PRODUCT DATA SHEET SikaCor -277

Transcription

1 PRODUCT DATA SHEET Epoxy resin-based coating material for wear resistant coatings PRODUCT DESCRIPTION SikaCor-277 is a thixotropic epoxy resin based 2-pack coating material for steel and concrete. SikaCor-277 has been tested in combination with glass fabric for its crack sealing properties. Low solvent content referring to the directive VdL-RL 04 of the Verband der Lackindustrie für Korrosionsschutz- und Beschichtungsstoffe (Paint Industry Association for and Coating Materials). USES PROPERTIES TESTS SikaCor-277: Primer and thick layer coating For concrete, cement mortar and steel. As a protective coating against chemically aggressive media e.g. In sewage systems for coating wall and floor surfaces and mechanically stressed surfaces e.g. bridge troughs. If need in combination with a fabric layer moderate crackbridging properties can be achieved. - Very good corrosion resistance - Very good adhesion to concrete, cement mortar, PCC, SPCC and fibre cement and steel - Mechanically resistant, tough, friction, impact and shock resistant - Excellent chemical resistance - Crack bridging properties in commendation with glass fabric APPROVAL / STANDARDS Tested for crack bridging properties in accordance with Zulassungsgrundsätze für Beschichtungssysteme für Auffangwannen, Auffangräume und Flächen aus Beton in Anlagen zum Abfüllen und Umschlagen wassergefährdender Flüssigkeiten (principles for approving coating systems for collecting containers, collection areas and surfaces made of concrete in systems for emptying and transferring water contaminating fluids), issued October 2003 at the Polymer Institut Dr. Stenner GmbH, test report numbers 4039 and /5

2 PRODUCT DATA COLOUR SHADES Approx. RAL 1014, RAL 7010, RAL 7030, RAL 7032, RAL 7035 Slight colour deviations are possible due to raw material characteristics. PACKAGING SikaCor-277: 10 kg net. Sika Thinner K: 25; 10 and 3 l SHELF LIFE Originally sealed packaging storage in cool and dry environment: 2 years. SYSTEMS COATING SYSTEMS SUBSTRATE QUALITY (CONCRETE) Thick layer coating: 2 x SikaCor-277 on PCC, ECC or PC filler Material requirement: kg/m² Apart from applications on small areas, the dry film thickness may not exceed 500 μm per layer or 1000 μm in total. Crack-bridging coating composition: Composition for maximum crack openings of 0.40 mm (see test report number ; order quantity 1.7 kg/m² in 2 applications) - Icoment-520 scratch coat 1200 g/m² - Icoment-520 fine mortar 1800 g/m² - SikaCor-277 embedding layer 1000 g/m² - Sika Betonol special fabric 300 g/m² - SikaCor-277 topcoat 700 g/m² - SikaCor EG-5 top coat*) 100 g/m² Composition for maximum crack openings of 0.60 mm (see test report number 4039; order quantity 2.8 kg/m² in 2 applications) Note: For small areas only - Icoment-520 scratch coat 1200 g/m² - Icoment-520 fine mortar 1800 g/m² - SikaCor-277 embedding layer 1000 g/m² - Sika Betonol special fabric 300 g/m² - SikaCor-277 topcoat 1800 g/m² - SikaCor EG-5 top coat*) 100 g/m²*) *) The top coat is not binding for crack bridging Steel: Chemically and mechanically-stressed surfaces: 2-3 x SikaCor-277 The substrate must have sufficient load-bearing capacity (min. C20/25 or ZE 30); average bond strength fctm must be 1.5 N/mm². SURFACE PREPARATION The concrete substrate must be dry (substrate moisture content < 4%), keyed, free from loose parts and sand, cement slurry, dust and other contaminants. Suitable surface preparation processes corresponding to relevant codes of practice shall be applied. Steel: Blasting to preparatory grade, Sa 2 ½ according to DIN EN ISO 12944, part 4. Free from dirt, grease and oil. 2/5

3 TECHNICAL DATA MATERIAL CONSUMPTION Product Specific gravity liquid kg/l by vol. Solids content % by weight Theoretical material-consumption/voc without loss for medium dry film thickness dry microns wet microns kg/m² VOC g/m² SikaCor MIXING RATIO (COMPONENTS A : B) By weight 80 : 20 BENDING TENSILE STRENGTH SikaCor-277: N/mm² (in accordance with DIN 1164) COMPRESSIVE STRENGTH SikaCor-277: 50 N/mm² (in accordance with DIN 1164) RESISTANCE CHEMICAL RESISTANCE Fresh water, seawater, dilute acids and alkalis, salts, mineral and heating oil, grease oils, detergents etc. No long-term resistance to phenol or products containing phenol, highly concentrated acids, formic acid, acetic acid or lactic acid. TEMPERATURE RESISTANCE Dry heat up to C, wet heat and hot water up to +60 C; short term peak loads of up to max C possible. SikaCor-277 is not resistant to fluctuating temperature loads. CRACK BRIDGING No incipient crack of crack width of 0.40 mm (test report ) No incipient crack of crack width of 0,60 mm (test report 4039) HINTS OF APPLICATION MIXING INSTRUCTIONS / MIXING TIME APPLICATION METHOD APPLICATION CONDITIONS Stir component A mechanically before mixing. Add components A+B carefully in the prescribed mixing ratio before processing. To prevent splashing or spilling of the liquid, combine the components with a variable-speed electric mixer (stepless regulation) at a low speed for a short period. Then increase the mixing speed to maximum 300 rpm for intensive mixing. The mixing duration is at least 3 minutes and is complete when the two components have combined to form an homogenous mixture. Decant the mixture into a clean container and mix again once more as described above. Wear suitable safety gloves, a rubber apron, a long-sleeved top, work trousers and tightlyfitting safety goggles/face guard when mixing and decanting the products. Brush or roller Airless spraying: High performance airless device Spraying pressure at the nozzle at least 180 bar. Nozzles from mm, spray angle Minimum material temperature 30 C when processing with continuous water heater. Min. + 5 C (material and surface) Relative humidity: Max. 85 %, except the surface temperature is significantly higher than the dew point temperature, it shall be at least 3 K above dew point. If necessary max. 5% Sika Thinner K may be added to adapt the viscosity. 3/5

4 POTLIFE Product + 10 C + 20 C + 30 C SikaCor min min min. WAITING TIME BETWEEN COATS Dry film thickness + 5 C + 15 C + 20 C + 30 C Can be walked on 300 μm 48 h 24 h 12 h 8 h FINAL DRYING TIME THINNER AND CLEANING OF EQUIPMENT IMPORTANT NOTICE EU DIRECTIVE 2004/42/EC (DECOPAINT) CE-MARKING DIN EN CE-MARKING DIN EN VALUE BASE LOCAL RESTRICTIONS Coverage time 300 µm 72 h 36 h 24 h 12 h Sanded surfaces can be covered at any time up to 1 month after. At 20 C and good ventilation 5-7 days Sika Thinner K For the product category IIA / j, Type Sb, the maximum permissible content of VOC according to the EU Directive 2004/42/EC is 500 g/litre (limit 2010). The maximum VOC-value of SikaCor-277 is below 500 g/litre. The harmonized European Standard EN Screed material and floor screeds Screed materials properties and requirements specifies requirements for screed materials for use in floor construction internally. Structural screeds or coatings, i.e. those that contribute to the load bearing capacity of the structure, are excluded from this standard. Resin floor systems as well as cementitious screeds meet the specification. They have to be CE-labelled as per Annex ZA. 3, Tables ZA 1.1 or 1.5 and ZA 3.3 and fulfil the requirements of the given mandate of the Construction Products Directive (89/106): The harmonized European Standard EN Products and systems for the protection and repair of concrete structures Definitions, requirements, quality, control and evaluation of conformity Part 2: Surface protection systems for concrete gives specifications for products and systems based on methods hydro-phobic impregnation, impregnation and coating for the various principles presented under Products which meet the specification have to be CE-labelled as per Annex ZA. 1, Tables ZA 1a to ZA 1g according to the scope and relevant causes there indicated, and fulfil the requirements of the given mandate of the Construction Products Directive (89/106): For flooring systems not dedicated to protect or reinstate the integrity of a concrete structure, EN applies. Products acc. EN used as flooring systems with mechanical loads also must fulfil EN Here below indicated are the minimum performance requirements set by the standard. For the specific performance results of the product to the particular tests, please see the actual values above in the PDS. All technical data stated in this are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. Please note that as a result of specific local regulations the performance of this product may vary from country to country. Please consult the local for the exact description of the application fields. 4/5

5 2017 Sika Deutschland GmbH HEALTH AND SAFETY INFORMATION LEGAL NOTES GISCODE: RE 1 This coding enables additional information and help with the creation of operating instructions (WINGIS online) to be obtained on the BG Bau service pages ( Skin contact with epoxy resins can lead to allergies! Avoid direct skin contact at all costs when handling epoxy resins! For the selection of suitable protective equipment, we have made our information data sheets 7510 General notes on occupational safety and 7511 General notes for wearing protective gloves available at In conjunction with this we also recommend the BG Bau service pages for Information regarding the handling of epoxy resins ( Information on the safe handling of chemical products, as well as the essential physical, safety-related, toxicological and ecological data can be found in the current safety data sheets. Observe all relevant regulations, e.g. the hazardous substances act. Further notes and information data sheets on product safety and disposal can be found on the Internet at The information, and, in particular, the recommendations relating to the application and enduse of Sika products, are given in good faith based on Sika s current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika s recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the product s suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. The most recent product data sheet applies. This can be requested from us or is available to download at Please check availability of local product data sheet at your local website. In cases of doubt the German text is valid. Sika Deutschland GmbH Industrial Coatings Rieter Tal Vaihingen / Enz Germany Version given by Industrial Coatings Phone: (07042) Fax: (07042) Mail: industrial-coatings@de.sika.com 5/5