DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS

Transcription

1 0 Most Widely Accepted and Trusted ICC-ES Listing Report ICC-ES 000 (800) (562) ELC-4027 Issued 07/2017 This listing is subject to renewal 07/2018. DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: AC200+ ADHESIVE ANCHOR SYSTEM IN CRACKED AND UNCRACKED CONCRETE Look for the trusted marks of Conformity! 2014 Recipient of Prestigious Western States Seismic Policy Council (WSSPC) Award in Excellence A Subsidiary of ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recoendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright 2018 ICC Evaluation Service, LLC. All rights reserved.

2 ICC-ES Listing Report (800) (562) ELC-4027 Issued July 2017 Revised February 2018 This listing is subject to renewal July A Subsidiary of the International Code Council CSI: DIVISION: CONCRETE Section: Concrete Anchors Product Certification System: DIVISION: METALS Section: Post-Installed Concrete Anchors The ICC-ES product-certification system includes evaluating reports of tests of standard manufactured product, prepared by accredited testing laboratories and provided by the listee, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the listee s quality system. Product: AC200+ Adhesive Anchor System in Cracked and Uncracked Concrete Listee: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND (800) anchors@dewalt.com Compliance with the following standards: Annex D, Anchorage, of CSA A , Design of Concrete Structures, CSA Group. Compliance with the following codes: AC200+ adhesive anchor system in cracked and uncracked, as described in this listing report, are in conformance with CSA A , Annex D, as referenced in the applicable section of the following code edition: National Building Code of Canada 2015 Applicable Section: Division B, Part 4, Section Description of adhesive anchor system: The AC200+ adhesive anchor system comprised of AC200+ two-component adhesive filled in cartridges, static mixing nozzles, dispensing tools, hole cleaning equipment, and adhesive injection accessories. The AC200+ adhesive may be used with continuously threaded steel rods or deformed steel reinforcing bars. The primary components of the AC200+ adhesive anchor system, including the AC200+ adhesive cartridge, static mixing nozzle, and steel anchor elements, are shown in Figure 1. Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recoendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2018 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 15

3 ELC-4027 Most Widely Accepted and Trusted Page 2 of 15 DISPENSING TOOL REINFORCING BAR CARTRIDGES STATIC MIXING NOZZLE THREADED ROD FIGURE 1 AC200+ ADHESIVE ANCHOR SYSTEM INCLUDING TYPICAL STEEL ANCHOR ELEMENTS AC200+ adhesive two components are kept separate by means of a labelled dual-cylinder cartridge. The two components combine and react when dispensed through a static mixing nozzle, supplied by DEWALT, which is attached to the cartridge. AC200+ is available in cartridge: 10-ounce (280 ml), 12-ounce (345 ml) and 28-ounce (825 ml). Each cartridge label is marked with the adhesive expiration date. The shelf life, as indicated by the expiration date, applies to an unopened cartridge stored in a dry, dark, and cool environment. Hole cleaning equipment is comprised of steel wire brushes supplied by DEWALT, and air blowers which are shown in Figure 3 of this report. AC200+ adhesive must be dispensed with manual dispensers, pneumatic dispensers, or electric powered dispensers supplied by DEWALT. Identification: Installation: AC200+ adhesive is identified by packaging labelled with the company s name (DEWALT) and address, anchor name, the lot number, the expiration date, listing report number (ELC-4027), and the ICC-ES listing mark. Threaded rods, nuts, washers, and deformed reinforcing bars are standard steel anchor elements and must conform to applicable national or international specifications as set forth in Tables 2 and 3 of this report or equivalent. The installation parameters are illustrated in Figure 4 and Table 1. Installation of the AC200+ adhesive anchor system must conform to the manufacturer s printed installation instructions (MPII) included in each unit package as described in Figure 3. The adhesive anchor system may be used for upwardly inclined orientation applications (e.g. overhead). Upwardly included and horizontal orientation applications are to be installed using piston plugs for the 5 / 8- inch through 1 1 / 4-inch (M16 through M30) diameter threaded steel rods and No. 5 through No. 10 (14 through 32 ) steel reinforcing bars, installed in the specified hole diameter, and attached to the mixing nozzle and extension tube supplied by DEWALT as described in Figure 3 in this report. Upwardly included and horizontal orientation installation for the 3 / 8-inch and 1 / 2-inch (M10 and M12) diameter threaded steel rods, and No. 3 and No. 4 (10 and 12 ) steel reinforcing bars may be injected directly to the end of the hole using extension tubing attached to the mixing nozzle with a hole depth h 0 10 (250 ). Installation of anchors in horizontal or upwardly inclined orientations shall be fully restrained from movement throughout the specified curing period through the use of temporary wedges, external supports, or other methods. Where temporary restraint devices are used, their use shall not result in impairment of the anchor shear resistance The DEWALT drilling systems in Figure 2 collect and remove dust with a HEPA dust extractor during the hole drilling operation in dry base materials using haer-drills (see Step 1 of the manufacturer s published installation instructions in Figure 3).

4 ELC-4027 Most Widely Accepted and Trusted Page 3 of 15 FIGURE 2 EXAMPLES DEWALT DUST REMOVAL DRILLING SYSTEMS WITH HEPA DUST EXTACTORS FOR ILLUSTRATION

5 ELC-4027 Most Widely Accepted and Trusted Page 4 of 15 FIGURE 3 MANUFACTURER S PRINTED INSTALLATION INSTRUCTIONS (MPII)

6 ELC-4027 Most Widely Accepted and Trusted Page 5 of 15 FIGURE 3 MANUFACTURER S PUBLISHED INSTALLATION INSTRUCTIONS (MPII) (Continued)

7 ELC-4027 Most Widely Accepted and Trusted Page 6 of 15 Anchor setting information: FIGURE 4 INSTALLATION PARAMETERS FOR THREADED RODS AND REINFORCING BARS Ultimate Limit States Design: TABLE 1 INSTALLATION TORQUE SUBJECT TO EDGE DISTANCE For anchors that will be torqued during installation, the maximum torque, T max, must be reduced for edge distances less than the values given in Tables 5, 8, 11 and 14, as applicable. T max is subject to the edge distance, c min, and anchor spacing, s min, and shall comply with the following requirements: INSTALLATION TORQUE SUBJECT TO EDGE DISTANCE NOMINAL ANCHOR SIZE, d #5 to #8 M16 to M24 ø14to ø25 ( 5 / 8 in. to 1 in.) #9 to #10 M27 to M30 ø28 to ø32 (1 1 / 4 in.) MINIMUM EDGE DISTANCE, c min 44.5 (1.75 in.) 70 (2.75 in.) For values of T max, see Figure 2 of this report. MINIMUM ANCHOR SPACING, s min 5d MAXIMUM TORQUE, T max 0.45 T max Design resistance of anchors for compliance with the 2015 NBCC must be determined in accordance with CSA A Annex D, and this listing report. Design parameters are provided in Table 2 through 15 of this listing report are based on the 2015 NBCC (CSA A ). The limit states design of anchors must comply with CSA A D.5.1, except as required in CSA A D Material resistance factors must be c = 0.65 and s = 0.85 in accordance with CSA A Sections and 8.4.3, and resistance modification factor, R, as given in CSA A Section D.5.3, and noted in Tables 4, 5, 7, 8, 10, 11, 13 and 14 of this listing report, must be used for load combinations calculated in accordance with Division B, Part 4, Section of the 2015 NBCC, or Annex C of CSA A The nominal strength, N sa or V sa, in Tables 4, 7, and 10 of this listing report must be multiplied by s and R to determine the factored resistance, N sar or V sar. The bond strength must be adjusted by the permissible installation condition factors for dry, R d, and water-saturated, R ws, for the corresponding installation conditions as given in Tables 6, 9, 12 and 15. For anchors to be installed in seismic regions described in NBCC The factored resistance in shear, V sar, must be adjusted by α V,seis as given in tables 4, 7, and 10 for the corresponding anchor steel. The nominal bond strength k,cr must be adjusted by α N,seis a as given in Tables 6, 9, 12 and 15 for threaded rods.

8 ELC-4027 Most Widely Accepted and Trusted Page 7 of 15 CARBON STEEL STAINLESS STEEL THREADED ROD SPECIFICATION ASTM A193 2 Grade B7 ASTM A36 3 / F1554 4, Grade 36 TABLE 2 SPECIFICATIONS AND PHYSICAL PROPERTIES OF COMMON CARBON AND STAINLESS STEEL ROD MATERIALS 1 MINIMUM SPECIFIED ULTIMATE STRENGTH, f uta MINIMUM SPECIFIED YIELD STRENGTH 0.2 PERCENT OFFSET, f ya f uta/f ya ELONGATION, MIN. PERCENT 11 REDUCTION OF AREA, MIN. PERCENT MPa SPECIFICATION FOR NUTS 12 ASTM A194 / A563 Grade DH MPa ASTM A194 / A563 Grade A ASTM F Grade 55 MPa ASTM F Grade 105 MPa ASTM A449 5 (3/8" to1" dia.) ASTM A449 5 (1-1/4" dia.) ASTM F568M 6 Class 5.8 (equivalent to ISO 898-1) MPa MPa MPa ASTM A194 / A563 Grade DH A563 Grade DH DIN 934 (8-A2K) 13 ISO Class 5.8 MPa EN ISO 4032 Grade 6 ISO Class 8.8 MPa EN ISO 4032 Grade 8 ASTM F593 8 CW1 3 / 8 to 5 / 8 in. ASTM F593 8 CW2 3 / 4 to 1 1 / 4 in. ASTM A193/A193M 9 Grade B8/B8M2, Class 2B ISO A4-70 M10-M24 ISO A4-50 M27-M30 MPa MPa ASTM F594 Alloy Group 1, 2 or 3 MPa ASTM A194/A194M MPa EN ISO 4032 MPa EN ISO Adhesive must be used with continuously threaded carbon or stainless steel rod (all-thread) having thread characteristics complying with ANSI B1.1 UNC Coarse Thread Series. 2 Standard Specification for Alloy-Steel and Stainless steel Bolting Materials for High temperature of High Pressure service and Other Special Purpose Applications. 3 Standard Specification for Carbon Structural steel 4 Standard Specification for Anchor Bolts, Steel 36, 55 and 105-ksi Yield Strength 5 Standard Specification for Hex Cap Screws, Bolts and Studs, Heat Treated, 120/105/50 ksi (837/724/621 MPa) Minimum Tensile Strength, General Use. 6 Standard Specification for Carbon and Alloy Steel external Threaded Metric Fasteners 7 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, Screws and Studs 8 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs. 9 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High or High Pressure Service and Other Special Purpose Applications. 10 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, Screws and Studs 11 Based on 2-in. (50 ) gauge length except for ASTM A193, which is based on a gauge length of 4d. 12 Nuts and washers of other grades and style having specified proof load stress greater than the specified grade and style are also suitable. Nuts must have specified proof load stresses equal to or greater than the minimum tensile strength of the specified threaded rod. 13 Nuts for metric rods. TABLE 3 SPECIFICATIONS AND PHYSICAL PROPERTIES OF COMMON STEEL REINFORCING BARS 1 REINFORCING SPECIFICATION ASTM A615 1, A767 3, A996 4 Grade ASTM A706 2, A767 3 Grade UNITS MINIMUM SPECIFIED ULTIMATE STRENGTH, f uta MINIMUM SPECIFIED YIELD STRENGTH, f ya MPa MPa ASTM A615 1, Grade 40 MPa DIN BSt 500 MPa Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement. 2 Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement. 3 Standard specification for Zinc-Coated (Galvanized) steel Bars for Concrete Reinforcement. 4 Standard specification for Rail-Steel and Axle-steel Deformed bars for Concrete Reinforcement. 5 Reinforcing steel, reinforcing steel bars; dimensions and masses.

9 ELC-4027 Most Widely Accepted and Trusted Page 8 of 15 TABLE 4 STEEL DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT THREADED ROD 1 Threaded rod O.D. Threaded rod effective cross-sectional area ASTM A36/F1554, Grade 36 ASTM F1554 Grade 55 ASTM A193 Grade B7 ASTM F1554 Grade 105 ASTM A449 ASTM F568M Class 5.8 ASTM F593 CW Stainless ASTM A193/A193M Grade B8/B8M2, Class 2B Nominal strength as governed by steel strength (for a single anchor) d A se ² (inch²) 3 / (0.375) 50 (0.0775) 1 / (0.500) 92 (0.1419) Nominal Rod Diameter 5 / 8 3 / 4 7 / / (1.250) 15.9 (0.625) 146 (0.22) 19.1 (0.750) 216 (0.3345) 22.2 (0.875) 298 (0.4617) 25.4 (1.000) 391 (0.57) 625 (0.9691) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 2 R factor for shear 2 R Nominal strength as governed by steel strength (for a single anchor) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 2 R factor for shear 2 R Nominal strength as governed by steel strength (for a single anchor) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 2 R factor for shear 2 R Nominal strength as governed by steel strength (for a single anchor) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 2 R factor for shear 2 R Nominal strength as governed by steel strength (for a single anchor) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 3 R factor for shear 3 R Nominal strength as governed by steel N sa kn strength (for a single anchor) V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 3 R factor for shear 3 R Nominal strength as governed by steel strength (for a single anchor) N sa kn V sa kn Reduction factor for seismic shear α V,seis - 0. factor for tension 2 R factor for shear 2 R Values provided for coon rod material types based on specified strengths and calculated in accordance with CSA A Eq. D.2 and Eq. D.31, as applicable. Nuts and washers must comply with requirements for the rod. 2 The tabulated value of material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. Values correspond to ductile steel elements. 3 The tabulated value of material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. Values correspond to brittle steel elements.

10 ELC-4027 Most Widely Accepted and Trusted Page 9 of 15 TABLE 5 CONCRETE BREAKOUT DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT THREADED ROD IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 3 / 8 1 / 2 Nominal Rod Diameter 5 / 3 8 / 4 7 / / 4 Effectiveness factor for cracked Effectiveness factor for uncracked k c,cr k c,uncr SI (in-lb) SI (in-lb) Min. anchor spacing s min Min. edge distance Min. member thickness c min h min 48 (1 7 / 8) 41 (1 5 / 8) h ef + 30 (h ef / 4) 64 (2 1 / 2) 44 (1 3 / 4) 76 (3) 51 (2) 7 (17) 10 (24) 95 (3 3 / 4) Critical edge distance - splitting (for uncracked c ac - 2h ef ) 2 (2 3 / 8) factor for tension, R failure modes, Condition B 2 factor for shear, R failure modes, Condition B (4 1 / 4) 64 (2 1 / 2) 121 (4 3 / 4) 70 (2 3 / 4) For smaller edge distances see Table 1 of this report for reduced minimum edge distances h ef + 2d Additional setting information is described in Figure 3, installation instructions. 2 Condition A requires supplemental reinforcement, while Condition B applies where supplemental reinforcement is not provided or where pullout or pryout governs, as set forth in CSA A D.5. The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. 3 d 0 = hole diameter. 149 (5 7 / 8) 82 (3 1 / 4) TABLE 6 BOND STRENGTH DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT THREADED ROD IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 3 / 8 Nominal Rod Diameter 1 / 5 2 / 3 8 / 4 7 / / 4 Minimum embedment Maximum embedment range A 2,3 : range B 2,3 : range C 2,3 : h ef,min h ef,max (2 3 / 8) 191 (7 1 / 2) 70 (2 3 / 4) 254 (10) 79 (3 1 / 8) 318 (12 1 / 2) 89 (3 1 / 2) 381 (15) 89 (3 1 / 2) 445 (17 1 / 2) Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² (4) 508 (20) 127 (5) 635 (25) Dry MAC 4 cleaning CAC cleaning Anchor category Not applicable Strength reduction factor R d Anchor category Strength reduction factor R d Water-saturated MAC 4 cleaning CAC cleaning Anchor category Not applicable Strength reduction factor R ws Anchor category Strength reduction factor R ws Reduction factor for seismic tension α N,seis Bond strength values correspond to compressive strength f' c = 2,500 psi. For compressive strength, f' c between 2,500 psi and 8,000 psi, the tabulated characteristic bond strength may be increased by a factor of (f' c / 2500) range A: Maximum short term temperature = 176 F (80 C), maximum long term temperature = 122 F (50 C); range B: Maximum short term temperature = 248 F (120 C), maximum long term temperature = 161 F (72 C); range C: Maximum short term temperature = 320 F (1 C), maximum long term temperature = 212 F (100 C). Short term elevated temperatures are those that occur over brief intervals, e.g. as result of diurnal cycling. Long term temperatures are roughly constant over significant periods of time. 3 Characteristic bond strengths are for sustained loads including dead and live loads. For load combinations consisting of short-term loads only such as wind, bond strengths may be increased by 23 percent for temperature range C. 4 MAC cleaning is only permitted for installation in uncracked up to an embedment depth of 10 times anchor diameter.

11 ELC-4027 Most Widely Accepted and Trusted Page 10 of 15 TABLE 7 STEEL DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT REINFORCING BARS 1 Reinforcing bar O.D. Reinforcing bar effective crosssectional area ASTM A615, A767, A996 Grade Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear d A se ² (inch²) Nominal Bar Size No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No (0.375) 71 (0.110) 12.7 (0.500) 129 (0.200) 15.9 (0.625) 200 (0.310) 19.1 (0.750) 284 (0.440) 22.2 (0.875) 387 (0.0) 25.4 (1.000) 510 (0.790) 28.6 (1.125) 645 (1.000) 31.8 (1.250) 819 (1.270) N sa kn V sa kn α V,seis R factor for tension 3 R factor for shear ASTM A706 Grade Nominal strength as governed by steel strength (for a single anchor) Reduction for seismic shear N sa kn V sa kn α V,seis factor for tension R factor for shear R ASTM A615 Grade 40 Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear N sa kn V sa kn α V,seis R factor for tension 3 R factor for shear In accordance with ASTM A615, Grade 40 bars are furnished only in sizes No. 3 through No. 6 1 Values provided for coon bar material types based on specified strengths and calculated in accordance with CSA A Eq. D.2 and Eq. D.3. 2 The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. Values correspond to ductile steel elements 3 The tabulated value of material resistance factors c and s, and resistance modsification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. Values correspond to brittle steel elements. TABLE 8 CONCRETE BREAKOUT DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT REINFORCING BARS IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 Effectiveness factor for cracked Effectiveness factor for uncracked Min. anchor spacing Min. edge spacing Min. member thickness Critical edge spacing splitting (for uncracked ) k c,cr k c,uncr s min c min h min SI (in-lb) SI (in-lb) Nominal Bar Size No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No (1 7 / 8) 41 (1 5 / 8) h ef + 30 (h ef / 4) 64 (2 1 / 2) 44 (1 3 / 4) 76 (3) 51 (2) 95 (3 3 / 4) (2 3 / 8) 7 (17) 10 (24) c ac - 2h ef factor for tension, failure R modes, Condition B 2 factor for shear, failure R modes, Condition B (4 1 / 4) 64 (2 1 / 2) 121 (4 3 / 4) 70 (2 3 / 4) 133 (5 1 / 4) 76 (3) For smaller edge distances see Table 1 of this report for reduced minimum edge distances h ef + 2d Additional setting information is described in Figure 3, installation instructions. 2 Condition A requires supplemental reinforcement, while Condition B applies where supplemental reinforcement is not provided or where pullout or pryout governs, as set forth in CSA A D.5.3. The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. 3 d 0 = hole diameter. 149 (5 7 / 8) 82 (3 1 / 4)

12 ELC-4027 Most Widely Accepted and Trusted Page 11 of 15 TABLE 9 BOND STRENGTH DESIGN INFORMATION FOR U.S. CUSTOMARY UNIT REINFORCING BARS IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 DESIGN INFORMATION Minimum embedment Maximum embedment range A 2,3 : range B 2,3 : range C 2,3 : Nominal Bar Size Symbol Units No.3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No.10 h ef,min h ef,max (2 3 / 8) 191 (7 1 / 2) 70 (2 3 / 4) 254 (10) 79 (3 1 / 8) 318 (12 1 / 2) 89 (3 1 / 2) 381 (15) 89 (3 1 / 2) 445 (17 1 / 2) 102 (4) 508 (20) 114 (4 1 / 2) 572 (22 1 / 2) Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² (5) 635 (25) Dry MAC 4 cleaning Anchor category Not applicable Strength reduction factor R d CAC cleaning Anchor category Strength reduction factor R d Watersaturated MAC 4 cleaning Anchor category Not applicable Strength reduction factor R ws CAC cleaning Anchor category Strength reduction factor R ws Reduction factor for seismic tension α N,seis Bond strength values correspond to compressive strength f' c = 2,500 psi. For compressive strength f' c between 2,500 psi and 8,000 psi, tabulated characteristic bond strength may be increased by a factor of (f' c / 2,500) range A: Maximum short term temperature = 176 F (80 C), maximum long term temperature = 122 F (50 C); range B: Maximum short term temperature = 248 F (120 C), maximum long term temperature = 161 F (72 C); range C: Maximum short term temperature = 320 F (1 C), maximum long term temperature = 212 F (100 C). Short term elevated temperatures are those that occur over brief intervals, e.g. as result of diurnal cycling. Long term temperatures are roughly constant over significant periods of time. 3 Characteristic bond strengths are for sustained loads including dead and live loads. For load combinations consisting of short term loads only, such as wind and seismic, bond strengths may be increased by 23 percent for temperature range C. 4 MAC cleaning is only permitted for installation in uncracked up to an embedment depth of 10 times anchor diameter. Threaded rod O.D. Threaded rod effective crosssectional area ISO Class 5.8 ISO Class 8.8 ISO , A4 stainless steel 3 Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear TABLE 10 STEEL DESIGN INFORMATION FOR METRIC THREADED ROD 1 d A se ( inch) ² ( inch²) Nominal Rod Diameter () M10 M12 M16 M20 M24 M27 M30 10 (0.39) 58.0 (0.090) 12 (0.47) 84.3 (0.131) 16 (0.63) 157 (0.243) 20 (0.79) 245 (0.380) 24 (0.94) 353 (0.547) 27 (1.06) 459 (0.711) 30 (1.18) 561 (0.870) N sa kn V sa kn α V,seis R factor for tension 2 R factor for shear Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear N sa kn V sa kn α V,seis R factor for tension 2 R factor for shear Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear N sa kn V sa kn α V,seis - 0. factor for tension 2 R factor for shear 2 R Values provided for coon rod material types based on specified strengths and calculated in accordance with CSA A Eq. D.2 and Eq. D.3. Nuts and washers must comply with requirements for the rod. 2 The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. Values correspond to brittle steel elements 3 A4-70 Stainless steel (M8-M24); A4-50 Stainless steel (M27-M30)

13 ELC-4027 Most Widely Accepted and Trusted Page 12 of 15 DESIGN INFORMATION Effectiveness factor for cracked Effectiveness factor for uncracked Min. anchor spacing Min. edge distance Min. member thickness TABLE 11 CONCRETE BREAKOUT DESIGN INFORMATION FOR METRIC THREADED ROD IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 Symbol Units k c,cr k c,uncr s min c min h min SI (in-lb) SI (in-lb) ( inch) Nominal Rod Diameter () M10 M12 M16 M20 M24 M27 M30 50 (2) 40 (1 5 / 8). h ef + 30 (h ef / 4) (2 3 / 8) 45 (1 3 / 4) 75 (3) 50 (2) 7 (17) 10 (24) 95 (3 3 / 4) (2 3 / 8) Critical edge distance - splitting 2 cac - 2hef (for uncracked ) factor for tension, failure R modes, Condition B (4 1 / 2) 65 (2 1 / 2) 125 (5) 75 (3) For smaller edge distances see Table 1 of this report for reduced minimum edge distances h ef + 2d 0 3 factor for shear, failure modes, Condition B 2 R Additional setting information is described in Figure 3, installation instructions. 2 Condition A requires supplemental reinforcement, while Condition B applies where supplemental reinforcement is not provided or where pullout or pryout governs, as set forth in CSA A23.3 D.5.3. The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A are used. 3 d 0 = hole diameter. 140 (5 1 / 2) 80 (3 1 / 8) Minimum embedment Maximum embedment range A 2,3 : range B 2,3 : range C 2,3 : TABLE 12 BOND STRENGTH DESIGN INFORMATION FOR METRIC THREADED ROD IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 h ef,min h ef,max Nominal Rod Diameter M10 M12 M16 M20 M24 M27 M30 Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² (2.4) 200 (7.9) 70 (2.8) 240 (9.4) 80 (3.1) 320 (12.6) 90 (3.5) 400 (15.7) 96 (3.8) 480 (18.9) 108 (4.3) 540 (21.3) 120 (4.7) 0 (23.6) Dry MAC 4 cleaning CAC cleaning Anchor category Not applicable Strength reduction factor R d Anchor category Strength reduction factor R d Watersaturated MAC 4 cleaning CAC cleaning Anchor category Not applicable Strength reduction factor R ws Anchor category Strength reduction factor R ws Reduction factor for seismic tension α N,seis Bond strength values correspond to compressive strength f' c = 2,500 psi. For compressive strength, f' c between 2,500 psi and 8,000 psi, the tabulated characteristic bond strength may be increased by a factor of (f' c / 2500) See Section of this report. 2 range A: Maximum short term temperature = 176 F (80 C ), maximum long term temperature = 122 F (50 C); range B: Maximum short term temperature = 248 F (120 C), maximum long term temperature = 161 F (72 C); range C: Maximum short term temperature = 320 F (1 C), maximum long term temperature = 212 F (100 C). Short term elevated temperatures are those that occur over brief intervals, e.g. as result of diurnal cycling. Long term temperatures are roughly constant over significant periods of time. 3 Characteristic bond strengths are for sustained loads including dead and live loads. For load combinations consisting of short-term loads only such as wind, bond strengths may be increased by 23 percent for temperature range C. 4 MAC cleaning is only permitted for installation in uncracked up to an embedment depth of 10 times anchor diameter.

14 ELC-4027 Most Widely Accepted and Trusted Page 13 of 15 Reinforcing bar O.D. Reinforcing bar effective crosssectional area DIN 488 BSt 500 Nominal strength as governed by steel strength (for a single anchor) Reduction factor for seismic shear TABLE 13 STEEL DESIGN INFORMATION FOR METRIC REINFORCING BARS 1 d A se ² (inch²) Nominal Bar Size Ø 10 Ø 12 Ø 14 Ø 16 Ø 20 Ø 25 Ø 28 Ø (0.315) 78.5 (0.112) 12 (0.394) (0.175) 14 (0.472) (0.239) 16 (0.551) (0.312) 20 (0.630) (0.487) 25 (0.787) (0.761) 28 (1.102) (0.954) 32 (1.2) (1.247) N sa kn V sa kn α V,seis R factor for tension 2 R factor for shear 1 Values provided for coon bar material types based on specified strengths and calculated in accordance with CSA A Eq. D.2 and Eq. D.3. 2 The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A TABLE 14 CONCRETE BREAKOUT DESIGN INFORMATION METRIC REINFORCING BARS IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 Effectiveness factor for cracked Effectiveness factor for uncracked Min. anchor spacing Min. edge spacing Min. member thickness k c,cr k c,uncr s min c min h min SI (in-lb) SI (in-lb) ( inch) ( inch) Nominal Bar Size Ø 10 Ø 12 Ø 14 Ø 16 Ø 20 Ø 25 Ø 28 Ø (2) 40 (1 5 / 8) h ef + 30 (h ef / 4) (2 3 / 8) 45 (1 3 / 4) 70 (2 3 / 4) Critical edge spacing splitting 2 cac - 2hef (for uncracked ) factor for tension, failure R modes, Condition B 2 factor for shear, failure R modes, Condition B 2 50 (2) 75 (3) 50 (2) 7 (17) 10 (24) 95 (3 3 / 4) (2 3 / 8) 120 (4 5 / 8) 70 (2 3 / 4) 130 (5 1 / 4) 75 (3) For smaller edge distances see Table 1 of this report for reduced minimum edge distances h ef + 2d Additional setting information is described in Figure 3, installation instructions. 2 Condition A requires supplemental reinforcement, while Condition B applies where supplemental reinforcement is not provided or where pullout or pryout governs, as set forth in CSA A D.5.3. The tabulated value of the material resistance factors c and s, and resistance modification factor, R, applies when the load combinations of Division B, Part 4, Section of the 2015 NBCC or Annex C of CSA A d 0 = hole diameter. 150 (5 7 / 8) 85 (3 1 / 8)

15 ELC-4027 Most Widely Accepted and Trusted Page 14 of 15 DESIGN INFORMATION Minimum embedment Maximum embedment range A 2,3 : range B 2,3 : range C 2,3 : TABLE 15 BOND STRENGTH DESIGN INFORMATION METRIC REINFORCING BARS IN HOLES DRILLED WITH A HAMMER DRILL AND CARBIDE BIT 1 Nominal Bar Size Symbol Units Ø 10 Ø 12 Ø 14 Ø 16 Ø 20 Ø 25 Ø 28 Ø 32 h ef,min h ef,max ( inch) ( inch) Characteristic bond strength in uncracked k,uncr N/² (2.4) 200 (7.9) 70 (2.8) 240 (9.4) 75 (3.0) 280 (11.0) 80 (3.1) 320 (12.6) 90 (3.5) 400 (15.7) 100 (3.9) 500 (19.7) 112 (4.4) 5 (22.0) Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² Characteristic bond strength in uncracked k,uncr N/² Characteristic bond strength in cracked k,cr N/² (5.0) 640 (25.2) Dry MAC 4 cleaning Anchor category Not Applicable Strength reduction factor R d CAC cleaning Anchor category Strength reduction factor R d Water-saturated MAC 4 cleaning Anchor category Not Applicable Strength reduction factor R ws CAC cleaning Anchor category Strength reduction factor R ws Reduction factor for seismic tension α N,seis Bond strength values correspond to compressive strength f' c = 2,500 psi. For compressive strength f' c between 2,500 psi and 8,000 psi, tabulated characteristic bond strength may not be increased. See Section of this report. 2 range A: Maximum short term temperature = 176 F (80 C), maximum long term temperature = 122 F (50 C); range B: Maximum short term temperature = 248 F (120 C), maximum long term temperature = 161 F (72 C); range C: Maximum short term temperature = 320 F (1 C), maximum long term temperature = 212 F (100 C). Short term elevated temperatures are those that occur over brief intervals, e.g. as result of diurnal cycling. Long term temperatures are roughly constant over significant periods of time. 3 Characteristic bond strengths are for sustained loads including dead and live loads. For load combinations consisting of short term loads only, such as wind and seismic, bond strengths may be increased by 23 percent for temperature range C. 4 MAC cleaning is only permitted for installation in uncracked up to an embedment depth of 10 times anchor diameter.

16 ELC-4027 Most Widely Accepted and Trusted Page 15 of 15 Conditions of listing: 1. The listing report addresses only conformance with the standards and code sections noted above. 2. Approval of the product s use is the sole responsibility of the local code official. 3. The listing report applies only to the materials tested and as submitted for review by ICC-ES. 4. Anchor sizes, dimensions, minimum embedment depths and other installation parameters are as set forth in this listing report. 5. Anchors must be limited to use in cracked and uncracked normal-weight and lightweight having a specified compressive strength, f' c, of 2,500 psi (17.2 MPa) to 8,500 psi (58.6 MPa). 6. The values of f' c, used for calculation purposes must not exceed 55 MPa. 7. Limit states design values must be established in accordance with this listing report. 8. The use of fatigue or shock loading for these anchors under such conditions is beyond the scope of this listing report. 9. Anchors may be used to resist short-term loading due to wind or seismic forces in locations designed according to NBCC Where not otherwise prohibited in the code as referenced in CSA A , the DEWALT AC200+ adhesive anchor system is permitted for use with fire-resistance-rated construction provided that at least one of the following conditions is fulfilled: a. Anchors are used to resist wind or seismic forces only. b. Anchors that support a fire-resistance-rated envelope or a fire- resistance-rated membrane are protected by approved fire-resistance- rated materials, or have been evaluated for resistance to fire exposure in accordance with recognized standards. c. Anchors are used to support nonstructural elements. 11. Use of zinc-coated carbon steel anchors is limited to dry, interior locations. 12. Use of anchors made of stainless steel as specified in this report are permitted for exterior exposure and damp environments. 13. Steel anchoring materials in contact with preservative-treated wood and fire-retardant-treated wood must be of zinc-coated carbon steel or stainless steel. The minimum coating weights for zinc-coated steel must comply with ASTM A Installation of anchors in horizontal or upwardly inclined orientations to resist sustained tension loads shall be performed by personnel certified by an applicable certification program, and the certification shall include written and performance tests in accordance with the ACI/CRSI Adhesive Anchor Installer Certification program, or equivalent in accordance with CSA A D The installation shall be continuously inspected during installation by an inspector specially approved for that purpose. The special inspector shall furnish a report to the licensed design professional and building official that the work covered by the report has been performed and that the materials used and the installation procedures used conform with the approved contract documents and the MPII in accordance with CSA A D