A. Testing Laboratory Services: Section B. Excavation, Site Fill and Rough Grading: Section Sub-Base Course Material (If requested).
|
|
- Gerard Gyles Fleming
- 6 years ago
- Views:
Transcription
1 SECTION PART 1 - GENERAL 1.01 RELATED WORK SPECIFIED ELSEWHERE A. Testing Laboratory Services: Section B. Excavation, Site Fill and Rough Grading: Section C. Concrete: Section SUBMITTALS A. Samples: 1. Sub-Base Course Material (If requested). B. Product Data: PART 2 - PRODUCTS 1. Pavement Sealer, including application instructions. 2. Expansion Joint Filler. 3. Expansion Joint Sealant. 4. Pavement Marking Paint BITUMINOUS MATERIALS A. Sub-Base Course - Run-Of-Crusher Stone: 1. Conform with NYSDOT Section Type Material shall be stone or blast furnace slag. (Open hearth slag or sand and gravel will not be accepted.) percent passing 2 inch sieve, percent passing 1\4 inch sieve, 5-40 percent passing No. 40 sieve, 0-10 percent passing No. 200 sieve. B. Asphalt Top Course - Vehicular: 1. Binder: NYSDOT Section Binder Type 3 (Item ). 2. Topping: NYSDOT Section Type 7 Top (Item )
2 C. Tack Coat: NYSDOT Asphalt Emulsion (HFMS-2h) D. Bituminous Pavement Sealer: 1. Acceptable Products: a. Sealtight Driveway Sealer by W. R. Meadows, Inc. b. Playtime Pavement Sealer by Playtime U.S.A., Inc. c. Jennite J-16 by Maintenance, Inc. 2. Material: a. A coal tar emulsion material specifically formulated to seal asphalt concrete pavement. b. Add four pounds of sand per gallon of undiluted pavement sealer and mix to a uniform consistency. c. Sand: Clean, hard, and durable, free from clay, salt and organic matter, and well graded within the following limits: U.S. Sieve Total % Passing No % No to 100% No to 90% No to 60% No to 5% d. Dilute sealer with potable water in accordance with the manufacturer's recommendations CONCRETE PAVEMENT AND CURB MATERIALS A. Sub-Base Course - Run-Of Crusher Stone: 1. Conform with NYSDOT Type Material shall be stone or blast furnace slag. (Open hearth slag or sand and gravel will not be accepted.) percent passing 2 inch sieve, percent passing 1/4 inch sieve, 5-40 percent passing No. 40 sieve, 0-10 percent passing No. 200 sieve
3 B. Concrete: Class A, 4000 psi (Refer to Section 03310) C. Reinforcement: (As specified in Section 03310) D. Expansion Joint Filler: 1. Material: a. Fiber expansion joint, ASTM D1751. b. 1/2" thick, unless otherwise indicated. 2. Acceptable Products: a. Fibre Expansion Joint by W. R. Meadows, Inc. b. Flexcell by The Celotex Corp. c. Accepted equal E. Expansion Board and Cap & Pull Off Top: 1. Greenstreak Removable Top-Expansion Joint Cap #941, # Vinylex Corp. Removable Cap Strip Vp 1391, VP Accepted equal. F. Doweled Joint Material: 1. 3/4" x 1'-4" smooth dowels with dowel caps equivalent to No. 87 by Heckman Building Products, Inc. 2. Grease end of dowel prior to installing cap. G. Expansion Joint Sealant: 1. Material: a. Two component Polyurethane Sealant, self-leveling. b. ASTM TT-S-00227E or TT-S-00230C Type 1, Class A
4 2. Acceptable Products: a. Pourthane by W. R. Meadows, Inc. b. THC-900 by Tremco Manufacturing Company. c. Accepted equal. H. Concrete Curb Expansion Joint Sealant: 1. Material: a. Multi-Component Urethane Sealant. b. Federal Specification TT-S-00227E, Type II, Class A. 2. Acceptable Products: a. Dymeric by Tremco Manufacturing Company. b. Sonolastic NP II by Sonneborn Building Products. I. Expansion Joint Backer Rod: 1. Acceptable Products: a. Sonoforam by Sonneborn Building Products. b. Ethafoam by Dow Chemical Company. c. Sealtight Backer Rod by W. R. Meadows, Inc. d. Accepted equal. 2. Size: To allow 30% compression when inserted in joint PAVEMENT MARKING PAINT A. Acceptable Products: 1. Traffic Marking Paint by Sherwin Williams. 2. Hi-High Plexicolor Line Paint by California Products Corp. B. Color: White, Yellow, Blue
5 PART 3 - EXECUTION 3.01 SUBGRADE PREPARATION UNDER PAVEMENT Fine grade and proof roll all areas in accordance with NYSDOT Specifications BITUMINOUS A. All Courses: 1. Roll each course with 10 ton roller or equivalent. 2. Commence rolling along lower edge and continue until edge is thoroughly compacted, after which gradually advance to the crown. 3. Continue rolling until the layer has become thoroughly compacted and is true to grade and cross section. B. Sub-Base Course: 1. Place on dry subgrade in maximum lifts of 6". 2. Remove subgrade material, which becomes mixed with base course and reconstruct. 3. Minimum Compaction: 95% of maximum density. 4. Grade Tolerance: Plus or minus 3/8" from indicated grades. C. Asphalt Top Course: 1. Do not install asphalt paving over wet base course or if ambient temperature is below 50 degrees F. 2. Place in two courses to compacted thickness as detailed. 3. Where pavement abuts curbs, concrete walks, or existing pavement, apply a liberal application of tack coat material. 4. Check with 10' straight edge and correct all depressions and high areas greater than 1/4". 5. Form or cut all pavement edges to clean, sharp lines or radius, as indicated. 6. Compaction for wearing course shall be minimum of 92% of Laboratory Specimen density
6 3.03 PAVEMENT SEALER A. Allow pavement to weather a minimum of four weeks prior to sealing. B. Clean surface of dirt and other foreign matter. C. Apply two coats of sealer uniformly at a minimum total coverage of 0.18 gallons per square yard per coat. D. Required for all parking areas and lots. (Not on roadways) E. Allow a minimum of 24 hours for curing prior to checking sealed pavement for vehicle usage PAVEMENT MARKING A. Apply one coat of pavement marking paint where indicated. B. Apply by brush or zone marking equipment CONCRETE - VEHICULAR A. Sub-Base Course: 1. Place on dry subgrade in maximum lifts of 6" and compact with a 10 ton roller or equivalent. 2. Commence rolling along lower edge and continue until edge is thoroughly compacted, after which gradually advance to the crown. 3. Continue rolling until the layer has become thoroughly compacted and is true to grade and cross section. 4. Remove subgrade material, which becomes mixed with base course and reconstruct. 5. Minimum Compaction: 95% of maximum density. 6. Grade Tolerance: Plus or minus 3/8" from indicated grades. B. Concrete Reinforcement: 1. 6 x 6 - W2.9 x W2.9 unless other size is indicated. 2. Top of slab to reinforcement: 1/3 slab depth. 3. Place reinforcement in accordance with Section
7 C. Concrete: 1. Place, cure and protect in accordance with Section Finish: Screed to grade, wood float and give a final fine broom finish. Edge all sides. D. Expansion Joints: 1. Install expansion joint filler where concrete pavement abuts building foundations, steps, other concrete structures and elsewhere where indicated. 2. Remove perforated cap from premold filler. 3. Install backer rod to uniform depth to allow application of sealant to depth recommended by the manufacturer for indicated joint width. 4. Apply manufacturers recommended primer and fill joint with expansion joint sealant. E. Dowelled Expansion Joint: After concrete has cured, remove strip from premolded joint filler and fill joint with sealant flush with concrete CONCRETE - SIDEWALKS A. Sub-Base Course: 1. Place on dry subgrade and compact with a 10 ton roller or equivalent. Continue rolling until course is thoroughly compacted and true to grade and cross section. 2. Remove subgrade material, which becomes mixed with base course and reconstruct. 3. Minimum Compaction: 95% of maximum density. 4. Grade Tolerance: Plus or minus 1/4" from indicated grades. B. Concrete Reinforcement: 1. 6 x 6 - W1.4 x W1.4 unless other size is indicated. 2. Top of slab to reinforcement: 1/3 slab depth
8 3. Place reinforcement in accordance with Section C. Concrete: 1. Place, cure and protect in accordance with Section Finish: Screed to grade, wood float and give a fine broom finish. D. Expansion Joints: 1. Install expansion joint filler: a. Where concrete walks abut building foundations, perpendicular curbs, steps or concrete structures. b. Across walks at maximum intervals of 30 linear feet. c. Other locations indicated on the drawings. 2. Remove perforated strip-off cap from premolded joint filler. 3. Apply manufacturer's recommended primer and fill joint with expansion joint sealant. E. Scored Joints: 3.07 CONCRETE CURBS 1. Use tool, which produces a "V" joint 1/2" depth and not over 1/4" wide. 2. Locate joints across walks at intervals of 5'-0", unless otherwise indicated. 3. Walks wider than 5 feet: Provide 5'-0" square pattern, unless otherwise indicated. A. Reinforcement: One No. 5 bar top and bottom, except provide smooth doweled slip joint at expansion joints. B. Concrete: 1. Place, cure and protect in accordance with Section Uniform smooth finish on all exposed surfaces
9 C. Expansion Joints: 1. Construct expansion joints at maximum intervals of 30 feet and at beginning and end of radius. 2. Install expansion joint filler to within approximately 3/4" of surface of concrete. 3. Install backer rod to uniform depth to allow application of sealant to depth recommended by the manufacturer for indicated joint width. 4. Apply primer, if recommended by the manufacturer, and fill joint with concrete curb expansion joint sealant. Tool slightly concave. END OF SECTION
ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS
ITEM 6 CONCRETE CURBS, GUTTERS, AND SIDEWALKS 6.1 DESCRIPTION This work shall consist of constructing curbs, gutters, sidewalks, ramps, local depressions and driveways of the form and dimensions shown
More informationSECTION BITUMINOUS CONCRETE PAVEMENT
SECTION 321216 BITUMINOUS CONCRETE PAVEMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationA. Texas Department of Transportation 2004 Standard Specifications for Construction and Maintenance of Highways, Streets and Bridges (TxDOT).
SECTION 32 01 16 ASPHALT OVERLAY PART 1 - GENERAL 1.1 SCOPE OF WORK A. This Section specifies the requirements for scarifying, grinding, sweeping and repair of existing asphalt concrete pavement to establish
More informationPERMEABLE INTERLOCKING PAVERS
PERMEABLE INTERLOCKING PAVERS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Subgrade Preparation B. Placement of Storage Aggregate C. Placement of Filter Aggregate D. Placement of Bedding Course E. Placement
More informationITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED)
ITEM 275 PORTLAND CEMENT TREATED MATERIALS (ROAD MIXED) 275.1. Description. This Item shall govern for treating subgrade, new and/or existing base [with or without asphaltic concrete pavement (ACP)], or
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES
More informationDIVISION 32 EXTERIOR IMPROVMENTS
DIVISION 32 EXTERIOR IMPROVMENTS DIVISION 32 EXTERIOR IMPROVEMENTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationAsphalt Rubber Chip Sealing DRAFT MAINTENANCE SPECIFICATION. March 22, 2007
Asphalt Rubber Chip Sealing DRAFT MAINTENANCE SPECIFICATION March 22, 2007 Description: This work consists of furnishing and applying asphalt rubber binder followed by an application of treated cover aggregate
More informationCITY OF FARGO SPECIFICATIONS CONCRETE SIDEWALKS AND DRIVEWAYS
CONCRETE SIDEWALKS AND DRIVEWAYS PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of all labor, material, and equipment necessary
More informationMunicipality of Waterville Public Sidewalk Repair Policy
Municipality of Waterville Public Sidewalk Repair Policy Purpose - The purpose of this policy is to protect the public health, safety and welfare of the citizens and inhabitants of the Municipality by
More informationITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT
9/30/2009 AC 150/5370-10E ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 631-1.1 GENERAL. This item shall consist of a mixture of refined coal tar emulsion, mineral
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationBIO-AQUIFER STORM SYSTEM
BIO-AQUIFER STORM SYSTEM Specifications for Construction PART 1 GENERAL 1.01 SECTION INCLUDES A. Providing labor, materials, tools and equipment to furnish and install a permeable concrete paving stone
More informationSECTION CAST-IN-PLACE CONCRETE
SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. The Contractor shall furnish all work and materials, including cement, sand and coarse aggregate, water, admixtures, curing
More informationDESIGN STANDARDS. Division 02 Existing Conditions- Site Work. General
DESIGN STANDARDS Division 02 Existing Conditions- Site Work General I. This Division includes: A. Demolition B. Clearing and Grubbing C. Excavation, Backfill and Compaction D. Pavement Base E. Paving and
More informationMaintenance & Rehabilitation. Treatments. Crack Sealing. Sealant Types. Asphalt Pavement Preservation: Identification of Alternative Treatments
Asphalt Pavement Preservation: Evaluation, Maintenance & Rehabilitation Maintenance & Rehabilitation Treatments Identification of Alternative Treatments Before selecting a treatment for a pavement, we
More informationExtraction and Sieve Analysis ( µm minus) Forming Marshall Specimens, Field Method
3.56 COLD IN-PLACE RECYCLING 3.56.1 GENERAL This specification covers the requirements for Cold In-Place Recycling (CIR) which consists of reclaiming the existing asphalt pavement; sizing the reclaimed
More informationSECTION 402 PLANT MIX BITUMINOUS SURFACE LEVELING
SECTION 402 PLANT MIX BITUMINOUS SURFACE LEVELING 402.1 Description. This work shall consist of placing, spreading and compacting a bituminous mixture as shown on the plans or as directed by the engineer.
More informationA. Texas Department Transportation 2004 Standard Specifications for Construction of Highways, Streets and Bridges (TxDOT):
SECTION 31 32 13.16 CEMENT STABILIZATION PART 1 GENERAL 1.1 SCOPE OF WORK A. This Section pertains to the specifications for cement stabilization of sandy or silty soil and consists of pulverizing, addition
More informationGUIDE SPECIFICATION FOR MULTI-PURPOSE EXPANSION/CONTRACTION JOINT FILLER: NOMAFLEX
GUIDE SPECIFICATION FOR MULTI-PURPOSE EXPANSION/CONTRACTION JOINT FILLER: NOMAFLEX SECTION 03 15 00 CONCRETE ACCESSORIES EXPANSION/CONTRACTION JOINT FILLER Specifier Notes: This guide specification is
More informationSECTION 26 - COLD PLANE ASPHALT CONCRETE PAVEMENT TABLE OF CONTENTS
SECTION 26 - COLD PLANE ASPHALT CONCRETE PAVEMENT TABLE OF CONTENTS Section Page 26-1 GENERAL... 26.1 26-2 PAVEMENT KEYCUTTING... 26.1 26-3 PAVEMENT PLANING... 26.2 26-4 PLANED PAVEMENT CONFORMS... 26.3
More informationCONSTRUCTION SPECIFICATION FOR CONCRETE CROSSWALK INDEX TS SCOPE...3
CITY OF TORONTO TS 3.65 TRANSPORTATION SERVICES STANDARD CONSTRUCTION SPECIFICATIONS June 2001 CONSTRUCTION SPECIFICATION FOR CONCRETE CROSSWALK INDEX TS 3.65.01 SCOPE...3 TS 3.65.02 TS 3.65.03 REFERENCES...3
More informationSECTION 20 INDEX PAVING FABRIC 1. SCOPE OF WORK MATERIAL REQUIREMENTS CONSTRUCTION AND INSTALLATION REQUIREMENTS...
SECTION 20 INDEX PAVING FABRIC 1. SCOPE OF WORK... 20-2 2. MATERIAL REQUIREMENTS... 20-2 3. CONSTRUCTION AND INSTALLATION REQUIREMENTS... 20-2 4. METHOD OF MEASUREMENT... 20-5 20-1 SECTION 20 PAVING FABRIC
More informationProudly Made in the U.S.A.
5-Year Warranty Proudly Made in the U.S.A. Cast-In-Place (wet-set) 2 Cast-In-Place (wet-set) Tactile Proudly Made in the U.S.A. In stock colors White 37875 Brick Red 20109 Yellow 33538 Blue 15187 Safety
More informationHITT STREET UNIVERSITY PROJECT #: CP REFER TO CP PLANS FOR ELECTRICAL DUCTBANK IN HITT STREET INSTALL:
N 1133521.33 E 1689742.43 STA: 10+53.07 INSTALL: 2-10" 90 BENDS CONNECT TO MIDDLEBUSH HALL INTERIOR PLANT PLUMBING MIDDLEBUSH HALL HW1 HWS HWR 10+00 FREDRICK APARTMENTS FINE ARTS INSTALL 422 LF 10" HWS
More information550 Surface Treatments
Table of Contents 550 Surface Treatments... 550-1 550.1 Introduction... 550-1 551 Crack Sealing... 550-1 551.1 Project Selection... 550-1 551.2 Design Considerations... 550-1 552 Chip Sealing... 550-2
More informationSECTION SITE CONCRETE
SECTION 321313 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationA Design Review of Waterproofing Codes
A Design Review of Waterproofing Codes Section 1807 of Chapter 18 of the International Building Code addresses waterproofing under the section title of Dampproofing and Waterproofing. The section defines
More informationSECTION EPOXY TERRAZZO
SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationCRUSHED AGGREGATE BLENDED WITH GRANITECRETE ADMIXTURE SURFACING
Guide Specification CRUSHED AGGREGATE BLENDED WITH GRANITECRETE ADMIXTURE SURFACING COORDINATE WITH DRAWINGS: Show location and extent of stabilized aggregate surfacing. Show details required at adjoining
More informationFLUID APPLIED WATERPROOFING
SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.
More informationSection 504. MICRO-SURFACING
504.01 Section 504. MICRO-SURFACING 504.01. Description. This work consists of preparing existing pavement and providing and placing a micro-surfacing mixture. 504.02. Materials. Provide materials in accordance
More information4-07 Asphalt Treated Permeable Base (ATPB)
1 1 0 1 0 1 Supplement Division with the following: (November 0,, APWA GSP) -0 Asphalt Treated Permeable Base (ATPB) -0.1 Description Asphalt treated permeable base (ATPB) consists of a compacted course
More informationSECTION CONCRETE PAVING SLABS SET IN MORTAR
SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints
More informationSECTION HYDRAULIC CEMENT UNDERLAYMENT
ARDEX GUIDE SPECIFICATION ARDEX Underlayment HC 100 High-Capacity Self-Leveling and V1200 Self-Leveling Flooring Underlayment Cement-based Self-Leveling Underlayment for use with ARDEX ARDIFLO System SECTION
More informationCement Stabilized Soil (CSS) (Portland cement)
Cement Stabilized Soil (CSS) (Portland cement) 1.0 DESCRIPTION. This specification shall govern the process known as Cement Stabilized Soil (CSS). CSS consists of mixing the existing base, subbase and
More informationSPECIFICATIONS FOR STREET CONSTRUCTION WITHIN THE TOWN OF PLAINVILLE
SPECIFICATIONS FOR STREET CONSTRUCTION WITHIN THE TOWN OF PLAINVILLE BE IT ORDAINED by the Town Council of the Town of Plainville: SECTION 1. SUBDIVISIONS. All subdivisions hereinafter developed within
More informationCURB & GUTTER, DRIVEWAYS & SIDEWALKS
02400 Concrete Curb & Gutter, Driveways, Sidewalks, and Other Miscellaneous Concrete Page 02400-1 (Last Revised 6/22/10) 02400 - CURB & GUTTER, DRIVEWAYS & SIDEWALKS SELECTED LINKS TO SECTIONS WITHIN THIS
More information1. Division 09 Section "Rough Carpentry."
GREENSPOINT AND LAUDER RD. EC/PRE-KlK PAGE 1 SECTION 096400 - WOOD FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More informationSACRAMENTO COUNTY ASPHALT RUBBER HOT MIX-GAP GRADED (ARHM-GG):
SACRAMENTO COUNTY ASPHALT RUBBER HOT MIX-GAP GRADED (ARHM-GG): ARHM-GG shall conform to the provisions for Type "A" asphalt concrete in Section 39, "Asphalt Concrete," of the State Standard Specifications
More informationVIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LATEX MODIFIED EMULSION TREATMENT (MICRO-SURFACING)
S312EM2-1110 VIRGINIA DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LATEX MODIFIED EMULSION TREATMENT (MICRO-SURFACING) August 10, 2010 I. DESCRIPTION This work shall include furnishing and placing
More informationSPECIFICATIONS FOR SAND SEAL
SPECIFICATIONS FOR SAND SEAL 1.0 DEFINITIONS The term Director [Superintendent, etc.] shall mean the Director of Public Works of the awarding authority. The term Designee shall mean an employee of the
More informationPAVING SLABS ON A CONCRETE BASE
SECTION 32 14 13.16 PAVING SLABS ON A CONCRETE BASE (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs on a sand bed over concrete for pedestrian applications.
More informationSECTION EPOXY FLOORING SYSTEMS
SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationApplication Specification:
Application Specification: GW-15-UBU-HD April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR VEHICULAR TRAFFIC DECKS AND RAMPS
More informationCHARACTERISTICS CSA A TECHO-BLOC Compressive strength psi [45 MPa] min.
PATIOS, WALKWAYS, POOLSIDES & STEPPING STONES PHYSICAL AND GEOMETRICAL CHARACTERISTICS CHARACTERISTICS CSA A231.1 2 TECHO-BLOC Compressive strength - 6 500 psi [45 MPa] min. Flexural strength 650 psi [4.5
More informationSECTION INTERLOCKING CONCRETE PAVERS
SECTION 23 14 13 INTERLOCKING CONCRETE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for concrete paver applications in the U.S. for concrete pavers and bedding sand over a compacted
More informationSECTION PERMEABLE INTERLOCKING CONCRETE UNIT PAVEMENT
SECTION 32 14 13 19 PERMEABLE INTERLOCKING CONCRETE UNIT PAVEMENT SECTION 32 14 13 19 PERMEABLE INTERLOCKING CONCRETE UNIT PAVEMENT PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Permeable Articulating
More informationE.V.A. EXPANSION JOINT SYSTEMS
E.V.A. EXPANSION JOINT SYSTEMS A PERMANENT, WATERTIGHT SYSTEM INTRODUCTION Thermal-Chem E.V.A. is an expanded, closedcell, cross-linked, pre-formed expansion joint system manufactured from ethylene vinyl
More informationSection 25 Aggregate Subbase
Black text from standard FAA spec Strikeout text deletions from FAA standard spec Blue text additions to FAA standard spec Red text notes to the Engineer/won t appear in spec I. DESCRIPTION A. GRANULAR
More informationMay 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building
May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING
More informationINDUSTRY RECOMMENDATION EXTERIOR CONCRETE FLATWORK
INDUSTRY RECOMMENDATION for EXTERIOR CONCRETE FLATWORK Prepared by Ohio Concrete Inquires regarding this document may be addressed to: Ohio Concrete 2600 Corporate Exchange Dr., Ste. 165 Columbus, OH 43231
More information1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.
WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3
More informationREQUEST FOR PROPOSAL Asphalt & Concrete Repair
REQUEST FOR PROPOSAL 2017 Asphalt & Concrete Repair English Landing Elementary School Union Chapel Elementary School Lakeview Middle School Park Hill High School Prairie Point Elementary School Congress
More informationA. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.
SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSidewalk Replacement Criteria The following are the criteria used to determine if sidewalk needs to be replaced in the City of Watertown:
Sidewalk Replacement Criteria The following are the criteria used to determine if sidewalk needs to be replaced in the City of Watertown: -Any slab raised one-half inch (1/2 ) or more, which is considered
More informationITEM 340 DENSE-GRADED HOT-MIX ASPHALT (METHOD)
ITEM 340 DENSE-GRADED HOT-MIX ASPHALT (METHOD) 340.1. Description. Construct a pavement layer composed of a compacted, dense-graded mixture of aggregate and asphalt binder mixed hot in a mixing plant.
More informationSECTION COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING
P.O. Box 599 - Mars, PA 16046 800-321-3337 SECTION 07555 COLD APPLIED RUBBER MODIFIED ASPHALT WATERPROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including
More informationA. General: Refer to and comply with Division 1 Section Submittal Procedures, for procedures and other submittal criteria.
SECTION 02790 POURED RUBBER PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationMANUFACTURER'S SPECIFICATIONS Section ST. ASTIER LIME PLASTER (NHL) PLASTER ON CONCRETE
MANUFACTURER'S SPECIFICATIONS Section 09225 ST. ASTIER LIME PLASTER (NHL) PLASTER ON CONCRETE ST. ASTIER NATURAL HYDRAULIC LIME PLASTER PART 1 GENERAL 1.1 Summary A. This Section includes St. Astier Natural
More informationHARD COURT/RUNNING TRACK CONSTRUCTION. A. Section Includes: Tennis courts, basketball/volleyball courts, and running tracks.
PART 1 GENERAL 1.01 SUMMARY SECTION 02545 HARD COURT/RUNNING TRACK CONSTRUCTION A. Section Includes: Tennis courts, basketball/volleyball courts, and running tracks. B. Related Sections: 1. 02200 - Earthwork.
More informationITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS
ITEM D-701 PIPE FOR STORM DRAINS AND CULVERTS 701-1 DESCRIPTION 701-1.1 This item shall consist of the construction of pipe culverts, and storm drains, removal of existing storm pipes, connections to existing
More informationQUALITY COATING & REPAIR PRODUCTS
2011 Agricultural Product Catalog QUALITY COATING & REPAIR PRODUCTS Roof & Foundation Barn & Fence Driveway Concrete The Farm Pride Seal of Approval signifies a dedicated commitment to product quality
More informationSample Specification
Sample Specification Section 02760 Paving Specialties StencilCoat Commercial Asphalt and Concrete Surfacing System 1.0 GENERAL 1.1 Summary The StencilCoat Commercial Asphalt Surfacing System is a 100%
More informationSpecial Provision for Hot-Mix Asphalt Prime Coat
All Regional Engineers Omer M. Osman, P.E. Special Provision for Hot-Mix Asphalt Prime Coat July 25, 2014 This special provision was developed by the Bureau of Materials and Physical Research to improve
More informationWarm Mix Asphalt (WMA) Guide Specification for Highway Construction
Warm Mix Asphalt (WMA) Guide Specification for Highway Construction Division 400 - Asphalt Pavements and Surface Treatments SECTION 4XX - WARM MIX ASPHALT (WMA) PAVEMENT Warm mix asphalt (WMA) is the generic
More informationARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound
ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE
More information*************************************************************************************************************************
SECTION 02545 HARD COURT & RUNNING TRACK CONSTRUCTION ************************************************************************************************************************* SPECIFIER: CSI MasterFormat
More informationLEGACY REPORT DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: FLUID APPLIED ROOFING REPORT HOLDER: METACRYLICS
0 Most Widely Accepted and Trusted ICC ES Legacy Report ICC ES 000 (800) 6587 (56) 699 05 www.icc es.org ER 785 Reissued 09/017 This report is subject to renewal 09/0. DIVISION: 07 00 00THERMAL AND MOISTURE
More informationSPECIFICATIONS FOR CAST-IN-PLACE CONCRETE SLAB DUNN COUNTY TRANSFER STATION MENOMONIE, WISCONSIN
SPECIFICATIONS FOR CAST-IN-PLACE CONCRETE SLAB DUNN COUNTY TRANSFER STATION MENOMONIE, WISCONSIN 1. SUMMARY A. Work includes: 1. Pavement removal, topsoil stripping, and site grading for concrete slab.
More informationNarrow Modular Pavers (NMP) for Sand-Set Installations
The following specification refers to the Stepstone, Inc. product known as: Narrow Modular Pavers (NMP) for Sand-Set Installations Narrow Modular Pavers are part of the California Architectural Paver line
More informationSECTION 107 JOINT FILLER AND SEALANTS
SECTION 107 JOINT FILLER AND SEALANTS 107.1 GENERAL This section specifies the joint fillers and sealants that are applicable to concrete pavements, concrete channel linings, sidewalks, driveways, and
More informationPERMEABLE PAVERS PHYSICAL AND GEOMETRICAL CHARACTERISTICS - PAVERS DRIVEWAYS, PERMEABLE DRIVEWAYS & PATIOS CHARACTERISTICS CSA A231.
DRIVEWAYS, DRIVEWAYS & PATIOS PHYSICAL AND GEOMETRICAL CHARACTERISTICS - CHARACTERISTICS CSA A231.2 TECHO-BLOC Compressive strength 50 MPa [7200 psi] min. 50 MPa [7200 psi] min. Absorption - 5 % max. Freeze-thaw
More informationLong County Middle & Walker Elementary Phase I Grading
SECTION 32 1216 BITUMINOUS CONCRETE PAVEMENT (SUPERPAVE) PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-32 12 21 (August 2008) --------------------------- Preparing Activity: USACE Superseding UFGS-32 12 21 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS References
More informationSECTION WOOD AND ATHLETIC FLOORING. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 096466 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationSECTION TRENCHING & BACKFILLING
SECTION 02225 - TRENCHING & BACKFILLING 1.0 GENERAL 1.1 Work included in this Section includes trenching and backfilling for underground pipelines and related structures only. 1.2 Reference Specifications
More informationThe Work under this Section consists of performing all operations necessary to complete construction of the leveling course on the prepared subbase.
SECTION 20.22 LEVELING COURSE Article 22.1 General The Work under this Section consists of performing all operations necessary to complete construction of the leveling course on the prepared subbase. Article
More informationTotTurf TPV (1-4mm) Product Specification
TotTurf TPV (1-4mm) Product Specification PART 1 GENERAL 1.01 POURED IN PLACE PLAYGROUND SURFACING TotTurf TPV poured in place rubber playground surfacing shall consist of a polyurethane binder mixed with
More informationTEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING
SECTION 09960 - TEXTURED COATINGS Coating System Submittals Guide Specification TEX COTE 600 TEXTURED COATING MASONRY PROTECTIVE COATING (SPLIT FACE OR SAND FINISH BLOCK) 1. TEX COTE 600, Textured Coating
More informationSPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 5/8/7)
Page 1 of 7 STONE STRONG SYSTEMS SPECIFICATIONS FOR PRECAST MODULAR BLOCK RETAINING WALL SYSTEM (revised 5/8/7) PART 1: GENERAL 1.01 Description A. Work includes furnishing and installing precast modular
More informationLS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION
LS 2519 CONCRETE PAVER PAVEMENT RECONSTRUCTION A. Section Includes B. References C. Quality Assurance D. Submittals E. Delivery, Storage and Handling F. Environmental Conditions G. Summary H. Concrete
More informationSECTION 6.0 CONCRETE AND ASPHALT CONSTRUCTION FOR CURB AND GUTTER, DRIVEWAYS AND SIDEWALKS
SECTION 6.0 CONCRETE AND ASPHALT CONSTRUCTION FOR CURB AND GUTTER, DRIVEWAYS AND SIDEWALKS 6.01 Description These specifications shall include concrete and asphalt curb and gutter, driveway and sidewalk
More informationfor Mortar-Set Concrete Tiling Installations
The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural
More informationVulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS
Vulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS 1. Purpose 1.1 The purpose of this document is to establish uniform procedures for applying the Vulkem Extreme Wearing System (EWS).
More informationCITY OF FARGO SPECIFICATIONS AGGREGATE BASES
AGGREGATE BASES PART 1 DESCRIPTION OF WORK The work to be done under this section of the Specifications and the accompanying plans consists of all labor, material, accessories, and equipment necessary
More informationSECTION REINFORCING STEEL
SECTION REINFORCING STEEL 1. DESCRIPTION This specification shall govern the furnishing and placing of reinforcing steel, deformed and smooth, of the size and quantity designated on the plans and in accordance
More informationPARKING LOT AND ROADWAY MAINTENANCE
Village of Vernon Hills Community Development Engineering Division Phone 847-367-3704 Fax 847-367-2541 PERMIT APPLICATION PROCESS PARKING LOT AND ROADWAY MAINTENANCE Removal and replacement, concrete and
More informationSECTION JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 07-9200 - JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationBituminous Concrete Base Course (Type HB, Black Base, B-25.0, and B-37.5)
SECTION 5.0 BITUMINOUS CONCRETE PAVEMENT 5.01 Description (a) Bituminous Concrete Base Course (Type HB, Black Base, B-25.0, and B-37.5) This item shall consist of a base course composed of a mixture of
More informationAsphalt Guidelines. Courtney Rousseau, P.E. Lloyd Consulting Group, LLC
Asphalt Guidelines Courtney Rousseau, P.E. Lloyd Consulting Group, LLC Objectives Review typical asphalt sections and other key components to ensure optimal material usage for your project Review hot mix
More informationBID # REPAIR AREA OF PARKING LOT DAMAGED BY WATER LINE LEAK SECTION C TECHNICAL SPECIFICATIONS OWNER
BID # 14-47 REPAIR AREA OF PARKING LOT DAMAGED BY WATER LINE LEAK SECTION C TECHNICAL SPECIFICATIONS OWNER Board of Trustees Middlesex County College 2600 Woodbridge Avenue P.O. Box 3050 Edison, New Jersey
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationEditing notes to assist users are separated from specification text by rows of asterisks. Delete these notes prior to final printing.
SECTION 09635 LIMESTONE FLOORING This guide specification has been prepared by TexaStone Quarries LLC to assist design professionals in the preparation of a specification section covering cut limestone
More informationTotTurf EPDM Product Specification
TotTurf EPDM Product Specification PART 1 GENERAL 1.01 POURED IN PLACE PLAYGROUND SURFACING TotTurf EPDM poured in place rubber playground surfacing shall consist of a polyurethane binder mixed with 100%
More informationUNHSC Bioretention Soil Specification February, SOIL PREPARATION (PERFORMANCE SPECIFICATION) for Bioretention Systems
SOIL PREPARATION (PERFORMANCE SPECIFICATION) for Bioretention Systems PART 1 - GENERAL 1.1 SUMMARY A. Section includes soil media for the bioretention systems and rain gardens specified according to performance
More informationITEM 25 CHIP SEAL MATERIALS 2 A. Non-Polymer Modified Asphalt Emulsion (Fog Seal) 2 B. Polymer Modified Asphalt Emulsion Binder 2
ITEM 25 CHIP SEAL 25.1 DESCRIPTION 2 25.2 MATERIALS 2 A. Non-Polymer Modified Asphalt Emulsion (Fog Seal) 2 B. Polymer Modified Asphalt Emulsion Binder 2 25.3 AGGREGATES 3 25.4 MIX DESIGN 4 25.5 EQUIPMENT
More informationSECTION CERAMIC TILING
SECTION 09 3013 CERAMIC TILING PART 1 - GENERAL 1.1 SUMMARY A. Includes But Not Limited To: 1. Furnish and install ceramic tile and tile setting materials and accessories as described in Contract Documents.
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING
More informationKOSTER AMERICAN CORPORATION
Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General
More information