONT FRAMING (SOLUTIONS II SYSTEM) PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established

More information

SECTION ORNAMENTAL ALUMINUM RAILING

SECTION ORNAMENTAL ALUMINUM RAILING SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Pipe Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in concrete.

More information

1. Standard two tier metal lockers and metal base.

1. Standard two tier metal lockers and metal base. SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

A. Access doors and frames are part of an access door and frame allowance.

A. Access doors and frames are part of an access door and frame allowance. SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY

SECTION ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY 3-PART SPEC ORNAMENTAL ALUMINUM RAILINGS PART 1 - GENERAL 1.01 SUMMARY SECTION 05720 A. Section Includes: a. Solutions aluminum extruded shape top rail, square or round balustrade & rectangular bottom

More information

SECTION PANEL AND POST AND PYLON SIGNAGE. 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs.

SECTION PANEL AND POST AND PYLON SIGNAGE. 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs. PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs. 1.2 PERFORMANCE REQUIREMENTS A. Structural

More information

SECTION MANUFACTURED ROOF EXPANSION JOINTS

SECTION MANUFACTURED ROOF EXPANSION JOINTS SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.

1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces. SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION SERIES ALL GLASS ENTRANCES

SECTION SERIES ALL GLASS ENTRANCES 1 SECTION 08 4210 1200 SERIES ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1.

More information

COUNTY OF KINGS KINGS COUNTY JAIL EXPANSION PHASE III

COUNTY OF KINGS KINGS COUNTY JAIL EXPANSION PHASE III SECTION 101419 - DIMENSIONAL CHARACTER SIGNAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

ARCHITECTURAL SPECIFICATIONS

ARCHITECTURAL SPECIFICATIONS ARCHITECTURAL SPECIFICATIONS CIG JAN PRODUCTS LTD VISUAL DISPLAY BOARDS Part 1-General 1.01 RELATED DOCUMENT A. The provision of the General Conditions. Supplementary Conditions and the Sections included

More information

SECTION FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES

SECTION FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES SECTION 081613 FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

SECTION DIRECTORIES

SECTION DIRECTORIES PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 13 00 DIRECTORIES SPEC WRITER NOTES: 1. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 095133 - ACOUSTICAL METAL PAN CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

SECTION EXPANSION CONTROL

SECTION EXPANSION CONTROL SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

SECTION ACCORDION FOLDING PARTITIONS

SECTION ACCORDION FOLDING PARTITIONS PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable

More information

B. Polyethylene samples shall be submitted for Owner approval of color and quality.

B. Polyethylene samples shall be submitted for Owner approval of color and quality. Glass Rail ENGINEERED DASHERBOARD SPECIFICATIONS PART 1 - GENERAL 1.01 PROJECT SCOPE A. Contractor shall furnish and install one complete set of steel framed dasherboards as indicated on the drawings and

More information

Marlite Guide Specification 2/24/2017 Surface Systems - MAP375 System SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.

Marlite Guide Specification 2/24/2017 Surface Systems - MAP375 System SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1. Note: This document contains information and notes in hidden text. If you need assistance to view & hide text, instructions are at this link: http://www.marlite.com/hidden-notes-instructions.aspx Delete

More information

LINEAR METAL CEILINGS Section

LINEAR METAL CEILINGS Section PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

More information

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.

C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish. SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SPECIFICATIONS: Architectural Aluminum Railings

SPECIFICATIONS: Architectural Aluminum Railings PART ONE: GENERAL 1.1 SUMMARY SPECIFICATIONS: Architectural Aluminum Railings A. Work in this section includes custom and standard Interior and Exterior aluminum railings and guardrails. 1.2 PERFORMANCE

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-10 26 00 (August 2017) Change 2-08/18 --------------------------- Preparing Activity: USACE Superseding UFGS-10 26 00(August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS

More information

Division 8 Section "Flush Wood Doors" for louvers in wood doors. Division 15 Sections for louvers that are a part of mechanical equipment.

Division 8 Section Flush Wood Doors for louvers in wood doors. Division 15 Sections for louvers that are a part of mechanical equipment. 0 0 0 0 0 SECTION 000 - LOUVERS AND VENTS PART GENERAL RELATED DOCUMENTS EASTLAKE FIRE STATION REPLACEMENT HILLSBOROUGH COUNTY CIP # Drawings and general provisions of the Contract, including General and

More information

Multi-Institutional Academic Health Science & Research Center Evansville, IN

Multi-Institutional Academic Health Science & Research Center Evansville, IN SECTION 05 5117 ALTERNATING TREAD STEEL STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Glenlake Modular Railing System

SECTION ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Glenlake Modular Railing System SECTION 05 5200 ARCHITECTURAL ORNAMENTAL HANDRAILS AND RAILINGS Glenlake Modular Railing System PART 1 GENERAL 1.01 WORK INCLUDED A. Furnish and/or install post supported stainless steel railings and components.

More information

Attachment A-Flagpole(s) Specifications

Attachment A-Flagpole(s) Specifications Attachment A-Flagpole(s) Specifications PART 1-GENERAL 1.1 SCOPE A. The scope of work includes the removal of existing flagpole(s) and associated concrete bases, and installation of a new flagpole(s) and

More information

SECTION RESILIENT SHEET FLOORING

SECTION RESILIENT SHEET FLOORING SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.

More information

SECTION EXPANSION CONTROL

SECTION EXPANSION CONTROL SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

SECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN

SECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN SECTION 08350 MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions

More information

SECTION FLOOR MATS AND FRAMES

SECTION FLOOR MATS AND FRAMES Section 12484 Floor Mats and Frames SECTION 12484 - FLOOR MATS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

Architectural Roof and Wall Products Guide Specifications

Architectural Roof and Wall Products Guide Specifications Architectural Roof and Wall Products Guide Specifications Western States Metal Roofing 901 W. Watkins St. Phoenix, AZ 85007 PH: 602-495-0048 FX: 602-261-7726 FORMED METAL WALL PANELS This Guide Specification

More information

SECTION EXPANSION CONTROL

SECTION EXPANSION CONTROL SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

A. The extent of extruded aluminum walkway covers is shown on the Drawings and as specified herein.

A. The extent of extruded aluminum walkway covers is shown on the Drawings and as specified herein. SECTION 10530 - EXTRUDED ALUMINUM WALKWAY COVERS PART I - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division

More information

SECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.

SECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware. 1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders

More information

COMPOSITESIDING

COMPOSITESIDING SECTION 074643 COMPOSITE SIDING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

SOLAR SHADING SYSTEMS - Manual Solar Shade SECTION ROLLER WINDOW SHADES

SOLAR SHADING SYSTEMS - Manual Solar Shade SECTION ROLLER WINDOW SHADES PART 1 - GENERAL SECTION 122413 - ROLLER WINDOW SHADES 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION ORNAMENTAL ALUMINUM RAILING

SECTION ORNAMENTAL ALUMINUM RAILING SECTION 05730 ORNAMENTAL ALUMINUM RAILING PART 1 GENERAL 1.1 SECTION INCLUDES A. Decorative Wire Rope Railing 1.2 RELATED SECTIONS A. Section 03300 Cast-In-Place Concrete: Placement of sleeves cast in

More information

# DAYTONA BEACH PIER BUILDING RESTORATION 06/10

# DAYTONA BEACH PIER BUILDING RESTORATION 06/10 SECTION 055000 - METAL FABRICATIONS PART 1 - PRODUCTS 1.1 METALS A. Ferrous Metals: 1. Steel Plates, Shapes, and Bars: ASTM A 36/A 36M. 2. Stainless-Steel Bars and Shapes: ASTM A 276, Type 304. 3. Rolled-Steel

More information

SECTION METAL LOCKERS

SECTION METAL LOCKERS PART 1 GENERAL 1.1 DESCRIPTION SECTION 10 51 13 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other items or paragraphs not applicable

More information

SECTION HVAC GRAVITY VENTILATORS

SECTION HVAC GRAVITY VENTILATORS SECTION 23 37 23 HVAC GRAVITY VENTILATORS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Specifications for FL-100 Soffit Panel

Specifications for FL-100 Soffit Panel Union Corrugating Company Specifications for FL-100 Soffit Panel SECTION 07410 METAL SOFFIT PANELS PART 1 GENERAL 1.1 DESCRIPTON A. Section Includes: 1. Preformed metal soffit panel system 2. Associated

More information