DESIGN BASIS FOR AIR CONDITIONING AND VENTILATION SYSTEM FOR SUBSTATION AND CONTROL BUILDING HINDUSTAN PETROLEUM CORPORATION LTD.

Size: px
Start display at page:

Download "DESIGN BASIS FOR AIR CONDITIONING AND VENTILATION SYSTEM FOR SUBSTATION AND CONTROL BUILDING HINDUSTAN PETROLEUM CORPORATION LTD."

Transcription

1 CONDITIONING AND VENTILATION FOR SUBSTATION AND CONTROL BUILDING HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT TEIL JOB NO.: 6261 DOCUMENT NO.: 6261-HVAC-PKG-300 TEIL SPECIFICATION NO.: For Bid Enquiry DVM AVP SJP Revised as per Client AMR SMW SVW Comments 0 For Bid Enquiry AMR / ARN SMW SVW Rev no. issue date Description Prepared by Checked by Approved by TOYO ENGINEERING INDIA LIMITED MUMBAI INDIA

2 DOC.No HVAC-PKG-300 DHT PROJECT Page 2 of 7 Sr. No. DESCRIPTION PAGE 1 General 3 2 Codes and Standards 3 3 Special requirements 3 4 Safety requirements 3 5 Design Basis for Air Conditioning System 4 6 Design Basis for Ventilation System 5 7 Air Conditioning & Ventilation System Equipments & Material 6

3 DOC.No HVAC-PKG-300 DHT PROJECT Page 3 of GENERAL This specification covers the minimum requirements for the design, engineering, manufacture, inspection, testing and supply of Air Conditioning & Ventilation system. In addition to concurrence to this specification following consideration to be taken: 1. Compliance with applicable national or overseas codes & standards as well as any statutory regulation in existence for a specific item. 2. All equipment shall be sourced from PMC s mandatory / recommended Vendor List. The supplied model shall have proven track record. 3. Facility for any known future expansion of plant capacity with a minimum of modifications or shutdown. 2.0 CODES AND STANDARDS The main codes, standards wherever applicable for each equipment or system are indicated in the technical specifications of respective systems. Other reference documents, as applicable, are also listed in these corresponding specifications wherein the requirements of various codes and standards are amended or supplemented for compliance by the Contractors. 3.0 SPECIAL REQUIREMENT 3.1 Contractor shall develop the system taking into consideration the requirements defined in Feed package, Specifications, Data sheets. 3.2 Equipment shall be complete in all respects and any item or feature not covered in the specification, but essential for proper operation shall be included by the Contractor. Also the plant shall conform in all respects to high standards of engineering design, state of art, reliability and continuous operation. 3.3 Package Equipment layouts shall be prepared taking into consideration various factors like requirement of operatability, approach, safety withdrawal space requirement, maintenance, foundation requirements etc. for convenient operation. 3.4 Selection, fabrication and installation of piping works shall meet the Piping requirements defined elsewhere in Feed Package. 3.5 Design, engineering, fabrication, testing of vessels / storage tank shall meet the specifications enclosed elsewhere in the Feed Package. 3.6 Electrical equipment and material shall be in accordance with the electrical specifications enclosed elsewhere in the feed Package. All equipment selected for hazardous area shall be certified by the Testing Authority as specified in Electrical specifications or equivalent international testing agency for the service and area in which it is to be used.

4 DOC.No HVAC-PKG-300 DHT PROJECT Page 4 of The controls / indicators which are required to be connected to remote control room (DCS) shall be terminated in a junction box (with terminal strip) or local panel (located at the edge of skid) as applicable. 3.8 Selection & Installation of Instrumentation & controls shall meet minimum requirements defined in the Instrument specification attached elsewhere in Feed Package. 4.0 SAFETY REQUIREMENTS 4.1 Operational hazards should be reduced to a minimum. Contractor shall use sound engineering judgment to complete an installation that will perform the required function without compromising this aim. 4.2 Electrical devices shall meet the requirements for the area classifications in which they are installed. 4.3 Couplings, gears and exposed rotating parts shall be provided with adequate guards of nonsparking type. Drive belts, if used, shall be antistatic type. 4.4 Piping shall be arranged in a manner so as to avoid tripping or headroom problem. Piping or tubing of insufficient mechanical strength for standing or hanging shall be protected from personnel traffic. 4.5 Requirements of noise limits and equipment vibration as defined in standard specification shall be met. 5.0 DESIGN BASIS FOR AIR CONDITIONING 5.1 Air Conditioning shall be provided for the Sub-Station-75 Building. Contractor shall develop the complete Air Conditioning system configuration and submit along with bid and also before starting the detailed engineering work for owner/pmc approval. 5.2 The air Conditioning System shall be air cooled based system for the Sub-Station-75 Building. 5.3 Air Conditioning unit shall be available for continuous and round the clock operation. All areas requiring air conditioning for 24 hrs. /day. Following redundancy shall be maintained in Air Conditioning System; a) Water cooled chiller - 100% standby. b) VAM No standby. c) Fresh Air Fan - 100% standby. d) Chemical Filter Unit - No standby. e) AHU Upto 3 nos AHU s, 1 no standby, for 4 no and above, 2 no standby. f) Chilled water pumps - 100% standby. g) Cooling water pumps - 100% standby. h) Exhaust fans No standby. i) Exhaust fans for Battery Room Minimum 1 no of fan as standby j) Supply air fans for Battery Room Minimum 1 no of fan as standby k) FRP Cooling Tower with Basin 100% Standby.

5 DOC.No HVAC-PKG-300 DHT PROJECT Page 5 of Design Conditions: Outdoor design Conditions are as under (As per ISHRAE); Season Dry Bulb Temp.( 0 C) Wet Bulb Temp.( 0 C) Summer Monsoon Winter Daily range C 5.5 Min 10% margin over heat load calculation shall be considered for selecting capacity of Air Conditioning equipments. 5.6 Water cooled condensers shall be selected as per Basic Engineering Design Basis attached elsewhere. 5.7 For all air-conditioned buildings housing electronic equipment Chemical air filters are required to be installed in fresh air circuit. Inside quality of air shall be maintained as min ISA, G1 class within A/C area. For outdoor design conditions refer Basic Engineering Design Basis attached elsewhere. Minimum One air change per hour shall be considered for air conditioning. 5.8 Fresh Air arrangement for each building AC System; comprising of Bird Screen, Louvers, Volume Control Damper, motorised Fire Damper, Ducting, Chemical Filter with pre & fine dust filter (as per requirement), Centrifugal Fan shall be provided. 5.9 Fire Dampers shall be electrical motorised operated. Fire dampers shall be provided as per clean agent zoning. Relevant OISD norms shall be followed while deciding the location of fire dampers` Air Conditioning equipment shall be interlocked with gas/smoke detection and fire fighting system of the plant Safety factor shall be considered as minimum 12.5% in respect to Room sensible Heat and minimum 10% in respect of Room latent Heat Insulated supply air ducting shall be as per IS 655 / SMACNA complete with volume control damper, Splitter damper, guide Vanes, fire resistant flexible connection between Unit and ducting, air flow switch in main supply air ducts, duct supporting arrangement with anchor fasteners Duct mounted Electric strip finned heaters shall be provided complete with heating and safety thermostat with suitable inspection window for heater maintenance Self standing / wall mounted / audio/ visual annunciation panel for Package unit/ Air Heaters status and temperature / pressure instruments/controls as per standard Specifications.

6 DOC.No HVAC-PKG-300 DHT PROJECT Page 6 of Bidder to furnish the duct layout, while preparing duct layout purchaser s lighting layout and other relevant drawings shall be referred. Further any modification if required at site shall be done by Bidder to avoid interference, after taking proper approval 5.16 Bidder to furnish guaranteed power consumption for system. 6.0 DESIGN BASIS FOR VENTILATION S 6.1 All battery rooms shall have separate supply air fans and exhaust fans and fan motors shall be Ex.d type (gas group IIA/IIB/IIC). Minimum 12 air changes per hour of the room volume shall consider for ventilation of these rooms. Material of construction of Exhaust fans shall be suitable for fumes generated in Battery room. 6.2 For other rooms where ventilation is required like Clean Agent room in Control Building, minimum 12 air changes per hour of the room volume shall be considered for designing the exhaust system of the rooms. 6.3 Electrical (MCC Rooms) shall be ventilated. Minimum air changes to be considered for air quantity calculation shall be 12/hr. Air quantity shall also be calculated on the basis of 3 0 C temperature rise above ambient air (Taking care of the design temperature of the electrical equipment inside) and the higher of the two shall be provided. 6.4 Air intakes shall be located in non-hazardous and chemical fume free areas. 6.5 The system shall be provided with HDPE filters with frame work (minimum 90%, 10 microns), motorised CBRI certified fire dampers with frame in Supply air duct, control cable, power cable, interlocks to actuate audible alarm in case of fire, spring actuated counter weight operated pressure relief dampers with frame, bird screen, GSS air intake louvers with frame & bird protection screen, ducting with anodised aluminum grilles with aluminum angle frame, differential pressure measuring stn. across filters, manometers in space, associated civil, electrical, instrumentation, structural work & painting, inspection, performance testing. 6.6 The fans and motor noise level shall not exceed 85 dba at 1m distance from the equipment. 7.0 AIR CONDITIONING & VENTILATION EQUIPMENTS AND MATERIAL For details of Air Conditioning System & Ventilation system, refer following specifications; 6261-AA AA AA AA-340 Standard Engineering Specifications for Air conditioning system Standard Engineering Specifications for Air Handling Unit Standard Engineering Specifications for pressurization and Ventilation system Standard Engineering Specifications for Axial Fan

7 DOC.No HVAC-PKG-300 DHT PROJECT Page 7 of LIST OF SUGGESTED VENDOR 8.1 AIR CONDITIONING - CENTRAL Sub-vendors shall be as per Vendor List attached with this tender. 8.2 AIR CONDITIONING VAM Sub-vendors shall be as per Vendor List attached with this tender. 8.3 VENTILATION & PRESSURISATION Sub-vendors shall be as per Vendor List attached with this tender.

STANDARD ENGINEERING SPECIFICATION FOR VENTILATION SYSTEM HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT

STANDARD ENGINEERING SPECIFICATION FOR VENTILATION SYSTEM HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT STANDARD ENGINEERING SPECIFICATION FOR VENTILATION SYSTEM HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT JOB NO. : 6261 DOCUMENT NO. : 6261- AA-320 TEIL SPECIFICATION NO. AA-320 1 04.10.2010

More information

B. System Design and Performance Requirements

B. System Design and Performance Requirements 15625 Water Chillers This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or in notes

More information

B. ASHRAE 1991 HVAC Applications Handbook: Chapter 34--Testing, Adjusting and Balancing.

B. ASHRAE 1991 HVAC Applications Handbook: Chapter 34--Testing, Adjusting and Balancing. PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 230593 TESTING, ADJUSTING, AND BALANCING A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification

More information

Your partner for the right solution

Your partner for the right solution Your partner for the right solution Project engineering of power stations Environment protection in energy sector Equipment supplying Supervision of installation of the equipment supplied Commissioning

More information

TYP. SINGLE PLY ROOFING ROOF SHEETING BROAN VENT CAP #10 x 1" GASKETED SMS TYP. 4 SIDES 8" FRAMED CURB HVAC SYSTEMS "BASIS OF DESIGN" ROOF INSULATION R-19 WALL INSULATION R-13 LIGHTING EFFIECNCY PER STANDARDS

More information

Fiberglass Cooling Towers

Fiberglass Cooling Towers Fiberglass Cooling Towers Available in sizes from 100 to 240 tons. FC Series 700 Fiberglass Cooling Tower Available in sizes from 170 to 240 tons. No other fiberglass cooling tower comes with as many high-quality

More information

CFFWA-20-1-U Chilled/Hot Water Universal Mount Fan Coil 2-Pipe Heat / Cool Fan Coil 60,000 BTUH

CFFWA-20-1-U Chilled/Hot Water Universal Mount Fan Coil 2-Pipe Heat / Cool Fan Coil 60,000 BTUH CFFWA-20-1-U Chilled/Hot Water Universal Mount Fan Coil 2-Pipe Heat / Cool Fan Coil 60,000 BTUH Rev. 1.3 HVAC Guide Specifications Chilled and Hot Water Universal Mount Fan Coil 2-Pipe Nominal Size: 60,000

More information

ENGINEERING SERVICES

ENGINEERING SERVICES ICONS... ICONS ENGINEERING SERVICES Contact us at: Ph: (+91) 9704 038 648 E-mail: contactus@iconsengg.com Web: http:// ABOUT US A group of professionals imbibed with the power of knowledge thru many years

More information

B. Provide liquid-filled secondary substation transformers as indicated on drawings.

B. Provide liquid-filled secondary substation transformers as indicated on drawings. SECTION 26 12 13 PART 1 - GENERAL 1.01 WORK INCLUDED A. Comply with the provisions of Sections 26 05 00. B. Provide liquid-filled secondary substation transformers as indicated on drawings. 1.02 RELATED

More information

Application of Advanced Energy Technologies

Application of Advanced Energy Technologies GLOBALCON 2002 Philadelphia, Pennsylvania March 27, 2002 Application of Advanced Energy Technologies Michael K. West, Ph.D., P.E. Building Systems Scientist Advantek Consulting, Inc. www.advantekinc.com

More information

MOBILE SUBSTATIONS TRAILER AND SKID. tgood.com. Energy, Fast!

MOBILE SUBSTATIONS TRAILER AND SKID. tgood.com. Energy, Fast! MOBILE SUBSTATIONS TRAILER AND SKID tgood.com Energy, Fast! Global leader in E-House and prefabricated substation solutions PRODUCT OVERVIEW Custom configurable skid-mounted and trailer-mounted designs.

More information

Mechanical (HVAC)* * MasterFormat Specifications Division 23

Mechanical (HVAC)* * MasterFormat Specifications Division 23 40 Mechanical (HVAC)* The mechanical subcontractor (more commonly referred to as the heating, ventilation, and air conditioning, or HVAC, subcontractor) will furnish and install all equipment, ductwork,

More information

SECTION FIELD ERECTED INDUCED DRAFT COOLING TOWER

SECTION FIELD ERECTED INDUCED DRAFT COOLING TOWER PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract including general and supplementary conditions and specifications section apply to this section. B. Related Sections:

More information

SECTION COOLING TOWER

SECTION COOLING TOWER PART 1 GENERAL 1.1 SECTION INCLUDES A. Mechanical induced draft Cooling Tower B. Controls C. Ladder and handrails 1.2 REFERENCES SECTION 23 65 00 COOLING TOWER A. ANSI/AFBMA 9 - Load Rating and Fatigue

More information

Ehsan Soltani. Date of Birth: 1 Sep, 1980 Nationality: Iranian Marital Status: Married Mobile :(+98)

Ehsan Soltani. Date of Birth: 1 Sep, 1980 Nationality: Iranian Marital Status: Married   Mobile :(+98) Ehsan Soltani Date of Birth: 1 Sep, 1980 Nationality: Iranian Marital Status: Married E-mail: ehsan.soltani@gmail.com Mobile :(+98) - 912-1501764 CAREER BRIEF: Having over 15 Years Work Experience in Iran

More information

PIP PCEPA003 Process Analyzer System Field Installation Guidelines

PIP PCEPA003 Process Analyzer System Field Installation Guidelines January 2016 Process Control PIP PCEPA003 Process Analyzer System Field Installation Guidelines PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities,

More information

ACBC Floor Mounted Active Beam

ACBC Floor Mounted Active Beam Floor Mounted Active Beam The Price Floor Mounted Active Beam,, is designed for occupant comfort. It provides high cooling and heating capacities while simultaneously supplying ventilation air from a DOAS

More information

COOLING TECHNOLOGY INSTITUTE

COOLING TECHNOLOGY INSTITUTE PAPER NO: TP08-16 CATEGORY: DRY COOLING COOLING TECHNOLOGY INSTITUTE THE COST OF NOISE ROBERT GIAMMARUTI HUDSON PRODUCTS CORPORATION JESS SEAWELL COMPOSITE COOLING SOLUTIONS, LLC The studies and conclusions

More information

SECTION AIR DUCT CLEANING

SECTION AIR DUCT CLEANING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related Sections:

More information

Noise Control. Commercial, Industrial, and Environmental Products and Solutions.

Noise Control. Commercial, Industrial, and Environmental Products and Solutions. Noise Control Commercial, Industrial, and Environmental Products and Solutions www.kineticsnoise.com Commercial Duct Silencers Kinetics Noise Control offers the design and engineering assistance to integrate

More information

Kawasaki Gas Turbines-Americas Gas Turbines Power Generation Technology & Applications

Kawasaki Gas Turbines-Americas Gas Turbines Power Generation Technology & Applications Kawasaki Gas Turbines-Americas Gas Turbines Power Generation Technology & Applications Gas Turbine (GT) Technology Overview Gas Turbine Theory GT - Centrifugal Compressor FUEL INLET COMBUSTION CHAMBER

More information

MSC Guidelines for Review of Ventilation System Plans

MSC Guidelines for Review of Ventilation System Plans K. B. FERRIE, CDR, Chief, Hull Division Purpose: This Plan Review Guideline (PRG) explains the requirements for seeking plan approval of ventilation systems from the Marine Safety Center (MSC) for most

More information

5. AMCA 301 Method of Publishing Sound Ratings for Air Moving Devices. 6. AMCA 500 Test Methods for Louver, Dampers, and Shutters

5. AMCA 301 Method of Publishing Sound Ratings for Air Moving Devices. 6. AMCA 500 Test Methods for Louver, Dampers, and Shutters PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is

More information

Mobile Nitrogen Vaporizer Skid

Mobile Nitrogen Vaporizer Skid A NEWSLETTER FROM CRYOGENIC INDUSTRIES WINTER 2013 Mobile Nitrogen Vaporizer Skid ryoquip Europe recently C designed and manufactured a mobile nitrogen ISO container vaporizer skid for large flow rate

More information

List of Enquiry Items for Enquiry BAP/PUR/FGD/EQS/2014/ E dt

List of Enquiry Items for Enquiry BAP/PUR/FGD/EQS/2014/ E dt List of Enquiry Items for Enquiry BAP/PUR/FGD/EQS/2014/4231581E dt 13.03.2014 Sl.No Material Code Description Unit Qty Destination 1. RFW301290000 EMERGENCY QUENCHING SYSTEM AT GGH INLET AS PER TECHNICAL

More information

Element D Services Heating, Ventilating, and Air Conditioning

Element D Services Heating, Ventilating, and Air Conditioning PART 1 - GENERAL 1.01 OVERVIEW A. Provide a building temperature control/building automation system (BAS) for the space temperature control and monitoring of defined environmental conditions. General system

More information

Draft Indoor Air Quality Regulations

Draft Indoor Air Quality Regulations Department of Environment and Labour Occupational Health and Safety Division Draft Indoor Air Quality Regulations May, 2001 These draft regulations are being distributed for public comment. They do NOT

More information

Introduction of the latest Technology of Energy Conservation

Introduction of the latest Technology of Energy Conservation Introduction of the latest Technology of Energy Conservation --- To blue chip companies due to effective energy utilization --- September 15, 2015 Fuji Electric Co., Ltd. 1 Trends and prospects of the

More information

Energy Recovery Ventilation Equipment

Energy Recovery Ventilation Equipment ANSI/AHRI Standard 1060 (I-P) 2014 Standard for Performance Rating of Airto-Air Exchangers for Energy Recovery Ventilation Equipment Approved by ANSI on May 15, 2015 IMPORTANT SAFETY DISCLAIMER AHRI does

More information

Table of Contents. Division 2 Site Work Site Preparation Site Demolition Tree Protection Excavation, Trenching, and Backfilling for Utilities

Table of Contents. Division 2 Site Work Site Preparation Site Demolition Tree Protection Excavation, Trenching, and Backfilling for Utilities Division 1 Requirements Design and Construction Quality Campus Master Plans Texas Tech University System Operating and Building Maintenance Project Administration Historically Underutilized Business (HUB)

More information

Chapter 3.7: Cooling Towers

Chapter 3.7: Cooling Towers Part-I: Objective type questions and answers Chapter 3.7: Cooling Towers 1. The type of cooling towers with maximum heat transfer between air to water is. a) Natural draft b) Mechanical draft c) Both a

More information

Containment Booths. FOR MORE INFORMATION ON CONTAINMENT BOOTHS CALL +44 (0) OR

Containment Booths. FOR MORE INFORMATION ON CONTAINMENT BOOTHS CALL +44 (0) OR www.extract-technology.com ENGINEERED CONTAINMENT SOLUTIONS Containment Booths AT Extract Technology, we provide complete containment solutions based around an innovative range of Downflow Containment

More information

Tender for HVAC work of Library Building At IIM Ahmedabad

Tender for HVAC work of Library Building At IIM Ahmedabad Tender for HVAC work of Library Building At IIM Ahmedabad CoC, Specifications & Tender drawing Date of issue : 23/06/2017 Date of sub-mission : 18/07/2017 Tender No : IIMA/CCSP/024/2017-18 DATED-23/06/2017

More information

ARRANGEMENT AND WORKING OF MULTIPORT FLOW SELECTOR VALVE IN PRODUCTION MANIFOLD:

ARRANGEMENT AND WORKING OF MULTIPORT FLOW SELECTOR VALVE IN PRODUCTION MANIFOLD: GENERAL DESCRIPTION Crude oil well test manifold to be provide as Multiport Flow Selector (MPFS) technology. It provides a cost effective method for selecting and diverting well fluids from an individual

More information

/ Hybrid Cooling Towers

/ Hybrid Cooling Towers / Hybrid Cooling Towers Cooling Towers without visible plume / Cooling Technologies Balcke Hamon Dry Cooling Marley / Visible plume an avoidable problem / Every wet cooling tower generates a visible plume

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 12 2113 - LOUVER BLINDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Lifting Appliances of Ships and Offshore Installations

Lifting Appliances of Ships and Offshore Installations CCS Rule Change Notice For: Lifting Appliances of Ships and Offshore Installations Version: May, 2016. RCN No.1 Effective date: 19 May, 2016 Beijing CONTENTS Chapter 3 CRANES, LIFTS, RAMPS AND SELF-LOADING

More information

The following document can be provided to an Engineer, Contractor, or Owner to allow them to

The following document can be provided to an Engineer, Contractor, or Owner to allow them to MESAN series MXL Engineering Guide Specifications The following document can be provided to an Engineer, Contractor, or Owner to allow them to properly specify MESAN s MXL series Cooling Towers. 15XXX-

More information

Banyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL

Banyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL SECTION 01815 - HVAC COMMISSIONING REQUIREMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division

More information

A/E Design Deliverable Checklist

A/E Design Deliverable Checklist A/E Design Deliverable Checklist Design deliverables for the Design Development phase shall include all items listed in the Design Development column as well as those all items listed in the Schematic

More information

HIGH MAST CAMERA POLE ASSEMBLY GENERAL

HIGH MAST CAMERA POLE ASSEMBLY GENERAL 10-3.24 HIGH MAST CAMERA POLE ASSEMBLY GENERAL The Contractor must furnish and install the following equipment for high mast camera pole assembly as described herein and as shown on the plans: 1. Camera

More information

Planning for Biomed Facility Puts Energy Efficiency Under Microscope

Planning for Biomed Facility Puts Energy Efficiency Under Microscope Planning for Biomed Facility Puts Energy Efficiency Under Microscope Chilled beams, runaround-loop ERV system included May 19, 2014 By DAN VASTYAN, Common Ground, Manheim, Pa. HPAC Engineering Constructing

More information

A. This Section includes ceiling- and wall-mounted diffusers, registers, grilles and louvers.

A. This Section includes ceiling- and wall-mounted diffusers, registers, grilles and louvers. SECTION 23 37 13 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

Performance Efficiency Standard for Evaporative Cooling Equipment

Performance Efficiency Standard for Evaporative Cooling Equipment Industry Recommendation / Code of Good Practice 9/12-2016 Performance Efficiency Standard for Evaporative Cooling Equipment First Edition Published on 11 October 2016 by,,, Belgium - The European Committee

More information

EC medium pressure axial fans.

EC medium pressure axial fans. EC medium pressure axial fans. The efficient system solution. The engineer s choice GreenTech EC technology in a new dimension. Thanks to these new new axial axial fans, fans, our our highly highly efficient

More information

INDIA HABITAT CENTRE New Delhi

INDIA HABITAT CENTRE New Delhi INDIA HABITAT CENTRE New Delhi Tender For Renovation of Exhaust Air Ducting Works in Basements Date: January, 2014 Prepared by Sterling India Consulting Engineers New Delhi, India TABLE OF CONTENTS S.No.

More information

FACILITIES MAINTENANCE WORKER

FACILITIES MAINTENANCE WORKER FACILITIES MAINTENANCE WORKER Summary Statement: Under supervision, is responsible for performing routine building maintenance tasks and assisting Building Maintenance Supervisor with the performance of

More information

Modular Chiller Plants A GLOBAL LEADER IN ENERGY SOLUTIONS

Modular Chiller Plants A GLOBAL LEADER IN ENERGY SOLUTIONS Modular Chiller Plants A GLOBAL LEADER IN ENERGY SOLUTIONS A B O U T S tellar Energy is a global leader in the design, construction, fabrication, installation, and servicing of a range of energy systems,

More information

We are now interested to do a project of Down Hill Conveyor System for our Indian customer : A New, 7 MTPA Iron Ore design

We are now interested to do a project of Down Hill Conveyor System for our Indian customer : A New, 7 MTPA Iron Ore design ISG/DHC-001 2 nd April 2010 ASSOCIATE`S CONVEYOR SYSTEM 1.SYNOPSIS: ASSISTANCE FOR DOWN HILL BHEL, Industrial System Group, Bangalore proposes to do DOWNHILL CONVEYOR SYSTEM for Indian Mining Industries,

More information

Innotech is a registered Trademark of Mass Electronics Pty Ltd Copyright 2013 Mass Electronics Pty Ltd

Innotech is a registered Trademark of Mass Electronics Pty Ltd Copyright 2013 Mass Electronics Pty Ltd CHILLED WATER PRIMARY SECONDARY & THERMAL ENERGY STORAGE DIGITAL CONTROL SYSTEM FUNDAMENTALS Presented by : Ben Macdonald QLD Sales Manager Innotech Control Systems Australia www.innotech.com.au Innotech

More information

Large University Central Chiller Plant Design Considerations

Large University Central Chiller Plant Design Considerations Carrier Engineering Newsletter Volume 5, Issue 3 Large University Central Chiller Plant Design Considerations Large campus chilled water plants have unique constraints and need careful evaluation for successful

More information

General Specifications for HVAC System Cleaning

General Specifications for HVAC System Cleaning General Specifications for HVAC System Cleaning Part 1 Special Provisions 1.01 Qualification of the HVAC System Cleaning Contractor (A) Membership: The HVAC system cleaning contractor shall be a member

More information

DANVEST POWER UNIT. with special Low Load Unit for wind-diesel power stations

DANVEST POWER UNIT. with special Low Load Unit for wind-diesel power stations DANVEST POWER UNIT with special Low Load Unit for wind-diesel power stations Controls weak or isolated grids - and gives top power quality extremely low fuel consumption and maximum exploitation of renewable

More information

A GUIDE TO REACH SYSTEM RELIABILITY. Commercial HVAC Buyers Guide

A GUIDE TO REACH SYSTEM RELIABILITY. Commercial HVAC Buyers Guide A GUIDE TO REACH SYSTEM RELIABILITY Commercial HVAC Buyers Guide How to confidently select your HVAC contractor, compare options and quotes, and enjoy system reliability. If you are reading this document,

More information

Industrial Application of Thermal Energy Harvesting

Industrial Application of Thermal Energy Harvesting GE - Bently Nevada Industrial Application of Thermal Energy Harvesting Dr. Thomas Kafka GE Sensing & Inspection Technology GmbH Frankfurt, Germany 1 GE - Bently Nevada Content: Wireless data collection

More information

COMMERCIAL LOAD ESTIMATING. Load Estimating Level 3: Block and Zone Loads. Technical Development Program

COMMERCIAL LOAD ESTIMATING. Load Estimating Level 3: Block and Zone Loads. Technical Development Program COMMERCIAL LOAD ESTIMATING Load Estimating Level 3: Block and Zone Loads Technical Development Program Technical Development Programs (TDP) are modules of technical training on HVAC theory, system design,

More information

This document also describes the basis on which building permit fees should be calculated.

This document also describes the basis on which building permit fees should be calculated. 1/6 1.0 PURPOSE This specification outlines when a Building Permit is required pursuant to the Building Code Act and its Regulations. The Building Code Act prescribes that each municipality is responsible

More information

SECTION 16496A MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number

SECTION 16496A MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number PART 1 GENERAL 01 02 03 04 SCOPE Furnish and install Manual Transfer Switches (MTS) and

More information

ISO INTERNATIONAL STANDARD. Petroleum and natural gas industries Packaged reciprocating gas compressors

ISO INTERNATIONAL STANDARD. Petroleum and natural gas industries Packaged reciprocating gas compressors INTERNATIONAL STANDARD ISO 13631 First edition 2002-08-01 Petroleum and natural gas industries Packaged reciprocating gas compressors Industries du pétrole et du gaz naturel Unités de compresseurs alternatifs

More information

Forced Draft Decarbonators. Degasification

Forced Draft Decarbonators. Degasification Forced Draft Decarbonators Degasification Forced Draft Decarbonator When do you need it? What is it? How does it work? In Ion Exchange Demineralizer Systems, Forced Draft Decarbonators are located between

More information

Transform your HVAC performance. Good for your comfort, for the environment and for your bottom line

Transform your HVAC performance. Good for your comfort, for the environment and for your bottom line Transform your HVAC performance Good for your comfort, for the environment and for your bottom line TRANSFORMING YOUR HVAC SYSTEM IMPULS-e is a portfolio of solutions from Trane which uses advanced technology

More information

PAINT BOOTHS GENERAL PURPOSE

PAINT BOOTHS GENERAL PURPOSE PAINT BOOTHS GENERAL PURPOSE 1 INDUSTRY-LEADING PRODUCTS With precise contamination control and premium angled ceiling hip lights, General Purpose Paint Booths from Global Finishing Solutions (GFS) enable

More information

SCOPE OF WORK FOR STEEL SHEDS OF FIRE WATER PUMP HOUSE & PRODUCT PUMP HOUSE

SCOPE OF WORK FOR STEEL SHEDS OF FIRE WATER PUMP HOUSE & PRODUCT PUMP HOUSE Doc No: 254624-400-SW-CIV-015 Rev: Page 1 of 7 SCOPE OF WORK FOR STEEL SHEDS OF FIRE WTER PUMP HOUSE & PRODUCT PUMP HOUSE Hindustan Petroleum Corporation Ltd Visakha Dispatch Station VR-TP rea, Naval Base

More information

ASHRAE Chapter Meeting HVAC Noise & Vibration Control Specifications & Best Practices

ASHRAE Chapter Meeting HVAC Noise & Vibration Control Specifications & Best Practices ASHRAE Chapter Meeting HVAC Noise & Vibration Control Specifications & Best Practices Industrial Presented By OEM Architectural Noise & Vibration Control, Inc. 610-863-6300 www.brd-nonoise.com HVAC Marine

More information

Pioneer Forced Draft Cooling Tower Specifications

Pioneer Forced Draft Cooling Tower Specifications Delta Cooling Towers, Inc. 41 Pine Street P.O. Box 315 Rockaway, New Jersey 07866-0315 Telephone 973.586.2201 Fax 973.586.2243 www.deltacooling.com sales@deltacooling.com Pioneer Forced Draft Cooling Tower

More information

Check-List of General Building Services

Check-List of General Building Services Check-List of General Building Services AREAS Land Area 2 Acres Usage IT / ITES plus facilities Build up Area Office space 2,35,001 sq.ft. plus double basement of 1,03,374sq.ft. Floor Plate 30,000sq.ft

More information

A. Drawings and general provisions of the Contract, including General Conditions Specification Sections, apply to this section.

A. Drawings and general provisions of the Contract, including General Conditions Specification Sections, apply to this section. Page 1 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions Specification Sections, apply to this section. 1.2 SUMMARY A. The shade structure

More information

Chilled Beams. The new system of choice?

Chilled Beams. The new system of choice? Chilled Beams The new system of choice? Presented By: Kevin M. Pope P.E. Jason Leffingwell Hammel Green And Abrahamson, Inc. and Ken Bauer, P.E., LEED AP Butters-Fetting Co., Inc. History of Chilled Beams

More information

SPACE TYPE: PHYSICAL FITNESS (EXERCISE ROOM)

SPACE TYPE: PHYSICAL FITNESS (EXERCISE ROOM) SPACE TYPE: PHYSICAL FITNESS (EXERCISE ROOM) Construction Criteria The unit costs for the Physical Fitness Center (Exercise Room) space type are based on the construction quality and design features in

More information

Fenestration Components: Mechanical Summary. Water heater energy factor: Ef Fuel type: Gas Electric Other

Fenestration Components: Mechanical Summary. Water heater energy factor: Ef Fuel type: Gas Electric Other This information must be on the drawing documents not attached to plans. The following Compliance statements must be on the drawings: 2009 International Energy Conservation Code Statement of acknowledgement

More information

Great Ocean Rd Ice Creamery

Great Ocean Rd Ice Creamery Great Ocean Rd Ice Creamery BCA Section J - JV3 Compliance Report Revision: 01 Job No: 2171 Date: 7 July 2015 ADP Consulting Pty Ltd Level 10, 10 Queens Rd, Melbourne Vic 3004 www.adpconsulting.com.au

More information

CI/SfB (57.7) 1st edition

CI/SfB (57.7) 1st edition CI/SfB (57.7) 1st edition Vent-Axia Sentinel Multivent Wholehouse Mechanical Extract Ventilation System Ventilation Lo-Carbon Energy saving solutions Sentinel Multivent continuous mechanical extract ventilation,

More information

DESIGN SPECIFICATION FOR FOUNDATIONS

DESIGN SPECIFICATION FOR FOUNDATIONS FOR HINDUSTAN PETROLEUM CORPORATION LTD. VISAKH REFINERY DHT PROJECT JOB NO. : 6261 DOCUMENT NO. : A-6261-110-006 TOTAL NO. OF PAGES: 11 (INCLUDING THIS PAGE) 0 16-11-2009 FOR APPROVAL

More information

FABRIC EXPANSION JOINTS. Technical Brochure

FABRIC EXPANSION JOINTS. Technical Brochure FABRIC EXPANSION JOINTS Technical Brochure FABRIC EXPANSION JOINTS Fabric expansion joints have found a wide range of applications, in all industry branches due to their adaptability for different conditions:

More information

Detailed Requirements Document (DRD) Rail Engineering Advanced Technician Level 4 Electrification Knowledge & Skills Content

Detailed Requirements Document (DRD) Rail Engineering Advanced Technician Level 4 Electrification Knowledge & Skills Content Detailed Requirements Document (DRD) Rail Engineering Advanced Technician Level 4 Electrification Knowledge & Skills Content Purpose The purpose of this Detailed Requirements Document (DRD) is to provide

More information

COMPLETE REVISION April Process Industry Practices Piping. PIP PNC00004 Piping Stress Analysis Criteria for ASME B31.

COMPLETE REVISION April Process Industry Practices Piping. PIP PNC00004 Piping Stress Analysis Criteria for ASME B31. April 2012 Process Industry Practices Piping PIP PNC00004 Piping Stress Analysis Criteria for ASME B31.3 Metallic Piping PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost

More information

TM Series Cooling Tower Specification

TM Series Cooling Tower Specification 1.0 Cooling Tower TM Series Cooling Tower Specification 1.1 General: Furnish and install factory-assembled, induced draft, counterflow cooling tower(s) with vertical air discharge conforming in all aspects

More information

Telecommunication Spaces

Telecommunication Spaces Telecommunication Spaces October 19, 2016 Page 1 Revision History Telecommunication Spaces Standard Effective Date Email Version Contact Phone OIT-TS strevena@csustan.edu 1.0 Stan Trevena 209.667.3137

More information

Full-Scope Commissioning for High-Quality Buildings

Full-Scope Commissioning for High-Quality Buildings Full-Scope Commissioning for High-Quality Buildings Pieter L. van der Mersch, PE, QCxP University of Colorado Boulder 21 st National Conference on Building Commissioning AIA Quality Assurance The Building

More information

Indoor Air Quality Improvement in a School Building in Delhi

Indoor Air Quality Improvement in a School Building in Delhi Indoor Air Quality Improvement in a School Building in Delhi Maija Virta #1, Suhaas Mathur #1 # Santrupti engineers Private Limited 1083, 35 th D Cross, 4 th T Block, Jayanagar, Bangalore 560041, India

More information

AIRCOOL VENTILATORS FURTHER INFORMATION

AIRCOOL VENTILATORS FURTHER INFORMATION .................................................. CI/SfB (57.7) Xy Uniclass L7563 January 2015 FURTHER INFORMATION................................................................... Services Passivent

More information

REV. 9/08. Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms

REV. 9/08. Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms REV. 9/08 Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms SKYTRON MOUNTING STRUCTURES for Ceiling Mounted Equipment Foreword Skytron s objective is to provide a program and guideline to assist

More information

Information Delivery Manual (IDM)

Information Delivery Manual (IDM) Piping Engineering - Confluence http://idm.buildingsmart.no/confluence/display/idm/piping+engineering?decorator=printable 1 af 2 11-09-2011 19:21 Information Delivery Manual (IDM) Added by Jeffrey Wix,

More information

Retro-Commissioning for Existing Facilities

Retro-Commissioning for Existing Facilities Retro-Commissioning for Existing Facilities Tom Meyer Director, Technical Programs National Environmental Balancing Bureau 8575 Grovemont Circle Gaithersburg, Maryland 20877 (301) 977-3698 www.nebb.org

More information

CITY OF RICHMOND PINE CAMP COMMUNITY CENTER ROOF REPLACEMENT PROJECT RCS PROJECT NO

CITY OF RICHMOND PINE CAMP COMMUNITY CENTER ROOF REPLACEMENT PROJECT RCS PROJECT NO SECTION 01010 - SCOPE OF WORK PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General provisions of Contract, General Conditions and Technical Specification Sections, apply to this Section. 1.02 PROJECT DESCRIPTION

More information

DIVISION 11 - EQUIPMENT FOOD SERVICE EQUIPMENT LABORATORY FUME HOODS. A. Design Considerations

DIVISION 11 - EQUIPMENT FOOD SERVICE EQUIPMENT LABORATORY FUME HOODS. A. Design Considerations DIVISION 11 - EQUIPMENT 11400 FOOD SERVICE EQUIPMENT A. Design Considerations 1. The A/E shall use the services of a food service equipment specialist in preparation of kitchen areas and other food preparation

More information

Trends and drivers in the Finnish ventilation and AC market

Trends and drivers in the Finnish ventilation and AC market Trends and drivers in the Finnish ventilation and AC market Jarek Kurnitski, D.Sc. Docent Helsinki University of Technology Finnish Society of Indoor Air Quality and Climate, FiSIAQ 1 Contents Indoor climate

More information

Blackstone: flexible and environmentally friendly power plant

Blackstone: flexible and environmentally friendly power plant May-June 2002 Turbomachinery Blackstone: flexible and environmentally friendly power plant INTERNATIONAL Two single shaft combined cycle blocks - each with centrally-mounted generator and SSS Clutch Blackstone:

More information

Oki (High Pressure Boiler Plant)

Oki (High Pressure Boiler Plant) Bharat Heavy Electricals Limited 1717TC.1 Oki (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU, INDIA An ISO 9001 MATERIALS MANAGEMENT / CAPITAL EQUIPMENT Company ENQUIRY Phone: +91 431

More information

BUSWAY LOW VOLTAGE (POW-R-WAY III) SECTION SECTION 16466

BUSWAY LOW VOLTAGE (POW-R-WAY III) SECTION SECTION 16466 BUSWAY LOW VOLTAGE (POW-R-WAY III) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein

More information

District Cooling Sustainable Design. Presented by George Berbari CEO of DC PRO Engineering

District Cooling Sustainable Design. Presented by George Berbari CEO of DC PRO Engineering 2016 District Cooling Presented by George Berbari CEO of DC PRO Engineering District Cooling Brief History & Future Central Chilled Water plants existed in the Middle East as early as the 1960 s. Few examples

More information

Sampling. Stationary Portable. Sampling. Sewage Treatment. Municipal Sewerage Systems. Water Protection Control

Sampling. Stationary Portable. Sampling. Sewage Treatment. Municipal Sewerage Systems. Water Protection Control Sampling Stationary Portable Sampling is an important factor for the compliance with required regulations and efficient operation. It forms the basis for continuous monitoring objectives and criteria,

More information

Energy Conservation Best Know Methods Phil Naughton

Energy Conservation Best Know Methods Phil Naughton Energy Conservation Best Know Methods Phil Naughton Why do we need energy reduction? Need for sustainable development Public pressure Customers and NGOs Legislative trends (EuP, Kyoto Protocol) Corporate

More information

Nilan VPL Active heat recovery and cooling (air/air)

Nilan VPL Active heat recovery and cooling (air/air) M a r k e t l e a d i n g c o m m e r c i a l a n d d o m e s t i c v e n t i l at i o n w i t h h e at r e c o v e r y Nilan 31-125 Active heat recovery and cooling (air/air) Nilan 31-125 Commercial ventilation

More information

Geothermal Power Plant

Geothermal Power Plant Geothermal Power Plant The Tokyo Electric Power Co., Inc., Japan Hachijo-jima Geothermal Power Plant 3,300kW 0A3-E-009 Outline All equipment and system except for the civil work and geothermal wells were

More information

C. ASSE 1013 Performance Requirements for Reduced Pressure Principle Backflow Preventers.

C. ASSE 1013 Performance Requirements for Reduced Pressure Principle Backflow Preventers. PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-23 71 19 (January 2008) Change 1-08/15 ---------------------------- Preparing Activity: USACE Superseding UFGS-23 71 19 (July 2007) UNIFIED FACILITIES GUIDE SPECIFICATIONS

More information

ENVIRONMENTAL NOISE CONTROL FOR SEMICONDUCTOR MANUFACTURING FACILITIES

ENVIRONMENTAL NOISE CONTROL FOR SEMICONDUCTOR MANUFACTURING FACILITIES Presented at Inter-Noise 99 The 1999 Congress and Exposition on Noise Control Engineering December 8, 1999, Fort Lauderdale, Florida ENVIRONMENTAL NOISE CONTROL FOR SEMICONDUCTOR MANUFACTURING FACILITIES

More information

Evergreen Project Implementation Plan Instructions Low Income Housing Tax Credit Program

Evergreen Project Implementation Plan Instructions Low Income Housing Tax Credit Program Evergreen Project Implementation Plan Instructions Low Income Housing Tax Credit Program The following table provides a brief description of the documentation that will be required of successful LIHTC

More information

PAINT BOOTHS LARGE EQUIPMENT

PAINT BOOTHS LARGE EQUIPMENT PAINT BOOTHS LARGE EQUIPMENT 1 THE FINISHING TOUCH A flawless paint finish can make a product stand out from the rest. With precise contamination control and excellent lighting, Large Equipment Booths

More information