Infinity Perimeter Trim

Transcription

1 INSTALLATION INSTRUCTIONS Infinity Perimeter Trim Infinity Infinity R (Reveal) Infinity Z (Razor Edge) Infinity D (Drywall) Infinity RD (Reveal for Drywall) Infinity ZD (Razor for Drywall) Paired Infinity Bracket Always follow good safety practices. Metal edges are sharp, take appropriate precautions. Prior to beginning the installation ensure that all materials are received and in good condition. Record any shipping damage on the carriers bill of lading and contact CMC immediately to order replacement material. Fax replacement material orders, including a purchase order number to Tools Flathead screwdriver Phillips screwdriver Tape measure Leveling device (laser) Marking tool (pencil) Clean gloves Aviation pliers (for hanger wire installation) Tin snips (in case cutting is required) Latex caulk 2 Prep epar aration ation 2.01 Verify weather tightness of the area and begin installation only after wet trades have completed their work and temperature and humidity conditions closely approximate interior conditions which will exist when the area is complete and occupied Locate and review the project installation drawing and details provided Infinity Trim are individually identification marked and their location is shown in the project installation drawing.

2 3 Hangers 3.01 Install hanger wires at locations shown on the project installation drawing. Note: Hanger wires are typically not included with Infinity Trim and must be ordered separately. Hanger Wire 4 Grid 4.01 Install main and cross tees as shown in project installation drawing Add hanger wires to support any unsupported cantilevered grid Cut grid to form intersections with Infinity Trim using the appropriate cross section(s) shown below / / /16 Infinity Infinity R (Reveal) Infinity Z (Razor Edge) 7 /16 7 / /16 Infinity D (Drywall) Infinity RD (Reveal for Drywall) Infinity ZD (Razor for Drywall)

3 5 Infinit inity y Trim 5.01 Locate and identify Infinity Trim parts relative to the grid layout as indicated on the project installation drawing Attach Infinity Trim end-to-end using 414 splice plates and secure with screws provided. Do not overtighten Splice Plate 5.03 For acoustical panel Infinity applications 5.03 For drywall Infinity applications 430 Splice Plate 5.03 Attach Infinity Trim to grid with 430 Grid Clip. Secure 430 clip to trim within groove. Screw grid to clip using two 404 ( 8 self drilling) screws Horizontal Multi-angle Splice Plate Outside Corner Splice Plate Add bead of caulk to inside joints to minimize light leaks Inside Corner Splice Plate 5.05 Brace 5.04 Attach Infinity Trim at corner using inside corner bracket 417, outside corner bracket 429, and multi-angle razor bracket 447. Secure with screws provided. Do not overtighten Add bracing as needed for larger profile Infinity Trim components.

4 METAL: Infinity / Installation 6 Panels 6.01 Cut holes for sprinklers, lights, etc., as required prior to installing panels Cut perimeter panels to fit and install When installing CMC Planostile Snap-in panels, use 448 Grid Adapter Clips and Wall Springs Acoustical panel with Infinity Perimeter Trim 448 Grid Adapter Clip Wall Spring 6.03 Planostile panel with Infinity Perimeter Trim 6.03 Planostile panel with Infinity R Perimeter Trim 6.03 Planostile panel with Infinity Z Perimeter Trim 7 Pair aired Infinit inity Trim 7.01 Locate and identify trim parts as indicated on project installation drawing Install hanger wires at location shown on project installation drawing (4 increments). Note: Hanger wires are typically not included with Infinity Trim and must be ordered separately Pair Infinity Trim components together using ( 3 /4 opening) or (1 3 /8 opening) Brackets. Brackets slide within Infinity Trim groove to set position Attach Infinity Trim end to end using 414 Splice Plate. Secure with provided screws (do not overtighten). See Attach Infinity Trim at corners using 417 Inside Corner Bracket and 429 Outside Corner Bracket. Secure with provided screws (do not overtighten). See Brackets B A Panel Spacing A = 2-1/4 panel to panel face A = 2-7/8 panel to panel face B = 3/4 open between panels B = 1-3/8 open between panels

5 8 Drywall all (Infinit inity y D/RD /RD/ZD ZD) 8.01 Install drywall grid framing as shown on project installation drawings Cut grid to form intersections with Infinity Trim using appropriate cross section(s) shown below Install Infinity Trim (see Section 5 Infinity Trim for details) Install 5 /8 gypsum board as specified in project installation drawing Lay out drywall surface with chalk/pencil lines and cut with router or drywall knife Attach drywall to drywall grid system using selfdrilling or standard bugle head drywall screws. Check for protrusion of screw heads by drawing a finishing knife across the entire surface length Screw 5 /8 drywall to furring grid system 8.07 Tape and mud using industry standard drywall joint procedures. Note: Tape should not overlap the Trim shoulder profile Apply paint according to manufacturer instructions. Trim is treated with a chemical coating for bonding of joint compound and paint Add bracing as needed for larger profile Infinity Trim components Tape and mud 7 /16 7 /16 Brace Infinity D (Drywall) Infinity RD (Reveal for Drywall) 5 11 /16 Infinity ZD (Razor for Drywall) 8.09 Brace

6 9 Components 10 Cleaning Infinity / Infinity D Infinity R / RD 6 Infinity Z / ZD Select a mild, non-abrasive cleaning agent typically used for cleaning painted or reflective surfaces. Never use abrasive cleaning agents as such treatments may scratch, mar, alter, discolor, and/ or remove the finish Before cleaning the finish, perform a trial test on a section of the finish that will be hidden from view once installed. This will insure that the cleaning agent selected is appropriate and will not damage the finish in question Once an appropriate cleaning solution has been selected, care should be taken to use only that amount which is necessary. Do not soak the ceiling components with the solution Use a clean soft sponge or cloth when applying the cleaning agent in order to insure that the applicator does not contain any abrasive elements that may damage the finish in question Any excess cleaning solution should be removed immediately so that the solution does not dry and possibly leave a residue. In the event that a large area needs to be cleaned, it s advisable to break the area down into smaller, more manageable sections so that adequate time is available to complete each phase of the cleaning cycle After cleaning the soiled or smudged area, wipe the surface with a dry soft cloth to remove any residual cleaning solution and dry the area. Use a clean damp cloth to remove any residue that cannot be removed with the dry cloth. Repeat the drying process After the components are clean, allow a few minutes for air drying before installation. It is important that the clean components are dry because other ceiling material, such as insulation, which may come into contact with the cleaned components, can be susceptible to damage from moisture. Ceiling Systems and Specialty Products - USA and Canada: / Fax: / chicagometallic.com CHICAGO / BALTIMORE / LOS ANGELES / BELGIUM / DENMARK / UK / GERMANY / FRANCE / HONG KONG / PRC / MALAYSIA / UNITED ARAB EMIRATES / MEXICO Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation Chicago Metallic Corporation All Rights Reserved M-INSTALL-Infinity-0906 Printed in USA