Pre-installation checklist. 3. Project manager has read specifications, and specs to be on-site during work.
|
|
- Louise Ross
- 6 years ago
- Views:
Transcription
1 Pre-installation checklist 1. Contractor qualifications verified. 2. Project manager is Belden/CDT installer certified. 3. Project manager has read specifications, and specs to be on-site during work. 4. Project manager is trained and certified to use a Fluke Networks DTX tester. 5. Pre-registration of project with product manufacturers for warranty. 6. CAD drawings provided to or obtained by contractor. 7. As-built drawings required, keep notes on all changes. 8. Review fiber backbone installation requirements and lengths. Have RCDD call. 9. On-reel testing of fiber cables required. 10. Questions regarding specs or job scope. 11. Meet with project manager / foreman and installers and advise on District requirements / expectations and installation checklist. (i.e. Carefully follow Belden/CDT installation practices, station ID format & size, no visible or unprotected cable, staggered 7ft. service loops in closet or hallway, slack in cable where conduit meets raceway, no tie-wraps on cable, beware of distances to farthest locations, clear labeling of fiber cable, replace bolts on manhole covers, set cable type in tester correctly, cleanup debris).
2 1 Installation Checklist 1. Specifications on site. 2. Project manager has read specifications 3. Only BICSI-certified technicians and installers on job. 4. Specified materials to be used on job (10GX12 CMR, 10GX13 CMP). 5. Drawing being updated for as-built. 6. CPI racks and cable management delivered. 7. Racks placed 36 from rear of upright channels to walls, bolted to floor. 8. Ladder racks anchored to top of racks. 9. Ladder racks anchored to walls with correct brackets. 10. Verify UL labeling on racks and splice components. 11. Blank filler panel installed into patch panel side of middle rack(s). 12. Large CPI cable management brackets installed into racks. 13. Rack vertical rails bonded to communications ground bus bar. 14. Ladder rack sections bonded to each other by straps or UL splices. 15. Ladder rack bonded to communications ground bus bar. 16. Copper cable delivered (CMR / CMP) partial balance 17. Data & voice jacks delivered partial balance 18. Faceplates & other materials delivered partial balance 19. Patch panels placed into racks. 20. Copper cables placed (rough-in) partial balance 21. Service loops placed neatly above racks or in hallway.
3 2 22. All wall station jacks terminated. 23. Station cable sheath labeled. 24. Wall faceplates and inserts installed (straight, level). 25. Wall faceplates labeled. 26. Floorbox jacks terminated and faceplates installed. 27. Floorbox faceplates labeled. 28. Above-ceiling jacks terminated and correct ceiling faceplates installed. 29. Above-ceiling faceplates labeled. 30. Surface raceway faceplates installed. 31. Surface raceway faceplates labeled. 32. Surface raceway blank faceplates installed where necessary. 33. Furniture / table faceplates installed. 34. Furniture / table faceplates labeled. 35. Dust caps installed on all data jacks (some missing ). 36. All cables terminated at patch panels. 37. Cables neatly dressed behind racks and within Equipment Room. 38. Patch panel cable sheath labeled. 39. Station locations cleaned of debris. 40. Equipment Room cleaned of debris. 41. Communications / ladder rack cleaned of construction dust. 42. Fluke DTX to be used is within calibration period. 43. Fluke DTX has latest firmware installed. 44. Fluke DTX cable type set correctly from cable library.
4 3 45. All cables pass testing with Fluke DTX with no marginal pass. 46. All fire-stopping installed to DSA inspector satisfaction. 47. Firewall penetrations labeled and photographed. 48. Blue patch cords delivered, 12 x X patch panels (XX), Blue patch cords delivered, 36 x X patch panels (XX), Gray station cords delivered, 48 x X patch panels (XX) - 10%; Gray station cords delivered, 48 x X patch panels (XX) x 10%; Network equipment patched to panels and neatly dressed. 53. Fiber cable lengths carefully measured prior to ordering. 54. Fiber cable delivered. 55. OTDR to be used is within calibration period. 56. OTDR has latest firmware installed. 57. Splice housing mounted in?? room. 58. All fiber patch panels installed in racks. 59. Fiber cables placed, with Muletape installed alongside. 60. Service loops in utility bunkers (except for Plug & Play cable). 61. Fiber cable identified / labeled after installation. 62. Fiber splices and terminations within tolerances (0.15 db splice; 0.3dB term.) 63. No fiber cable splicing except as noted in specs. 64. Fiber tested with Fluke DTX and correct fiber adaptors. 65. Fiber tested with Fluke or Corning OTDR. 66. Bolts installed on all manhole covers. 67. Fluke DTX copper and fiber test results downloaded to PC.
5 4 68. Sample random station locations checked for proper termination. 69. Sample random re-tests done and verified against original. 70. Test results CD received (Fluke DTX copper & fiber, OTDR). 71. As-built drawing CD and 2 hardcopy sets received. May be on same CD as test results. 72. Belden/CDT warranty received. 73. Corning Cable Systems warranty received. For any questions / comments, contact: Mario Morales Sr. Electronic Systems Technician Cerritos College (562) ext Notes
COMMUNICATIONS CABLING SECTION COMMUNICATIONS CABLING PART 1 - GENERAL
13686.00 COMMUNICATIONS CABLING 271513-1 1.1 RELATED SECTIONS SECTION 27 1513 COMMUNICATIONS CABLING PART 1 - GENERAL A. Drawings and general provisions of the Contract, including General and Supplementary
More informationA. Drawings and general provisions of the Contract, including General Conditions and Division 1 Specification sections, apply to work of this Section.
SECTION 27 00 00 TELECOMMUNICATIONS CABLE PLANT 1. GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions and Division 1 Specification sections,
More informationA. Basket Cable Tray: A fabricated structure consisting of wire mesh bottom and side rails.
SECTION 27 11 00 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationA. Drawings and general provisions of the Contract, including General Conditions and Division 1 Specification sections, apply to work of this Section.
SECTION 270000 TELECOMMUNICATIONS CABLE PLANT 1. GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions and Division 1 Specification sections, apply
More information1 data PIC location (with 2 ports) typically asf for multiple staff members
1 Introduction 1.1 In the design of Telecommunications systems in Purdue facilities, the overall consideration should be to understand and treat telecom as a utility. It should be assumed that all new
More informationCommunications Page 1 of 9
Page 1 of 9 Last Update: April 23 rd, 2014 Introduction Design In the design of Telecommunications systems in Purdue facilities, the overall consideration should be to understand and treat telecom as a
More informationPHYSICAL FACILITIES Consultant s Handbook Division 27 COMMUNICATIONS 0000 COMMUNICATIONS
1 Introduction 1.1 In the design of Telecommunications systems in Purdue facilities, the overall consideration should be to understand and treat telecom as a utility. It should be assumed that all new
More information1. Telecommunications mounting elements. 2. Backboards. 3. Telecommunications equipment racks and cabinets. 4. Grounding.
ALLIANT ENERGY CENTER PAVILIONS Project No. 2013 027 SECTION 27 11 00 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationRequest for Proposal
Request for Proposal Dillon School District Three Telecommunications Cabling for Latta Middle School Contact: Robert McIntyre, Director of Technology (843) 752-7101 office phone (843)752-2081 office fax
More informationCOMMUNICATIONS EQUIPMENT ROOM FITTINGS
SECTION 271100 - COMMUNICATIONS EQUIPMENT ROOMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationUNIVERSITY OF ALABAMA AT BIRMINGHAM DEPARTMENT OF FACILITIES PLANNING. NAME: Communications Equipment Room ORIGINAL DATE:
UNIVERSITY OF ALABAMA AT BIRMINGHAM DEPARTMENT OF FACILITIES PLANNING FACILITIES STANDARD PURPOSE: 1. The general purpose of each Facilities Standard is to provide minimal criteria for construction materials
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 27 1000 - STRUCTURED CABLING PART 1 - GENERAL 1.1 RELATED DOCUMENT A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More information.2 The maximum length of horizontal cable shall not exceed 90 meters in any 360 degree direction.
1.0 GENERAL 1.1 DOCUMENTS.1 This section of the Specification forms part of the Contract Documents and is to be read, interpreted, and coordinated with all other parts. 1.2 SUMMARY.1 Section Includes:
More informationCity and County of San Francisco CONTRACT No A SFO - Data Center, Building 60 SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 27 05 36 CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 SCOPE OF WORK A. Cable Trays for Communications Cabling 1. Cable Trays 2. Cable Runways 3. Basket Tray B. Cable Tray Support
More informationA. Basket Cable Tray: A fabricated structure consisting of wire mesh bottom and side rails.
SECTION 16714 - COMMUNICATIONS EQUIPMENT ROOM FITTINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationTelecommunications Cabling System Technical Specification
1.0 INTRODUCTION Telecommunications Cabling System Technical Specification 1.1 PURPOSE The intent of this document is to provide a standard specification that will be used for all University of Northern
More information1. General Telecommunications Design Considerations
1. General Telecommunications Design Considerations 1.1. Entrance Point and Main Telecommunications Room Design 1.1.1. Conduit entrances typically consist of three 4 conduits. Conduit quantities are determined
More information.1 This Section includes equipment, materials, labour and services to provide telephone and data distribution systems including, but not limited to:
1.0 GENERAL 1.1 DOCUMENTS.1 This section of the Specification forms part of the Contract Documents and is to be read, interpreted, and coordinated with all other parts. 1.2 SUMMARY.1 Section Includes:
More informationOREGON UNIVERSITY SYSTEM STANDARD PUBLIC IMPROVEMENT CONTRACT BID FORM. FROM: Name of Contractor
OREGON UNIVERSITY SYSTEM STANDARD PUBLIC IMPROVEMENT CONTRACT BID FORM OUS CAMPUS: PROJECT: BID CLOSING: University of Oregon Chiles Hall 3 rd Floor Business Technology Center Improvements Project June
More informationSECTION PATHWAYS FOR COMMUNICATIONS SYSTEMS
(NOTE TO DESIGNER: These Specifications are basic minimum criteria to be met in preparing the final specifications for this section, which is the responsibility of the Designer.) PART 1 - GENERAL 1.1 SECTION
More informationSECTION COMMUNICATIONS EQUIPMENT ROOM FITTINGS
SECTION 271100 COMMUNICATIONS EQUIPMENT ROOM PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 00 and
More informationSECTION HORIZONTAL CABLING
PART 1 - GENERAL 1.1 SUMMARY SCOPE OF WORK SECTION 25160 HORIZONTAL CABLING 1. Horizontal cabling is the portion of the cabling system that extends from the work area to the Telecommunications Room or
More informationNYULMC AMBULATORY CARE CENTER FIT-OUT PHASE 1 Perkins & Will Architects PC 222 E 41st ST, NYC Project: Issued for GMP March 15, 2017
SECTION 27 05 26 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationThis product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update.
Kaf-Tech Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519 METAL CLAD CABLE - MC-PLUS Neutral
More informationAddendum 1.0. For Lagrange Library Specification 1.0. Technology Consultants Fort Wayne, Indiana
Addendum 1.0 For Lagrange Library Specification 1.0 Technology Consultants Fort Wayne, Indiana TECHNICAL SPECIFICATIONS FOR TELECOMMUNICATION DISTRIBUTION FACILITIES AND INSTALLATION PROCEDURES For Lagrange
More informationc. Army Reserve Design Process Submittal Requirements (DPSR) d. USARC G-2/6 IT Design Criteria Updates, 26 March 2013 ( ENCLOSURE 1)
CELRL-PM-R March ARCOS BULLETIN - SUBJECT: IT Design. REFERENCE: a. UFC --0, Army Reserve Facilities b. Army Reserve IT Manual, Change c. Army Reserve Design Process Submittal Requirements (DPSR) d. USARC
More informationC.I.C.S. WRIGHTWOOD SCHOOL CHICAGO CHARTER SCHOOL FOUNDATION TECHNOLOGY UPGRADES STRUCTURED CABLING SPECIFICATIONS SC0-01
T:\830 S Cliforni\CICS Wrightwoo Cmpus\DWGS\CAD\SCS\g_0.wg 0/3/08 5:3.05 y: jwyruh PART GENERAL.. PROJECT DESCRIPTION; A. PROVIDE AND INSTALL A COMPLETE STRUCTURED CABLING SYSTEM (SCS) FOR CICS WRIGHTWOOD
More informationSECTION TELECOMMUNICATIONS SYSTEMS
SECTION 16742 TELECOMMUNICATIONS SYSTEMS The following guidelines are provided for installation of telecommunications infrastructure for Dartmouth College supported by Computing, Network Services. These
More informationPolice/Emergency Service Center PSGP Grant #2007-GB-T CN
B. Concrete Slabs and Walls: Install sleeves for penetrations unless core-drilled holes or formed openings are used. Install sleeves during erection of slabs and walls. C. Use pipe sleeves unless penetration
More informationSECTION TELECOMMUNICATIONS DISTRIBUTION SYSTEM (TDS)
PART 1 - GENERAL 1.1 SCOPE A. Work Included SECTION 27 15 00 TELECOMMUNICATIONS DISTRIBUTION SYSTEM (TDS) 1. Furnishing and installation of a complete structured cabling system utilizing 100 OHM, 4-pair
More informationKaf-Tech Product Specification
Kaf-Tech Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519.13 METAL CLAD CABLE-LUMINARY CABLE
More informationSTRUCTURED CABLING. We re with you.
We re with you. Why We re Different We exist to serve and empower our Customers, Constituents, and Communities Inside comcables Founded in 1999, comcables is a premier manufacturer of end to end structured
More informationADDENDUM No. 2 Request for Proposals (RFP) 19RFP033 Structured Network Cabling
December 19, 2018 ADDENDUM No. 2 Request for Proposals (RFP) 19RFP033 Structured Network Cabling Item 1: General Clarifications Item 2: Questions and Answers Item 1: General Clarifications for 19RFP033
More informationUNLV Campus Wiring Specification September 15, 2016
UNLV Campus Wiring Specification September 15, 2016 1. Part I - General... 4 1.0. Purpose... 4 1.1. Contractor Qualifications... 4 1.2. Applicable Regulations... 5 A. Related Documents... 5 1.3. Submittal...
More informationTelecommunications Standards A. PERFORMANCE REQUIREMENTS
A. PERFORMANCE REQUIREMENTS 1. Scope of Work a. The work covered under this section shall include furnishing and installing a complete telecommunications system for the distribution and/or networked data
More informationSECTION COMMUNICATIONS OPTICAL FIBER OSP CABLING
SECTION 27 13 24 COMMUNICATIONS OPTICAL FIBER OSP CABLING PART 1 GENERAL 1.01 DESCRIPTION A. The work covered by this section of the Specifications includes all labor necessary to perform and complete
More informationRFB for Fiber Optic Cabling Attachment A Project Scope October 6, 2016
RFB for Fiber Optic Cabling Attachment A Project Scope October 6, 2016 1.0 Project Description 1.1 General 1.1.1 Drawings and general provisions of Contract, including General and Supplementary Conditions,
More informationDesign Guidelines for Facilities Construction:
Western Michigan University Office of Information Technology & Campus Planning, Design & Construction Design Guidelines for Facilities Construction: DESIGN GUIDELINE DG17-1 Outside / Inter-building Systems
More informationThis product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update.
AFC Cable Systems, Inc. Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519.13 METAL CLAD CABLE-MC
More informationDENVER PUBLIC SCHOOLS STRUCTURED CABLING DESIGN SPECIFICATIONS REVISED
DENVER PUBLIC SCHOOLS STRUCTURED CABLING DESIGN SPECIFICATIONS REVISED 07 09 10 1 1.1 INTRODUCTION 8 1.2 STRUCTURED COMMUNICATIONS CABLE SYSTEM GENERAL SPECIFICATIONS 8 1.2.1 STRUCTURED SYSTEMS DEFINITIONS
More informationFACILITIES BUILDING STANDARDS
FACILITIES BUILDING STANDARDS Section 25 0000 Integrated Automation Revised date: 09/18/18 PART 1 - GENERAL 1.1 SUMMARY A. Section includes the general requirements for the Integrated Automation systems.
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 260526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract apply to this Section. 1.2 SUMMARY A. This Section
More informationIssue for Bid January 25, 2010 SECTION A - COMMUNICATIONS COPPER HORIZONTAL CABLING
SECTION 27 15 13A - COMMUNICATIONS COPPER HORIZONTAL CABLING SECTION 27 15 13A - COMMUNICATIONS COPPER HORIZONTAL CABLING PART 1 GENERAL 1.1 DESCRIPTION A. Provide a complete Category 6 unshielded twisted
More informationStandards and Procedures Security Room Construction/Renovations At University of North Carolina Wilmington
Standards and Procedures Security Room Construction/Renovations At University of North Carolina Wilmington Rev 062017 Provided by UNCW Physical Security and Access OVERVIEW... 3 CABLE INSTALLATION... 3
More informationFontana Unified School District DATA SPECIFICATION E-Rate Specifications Section COMMUNICATION CONTRACTOR GENERAL CONDITIONS - At the
Part 1 COMMUNICATION CONTRACTOR GENERAL CONDITIONS - At the completion of the work, all systems shall be fully tested and operating in accordance with the intent of the drawings and specifications. To
More informationHASTINGS AREA SCHOOL SYSTEMS HASTINGS, MICHIGAN
Low Voltage Cabling Hastings High School CTE Program Technology Request for Bid Proposal HASTINGS AREA SCHOOL SYSTEMS HASTINGS, MICHIGAN 00 1001-1 SECTION 00 1005 TABLE OF CONTENTS SECTION TITLE BIDDING
More informationFLORIDA ARMY NATIONAL GUARD, CBJTC CACTF FIBER OPTIC CABLE INSTALLATION, PN SCOPE OF WORK, 28 MARCH 2012
1. General. 1.1 The project will require the provisioning and installation of conduits, hand holes, pull boxes and fiber optic cable extending several miles from a point of beginning to the Combined Arms
More informationTABLE OF CONTENTS DIVISION 27 - COMMUNICATIONS
TABLE OF CONTENTS DIVISION 27 - COMMUNICATIONS 27 00 00 COMMUNICATIONS... 2 27 00 01 GENERAL... 2 27 00 02 REFERENCES, REGULATORY REQUIREMENTS... 2 27 00 03 REFERENCES, RELATED SECTIONS of the SPECIFICATIONS...
More informationUMass Amherst Information Technology. Design and Construction Guidelines
UMass Amherst Information Technology Design and Construction Guidelines December 2018 2.13 INFORMATION TECHNOLOGY AND COMMUNICATIONS 2.13.1. General A. UMass IT/ Cable Engineering Services (CES) is here
More informationPHYSICAL FACILITIES Consultant s Handbook Specifications Division 27 Communication 0528 Pathways. Page 1 of 6
1 General 1.1 Scope of work 1.1.1 The Contractor is held responsible to be familiar with the provisions contained herein and with other Sections of this Specification as applicable to the completion of
More informationBuilding Design Standards December 2009 SECTION COMMUNICATIONS HISTORY DRAWINGS
SECTION 27 00 00 COMMUNICATIONS HISTORY The University Technology Services (UTS) Building Design Specification is a collection of requirements which architects and engineering consultants must adhere to
More informationEssex County College - West Essex Campus Addition And Renovations dlb # / 11-14
SECTION 270526 - GROUNDING AND BONDING FOR COMMUNICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationMaterial will comply with those standards as established by UL or NEMA and shall be commercial grade. All materials will be new and free from defects.
APPENDIX A: OSP INSTALLATION SPECIFICATIONS Material Requirements Material will comply with those standards as established by UL or NEMA and shall be commercial grade. All materials will be new and free
More informationPortland State University OIT Networking & Telecommunications Services
Portland State University OIT Networking & Telecommunications Services TELECOMMUNICATIONS CABLING/WIRING INSTALLATION & RELATED FACILITIES STANDARDS 2009-2011 Introduction The Office of Information Technology/
More informationOPS WIFI UPGRADE REQUEST FOR PROPOSAL: ADDENDUM - 1
OPS WIFI UPGRADE RFP ADDENDUM 1 1 OPS WIFI UPGRADE REQUEST FOR PROPOSAL: ADDENDUM - 1 The following information is being provided to promote as equal, fair, and competitive bidding process as possible
More informationSECTION INSIDE PLANT CABLE AND EQUIPMENT
PART 1 GENERAL SECTION 271000 UNLESS NOTED OTHERWISE, "CONTRACTOR" REFERS TO THE TELECOMMUNICATION CONTRACTOR. 1.01 SCOPE A. This section describes the products and execution requirements related to furnishing
More informationThe following sections are included in Division 27: Section : Underground Ducts and Raceways for Communication SysteMS 283
P a r t IV: De s i g n St a n d a r d s 279 Division 27: Communications Ge n e ra l Professionals shall verify that all applicable portions of these standards are incorporated into the final construction
More informationPATHWAYS MAKE IT POSSIBLE MDU MULTIPLE DWELLING UNIT
PATHWAYS MAKE IT POSSIBLE MDU MULTIPLE DWELLING UNIT Why install fiber directly to individual living units? 25% of all households are Multiple Dwelling Unit s (MDU s) and those owners & renters are the
More informationGUIDELINES. SPECIFICATION COMMUNICATIONS CABINETS AND EQUIPMENT ROOMS (Rev TAB)
PART 1 GENERAL 1.01 SUMMARY SPECIFICATION 271100 COMMUNICATIONS CABINETS AND EQUIPMENT ROOMS (Rev 06-25-2015- TAB) A. This section includes the specifications for constructing and building out of Telecommunications
More informationSECTION GROUNDING AND BONDING
SECTION 16060 GROUNDING AND BONDING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationLSA-PLUS Series 2. Connection and Disconnection Modules and Accessories. 1 st Edition
LSA-PLUS Series 2 Connection and Disconnection Modules and Accessories 1 st Edition LSA-PLUS Series 2 Connection and Disconnection Modules and Accessories A technically and commercially superior quick
More informationSECTION CONVECTORS
SECTION 23 82 33 PART 1 - GENERAL 1.1 DESCRIPTION SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph
More informationAlamo Colleges. Telecommunications Infrastructure Standards. For. New Facility Construction or Renovations. Version
For New Facility Construction or Renovations Version 2010.8.5 Prepared By: COMBS Consulting Group I.T. design & consulting 11550 IH-10 West, Suite 270 San Antonio, Texas 78230 Voice: 210-698-7887 Fax:
More informationDTW Works Master Specification Version 2006 Issued 2006/08/01 Section Data System Page 1 of 7
Issued 2006/08/01 Section 16743 Data System Page 1 of 7 PART 1 GENERAL 1.1 SYSTEM DESCRIPTION.1 Data system includes data outlets and wiring for office and school applications..2 Data system equipment
More informationRESEARCH AND TECHNOLOGY BUILDING RENOVATION MAY 18, 2009 SECTION COMMUNICATIONS
SECTION 27 00 00 PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following items for wiring systems used as signal pathways for voice and highspeed data transmission: 1. Communication outlets.
More informationE0.3. Telco. Specifications No Scale 12/3/2014 ADDENDUM #4. Table 1.1
A. General A. - The PSU Structured Cabling System includes: A.. - vertical and horizontal copper and fiber optic wiring A.. - the associated termination hardware on both ends (e.g. jacks, patch panels)
More informationA. Section includes busway and fittings including plug-in units.
SECTION 26 25 00 ENCLOSED BUS ASSEMBLIES PART 1 - GENERAL 1.1 SUMMARY A. Section includes busway and fittings including plug-in units. 1.2 REFERENCES A. Institute of Electrical and Electronics Engineers:
More informationc. Army Reserve Design Process Submittal Requirements (DPSR) d. USARC G-2/6 IT Design Criteria Updates, 17 October 2013 ( ENCLOSURE 1)
CELRL-PM-R October ARCOS BULLETIN - SUBJECT: IT Design Criteria Updates. REFERENCE: a. UFC --0, Army Reserve Facilities b. Army Reserve IT Manual, Change c. Army Reserve Design Process Submittal Requirements
More informationCypress-Fairbanks Independent School District
Cypress-Fairbanks Independent School District Bid Information Contact Information Ship to Information Bid Owner Paula S Ursery - Bid Coordinator Address 12510 Windfern Rd. Address CFISD Distribution Center
More informationOhio University Architecture, Design and Construction Standards
ALL ITEMS TO BE REVIEWED AND APPROVED BY PROJECT MANAGER AND OFFICE OF INFORMATION TECHNOLOGY (OIT) TELEPHONE AND NETWORK CLOSETS DEFINITIONS Backbone cable This is the primary cabling that provides data
More informationSECTION GROUNDING AND BONDING FOR ELECTRONIC SAFETY AND SECURITY
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 28 05 26 GROUNDING AND BONDING FOR ELECTRONIC SAFETY AND SECURITY SPEC WRITER NOTE: Delete // // if not applicable to project. Also delete any other item or paragraph
More informationRio Rancho Public Schools- Information Technology Services Network Infrastructure Cabling Requirements and Technical Specifications
Rio Rancho Public Schools- Information Technology Services Network Infrastructure Cabling Requirements and Technical Specifications CONTRACTOR REQUIREMENTS AND PROJECT PROCEDURES A: Electrical Codes: All
More informationVERTICALLY MOUNTED S210 BLOCKS (page 7.7) S210 TOWER SYSTEM (pages ) Mounting Options Wall 89D Bracket Wall 19 inch Rack 23 or 35 inch Frame
PRODUCTS CONNECTION SYSTEM (pages 7.2 7.7) VERTICALLY MOUNTED BLOCKS (page 7.7) TOWER SYSTEM (pages 7.4 7.5) FIELD TERMINATED 19 INCH PANELS (pages 7.6 7.7) XLBET FRAMES (pages 8.8 8.9) Racks Product Stard
More informationEnhanced Fiber Backbone Cabling System Specifications
Request for Proposals Enhanced Fiber Backbone Cabling System Specifications Date: December 14, 2017 Table of Contents 1. BACKGROUND... 4 2. REQUIREMENTS... 5 2.1. Examination of Site and Documents... 5
More informationApprenticeship Curriculum Standard. Levels 1 & 2
Apprenticeship Curriculum Standard Network Cabling Specialist Levels 1 & 2 631A 2001 Hours Disclaimer: It is agreed that Training Delivery Agents (TDAs) may need to make slight adjustments (with cause)
More informationPATHWAYS FOR COMMUNICATIONS SYSTEMS
270528 PATHWAYS FOR PART 1 GENERAL 1.1 WORK INCLUDED A. Provide all labor, materials, and equipment for the complete installation of work called for in the Contract Documents. 1.2 SCOPE OF WORK A. This
More informationSECTION Manufactured Metal Casework FLEXIBLE LABORATORY FURNITURE SYSTEM (OPTIMA) USA VERSION
SECTION 12 31 00.4 Manufactured Metal Casework FLEXIBLE LABORATORY FURNITURE SYSTEM (OPTIMA) USA VERSION PART 1 GENERAL Summary: This Specification identifies the minimum material and construction standards
More informationRSU 14 - WINDHAM RAYMOND SCHOOL DISTRICT OFFICE OF THE ASSISTANT SUPERINTENDENT
RSU 14 - WINDHAM RAYMOND SCHOOL DISTRICT OFFICE OF THE ASSISTANT SUPERINTENDENT 228 Windham Center Road, Windham, ME 04062 Telephone (207) 892-1800 FAX (207) 892-1805 INSTRUCTIONS, SPECIFICATIONS, AND
More informationRepackaging the Router
APPENDIXA Revised: March 16, 29, Introduction This appendix describes two separate but related router repackaging tasks: How to remove the router from the equipment rack and repackage the router for shipment
More informationThe University of Texas at Austin September 30, 2011
SECTION 27 05 26 GROUNDING AND BONDING FOR COMMUNICATIONS PART 1 - GENERAL 1.1 SUMMARY A. This section governs the products and execution requirements relating to furnishing and installing grounding and
More informationPERRIS ELEMENTARY SCHOOL DISTRICT GOOD HOPE ES AND RAILWAY STEM PROJECTOR UPGRADE SCOPE OF WORK
PERRIS ELEMENTARY SCHOOL DISTRICT GOOD HOPE ES AND RAILWAY STEM PROJECTOR UPGRADE SCOPE OF WORK 1. Summary: a. This project outlines the requirements for the installation of short throw projectors in the
More informationGUIDELINES. SPECIFICATION COMMUNICATIONS CABINETS AND EQUIPMENT ROOMS (Rev SJS)
PART 1 GENERAL 1.01 SUMMARY SPECIFICATION 271100 COMMUNICATIONS CABINETS AND EQUIPMENT ROOMS (Rev 08-26-2014- SJS) A. This section includes the specifications for constructing and building out of Telecommunications
More informationTroubleshooting Guide 9702 Series
Troubleshooting Guide 9702 Series Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com 1305-AUTO
More informationUNIVERSITY OF MISSOURI Electrical Manholes and Handholes 2016 Q1
GENERAL: The scope of this document is to provide instruction for the design and installation of medium voltage concrete electric manholes and handholes. DESIGN GUIDELINES: 1. Design for Manhole 1.1. The
More informationWarranties. What You Need To Know To Ensure Performance For Your Telecommunications Cabling System
Warranties What You Need To Know To Ensure Performance For Your Telecommunications Cabling System Reasons for Warranty Research Construction Issues Varying Manufacturer positions. Different Warranty Parameters
More informationBASIC TELECOMMUNICATION REQUIREMENTS January Communications
SECTION 27 05 00 BASIC TELECOMMUNICATION REQUIREMENTS PART 1 - GENERAL 1.1 SUMMARY A. Contractor shall include in the Bid all labor, materials, tools, plant, transportation, storage costs, training, equipment,
More informationTelecommunications Design Guidelines University of Alberta Cabling Standards (version 2.1)
February 7, 2008 Telecommunications Design Guidelines University of Alberta Cabling Standards (version 2.1) Introduction: For all planned building projects on the U of A campus, Facilities Management,
More informationSECTION COMMON WORK RESULTS FOR COMMUNICATIONS
SECTION 270500 - COMMON WORK RESULTS FOR COMMUNICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationTelecommunication Spaces
Telecommunication Spaces October 19, 2016 Page 1 Revision History Telecommunication Spaces Standard Effective Date Email Version Contact Phone OIT-TS strevena@csustan.edu 1.0 Stan Trevena 209.667.3137
More informationERK Series. features: options: specifications: enclosure. what great systems are built on.
enclosure The ERK Series 19 welded stand-alone / gangable enclosures. Advanced manufacturing techniques provide highest quality and lowest price. features: specifications: Fully welded construction 2,500
More informationREQUEST FOR PROPOSAL
HILLSBORO SCHOOL DISTRICT Hillsboro, Oregon REQUEST FOR PROPOSAL CABLING AND INFRASTRUCTURE Cabling and Infrastructure Implementation March 25, 2016 Division 27 Specifications This document provides the
More informationSECTION TELECOMMUNICATIONS GENERAL REQUIREMENTS
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Scope of Work B. Other Affected Trades C. Codes and Standards D. General Requirements and Conditions E. Telecommunication Contractor Qualifications F. Qualifications
More informationUNIVERSITY OF CHICAGO
UNIVERSITY OF CHICAGO Information Technology Services - ITS TELECOMMUNICATIONS STRUCTURED CABLING GUIDELINES AND SPECIFICATIONS INFRASTRUCTURE SERVICES May 2015 1 Contents 1 Introduction... 4 2.0 Planning
More informationSECTION GENERAL COMMUNICATIONS
SECTION 16700 GENERAL PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Not limited to: 1. Telecommunications Room/Equipment Room/Entrance Facility Section 16702. 2. Interior Communication Pathways - Section
More informationSECTION GROUNDING AND BONDING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 25 05 26 GROUNDING AND BONDING A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSUGGESTED SPECIFICATION for Low Voltage (600V) Generator Paralleling Switchboard
SUGGESTED SPECIFICATION for Low Voltage (600V) Generator Paralleling Switchboard PART 1 GENERAL 1.1 Scope A. The intent of this specification is to provide power control for the parallel operation of generator
More informationSAN ANTONIO technology & security AUSTIN SAN ANTONIO technology & security AUSTIN 7 7 GENERAL NOTES:. THE EXISTING CONDITIONS AS SHOWN ARE APPROXIMATELY CORRECT. NOT ALL EXISTING CONDITIONS ARE SHOWN.
More informationINTER-BUILDING CONDUIT & MANHOLE SYSTEM. Table of Contents PART 1 GENERAL 1 A. RELATED DOCUMENTS 1 B. SCOPE OF WORK 1 PART 2 PRODUCTS 6
UNIVERSITY CONTACT: Network Services (302) 831-3722 INTER-BUILDING CONDUIT & MANHOLE SYSTEM Table of Contents PART 1 GENERAL 1 A. RELATED DOCUMENTS 1 B. SCOPE OF WORK 1 PART 2 PRODUCTS 6 A. MATERIALS AND
More informationMINIMUM REQUIREMENTS FOR STRUCTURED CABLING
Last Reviewed 1/6/2017 MINIMUM REQUIREMENTS FOR STRUCTURED CABLING WEST VIRGINIA UNIVERSITY INFORMATION TECHNOLOGY SERVICES Telecommunications and Network Operations 1. GENERAL... 4 1.1 SUMMARY... 4 1.2
More informationInstaPATCH Plus Fiber System
Fiber System Trunk Cables Equipment and Cross-Connect Cords Ruggedized Fanout Cables Modular and High- Density Shelves The SYSTIMAX System features a high-density, factory terminated, factory tested, modular
More information