ESR-2894 Reissued April 2014 This report is subject to renewal April 1, 2016.

Size: px
Start display at page:

Download "ESR-2894 Reissued April 2014 This report is subject to renewal April 1, 2016."

Transcription

1 ICC-ES Evaluation Report ESR-894 Reissued April 04 This report is subject to renewal April, 0. (800) 4-87 () A Subsidiary of the International Code Council DIVISION: THERMAL AND MOISTURE PROTECTION Section: Fiber-Cement Siding REPORT HOLDER: NICHIHA USA, INC. 9 PEACHTREE INDUSTRIAL BOULEVARD, SUITE AA NORCROSS, GEORGIA 009 (770) rhotta@nichiha.com EVALUATION SUBJECT: NICHIBOARD (ALSO KNOWN AS ECOPLANK) LAP SIDING, NICHISHAKE INDIVIDUAL SHAKES, NICHIPANEL VERTICAL SIDING AND NICHISOFFIT PANELS.0 EVALUATION SCOPE Compliance with the following codes: 009 International Building Code (IBC) 009 International Residential Code (IRC) Properties evaluated: Weather resistance Structural (transverse and racking shear loading) Surface-burning characteristics Fire-resistance-rated construction.0 USES The (also known as EcoPlank) lap siding, NichiShake individual shakes, NichiPanel vertical siding and NichiSoffit products are used as exterior wall coverings and soffits. The Nichiha products may be used on exterior walls of Types I, II, III, IV and V construction when installed in accordance with Section 40. of the IBC. The products may be used in fire-resistance-rated walls when constructed in accordance with Section DESCRIPTION. General: The products are reinforced fiber cement panels made of proprietary constituents and portland cement. The lap siding, NichiShake individual shakes and NichiPanels vertical siding comply with ASTM C 8, Type A, Grade II. The products are available in lengths, widths and thicknesses as shown in Table.. Surface-burning Characteristics and Noncombustibility: The Nichiha products exhibit a flame-spread index of or less and smoke-developed index of 40 or less when tested in accordance with ASTM E 84; and are classified as noncombustible when tested in accordance with ASTM E. 4.0 DESIGN AND INSTALLATION 4. General: Installation must comply with this report and the manufacturer s installation instructions. The manufacturer s published installation instructions and this report must be adhered to and a copy of the instructions and this report must be available at all times on the jobsite during installation. The products must be installed over wall framing and sheathing designed to resist loads in accordance with the applicable code. The wall framing and sheathing must be covered with an approved water-resistive barrier complying with IBC Section 40. and IRC Section R70. prior to installation of the Nichiha products. Fasteners used to install the Nichiha products must be corrosion-resistant and sized as specified in this report. A clear distance of inches ( mm) must be maintained between all Nichiha products and the soil on the ground. 4. Lap Siding: Lap Siding must be applied horizontally, commencing from the bottom of a wall, and with a minimum / 4 -inch-wide ( mm) overlap at the top of each panel. Vertical joints between panels must be over studs and must be staggered on subsequent courses. The vertical panel joints must be gapped / 8 inch (. mm) and filled with exterior-grade sealant conforming to ASTM C 90. A strip of flashing may be used for vertical joints. Gaps approximately / 8 inch (. mm) in width must be left at locations where the Nichiha panels butt each other, butt against the door and window trim, butt against inside corners or butt against corner trim. All gaps must be flashed in accordance with the applicable code and then must be filled with exterior-grade sealant conforming to ASTM C 90. Trim and corners must be installed as required by the Nichiha published installation instructions. Fasteners must be placed no closer than / 4 inch (9 mm) from the top edge and a minimum of / 8 inch (9. mm) from panel ends. lap siding may also be installed directly to concrete masonry blocks as set forth in Table b using / 4 -inch-long (44. mm) SurePin fasteners. Gaps approximately / 8 inch (. mm) in width must be left ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright 04 Page of 000

2 ESR-894 Most Widely Accepted and Trusted Page of at locations where the NichihBoard siding panels butt each other, butt against the door and window trim, butt against inside corners or butt against corner trim. All gaps must be flashed in accordance with the applicable code and then must be filled with exterior-grade sealant conforming to ASTM C NichiShake Siding: NichiShake individual shakes must be installed directly on 7 / -inch-thick ( mm) wood structural panels complying with U.S. DOC PS or PS. The installation must be in accordance with Nichiha s published installation instructions. NichiShakes must be blind-nailed through the preceding shake course allowing a / 4 -inch to / -inch (.4 to 8 mm) gap between shakes. NichiShakes must be staggered on subsequent courses. For horizontal joints, a minimum / 4 -inch-wide ( mm) overlap at the top of each shake is required. Fasteners must be placed no closer than / inch ( mm) to shake edges. Shake to trim joints must be gapped / 8 inch (. mm) and must be filled with exterior-grade sealant conforming to ASTM C NichiPanel Vertical Siding: The NichiPanel vertical siding must be applied with the long dimension of the panel in the vertical direction parallel to the framing. All panel edges must be backed by nominally -inch ( mm) wood or minimum No. 0 gage [0.0 inch (0.9 mm)],.-inch-by-.7-inch (9 by 4.9 mm), steel, C-shaped framing members. Gaps approximately / 8 inch (. mm) in width must be left at locations where the Nichiha panels butt each other, butt against the door and window trim, butt against inside corners or butt against corner trim. All gaps must be flashed in accordance with the applicable code and then must be filled with exterior-grade sealant conforming to ASTM C 90. Trim and corners must be installed as required by the Nichiha published installation instructions. Fasteners must be placed no closer than / 8 inch (9. mm) to panel edges. The NichiPanel vertical siding may also be installed directly to concrete masonry blocks as set forth in Table b using / 4 -inch-long (.8 mm) SurePin fasteners. Gaps approximately / 8 inch (. mm) in width must be left at locations where the Nichiha panels butt each other, butt against the door and window trim, butt against inside corners or butt against corner trim. All gaps must be flashed in accordance with the applicable code and then must be filled with exterior-grade sealant conforming to ASTM C 90, with a / 4 -inch (.4 mm) gap between flashing and next course of panels. 4. NichiSoffit Panels: The NichiSoffit panels must be attached to framing spaced a maximum of 4 inches (0 mm) on center, with the long dimension of the panel perpendicular to framing and edges supported by framing. Fasteners must be / -inch-long (8 mm), corrosion-resistant roofing nails, and their spacing must not exceed 8 inches (0 mm) on center. 4. Transverse Wind Pressures: The allowable design wind pressures for Nichiha products (based on the panel type, size, framing spacing and fastening schedule) noted in Table b must exceed the design wind pressures as noted in Table a for applicable height, wind speed, exposure and zone. The allowable fastener withdrawal capacity for the fastener, as noted in Table c (based on fastener type, penetration and wood species), must exceed the allowable fastener load in pounds per fastener specified in Table b. 4.7 Racking Shear Loads: The and NichiPanel products may be used on wood or steel framed walls as shearwalls on buildings of Type V construction and dwellings constructed in accordance with the IRC, in Seismic Design Categories A, B and C for wood framed assemblies and Seismic Design Categories A and B for steel framed assemblies. The allowable shear resistance is as set forth in Table. 4.8 One-hour Limited Load-bearing and Nonloadbearing Fire-resistance-rated Wall Assemblies: The and NichiPanel products may be used as components of one-hour fire-resistance-rated wall assemblies when constructed in accordance with Sections 4.8. through For load-bearing walls, design axial loads are based on 9-foot (.7 m) wall heights. The loadbearing wall assemblies are limited to 8 percent of the adjusted axial design loads Assembly : Limited Load-bearing Wall: Studs are nominally -by-4 wood studs, Douglas fir select structural grade spaced 4 inches (09 mm) on center with double top plates fastened to the studs using / 4 -inch-long (8. mm), No. d common nails. R glass fiber insulation is installed in the wall cavities. Type X gypsum wallboard, / 8 inch thick ( mm), is applied horizontally to both faces of the wall, and fastened to studs with / 8 -inch-thick (4. mm), No. drywall screws at 8 inches on center. Wallboard joints must be staggered from those on the opposite side. Seams in the gypsum wallboard, and fastener heads, must be treated with joint compound in accordance with ASTM C 840 or GA-. Fifteen-pound felt paper, complying with ASTM D, must be installed horizontally, with a -inch ( mm) overlap, over the fire side/interior of the wall assembly using / 4 -inch-long (. mm) staples. Twelve-inch-wide (0 mm) must be installed with a 0-inch (4 mm) exposure, horizontally on the nonfire side of the wall assembly, using No. d common nails (three nails per board at each stud) Assembly : NichiPanel Limited Load-bearing Wall: The studs are nominally -by-4 wood studs, Douglas fir select structural grade spaced 4 inches (09 mm) on center, with double top plates fastened to the studs using No. d, / 4 -inch-long (8. mm) common nails. R glass fiber insulation is installed in the cavities. Type X gypsum wallboard, / 8 inch thick ( mm), is applied horizontally to both faces of the wall, and fastened to studs with / 8 inch thick (4. mm), No. drywall screws at 8 inches (0 mm) on center. Wallboard joints must be staggered from those on the opposite side. Seams in the gypsum wallboard, and fastener heads, must be treated with joint compound in accordance with ASTM C 840 or GA-. Fifteen-pound felt paper, complying with ASTM D, must be installed horizontally, with a -inch ( mm) overlap, over the fire side of the wall assembly, using / 4 -inch-long (. mm) staples. NichiPanel must be installed vertically to the fire side/interior of the wall assembly using / 4 -inch-long (7 mm), No. 8d, common nails. The NichiPanels must be nailed at inches ( mm) on center on all panel edges and inches (0 mm) on center in the field to intermediate studs Assembly : Nonload-bearing Wall: No. 0 gage, / 8 -inch-deep-by- / -inch (9 mm by 8 mm), steel C-shaped studs are spaced at 4 inches (09 mm) on center and fastened to top and bottom tracks using / 4 -inch (9 mm), self-tapping pan head screws. R glass fiber insulation is installed in the wall cavities. Type X gypsum wallboard, / 8 inch thick ( mm), is applied

3 ESR-894 Most Widely Accepted and Trusted Page of horizontally to both faces of the wall and fastened to studs with / 8 -inch-thick (4. mm) drywall screws at 8 inches (0 mm) on center. Wallboard joints must be staggered from those on the opposite side. Seams in the gypsum wallboard, and fastener heads, must be treated with joint compound in accordance with ASTM C 840 or GA-. Fifteen-pound felt paper must be installed horizontally, with a -inch ( mm) overlap, over both sides of the wall assembly using / 4 -inch-long (. mm) staples. Twelveinch-wide (0 mm) must be installed with a 0-inch (4 mm) exposure, horizontally on the fire side and the nonfire side of the wall assembly, using / 8 -inchthick (4. mm) self-tapping screws (three screws per at each stud). The screws must be / 4 inch (9 mm) below the top edge of the lap siding at each stud location. The walls are rated for fire-resistance exposure from both sides Assembly 4: NichiPanel Nonload-bearing Wall: No. 0 gage, / 8 -inch-deep-by- / -inch (9 mm by 8 mm), steel C-shaped studs are spaced at 4 inches on center (09 mm) and fastened to top and bottom tracks using / 4 -inch (9 mm), self-tapping pan head screws. R glass fiber insulation is installed in the wall cavities. Type X gypsum wallboard is applied horizontally to both faces of the wall, and fastened to studs with / 8 -inch-thick (4. mm), No. drywall screws at 8 inches (0 mm) on center. Wallboard joints must be staggered from those on the opposite side. Seams in the gypsum wallboard, and fastener heads, must be treated with joint compound in accordance with ASTM C 840 or GA-. Fifteen-pound felt paper must be installed horizontally, with a -inch ( mm) overlap, over both sides of the wall assembly, using / 4 -inch-long (. mm) staples. NichiPanel is installed vertically on the fire side and nonfire side of the wall assembly using -inch-long ( mm) self-tapping screws. The NichiPanels must be screwed every inches ( mm) on center on all panel edges and inches (0 mm) on center in the field to intermediate studs. The walls are rated for fire-resistance exposure from both sides..0 CONDITIONS OF USE The (also known as EcoPlank) lap siding, NichiShake individual shakes, NichiPanel vertical siding and NichiSoffit products described in this report comply with, or are suitable alternatives to what is specified in, those codes listed in Section.0 of this report, subject to the following conditions:. The products are manufactured, identified and installed in accordance with this report and the manufacturer s published installation instructions. In the event of a conflict between the manufacturer s published installation instructions and this report, this report governs.. In all exterior wall applications, except for installation of the Nichiha products over 7 / -inch-thick ( mm) wood structural panels complying with U.S. DOC PS or PS, or construction in accordance with Section 4.7 of this report, the products must be installed on walls that are braced in accordance with the applicable code.. When used as shearwalls, the products are limited to racking for wind and/or Seismic Design Categories A, B or C for wood construction and A and B for steel construction, under the IBC and IRC..4 The panels are manufactured in Macon, Georgia, under a quality control program with inspections by ICC-ES..0 EVIDENCE SUBMITTED. Data in accordance with the ICC-ES Acceptance Criteria for Fiber Cement Siding Used as Exterior Wall Siding (AC90), dated October 00 (editorially revised February 0).. Data in accordance with Section 4. of the ICC-ES Acceptance Criteria for Shear Evaluation of Proprietary Sheathing Materials Attached to Lightframe Construction or Code-complying Sheathing Attached to Light-framed Walls with Proprietary Fasteners (AC9), dated October Reports of tests in accordance with ASTM E 84, ASTM E 9 and ASTM E. 7.0 IDENTIFICATION The (also known as EcoPlank) lap siding, NichiShake, NichiPanel vertical siding and NichiSoffit panels must bear a label noting the product name; the manufacturer s name (Nichiha USA, Inc.); the manufacturing plant location; and the evaluation report number (ESR-894).

4 ESR-894 Most Widely Accepted and Trusted Page 4 of TABLE NICHIHA PANEL TYPES AND DIMENSIONS PRODUCT NAME lap siding THICKNESS (inch) WIDTH (inches) LENGTH / / 4 up to feet NichiShake individual shakes / / 4 / 4 up to 8 inches NichiPanel vertical siding NichiSoffit INSTRUCTIONS FOR USE OF TABLES a, b and c / 48 8, 0 and feet / 4 up to 48 8 up to feet STEP. Utilizing the applicable wind provisions as indicated in Table a, the code-specified wind speed and the mean building roof height, determine the design wind pressure from Table a. STEP. Based on the Nichiha product type, the stud spacing, and the specified fastening schedule from Table b, determine the allowable wind pressure and the fastener load for the assembly. STEP. Compare the allowable wind pressure from Table b to the design wind pressure from Table a. If the design wind pressure from Table a is larger than the allowable deign wind pressure from Table b, choose another assembly from Table b such that allowable design pressure (from Table b) is greater than or equal to the design wind pressure from Table a. The allowable fastener withdrawal capacity for the fastener, noted in Table c (based on fastener type, penetration and framing species) must exceed the allowable fastener load in pounds per fastener specified in Table b. TABLE a DESIGN WIND PRESSURE (psf) Height Basic Wind Speed (Zone 4),, (ft) 8 mph 90 mph 00 mph 0 mph 0 mph 0 mph 40 mph 0 mph Height Basic Wind Speed (Zone ),, (ft) 8 mph 90 mph 00 mph 0 mph 0 mph 0 mph 40 mph 0 mph For SI: foot = 04.8 mm; mph =. km/h; lb/ ft = kpa. Wind Speed is Basic Wind Speed (mph) as defined in ASCE 7-0 with Exposure C and Zone 4 or as applicable as defined in ASCE 7-0 figures -A with an Effective Area of 0 square feet. Pressure is based on an enclosed structure as defined in ASCE 7-0. Per ASCE 7-0 Figure -A Zone is the end portion of the exterior wall at corners and Zone 4 is the middle portion of the wall that is not a part of Zone.

5 Siding Material NichiPanel ESR-894 Most Widely Accepted and Trusted Page of Framing Material x4 SPF Direct to Block x-/8x0 Ga Steel c-stud Fastener Type d Double HD MAZE Box Nail d Double HD MAZE Coil Nail 8d HD Siding Nail /8" Dia. Waferhead." Dia. Ribbed Buglehead SurePin Steel Pin #8A /8" Dia. Waferhead TABLE b NICHIPRODUCTS AC90 ALLOWABLE TRANSVERSE LOADS Head Dia. (in) Shank Dia. (in).0".099".8".".09".4".0"." Length (in) " / " /8 " " /4 " / " /8 " Fastening Method Face Frame Spacing / Allowable Loads (psf or lbf),,,4, " 4" Allowable Allowable Perimeter Field AC90 Allowable AC90 Allowable Pressure per Pressure per Pressure (psf) Pressure (psf) (in) (in) Fastener (lbf) Fastener (lbf) NA NA NA NA NA NA NA NA NA NA Steel Pin 0..0" / " #Z." Ga Maze x4 SPF Roofing Nail 0.." /4" Blind. 7 NA NA x4 D Fir d Double HD Face 7. 7 NA NA " " MAZE Coil Nail 7. 7 NA NA x4 SPF Ga Maze Blind 7." 0.." /4" Roofing Nail -- 0 Ga Steel Steel Pin 0.0.0" /" Face #8A Ga Maze x4 SPF 8." Roofing Nail 0.." /4" Blind 8. NA NA D Double HD x SPF " /" MAZE Nail Face NA NA " x4 D Fir " 7 40 NichiShake 9." d Double HD x4 SPF " OSB " MAZE Coil Nail " Blind OSB " 7/" OSB 9." OSB " For SI: inch =.4 mm; lb/ft = kpa; lb = 4.448N. SPF and D FIR design pressures are valid for other lumber species having assigned specific gravities of 0.4 and 0.0 or greater, respectively. This table addresses only the specified /NichiShake products and their fastening for external Component and Cladding loads. Wall stud framing must be designed to resist applicable loads. 4 Stated fastener head diameters, shank diameters, and lengths are all minimum values required to achieve tabulated loads. NA indicates the product is Not Applicable for the conditions. NichiShake allowable withdrawal fastener load is based on the OSB field fastening to the x SPF framing material. The withdrawal load of the NichiShake from the OSB has been considered and does not control.

6 ESR-894 Most Widely Accepted and Trusted Page of Fastener Type Maze HD Nail Table c ALLOWABLE FASTENER WITHDRAWAL,,,4, Specific Gravity (Material) 0.4 (SPF) Fastener Shank Diameter (in) Fastener Penetration into Material (in) Fastener Withdrawal Value (lbf) / / 4 HD Nail 0.8 / Maze HD Nail 0.4 (SPF) 0.4 (SPF) 0.09 / 0. / / / / 4 Maze HD Nail 0. (D Fir) / 8 Maze HD Nail 0. (OSB) / 7 Maze HD Nail 0.4 (SPF) 0. / 9 SurePin Direct to Block 0.4 Gripshank (#8A & #Z) / Ga steel / 8 Diameter Waferhead 0 Ga steel Specific Gravity of 0.4 is for SPF framing material. Specific Gravity of 0. is for Douglas Fir framing material (except for OSB). Wood withdrawal values based on 00 NDS equations.- &.- with CD of. for wind. 4 to steel withdrawal value based on 00 AISI Standard North American Specification for the design of Steel Structural Members equation E The allowable fastener withdrawal values specified above must be greater than or equal to the minimum fastener load specified in Table b of this report. PRODUCT NAME ( x x / ) ( x x / ) NichiPanel (4 x 8 x / ) NichiPanel (4 x 8 x / ) For SI: inch =.4 mm; plf = 4.9 N/m.,,, 4,, TABLE ALLOWABLE LOADS FOR NICHIHA PRODUCTS DESCRIPTION Nominally -by-4 wood studs, 4 inches on center. Panels face nailed to each stud with -inches-long, d common nails ( per stud). / by / 8 -inches-deep, No..0 gage, steel C-shaped studs spaced at 4 inches center. Panels fastened to each stud with / 8 -inches self-tapping screws ( per stud). Nominally -by-4 wood studs, 4 inches on center. Panels face nailed to each stud with -inches-long, d common nails ( o.c. on edge and o.c. in field). / by / 8 -inches-deep, No.0 gage, steel C-shaped studs spaced at 4 inches center. Panels fastened to each stud with / 8 -inches self-tapping screws ( o.c. on edge and o.c. in field). ALLOWABLE SHEAR RESISTANCE (plf) Shearwalls are limited to racking for wind and/or Seismic Design Categories A, B or C for wood construction and A and B for steel construction under the IBC and IRC. Wall panels were tested under wet conditioning in accordance with Section of ASTM E 7. Panel joints must occur over studs, plates or solid blocking. 4 Shearwalls have a maximum height-to-width (aspect ratio) of :., Wall studs are nominal -by-4 Spruce Pine Fir (G = 0.4) No. grade. Steel studs are No. 0 gage, / inches-by / 8 C-shaped, complying with ASTM C, with base metal thickness 0.09 inch

ICC-ES Evaluation Report Reissued March 2014 This report is subject to renewal March 1, 2015

ICC-ES Evaluation Report Reissued March 2014 This report is subject to renewal March 1, 2015 ICC-ES Evaluation Report ESR-1694 Reissued March 2014 This report is subject to renewal March 1, 201 www.icc-es.org (800) 423-687 (62) 699-043 A Subsidiary of the International Code Council DIVISION: 07

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: EVALUATION SUBJECT: STRUCTURAL PANELS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: EVALUATION SUBJECT: STRUCTURAL PANELS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2182 Reissued 08/2018 This report is subject to renewal 06/2019. DIVISION: 06 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: ENERCEPT, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: ENERCEPT, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1780 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 06 00

More information

ICC ES SYSTEM SYSTEM. Trusted DIVISION: 07 SECTION: AND FINISH REPORT HOLDER: ICC-ES Evaluation. Reissued 08/2016.

ICC ES SYSTEM SYSTEM. Trusted DIVISION: 07 SECTION: AND FINISH REPORT HOLDER: ICC-ES Evaluation. Reissued 08/2016. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 2562 Reissued 08/206 This report is subject to renewal 08/208. DIVISION: 07 00 00

More information

DIVISION: FINISHES SECTION: GYPSUM BOARD REPORT HOLDER: PANEL REY, S.A.

DIVISION: FINISHES SECTION: GYPSUM BOARD REPORT HOLDER: PANEL REY, S.A. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3831 Reissued 12/2017 This report is subject to renewal 12/2018. SECTION: 09 29 00

More information

ESR-1794* Reissued September 1, 2012 This report is subject to renewal November 1, 2014.

ESR-1794* Reissued September 1, 2012 This report is subject to renewal November 1, 2014. ICC-ES Evaluation Report www.icc-es.org (800) 4-6587 (56) 699-054 ESR-794* Reissued September, 0 This report is subject to renewal November, 04. A Subsidiary of the International Code Council DIVISION:

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: SHAKERTOWN 1992, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: SHAKERTOWN 1992, INC. 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2386 Reissued 04/2016 This report is subject to renewal 04/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: EXTERIOR INSULATION AND FINISH SYSTEMS REPORT HOLDER: PAREX USA, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: EXTERIOR INSULATION AND FINISH SYSTEMS REPORT HOLDER: PAREX USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2563 Reissued 03/17 This report is subject to renewal 03/19. DIVISION: 07 00 00 THERMAL

More information

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS, INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS, INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT: 0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 844 Valid: /3 to /5 DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION: 06 6 00 SHEATHING

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 4 6587 (562) 699 0543 www.icc es.org ESR 3152 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 07 00 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER CEMENT SIDING REPORT HOLDER: RIEDER FASERBETON ELEMENTE GmbH

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER CEMENT SIDING REPORT HOLDER: RIEDER FASERBETON ELEMENTE GmbH 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2810 Reissued 02/2018 This report is subject to renewal 07/2018. DIVISION: 07 00

More information

REPORT HOLDER: OMEGA PRODUCTS INTERNATIONAL, INC CALIFORNIA AVENUE CORONA, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: OMEGA PRODUCTS INTERNATIONAL, INC CALIFORNIA AVENUE CORONA, CALIFORNIA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-2064 Reissued 11/2017 This report is subject to renewal 11/201. DIVISION: 07 00 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: BORAL COMPOSITES, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: SIDING REPORT HOLDER: BORAL COMPOSITES, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3597 Reissued 05/2018 This report is subject to renewal 05/2019. DIVISION: 07 00

More information

REPORT HOLDER: R.L. ADAMS PLASTICS, INC CROSSROADS COMMERCE PARKWAY WYOMING, MICHIGAN EVALUATION SUBJECT: POLYCORE BRAND INSULATION

REPORT HOLDER: R.L. ADAMS PLASTICS, INC CROSSROADS COMMERCE PARKWAY WYOMING, MICHIGAN EVALUATION SUBJECT: POLYCORE BRAND INSULATION 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3914 Reissued 10/2017 This report is subject to renewal 10/2018. DIVISION: 07 00

More information

~ 100 R~~UU~]ION ~ 9RIMIOS Most Wiael>: AcceBtedana Trusted

~ 100 R~~UU~]ION ~ 9RIMIOS Most Wiael>: AcceBtedana Trusted ~ ~ 100 R~~UU~]ION ~ 9RIMIOS Most Wiael>: AcceBtedana Trusted ICC-ES Evaluation Report I (800) 423-6587 I (562) 699-0543 ESR-1668* Reissued March 1, 2009 This report is subject to re-examination in two

More information

ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years.

ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years. ICC-ES Evaluation Report ESR-2961 Reissued September 1, 2011 This report is subject to renewal in two years. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

Joint Evaluation Report ICC-ES (800) (562)

Joint Evaluation Report ICC-ES (800) (562) 0 Joint Evaluation Report ICC-ES (800) -658 (56) 699-05 www.icc-es.org 000 ESR-0 Reissued 0/0 This report is subject to renewal 0/08. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION: 06 6 00 SHEATHING

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER CEMENT SIDING REPORT HOLDER: KMEW CO., LTD. EVALUATION SUBJECT:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER CEMENT SIDING REPORT HOLDER: KMEW CO., LTD. EVALUATION SUBJECT: 0 ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org Most Widely Accepted and Trusted ESR 1627 Reissued 12/2018 This report is subject to renewal 12/2020. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: EXTERIOR INSULATION AND FINISH SYSTEMS REPORT HOLDER: DRYVIT SYSTEMS, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: EXTERIOR INSULATION AND FINISH SYSTEMS REPORT HOLDER: DRYVIT SYSTEMS, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 232 Reissued 0/207 This report is subject to renewal 0/209. DIVISION: 07 00 00 THERMAL

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: FOUR SEASONS SOLAR PRODUCTS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: FOUR SEASONS SOLAR PRODUCTS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2445 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 06 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: THERMAL INSULATION SECTION: WATER-RESISTIVE BARRIERS/WEATHER BARRIERS

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: THERMAL INSULATION SECTION: WATER-RESISTIVE BARRIERS/WEATHER BARRIERS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1504 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: GENTEK BUILDING PRODUCTS, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: GENTEK BUILDING PRODUCTS, INC. 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-1133 Reissued 11/2017 This report is subject to renewal 11/201. DIVISION: 07 00 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: TRESPA NORTH AMERICA, LTD.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: TRESPA NORTH AMERICA, LTD. 0 ICC ES Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 Most Widely Accepted and Trusted ESR 1687 Reissued 02/2016 This report is subject to renewal 02/2017. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: FUNDERMAX GMBH

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: FUNDERMAX GMBH 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3340 Reissued 05/2017 This report is subject to renewal 05/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: HY-TEK FASTENERS INC. EVALUATION SUBJECT: HY-TEK NAILS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: HY-TEK FASTENERS INC. EVALUATION SUBJECT: HY-TEK NAILS 0 ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org Most Widely Accepted and Trusted ESR-2648 Reissued 06/2018 Revised 10/24/2018 This report is subject to renewal 06/2020.

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: ASSOCIATED MATERIALS, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: ASSOCIATED MATERIALS, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1258 Reissued 03/2017 This report is subject to renewal 03/2019. DIVISION: 07 00

More information

ESR-1812 Reissued October 1, 2012 This report is subject to renewal November 1, 2013.

ESR-1812 Reissued October 1, 2012 This report is subject to renewal November 1, 2013. ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-1812 Reissued October 1, 2012 This report is subject to renewal November 1, 2013. A Subsidiary of the International Code Council

More information

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS, INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS, INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1844 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 06 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER-CEMENT SIDING REPORT HOLDER: TAKTL, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER-CEMENT SIDING REPORT HOLDER: TAKTL, LLC 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3899 Issued 04/2018 This report is subject to renewal 04/2019. DIVISION: 07 00 00

More information

REPORT HOLDER: LOUISIANA-PACIFIC CORPORATION 414 UNION STREET, SUITE 2000 NASHVILLE, TENNESSEE EVALUATION SUBJECT:

REPORT HOLDER: LOUISIANA-PACIFIC CORPORATION 414 UNION STREET, SUITE 2000 NASHVILLE, TENNESSEE EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-3090 Issued 06/2017 This report is subject to renewal 06/2019. DIVISION: 06 00 00 WOOD, PLASTICS

More information

DIVISION: FINISHES SECTION: GYPSUM BOARD ACCESSORIES REPORT HOLDER: CONLAB, INC. dba PREST ON CO.

DIVISION: FINISHES SECTION: GYPSUM BOARD ACCESSORIES REPORT HOLDER: CONLAB, INC. dba PREST ON CO. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1812 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 09 00

More information

ESR-1061 Reissued May 1, 2011 This report is subject to renewal in two years.

ESR-1061 Reissued May 1, 2011 This report is subject to renewal in two years. ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 DIVISION: 07 00 00 THERMAL AND MOISTURE PROTECTION Section: 07 21 00 Thermal Insulation Section: 07 25 00 Water-Resistive Barriers/Weather

More information

REPORT HOLDER: PAREX USA, INC EAST LA PALMA AVENUE, SUITE 250 ANAHEIM, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: PAREX USA, INC EAST LA PALMA AVENUE, SUITE 250 ANAHEIM, CALIFORNIA EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 689 Reissued 07/206 This report is subject to renewal 07/208. DIVISION: 07 00 00

More information

Joint Evaluation Report

Joint Evaluation Report 0 Joint Evaluation Report ICC ES (800) 423 6587 (562) 699 0543 www.icc es.org 000 ESR 1040 Reissued 09/2018 Revised 03/2019 This report is subject to renewal 09/2019. DIVISION: 06 00 00 WOOD, PLASTICS

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE RUBBER SHAKES REPORT HOLDER: DAVINCI ROOFSCAPES, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE RUBBER SHAKES REPORT HOLDER: DAVINCI ROOFSCAPES, LLC 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2119 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00

More information

ESR-1365 Reissued March 2014 This report is subject to renewal April 1, 2015.

ESR-1365 Reissued March 2014 This report is subject to renewal April 1, 2015. ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-1365 Reissued March 2014 This report is subject to renewal April 1, 2015. A Subsidiary of the International Code Council DIVISION:

More information

Joint Evaluation Report

Joint Evaluation Report 0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-1040 Reissued 09/2018 This report is subject to renewal 09/2019. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION:

More information

Joint Evaluation Report

Joint Evaluation Report 0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-1040 Reissued 09/2016 This report is subject to renewal 09/2018. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION:

More information

REPORT HOLDER: COREV AMERICA BRITTMOORE PARK DRIVE HOUSTON, TEXAS EVALUATION SUBJECT:

REPORT HOLDER: COREV AMERICA BRITTMOORE PARK DRIVE HOUSTON, TEXAS EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2000 Reissued 02/2017 This report is subject to renewal 02/2019. DIVISION: 07 00 00 THERMAL

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP-APPLIED WOOD COATINGS SECTION: SHEATHING REPORT HOLDER:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: SHOP-APPLIED WOOD COATINGS SECTION: SHEATHING REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1365 Reissued 04/2018 This report is subject to renewal 04/2020. DIVISION: 06 00

More information

REPORT HOLDER: THE DOW CHEMICAL COMPANY 1501 LARKIN CENTER DRIVE MIDLAND, MICHIGAN EVALUATION SUBJECT:

REPORT HOLDER: THE DOW CHEMICAL COMPANY 1501 LARKIN CENTER DRIVE MIDLAND, MICHIGAN EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3089 Reissued 07/2016 This report is subject to renewal 07/2018. DIVISION: 07 00

More information

REPORT HOLDER: GEORGIA PACIFIC GYPSUM LLC 2861 MILLER ROAD DECATUR, GEORGIA EVALUATION SUBJECT: DENSELEMENT BARRIER SYSTEM

REPORT HOLDER: GEORGIA PACIFIC GYPSUM LLC 2861 MILLER ROAD DECATUR, GEORGIA EVALUATION SUBJECT: DENSELEMENT BARRIER SYSTEM 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3786 Reissued 11/2017 This report is subject to renewal 11/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: BASF CORPORATION WALL SYSTEMS

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: BASF CORPORATION WALL SYSTEMS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2022 Reissued 04/2018 This report is subject to renewal 04/2019. DIVISION: 07 00

More information

ICC-ES Evaluation Report. ESR-3297 Reissued March 1, 2013 This report is subject to renewal May 1, 2014.

ICC-ES Evaluation Report. ESR-3297 Reissued March 1, 2013 This report is subject to renewal May 1, 2014. ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-3297 Reissued March, 203 This report is subject to renewal May, 204. A Subsidiary the International Code Council DIVISION: 07 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: PFB AMERICA CORPORATION EVALUATION SUBJECT:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: PFB AMERICA CORPORATION EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1295 Reissued 02/2019 This report is subject to renewal 02/2021. DIVISION: 06 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: ROOFING AND SIDING PANELS REPORT HOLDER: KINGSPAN INSULATED PANELS, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: ROOFING AND SIDING PANELS REPORT HOLDER: KINGSPAN INSULATED PANELS, INC. 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1143 Reissued 04/2017 This report is subject to renewal 04/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: METL SPAN, A DIVISION OF NCI GROUP, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: METL SPAN, A DIVISION OF NCI GROUP, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2218 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 07 00

More information

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT:

REPORT HOLDER: JAMES HARDIE BUILDING PRODUCTS INC ELM AVENUE FONTANA, CALIFORNIA EVALUATION SUBJECT: 0 ICC-ES Report ICC-ES (00) 423-657 (562) 6-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-220 Reissued 03/ This report is subject to renewal 03/. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: STO CORP.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: STO CORP. 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-2536 Reissued 08/2016 This report is subject to renewal 08/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: CONCRETE SECTION: INSULATING CONCRETE FORMING REPORT HOLDER: DIVERSIFOAM PRODUCTS EVALUATION SUBJECT:

DIVISION: CONCRETE SECTION: INSULATING CONCRETE FORMING REPORT HOLDER: DIVERSIFOAM PRODUCTS EVALUATION SUBJECT: 0 ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org Most Widely Accepted and Trusted ESR 1815 Reissued 10/2018 Revised 11/2018 This report is subject to renewal 10/2020.

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: ARCONIC ARCHITECTURAL PRODUCTS, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: ARCONIC ARCHITECTURAL PRODUCTS, LLC 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3435 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: MODIFIED BITUMINOUS SHEET ROOFING REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: MODIFIED BITUMINOUS SHEET ROOFING REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3909 Issued 07/2017 This report is subject to renewal 07/2018. DIVISION: 07 00 00

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: PFB AMERICA CORPORATION

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: PFB AMERICA CORPORATION 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 6587 (56) 699 05 www.icc es.org ESR 95 Reissued 0/07 This report is subject to renewal 0/09. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: PARKLEX USA

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: PARKLEX USA 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3462 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (0) 3-87 (562) 699-03 www.icc-es.org ESR-23 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00 00 THERMAL

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: PROWALL BUILDING PRODUCTS, INC.

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: PROWALL BUILDING PRODUCTS, INC. 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3720 Reissued 09/2016 This report is subject to renewal 09/2018. DIVISION: 09 00 00 FINISHES

More information

ESR-1826 Reissued May 1, 2009 This report is subject to re-examination in one year.

ESR-1826 Reissued May 1, 2009 This report is subject to re-examination in one year. ICC-ES Evaluation Report ESR-1826 Reissued May 1, 2009 This report is subject to re-examination in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: AFM CORPORATION

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: STRUCTURAL PANELS REPORT HOLDER: AFM CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2233 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 06 00

More information

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH BRAND FASTENERS

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH BRAND FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3145 Reissued 02/2017 This report is subject to renewal 02/2018. DIVISION: 05 00 00 METALS SECTION:

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: KP BUILDING PRODUCTS

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: KP BUILDING PRODUCTS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1517 Reissued 11/2016 This report is subject to renewal 11/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS SECTION: METAL WALL PANELS REPORT HOLDER: 0 Most idely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-687 (62) 699-043 www.icc-es.org ESR-199 Reissued 0/2017 This report is subject to renewal 0/2019. DIVISION: 07 00 00 THERMAL AND MOISTURE

More information

(800) (562) A Subsidiary of the International Code Council

(800) (562) A Subsidiary of the International Code Council ICC-ES Evaluation Report ESR-1479 Issued July 1, 2009 This report is subject to re-examination in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council DIVISION:

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER-CEMENT SIDING REPORT HOLDER: EQUITONE

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FIBER-CEMENT SIDING REPORT HOLDER: EQUITONE 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3910 Issued 04/2017 This report is subject to renewal 04/2018. DIVISION: 07 00 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: 3A COMPOSITES USA INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: 3A COMPOSITES USA INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1114 Reissued 09/2017 This report is subject to renewal 09/2019. DIVISION: 07 00

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: AMERICAN EAGLE MATERIALS, LLC

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: AMERICAN EAGLE MATERIALS, LLC 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2729 Reissued 04/2017 This report is subject to renewal 04/2019. DIVISION: 09 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT APPLIED FINISH SYSTEMS REPORT HOLDER: BASF CORPORATION WALL SYSTEMS

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT APPLIED FINISH SYSTEMS REPORT HOLDER: BASF CORPORATION WALL SYSTEMS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2357 Reissued 04/2018 This report is subject to renewal 04/2019. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: FCP, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL WALL PANELS REPORT HOLDER: FCP, INC. 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2937 Reissued 05/2016 This report is subject to renewal 05/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: CERTAINTEED CORPORATION

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: CERTAINTEED CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3085 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: ULTRAKOTE PRODUCTS, LLC

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: ULTRAKOTE PRODUCTS, LLC 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1471 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 09 00

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: MATERIAL DISTRIBUTOR COMPANY, INC.

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: MATERIAL DISTRIBUTOR COMPANY, INC. 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2278 Reissued 03/2018 This report is subject to renewal 03/2019. DIVISION: 09 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: ROOFING AND SIDING PANELS REPORT HOLDER: FOUR SEASONS BUILDING PRODUCTS, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: ROOFING AND SIDING PANELS REPORT HOLDER: FOUR SEASONS BUILDING PRODUCTS, LLC 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2229 Reissued 05/2018 This report is subject to renewal 05/2019. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL ROOF PANELS REPORT HOLDER: METAL SALES MANUFACTURING CORPORATION 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 3-6587 (562) 699-03 www.icc-es.org ESR-3743 Reissued 08/2017 This report is subject to renewal 08/2019. DIVISION: 07 00 00 THERMAL

More information

ICBO Evaluation Service, Inc Workman Mill Road, Whittier, California

ICBO Evaluation Service, Inc Workman Mill Road, Whittier, California Reissued June 1, 2002 ICBO Evaluation Service, Inc. 5360 Workman Mill Road, Whittier, California 90601 www.icboes.org Filing Category: DESIGN Concrete DURISOL WALL FORMS FOR CONCRETE CONSTRUCTION DURISOL

More information

REPORT HOLDER: UNITED DURALUME PRODUCTS, INC. EVALUATION SUBJECT: DURACOOL COMPOSITE STRUCTURAL INSULATED PANELS

REPORT HOLDER: UNITED DURALUME PRODUCTS, INC. EVALUATION SUBJECT: DURACOOL COMPOSITE STRUCTURAL INSULATED PANELS 0 ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org Most Widely Accepted and Trusted ESR 3779 Reissued 01/2017 Revised 10/2018 This report is subject to renewal 01/2019.

More information

ICC-ES Evaluation Report Reissued April 1, 2010 This report is subject to re-examination in two years.

ICC-ES Evaluation Report Reissued April 1, 2010 This report is subject to re-examination in two years. ICC-ES Evaluation Report ESR-2022 Reissued April 1, 2010 This report is subject to re-examination in two years. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

Product Test Summaries Nichiha Fiber Cement Products Sierra Premium Boards

Product Test Summaries Nichiha Fiber Cement Products Sierra Premium Boards Product Test Summaries Nichiha Fiber Cement Products Sierra Premium Boards Sierra Premium Certifications Test Summaries Certifications 1 ASTM C 1185 2 ASTM E 84/CAN/ULC S102-07 3 ASTM E 228 4 ASTM E 330

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: CERTAINTEED CORPORATION

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: CERTAINTEED CORPORATION 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-1066 Reissued 05/2016 This report is subject to renewal 05/2017. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2653 Reissued 09/2016 This report is subject to renewal 09/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: WATER RESISTIVE BARRIERS/WEATHER BARRIERS SECTION: AIR BARRIERS

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: WATER RESISTIVE BARRIERS/WEATHER BARRIERS SECTION: AIR BARRIERS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1993 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: PRODEMA USA INC. EVALUATION SUBJECT:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: PRODEMA USA INC. EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3439 Reissued 07/2018 This report is subject to renewal 07/2019. DIVISION: 07 00

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: SOMAR INDUSTRIES LTD LUCKETT COURT EL PASO, TEXAS 79932

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: SOMAR INDUSTRIES LTD LUCKETT COURT EL PASO, TEXAS 79932 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2732 Reissued 11/2017 This report is subject to renewal 11/2019. DIVISION: 09 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: DERBY BUILDING PRODUCTS INCORPORATED

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: DERBY BUILDING PRODUCTS INCORPORATED 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2888 Reissued 07/2017 This report is subject to renewal 07/2018. DIVISION: 07 00 00 THERMAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: COMPOSITE WALL PANELS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3704 Reissued 02/2018 This report is subject to renewal 02/2020. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: KAYCAN LTD.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: KAYCAN LTD. 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-1495 Reissued 11/2016 This report is subject to renewal 11/2018. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL SHINGLES REPORT HOLDER: TEFUTE BUILDING MATERIALS COMPANY, LLC

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: METAL SHINGLES REPORT HOLDER: TEFUTE BUILDING MATERIALS COMPANY, LLC 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4036 Reissued 05/2018 This report is subject to renewal 05/2019. DIVISION: 07 00

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: PLY GEM SIDING GROUP EVALUATION SUBJECT:

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: PLASTIC SIDING REPORT HOLDER: PLY GEM SIDING GROUP EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (00) 423-657 (562) 6-0543 www.icc-es.org ESR-1565 Reissued 07/201 This report is subject to renewal 07/201. DIVISION: 07 00 00 THERMAL

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: BOSTITCH FASTENING SYSTEMS

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: NAILS REPORT HOLDER: BOSTITCH FASTENING SYSTEMS 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2122 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 06 00 00 WOOD, PLASTICS

More information

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: BONSAL AMERICAN, INC.

DIVISION: FINISHES SECTION: PORTLAND CEMENT PLASTERING REPORT HOLDER: BONSAL AMERICAN, INC. 0 Most Widely Accepted and Trusted ICC-ES Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-2781 Reissued 02/2017 This report is subject to renewal 02/2018. DIVISION: 09 00 00 FINISHES

More information

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 3000 SERIES FASTENERS

REPORT HOLDER: AEROSMITH FASTENING SYSTEMS 5621 DIVIDEND ROAD INDIANAPOLIS, INDIANA EVALUATION SUBJECT: AEROSMITH 3000 SERIES FASTENERS 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3833 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 03 00

More information