All panels can be supplied in a range of styles, to suit the applications pictured below.

Size: px

Start display at page:

Download "All panels can be supplied in a range of styles, to suit the applications pictured below."

Eunice Hodges
6 years ago
Views:

1 Evolution Radiant panel system LPHW up to 90 C Suspended ceiling grid or soffit mounting Vertical wall surface mounting Standard widths 150mm to 900mm 1

Description Introduction Evolution by Dunham-Bush is an architectural radiant panel system, ideal for application in light industrial or commercial buildings.

2 Description Introduction Evolution by Dunham-Bush is an architectural radiant panel system, ideal for application in light industrial or commercial buildings. It is designed for use with low temperature hot water on either constant or variable temperature circuits. The unique heating effect from Evolution radiant panels will create comfort conditions at lower design air temperatures. Room occupants are heated directly, without the need to heat the air surrounding them. Evolution can be installed in suspended ceilings, directly onto wall or ceiling surfaces or hung from drop rods. It is modular, giving the system designer great flexibility in selecting panels for any application. The standard finish is white polyester powder, but other finishes are available from the RAL or BS 4800 ranges. Authority It is accepted practice and policy at Dunham-Bush to maintain exceptional standards in engineering and quality. To this end, Dunham-Bush operates a quality system and is registered as a company of assessed capability to BS EN ISO 9001 : A one tube Evolution radiant panel consists of an aluminium alloy extruded plank, which has a plane radiating surface on one side and a semi-circular groove on the opposite side. A 15mm O.D. copper tube is retained in the groove by an extruded tube clamp, which completely encapsulates the tube. Planks are assembled and interlocked, side by side, to produce multi-tube panels. Standard Range The range consists of one, two, four and six tube panels, in nominal lengths of 600mm to 3000mm, and in various tube configurations, as illustrated in the panel diagrams. All panels can be supplied in a range of styles, to suit the applications pictured below. Style CG for suspended ceiling grid with lay-in tiles Style CS for ceiling surface or soffit mounting Style FS for suspension from roof/ soffit or steelwork Style WS for mounting onto vertical walls 2

Style CG (Ceiling Grid) For installation into suspended ceiling

Can also be installed into solid plasterboard ceilings with

Style FS (Free Suspended) For installation into open roof or

Can be hung from threaded drop rods or suspension wire systems.

3 Style CG (Ceiling Grid) For installation into suspended ceiling grids with lay-in type tiles. Can also be installed into solid plasterboard ceilings with perimeter trim. Style FS (Free Suspended) For installation into open roof or celiing voids. Can be hung from threaded drop rods or suspension wire systems. Style CS (Ceiling Surface) Surface mount option from solid ceiling of soffit. Fully accessible from below. Style WS (Wall Surface) Vertical wall surface mount option. Can be installed at an angle in a cornice configuration. 3

4 Style CG General Arrangement 4

5 Style CG Panel Types 5

6 Style CG Panel Runs 6

7 Style CG Sections - 1 Tube & 2 Tube Panels 7

8 Style CG Sections - 4 Tube & 6 Tube Panels 8

9 Style CG Suspension Locations 9

10 Style CG Panel Connections 10

11 Style CS General Arrangement 11

12 Style FS General Arrangement 12

13 Style WS General Arrangement 13

14 Style CS, FS & WS Panel Types 14

15 Style CS, FS & WS Panel Runs 15

16 Style CS, FS & WS Sections - 1 Tube & 2 Tube Panels 16

17 Style CS, FS & WS Sections - 4 Tube & 6 Tube Panels 17

18 Style FS Suspension Locations 18

19 Style CS, FS & WS Panel Connections 19

20 Performance Total heat outputs, Watts per metre of nominal panel length Mean water ( C) Ambient air temperature ( C) Rated Thermal Output (W/m) Styles CG CS & FS (BS EN 14037) Style WS (BS EN 442) 1T 2T 4T 6T 1T 2T 4T 6T Performance equation where Q = rated thermal output per unit area (W/m²) Styles CG CS & FS (BS EN 14037) Style WS (BS EN 442) Q = K d DT n K d n Notes 1. Thermal outputs are rated as defined in the relevant standard and are both radiant and convective. 2. Styles CG CS and FS; ~60% or total output is radiant; Style WS; ~53% of total output is radiant. 3. Outputs for Styles CG CS and FS are rated to BS EN Parts 1, 2 and 3, BS EN applies for horizontally mounted panels only. 4. Outputs for Style WS are rated to BS EN 442 Part Performance equation Q = K d DT n Where Q = rated thermal output (W/m 2 ) K d = output factor, n = output exponent DT = mean water temperature less ambient air temperature (K) 20

21 Notes: 1. Where a single panel type ED is used, the minimum water mass flow rate should not be less than kg/s, to obtain the rated output. 2. Where two or more panels are joined together to form a run, the minimum mass flow rates listed in the table must be observed, to prevent air locking. 3. The circuit length for any run can be calculated from the number of tubes per panel, the lengths and panel types and the quantity of panels being used. The pressure loss per circuit can be obtained from the graph below, which includes a nominal allowance for bends and fittings. Minimum water mass flow rates Circuit length L metres Minimum flow rate kg/s L > L > L L < The maximum recommended flow rate per circuit is 0.141kg/s (1.0m/s). Approximate dry masses of Evolution (kg) 1 Tube 2 Tube 4 Tube 6 tube Mass per Style Style Style Style metre (kg) CG CS,FS,WS CG CS,FS,WS CG CS,FS,WS CG CS,FS,WS Note: Masses exclude additional angle brackets used on wall mounted applications Pressure drop (Pa/m) per tube or circuit; check layout drawing for no. of circuits. 21

Application Comfort conditions It is recommended that for radiant heating systems, comfort conditions are achieved when dry-bulb air temperature is slightly lower than mean radiant temperature.

22 Application Comfort conditions It is recommended that for radiant heating systems, comfort conditions are achieved when dry-bulb air temperature is slightly lower than mean radiant temperature. This difference between the two temperatures will result in the desired operative temperature. The heat loss of the room under consideration may be calculated in accordance with CIBSE Guide A Environmental Design. Evolution is intended for operation with LTHW. The maximum recommended flow temperature is 90 C. Selection The following guidelines are to assist the designer in deciding the best layout for Evolution 1. The total heat load of the room must be calculated in accordance with recognised practice. Heat loads should be calculated using the internal design air temperature (dry bulb). However, the internal design air temperature can be reduced since mean radiant temperatures are elevated by radiant heating. 2. The total heat load should be divided by the total heat output per metre,. This will then give the require overall length of 1 tube, 2 tube, 4 tube or 6 tube radiant panels. Vertical panels will give greater heat output, which arises from greater convective heat transfer from the panel surface. 3. The run layout should then be decided, and is best set out on a layout plan. Radiant panels should be located around the outside perimeter of the room, particularly near windows. This will counteract disproportionately high heat losses. 4. There is no maximum mounting height for Evolution. However, when mounting heights exceed 4m, the heat load should be adjusted to additional losses of radiant heat incident on the walls. 5. There is no minimum mounting height for Evolution. As a rule of thumb, mounting heights should be not be lower than 2.4m. Contact Dunham-Bush for further advice on mounting heights and mean radiant temperatures. 6. Expansion panels must be used for longer panel runs, using the following guidelines :- 4 tube panels one expansion joint every 6m 6 tube panels one expansion joint every 3m 7. Ceiling Grid Applications Evolution Style CG is designed to fit into conventional lay-in tile ceiling grids; panel dimensions have been optimised so that panel edges are concealed by standard ceiling grid T-bars - typically 15mm or 24mm. 8. Plaster Board Ceiling Applications Evolution Style CG can be installed flush into a plasterboard ceiling, with typical edge trims by others; builders work should include access for commissioning and maintenance. 9. Surface Applications For other types of ceiling, Style FS or Style CS panels may be more appropriate. Style WS panels are designed for vertical wall surface applications. Evolution style FS installed into a pitched ceiling of community centre 22

23 Solid Ceilings Detail of Evolution Style CG installed flush mounted into plasterboard ceiling Evolution Style CS installed into a pitched plasterboard ceiling 23

24 Special Installations Special angle bracket installation for Evolution Style WS Evolution Style WS installed onto special angle brackets (angle to suit project requirement) 24

Engineering Specification The Evolution radiant heating panels shall be manufactured by Dunham- Bush Limited, Downley Road, Havant, Hampshire PO9 2JD.

Style CG ceiling grid Style CS ceiling surface Style FS freely suspended Style WS wall surface Panel types Evolution radiant panel types shown in the panel types diagram, suitable for the hydraulic

25 Engineering Specification The Evolution radiant heating panels shall be manufactured by Dunham- Bush Limited, Downley Road, Havant, Hampshire PO9 2JD. The style, panel types, lengths and quantities shall be as detailed in the schedule or as shown on the drawings. Styles Evolution radiant panel style shall be suitable for the selected application. Style CG ceiling grid Style CS ceiling surface Style FS freely suspended Style WS wall surface Panel types Evolution radiant panel types shown in the panel types diagram, suitable for the hydraulic circuit specified and shall be selected from the following list: Type EA standard panel Type EB end panel Type EC connection panel Type ED single panel Type EE expansion panel Type EF multi-circuit panel 22mm conn. Type EG dummy panel (no tubes) Type EH15 flow panel 15mm conn. Type EH22 flow panel 22mm conn. Type EJ15 return panel 15mm conn. Type EJ22 return panel 22mm conn. Composition Evolution radiant panels shall comprise one, two, four or six extruded aluminium alloy planks, which shall have a plane radiating surface on one side and semi-circular groove on the opposite side. A 15mm O.D. copper tube to EN1057, shall be retained in the groove by extruded tube clamps, which shall completely encapsulate the tube. The edges of the extrusion shall be tongued and grooved. Multi tube panels shall be assembled from extruded planks, interlocked side by side, securely joined by galvanised braces. Tube joints shall be soft soldered and panels shall be fitted with manual air vents, as appropriate to the panel circuitry. Where two or more panels are to be joined together, slip couplings shall be provided at tube joints. Expansion panel type EE shall be supplied with expansion hoses, as appropriate to the number of tubes. Style CG Evolution panels shall be fitted with suspension brackets. Where two or more panels are to be joined together, connector plates and joint strips shall be supplied. 50mm thick mineral wool or equal, aluminium foil faced thermal insulation, shall be provided loose for site fitting. Styles CS,FS and WS Evolution panels shall be supplied with top and bottom side rails for fixing together on site. Finish All panels and accessories shall be degreased before powder coating, colour RAL 9010, 30% gloss. Site test and working pressure Maximum cold test pressure 10.5 bar gauge, Maximum working pressure 7.0 bar gauge at 90 C, Note: higher pressures can be accommodated using silver soldered joints. Consult Dunham-Bush for details. Style CG, ceiling grid Style CG, ceiling grid Panel nominal lengths All styles and types, except corners. Panel nominal lengths shall be as detailed in the following list: 600, 900, 1000, 1200, 1500, 1800, 2000, 2100, 2400, 2500, 2700 and 3000mm. 25

26 Construction Handling The purchaser is responsible for offloading. Radiant panels can usually be lifted by two persons, but longer panels may require a third person providing support in the middle. Panels and accessories are usually palletised and shrinkwrapped, so fork lift truck or similar form of lifting equipment is required. Care should be taken to ensure panels are not dropped or suffer impact in any circumstances. Storage Radiant panels should be stored under clean, dry indoor conditions. Any packaging should not be removed until panels are ready for installation, unless damage in transit is suspected. Note the purchaser must examine the panels promptly upon receipt and any claims for damage will only be accepted if, at the time of delivery, the delivery note is endorsed with a note detailing the damage and countersigned by the transport company. Each panel may be marked with a stencil reference if specified on the order. Preparation Extensive modification to the building fabric should not normally be necessary. However, proper provision for fixings must be arranged. The structure to which the panels are to be fixed must be fit for purpose and be capable accepting drop rods or similar suspension fixings. Allowance must be made for the panels to expand freely. Style CG (ceiling grid) panels should be suspended from M6 drop rods with washers and nuts. Other suspension methods may be used. Contact Dunham-Bush for guidance. Styles CS (ceiling surface) and WS (wall surface) bottom side rails and back side rails should be screwed or bolted to a sound, flat horizontal or vertical surface (fixings not supplied). Style FS (free suspended) panel is suspended directly from drop rods or similar (not supplied). Note : It is important to coordinate the installation of panels with other trades, especially when Evolution radiant panels are to interface with other fittings such as ceilings and soffits. Pipework Connections Evolution radiant panels are supplied with pipe circuitry prepared at factory hence only flow, return and panel-joint connections are required. All panels will accept fittings for 15mm or 22m copper tube. It is recommended that connection pipework is given sufficient flexibility to allow for thermal expansion. Installation Radiant panels are supplied with assembly and installation Instructions, which provide full details on installing, connecting and commissioning radiant panels. Additional copies are available upon request. N.B. All panels are fitted with protective film on the radiating surface, which should not be removed until installation is complete and there is no risk of damage. Style CS, FS and WS panels are supplied in kit form and require assembly on site. 26

27 Supply Prices Dunham-Bush do not issue price lists, but will be pleased to provide a written quotation upon request. All quotations are normally prepared by a member of our national network of sales agents and representatives. For further details, please contact Dunham-Bush head office in Havant, Hants. Conditions of sale Standard conditions of sale are included on the reverse of all order acknowledgements. Further copies are available upon request. Availability Evolution radiant panels are supplied direct from the Dunham-Bush factory in Havant. All panels are made to order, and availability can vary with demand and should therefore be checked at the time of ordering. Contact a Dunham- Bush sales agent/ representative for typical lead times. Packaging Evolution radiant panels are packed for storage in dry, indoor conditions. If specified, each panel will be marked with its own unique stencil reference for on-site identification. Ordering To ensure the rapid processing of your order, please refer to the relevant quotation and appropriate correspondence. Please send your order directly to the Dunham-Bush sales agent/representative who provided the quotation. Dunham-Bush will prepare a detailed layout drawing of the proposed installation for approval prior to manufature. 27

28 Manufacturer reserves the right to change any product specification without notice Dunham-Bush Ltd Downley Road Havant Hants PO9 2JD Tel Fax B MAY

system 200/205 modular hook-on tiles (concealed grid) SAS International +44 (0)

metal ceilings system 200/205 modular hook-on tiles (concealed grid) SAS International +44 (0) 118 929 0900 www.sasint.co.uk system 200 information System Description SAS System 200 is a range of square,