Low cost because floor renovation can be completed the same day

Size: px
Start display at page:

Download "Low cost because floor renovation can be completed the same day"

Transcription

1 ARDEX SD-L ARDEX SD-L Technical Information & Installation Instructions Product Info Formatted Specifications MSDS Find in this page: Technical Information Installation Instructions Technical Information RANGE OF APPLICATION ARDEX SD-L provides for fast leveling over new or existing concrete, non-porous subfloors such as ceramic and quarry tile, terrazzo, cutback adhesive residues, and wooden subfloors. ARDEX SD-L can be installed to a maximum thickness of 1/2". Three hours after installation, the surface of ARDEX SD-L is ready to receive vinyl tile, vinyl-backed sheet goods, felt-backed sheet goods, linoleum, carpet, ceramic and quarry tile. PRODUCT DESCRIPTION ARDEX SD-L is an engineered concrete specially formulated to be mixed with water only, forming a liquid compound which installs quickly and easily with no troweling. ARDEX SD-L hardens by the chemical process of hydration. The resulting surface is flat and smooth and is ready to have flooring installed just three hours after placement. ADVANTAGES Install floor covering in three hours Low cost because floor renovation can be completed the same day Mixes with water only Based on engineered Portland cement technology No troweling Up to 1/2" deep in a single pour Can be readily installed to achieve 1/8" in 10 ft. tolerance No sanding or grinding Walkable after 1 to 2 hours Compatible with flooring adhesives Note: This product is intended for interior use over dry substrates only. Do not use in areas of constant water exposure nor in areas exposed to permanent or intermittent substrate moisture, as this may jeopardize the performance of the underlayment and the floor covering system. This product is not a vapor barrier and will allow free passage of moisture. Follow the directives of the floor covering manufacturer regarding the maximum allowable substrate moisture content and test the substrate prior to installing ARDEX SD-L.

2 Technical Data: Coverage: (per 50 lb. bag) Approximately 50 sq. ft. at 1/8" thickness Approximately 25 sq. ft. at 1/4" thickness, etc. Mixing Ratio: (part by volume) 1 part water to 3 parts powder Flowing Time: Approx. 10 minutes at 70ºF Initial Set: (ASTM C191) Approx. 15 minutes at 70ºF Final Set: (ASTM C191) Approx. 1 hour at 70ºF Compressive Strength: (ASTM C-109/mod.) 2750 psi after 1 day 4700 psi after 28 days Flexural Strength: (ASTM C348) 850 psi after 1 day 1200 psi after 28 days Flammability: (ASTM E-84-81a) Flame spread: 0 Fuel Contribution: 0 Smoke development: 0 All data based on a mixing ration of 1:3. p.b.v. at 70ºF SUBFLOOR PREPARATION Concrete floors: Must be solid, thoroughly clean, free of oil, wax, grease, latex patches, curing compounds, and any contaminant which might act as a bondbreaker, before priming with ARDEX P-51. Overwatered, frozen or otherwise weak concrete surfaces must be mechanically cleaned down to solid, sound concrete by shot -blasting, scarifying or similar. Acid etching is not an acceptable means of cleaning the subfloor. Non-porous floors, such as terrazzo, ceramic and quarry tile, certain power-troweled (burnished) concrete, and epoxy coatings: Must be solid, well bonded and properly cleaned and then primed with ARDEX P-82 Ultra Prime. Cut-Back Adhesive and non-water soluable adhesives on concrete and wooden subfloors: Refer to the instructions for installation of ARDEX SD-L over this substrate, located under a separate heading in this brochure. Gypsum, asphalt, coal tar, latex patches and most lightweight concretes are not suitable substrates for the installation of ARDEX SD-L. For further information, please refer to the ARDEX Substrate Preparation brochure.

3 Note: All subfloors must be dry and properly primed for a successful installation. Project temperatures must be consistent with those recommended by the manufacturer of the floor covering to be installed. Contact the ARDEX Technical Service Department for recommendations on the proper application of ARDEX SD-L for the given project. Always install an adequate number of properly located test areas, which include the finish flooring, to ensure the suitability of the product for its intended use. As floor coverings vary, always contact and rely upon the floor covering manufacturer for specific directives, to include requirements such as adhesive selection and intended end use of the product. RECOMMENDED TOOLS ARDEX T-1 Mixing Paddle, ARDEX T-10 Mixing Drum, ARDEX T-4 Spreader, ARDEX T-5 Smoother, ARDEX M-4.75 Measuring Bucket (4.75 quarts), 1/2" heavy-duty drill (minimum 650 rpm). PRIMING Standard absorbent concrete: Prime with ARDEX P-51 Primer diluted 1:1 with water. Apply evenly with a soft pushbroom. Do not use paint rollers, mops or spray equipment. Do not leave any bare spots. Brush off puddles and excess primer. Allow to dry to a clear, thin film (minimum 3 hours, maximum 24 hours). Extremely absorbent concrete may require two applications of ARDEX P-51 to avoid the formation of bubbles and pinholes in the ARDEX SD-L. In such cases, make an initial application of ARDEX P-51 diluted with 3 parts water. Let dry thoroughly (1 to 3 hours) and install a second application of ARDEX P-51 mixed 1:1 with water. Non-porous subfloors: Prime with ARDEX P-82 Ultra Prime. Mix Part A (red) with Part B (white) and apply with a short-nap or sponge paint roller, leaving a thin coat of primer no heavier than a thin coat of paint. Do not leave any bare spots. Brush off puddles and excess primer. Allow to dry to a thin, slightly tacky film (minimum 3 hours, maximum 24 hours). Caution: ARDEX P-82 must be applied in a thin layer within one hour of mixing. A thick application will produce a soft and rubbery surface which can result in cracking of the ARDEX SD-L. Note: Low surface temperatures and/or high ambient humidity require a longer drying time for ARDEX primers. Do not install ARDEX SD-L before the primer has dried thoroughly. MANUAL INSTALLATION ARDEX SD-L is mixed in two-bag batches at one time. For each bag, add 4.75 quarts (4.5 liters) of water. Put the water in the mixing drum first, then add each bag of ARDEX SD-L while mixing with an ARDEX T-1 Mixing Paddle and a 1/2" heavy-duty drill (minimum 650 rpm). Mix thoroughly for 2 to 3 minutes to obtain a lump-free mix. DO NOT OVERWATER. Check the consistency of the product on the substrate to ensure a uniform distribution of the sand aggregate at both the top surface and bottom of the pour. ARDEX SD-L has a flow time of 10 minutes at 70 F. Pour the liquid mix on the floor and spread with the ARDEX T-4 Spreader. Immediately smooth the material with the ARDEX T-5 Smoother. Wear baseball or soccer shoes with non-metallic cleats to avoid leaving marks in the liquid ARDEX SD-L. PUMPING INSTALLATION ARDEX SD-L can also be installed using an ARDEX Levelcraft Automatic Mixing Pump. The Levelcraft Pump provides for high productivity and a smoothly running consistent installation. The

4 Levelcraft Pump may be rented from a local authorized ARDEX Distributor and is fully supported by the ARDEX Technical Service Department. Start the pump at 150 gallons of water per hour, then adjust downward to the minimum water reading which still allows self- leveling properties. DO NOT OVERWATER! Conditions during the installation, such as variations in water, powder, substrate and ambient temperature, require that the water setting be monitored and adjusted carefully to avoid overwatering. ARDEX SD-L has a flow time of 10 minutes at 70 F. Pump the liquid mix on the floor and spread with the ARDEX T-4 Spreader. Immediately smooth the material with the ARDEX T-5 Smoother. Wear baseball or soccer shoes with non-metallic cleats to avoid leaving marks in the liquid ARDEX SD-L. Please contact the ARDEX Technical Service Department for complete pump installation instructions, to include the Operation and Instruction Guidelines. THICKNESS OF INSTALLATION ARDEX SD-L can be installed from a taper to 1/2" maximum. Do not layer ARDEX SD-L. For installations requiring depths greater than 1/2", use ARDEX K-15 Self-Leveling Underlayment Concrete. FLOORING INSTALLATION Regardless of the thickness poured, ARDEX SD-L can be walked on 1 to 2 hours after installation. Floor covering can be installed 1 to 2 hours later, depending upon ambient temperatures and humidity. Please note that wood flooring and rubber flooring can only be installed over ARDEX SD-L after allowing 16 hours of curing. NOTE ARDEX SD-L is a cementitious material. Observe the basic rules of concrete work. Do not install below 50 F surface temperature. Install quickly if subfloor is warm and follow hot weather precautions available from the ARDEX Technical Service Department. Never mix with cement or additives other than ARDEX-approved products. DO NOT OVERWATER! WEAR SURFACES ARDEX SD-L is not to be used as a wear surface, even if coated with an epoxy paint or similar. ARDEX SD-L must be covered by a suitable floor covering material, such as carpet, vinyl flooring, etc. For resurfacing and leveling indoor concrete floors in warehouses, storage areas, hallways, or other areas where a wear surface is required, use ARDEX K-500 Self-Leveling Concrete Topping or ARDEX SD-T Self-Drying, Self-Leveling Concrete Topping. ARDEX SD-L UNDERLAYMENT CONCRETE OVER CUTBACK AND OTHER NON-WATER SOLUABLE ADHESIVE RESIDUE INTRODUCTION Asphaltic cutback adhesive remaining on concrete floors after removing old vinyl tile and other flooring represents one of the most difficult and risky subfloors for the installation of new flooring. PROBLEM Mechanical removal of cutback (i.e., grinding, sanding, blasting) is rarely satisfactory and can be hazardous, as cutback adhesive may contain asbestos.

5 SOLUTION ARDEX SD-L will allow the installation of high-quality concrete underlayment without removing the cutback down to bare concrete. WARNING Cutback and other non-water soluable adhesives may contain asbestos fibers. Do not sand or grind adhesive residue, as harmful dust may result. Inhalation of asbestos dust may cause asbestosis or other serious bodily harm. Please consult the adhesive manufacturer and all applicable government agencies for rules and regulations concerning the removal of asbestoscontaining flooring and adhesives. The Resilient Floor Covering institute's pamphlet "Recommended Work Practices for the Removal of Resilient Floor Coverings" is available free of charge from the ARDEX Technical Service Department. NOTE Coal tar ("hot pitch") and asphalt waterproofing and roofing systems are not suitable substrates for this system. PREPARATION AND INSTALLATION Thick accumulations, powdery, brittle or otherwise weak adhesive layers must be removed, but only with extreme caution. Use the wet-scraping and wet-sweeping method as outlined in the Resilient Floor Covering Institute's "Recommended Work Practices for the Removal of Resilient Floor Coverings" to remove thick areas and build-ups of adhesive, and any areas that are weak and not well bonded to the substrate. The remaining residue should be almost transparent. Check the substrate for hollow spots, latex patches or otherwise weak areas and remove them. Wetmop the floor to remove all debris and loose material. It is the responsibility of the installation contractor to ensure that the subfloor is properly prepared prior to the installation of the ARDEX material. Broom and vacuum clean the cutback surface. Prime the subfloor with ARDEX P-51 mixed with 1/2 part by volume of water (1:0.5) and apply evenly with a soft pushbroom. Do not use paint rollers, mops, or spray equipment. Do not leave any bare spots. Brush off puddles and excess primer. Allow to dry for a minimum of 1 to 3 hours to a clear, thin film. Install ARDEX SD-L per the Manual or Pump installation instructions previously described. Allow 1 to 2 hours of drying before walking on the surface. Allow an additional 1 to 2 hours before installing the finish flooring. PRECAUTIONS ARDEX SD-L is intended for applications over non-soluble adhesive residues on concrete subfloors only. Avoid using high solvent-content adhesives over the underlayment, as the adhesive's solvent could migrate through the cementitious ARDEX SD-L layer, dissolving the cutback substrate and causing separation. Avoid installations over very warm floors (i.e., over hot machine shops, over concrete floors containing heating systems, etc.) as heat might soften the adhesive, causing failure. Always install an adequate number of properly located test areas. OTHER ADHESIVE RESIDUES

6 Installation of ARDEX SD-L over other types of adhesive is also possible if adhesive residue is solid, well-bonded to the subfloor and not affected by water. Test installations are always required. SUMMARY The use of ARDEX SD-L over cutback adhesive is a fast-track system which significantly reduces man-hours, installation expenses and hard work in floor remodeling. ARDEX SD-L UNDERLAYMENT CONCRETE OVER WOODEN SUBFLOORS The Mesh-Reinforced ARDEX SD-L Underlayment System INTRODUCTION One of the most common problems in renovation and remodeling of existing buildings is the leveling and smoothing of wooden subfloors, such as plywood and strip flooring, to receive other types of floor coverings. PROBLEM Wooden floors move under stress. They expand with temperature and humidity changes. Joints between boards can be very pronounced. The surfaces are often rough and uneven, with deviations from zero to several inches in ten feet. Covering these wooden subfloors with a layer of plywood underlayment is labor-intensive and will result in floor elevation problems at doorways and in hallways. Latex-cement and gypsum underlayments will crack along joints, break bond with the lateral wood movement, and often disintegrate when exposed to traffic stress. SOLUTION The Mesh-Reinforced ARDEX SD-L Underlayment System is a successful, fast-track method, which allows the installation of a high-quality concrete underlayment in a thin layer (3/8" minimum), while maintaining strength and flexibility to withstand normal wood movement and traffic stress. The resulting concrete surface is smooth and hard and is suitable for many types of flooring material, including resilient flooring and ceramic tile. PREPARATION AND INSTALLATION The wooden subfloors must be clean and free of oil, grease, wax, dirt, varnish, shellac, or any contaminant which might act as a bondbreaker. If necessary, sand down to bare wood. A commercial drum sander can be used to sand large areas. Do not use solvents, strippers or cleaners. Vacuum all dust and debris. The subfloor should be solid and fixed securely to provide a rigid base. Any boards exhibiting movement should be renailed. Open joints should be filled with ARDEX SD-F Self-Drying, Fast-Setting Concrete Underlayment Patch. It is the responsibility of the installation contractor to ensure that the subfloor is thoroughly clean and secure prior to the installation of ARDEX material. Prime the wooden subfloor with ARDEX P-82 Ultra Prime. Mix Part A (red) with Part B (white) and apply with a short-nap or sponge paint roller, leaving a thin coat of primer no heavier than a thin coat of paint. Do not leave any bare spots. Brush off puddles and excess primer. Allow to dry to a thin, slightly tacky film (minimum 3 hours, maximum 24 hours).

7 Caution: ARDEX P-82 must be applied in a thin layer within one hour of mixing. A thick application will produce a soft and rubbery surface which can result in cracking of the ARDEX SD-L. Note: Low surface temperatures and/or high ambient humidity require a longer drying time for ARDEX primers. Do not install ARDEX SD-L before the primer has dried thoroughly. Install 3.2 or 3.4 galvanized expanded diamond metal lath mesh to the subfloor, stapling approximately every 6 inches. Install ARDEX SD-L per the Manual or Pump installation instructions previously described. Allow 1 to 2 hours of drying before walking on the surface. Allow an additional 1 to 2 hours before installing the finish flooring. PRECAUTIONS Always install an adequate number of properly located test areas. TECHNICAL DATA Coverage: A 50 lb. bag covers approximately 50 sq. ft. at 1/8" thickness, 25 sq. ft. at 1/4 ", etc. Mixing Ratio: (Parts by volume) 1 part water to 3 parts powder Flow Time: Approximately 10 minutes at 70 F Initial Set, ASTM C191: Approximately 15 minutes at 70 F Final Set, ASTM C191: Approximately 60 minutes at 70 F Compressive Strength, ASTM C-109/mod.: 2750 psi after 1 day 4700 psi after 28 days Flexural Strength, ASTM C348: 850 psi after 1 days 1200 psi after 28 days Flammability, ASTM E-84-81a: Flame Spread 0 Fuel Contribution 0 Smoke Development 0 All data based on a mixing ratio of 1:3 p.b.v. at 70 F. Packaging: 50 lbs / 22.7 kg bags. Storage: Store in a cool, dry area. Do not expose bags to sun. Shelf Life: Six months. LIMITED WARRANTY: ARDEX Limited Warranty Applies

SECTION HYDRAULIC CEMENT UNDERLAYMENT

SECTION HYDRAULIC CEMENT UNDERLAYMENT ARDEX GUIDE SPECIFICATION ARDEX Underlayment HC 100 High-Capacity Self-Leveling and V1200 Self-Leveling Flooring Underlayment Cement-based Self-Leveling Underlayment for use with ARDEX ARDIFLO System SECTION

More information

NXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N

NXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N NXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N Substrate preparation is the most important factor to successful NXT self-leveling underlayment (SLU) and NXT Vapor Reduction Coating installations.

More information

TechLevel 125 Deep Pour Self-Leveling Underlayment

TechLevel 125 Deep Pour Self-Leveling Underlayment 1 Product Name 2 Manufacturer Custom Building Products Technical Services 10400 Pioneer Boulevard, Unit 3 Santa Fe Springs, CA 90670 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax:

More information

Fiber Reinforced Tile and Stone Mortar

Fiber Reinforced Tile and Stone Mortar , ANSI A 118.4, ANSI A 118.11 ARDEX X 77 MICROTEC Fiber Reinforced Tile and Stone Mortar The most advanced technology ideal for large format porcelain tile installations,exterior or interior, floor or

More information

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE

More information

ARDEX GUIDE SPECIFICATION

ARDEX GUIDE SPECIFICATION ARDEX GUIDE SPECIFICATION ARDEX PC-T Part of the ARDEX Polished Concrete System (APCS) SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general

More information

1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.

1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU. 1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate

More information

ARDEX X 90 OUTDOOR TM

ARDEX X 90 OUTDOOR TM ANSI A 118.15, ANSI A 118.4, ANSI A 118.11 ARDEX X 90 OUTDOOR TM MicroteC3 Rapid-Set, Flexible Tile and Stone Mortar Maximum weatherproof protection against the harshest elements for outdoor tile and stone

More information

FLOORING INSTALLATION SYSTEMS. Product Catalog

FLOORING INSTALLATION SYSTEMS. Product Catalog FLOORING INSTALLATION SYSTEMS Product Catalog Custom Building Products is North America s leader in flooring preparation systems. It s easy to say you re an industry leader, but we prove it every day with

More information

Suggested Specification for Tri-Patch Versatile Concrete Patching Compound

Suggested Specification for Tri-Patch Versatile Concrete Patching Compound Suggested Specification for Tri-Patch Versatile Concrete Patching Compound SURFACE PREPARATION for Interior and Exterior Floor-Covering Installations. (Vinyl Composition Tiles, Sheet Vinyl, Rubber, Indoor

More information

KOSTER AMERICAN CORPORATION

KOSTER AMERICAN CORPORATION Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General

More information

ARDEX X 32 MICROTEC Universal Rapid Setting and Drying Thin-to-Thick Bed Mortar

ARDEX X 32 MICROTEC Universal Rapid Setting and Drying Thin-to-Thick Bed Mortar ANSI A 118.15, ANSI A 118.4, ANSI A 118.11 ARDEX X 32 MICROTEC Universal Rapid Setting and Drying Thin-to-Thick Bed Mortar The fast track, interior or exterior, thin-to-thick bed solution for every natural

More information

Installation Guide LVP Glue Down

Installation Guide LVP Glue Down 734 SOUTH RIVER STREET CALHOUN, GEORGIA 1.844.225.3100 www.encorehospitalitycarpet.com Installation Guide LVP Glue Down Materials Required for Installation: Tape Measure Square ruler Chalk line Utility

More information

ENGINEERED LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING

ENGINEERED LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING ENGINEERED LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to

More information

SECTION LATEX-MODIFIED MEDIUM BED MORTAR

SECTION LATEX-MODIFIED MEDIUM BED MORTAR SECTION 09305.24 LATEX-MODIFIED MEDIUM BED MORTAR This product guide specification can be used to specify Hydroment Big Tile & Stone Mortar, a latex-modified, medium bed mortar designed for setting large

More information

ARDEX GUIDE SPECIFICATION ARDEX PC-T POLISHED CONCRETE TOPPING Part of the ULTRAFLOR ARDEX DIAMATIC Polished Concrete System

ARDEX GUIDE SPECIFICATION ARDEX PC-T POLISHED CONCRETE TOPPING Part of the ULTRAFLOR ARDEX DIAMATIC Polished Concrete System ARDEX GUIDE SPECIFICATION ARDEX PC-T POLISHED CONCRETE TOPPING Part of the ULTRAFLOR ARDEX DIAMATIC Polished Concrete System SECTION 03 35 53 POLISHED CONCRETE TOPPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

More information

Contents. SUPPORTING PRODUCTS UL-Primer 24 Moisture Seal 24 Megalastic 25

Contents. SUPPORTING PRODUCTS UL-Primer 24 Moisture Seal 24 Megalastic 25 Floor Levelling 2 Contents Bostik Green Commitment 4 Pictograms 7 Cementitous Floor Levelling Compounds 8 Floor Levelling Characteristics, Specifications And Technical Support 9 Application Instructions

More information

LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR LOCKING FLOORING

LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR LOCKING FLOORING LUXURY VINYL GENERAL INSTALLATION INSTRUCTIONS FOR LOCKING FLOORING ACCLIMATION Acclimation is required prior to the installation of Luxury Vinyl Flooring (LVF). Store the UNOPENED BOXES in the room where

More information

ARDEX UI 740 TM FLEXBONE

ARDEX UI 740 TM FLEXBONE ARDE UI 740 TM FLEBONE Uncoupling Membrane FLEBONE - The most advanced, single-source uncoupling solutions! High load-bearing uncoupling membrane Ideal for large format tile and stone in heavy traffic

More information

Specification and Installation

Specification and Installation SHAW 5800 SPECIFICATION ADHESIVE FOR SHAW CARPET TILE Any variance from these procedures will become the responsibility of the installer and not the manufacturer. See Shaw s Modular Installation Guidelines

More information

ENGINEERED WATERPROOF FLOORING GENERAL INSTALLATION INSTRUCTIONS FOR VÄLINGE 2G LOCKING FLOORING

ENGINEERED WATERPROOF FLOORING GENERAL INSTALLATION INSTRUCTIONS FOR VÄLINGE 2G LOCKING FLOORING ENGINEERED WATERPROOF FLOORING GENERAL INSTALLATION INSTRUCTIONS FOR VÄLINGE 2G LOCKING FLOORING SITE CONDITIONS Always store the boxes of Engineered Waterproof Flooring (EWF) on a flat and level surface;

More information

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings. SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

Installation Instructions

Installation Instructions Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING

More information

Specification Data -- RESILIENT TILE FLOORING

Specification Data -- RESILIENT TILE FLOORING Specification Data -- RESILIENT TILE FLOORING 09 65 19 Burke Flooring Luxury Vinyl Tile Installation Instructions In any floor covering installation there are four basic requirements to insure a proper

More information

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS SECTION 09699 MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS PART 1 GENERAL 1.1 SECTION INCLUDES A. Testing and application of systems for the reduction of moisture resistant or water-proof

More information

UNDERLAYMENT INSTALLATION INSTRUCTIONS

UNDERLAYMENT INSTALLATION INSTRUCTIONS UNDERLAYMENT INSTALLATION INSTRUCTIONS Table of Contents BASE PREPARATION I. General Information... 3 II. Job Site Conditions... 3 III. Subfloor Requirements & Preparation...3 IV. Hazards... 4 V. Material

More information

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS

SECTION COMMON WORK RESULTS FOR CONCRETE SSPECIALTY COATINGS SECTION 03 05 00 COMMON WORK RESULTS FOR CONCRETE 09 97 00 SSPECIALTY COATINGS Weld Crete ************************************************************************************************************************

More information

INSTALLATION AND MAINTENANCE MANUAL

INSTALLATION AND MAINTENANCE MANUAL Athletic Vinyl Padded Roll AND MAINTENANCE MANUAL Greatmats.com 117 Industrial Ave Milltown, WI 54858 P: 877-822-6622 F: 715-825-4928 info@greatmats.com TABLE OF CONTENTS Job Site Conditions 3 Subfloors

More information

Resilient and Wood Floor Covering Flatness Requires High Performance, Cementitious Self-Leveling Underlayment

Resilient and Wood Floor Covering Flatness Requires High Performance, Cementitious Self-Leveling Underlayment Resilient and Wood Floor Covering Flatness Requires High Performance, Cementitious Self-Leveling Underlayment By Steve Taylor Director of Architecture and Technical Marketing, Custom Building Products

More information

RESILIENT FLOORING: Select Step Wood

RESILIENT FLOORING: Select Step Wood 160 S. Industrial Blvd Calhoun, GA 30701 Section 096519 RESILIENT FLOORING: Select Step Wood This document is intended as a suggested guide for editing your architectural guide specification. Mohawk Group

More information

USG DUROCK BRAND X FLOOR PATCH. USG Performance Flooring Solutions SUBMITTAL SHEET

USG DUROCK BRAND X FLOOR PATCH. USG Performance Flooring Solutions SUBMITTAL SHEET USG Performance Flooring Solutions SUBMITTAL SHEET USG DUROCK BRAND X FLOOR PATCH Versatile, trowelable cementitious patching compound For interior use over properly prepared concrete, gypsum and approved

More information

Make your floor a unique artwork!

Make your floor a unique artwork! Make your floor a unique artwork! Content: Floor Expert EP 101... 08 Floor Expert EP 1013... 09 Floor Expert EP 310W... 10 Floor Expert EP 311...11 Floor Expert EP 211... 12 Floor Expert EP Combines design

More information

Access Luxury Vinyl Flooring Installation Guidelines

Access Luxury Vinyl Flooring Installation Guidelines GENERAL All recommendations are based on the most recent available information. The information on these sheets provides general guidelines. For additional details, visit our website at manningtoncommercial.com.

More information

Technical Service. INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products. This document refers to the following products:

Technical Service. INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products. This document refers to the following products: INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products This document refers to the following products: Product Width Width Ft. Installation direction Seams treatment Taraflex Surface

More information

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box

More information

The following instructions should be reviewed prior to installation. Shaw Industries will not be responsible for improper installation.

The following instructions should be reviewed prior to installation. Shaw Industries will not be responsible for improper installation. Installation of Shaw Contract Group Modular Carpet (Ecoworx, Ecoworx ES, Ecologix, Ergoflex, Ergoflex ES) INSTALLATION GUIDELINES The following instructions should be reviewed prior to installation. Shaw

More information

Application Instructions for Keystone Kool Deck on Existing Concrete

Application Instructions for Keystone Kool Deck on Existing Concrete Application Instructions for Keystone Kool Deck on Existing Concrete REQUIRED MATERIALS Keystone Kool Deck PTA Bonding Agent Water 20 Mesh Marble Sand White Portland Cement OPTIONAL TOOLS Mortex Pattern

More information

Installation Products

Installation Products TM TM TM Installation Products LVT/Vinyl Sheet Adhesives Flip Spray Adhesive High-moisture guarantee Recommended for heavy rolling loads Simple one-step application process Allows immediate traffic Open

More information

Sikafloor -161 is an economic, two part, solvent free, low viscosity epoxy resin, suitable for use under hot climate condition.

Sikafloor -161 is an economic, two part, solvent free, low viscosity epoxy resin, suitable for use under hot climate condition. Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -161 2-part epoxy primer, levelling mortar, intermediate layer and mortar screed Construction Product Description Sikafloor -161

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell WB 50 Product Specification GUIDE SPECIFICATION SECTION 09725

More information

prospec.com Concrete Repair & Restoration

prospec.com Concrete Repair & Restoration prospec.com Concrete Repair & Restoration Table of Contents Product Portfolio 3 Product Enhancements 4 Product Selection Matrices 5 Construction Grout & Precast Non-shrink grouts C-1107 Construction Grout

More information

RESILIENT FLOORING: Hot and Heavy - Secoya

RESILIENT FLOORING: Hot and Heavy - Secoya 160 South Industrial Blvd. Calhoun, GA 30701 Section 096519 RESILIENT FLOORING: Hot and Heavy - Secoya This document is intended as a suggested guide for editing your architectural guide specification.

More information

Luxury Vinyl Plank Installation Manual 2017

Luxury Vinyl Plank Installation Manual 2017 Luxury Vinyl Plank Installation Manual 2017 The van Gelder, Inc. Installation Manual has been created as a guide for people who specify, sell and install van Gelder, Inc. Solid Vinyl Floor Tile for commercial

More information

Kolorines Glass Mosaic Tiles Project Specification

Kolorines Glass Mosaic Tiles Project Specification Kolorines Glass Mosaic Tiles Project Specification SUGGESTED SPECIFICATION Glass Mosaic Tile Installation for Swimming Pools NOTES TO SPECIFIER: 1. Specify PremiumPlus Thin-Set mixed with CustomFlex Additive

More information

TECHNICAL DATA SHEET SIKALEVEL 25 LATEX SELF LEVELLING 25KG

TECHNICAL DATA SHEET SIKALEVEL 25 LATEX SELF LEVELLING 25KG TECHNICAL DATA SHEET SIKALEVEL 25 LATEX SELF LEVELLING 25KG SikaLevel 25 Latex Self Levelling is a ready to use latex modified cement based self leveller for floor smoothing and preparation of uneven

More information

USG DUROCK BRAND ULTRACAP PRO SELF-LEVELING UNDERLAYMENT. USG Performance Flooring Solutions SUBMITTAL SHEET

USG DUROCK BRAND ULTRACAP PRO SELF-LEVELING UNDERLAYMENT. USG Performance Flooring Solutions SUBMITTAL SHEET USG Performance Flooring Solutions SUBMITTAL SHEET USG DUROCK BRAND ULTRACAP PRO SELF-LEVELING UNDERLAYMENT Portland cement-based poured underlayment Ideal over concrete and wood subfloors Fast application,

More information

DIVISION 9 FINISHES Section Floor Finishes

DIVISION 9 FINISHES Section Floor Finishes Spec Component: SC-032-0807 Supersedes: SS-032-0601 DIVISION 9 FINISHES Section 09600 Floor Finishes Part 1 - General 1.01 Summary A. This specification describes the application of a waterproofing, slip

More information

Installation Instructions for CushionBac Renew Tiles

Installation Instructions for CushionBac Renew Tiles Installation Instructions for CushionBac Renew Tiles Important Notices These Installation Instructions cover most installation procedures. If you run across a situation that isn t addressed in this document

More information

Installation Instructions

Installation Instructions Installation Instructions KEY MMA SLT QUARTZ I. GENERAL INFORMATION KEY MMA SLT QUARTZ is a rapid curing, 100% reactive, decorative methyl methacrylate (MMA) resin flooring system. Thickness ranges from

More information

ALTERNA ENGINEERED Tiles & Plank

ALTERNA ENGINEERED Tiles & Plank ALTERNA ENGINEERED Tiles & Plank Installation System Product Gauge Size Adhesive Comment 8"x8" (20.3 cm x 20.3 cm) ALTERNA ALTERNA RESERVE ALTERNA PLANK 0.160 (4.1 mm) 8"x16"(20.3 cm x 40.6 cm) 12"x12"(30.5

More information

Product Width Thickness Installation direction Seam treatment. Taraflex Sport M Comfort Approximately mm + 5mm Same Heat Welded

Product Width Thickness Installation direction Seam treatment. Taraflex Sport M Comfort Approximately mm + 5mm Same Heat Welded INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT M COMFORT This document refers to the following product: Product Width Thickness Installation direction Seam treatment Taraflex Sport M Comfort Approximately

More information

SECTION WOOD FLOORING. 1. Section Above-Grade Vapor Retarders. 2. Section Below-Grade Vapor Retarders

SECTION WOOD FLOORING. 1. Section Above-Grade Vapor Retarders. 2. Section Below-Grade Vapor Retarders SECTION 09 64 00 WOOD FLOORING PART 1 GENERAL 1.1 SECTION INCLUDES A. Flooring Vapor Retarders 1.2 RELATED SECTIONS A. Section 07 26 00 Vapor Retarders 1. Section 07 26 13 Above-Grade Vapor Retarders 2.

More information

CC-1004 Ultra High Temperature Epoxy Adhesive

CC-1004 Ultra High Temperature Epoxy Adhesive CC-1004 Ultra High Temperature Epoxy Adhesive PRODUCT DESCRIPTION TYPICAL USES Blome CC-1004 is a two part, high temperature, epoxy adhesive used for the installation of abrasion resistant brick and tile

More information

POLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE

POLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE RECOMMENDED APPLICATIONS Polymer Concrete 100 is a three-component, epoxy polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete 100

More information

SIDER-POOL. Product Data. Features and Uses

SIDER-POOL. Product Data. Features and Uses 153 Regur Road Hawkinsville, GA 31036 USA 1.478.892.9800 888-743-3750 sales@sider-crete.com www.sider-crete.com Product Data Features and Uses A true cement-based plaster No-check cracking and no-brushing

More information

Ash Brook Golf Course Scotch Plains, New Jersey

Ash Brook Golf Course Scotch Plains, New Jersey SECTION 033543 - POLISHED CONCRETE FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

ARDEX AMERICAS I Wear Surface Toppings

ARDEX AMERICAS I Wear Surface Toppings ARDEX AMERICAS I Wear Surface Toppings ARDEX Polished Concrete Systems TM ARDEX Designer Floors TM Concrete Resurfacing ARDEX MC TM Moisture Control Systems ARDEX Americas, one of the largest ARDEX corporate

More information

VINYL COMPOSITION TILE

VINYL COMPOSITION TILE ASSET Reference Specification ASTM F 1066-99 Standard Specification for Vinyl Composition Floor Tile Products: Azrock s Vinyl Composition Tile -Standard Price Products -Premium Priced Products -Slip Resistant

More information

OVERKOTE E-100 Epoxy Floor Coating Technical Data

OVERKOTE E-100 Epoxy Floor Coating Technical Data OVERKOTE E-100 Epoxy Floor Coating Technical Data PRODUCT DESCRIPTION OVERKOTE E-100 is a floor coating system applied at a thickness of 16 to 50 mils. It is designed for long term protection of concrete

More information

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,

More information

SECTION RESILIENT SHEET FLOORING

SECTION RESILIENT SHEET FLOORING SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.

More information

Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6

Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6 Section II Subfloor Guidelines & Specifications Page Chapter 4 Wood Subfloor Guidelines 23 Chapter 5 Concrete Subfloor Guidelines 26 Chapter 6 Installing a Subfloor Over Concrete 27 24 National Wood Flooring

More information

SECTION WOOD FLOORING

SECTION WOOD FLOORING SECTION 09 64 00 WOOD FLOORING PART 1 GENERAL 1.1 SECTION INCLUDES A. Flooring Acoustic Membranes 1.2 RELATED SECTIONS A. Section 09 62 00 Specialty Flooring 1. Section 09 62 48 Acoustic Flooring B. Section

More information

CHARACTERISTICS / ADVANTAGES

CHARACTERISTICS / ADVANTAGES PRODUCT DATA SHEET Water resistant, S.B.R. bonding agent and mortar additive PRODUCT DESCRIPTION Sika Latex is a modified styrene butadiene emulsion that is mixed normally with cement to form a bonding

More information

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards.

1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. WOOD FLOORING GENERAL INFORMATION 1.1 This section applies to factory finished wood strip flooring. 1.2 Reference Standard: NOFMA - National Oak Flooring Manufacturers Association Grading Standards. 1.3

More information

Installation Instructions

Installation Instructions Installation Instructions Before you begin, you will need the following tools and supplies: A clean or new 5 gallon bucket. You will need to either replace or clean your bucket after each 5 kits or before

More information

Vapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring

Vapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring advanced moisture control, inc. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring 250 polished concrete slabs! Made in Southern California,

More information

1. Division 09 Section "Rough Carpentry."

1. Division 09 Section Rough Carpentry. GREENSPOINT AND LAUDER RD. EC/PRE-KlK PAGE 1 SECTION 096400 - WOOD FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

ComforTech Cushioned Rubber Sheet Flooring

ComforTech Cushioned Rubber Sheet Flooring ComforTech Cushioned Rubber Sheet Flooring Installation Instructions Introduction Johnsonite ComforTech Rubber flooring features an exclusive construction that enhances thermal insulation, sound absorption,

More information

ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT

ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 9/30/2009 AC 150/5370-10E ITEM P-631 REFINED COAL TAR EMULSION WITH ADDITIVES, SLURRY SEAL SURFACE TREATMENT 631-1.1 GENERAL. This item shall consist of a mixture of refined coal tar emulsion, mineral

More information

SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS ; /19; ;

SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS ; /19; ; SUPER-KRETE SPECIFICATION S-1 EXISTING CONCRETE SURFACE PREPARATION SECTIONS 01 71 16; 02 25 16/19; 03 01 30; 0716 16 SUPER-KRETE International, Inc. This product guide specification is written according

More information

CHARACTERISTICS / ADVANTAGES. Yellowish-transparent. PACKAGING 20 kg per pail

CHARACTERISTICS / ADVANTAGES. Yellowish-transparent. PACKAGING 20 kg per pail PRODUCT DATA SHEET Epoxy-resin binder for priming, levelling mortar and for screeds PRODUCT DESCRIPTION Sikafloor -156 is a colourless, 2-component low viscosity epoxy resin. USES For priming and levelling

More information

By CTS Cement Manufacturing Corp.

By CTS Cement Manufacturing Corp. CSI SECTION 03 60 00 GROUTING 03 62 00 NON-SHRINK GROUTING 03 62 13 NON-METALLIC NON-SHRINK GROUTING High Flow, Non-Metallic, Multi-Purpose, Cementitious, Non-Shrink Grout EDITOR NOTE: The following guideline

More information

Construction. Sikadur 31, Hi-Mod Gel. Application Instructions. Sika Corporation

Construction. Sikadur 31, Hi-Mod Gel. Application Instructions. Sika Corporation 1 Sikadur 31, Hi-Mod Gel Application Instructions Sikadur 31, Hi-Mod Gel Structural epoxy paste adhesive Two-component 100% solids Solvent-free Moisture-tolerant High-strength High-modulus Sikadur 31,

More information

Construction. Sodium silicate based surface hardener, dustproofer, sealing and curing compound for concrete. Product Description.

Construction. Sodium silicate based surface hardener, dustproofer, sealing and curing compound for concrete. Product Description. Construction Product Data Sheet Edition 19 November 2012 Sikafloor -CureHard-24 Sodium silicate based surface hardener, dustproofer, sealing and curing compound for concrete Product Description Sikafloor

More information

INSTALLATION INSTRUCTIONS FOR GERFLOR TARASAFE ULTRA VINYL SHEETGOODS

INSTALLATION INSTRUCTIONS FOR GERFLOR TARASAFE ULTRA VINYL SHEETGOODS INSTALLATION INSTRUCTIONS FOR GERFLOR TARASAFE ULTRA VINYL SHEETGOODS This document refers to the following products: Product Width Thickness Installation direction Seam treatment Tarasafe Geo Approximately

More information

***********************************************************************************

*********************************************************************************** AQUAFIN-2K/M Two-Component Cement-based Acrylic-based Waterproofing GUIDE AQUAFIN, Inc. SPECIFICATION PART 1 - GENERAL 1.1 SECTION INCLUDES SECTION 07 16 14 ACRYLIC MODIFIED (FLEXIBLE) CEMENTITIOUS WATERPROOFING

More information

IVC US Residential Installation Guide - Sheet Vinyl. Leading the Way

IVC US Residential Installation Guide - Sheet Vinyl. Leading the Way IVC US Residential Installation Guide - Sheet Vinyl Leading the Way IVC US Residential Installation Guide - Sheet Vinyl Flooring There are three methods of installation suitable for IVC US residential

More information

Amtico QuickStix LVF Installation

Amtico QuickStix LVF Installation GENERAL These instructions cover all fully adhered installations of Amtico Luxury Vinyl Floors (LVF) available in both Tile (LVT) and Plank (LVP). This includes: Amtico, Amtico 30 and Spacia luxury vinyl

More information

Technical Data Sheet

Technical Data Sheet MATTE CONTRACTOR CHOICE PAINT The Matte Contractor Choice C paint is designed for the contractor; it has good performance and opacity. No odor. Has very good brushability, leveling, durability, adhesion

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4

Two component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4 Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical

More information

Commercial Resilient Sheet Flooring

Commercial Resilient Sheet Flooring Commercial Resilient Sheet Flooring INSTALLATION 160 South Industrial Blvd. Calhoun, GA. 30701 MohawkGroup.com Technical Services Department 508 East Morris St. Dalton, GA 30721 800.833.6954 product_tech@mohawkind.com

More information

Liquid applied polyurea hybrid membrane

Liquid applied polyurea hybrid membrane Product Data Sheet Edition 07/08/2008 Identification no: 02 06 07 01 001 0 000015 Sikalastic -842 BG Liquid applied polyurea hybrid membrane Product Description Sikalastic -842 BG is a two part, highly

More information

DULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS

DULUX INTERIOR LUXURIOUS SILK TECHNICAL DATA SHEET Version SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS TECHNICAL DATA SHEET Version 1 2016 SEPTEMBER THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A low odour premium quality interior mid sheen finish with supreme stain resistance. PRODUCT

More information

Associated Spec Consultants, Inc. February 27, 2014 SECTION ARCHITECTURAL COATINGS

Associated Spec Consultants, Inc. February 27, 2014 SECTION ARCHITECTURAL COATINGS SECTION 099650 ARCHITECTURAL COATINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Application Specification Over Concrete Substrates

Application Specification Over Concrete Substrates Purpose and Scope Instructions for surface preparation and application of Dex-O-Tex Auto-Dex V as a protective and water resistant coating system for parking decks. Note: Working cracks in the concrete

More information

Construction. 2-part epoxy primer. Product Data

Construction. 2-part epoxy primer. Product Data Construction Product Data Sheet Edition 2 May 2013 Sikafloor -161 2-part epoxy primer Product Description Sikafloor -161 is an economic, two part, low viscosity epoxy resin for the use where substrate

More information

A. ASTM C 150 Standard Specification for Portland Cement. B. ASTM C 595 Standard Specification for Blended Hydraulic Cements.

A. ASTM C 150 Standard Specification for Portland Cement. B. ASTM C 595 Standard Specification for Blended Hydraulic Cements. TECHNICAL SPECIFICATIONS SEWER MANHOLE REHABILITATION SYSTEM WITH A PROTECTIVE CEMENT LINER AND HIGH BUILD EPOXY COATING (As Provided by Standard Cement Materials) FOREWORD The following specification

More information

Drying of Concrete TDS 183

Drying of Concrete TDS 183 Drying of Concrete TDS 183 As the occurrence of fast track construction continues to rise, the need to install a finished floor on a wet concrete slab is typically far too soon for the floor covering.

More information

CONDUCTIVE RESILIENT FLOORING

CONDUCTIVE RESILIENT FLOORING THIS DOCUMENT IS INTENDED AS A SUGGESTED GUIDE FOR CREATING, MODIFYING, OR EDITING YOUR CSI FORMATTED 3-PART ARCHITECTURAL GUIDE SPECIFICATIONS. JOHNSONITE WILL NOT BE LIABLE FOR ANY DAMAGES ARISING OUT

More information

General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.

General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound.

More information

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating. This resinous flooring specification consists of a flexible hybrid polymer primer and basecoat, urethane concrete slurry resurfacer, and double broadcast decorative vinyl flake system based on aliphatic

More information

Signature Seal 100 Medium-to-High Sheen Sealer VOC Characteristics and Applications

Signature Seal 100 Medium-to-High Sheen Sealer VOC Characteristics and Applications Signature Seal 100 Medium-to-High Sheen Sealer - 100 VOC DESCRIPTION Legacy Signature Seal is a high-gloss, UV-resistant, lacquer-based, crystal-clear sealer. A light coating of Legacy Signature Seal will

More information

FlexLok Adhesive Tabs for Carpet Tile

FlexLok Adhesive Tabs for Carpet Tile FlexLok Adhesive Tabs for Carpet Tile INSTALLATION EcoFlex ICT EcoFlex NXT 160 South Industrial Blvd. Calhoun, GA. 30701 MohawkGroup.com Technical Services Department 508 East Morris St. Dalton, GA 30721

More information

ITEM 458 WATERPROOFING FOR STRUCTURES

ITEM 458 WATERPROOFING FOR STRUCTURES ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures

More information

Carpet Tile & Plank Direct Glue Down

Carpet Tile & Plank Direct Glue Down Carpet Tile & Plank Direct Glue Down INSTALLATION EcoFlex ICT EcoFlex NXT EcoFlex AIR 160 South Industrial Blvd. Calhoun, GA. 30701 MohawkGroup.com Technical Services Department 508 East Morris St. Dalton,

More information

PROTECTO-CRETE 900/900SF

PROTECTO-CRETE 900/900SF FEATURES PC-900 PC-900SF Excellent Chemical Resistance Excellent Wear Resistance Excellent Bond Strength to Concrete RECOMMENDED APPLICATIONS Tensile Bond Strength ASTM D-7234 Cohesive Failure Same of

More information

9 RUBBER TRACK SURFACING (INDOOR APPLICATIONS) (FOR ALL SPORTFLEX, SUPER X AND MONDOTRACK PRODUCTS)

9 RUBBER TRACK SURFACING (INDOOR APPLICATIONS) (FOR ALL SPORTFLEX, SUPER X AND MONDOTRACK PRODUCTS) 9 RUBBER TRACK SURFACING (INDOOR APPLICATIONS) (FOR ALL SPORTFLEX, SUPER X AND MONDOTRACK PRODUCTS) DISCLAIMER: Refer to page 6 of this document. WARNING: THESE INSTALLATION INSTRUCTIONS ARE FOR INDOOR

More information

Waterproofing and Damp-proofing Cementitious Slurry

Waterproofing and Damp-proofing Cementitious Slurry Product Data Sheet Edition: 01/10/2012 Identification no. Version no: GCC SikaTop Seal-107 SikaTop Seal-107 Waterproofing and Damp-proofing Cementitious Slurry Product Description Uses SikaTop Seal-107

More information