ALUMINUM SIDING AND SOFFITS. Contact the manufacturer for testing reports referenced in this document.
|
|
- Lambert Webster
- 6 years ago
- Views:
Transcription
1 PART 1 GENERAL ALUMINUM SIDING AND SOFFITS Contact the manufacturer for testing reports referenced in this document. 1.1 SECTION INCLUDES A. Aluminum Siding. B. Aluminum Soffits. C. Aluminum trim and accessories REFERENCES A. ASTM D Practice for Determining Temperatures of Standard ASTM Molds for Test Specimens of Plastics. B. AAMA Voluntary Specification, Performance requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum Extrusions and Panels. C. AAMA Voluntary Specification, Performance requirements and Test Procedures for High Performing Organic Coatings on Aluminum Extrusions and Panels. D. AAMA Voluntary Specification, Performance requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. E. ASTM E Standard Test Method for Extended Duration Surface Burning Characteristics for Building Materials (30 min Tunnel Test). Results: Zero Flame Spread, Smoke Developed Index of 5. Meets criteria for Class A fire rating.
2 F. ASTM E136 - Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 C G. CAN/ULC S114 Standard method of test for determination of non-combustibility in building materials. 1.3 PERFORMANCE REQUIREMENTS A. Components: Design and size components to withstand dead and live loads caused by positive and negative wind pressure acting normal to plane of wall as calculated in accordance with applicable code. B. Movement: Accommodate movement within system without damage to components or movement within system; movement between system and perimeter components when subject to seasonal temperature cycling; dynamic loading and release of loads; deflection of structural support framing. C. Drainage: Provide positive drainage to exterior for moisture entering or condensation occurring within panel system. 1.4 SUBMITTALS A. Submit under provisions of Section B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Preparation instructions and recommendations. 2. Storage and handling requirements and recommendations. 3. Installation methods. C. Shop Drawings: Indicate dimensions, layout, joints, expansion joints, construction details, methods of anchorage, and interface with adjacent materials. D. LEED Submittals: Provide documentation of how the requirements of Credit will be met: In LEED v4 the use of aluminum extrusions can help buildings earn LEED points in the following categories: Materials and Resources (MR) * Environmental Product Declarations * Sourcing of Raw Materials
3 * Material Ingredients Life Cycle Assessment Report The Aluminum Association InterNACHI s Estimated Life Expectancy Chart Indoor Environmental Quality (EQ) Low-emitting materials (EQ) Decora Powder Coatings Ltd., Aluminum Powder Coatings VOC Free Certification Letter Innovation (IN) Innovation Biophilic Design: Natural Design elements help create a calming environment Easing Minds and Boosting Facade Performance Article Energy and Atmosphere (EA) Minimum Energy Performance 1. ** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected. E. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns. F. Verification Samples: For each finish product specified, two samples, minimum size 2 inches (51 mm) by 3-1/2 inches (89 mm), representing actual product, color, and gloss. G. Manufacturer's Certificates: Certify products meet or exceed specified requirements. H. Closeout Submittals: Provide manufacturer's maintenance instructions that include recommendations for periodic cleaning and maintenance of components. 1.5 QUALITY ASSURANCE A. Manufacturer Qualifications: Minimum five years experience producing aluminum finishes of the types specified and PPG, AAMA 2604 and 2605 Certified. B. Installer: Company specializing in performing Work of this section with minimum three years documented experience. C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until workmanship, color, and gloss are approved by Architect.
4 3. Refinish mock-up area as required to produce acceptable work. 1.6 DELIVERY, STORAGE, AND HANDLING A. Package and store products under cover in manufacturer's unopened packaging until ready for transport and installation. B. Protect panels from accelerated weathering by removing or venting sheet plastic shipping wrap. C. Store prefinished material off ground protected from weather, to prevent twisting, bending, or abrasion, and to provide ventilation. Slope metal sheets to ensure drainage. D. Prevent contact with materials capable of causing discoloration or staining. 1.7 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not fabricate products under environmental conditions outside manufacturer's absolute limits. 1.8 COORDINATION A. Coordinate Work with installation of windows, louvers, and adjacent components or materials. 1.9 WARRANTY A. LUXYLIFE warranty guarantees against cracking, peeling and gloss/color retention within the guidelines stated by the American Aluminum Manufactures Association (AAMA). 1. Standard Colors: a. PPG Envirocon 04- AAMA 2604 (5 Year South Florida) 15 Year manufacturer's Warranty b. PPG Coraflon - AAMA 2605 (10 Year South Florida) 20 Year manufacturer's Warranty 2. Woodgrains a. AAMA 2604 (5 Year South Florida) 15 Year manufacture's Warranty PART 2 PRODUCTS
5 2.0 MATERIAL MANUFACTURERS A. ACCEPTABLE MANUFACTURE: LUXYCLAD.., which is located at: 24 Benfield Dr, Building C, St. Catharines, ON, Canada, L2S; Tel: ; request info Web: B. ACCEPTABLE SUPPLIER: PLEASE ENTER SUPPLIER INFO C. Substitutions: Not permitted. D. Requests for substitutions will be considered in accordance with provisions of Section REQUEST FOR SUBSTITUTIONS Section A. Contracting Officer will consider requests for Substitutions only within ten (10) days after award of Contract. B. Substitutions may be considered when a Product becomes unavailable through no fault of the Contractor. C. Document each request with complete data substantiating compliance of proposed Substitution with Contract Documents: D. Substitution request documentation must include related coordination and changes made necessary by the proposed substitution. E. A request constitutes a representation that the Contractor: 1. Has investigated proposed Product and determined that it meets or exceeds the quality level of the specified Product. 2. Provide the same warranty for the Substitution as for the specified Product. 3. Coordinate installation and make changes to other Work, which may be required for the Work to be complete with no additional cost to FAA. 4. Waives claims for additional costs or time extension, which may subsequently become apparent. 5. Will reimburse Contracting Officer for review or redesign services associated with reapproval by authorities. F. Substitutions will not be considered when they are indicated or implied on shop drawing or Product data submittals, without separate written request, or when acceptance will require revision to the Contract Documents.
6 G. Substitution Submittal Procedure: 1. Submit three (3) copies of request for Substitution for consideration on Substitution Request Form attached to this Section. Limit each Substitution Request Form to one (1) proposed Substitution. 2. Provide one copy of the specified product information in addition to the proposed product s information to accommodate direct comparison(s). 3. Submit shop drawings, Product data, and certified test results attesting to the proposed Product equivalence. 4. Substitution requests must be numbered in accordance with the applicable CSI specification section. 5. The Contracting Officer will notify Contractor in writing of decision to accept or reject request. H. If request for substitution is not accepted by the Contracting Officer, Contractor is responsible for supplying item as originally specified or an acceptable substitution without additional cost to the FAA. 2.1 MATERIALS A. Extruded Aluminum Siding and Soffits: Luxyclad Wood Grain Aluminum Siding and Soffits with is extruded aluminum with integrated venting system. 1. Size: V Groove Siding & Soffit -12 pieces per box Channel Siding & Soffit - 8 pieces per box V Groove Siding & Soffit - 8 pieces per box B. Accessories: Prefinished aluminum: Provide with matching accessories and starter strips as required inch perforated vent strip 12 ft length inch V groove siding and soffit 12 ft length J track 12 ft length Inside Corner (2pc set) 12 ft length Outside Corner (2pc set) 12 ft length Starter/Finish Base & Cap (2pc set) 12 ft length
7 Base & Flat Cap (2pc set) 12 ft length Rain Screen Clip 12 ft length 2.2 FlNlSHES; Lead time varies based on colour and supply. Please check with manufacture for anticipated lead time for solid and metallic colours. A. PPG Envirocron 04 Extrusion Powder electrostatically applied Architectural Powder Coatings are approved to AAMA 2604 Performance Standard. All colours below are also available in PPG Coraflon AAMA 2605 Performance Standard. B. Gloss Level: Standard Gloss is 30 percent, plus or minus 5 percent. C. Solid Colors: 1. Bone White UC Graham White UC Bone White UC Bright White UC Colonial White UC Ivory UC Malt UC Natural Wicker UC Caramal Latte UC Sahara Sand UC Sandstone UC Beige UC Seawolf UC Antique Bronze UC Fairview Taupe UC Cocoa Bean UC105735
8 17. Medium Bronze UC Bronze UC Statuary Bronze UC Bronze UC Brick Red UC River Rouge Red UC Roasted Red Pepper UC102320XL 24. Aged Copper UC Bermuda Blue UC Fashion Gray UC Eclipse Gray UC Charcoal UC Charcoal Gray UC Black UC Platinum Mica UC106682F 32. Renaissance Silver UC106663F 33. Silver UC70470F 34. Arcadia Silver UC70123F 35. Silversmith UC70092F 36. Anodic Clear UC110423F 37. Galaxy Silver UC106683F 38. Satin Nickel UC106684F 39. Pewter UC110227F
9 40. Pewter UC70191F 41. Silver Gray UC70192F 42. Silverstorm UC106685F 43. Medium Gray UC102662F 44. Gray Velvet UC70214F 45. Cosmic Gray Mica UC106686F 46. Washington White UC70129BC 47. Manhattan Beige Pearl UC106687F 48. Sunlight Silver UC106687F 49. Moondust Mica UC106688F 50. Champagne UC70104F 51. Natural Suede Mica UC106666F 52. Champagne Bronze UC70202F 53. Cashmere Pearl UC106689F 54. Harvest Gold Pearl UC106690F 55. Driftwood Mica UC106692F 56. Lexus Bronze UC106698F 57. Bistro Bronze UC106693G 58. Dark Bronze UC70149F 59. Dark Briar Mica UC106694F 60. Café Noir Pearl UC106695F D. Super Durable Powder Coatings: The Super Durable Powder Coatings from Decoral demonstrated times the resistance to weathering as the standard powder. Premium Wood Finishes use a polyurethane powder coat with ink based wood grain patterns sublimated into the base powder effectively tattooing the powder. The combined effect
10 creates all the aesthetic aspects of real wood while offering the same environmental advantages of powder coated finishes. E. Wood Tones 1. Mahogany 2. Light Knotty Pine 3. Dark Cherry 4. Light Cherry 5. Dark Bamboo 6. Light Bamboo 7. Dark Antique Oak 8. Light Antique Oak 9. Acacia 10. Dark Fir 11. Light Fir 12. Table Walnut 13. Dark Walnut 14. Dark National Walnut Flat 15. Light National Walnut Flat 16. Dark National Walnut 17. Light National Walnut 18. Dark Knotty Pine 2.3 FABRICATION A. Prepare surfaces, pre-treat and coat components in accordance with AAMA 2604 and 2605 Quality Standards.
11 B. Wrap and package coated components using methods suitable for transit and covered site storage without damage. PART 3 EXECUTION 3.1 EXAMINATION A. Do not begin installation until colors have been verified. B. Verify framing members are ready to receive panel system. C. If preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding. 3.2 PREPARATION A. Clean surfaces thoroughly prior to installation. B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the material under the project conditions. 3.3 INSTALLATION A. Install in accordance with manufacturer's installation instructions. B. Barrier Protection: Do not install over cementitious materials, dissimilar metals or pressure treated material without adequate barrier protection. 1. Install building paper horizontally on walls to receive metal siding. 2. Weather lap edges 6 inches (150 mm) and ends minimum 6 inches (150 mm). 3. Stagger vertical joints of each layer. 4. Securely staple, nail in place. C. Fasten siding to structural supports; aligned, level, and plumb. D. Locate joints over supports. E. Install expansion control joints where indicated. F. Use concealed fasteners unless otherwise approved by Architect. G. Install soffits, and accessories in accordance with best practice, with all joint members plumb and true.
12 3.4 FIELD QUALITY CONTROL A. After installation of soffits, check entire surface for obvious flaws or defects. B. Replace and repair any problem areas, paying close attention to the substrate for causes of the problem. 3.5 CLEANING A. After application of soffits, clean as necessary to remove all fingerprints and soiled areas. B. Upon completion of soffit application, clean entire area, removing all scrap, packaging, and unused materials related to this work. 3.6 PROTECTION A. Protect installed products until completion of project. B. Touch-up, repair or replace damaged products before Substantial Completion. END OF SECTION
by Rollfab Metal Products
by Rollfab Metal Products SECTION 07460 ALUMINUM SIDING AND SOFFITS PART 1 GENERAL 1.2 RELATED SECTIONS 1.3 REFERENCES A. SECTION INCLUDES B. Aluminum Siding. C. Aluminum Soffits. D. Aluminum trim and
More information1.2.1 Section Cold-Formed Metal Framing: Metal framing for support of aluminum soffits.
1 GENERAL 1.1 SECTION INCLUDES 1.1.1.1 Aluminum Siding. 1.1.1.2 Aluminum Soffits. 1.1.1.3 Thermally Broken Façade Sub-structure. 1.1.1.4 Aluminum trim and accessories. 1.2 RELATED SECTIONS 1.2.1 Section
More informationSECTION GUTTERS AND DOWNSPOUTS
SECTION 07712 GUTTERS AND DOWNSPOUTS PART 1 GENERAL 1.1 SECTION INCLUDES A. Gutters and Downspouts. B. Related Accessories. 1.2 RELATED SECTIONS A. Section 07611 - Sheet Metal Roofing. B. Section 07220
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More informationGuideline Specifications
Page 1 of 7 PART 1 Guideline Specifications Exterior Aluminum/Composite Wall Panels GENERAL ARROWHEAD 508 SYSTEM Pressure Equalized Rainscreen SECTION 07410 1.01 SUMMARY A. Work of this section included
More informationSECTION VINYL SIDING. Copyright 2017 The Tapco Group
SECTION 07464 VINYL SIDING Copyright 2017 The Tapco Group PART 1 GENERAL 1.1 SECTION INCLUDES A. Vinyl shingle siding. B. Vinyl shake siding. C. Vinyl staggered shake siding. D. Vinyl shaped siding. E.
More informationSECTION COPPER WALL PANELS. ***This section has been updated to IBC. Verify for specific project conditions.***
***This section has been updated to IBC. Verify for specific project conditions.*** PART 1 GENERAL 1.1 SUMMARY ***Edit to project requirements*** A. Section Includes: 1. Clear copper and preweathered copper
More informationA. ASTM C190 - Test Method for Tensile Strength of Hydraulic Cement Mortars
SECTION 04850 (04 40 00) MSI PRECAST STONE VENEER SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. MSI Precast Stone Veneer for exterior and interior vertical surfaces. 1.2 RELATED SECTIONS Specifier Notes:
More informationSECTION ORNAMENTAL ALUMINUM RAILING. ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products.
SECTION 05720 ORNAMENTAL ALUMINUM RAILING ** NOTE TO SPECIFIER ** Superior Aluminum Products, Inc.; Ornamental aluminum railing products. This section is based on the products of Superior Aluminum Products,
More informationPROJECT LOCATION SECTION COPPER METAL PLATE WALL PANELS
SECTION 07 4213.25 PART 1- GENERAL 1.01 SECTION INCLUDES A. Copper metal plate wall panels. 1.02 RELATED REQUIREMENTS A. Section 05 4000 Cold-Formed Metal Framing: Wall panel substrates support framing.
More informationSpecifiers: Click on the icon in the WORD toolbar to reveal detailed instructions
Specifiers: Click on the icon in the WORD toolbar to reveal detailed instructions (Specifier Note: The purpose of this guide specification is to assist the specifier in correctly specifying perforated
More informationSECTION CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS
SECTION 08 32 20 CRL50 AND CRL51 HEAVY GLASS TOP HUNG SLIDING DOOR SYSTEMS Page 1 of 6 USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationACOUSTICAL WALL TREATMENT SECTION 09840
ACOUSTICAL WALL TREATMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: Site-fabricated, stretched fabric acoustical wall system built with rigid polymer stretching system to secure fabric over the wall
More informationPage 1 of 5
SPECIFICATIONS COMPOSITE MATERIAL PANEL SYSTEM ESTOLGA 1000 DRY SEAL SYSTEM PART 1 GENERAL 1.01 SECTION INCLUDES A. Exterior cladding consisting of formed metal composite material (MCM) sheet, secondary
More informationArchitectural Specifications, Section Phenolic Lockers
Architectural Specifications, Section 10500 Phenolic Lockers Hollman, Inc., 1825 W. Walnut Hill Lane, Irving, TX 75038, (972) 815-4000, www.hollman.com 1.0 GENERAL 1.1 SECTION INCLUDES A. Phenolic Lockers.
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationMarch 26, 2017 Page 1 PRODUCT DESCRIPTION PRODUCT FEATURES
March 26, 2017 Page 1 DESCRIPTION PRODUCT FEATURES Factory fabricated metal wall siding/cladding with related flashings and accessory components. Online brochure available at: http://www.lenmak.com BASIC
More informationSPECIFICATION SECTION PART 1 GENERAL
PART 1 GENERAL 1.01 Summary A. Furnish and install louvers, bird screens, blank-off panels, structural supports and attachment brackets as shown on the drawings, as specified, and as needed for a complete
More informationSpecifiers: Click on the icon in the WORD toolbar to reveal detailed instructions
Specifiers: Click on the icon in the WD toolbar to reveal detailed instructions (Specifier Note: The purpose of this guide specification is to assist the specifier in correctly specifying metal wall panels
More informationCorium Brick Rainscreen System Specifications
CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated
More informationPROJECT LOCATION SECTION TEXTURED METAL PLATE WALL PANELS
SECTION 07 4213.29 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Textured, aluminum metal plate wall panels. 1.02 RELATED REQUIREMENTS A. Section 05 4000 Cold-Formed Metal Framing: Wall panel substrates support
More informationSECTION DECORATIVE METAL AND GLASS RAILING
SECTION 05 73 00 DECORATIVE METAL AND GLASS RAILING PART 1 GENERAL 1.1 SUMMARY A) This section includes both standard and custom handrails as shown in the contract drawings. B) These include aluminum,
More informationSECTION TOILET COMPARTMENTS. A. Section Metal Fabrications: Concealed steel support members.
SECTION 10155 TOILET COMPARTMENTS PART 1 GENERAL 1.1 SECTION INCLUDES A. Plastic laminate partitions. 1.2 RELATED SECTIONS A. Section 05500 - Metal Fabrications: Concealed steel support members. B. Section
More informationSection Wood Grille Ceiling Panels
Section 095426 Wood Grille Ceiling Panels PART 1 GENERAL RELATED DOCUMENTS Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1 Specification sections
More informationSECTION PREFINISHED ENGINEERED WIDE-PLANK FSC OAK FLOORING
General notes to the specifier: SECTION 09 64 29 PREFINISHED ENGINEERED WIDE-PLANK FSC OAK FLOORING This is a template: edit this specification carefully to suit specific project requirements. Following
More informationSECTION COMPOSITE EXTERIOR SHUTTERS AND ACCESSORIES
SECTION 10712 COMPOSITE EXTERIOR SHUTTERS AND ACCESSORIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Functional exterior shutters. B. Exterior shutter hardware. 1.2 RELATED SECTIONS A. Section 09900 - Paints
More informationSECTION PREFINISHED FSC MAPLE FLOORING. This is a template: edit this specification carefully to suit specific project requirements.
SECTION 09 64 29 PREFINISHED FSC MAPLE FLOORING General notes to the specifier: This is a template: edit this specification carefully to suit specific project requirements. Following guidelines established
More informationSECTION PANEL AND POST AND PYLON SIGNAGE. 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Non-illuminated Panel and Post signs. 2. Internal illumination Pylon (Cabinet and Post) signs. 1.2 PERFORMANCE REQUIREMENTS A. Structural
More informationKey Features. Glass Locker Series GL5000. ¼ inch tempered glass doors with soft closing hinges. Back-painted glass can be matched to any Pantone color
Glass Locker Series GL5000 Key Features ¼ inch tempered glass doors with soft closing hinges Back-painted glass can be matched to any Pantone color Low iron glass for ultra-clear, pure colors Wood locker
More informationSECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationB. Samples for Initial Selection: For each type of impact-resistant wall protection unit indicated.
SECTION 102600 - WALL AND DOOR PROTECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPROJECT LOCATION SECTION ZINC ALLOY METAL PLATE WALL PANELS
SECTION 07 42 13.26 PART 1 - GENERAL 1.01 SECTION INCLUDES A. Zinc alloy metal plate wall panels. 1.02 RELATED REQUIREMENTS A. Section 05 4000 Cold-Formed Metal Framing: Wall panel substrates support framing.
More information1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationPRODUCT SPECIFICATIONS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below
More informationSECTION DIRECTORIES
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 13 00 DIRECTORIES SPEC WRITER NOTES: 1. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and
More informationCENTRIA FORMABOND II Metal Composite Wall System
CENTRIA FORMABOND II Metal Composite Wall System CENTRIA FormaBond II is the only true metal composite panel wall system designed, manufactured and fabricated by a single, reliable national manufacturer
More informationSL150 Guide Specification
SL150 Guide Specification This is a suggested guide specification for metal roofing projects where the SL150 panel system is applicable. Questions regarding applicability should be discussed with Union
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationSECTION Summit Phenolic Lockers (Solid Phenolic Lockers)
SECTION 10 51 00 Summit Phenolic Lockers (Solid Phenolic Lockers) Part 1-General 1.01 Summary A. Section includes: solid phenolic lockers solid phenolic benches 1.02 Submittals A. Submittals: Comply with
More informationSECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM
PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.
More information(Specifier Note: Aristech Surfaces LLC is the manufacturer of the Avonite brand
(Specifier Note: Aristech Surfaces LLC is the manufacturer of the Avonite brand The purpose of this guide specification is to assist the specifier in correctly specifying solid surface wall cladding, shower
More informationCENTRIA EcoScreen Perforated Screen Wall Panels
CENTRIA EcoScreen Perforated Screen Wall Panels CENTRIA EcoScreen Perforated Screen Wall Panels offer a variety of aesthetic solutions to equipment and other screening design requirements. EcoScreen Panels
More informationSECTION HEAVY GLASS TOP HUNG SLIDING BI-FOLD DOOR SYSTEMS
Page 1 of 6 SECTION 08 32 20 HEAVY GLASS TOP HUNG SLIDING BI-FOLD DOOR SYSTEMS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED BI-FOLD GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY,
More informationSection HIGH-TENSION Stretched-Fabric Wall Systems SoftWalls, Inc.
P a g e 1 PART I. GENERAL 1.01 Scope A. Furnish and install SoftWalls HIGH-TENSION Acoustical & Tackable Stretch Fabric Systems B. Related Work Specified Elsewhere: 1.Preparation of a smooth, flat and
More informationCENTRIA Intercept Entyre Preformed Metal Modular Panel Wall System
CENTRIA Intercept Entyre Preformed Metal Modular Panel Wall System CENTRIA Intercept Entyre is a unique modular metal wall system designed, available from a reliable national manufacturer and supported
More informationSECTION ATHLETIC AND RECREATIONAL SURFACING. A. ASTM C 67 - Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile.
SECTION 02790 ATHLETIC AND RECREATIONAL SURFACING PART 1 GENERAL 1.1 SECTION INCLUDES A. Resilient interlocking fitness flooring. 1.2 RELATED SECTIONS 1.3 REFERENCES A. ASTM C 67 - Standard Test Methods
More informationSECTION WINDOW FILM. Display hidden notes to specifier. (Don't know how? Click Here) Copyright ARCAT, Inc. - All rights reserved
SECTION 08 87 13 WINDOW FILM Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2008-2010 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Safety and Security
More informationSECTION MANUFACTURED ROOF EXPANSION JOINTS
SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS PART 1 -GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION ALUMINUM COMPOSITE MATERIAL WALL PANELS. A. Section includes aluminum composite material wall panels.
1/11 SECTION 074213.23 - ALUMINUM COMPOSITE MATERIAL WALL PANELS PART 1 - GENERAL 1.1 SUMMARY A. Section includes aluminum composite material wall panels. 1.2 PRE-INSTALLATION MEETINGS A. Pre-installation
More informationSECTION IMPACT RESISTANT WALL PROTECTION
SECTION 10265 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work under this Section shall include all materials and installation necessary to provide Impact-Resistant Wall Protection including Wall guards,
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More information1.1 SECTION INCLUDES A. Insulated Metal and FRP Wall and Ceiling Panels and Related Accessories.
Permatherm Specification SECTION 07435 (CSI MasterFormat 1995) SECTION 07 42 43 (CSI MasterFormat 2004) SECTION 07 42 13.19 (CSI MasterFormat 2012) INSULATED METAL and FRP WALL PANELS Part 1: General General:
More informationMagnum Board Section Digicon Information Inc. Page 1
Digicon Information Inc. Page 1 This section includes sheathing for exterior walls for use in a potentially damp or wet exterior cladding environment. This sheathing section forms an exterior flat plane
More informationPH6000. Key Features
Phenolic Locker Series PH6000 Key Features ½ inch doors and end panels Durable, backed by a 20 year warranty. Ideal choice for wet-use areas including pools and recreation centers Graffiti resistant, permanent
More informationSECTION METAL COMPOSITE MATERIAL WALL PANELS
SECTION 07 4264 METAL COMPOSITE MATERIAL WALL PANELS USE THIS SECTION WHEN SPECIFYING C.R. LAURENCE EWS SERIES 100 STANDARD WET SEAL FOR ALUMINUM-FACED, STAINLESS STEEL, COPPER, OR TITANIUM COMPOSITE MATERIAL
More informationSECTION WINDOW FILM. Display hidden notes to specifier. (Don't know how? Click Here) Copyright ARCAT, Inc. - All rights reserved
SECTION 08 87 13 WINDOW FILM Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2008-2010 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Safety and Security
More informationSECTION SECTIONAL OVERHEAD DOORS 522 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS. Display hidden notes to specifier. (Don't know how?
SECTION 08360 SECTIONAL OVERHEAD DOORS 522 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier. (Don't know how? Click Here) PART 1 GENERAL 1.1 SECTION INCLUDES A. Glazed Aluminum
More informationPW251 21/2 x7 GUIDE SPECIFICATION. Curtain Wall
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08900 ALUMINUM CURTAIN WALL This suggested guide specification has
More informationSection SoundPly LR M25 Acoustic Ceiling Panels
Section 095126 Acoustic Ceiling Panels PART 1 GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY A. Drawings and general conditions of the Contract, including General and Supplementary Conditions and Division 1
More informationEVO ALUMINUM COMPOSITE METAL (ACM) WALL PANEL SPECIFICATION
SECTION 07 42 43 EVO ALUMINUM COMPOSITE METAL (ACM) WALL PANEL SPECIFICATION SPEC NOTE: Optional text is indicated by square brackets []. Delete unwanted items and square brackets in final specification.
More informationSECTION FIBERGLASS REINFORCED POLYMER (FRP) PANELS
SECTION 07 44 50 FIBERGLASS REINFORCED POLYMER (FRP) PANELS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Design, Engineering, manufacturing and erection of fiberglass reinforced panels. Delegated Design of
More informationSECTION TURBINE VENTILATORS
SECTION 07 72 00 TURBINE VENTILATORS **This is a CSI Three-Part Specification using CSI MasterFormat 2004-2010 Section Numbers and Titles. This specification must be edited to suit your particular project.
More informationCENTRIA FORMABOND. Aluminum Composite Wall System
CENTRIA FORMABOND Aluminum Composite Wall System CENTRIA FormaBond is the only true aluminum composite panel wall system designed, manufactured and fabricated by a single, reliable national manufacturer
More informationGuide Specification for: FABRI TRAK PVC FREE Stretched Fabric Wall System Section [ ] or Section [ ]
Guide Specification for: FABRI TRAK PVC FREE Stretched Fabric Wall System Section [09 77 13] or Section [09 84 14] 1.0 GENERAL 1.01 Scope A. Furnish and install GeoTRAK Stretched Fabric Wall System produced
More informationSECTION RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection
SECTION 13090 RADIATION SHIELDING ENCLOSURE Low Intensity Radiation Protection Prepared by: 90 Dayton Avenue, Unit 4B, Suite 13 Passaic, NJ 07055 (973) 574-9077 13090-1 LOW INTENSITY RADIATION PROTECTION
More informationWhy Color is So Important Siding Color Things to know to make Table of Contents color work for you: Shut er Color Introduction Page 2
Table of Contents Introduction Page 2 Marketing Support Page 3 Vinyl Siding Collection Dimensions Pages 4-5 Dimensions Beaded Page 5 Progressions Pages 6-7 Evolutions Pages 8-9 Mounts Page 11-12 Vents
More informationValspar InspireME Coil and Extrusion Product Guide Specification Section Shop-Applied Coatings for Metal
When you re looking for inspiration you have a new source. valsparinspireme.com is an online experience brimming with ideas and possibilities to fuel your creativity. Valspar InspireME Coil and Extrusion
More informationLUX Specifications. Section S - Preformed Steel Siding
Part 1 General.1 System-1: Installation over building paper or air barrier membrane, on exterior grade gypsum board or exterior grade wood sheathing. 1.2 RELATED SECTIONS.1 Section 01 11 00 Summary of
More informationSECTION ENTRANCE FLOOR GRILLES STAINLESS STEEL GRATING
7160 Krick Rd., Walton Hills, OH 44146 800-321-3827 - Tel 440-439-8650 - Fax 440-439-6889 SECTION 12 48 16 ENTRANCE FLOOR GRILLES STAINLESS STEEL GRATING PART 1. GENERAL 1.01 SUMMARY: This section includes
More informationREIMAGINE METAL COLOR THAT TRANSFORMS
REIMAGINE METAL COLOR THAT TRANSFORMS TRANSFORM Your Design. Color is perception, but performance is reality. At CENTRIA, our color-matching technology has been refined for more than a century, giving
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 10505 - METAL STUDENT LOCKERS PART 1 - GENERAL 1.01 SCOPE OF WORK A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationGuide Specifications for Prodema PRODEX External Cladding
Guide Specifications for Prodema PRODEX External Cladding SECTION 07420 Exterior Wall Cladding Note: These specifications were current at the time of publication but are subject to change at any time without
More informationSIMEILINGS TORSION SPRING CEILING SYSTEM SPECIFICATION
TORSION SPRING CEILING SYSTEM SPECIFICATION NOTICE: Consult your local Sound Concepts representative or contact Sound Concepts at 204.783.6297 before specifying any optional or custom element as shape,
More informationB. Shop Drawings: For metal lockers. Include plans, elevations, sections, details, and attachments to other work.
SECTION 10 5113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSeries - 1
SECTION 08360 SECTIONAL OVERHEAD DOORS 521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationSPECIFICATIONS: Architectural Aluminum Railings
PART ONE: GENERAL 1.1 SUMMARY SPECIFICATIONS: Architectural Aluminum Railings A. Work in this section includes custom and standard Interior and Exterior aluminum railings and guardrails. 1.2 PERFORMANCE
More informationSECTION INSULATED METAL WALL PANELS. ATAS International, Inc. General Specification for Commercial/Industrial and Architectural Applications
SECTION 07 42 13 INSULATED METAL WALL PANELS ATAS International, Inc. General Specification for Commercial/Industrial and Architectural Applications PART 1 GENERAL 1.1. Summary The contract drawings indicate
More information1. Decks, balconies, and sun porches 2. Walkways, ramps, and stairways 3. Patios and courtyards
SECTION 07185 TRAFFIC MEMBRANE PART 1 GENERAL 1.1 SECTION INCLUDES A. Traffic membrane, consisting of welded seam PVC waterproofing, over f following surfaces: 1. Decks, balconies, and sun porches 2. Walkways,
More informationSECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Doors B. Track and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening in masonry.
More informationGUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM
1 GUIDE SPECIFICATION EXETER SECURITY SHIELD SECURITY WINDOW BARRIER SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials and services to furnish and install SECURITY
More informationAlply CLASSIC WALL Architectural Insulated Panel Wall System
SECTION 07 42 13 INSULATED METAL WALL PANELS ALPLY Insulated Panels Alply CLASSIC WALL Architectural Insulated Panel Wall System PART 1 / GENERAL 1.1 SYSTEM DESCRIPTION A. Smooth, non-embossed steel, insulated
More informationProduct Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
More informationGuide Specifications Section
Guide Specifications Section 08 87 13 SOLAR CONTROL FILMS LLumar Reflective Series Note: Click on Show/Hide button to reveal "Specifier Notes" throughout section. Delete this text when editing is complete.
More informationPERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960
STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary
More informationLouis Armstrong New Orleans International Airport NOAB Project # North Terminal Development Program Phase 1
Louis Armstrong New Orleans International Airport NOAB Project # 8910-01233 PART 1 - GENERAL SECTION 07 71 29 - MANUFACTURED ROOF EXPANSION JOINTS 1.1 RELATED DOCUMENTS A. Drawings and general provisions
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More informationSOLAR SHADING SYSTEMS - Manual Solar Shade SECTION ROLLER WINDOW SHADES
PART 1 - GENERAL SECTION 122413 - ROLLER WINDOW SHADES 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationE. Section Polymer Modified Cement Waterproofing. K. Section Sub drainage: Foundation perimeter drainage.
DELTA -DRAIN Section 07 10 00 Dampproofing and Waterproofing PART 1 GENERAL 1.1 SECTION INCLUDES A. Below grade drainage sheets. B. Plaza deck and planter drainage sheets. 1.2 RELATED SECTIONS A. Section
More informationSECTION Structured Polycarbonate Panel Assemblies. Series 3500 BPC System with 40mm Tongue and Groove
Duo-Gard Industries Inc. 40442 Koppernick Road Canton, Michigan 48187 Phone (734) 207-9700 Fax (734) 207-7995 www.duo-gard.com SECTION 08 45 13 Structured Polycarbonate Panel Assemblies Series 3500 BPC
More informationAcoustic Ceiling Products (ACP) Fasäde Thermoplastic Panels Section Digicon Information Inc. Page 1
Digicon Information Inc. Page 1 This section includes PVC ceiling panels for surface mounting or t-bar grid, and accessories. Panels are non-fire rated. This section includes proprietary and descriptive
More informationSPECIFICATION SECTION 05515: LADDERS O Keeffe s Aluminum Ladders
Welcome to the O Keeffe s Guide Specification System prepared as an aid to specify in preparing written construction documents. For specification assistance with specific product applications, please contact
More informationGLASS WALL SPECIFICATIONS
GLASS WALL SPECIFICATIONS PRODUCT OVERVIEW: Top Supported Center Stack Paired Panels Manually Operated Maximum Opening Height: 10'2 [3.1] Maximum Opening Width: Unlimited Select for Special Needs: Use
More informationSECTION ALUMINUM COMPOSITE WALL PANEL SYSTEM
SECTION ALUMINUM COMPOSITE WALL PANEL SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Includes drawings and provisions of the General Conditions, Supplementary Conditions and the sections included under
More informationSECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL PART 1.1 SECTION INCLUDES A. Overhead doors. B. Bi-fold doors. PART 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete: Prepared opening
More informationWe love architecture.
We love architecture. IMAGINE LONGBOARD table of contents Longboard Product Summary 4 5 6+7 8+9 10+11 Quality You Can Trust Longboard Cladding System Longboard Back Framing System Longboard Privacy Screen
More informationUniversity Apartments on Brooklyn PROJECT MANUAL
Section 122100 Horizontal Louver Blinds University Apartments on Brooklyn PART 1 - GENERAL 1.1 SECTION INCLUDES A. Horizontal slat louver blinds. B. Operating hardware. 1.2 RELATED SECTIONS A. Section
More informationSECTION WINDOW FILM. A. Section Windows; windows to receive architectural window film.
SECTION 08870 WINDOW FILM PART 1 GENERAL 1.1 SECTION INCLUDES A. Safety and security films. 1.2 RELATED SECTIONS A. Section 08500 - Windows; windows to receive architectural window film. B. Section 08600
More informationSECTION CRC575 UNITARY CLEANROOM WALL SYSTEM STUDLESS CLEANROOMWALL SYSTEM ME175 3-IN-1 CLEANROOM WALL SYSTEM
SECTION 13200 CRC575 UNITARY CLEANROOM WALL SYSTEM 175-300 STUDLESS CLEANROOMWALL SYSTEM ME175 3-IN-1 CLEANROOM WALL SYSTEM PART 1 GENERAL 1.01 WORK INCLUDED A. This Section provides the requirements necessary
More informationINFINITY MAX TILE SPECIFICATION
www.infinityperformance.com 888-479-1017 INFINITY MAX TILE SPECIFICATION Physical Specification: INFINITY MAX configurations consist of an interlocking, dual durometer flooring system consisting of a high
More information