1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.
|
|
|
- George French
- 6 years ago
- Views:
Transcription
1 PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials for use within each paint system that are compatible with one another and substrates indicated, under conditions of service and application as demonstrated by manufacturer, based on testing and field experience. b. For each coat in a paint system, provide products recommended in writing by manufacturers of topcoat for use in paint system and on substrate indicated. c. Colors: Match Columbia University's samples. Use standard, easy to replicate colors where appropriate. Custom colors will be subject to approval by CU Facilities. 2.2 Base Coats (B): a. Urethane Metal Primer: Rust-inhibitive, moisture-cured, aluminum pigmented urethane primer compatible with both conventional and catalyzed coatings, 50% (min.) solids by volume. b. Polyamide-Epoxy Primer: Two-part, polyamide-epoxy coating, 50% minimum solids by volume. c. Vinyl-Acrylic Latex Primer-Sealer: 30% minimum solids by volume. d. Alkyd Wood Primer: Interior/exterior grade alkyd undercoater, 50% minimum solids by volume. e. Latex Block Filler: One-part, vinyl-acrylic latex, 45% minimum solids by volume. f. Waterborne Polyamide Epoxy: Two-part, waterborne polyamide epoxy coating, 30% minimum solids by volume. 2.3 Latex Intermediate (I) and Top (T) Coats:
2 a. Vinyl-Acrylic Latex Flat: 35% minimum solids by volume. b. Vinyl-Acrylic Latex Eggshell: 35% minimum solids by volume. 2.4 Alkyd Intermediate (I) and Top (T) Coats: a. Modified Alkyd (One-Coat): Rust-inhibitive, self-priming, eggshell-finish spray coating, 65% minimum solids by volume. b. Alkyd Semi-Gloss Enamel: 40% minimum solids by volume. 2.5 High Performance Coatings: a. Polyamide-Epoxy: Two-part, semi-gloss, polyamide-epoxy coating, 50% minimum solids by volume. b. Polyamide-Epoxy Floor Coat: Two-part, self-priming, gloss, polyamide-epoxy coating with high resistance to water, oil, grease, chemicals, and abrasion, 60% minimum solids by volume. c. Acrylic-Epoxy Gloss: Two-part, water-based acrylic-epoxy coating, 70 to 80 (60 degree) specular gloss, 40% minimum solids by volume. d. Aliphatic Acrylic Polyurethane: Two-part, acrylic aliphatic polyurethane, 70% minimum solids by volume. e. Modified Epoxy Masonry Texture Coating: Freeze-thaw-resistant, UV-resistant, high-build dampproofing coating with sand texture finish, 50% minimum solids by volume. 2.6 Auxiliary Materials (compatible with and approved by paint coatings manufacturers), including: a. Orange Shellac: ASTM D237 Type I. b. Surfacer (Spackling Compound): Finely ground, grit-free when dry, and shall set with no shrinkage to a smooth, hard white surface that sands easily and forms a suitable substrate for required coatings. c. Barrier Coat: Type and thickness recommended for each condition by the manufacturer of coatings to be applied. It shall seal and bond to the existing coating and provide good bond for the next coating.
3 2.7.1 Submittals: Product data and samples for each product, color and texture specified. 2.8 Quality Assurance: MPI (Master Painters Institute) Standards: Comply with MPI standards and "MPI Approved Products List." CONSTRUCTION REQUIREMENTS 3.1 Examination: Examine substrates and conditions, with Applicator present, for compliance with requirements for maximum moisture content and other conditions affecting performance of work. 3.2 Maximum Moisture Content of Substrates: When measured with an electronic moisture meter as follows: a. Concrete: 12 percent. b. Masonry (Clay and CMU): 12 percent. c. Wood: 15 percent. d. Plaster: 12 percent. e. Gypsum Board: 12 percent. 3.3 Verify suitability of substrates, including surface conditions and compatibility with existing finishes and primers. 3.4 Begin coating application only after unsatisfactory conditions have been corrected and surfaces are dry. Beginning coating application constitutes Contractor's acceptance of substrates and conditions. 3.5 Preparation and Application: a. Comply with manufacturer's written instructions and recommendations in "MPI Architectural Painting Specification Manual" applicable to substrates and paint systems indicated.
4 b. Clean substrates of substances that could impair bond of paints, including dirt, oil, grease, and incompatible paints and encapsulants. Remove incompatible primers and reprime substrate with compatible primers as required to produce paint systems indicated. c. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks, roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and color breaks. d. Protect work of other trades against damage from paint application. Correct damage to work of other trades by cleaning, repairing, replacing, and refinishing, as approved by University, and leave in an undamaged condition. e. At completion of construction activities of other trades, touch up and restore damaged or defaced painted surfaces. 3.6 Interior Painting Schedule: a. EXPOSED STRUCTURAL STEEL AND GALVANIZED STEEL DECK (B) Modified Alkyd (One-Coat) 3.5 DMT. b. STEEL DOORS AND FRAMES, HANDRAILS AND GUARDRAILS (B) Urethane Metal 2.0 DMT. (I) Alkyd Semi-Gloss 2.5 DMT. (T) Alkyd Semi-Gloss 2.5 DMT. c. OTHER FERROUS METAL (B) Urethane Metal 2.0 DMT on bare surfaces. Polyamide-Epoxy 0.3 DMT on galvanized and zinc-rich primed surfaces. (I) Alkyd Semi-Gloss 2.5 DMT. (T) Alkyd Semi-Gloss 2.5 DMT Topcoat: Interior/exterior clear concrete floor sealer (water based). d. CONCRETE TRAFFIC SURFACES (B) Polyamide-Epoxy Floor 2.0 DMT. (T) Polyamide-Epoxy Floor 2.0 DMT.
5 e. CONCRETE WALLS (B) Latex 2.0 DMT. (I) Alkyd Semi-Gloss 2.0 DMT. (T) Alkyd Semi-Gloss 2.0 DMT f. MASONRY (B) Latex Block Filler at SFG. (I) Alkyd Semi-Gloss 2.0 DMT. (T) Alkyd Semi-Gloss 2.0 DMT. g. EXPOSED GALVANIZED STEEL DUCTS (B) Vinyl-Acrylic Latex 2.0 DMT. (T) Vinyl-Acrylic Latex 2.0 DMT. h. GYPSUM BOARD WALL/CEILING SURFACES: TOILET ROOMS, JANITOR'S CLOSETS (B) Vinyl-Acrylic Latex 2.0 DMT. (I) Alkyd Semi-Gloss 2.0 DMT. (T) Alkyd Semi-Gloss 2.0 DMT. i. GYPSUM BOARD WALL SURFACES: OTHER SPACES (B) Vinyl-Acrylic Latex 2.0 DMT. (I) Vinyl-Acrylic Latex 2.0 DMT. (T) Vinyl-Acrylic Latex 2.0 DMT. j. GYPSUM BOARD CEILING SURFACES: OTHER SPACES (B) Vinyl-Acrylic Latex 2.0 DMT. (I) Vinyl-Acrylic Latex 2.0 DMT. (T) Vinyl-Acrylic Latex 2.0 DMT. 3.7 Exterior Painting Schedule: a. FERROUS METAL
6 (B) Urethane Metal 2.0 DMT. (I) Polyamide-Epoxy 4.0 DMT. (T) Acrylic-Polyurethane Semi-gloss 3.0 DMT. b. GALVANIZED & NON-FERROUS METAL (B) Polyamide-Epoxy 3.0 DMT. (T) Acrylic-Polyurethane Semi-gloss 3.0 DMT. c. CONCRETE MASONRY (B) Modified Epoxy masonry Texture 8 DMT. REFERENCE 4.1 The applicable CSI Specification Section is
MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 09 - FINISHES
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Concrete. 2. Concrete
DAYTONA BEACH PIER BUILDING RESTORATION 06/10
SECTION 099113 - EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes surface preparation and the application of paint systems on the following exterior substrates: 1. Steel. 2. Galvanized
SECTION EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY
SECTION 099113- EXTERIOR PAINTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes sutface preparation and the application of paint systems on the following exterior substrates: 1. Clay masonry. 2.
Union County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 099600 - HIGH PERFORMANCE COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
A. Section includes surface preparation and the application of high-performance coating systems on the following substrates:
ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY
A. Section includes surface preparation and the application of paint systems on interior substrates.
SECTION 09 91 23 - INTERIOR PAINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
A. Section includes surface preparation and application of wood finishes[.]
![A. Section includes surface preparation and application of wood finishes[.]](/thumbs/80/81205628.jpg "A. Section includes surface preparation and application of wood finishes[.]")
SECTION 09 93 00 - STAINING AND TRANSPARENT FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
SECTION HIGH-PERFORMANCE COATINGS
SECTION 099600 - HIGH-PERFORMANCE COATINGS PART 1 - GENERAL 1.1 SUMMARY A. Section includes surface preparation and the application of high-performance coating systems on the following substrates: 1. Exterior
University of Missouri St. Louis UMSL Project No. S Thomas Jefferson Library Elevator R&B Project No: Renovation & Repairs
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
SECTION INTUMESCENT FIREPROOFING
SECTION 078123 INTUMESCENT FIREPROOFING PART 1 GENERAL 1.1 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with the requirements of the Contract Documents. 1.2
SECTION PAINTING Ultra Premium
SECTION 09 90 00 PAINTING Ultra Premium PART 3-EXECUTION 3.01 PREPARATION: A. Perform preparation and cleaning procedures in strict accordance with coating manufacturer s instructions for each substrate
UBC Technical Guidelines Section Edition Painting and Coating Page 1 of 6
Page 1 of 6 1.0 GENERAL 1.1 Related UBC Guidelines.1 Section 09 00 10 Finishes General Requirements.2 Division 27 (Section 27 05 08 Cable Infrastructure Overview, 3.4.10; Section 27 05 05 Communication
Education Facility Guide Specification
Education Facility Guide Specification This Painting Schedule is furnished as a guide to select paint systems, and is not all-inclusive of available Sherwin-Williams products. Specifiers should review
We propose to use the following Dunn-Edwards paint material on the subject job (Section 09900).
April 10, 2007 Ed Soltero AIA Assistant Director Planning & Construction 3120 Sun Bowl Drive El Paso, TX 79968 Job: UTEP Gentlemen: We propose to use the following Dunn-Edwards paint material on the subject
B. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors and finishes available for wood flooring.
SECTION 096400- WOOD FLOORING PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
SECTION PAINTING. A. Surface preparation and field application of paints and coatings at interior and exterior surfaces.
SECTION 09910 PAINTING 1 PART ONE - GENERAL 1.1 COORDINATION A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification Sections apply
UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-09 96 00 (November 2014) ----------------------------- Preparing Activity: NASA Superseding UFGS-09 96 00 (July 2007) UNIFIED FACILITIES GUIDE SPECIFICATIONS References
SECTION PAINTS AND COATINGS. 1.3 REFERENCES A. ASTM D 16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications; 2000.
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Surface preparation. B. Field application of paints, stains, varnishes, and other coatings. C. See Schedule - Surfaces to be Finished, at end of Section. 1.2 RELATED
SECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
SECTION PAINTS AND COATINGS
McClellan Blakemore Architects New Warehouse Facility for SECTION 09900 PAINTS AND COATINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Surface preparation. B. Field application of paints and stains. C. Scope:
MDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls
MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing
ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # ADDENDUM NO. 3 April 02, 2019
ZONE 7 WATER AGENCY CWS 5 TURNOUT REPLACEMENT PROJECT # 275-18 ADDENDUM NO. 3 April 02, 2019 This Addendum No. 3 ( Addendum ) is dated the date set forth above and modifies certain Bidding Documents issued
Grainger Stadium Club Building Kinston, NC Dunn & Dalton Architects Project # GRS-17048
August 31, 2017 Grainger Stadium Club Building Dunn & Dalton Architects Project # GRS-17048 RECEIPT OF THIS ADDENDUM MUST BE NOTED ON THE BID FORM ADDENDUM NO.1 TO ALL BIDDERS: This Addendum supplements
This Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces:
0 0 0 0 0 0 SECTION 0 ANTI- GRAFFITI COATINGS PART - GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division Specification
Include a paint or finish schedule on the drawings, listing colors, locations and types of materials.
DIVISION 09 - FINISHES Section 09900 - Painting Introduction This Section applies to exterior and interior areas or surfaces which are intended to receive a final field painted finish. Final painted finishes
Mold resistant, paperless gypsum board shall be used in bath, kitchen, and janitor locations.
09 00 00 - FINISHES 09 00 00 General Information CCU is continuing its investigation into preferred floor surface materials. In general, selection of floor materials should consider the environmental impact
1. Adequate framing details, sizing, spacing and technical information shall be indicated on the documents.
DIVISION 9 - FINISHES 09100 - METAL SUPPORT SYSTEMS 1. Adequate framing details, sizing, spacing and technical information shall be indicated on the documents. 2. Fire-rated assemblies and acoustic rating
UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-09 96 59 (May 2011) Change 1-08/17 -------------------------- Preparing Activity: NAVFAC Superseding UFGS-09 96 59 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
SECTION PAINT. A. Section Cast-In-Place Concrete: Preparation of concrete wall assemblies to receive finishes.
SECTION 09910 PAINT PART 1 GENERAL 1.1 SECTION INCLUDES A. Interior Primer. B. Interior Paint. C. Exterior Primer. D. Exterior Paint. E. Wall Preparation. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place
SECTION DRY ERASE COATING (IdeaPaint CREATE Black and White) A. Section Gypsum Board Assemblies; gypsum board substrate.
Guide Specifications for Designers and Specifiers: This document specifies IdeaPaint CREATE Dry Erase Coating by IdeaPaint, and is provided for your use in CSI 3-Part Format. For further assistance, call
SECTION COMMON WORK RESULTS FOR ELECTRICAL
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
SECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
INDUSTRIAL PAINTING SCHEDULE GUIDE
Copyright 2014, The Sherwin-Williams Company ISSUED May 2014 09 96 00- INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting
PART 1 - GENERAL. .2 Refer to the MPI Architectural Manual long form painting specification for guidance and spec notes when using this specification.
MPI Architectural Manual Page 1 of 15 PART 1 - GENERAL SPEC NOTES:.1 Use this guide specification when a short form specification is required to specify painting and decorating work on new, previously
Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection. NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc.
Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc. Cleaning and Protecting Concrete Surface Preparation, Application,
SECTION PAINTING
SECTION 09 91 00 PAINTING PART 1 GENERAL 1.01 SUMMARY A. Provide: 1. Paint: a. Interior Substrates: 1) Concrete masonry units. 2) Precast concrete. 3) Gypsum drywall. 4) Ferrous and zinc-coated metal.
Generic Product Index
Generic Product Index Epoxy Coatings Epoxy Tank Lining Paint High build amine adduct cured. Excellent for internal coating of storage tanks containing kerosene fuel-jp4. EC01 Special Hi-Build Epoxy Polyamine
Copyright 2014, The Sherwin-Williams Company. ISSUED June INTERIOR
Copyright 2014, The Sherwin-Williams Company ISSUED June 2014 09 91 23 - INTERIOR USGBC LEED-09 -NC/CI/CS NEW CONSTRUCTION, COMMERCIAL INTERIORS & CORE AND SHELL SPECIFICATION Contributes toward satisfying
DIVISION 9 FINISHES. This Article on Codes, Regulation and Standards shall apply to all Divisions of the Building Standards
DIVISION 9 FINISHES This Article on Codes, Regulation and Standards shall apply to all Divisions of the Building Standards 1 Table of Contents SECTION 09 05 13 COMMON FINISHES 2 SECTION 09 51 23 ACOUSTICAL
1/16 Single Broadcast Polymer Flooring System
specification 1/16 Single Broadcast Polymer Flooring System Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
The Paint the Pros Use
History Independent Tradition HEADQUARTERED IN ROCKVILLE, MD, MCCORMICK PAINTS OPERATES 24 RETAIL STORES IN THE MID-ATLANTIC REGION OF THE U.S. WITH GROWING REACH AND INFLUENCE IN ALL SEGMENTS OF ARCHITECTURAL
Coastal Carolina University Design Guidelines FINISHES
09 00 00 - FINISHES 09 00 00 General Information CCU is continuing its investigation into preferred floor surface materials. In general, selection of floor materials should consider the environmental impact
ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment
ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general
C. Surfaces to Receive Field Finishing: Areas shall be identified per project documents.
PART 1: GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Section, apply to this Section. 1.02
Gypsum Board Shaft-Wall Assemblies Gypsum board shaft-wall assembly for elevator and mechanical shafts over 2 stories.
09 00 00 - FINISHES 09 00 00 General Information Architects, in the design of project specific building systems, shall consider the unique characteristics of the generally hot-humid environment of Conway,
Copyright 2018, The Sherwin-Williams Company ISSUED MAY OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 OTC PHASE II INTERIOR HIGH PERFORMANCE COATINGS INDUSTRIAL COATINGS THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE
SECTION WOOD WINDOWS
SECTION 08 52 00 WOOD WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1.2 DEFINITIONS 1. Repair of wood window sash, frames, and sills, including repair of deteriorated wood
The City of Winnipeg NEWPCC Lab Renovation
Bid Opportunity 253-2011 Page 1 of 6 Part 1 General 1.1 SUMMARY.1 Work under this contract includes, but is not necessarily limited to:.1 Surface preparation of substrates as required for acceptance of
SECTION PAINTING
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 91 00 PAINTING SPEC WRITER NOTE: Delete between // // if not applicable to project. Delete, modify and add to text as required to suit information shown on
Section GYPSUM DRYWALL
Section 09250 GYPSUM DRYWALL 1.00 GENERAL: A. Gypsum Association Specification GA216 and manufacturer's instruction (whichever is more stringent). 2.00 DRYWALL MATERIALS: A. Exposed Gypsum Board: ASTM
SECTION PAINTING
PART 1-GENERAL 1.1 DESCRIPTION A. Section specifies field painting. SECTION 09 91 00 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project.
Copyright 2018, The Sherwin-Williams Company ISSUED MAY SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 96 00 - SCAQMD HIGH PERFORMANCE COATINGS INDUSTRIAL PAINTING THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL PAINTING SCHEDULE GUIDE This Painting
C. Samples: For each door face material, at least 3 by 5 inches (75 by 125 mm) in size, in specified finish.
SECTION 083113 - ACCESS DOORS AND FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
high-performance coatings for commercial spaces.
high-performance coatings for commercial spaces. for proven coating solutions that meet performance, aesthetic and environmental requirements just ask. matter what structure or substrate you re coating,
CUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
SECTION HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015
Specification Provided To: Date: Job: PART 1 GENERAL 1.1 SECTION INCLUDES SECTION 09 96 60 HIGH PERFORMANCE COATINGS Ramuc Type EP Epoxy Updated October 5, 2015 A. Paints and coatings of the following
CUSTOM BRICK. Custom Brick Finish Polymer System Specifications For Use On Vertical Walls DS151. Architectural Finish for Use on Vertical Walls
CUSTOM BRICK Architectural Finish for Use on Vertical Walls Custom Brick Finish Polymer System Specifications For Use On Vertical Walls PART I- GENERAL DRYVIT SYSTEMS, INC. MANUFACTURER S SPECIFICATION
Specifications. Specifications (Architectual) Metallic System. Metallic System
(Architectual) Metallic System Architectual NeverStrip Floor Coatings, 6-15 Mils Master Format Section 096700 Fluid Applied Flooring 1 of 6 NeverStrip Metallic High-Build Decorative Epoxy/Urethane Coating
Florock Seamless Flooring Systems
Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating pigmented epoxy primer, decorative pigmented
Tnemec Standard Paint Schedule
Tnemec Standard Paint Schedule PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
VengerElectrostatic Coatings Master Specification Page 1
Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits
Florock Seamless Flooring Systems
Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer, decorative pigmented epoxy coatings
SECTION EPOXY RESIN FLOORING
SECTION 09705 - EPOXY RESIN FLOORING PART 1 - GENERAL 1.1 SECTION INCLUDES A. Furnish all necessary material, labor and equipment required to prepare designated traffic areas and install quartz broadcast
Broadcast Parking Garage System
AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete
Venger Electrostatic Coatings Master Specification Page 1
Master Specification Page 1 SPEC NOTE: Update references to Division 01 General Requirements specification sections to match actual section numbers and titles used for the project. SPEC NOTE: Venger permits
SECTION MULTICOLOR INTERIOR FINISHING
SECTION 09 94 19 MULTICOLOR INTERIOR FINISHING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes:
KNOWLEDGE EXPERIENCE SERVICE /MOO BuyLine 6067
KNOWLEDGE EXPERIENCE SERVICE 09 91 00/MOO BuyLine 6067 QUALITY COATING SOLUTIONS OUTSTANDING PERFORMANCE For more than 125 years, Benjamin Moore & Co. has consistently delivered paint products that define
ARCHITECTURAL SPECIFICATION
THERMO-SORB ARCHITECTURAL SPECIFICATION PART 1 GENERAL 1.1 SECTION INCLUDES Spray applied, subliming / thin film intumescent, fire resistive coating for interior structural steel framing. Fire resistive
IFTI - Master Specification Section <IssueDate> Rev. June 2018
International Fireproof Technology, Inc. 17528 Von Karman Ave. Irvine, CA 92614 Office: 949-975-8588 IFTI SPEC NOTE: This master specification is written to include SPEC NOTES noted as IFTI Spec Note in
TT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer. A one component, alkyd base, corrosion inhibiting zinc chromate primer.
941 111313 TT-P-1757B Type I, Class C, Aerosol Zinc Chromate Primer PRODUCT: TT-P-1757B TY.I, CL.C AEROSOL ZINC CHROMATE PRIMER A one component, alkyd base, corrosion inhibiting zinc chromate primer. DESCRIPTION:
DIVISION 9 - FINISHES
09100 METAL SUPPORT SYSTEMS 09120 Ceiling Suspension Systems 09130 Wall/Partition Support Systems 09250 GYPSUM BOARD 09260 Gypsum Board Systems - Demountable 09300 TILE 09400 TERRAZZO 09500 ACOUSTICAL
A. This Section includes traffic coatings for the following applications:
SECTION 071800 - TRAFFIC COATINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes traffic coatings for the following applications: 1. Interior and exterior, pedestrian traffic. 2. Vehicular traffic.
1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
C. Wallboard shall not be glued directly to masonry or concrete walls below grade: provide furring.
09 0561 COMMON WORK RESULTS FOR FLOORING PREPARATION 09 0562 REMEDIAL FLOOR COATING 09 2116 - GYPSUM BOARD ASSEMBLIES A. Special consideration shall be given to the noise reduction characteristic and installation
SECTION (09941) - TEXTURED FINISHING
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: SECTION 09 94 13 (09941) - TEXTURED FINISHING 1. Spray Applied Textured Finish and Primer a. Textured Finish for Ceilings. b. Textured Finish for Walls.
SECTION 1045 PAINT FOR STRUCTURAL STEEL
SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Paint and Paint Material. 1045.1.1 General. All single component paints shall be ready-mixed at the factory to comply with the specification formula for the
Coating Types. Coating Systems. Coating Basics. Why coatings are used Component of coatings Methods of protection Service environment
Coating Basics Why coatings are used Component of coatings Methods of protection Service environment Coating types Curing mechanism Design characteristics Limitations Suitable Use Coating Systems Coating
Spec Master 5/7/ For each product requiring color and texture selection, provide full size samples.
SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
PIPE AND TUBE RAILINGS. Evansville Christian High School RELATED DOCUMENTS 1.1
SECTION 055213 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
Rust-Oleum. Presents. Coatings Economics 101
Rust-Oleum Presents Coatings Economics 101 It is estimated that Rust and Corrosion account for 9.5 Billion dollars in damage annually. Coatings Protect our Investment Rust What is it??? Rust or Corrosion
SECTION Arisfor WallGuard
1.1 GENERAL A. is a three component polymerized cementitious protective coating that can be applied to a variety of vertical interior and exterior substrates including: stucco, exterior gypsum sheathing,
SECTION EPOXY RESIN FLOORING
SECTION 096723 EPOXY RESIN FLOORING PART 1 GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Concrete Rehabilitation: Section 030131 B. Joint Sealants: Section 079200. 1.02 SYSTEM DESCRIPTION A. The work
Metal complies with all federal air pollution regulations for volatile organic compounds.
NOTE: For the most accurate and up-to-date information, take care to only use Guide Specifications directly from the Zolatone website. GUIDE SPECIFICATIONS SECTION 09 94 19 METAL by ZOLATONE SPECIALTY
1. Section Cast-In-Place Concrete Paragraph 3.3.A -- Delete this paragraph in its entirety.
MWA Renovation to Roundtop Building ADDENDUM NO. 1 March 28, 2018 Dunwody/Beeland, Architects, Inc. SPECIFICATIONS 1. Section 033000 Cast-In-Place Concrete Paragraph 3.3.A -- Delete this paragraph in its
DECOCOLOR FLOORING SYSTEM
AIA Specification DECOCOLOR FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions of the
ADDENDUM NO. 1 Bid # Pain ng at Perris High School, Heritage High School, and the District Administra ve Center.
ADDENDUM NO. 1 Bid #060616 Pain ng at Perris High School, Heritage High School, and the District Administra ve Center June 1, 2016 The following changes and/or addi ons to the Project Documents shall apply
SECTION PAINT, PUTTY, AND CAULKING MATERIALS FORM. Date. General Contractor. Painting Sub-Contractor. Project Number.
SECTION 09902 PAINT, PUTTY, AND CAULKING MATERIALS FORM Date General Contractor Painting Sub-Contractor Project Number Project Name Project Address 1. Paint, putty, and caulking materials as specified
SECTION RESINOUS FLOORING
SECTION 09705 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section includes all materials and installation necessary to provide resinous flooring system with integral cove base and top finish
3.3 APPLICATION INTERIOR PAINTING
NORTH BRYAN COUNTY 3-5 SCHOOL - PEMBROKE G. Shop-Primed Steel Substrates: Clean field welds, bolted connections, and abraded areas of shop paint, and paint exposed areas with the same material as used
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
Micastone Coating System
40-year R&D Experience Micastone System Multi-Colour Stone Finishing Bonntile Hong Kong Limited Flat C2, 11/F, Hang Fung Industrial Building Phase 2, 2G Hok Yuen Street, Hung Hom, Kowloon, Hong Kong (+852)
DECOFLAKE DECORATIVE FLOORING SYSTEM
AIA Specification DECOFLAKE DECORATIVE FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions
Lluminations complies with all federal air pollution regulations for volatile organic compounds.
NOTE: For the most accurate and up-to-date information, take care to only use Guide Specifications directly from the Zolatone website. GUIDE SPECIFICATIONS SECTION 09 94 19 LLUMINATIONS BY ZOLATONE SPECIALTY
Complementary Coatings Insl-x. Stix Bonding Primer Introduction
Complementary Coatings Insl-x Stix Bonding Primer Introduction Complementary Coatings: Insl-x Complementary Coatings Corporation is a wholly owned subsidiary of Benjamin Moore & Co Complete Specialty
Drawing Coordination: Show extent of surfaces to receive Polomyx Airless on the Drawings or Room Finish Schedule.
NOTE: For the most accurate and up-to-date information, take care to only use Guide Specifications directly from the Zolatone website. GUIDE SPECIFICATIONS SECTION 09 94 19 POLOMYX AIRLESS MULTICOLOR WALL
International Fireproof Technology Inc.
International Fireproof Technology Inc. The Ultimate in Firestop Solutions and Fire Protective Coatings www.painttoprotect.com 949-975-8588 Guide Specifications Alternate Thermal and Ignition Barrier IFRM
SECTION PROTECTIVE COATINGS. A. Equipment and materials which require painting or coating including but not limited to:
SECTION 09800 PART 1 - GENERAL 1.01 DESCRIPTION Painting and coating shall include all materials, labor tools, equipment and services required for the furnishing and application of all painting and coatings