DeZign Glue Down Luxury Vinyl

Transcription

1 DeZign Glue Down Luxury Vinyl v.8-17

2 Concrete Tiles Tumbled Marble Tiles Pearl 18 x 18 x 3mm DEDST-509 $3.38/sf Sunkissed 18 x 18 x 3mm DEDST-074 $3.38/sf Gray 18 x 18 x 3mm DEDST-076 $3.38/sf Moon Dust 18 x 18 x 3mm DEDST-377 $3.38/sf Lunar 18 x 18 x 3mm DEDST-383 $3.38/sf Earth 18 x 18 x 3mm DEDST-031 $3.38/sf Travertine Tiles Oyster 18 x 18 x 3mm DEDST-381 $3.38/sf Opel 18 x 18 x 3mm DEDST-029 $3.38/sf Bone 18 x 18 x 3mm DEDST-042 $3.38/sf Beige 18 x 18 x 3mm DEDST-044 $3.38/sf Griege 18 x 18 x 3mm DEDST-046 $3.38/sf Bliss 18 x 18 x 3mm DEDST-047 $3.38/sf Glue Down System Can be Ungrouted or Grouted with Acrylic Based Grout Pressed Beveled Edge 22mil Wear Layer Lifetime Residential Warranty; 10 Year Heavy Commercial Warranty FloorScore Indoor Air Quality Certified

3 Platform Planks Comfort Planks Dune 6 x 48 x 3mm DEDV-421 $2.78/sf Chestnut 6 x 48 x 3mm DEDV-420 $2.78/sf Sahara 6 x 36 x 2mm DECOM-067 $1.58/sf Chamois 6 x 36 x 2mm DECOM-054 $1.58/sf Hazelnut 6 x 48 x 3mm DEDV-122 $2.78/sf Autumn 6 x 36 x 2mm DECOM-175 $1.58/sf Aston 6 x 36 x 2mm DECOM-879V $1.58/sf Pressed Beveled Edge 22mil Wear Layer Lifetime Residential Warranty; 10 Year Heavy Commercial Warranty Montana 6 x 36 x 2mm DECOM-514 $1.58/sf 12mil Wear Layer 25 Year Residential Warranty; 5 Year Light Commercial Warranty

4 Earth 6 x 36 x 2mm DESPA-067 $1.38/sf American Cherry 6 x 36 x 2mm DESPA-020 $1.38/sf Sparta Planks Hickory 6 x 36 x 2mm DESPA-774 $1.38/sf Montana Maple 6 x 36 x 2mm DESPA-620 $1.38/sf 6mil Wear Layer 25 Year Residential Warranty; 5 Year Light Commercial Warranty Installation For full details, please visit: Moisture Testing It is the flooring contractor s as well as the installer s responsibility to test all concrete substrates, both new and old, for moisture content to determine if it is sufficiently dry. A concrete slab shall be cured a minimum of 90 days (preferably 120 days) before running moisture tests. These time periods are absolute minimum and concrete may require additional drying time dependent upon local environment conditions. A moisture vapor retarder, such as a 10mil polyethylene sheet or equivalent, is recommended. Radiant Heat Floors DeZign flooring may be installed over radiant heated floors, provided the operating temperature does not exceed 85ºF. NOTE: During installation, lower the radiant heated floor temperature to a minimum 65ºF. This temperature should be maintained for at least 24 hours before, during, and 48 hours after completion of the installation. On ground floors the radiant heating system should have a proper moisture barrier beneath it. Heating pipes must be at least 2 below the floor surface. If the heating pipes are too close to the vinyl flooring, the vinyl may discolor. Gradually increase temperature in increments of 5 per hour. Expansion Joints Expansion joints allow for movement between two concrete slabs. If flooring is installed over an expansion joint, adhesive bond failure, buckling, and cracking of the flooring material is likely to occur. Do not install over expansion joints. Flooring material shall be cut to either side of the joint and then covered with an expansion joint cover. Use a cover that will provide a smooth transition and prevent a tripping hazard. Self-Leveling Compounds A cement, latex reinforced type with a minimum compressive strength of 3,500 PSI or greater is recommended. We do suggest they be obtained from a quality manufacturer that provides a warranty for this product s use as a tile flooring underlayment. NOTE: All warranties and guarantees regarding the suitability and performance of these products, rests with the levelers manufacturer or the installation contractor, not with DeZign. Wood Substrate Construction Suspended wood substrates shall be 1 or thicker, double construction, strongly constructed, free from spring, and have minimum of 18 of well-ventilated air space clearance above the ground. A moisture vapor retarder (10 mil or thicker polyethylene sheeting) should be installed over the ground with overlapped widths and lengths, to reduce moisture vapor transmission. The joists shall be spaced not more than 16 on centers. If joists are warped or twisted, have high crowns, or otherwise do not present a flat, true base for the substrate, these conditions must be corrected before installing substrate. All substrate panels must be fastened to the joists in accordance with their manufacturer s recommendations to preserve their warranties. NOTE: Protruding fasteners must be made flush with the surface of the subfloor panels before beginning installation of underlayment. Existing Resilient Floors Due to the problems associated with the removal of old flooring products and their adhesives, it may be desirable to leave the existing flooring intact. Many installations over existing floors are satisfactory, however their success is dependent upon the condition of the existing floor covering. Leaving old floor covering down increases the possibility of indentations, telegraphing of the old floor, and poor adhesion. There is also a high degree of risk with cemented installations over sheet vinyl flooring with unfilled wear surfaces, urethane finishes, and old floor coverings installed on concrete that show evidence of excessive moisture or alkali. Adhesive Application DeZign flooring requires a premium wet-set adhesive. Apply adhesive per manufacturer s instructions, and only apply an amount of adhesive that can be covered within 20 minutes. Flooring must be installed while adhesive is wet. As they are installed, periodically roll with a 100 lb. sectional floor roller across the width and length of the installation to flatten the adhesive ridges and to expel any entrapped air. Use a hand roller in areas not reached by the 100 lb. roller. DeZign offers a pressure sensitive adhesive that covers 300sf per gallon and is available in 1 gallon and 4 gallon containers.

5 Installation (cont.) To ensure the best color match when installing from two or more cartons, make sure the run numbers on each carton are the same. Work from multiple cartons to ensure proper variation. Begin laying along the guideline taking into consideration the length of the last plank in the row. The first and last plank in each row shall not be less than the width of the plank. Lay the first few planks perfectly on the guideline as this will affect the entire installation. Make sure each plank is flush against the adjoining plank. Lay planks in a pyramid fashion. Take care to place planks as accurately as possible without sliding them into place. Make sure planks are well seated into the adhesive, paying special attention to the edges. Periodically lift a plank to make sure there is good transfer of adhesive to the back of the plank. When finished, roll the entire floor area with the 100 lb. sectional floor roller. Care & Maintenance Initial Care After Installation Immediately after installation, the floor should be dry vacuumed to remove all dust and debris. Wipe with a no wax vinyl flooring cleaner using a sponge mop or similar cloth-applicator mops. Be sure to follow the vinyl cleaner manufacturer s instructions. After 5-10 minutes, all residue of the cleaning agent should be removed and the floor should be rinsed with a damp mop. Allowed to dry for at least 30 minutes before walking on it. Important: Always remove excess water as it may cause slip and fall hazards. Use soft cleaning towels to spread the cleanser and to clean afterwards. Do not use hard towels made from fiber, cotton, and other abrasive material. Do not use soap-based detergents, caustic cleaners, or abrasive cleaners. Avoid exposure to direct sunlight for prolonged periods, as this can cause discoloration. Weekly Maintenance Follow the same instructions as under Initial care after installation. Periodic Maintenance Depending on the amount of traffic, a vinyl floor refresher might help to restore the floor s original beauty. Heat up damaged planks or tiles to release the adhesive in order to replace with new pieces. Alexandria, VA I Chantilly, VA I Fairfax, VA I Richmond, VA I Virginia Beach, VA North Bethesda, MD* I Owings Mills, MD* I Greensboro, NC I Raleigh, NC Locally Owned & Operated