INSTALLATION SYSTEMS FOR FLOORING PROFESSIONALS. High-quality products Progressive ideas Great service

Transcription

1 INSTALLATION SYSTEMS FOR FLOORING PROFESSIONALS High-quality products Progressive ideas Great service

2 ADVANCEMENT THROUGH INNOVATION Chembond holds to this fundamental philosophy to meet the demands of the flooring industry, both now and into the future. Along with product development, this innovation applies to everything we do from technical support to customer service and communication. Since 1977, Chembond has served as a pillar of the Canadian flooringinstallation industry by offering innovative, dependable, user-friendly installation products at affordable prices. Beginning operations in Toronto, Chembond has taken product performance, breadth of offerings and branding to new levels while offering the industry top-notch value and customer support. Continuing on its path of continual improvement, Chembond will further this trend of innovation by advancing the products and technology needed to install the tile and stone of tomorrow. TABLE OF CONTENTS SURFACE PREPARATION 2 Chempatch 2101 WALL-BASE ADHESIVE 2 BaseBond 1651 TILE AND STONE INSTALLATION MORTARS 3 ScratchBond FloorBond MagniFlex MagniFlex Super MagniFlex Ultimate MagniFlex QS 8860 ADDITIVE 5 Chemlastic 7400 CERAMIC TILE ADHESIVE 6 TileGrab I 1640

3 SURFACE PREPARATION Chempatch 2101 Rapid-Set Cement Patch Chempatch 2101 is a rapid-setting, polymer-modifi ed, cementbased fl oor-patching compound. When mixed with water, it can smooth, level and patch imperfections in concrete and approved wood underlayments prior to fl oor-covering installation. The ultimate fl oor preparation product for performance and versatility Dries fast to an ultra smooth fi nish Self-cures to a compressive strength greater than 27,6 MPa (4,000 psi) Final set Drying time before installing fl oor covering Up to 10 minutes Up to 40 minutes 60 to 90 minutes Approximate (per 10-kg [22-lb.] bag) 3 mm (1/8") thickness 2,60 m² (28 ft.²) Bag,10 kg (22 lbs.) Product Code * Pot life may vary due to amount of material mixed, temperature of substrate, room and water used in the mix. For more information, see individual Product Data Sheet and Chembond s Substrate Requirements for Floor Coverings document. The most recent information can be found at Set time shown is based on 23 C (73 F) at 50% relative humidity. Actual times may vary depending on the size, ambient and substrate temperatures, and humidity levels. WALL-BASE ADHESIVE BaseBond 1651 Supreme Wall-Base Adhesive BaseBond 1651 is a premium acrylic-based adhesive for the installation of most types of wall bases. BaseBond 1651 is part of the EcoTech family of adhesives, which are solvent-free, low-tvoc, low-odour and nonfl ammable for safer installation. Will not stain wall base Great initial grab and long-term bond strength Thick viscosity for excellent trowelability For interior installation of vinyl, rubber and carpet types of wall bases Open time Cartridge, 850 ml (28.7 U. S. oz.) Bucket, 9,46 L (2.5 U.S. gals.) Up to 30 minutes Product Code Product Code Standard Trowel and Approximate based on 3,79 L (1 U.S. gal.) Standard Trowel Flooring Type Size Wall base 3 x 3 mm (1/8" x 1/8"), saw-tooth 85 linear m (280 linear ft.) Open time may vary due to substrate porosity, humidity levels and amount of adhesive applied. For more information, see individual Product Data Sheets and Chembond s Substrate Requirements for Floor Coverings document. The most recent information can be found at 2

4 TILE AND STONE INSTALLATION MORTARS ScratchBond 8200 Scratchcoat Mortar for Metal Lath ScratchBond 8200 is a Portland-cement-based scratchcoat mortar for use with metal lath on plywood subfloors and countertops prior to setting ceramic tile and stone. Use it with metal lath fastened to exterior-grade plywood to create a semi-floating underlayment system, reducing the potential for in-plane cracking of installed ceramic or stone. Economical Portland-cement-based Apply to metal lath that is attached to exterior-grade plywood. Doing so creates a semi-floating underlayment system that reduces the potential for in-plane cracking of installed ceramic tile or stone. Install ceramic tile later over the installation of metal lath and ScratchBond For residential and commercial interior floors and countertops Approved substrate: Exterior-grade plywood (on interior residential floors and countertops only) About 2-1/2 hours Initial set (before applying tile 24 hours mortar) Bag, 22,7 kg (50 lbs.) Product Code FloorBond 8400 Dry-Set Floor Tile Mortar FloorBond 8400 is a single-component, Portland-cement mortar for installing lowabsorption ceramic floor tile, quarry tile and pavers. An economical, floor tile mortar Portland-cement-based Mix with water (or undiluted Chemlastic 7400 for increased performance). For residential interior/exterior floors and commercial interior countertops Approved substrates (when mixed with water): Interior residential concrete floors, concrete mortars and concrete leveling coats Approved substrates (when mixed with undiluted Chemlastic 7400): Interior/exterior residential concrete floors, concrete mortars and concrete leveling coats Exterior residential floor tile installation on concrete floors For setting vitreous and impervious floor tiles on interior cement backer units (CBUs) or interior/exterior concrete Exterior-grade plywood installed on interior floors and countertops in residential, dry areas only About 4 hours Open time* 15 to 30 minutes Initial set (before grouting) Final set (before general foot traffic) Bag, 22,7 kg (50 lbs.) 48 hours after installation 72 hours after installation Product Code Meets or exceeds ANSI A118.1 standards when mixed with water and ANSI A118.4 standards when mixed with undiluted Chemlastic 7400 MagniFlex 8810 Floor and Wall Tile Mortar MagniFlex 8810 is a single-component, polymer-modified, dry-set mortar for installing vitreous (low-absorption) porcelain, ceramic, paver and quarry tiles as well as traditional nonvitreous tiles. Dry-set mortar For residential/commercial interior floors, walls and countertops Approved substrates: Interior residential and commercial concrete floors, as well as walls and countertops made of cement backer units (CBUs), in dry areas About 4 hours Open time* 15 minutes Initial set (before grouting) 16 to 24 hours Final set (before general foot traffic) Bag, 22,7 kg (50 lbs.) 24 to 36 hours after installation Product Code Meets ANSI A118.1 standards when mixed with water Standard Trowels and Approximate based on 22,7 kg (50 lbs.) Standard Product Trowel Size FloorBond 8400 Magniflex x 6 x 6 mm (1/4 x 1/4 x 1/4 ), squarenotch 6 x 6 x 6 mm (1/4 x 1/4 x 1/4 ), squarenotch 6,97 to 8,36 m² (75 to 90 ft.²) 6,97 to 8,36 m² (75 to 90 ft.²) * Pot life and open time may vary due to amount of material mixed, as well as temperature of substrate, room and water used in the mix. Set times shown are based on 23 C (73 F) at 50% relative humidity. Actual times may vary depending on the size, ambient and substrate temperatures, and humidity levels. For more information, see individual Product Data Sheets and Chembond s Substrate Requirements for Tile document. The most recent information can be found at 3

5 TILE AND STONE INSTALLATION MORTARS MagniFlex Super 8820 Polymer-Modified Floor and Wall Tile Mortar MagniFlex Super 8820 is an economical polymer-modified dry-set mortar for setting tile and stone. Excellent bond capacity For setting dimensional stone as well as ceramic, porcelain and quarry tile For residential (interior floors, countertops and walls; and exterior floors and walls) and commercial (interior floors and walls; and exterior floors) Approved substrates: Fully cured concrete, concrete mortars and concrete leveling coats Masonry block Exterior-grade plywood (interior floors only) Gypsum wallboard (interior walls only) Cement backer units (CBUs), interior applications only Properly prepared unglazed tile, cement terrazzo, vinyl composition tile (VCT), vinyl asbestos tile (VAT) and cutback adhesive residue MagniFlex Ultimate 8830 High-Performance, Polymer-Modified Floor and Wall Tile Mortar MagniFlex Ultimate 8830 is a high-performance, polymer-modified, single-component, thin-set mortar for setting ceramic tile and dimension stone. Enhanced and polymer-modified For setting dimensional stone as well as ceramic, porcelain and quarry tile About 1-1/2 to 2 hours For setting floor and wall tile For residential (interior floors, countertops and walls; and exterior floors and walls) and commercial (interior floors and walls; and exterior floors) Approved substrates: F ully cured concrete, concrete mortars and concrete leveling coats Masonry block Exterior-grade plywood (interior floors only) Gypsum wallboard (interior walls only) Cement backer units (CBUs), interior applications only I nterior properly prepared unglazed tile, cement terrazzo, vinyl composition tile (VCT), vinyl asbestos tile (VAT) and cutback adhesive residue Initial set (before grouting) 16 to 24 hours Final set (before general foot traffic) s 72 hours after installation About 2 hours Initial set (before grouting) ; white Final set (before general foot traffic) Bag, 22,7 kg (50 lbs.), grey Product Code Bag, 22,7 kg (50 lbs.), white Product Code to 24 hours 72 hours after installation Bag, 22,7 kg (50 lbs.), grey Meets or exceeds ANSI A118.4 and ANSI A standards Product Code Meets or exceeds ANSI A118.4 and ANSI A standards Standard Trowels and Approximate based on 22,7 kg (50 lbs.) Product Standard Trowel Size 6 x 6 x 6 mm (1/4" x 1/4" x 1/4"), square 6,97 to 8,36 m² (75 to 90 ft.²) Magniflex Ultimate 6 x 6 x 6 mm (1/4" x /4" x 1/4"), square 6,97 to 8,36 m² (75 to 90 ft.²) MagniFlex Super 8820 * P ot life may vary due to amount of material mixed, as well as temperature of substrate, room and water used in the mix. et times shown are based on 23 C (73 F) at 50% relative humidity. Actual times may vary S depending on the size, ambient and substrate temperatures, and humidity levels. For more information, see individual Product Data Sheets and Chembond s Substrate Requirements for Tile document. The most recent information can be found at 4

6 TILE AND STONE INSTALLATION MORTARS MagniFlex QS 8860 High-Performance, Polymer-Modified, Quick-Set Floor and Wall Tile Mortar MagniFlex QS 8860 is a single-component, high-performance, polymer-modified quick-set mortar for installing ceramic tile and dimensional stone. Quick-set Polymer-modified For fast tiling of floors and walls that must be ready for use in a short time (such as in supermarkets, hospitals, airports and shopping malls) For installing vitreous, semivitreous and nonvitreous ceramic tile and impervious ceramic mosaics on residential interior floors, walls and countertops; residential exterior floors and walls; and commercial interior floors and walls For residential (interior floors, countertops and walls; and exterior floors and walls) and commercial (interior floors and walls; and exterior floors) Approved substrates: Fully cured concrete Concrete block and masonry block Exterior-grade plywood (interior floors and countertops only) Cement backer units (interior applications only) Interior properly prepared unglazed tile, old cement terrazzo floors, vinyl composition tile (VCT), vinyl asbestos tile (VAT), cutback adhesive residue, plastic laminate countertops and noncushioned sheet vinyl Initial set (before grouting) Final set (before general foot traffic) About 30 minutes About 70 minutes About 90 minutes ADDITIVE Chemlastic 7400 Latex Additive for Dry-Set Mortar Chemlastic 7400 is an acrylic latex additive that forms high-strength bonds to ceramic tiles when mixed with factory-prepared dry-set mortars such as FloorBond Develops high-strength bond between tile and substrate Improves freeze/thaw resistance between tile and substrate Mix only with factory-prepared dry-set mortars. when mixed undiluted with FloorBond 8400 For residential interior/exterior floor and countertops in dry areas only For installing ceramic, porcelain, mosaic, glass and quarry tiles; pavers; slate; marble; and granite Approved substrates: Fully cured concrete (at least 28 days old) Cement backer units (CBUs) (interior only) Concrete mortars and concrete leveling coats Masonry block (floors only) when mixed with FloorBond 8400 About 4 hours Initial set (before grouting) 48 hours Final set (before general foot traffic) 72 hours after installation White Pail, 7,57 L (2 U.S. gals.), white Product Code Meets or exceeds ANSI A118.4 standards when mixed with FloorBond 8400 Bag, 22,7 kg (50 lbs.), grey Product Code Meets or exceeds ANSI A118.4 and ANSI A standards Standard Trowels and Approximate based on 22,7 kg (50 lbs.) Standard Trowel Product Size MagniFlex QS x 6 x 6 mm (1/4" x 1/4" x 1/4"), square 6,50 to 8,36 m² (70 to 90 ft.²) * Pot life may vary due to amount of material mixed, as well as temperature of substrate, room and water used in the mix. Set times shown are based on 23 C (73 F) at 50% relative humidity. Actual times may vary depending on the size, ambient and substrate temperatures, and humidity levels. For more information, see individual Product Data Sheets and Chembond s Substrate Requirements for Tile document. The most recent information can be found at 5

7 CERAMIC TILE ADHESIVE TileGrab I 1640 Type 1 Floor and Wall Tile Adhesive TileGrab I 1640 is a Type 1, high-performance, multipurpose, nonfl ammable, ceramic fl oor and wall tile adhesive. It is used for installing ceramic, porcelain, mosaic and quarry tiles. Ready to use (no mixing required) Easy to spread Quick-grab, nonslip Minimal odour Water cleanup For residential interior fl oors, walls and countertops in light-duty applications For residential interior wet walls (shower; tub and bath surrounds) where service requirements do not exceed ANSI A136.1 standards Approved interior substrates: Gypsum wallboard (walls only) Fully cured concrete walls (at least 28 days old) Masonry block walls Cement backer units (CBUs) APA or COFI Group 1 exterior-grade plywood (residential fl oors and countertops in dry areas) Open time Initial set (before grouting) Final set (before general foot traffi c) About 40 to 55 minutes 24 to 48 hours 72 hours after installation White Pail, 3,79 L (1 U.S. gal.), white Product Code Pail, 13,2 L (3.5 U.S. gals.), white Product Code Pail, 18,9 L (5 U.S. gals.), white Product Code Standard Trowel and Approximate based on 3,79 L (1 U.S. gal.) Standard Trowel Product Size TileGrab I x 6 x 6 mm (1/4" x 1/4" x 1/4"), square 2,32 to 3,44 m² (25 to 37 ft.²) Set times shown are based on 23 C (73 F) at 50% relative humidity. Actual times may vary depending on the size, ambient and substrate temperatures, and humidity levels. For more information, see individual Product Data Sheets and Chembond s Substrate Requirements for Tile document. The most recent information can be found at 6

8 CHEMBOND A Division of MAPEI Inc Williams Parkway Brampton, Ontario L6S 5X7 Phone: Edition date: January 19, 2016 PR: 7674 MKT: