In-Wall Tank and Bowl Carrier System With Dual Flush Technology Geberit Model No Flush Volume: 1.6 / 0.8 GPF / 3.

Size: px

Start display at page:

Download "In-Wall Tank and Bowl Carrier System With Dual Flush Technology Geberit Model No Flush Volume: 1.6 / 0.8 GPF / 3."

Samuel Martin
6 years ago
Views:

1 D (00) In-Wall Tank and owl Carrier System With Dual Flush Technology Geberit Model No Flush Volume:.6 / 0.8 GPF /.0 LPF

2 Product Data Product Specifications - For installing -hole stud mounted wall-hung washdown water closet fixtures with rear water inlet and waste outlet - For 6 GPF (6 LPF) single flush or.6/0.8 GPF (6/ LPF) dual flush fixtures - For installation within or in front of drywall panels - For installation in front of solid walls. - Fits within minimum ½" (90) framing wall or plumbing chase - djustable for fixture seat heights from 5" to 9" (8 to 48) - " water supply - For flush actuator plates Sigma, olero, Samba, Mambo, Tango, Rumba Features - ET water consumption Dual-flush.6/0.8 GPF (6/ LPF) gives effective flush volume of. GPF (4 LPF) - nti-siphon fill valve - Impact resistant high density polyethylene (DPE) tank, insulated to prevent condensation - 6-gauge, powder-coated, structural steel tubing rated to 880 lbs. (400 kg) without damage to finished wall or carrier unit - Includes installation and rough-in materials Warranty Limited lifetime warranty on tank and carrier 0-year warranty on fill valve and flush valve One-year warranty on actuator flush panels. Standards In compliance with: - SME:.6.,.9.5, NSI Z4.4 - CS 5. - NSI/SSE 00 - IPMO PS-50 - UNR / UNR-ET - Meets or exceeds the WaterSense ET and SME.9. specifications when installed in combination with appropriate matching fixture. For a list of certified combinations, refer to For optional washlet water supply stop 7"-" typical 0-4¾" /8" ¼" ½" NPT 6¼" 7 /8"/ 9" 5½" ref 5½" 6½"- 40½"** 4"-46"** ½" For optional washlet electrical outlet box For ½" max. wall thickness Vertical drainage only 5 /8"-" 6½"-40½"** Seated heigth+½" 4½" ¾"-½" 5"-9"** Seated heigth 0-4¾" ** assumes a typical seat thickness of " and a distance from fixture rim to mounting rod centers of " For 5½" min. wall thickness For R, L and vertical drainage 5½" ½" Material Determination Recommended material for wall surface construction: - Gypsum / green board - Cement board - Tile backer board - Ceramic tile surface 0-4¾" Minimum wall material thickness ¾" (0 mm). D D Compliant

3 Installation Installation Requirements To install carrier, a minimum ½" wall is required. x 6" wood frame or metal frame construction is recommended. Studs must be placed ¼" apart (clearance) where carrier will be positioned inside the wall. Prepare These values are needed to set proper frame height at roughing in: : Finished Floor eight FS: Finished Seated eigth ST: Seat thickness, based on seat model RT: Distance from fixture rim to mounting centers, based on ceramic model : Frame eigth, subject to conditions below: = FS - RT - ST + " (790) These values are not needed at roughing in, but may be useful as alternate references: FV: Flush Valve eight (see below) R: Rod eight, based on ceramic model and FS (see below) D: Drain outlet, based on ceramic model and FS (see below) For convenience, values for a typical situation are included in the following chart: FOR REFERENCE Finished Seat eight (FS) Frame eight () 4 /8 4 /8 44 /8 45 /8 46 /8 Flush Valve eight (FV) 6 5 /8 7 5 /8 8 5 /8 9 5 / /8 Rod eight (R) 4 5 Drain Outlet eight (D) 7 /8 8 /8 9 /8 0 /8 /8 ** assumes a typical seat thickness of " and a distance from fixture rim to mounting rod centers of ". lways refer to the manufacturer specification sheet for the latest information! These dimensions are used for later, after the frame is installed: RC: Rod Center-to-Center Distance, based on ceramic model Other calculations (for reference only) FV = FS - RT - ST + 5½" (650) R = FS - RT - ST D = FS - RT - ST - 4" (00) or FV = R + 5½" (650) = R + " (790) D = R - 4" (00) /4" FV ll dimensions bove Finished Floor () R D ST RT FS 0-4 /4" 0-4 /4" D D Compliant

4 ¼" min. 5½" wall or chase R, L or vertical drainage runs allowed with 5½" minimum wall thickness. Vertical drainage run only for ½" maximum walls. D D Compliant

5 D D Compliant 5

6 ¼" min. 5½" wall or chase R, L or vertical drainage runs allowed with 5½" minimum wall thickness. Vertical drainage run only for ½" maximum walls. D D Compliant

7 " " 6 9 " D D Compliant 7

8 4¼"-" (0-0) ½ " 9½ " min. ½" wall or chase ½"-4¼" " 44" " " R, L or vertical drainage runs allowed with 5½" minimum wall thickness. Vertical drainage run only for ½" maximum walls. D D Compliant

9 D D Compliant 9

10 ½" min wall 5½" min wall /4" /" 4 5 ½" min wall 5½" min wall /4" /" Use supplied flexible coupling (optional) Click D D Compliant

11 4 Click 9 4 ½" 5 D D Compliant

12 6 ¾ 7 5/ /8 7 /8 / 9 Ø Ø ½ 5½ ½ 8 /8 7 /8 / 9 Ø ½ Click 4 Ø Ø 5½ Contact Geberit 00 Clearwater Drive, Des Plaines, IL Phone: (847) Fax: 847/ For Technical ssistance 800 / TEC-TRUE ( ) D D Compliant

Technology. Enabling Design. Geberit Duofix Carrier

Technology. Enabling Design. Geberit Duofix Carrier Technology Enabling Design Geberit Duofix Carrier Geberit is Behind It All! With millions of installations throughout the world, the message is clear: the Geberit Duofix Carrier allows unique design without