200 / 300 SERIES PANELS COLD STORAGE

Transcription

1 CS-DS /300 DISCLAIMER CS-CD /300 KINGSPAN CEILING DESIGN POLICY AND PROCEDURES CS-CD /300 KINGSPAN CEILING DESIGN POLICY AND PROCEDURES CONTINUED CI-PP PANEL PROFILES 200 SERIES CI-PP PANEL PROFILES 300 SERIES CS-PJ / SERIES EXPANDED PANEL JOINT CS-PJ / SERIES ENGAGED PANEL JOINT CS-PJ / SERIES EXPANDED PANEL JOINT CS-PJ / SERIES ENGAGED PANEL JOINT CS-PJ /300 INTERMEDIATE SUPPORT CS-PJ /300 LINER PANEL TO CONCRETE WITH SUPPORT CS-PJ /300 LINER PANEL TO CONCRETE CS-BS /300 BASE DETAIL - INSULATED SLAB W/ HEAVY GAUGE ANGLE CS-BS /300 BASE DETAIL - INSULATED SLAB W/ LIGHT GAUGE ANGLE CS-BS /300 BASE DETAIL - INSULATED SLAB W/ CHANNEL CS-BS /300 BASE DETAIL - PARTITION W/ FLOOR INSULATION CS-BS /300 BASE DETAIL - INSULATED/NON-INSULATED CS-BS /300 BASE DETAIL - PART. W/ CURBS INSULATED CS-BS /300 BASE DETAIL - PART. NON-INSULATED CS-BS /300 BASE DETAIL - LINER PANEL CS-BS /300 BASE DETAIL - PART. W/ CURBS NON-INSULATED CS-BS /300 BASE DETAIL - PART. W/ CURBS (ALTERNATE) CS-BS /300 PARTITION BASE ON TOP OF CURB CS-BS /300 BASE DETAIL W/ CURBS (ALTERNATE) CS-BS /300 PARTITION BASE ON TOP OF CURB CS-BS /300 BASE DETAIL W/ FACE INSULATED SLAB INDEX SHEET

2 CS-OC /300 OUTSIDE CORNER - FLUSH TRIM CS-OC /300 OUTSIDE CORNER - PROFILED TRIM CS-OC /300 OUTSIDE CORNER AT PARTITION CS-OC /300 OUTSIDE CORNER LINER PANEL AT CONC WALL CS-IC /300 INSIDE CORNER - FLUSH TRIM CS-IC /300 PARTITION TO EXTERIOR WALL CS-IC /300 PARTITION WALL INSIDE CORNER TO EXTERIOR WALL CS-FO /300 HEADER CONDITION CS-FO /300 JAMB CONDITION CS-ST /300 STACK JOINT CS-RK /300 RAKE CS-RK /300 RAKE W/ MEMBRANE ROOF CS-EV /300 LOW EAVE CS-CE /300 INTERIOR WALL TO CEILING CS-CE /300 INTERIOR WALL TO CEILING - 'T' SECTION CS-CE /300 CEILING CHANNEL CS-CE /300 CEILING TEE CS-CE /300 SUPPLEMENTAL CEILING CLIP CS-CE /300 CEILING TEE ASSEMBLY CS-CE /300 CEILING CHANNEL ASSEMBLY CS-CE /300 CEILING TO WALL - LONGITUDINAL CS-CE /300 CEILING TO WALL - TRANSVERSE CS-CE /300 PARTITION TO ROOF CS-CE /300 PARTITION TO ROOF WITH BLOCKING CS-CC /300 ALTERNATE CEILING CLIP CS-CC /300 ALTERNATE CEILING CLIP AT BUTT JOINT CS-CC /300 ALTERNATE CEILING CLIP INTERMEDIATE CS-BP /300 SEISMIC BRACE PLATE CS-TL /300 TRIM END LAP CS-TL /300 TRIM LAP WITH HEM CS-TL /300 TRIM END LAP WITH LAP STRIP CS-TL /300 TRIM LAP AT FRAMED OPENING INDEX SHEET

3 DISCLAIMERS: THESE DETAILS ARE PROVIDED AS A GUIDELINE FOR PROPER PANEL AND ASSOCIATED COMPONENT INSTALLATION, AND ARE BASED ON INDUSTRY ACCEPTED PRACTICES. REFRIGERATION EQUIPMENT IN COMBINATION WITH THE TEMPERATURE DIFFERENTIAL BETWEEN BUILDING EXTERIOR AND INTERIOR CAN CREATE NEGATIVE AIR PRESSURE WITHIN THE BUILDING (WARM AIR FROM OUTSIDE THE BUILDING IS DRAWN INTO THE BUILDING THROUGH AIR LEAKS IN THE BUILDING ENVELOPE). AS A RESULT, VAPOR SEALS ARE OF PRIMARY CONCERN TO PROPER COLD STORAGE PERFORMANCE. IN GENERAL, COLD STORAGE FACILITIES REQUIRE THE PRIMARY VAPOR BARRIER TO BE ON THE EXTERIOR (I.E. ), RATHER THAN INTERIOR SIDE OF THE PANEL. PROJECTS LOCATED IN AREAS SUBJECT TO EXTREME COLD AND/OR HIGH SNOW LOADS MAY REQUIRE MODIFICATIONS TO THESE DETAILS - CONTACT KINGSPAN TECHNICAL SERVICES FOR SPECIFIC PROJECT RECOMMENDATIONS. ALL STRUCTURAL SUPPORTS ARE NOT BY KINGSPAN AND ARE SHOWN FOR CLARIFICATION AND ILLUSTRATION PURPOSES ONLY. CONTACT KINGSPAN TECHNICAL SERVICES FOR MAXIMUM ALLOWABLE PANEL SPANS AND FASTENING PATTERNS. ALL SEALANTS TO BE COMPATIBLE WITH VAPOR BARRIERS AS SHOWN ADDITIONAL NOTES: 1. FOLLOW RECOMMENDED TEMPERATURE PULL-DOWN FOR REFRIGERATED ROOMS, ESPECIALLY FREEZERS. 2. PROVIDED HEATED FRAME, THRESHOLD FOR DOORS IN FREEZERS. 3. FREEZERS BELOW 26 F SHOULD HAVE HEATED SYSTEMS UNDER FLOOR INSULATION. COLD STORAGE DISCLAIMER

4 KINGSPAN CEILING SYSTEM DESIGN POLICY AND PROCEDURES TO ENSURE PUBLIC SAFETY, APPLICATION ENGINEERING IS REQUIRED FOR A SUSPENDED CEILING SYSTEM CONSTRUCTED WITH KINGSPAN INSULATED PANELS. EACH OF THE STEPS SHOWN BELOW MUST BE FOLLOWED, WITHOUT EXCEPTION. 1. THE PROJECT ENGINEER (RETAINED BY OWNER OR CONTRACTOR) MUST IDENTIFY THE DESIGN LOADS (UNIFORMLY DISTRIBUTED AND/OR CONCENTRATED) TO WHICH THE CEILING WILL BE DESIGNED. 2. THE PROJECT ENGINEER (RETAINED BY OWNER OR CONTRACTOR) IS RESPONSIBLE FOR DESIGNING THE ATTACHMENT OF THE THREADED RODS FROM THE CEILING SYSTEM TO THE ROOF STRUCTURE ABOVE, INCLUDING ANY MISCELLANEOUS SUPPORT MEMBERS REQUIRED. 3. THE PROJECT ENGINEER (RETAINED BY OWNER OR CONTRACTOR) MUST VERIFY AND APPROVE THAT THE ROOF STRUCTURE IS CAPABLE OF SUPPORTING THE ADDITIONAL LOADS IMPOSED BY THE CEILING SYSTEM. 4. THE PROJECT ENGINEER (RETAINED BY OWNER OR CONTRACTOR) SHALL REVIEW CEILING SYSTEM DRAWINGS FOR COMPLIANCE WITH ENGINEERING CRITERIA. 5. THE PROJECT OWNER / OWNER'S REP SHALL SPECIFY PANEL THICKNESS BASED ON R-VALUES. 6. KINGSPAN ENGINEERING SHALL VERIFY SPECIFIED PANEL THICKNESS IS ADEQUATE FOR REQUIRED SPAN AND LOADING CONDITIONS. 7. KINGSPAN ENGINEERING SHALL DETERMINE THE SPACING OF THE THREADED RODS USED WITH KINGSPAN ALUMINUM T EXTRUSIONS OR CEILING CHANNELS. KINGSPAN ENGINEERING WILL ALSO DETERMINE THE APPROPRIATE CEILING SUPPORT DETAILS, EXCLUDING THE ATTACHMENT OF THREADED RODS TO THE ROOF. 8. KINGSPAN ENGINEERING MUST REVIEW CEILING SYSTEM DRAWINGS BEFORE DESIGN IS FINALIZED. 9. IF THE DESIGN LOADS ARE NOT PROVIDED TO KINGSPAN ENGINEERING, THE DEFAULT DESIGN OF THE CEILING SYSTEM PROVIDED BY KINGSPAN WILL BE BASED ON THE CONCEPT OF LIGHT DUTY WITH LIMITED ACCESS. THIS IS EQUIVALENT TO A CONCENTRATED LIVE LOAD OF 300 LBS (ONE PERSON WITH TOOLS EXCLUDING HEAVY TOOL BOXES, GAS CYLINDERS, PIPE VISES, ETC.) OVER A 30"X30" AREA PLUS DEAD LOAD (DEFINED AS THE WEIGHT OF CEILING PANELS AND SUPPORTING ACCESSORIES PROVIDED BY KINGSPAN). A// OTHER REQUIREMENTS OF ITEMS #2, 3 AND 4 ARE STILL IN EFFECT. 10. OPENINGS AND OTHER PENETRATIONS IN CEILING PANELS INCLUDING BUT NOT LIMITED TO ACCESS DOORS, DUCTWORK, LARGE PIPING ETC. MAY REQUIRE ADDITIONAL STRUCTURAL SUPPORT FRAMING. ATTACHMENT METHOD OF LIGHTING FIXTURES ETC. AFFIXED TO THE CEILING MUST BE PRE-APPROVED BY KINGSPAN ENGINEERING. 11. THE CEILING, BOTH DURING AND AFTER INSTALLATION, MUST NOT BE USED AS A WORKING PLATFORM. 12. STORAGE OF ITEMS OR MATERIALS OF ANY KIND (I.E. DEAD LOADS) ON TOP OF CEILING DURING AND AFTER INSTALLATION IS STRICTLY PROHIBITED. CEILING SYSTEM DESIGN POLICY AND PROCEDURES

5 KINGSPAN CEILING SYSTEM DESIGN POLICY AND PROCEDURES CONT. 13. CONTRACTOR MUST COMPLY WITH ANY AND ALL LOCAL HEALTH AND SAFETY REGULATIONS FOR CONSTRUCTION PROJECTS, INCLUDING ADEQUATE FALL PROTECTION. 14. ALL TRADES ONSITE MUST BE INFORMED BY THE GENERAL CONTRACTOR/SAFETY OFFICER/PANEL INSTALLATION SUBCONTRACTOR REGARDING THE LOADING CAPACITY OF THE CEILING, INCLUDING BUT NOT LIMITED TO ITEM #9 ABOVE PRIOR TO INSTALLATION. 15. IT IS THE RESPONSIBILITY OF THE GENERAL CONTRACTOR/SAFETY OFFICER/PANEL INSTALLATION SUBCONTRACTOR TO PREVENT ANY UNAUTHORIZED ACCESS ON TOP OF THE CEILING DURING CONSTRUCTION ACTIVITY. 16. ALL REFRIGERATION UNITS AND/OR EQUIPMENT MUST BE SUSPENDED AND /OR SUPPORTED INDEPENDENTLY FROM THE CEILING ASSEMBLY. 17. THE PANEL INSTALLATION SUBCONTRACTOR AND GENERAL CONTRACTOR SHALL REVIEW PANEL INSTALLATION DRAWINGS FOR PROPER LAYOUT. 18. THE PANEL INSTALLATION SUBCONTRACTOR SHALL IDENTIFY AND/OR VERIFY FINAL PANEL CUT LIST, INCLUDING PANEL LENGTHS. CEILING SYSTEM DESIGN POLICY AND PROCEDURES

6 CORE DEPTHS: 2", 2.5", 3", 4", 5", 6" STEEL GAUGES: EXTERIOR: 26, 24, 22 INTERIOR: 26, 24, 22 MODULE WIDTH: 42" PANEL ORIENTATION: VERTICAL EMBOSSING: EXTERIOR: STUCCO / SMOOTH INTERIOR: STUCCO / SMOOTH LENGTHS: MINIMUM: 8'-0" MAXIMUM: 53'-0" INTERIOR MINOR RIB 200 SERIES PANEL (MODESTO) 2"-6" EXTERIOR 42" COVERAGE (1,067mm) INVERTED RIB INTERIOR SHADOWLINE 200 SERIES PANEL (DELAND) 2"-6" EXTERIOR INVERTED RIB 42" COVERAGE (1,067mm) INTERIOR "V" GROOVE 200 SERIES PANEL (MODESTO) 2"-6" EXTERIOR INVERTED RIB 42" COVERAGE (1,067mm) PANEL PROFILES 200 SERIES

7 CORE DEPTHS: DELAND: 2", 2.5", 3", 4", 5", 6" STEEL GAUGES: EXTERIOR: 26, 24, 22 INTERIOR: 26, 24, 22 MODULE WIDTH: 42" PANEL ORIENTATION: VERTICAL EMBOSSING: EXTERIOR: STUCCO / SMOOTH INTERIOR: STUCCO / SMOOTH LENGTHS: MINIMUM: 8'-0" MAXIMUM: 53'-0" INTERIOR SHADOWLINE, MINOR RIB, V-GROOVE 300A SERIES PANEL (DELAND) 2"-6" EXTERIOR 42" COVERAGE (1,067mm) AZTECO INTERIOR SHADOWLINE, MINOR RIB, V-GROOVE 300SL SERIES PANEL (DELAND) 2"-6" EXTERIOR 42" COVERAGE (1,067mm) MINOR RIB INTERIOR SHADOWLINE, MINOR RIB, V-GROOVE 300MR SERIES PANEL (DELAND) 2"-6" EXTERIOR 42" COVERAGE (1,067mm) MICRO-RIB INTERIOR SHADOWLINE, MINOR RIB, V-GROOVE 300SR SERIES PANEL (MODESTO) 2"-6" EXTERIOR 42" COVERAGE (1,067mm) STRIATED PANEL PROFILES 300 SERIES

8 INTERIOR FACE MINOR RIB 200 SERIES PANEL 2"-6" EXTERIOR FACE 42" COVERAGE (1,067mm) INVERTED RIB HORIZONTAL SUPPORT MALE LEG COLD SIDE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) FEMALE POCKET FEMALE POCKET CONTINUOUS BUTYL SEALANT (AT "WARM" SIDE JOINT) (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP MALE LEG 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) SET CLIP IN WALL PANEL INSTALLATION DIRECTION NOTE: FILL FEMALE POCKET(S) 3/4 FULL WITH SEALANT TO PROVIDE PROPER AIR/WATER SEAL * VERIFY FIRST PANEL ENGAGEMENT AND ADJUST ACCORDINGLY 200 SERIES EXPANDED JOINT

9 HORIZONTAL SUPPORT COLD SIDE CONTINUOUS BUTYL SEALANT (AT JOINT) (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) WALL PANEL INSTALLATION DIRECTION 200 SERIES ENGAGED JOINT

10 INTERIOR FACE MINOR RIB 300 SERIES PANEL 2"-6" EXTERIOR FACE MINOR RIB 42" COVERAGE (1,067mm) HORIZONTAL SUPPORT MALE LEG COLD SIDE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) FEMALE POCKET FEMALE POCKET MALE LEG CONTINUOUS BUTYL SEALANT (AT "WARM" SIDE JOINT) (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) WALL PANEL INSTALLATION DIRECTION NOTE: FILL FEMALE POCKET(S) 3/4 FULL WITH SEALANT TO PROVIDE PROPER AIR/WATER SEAL * VERIFY FIRST PANEL ENGAGEMENT AND ADJUST ACCORDINGLY 300 SERIES EXPANDED JOINT

11 HORIZONTAL SUPPORT COLD SIDE CONTINUOUS BUTYL SEALANT (AT JOINT) (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) WALL PANEL INSTALLATION DIRECTION 300 SERIES ENGAGED JOINT

12 INTERIOR OF BUILDING EXTERIOR OF BUILDING CONTINUOUS AT PANEL JOINT (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) COLD SIDE 3" Ø 0.28" 14 GA. GALVANIZED HIDDEN CLIP INTERMEDIATE SUPPORT

13 CONTINUOUS AT PANEL JOINT SHIM AS NECESSARY (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP CONCRETE/MASONRY WALL INTERIOR OF BUILDING HAT CHANNEL & FASTENING COLD SIDE 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) 3" Ø 0.28" 14 GA. GALVANIZED HIDDEN CLIP NOTE: CONTACT KINGSPAN TECHNICAL SERVICES FOR RECOMMENDED CLIP SPACING LINER PANEL TO CONCRETE WITH SUPPORT

14 INTERIOR OF BUILDING CONTINUOUS AT PANEL JOINT CONCRETE/MASONRY WALL FASTENERS TO MASONRY SLIP SHEET TO PROTECT PANELS COLD SIDE 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) 3" Ø 0.28" 14 GA. GALVANIZED HIDDEN CLIP NOTE: CONTACT KINGSPAN TECHNICAL SERVICES FOR RECOMMENDED CLIP SPACING LINER PANEL TO CONCRETE

15 * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) SLIP SHEET TO PROTECT PANELS CONCRETE CURB COLD SIDE (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) SET CLIP IN CONCRETE SLAB F.I.P INSULATION BASE TRIM W/ POP 8" O.C. SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT "Z" SHAPED BASE ANGLE *FIELD CUT THERMAL BREAK REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION STAGGERED FLOOR INSULATION SUB SLAB CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE VAPOR BARRIER CONTINUOUS W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT SEE CS-BS /300 FOR HEAVY GAUGE ANGLE APPLICATION & CS-BS /300 FOR LAP TRIM ON "Z" BASE ANGLE NOTES: 1) BASE ANGLE MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL 2) Z SHAPED BASE ANGLE GAUGE TO BE DETERMINED BY PROJECT ENGINEER OF RECORD 3) FLOOR INSULATION REQUIRED FOR FREEZER APPLICATIONS BASE DETAIL - STAGGERED INSULATION W/ LIGHT GAUGE ANGLE

16 "Z" TRIM 2 BEADS OF ON EACH SIDE "Z" TRIM LAP TRIM MIN. 3" TRIM LAP SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) SLIP SHEET TO PROTECT PANELS (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) SET CLIP IN CONCRETE CURB COLD SIDE * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT BASE TRIM W/ POP 8" O.C. SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT CONTINUOUS "Z" TRIM SET IN (SEE LAP TRIM ABOVE FOR "Z" TRIM) HEAVY GA. BASE ANGLE CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE CONCRETE SLAB FIELD CUT THERMAL BREAK FLOOR INSULATION F.I.P INSULATION SUB SLAB REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION CONTINUOUS W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT VAPOR BARRIER NOTES: 1) BASE ANGLE MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL 2) BASE ANGLE GAUGE TO BE DETERMINED BY PROJECT ENGINEER OF RECORD 3) FLOOR INSULATION REQUIRED FOR FREEZER APPLICATIONS BASE DETAIL - INSULATED SLAB W/ HEAVY GAUGE ANGLE

17 LAP TRIM 2 BEADS OF ON EACH SIDE SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) "Z" ANGLE LAP TRIM 3" END LAP 3" END LAP SLIP SHEET TO PROTECT PANELS COLD SIDE (2) 1 4" - HEX HEAD FASTENERS PER PANEL CLIP 14 GA. GALVANIZED 2-HOLE HIDDEN CLIP (1 PER PANEL, PER SUPPORT) SET CLIP IN CONCRETE CURB * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT BASE TRIM W/ POP 8" O.C. SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT CONTINUOUS "Z" TRIM SET IN (SEE LAP TRIM ABOVE FOR "Z" TRIM) HEAVY GA. BASE ANGLE CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE CONCRETE SLAB FIELD CUT THERMAL BREAK FLOOR INSULATION F.I.P INSULATION SUB SLAB REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION CONTINUOUS W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT VAPOR BARRIER NOTES: 1) BASE ANGLE MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL 2) Z SHAPED BASE ANGLE GAUGE TO BE DETERMINED BY PROJECT ENGINEER OF RECORD 3) FLOOR INSULATION REQUIRED FOR FREEZER APPLICATIONS BASE DETAIL - INSULATED SLAB W/ LIGHT GAUGE ANGLE

18 SEALANT(OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) SLIP SHEET TO PROTECT PANELS COLD SIDE CONCRETE CURB * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT POURABLE SEALANT BASE TRIM 1 4 " - 14 STITCH 8" O.C. MIN. 14GA GALVANIZED STEEL BASE CHANNEL CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE CONCRETE SLAB F.I.P INSULATION FIELD CUT THERMAL BREAK STAGGERED FLOOR INSULATION SUB SLAB REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION VAPOR BARRIER NOTES: 1) TWO APPLICATIONS OF POURABLE SEALANT ARE REQUIRED. APPLY FIRST APPLICATION AND ALLOW 24HRS BEFORE APPLYING THE SECOND APPLICATION 2) BASE CHANNEL MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL 3) FLOOR INSULATION REQUIRED FOR FREEZER APPLICATIONS BASE DETAIL - STAGGERED INSULATION W/ LIGHT GAUGE ANGLE

19 COLD SIDE SLIP SHEET TO PROTECT PANELS SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) F.I.P INSULATION FIELD CUT THERMAL BREAK * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT CONCRETE CURB SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT BASE TRIM POURABLE SEALANT 1 4 " - 14" STITCH 8" O.C. MIN. 14GA GALVANIZED STEEL BASE CHANNEL CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE CONCRETE SLAB FLOOR INSULATION SUB SLAB REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION VAPOR BARRIER NOTES: 1) TWO APPLICATIONS OF POURABLE SEALANT ARE REQUIRED. APPLY FIRST APPLICATION AND ALLOW 24HRS BEFORE APPLYING THE SECOND APPLICATION 2) BASE CHANNEL MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL 3) FLOOR INSULATION REQUIRED FOR FREEZER APPLICATIONS BASE DETAIL - INSULATED SLAB W/ CHANNEL

20 COLD SIDE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) MAX. 12" O.C. MIN. 16 GA. GALVANIZED BASE ANGLE CONTINUOUS AT PANEL JOINT CONTINUOUS WITH MARRIAGE BEAD TO SEALANT AT PANEL JOINT MAX. 12" O.C. MIN. 16 GA. GALVANIZED BASE ANGLE FASTENER TO CONCRETE CONCRETE SLAB FASTENER TO CONCRETE (OPTIONAL) FLOOR INSULATION VAPOR BARRIER BASE DETAIL - PARTITION W/ FLOOR INSULATION

21 CONTINUOUS AT PANEL JOINT SLIP SHEET TO PROTECT PANELS COLD SIDE SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) CONCRETE CURB CONCRETE CURB FINISH FLOOR F.I.P INSULATION FIELD CUT THERMAL BREAK CONCRETE SLAB * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT STAGGERED FLOOR INSULATION BASE CHANNEL SUB SLAB CONTINUOUS HEAVY BEAD OF FASTENER TO CONCRETE VAPOR BARRIER REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF BASE CONDITION NOTES: 1) BASE CHANNEL MUST BE FASTENED SECURELY TO SLAB 2) ANGLE IRON MAY BE USED IN LIEU OF CHANNEL BASE DETAIL - INSULATED/ NON-INSULATED FLOOR

22 COLD SIDE SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN) 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL) 1 4 " - 14 THROUGH FASTENERS SLIP SHEET TO PROTECT PANELS CONTINUOUS AT PANEL JOINT ABUSE CURB (NOT BY KINGSPAN - CAN BE POURED AFTER PANEL INSTALLATION) FLOOR INSULATION MIN. 16 GA. GALVANIZED BASE ANGLE FASTENER TO CONCRETE SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT VAPOR BARRIER BASE DETAIL - PARTITION W/ CURBS INSULATED FLOOR

23 CONTINUOUS AT PANEL JOINT OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN) MAX. 12" O.C. W/ MARRIAGE BEAD TO JOINT SEALANT COLD SIDE MAX. 12" O.C. MIN. 16 GA. GALVANIZED BASE ANGLE SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT (OPTIONAL) FASTENER TO CONCRETE THIS DETAIL ASSUMES MINIMAL TEMPERATURE DIFFERENTIAL ON EITHER SIDE OF PANEL BASE DETAIL - PARTITION NON-INSULATED FLOOR

24 COLD SIDE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) CONTINUOUS AT PANEL JOINT 14 GA. GALVANIZED HIDDEN CLIP (1 PER 8" O.C. BASE TRIM SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN - SEE SCHEDULE) 1 4 " - 14 THROUGH FASTENERS MIN. 16 GA. GALVANIZED BASE ANGLE W/ MARRIAGE BEAD TO JOINT SEALANT EXISTING EXTERIOR WALL (OPTIONAL) SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT FASTENER TO CONCRETE THIS DETAIL ASSUMES MINIMAL TEMPERATURE DIFFERENTIAL ON EITHER SIDE OF PANEL BASE DETAIL - LINER PANEL

25 CONTINUOUS AT PANEL JOINT SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN) VAPOR BARRIER MAX. 12" O.C. W/ MARRIAGE BEAD OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) ABUSE CURB (NOT BY KINGSPAN - CAN BE POURED AFTER PANEL INSTALLATION) SLIP SHEET TO PROTECT PANELS COLD SIDE MIN. 16 GA. GALVANIZED BASE CHANNEL FASTENER TO CONCRETE BASE DETAIL - PARTITION W/ CURBS (NON-INSULATED FLOOR)

26 COLD SIDE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN - SEE SCHEDULE) 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL) 1 4 " - 14 THROUGH FASTENERS SLIP SHEET TO PROTECT PANELS CONTINUOUS AT PANEL JOINT ABUSE CURB (NOT BY KINGSPAN - CAN BE POURED AFTER PANEL INSTALLATION) VAPOR BARRIER MIN. 16 GA. GALVANIZED BASE ANGLE FASTENER TO CONCRETE SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT BASE DETAIL - PARTITION W/ CURBS (ALTERNATE)

27 CONTINUOUS AT PANEL JOINT OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) MIN. 16 GA. GALVANIZED BASE CHANNEL SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN) FASTENER TO CONC. CONTINUOUS AT PANEL JOINT MAX. 12" O.C. MIN. 16 GA. GALVANIZED BASE ANGLE OPTIONAL BUTYL (RECOMMENDED FOR WASHDOWN APPLICATIONS) SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN) MIN. 16 GA. GALVANIZED BASE ANGLE FASTENER TO CONC. PARTITION BASE ON TOP OF CURB

28 CONTINUOUS AT PANEL JOINT MIN. 16GA BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) SILICONE SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN - SEE SCHEDULE) CONCRETE CURB (2) 1 4" - 14 X 4" HWH TEK 3 W/O WASHER PER PANEL CLIP FIELD CUT THERMAL BREAK POURABLE SEALANT BT-1 BASE TRIM W/ 1 4 " - 14 X 7 8" LOW PROFILE STITCH 8" O.C. SET PANEL IN CONT. HEAVY BEAD W/ MARRIAGE BEAD TO EXT. PANEL JOINT FOUNDATION FLASHING FASTENERS, SEALANTS, AND WEATHER TIGHTNESS SET BASE CHANNEL IN HEAVY BEAD OF INSULATION NOTES: 1) TWO APPLICATIONS OF POURABLE SEALANT ARE REQUIRED. APPLY FIRST APPLICATIONS AND ALLOW 24HRS BEFORE APPLYING THE SECOND APPLICATIONS 2) BASE CHANNEL MUST BE FASTENED SECURELY TO SLAB TO RESIST LATERAL LOAD APPLIED BY PANEL BASE DETAIL WITH FACE INSULATED SLAB

29 THERMAL CUT PANEL FACE SUFFICIENT ENOUGH FOR METAL TO BE REMOVED REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF CORNER CONDITION OUTSIDE CORNER TRIM MIN. 1 4" GAP FOR F.I.P. INSTALLATION FIELD CUT THERMAL BREAK 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER W/ 1 1 8" BONDED WASHER POP 8" O.C. SELF-ADHERING VAPOR BARRIER (AT - NOT BY KINGSPAN) REMOVE METAL SKIN FROM THERMAL CUT TO EXTERIOR FACE OF PANEL F.I.P. INSULATION 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER W/ 1 1 8" BONDED WASHER POP 8" O.C. 8" O.C. CONTINUOUS BUTYL SEALANT INSIDE CORNER 8" O.C. HORIZONTAL SUPPORT COLD SIDE OUTSIDE CORNER - FLUSH TRIM

30 THERMAL CUT PANEL FACE SUFFICIENT ENOUGH FOR METAL TO BE REMOVED REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF CORNER CONDITION MIN. 1 4" GAP FOR F.I.P. INSTALLATION FIELD CUT THERMAL BREAK 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) POP 8" O.C. F.I.P. INSULATION OUTSIDE CORNER TRIM SELF-ADHERING VAPOR BARRIER AT 8" O.C. 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) POP 8" O.C. COLD SIDE ATTACHMENT CLIP INSIDE CORNER TRIM CONTINUOUS BUTYL 8" O.C. HORIZONTAL SUPPORT OUTSIDE CORNER - PROFILED TRIM

31 WILL VARY WITH FIELD CONDITION WILL VARY WITH FIELD CONDITION FIELD CUT MIN. 1 4" GAP FOR F.I.P. INSTALLATION FIELD CUT THERMAL 8" O.C. F.I.P. INSULATION OUTSIDE CORNER TRIM SELF-ADHERING VAPOR BARRIER (AT - NOT BY KINGSPAN) 8" O.C. INSIDE CORNER 8" 8" O.C. CONTINUOUS OUTSIDE CORNER AT PARTITION

32 FASTENER TO CONCRETE OUTSIDE CORNER TRIM 8" O.C. F.I.P. INSULATION TRANS FLASHING SELF-ADHERING VAPOR BARRIER (AT - NOT BY KINGSPAN) FIELD CUT THERMAL 8" O.C. INSIDE CORNER 8" 8" O.C. CONTINUOUS OUTSIDE CORNER LINER PANEL AT CONC WALL

33 WILL VARY WITH FIELD CONDITION OUTSIDE CORNER TRIM WILL VARY WITH FIELD CONDITION COLD SIDE FIELD 8" O.C. CONTINUOUS BUTYL SEALANT 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER W/ 1 1 8" BONDED WASHER COLD SIDE FIELD CUT THERMAL BREAK REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF CORNER CONDITION F.I.P. INSULATION MIN. 1 4" GAP FOR F.I.P. INSTALLATION 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER W/ 1 1 8" BONDED 8" O.C. HORIZONTAL SUPPORT POP 8" O.C. SELF-ADHERING VAPOR BARRIER INSIDE CORNER TRIM POP 8" O.C. INSIDE CORNER - FLUSH TRIM

34 WILL VARY WITH FIELD CONDITION WILL VARY WITH FIELD CONDITION FIELD 8" O.C. CONTINUOUS BUTYL SEALANT OUTSIDE CORNER TRIM FIELD CUT THERMAL BREAK 1 4 " - 14 THROUGH FASTENER W/ 1 1 8" BONDED WASHER REMOVE METAL SKIN FROM THERMAL CUT TO EXTENT OF CORNER CONDITION F.I.P. INSULATION MIN. 1 4" GAP FOR F.I.P. INSTALLATION 1" POP 8" 8" O.C. HORIZONTAL SUPPORT POP 8" O.C. SELF-ADHERING VAPOR BARRIER INSIDE CORNER TRIM 1 4 " - 14 THROUGH FASTENER W/ 1 1 8" BONDED WASHER INSIDE CORNER - PROFILED TRIM

35 8" O.C. EXTERIOR SELF-ADHERING VAPOR BARRIER INSIDE CORNER TRIM FIELD CUT THERMAL 8" O.C. INTERIOR PARTITION F.I.P. INSULATION EXPANSION FASTENER (TO BE LOCATED ON OPPOSITE SIDE OF THERMAL CUT FROM PANEL'S LEADING EDGE) OPTIONAL BUTYL AT WASH DOWN INSIDE CORNER 8" O.C. STRUCTURAL SUPPORT INTERIOR COLD SIDE NOTES: 1) ADDITIONAL FASTENERS MAY BE REQUIRED ON EITHER SIDE OF THE FIELD CUT THERMAL BREAK BASED UPON ACTUAL DESIGN LOADS AND THERMAL REQUIREMENTS FIELD WITH INSULATION INSULATE SUPPORTING STEEL ON OF PARTITION (APPROX. 4'-0") FIELD NOTCH PANELS AT GIRT LOCATION GIRT CAP TRIM PARTITION WALL INSIDE CORNER TO EXTERIOR WALL

36 CONTINUOUS AT PANEL JOINT COLD SIDE SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) FREEZER DOOR CASING, FASTENERS, SEALANT, & REQUIRED SUPPORT SELF ADHERING VAPOR BARRIER (OPTIONAL - NOT BY KINGSPAN) CONTINUOUS WITH MARRIAGE BEAD TO SEALANT AT PANEL JOINT HEADER CONDITION

37 SEALANT (OPTIONAL - NOT BY KINGSPAN) (INSTALL AFTER TEMP. PULL DOWN ) COLD SIDE SELF ADHERING VAPOR BARRIER (OPTIONAL - NOT BY KINGSPAN) FREEZER DOOR CASING, FASTENERS, SEALANT, & REQUIRED SUPPORT CONTINUOUS JAMB CONDITION

38 COLD SIDE FIELD ROUT PANELS FOR WOOD SPLINE BASE TRIM WITH POP 8" O.C. (PRE-INSTALL WEEP HOLES) CONTINUOUS BUTYL SEALANT FIR SPLINE STACK JOINT TRIM WITH POP RIVETS SET FIR SPLINE IN BUTYL SEALANT CONTINUOUS BUTYL SEALANT MARRIED TO SEALANT IN PANEL JOINT POP 8" O.C. CONTINUOUS AT PANEL JOINT HORIZONTAL SUPPORT 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) NOTES: 1) SEE DETAIL CS-TL /300 AND CS-TL /300 FOR PROPER TRIM LAP DETAILS 2) CONTACT KINGSPAN TECHNICAL SERVICES FOR PROPER PANEL FASTENING REQUIREMENTS STACK JOINT

39 GALVANIZED CAP FLASHING ROOF MEMBRANE SYSTEM ATTACHMENT ROOF MEMBRANE BOARD INSULATION AND ROOF UNDERLAYMENT ROOF MEMBRANE SYSTEM ATTACHMENT SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT RAKE TRIM, FASTENERS, SEALANT AND WEATHER TIGHTNESS SHEETING OR RAKE ANGLE REQUIRED F.I.P. INSULATION COLD SIDE * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT FIELD CUT THERMAL BREAK 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) 1 4 " - 14 THROUGH FASTENERS CONTINUOUS AT PANEL JOINT RAKE

40 GALVANIZED CAP FLASHING ROOF MEMBRANE ROOF MEMBRANE SYSTEM ATTACHMENT CONT. HEAVY BEAD BUTYL SEALANT W/ MARRIAGE BEAD TO EXT. PANEL JOINT INSULATION AND ROOF UNDERLAYMENT FASTENER F.I.P. INSULATION SHEETING OR RAKE ANGLE REQUIRED COLD SIDE RAKE TRIM, FASTENERS, SEALANT AND WEATHER TIGHTNESS SEALANT TO MEMBRANE 200 SERIES CLOSURE SET IN W/ MARRIAGE BEAD TO PANEL JOINT * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT FIELD CUT THERMAL BREAK 1 4 " - 14 THROUGH FASTENERS 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) RAKE W/ MEMBRANE ROOF

41 F.I.P. INSULATION GALVANIZED CAP FLASHING ROOF MEMBRANE ROOF MEMBRANE SYSTEM ATTACHMENT CONT. HEAVY BEAD BUTYL SEALANT W/ MARRIAGE BEAD TO EXT. PANEL JOINT INSULATION AND ROOF UNDERLAYMENT RAKE TRIM, FASTENERS, SEALANT AND WEATHER TIGHTNESS SEALANT TO MEMBRANE FASTENER EAVE STRUT 200 SERIES CLOSURE SET IN W/ MARRIAGE BEAD TO PANEL JOINT * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT FIELD CUT THERMAL BREAK COLD SIDE 1 4 " - 14 THROUGH FASTENERS 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) CONTINUOUS AT PANEL JOINT LOW EAVE

42 ATTIC ABOVE CEILING MUST BE VENTILATED REFER TO KINGSPAN CEILING POLICY DOCUMENT SEE CS-CE /300 FOR ADDITIONAL INFO MARRIAGE BEAD TO PANEL JOINT FIELD CUT THERMAL BREAK MARRIAGE BEAD TO PANEL 8" O.C. (TYP) F.I.P. INSULATION OUTSIDE CORNER TRIM CEILING SELF ADHERING VAPOR BARRIER MARRIAGE BEAD TO PANEL 8" O.C. (TYP) WALL COLD SIDE 8" O.C. (TYP) INSIDE CORNER 8" O.C. (TYP) CONTINUOUS 1 4 " - 14 THROUGH FASTENERS 14 GA. GALVANIZED HIDDEN CLIP (1 PER PANEL, PER GIRT) CONTINUOUS AT PANEL JOINT INTERIOR WALL TO CEILING

43 #10 X 1 3 8" FASTENER AT EVERY PANEL JOINT BOTH SIDES OF PANEL AA CROSS SECTION (SECTION VIEW ) SELF ADHERING VAPOR BARRIER FIELD CUT THERMAL BREAK CEILING SUPPORT ANGLE EXPANSION FASTENER WALL COMPRESSIBLE INSULATION MARRIAGE BEAD TO PANEL JOINT A A #10 X 1 3 8" TEK 1 FASTENER AT EVERY PANEL JOINT (SEE DETAIL ABOVE) WALL TO CEILING INTERSECTION

44 ATTIC ABOVE CEILING MUST BE VENTILATED 3 8 " GALVANIZED HANGER ALL-THREAD ROD (ROD SPACING TO BE DETERMINED) MARRIAGE BEAD TO PANEL JOINT TRANSITION 8" O.C (TYP) INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) HEX NUT AND LOCK WASHER 4" X 4" X 14 GA. PLATE WASHER* SELF ADHERING VAPOR BARRIER INTERIOR FACE OF PANEL CEILING 8" O.C. (TYP) CONTINUOUS FILL 1 2" GAP BETWEEN PANEL WITH F.I.P. INSULATION HEX NUT AND LOCK WASHER EXTERIOR SIDE OF PANEL MUST BE ON BOTTOM OF CEILING. PANEL CUT LIST MUST MATCH THIS ORIENTATION 1 1 2" X 6" X 14 GA. GALVANIZED CEILING CHANNEL (WHITE POWDER COAT - OPTIONAL) (CAP TRIM - OPTIONAL) CONTINUOUS #8 GA. SPLAY BRACE WIRE IN FOUR DIRECTIONS 3 8 " ALL-THREAD HANGER ROD FOUR TIGHT TURNS IN 1 1 2" SEISMIC BRACE PLATE * CONTACT KINGSPAN TECHNICAL SERVICES FOR SEISMIC BRACE PLATE QUANTITY AND LOCATION SEISMIC BRACE PLATE CEILING CHANNEL

45 ATTIC ABOVE CEILING MUST BE VENTILATED 3 8 " GALVANIZED HANGER ALL-THREAD ROD (SPACED NO GREATER THAN 6'-0" O.C.) MARRIAGE BEAD TO PANEL JOINT TRANSITION 8" O.C. (TYP) INTERIOR FACE OF PANEL INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) HEX NUT AND LOCK WASHER 4" X 4" X 14 GA. PLATE WASHER* MARRIAGE BEAD TO PANEL JOINT SELF-ADHERING VAPOR BARRIER CEILING CEILING EXTERIOR SIDE OF PANEL MUST BE ON BOTTOM OF CEILING. PANEL CUT LIST MUST MATCH THIS ORIENTATION 4" X 3" X 3 16" EXTRUDED ALUMINUM CEILING TEE (PAINTED WHITE) CONTINUOUS FILL 1 2" GAP BETWEEN PANEL WITH F.I.P. INSULATION #8 GA. SPLAY BRACE WIRE IN FOUR DIRECTIONS 3 8 " ALL-THREAD HANGER ROD FOUR TIGHT TURNS IN 1 1 2" SEISMIC BRACE PLATE 3 8 "Ø EYE COUPLER NUT 3 8 "Ø x 1 1 2" BOLT WITH (3) 3 8 " WASHERS AND (1) LOCK-NUT PER BOLT * CONTACT KINGSPAN TECHNICAL SERVICES FOR SEISMIC BRACE PLATE QUANTITY AND LOCATION SEISMIC BRACE PLATE CEILING TEE

46 ATTIC ABOVE CEILING MUST BE VENTILATED 3 8 " GALVANIZED HANGER ALL-THREAD ROD WITH NUTS AND WASHER TOP AND BOTTOM COUPLING NUT FIELS DRILL 1 2" HOLES FOR INSTALLATION OF MACHINE BOLTS INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) #10 X 1 3/8" TEK 1 FIELD APPLIED () INTERIOR FACE OF PANEL CEILING CEILING PANEL CLIPS WITH 3 8" MACHINE BOLT PER PANEL JOINT, AT SPACING REQUIRED FOR PANEL DEFLECTION SPANS EXTERIOR SIDE OF PANEL MUST BE ON BOTTOM OF CEILING. PANEL CUTLIST MUST MATCH THIS ORIENTATION NOTE: SUPPLEMENTAL CEILING CLIP IS NOT INTENDED AS A SUBSTITUTE FOR CEILING CHANNEL OR TEE SYSTEM. CONTACT KINGSPAN TECHNICAL SERVICES FOR APPROPRIATE USE. SUPPLEMENTAL CEILING CLIP

47 CEILING TEE SEISMIC BRACE PLATE (IF REQUIRED) TO BE LOCATED AT EVERY THIRD ROD LOCATION IN LIEU OF PLATE WASHER (SEE DETAIL CS-CE /300). CONTACT KINGSPAN TECHNICAL SERVICES FOR VERIFICATION. PROJECT ENGINEER OF RECORD MUST VERIFY ROOF IS CAPABLE OF SUPPORTING CEILING SYSTEM LOADS AS WELL AS PROPER CEILING TO ROOF CONNECTION DETAILS ERECTOR MAY PRE-ASSEMBLE HARDWARE ON 3 8" HANGAR RODS- WIRE TIES HOLD WASHERS ABOVE WORKING POINT HEX NUT ROUND WSHR SPLICE PLATE 4" X 4" X 14 GA. PLATE WASHER WIRE TIE INTERIOR FACE OF PANEL OUTSIDE CORNER TRIM 12" OC. (SEALANT OR VAPOR SEAL TAPE AS REQUIRED) LOCATE FIRST HANGER ROD AT LESS THAN 24" FROM FACE OF PANEL CEILING TEE SPLICE PLATE W/ (4) 3 8" X 1 2" BOLTS, NUTS, AND WASHERS CEILING TEE EXTERIOR SIDE OF PANEL MUST BE ON BOTTOM OF CEILING. PANEL CUTLIST MUST MATCH THIS ORIENTATION SEE DETAIL CS-CE /300 FOR ADD'L INFO. CONTINUOUS BUTYL SEALANT CEILING TEE ASSEMBLY

48 PROJECT ENGINEER OF RECORD MUST VERIFY ROOF IS CAPABLE OF SUPPORTING CEILING SYSTEM LOADS AS WELL AS PROPER CEILING TO ROOF CONNECTION DETAILS FIELD NOTCH END OF CHANNEL TO REST ON TOP OF WALL PANEL ROUND WSHR NUT ERECTOR MAY PRE-ASSEMBLE HARDWARE ON /8" HANGER RODS- WIRE TIES HOLD WASHER ABOVE WORKING POINT 4" X 4" X 14 GA. PLATE WASHER WIRE TIE 2'-0" MAX. INTERIOR FACE OF PANEL CEILING CHANNEL SPLICE PLATE 9/16" DIA. HOLES PRE-PUNCHED FOR 3/8" OR ALL-THREAD ROD AT 5'-0" O/C (DO NOT SPACE ALL-THREAD RODS FURTHER THAN 60" APART. THE SPAN FROM WALL TO FIRST ROD, SHALL BE NO GREATER THAN 24".) EXTERIOR SIDE OF PANEL MUST BE ON BOTTOM OF CEILING. PANEL CUTLIST MUST MATCH THIS ORIENTATION CEILING CHANNEL ASSEMBLY

49 ATTIC ABOVE CEILING MUST BE 8" O.C. SELF ADHERING VAPOR BARRIER CONTINUOUS BUTYL SEALANT IN JOINT UP TO MEMBRANE TERMINATION W/ MARRIAGE BEAD TO JOINT SEALANT INSIDE CORNER 8" O.C. F.I.P. INSULATION CEILING FIELD CUT THERMAL BREAK * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT CONTINUOUS BUTYL SEALANT AT "WARM" SIDE PANEL JOINT CONTINUOUS BUTYL SEALANT EXPANSION FASTENER EXPANSION FASTENER 16 GA. SUPPORT ANGLE COVER 8" O.C. CONTINUOUS BUTYL SEALANT NOTE: CONTACT KINGSPAN TECHNICAL SERVICES FOR ENGINEERING ASSISTANCE CEILING TO WALL - LONGITUDINAL

50 ATTIC ABOVE CEILING MUST BE VENTILATED 3 8 " GALVANIZED HANGER ALL-THREAD ROD (ROD SPACING TO BE DETERMINED) SELF ADHERING VAPOR 8" O.C. 1 4 " MAX DISTANCE BETWEEN PANEL EDGE AND THREAD ROD W/ MARRIAGE BEAD TO JOINT SEALANT INSIDE CORNER 8" O.C. CONTINUOUS BUTYL SEALANT IN JOINT UP TO MEMBRANE TERMINATION W/ MARRIAGE BEAD TO JOINT SEALANT F.I.P. INSULATION FIELD CUT THERMAL BREAK CEILING * ENSURE THERMAL BREAK CUT IS DEEP ENOUGH TO CUT METAL AT PANEL JOINT CONTINUOUS BUTYL SEALANT EXPANSION FASTENER EXPANSION FASTENER 16 GA. SUPPORT ANGLE HEX NUT AND LOCK WASHER COVER 8" O.C. (TYP) CONTINUOUS BUTYL SEALANT NOTE: CONTACT KINGSPAN TECHNICAL SERVICES FOR ENGINEERING ASSISTANCE CEILING TO WALL - TRANSVERSE

51 COMPRESSIBLE INSULATION ROOF DECK A EXPANSION FASTENERS AS REQUIRED COMPRESSIBLE INSULATION SUPPORT ANGLE (SET IN ) PURLIN A PARTITION TO ROOF (PERPENDICULAR TO PURLIN) ROOF DECK FIELD FILL WITH] INSULATION FIELD NOTCH PANELS AT PURLIN LOCATIONS KINGSPAN TO SUPPLY FLAT-STOCK SHEETING TO BE FIELD FORMED FOR PANEL CLOSURES COMPRESSIBLE INSULATION PURLIN AA CROSS SECTION (SECTION VIEW -- TYPICAL AT EACH PURLIN) PARTITION TO ROOF

52 ROOF DECK FILL VOIDS WITH FOAM BLOCK, SET IN FIELD CUT PANELS AS REQUIRED 1 4 " - 14 STITCH TEKS AT EACH PURLINS PURLINS CLOSURE TRIM TO BE FIELD CUT TO FIT AT PURLINS FLANGES. USE SILICONE TO SEAL ALL EDGES WHEN COMPLETE. 1 4 "- 14 STITCH TEKS AT EACH PURLINS SUPPORT ANGLE (SET IN ) ATTACH PURLINS CLOSUE W/ POP RIVETS COMPRESSIBLE INSULATION PARTITION TO ROOF (WITH FOAM BLOCKING) (PERPENDICULAR TO PURLIN) ROOF DECK COMPRESSIBLE INSULATION EXPANSION FASTENERS AS REQUIRED SUPPORT ANGLE SET IN PARTITION TO ROOF (PARALLEL TO PURLIN) PARTITION TO ROOF WITH BLOCKING

53 3 8 " GALVANIZED HANGER ALL-THREAD ROD WITH NUTS AND WASHER TOP AND BOTTOM LOCK NUT COUPLING NUT LOCK NUT FIELD DRILL 1 2" HOLES FOR INSTALLATION OF MACHINE BOLTS 1/4" -14 x 7/8" DP1 VRT INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) LOCK NUT 4" X 4" X 14 GA. PLATE WASHER* 1/4" -14 x 7/8" DP1 VRT INTERIOR FACE OF PANEL CEILING CEILING 3 8 " x 6" CARRIAGE BOLT FIELD APPLIED () PANEL CLIP ALTERNATE CEILING CLIP AT JOINT SERIES ONLY

54 C L MAXIMUM 6'-0" ROD SPACING MAXIMUM 6'-0" ROD SPACING 3 8 " GALVANIZED HANGER ALL-THREAD ROD WITH NUTS AND WASHER TOP AND BOTTOM (SPACING AS REQUIRED) JAMB NUT COUPLING NUT JAMB NUT CONTINUOUS BUTYL SEALANT WITH MARRIAGE BEAD TO WARM SIDE JOINT, TYP. INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) HEX NUT W/ WASHER 4" X 4" X 14 GA. PLATE WASHER W/ (4) 1/4" -14 X 7/8" DP1 VRT MEMBRANE TAPE FIELD APPLIED () 1/4" -14 X 7/8" DP1 VRT 1/4" -14 X 7/8" DP1 VRT PANEL CLIP CONTINUOUS BUTYL SEALANT TRANSITION TRIM 3 8 " x * CARRIAGE BOLT (* PANEL THICKNESS + 3") CONTINUOUS BUTYL SEALANT FILL 1 2" GAP BETWEEN PANEL WITH F.I.P. INSULATION ALTERNATE CEILING CLIP AT BUTT JOINT SERIES ONLY

55 C L MAXIMUM 6'-0" ROD SPACING MAXIMUM 6'-0" ROD SPACING 3 8 " GALVANIZED HANGER ALL-THREAD ROD WITH NUTS AND WASHER TOP AND BOTTOM (SPACING AS REQUIRED) JAMB NUT COUPLING NUT INSULATE HANGER RODS AS REQUIRED (NOT BY KINGSPAN) HEX NUT W/ WASHER 4" X 4" X 14 GA. PLATE WASHER W/ (4) 1/4" -14 X 7/8" DP1 VRT JAMB NUT FIELD APPLIED () 1/4" -14 X 7/8" DP1 VRT 1/4" -14 X 7/8" DP1 VRT PANEL CLIP 3 8 " x * CARRIAGE BOLT (* PANEL THICKNESS + 3") ALTERNATE CEILING CLIP AT INTERMEDIATE SERIES ONLY

56 #8 GA. SPLAY BRACE WIRE IN FOUR DIRECTIONS 3 8 " ALL-THREAD HANGER ROD FOUR TIGHT TURNS IN 1 1 2" SEISMIC BRACE PLATE SEISMIC BRACE PLATE

57 1" MAX 1" MAX POP RIVETS SPACE AS REQUIRED MAX 1" MAX 1" MAX MIN. 3" TRIM LAP 3" (2) BEADS MIN. 3" TRIM LAP TRIM END LAP

58 FIELD NOTCH HEM(S) AS REQUIRED 1" MAX 1" MAX POP RIVETS SPACE AS REQUIRED MAX 1" MAX 1" MAX MIN. 3" TRIM LAP 3" (2) BEADS MIN. 3" TRIM LAP TRIM LAP WITH HEM

59 POP RIVETS SPACE AS REQUIRED 1" MAX 1" MAX 3" MAX 3" MAX 1" MAX (2) BEADS 8" LONG LAP STRIP NOM. 1 4 " GAP TRIM END LAP WITH LAP STRIP

60 NOTE: DETAIL SHOWN IS FOR GENERAL USE ONLY (NOT FOR COOLER/FREEZER APPLICATIONS). SEALANT END DAM 2 INTERIOR HEAD TRIM WITH TABS BENT DOWN FIELD NOTCH AND OVERLAP TRIMS, POP RIVET AND SEAL AS NECESSARY FIELD MITER AND OVERLAP TRIMS, POP RIVET AS NECESSARY INTERIOR CAP TRIM AT HEAD EXPOSED SEALANT EXTERIOR CAP TRIM AT HEAD 5 EXTERIOR HEAD TRIM W/ FIELD DRILL 3 8" Ø WEEP HOLES INTERIOR JAMB TRIM 1 SILL TRIM WITH TABS BENT UP 6 3 EXTERIOR CAP TRIM AT JAMB FIELD CUT/NOTCH CAP TRIM AT CORNERS TO ALLOW FOR LAP 4 EXTERIOR JAMB TRIM FIELD CUT/NOTCH CAP TRIM AT CORNERS TO ALLOW FOR LAP EXTERIOR CAP TRIM AT SILL TRIM INSTALLATION SEQUENCE: 1 INTERIOR JAMB TRIM 2 INTERIOR HEAD TRIM WITH TABS DOWN 3 SILL TRIM WITH TABS UP 4 EXTERIOR JAMB TRIM 5 EXTERIOR HEAD TRIM 6 EXTERIOR SEALANTS AS REQUIRED FIELD MITER AND OVERLAP TRIMS, POP RIVET AND SEAL AS NECESSARY TRIM LAP AT FRAMED OPENING