Chem-Stud Chem-Stud 56.1 Introduction Product Description Chem-Stud Capsule Specifications. Chem-Stud Recommended Setting Time

Transcription

1 56.0 Chem-Stud 56.1 Introduction The Chem-Stud Anchor System consists of sef contained two-part gass capsues and matching chise pointed anchor rod which is instaed using a rotary hammer dri and rod adapters. The Chem-Stud adhesive is a ester based resin materia packaged in singe use gass capsues designed for use in the instaation of 3/8" through 1-1/2" threaded rod in soid concrete and masonry materias. It can aso be used for reinforcing bars. During instaation, the Chem-Stud System bonds the threaded rod to the base materia so no expansion forces are exerted against the was of the hoe in the base materia. This makes it idea for use in anchoring to soid base materias ranging from soft common brick to hard marbe or granite. Unike expansion anchors, the anchor can be set cose to the edge of the base materia Product Description CHEM-STUD Capsue Chise-Pointed Rod Internay Threaded Insert Chem-Stud Capsue The Chem-Stud adhesive is packaged in singe use gass capsues which have pre-measured components. A separate capsue is used for each size of 3/8" through 1-1/4" threaded anchor rod. An outer capsue contains epoxy acryate resin (viny ester) in which quartz aggregate is suspended. The inner capsue contains a benzo peroxide hardening agent. When the components are combined, they form an adhesive mortar which mechanicay bonds to the anchor rod to soid base materia. This type of system must be used with a chise pointed anchor rod which is spun into it using a rotary hammer dri Chem-Stud Chise Pointed Anchor Rod The Chem-Stud System is designed to be used with chise pointed anchor rods. The threaded anchor rods have a 45 chise point cut on one end to propery mix the components contained in the capsue during instaation. A 90 point is formed on the internay threaded inserts. The threaded rod or reinforcing bar used must have a chise point to mix the components contained in the capsue during instaation Chem-Stud Capsue Specifications The foowing tabe ists the shef ife and storage recommendations for the capsue. The properties isted appy to the cured Chem-Stud adhesive mortar. Shef Life 2 to 4 years Storage Conditions Store dry at 40 to 90 F. Condition to 60 F before use. Coor Mixed adhesive mortar- amber Consistency Paste mortar The mortar voume isted in the foowing tabe is for the mixed materia. The diameter and ength may be different than products offered by other manufacturer's capsues because of variations in air content. When comparing capsues, use the instaed mortar voume. Cat. Capsue Capsue Capsue Mortar Mortar No. Size Diam. Length Voume Voume /8" 0.43" 3.15" 0.35 in f. oz /2" 0.51" 3.75" 0.55 in f. oz /8" 0.67" 3.75" 0.95 in f. oz /4" 0.87" 6.63" 2.55 in f. oz /8" 0.87" 6.89" 3.25 in f. oz " 0.95" 8.25" 4.65 in f. oz /4" 1.30" 10.50" in f. oz. Chem-Stud Recommended Setting Time The setting times the for the Chem-Stud adhesive mortar are isted beow. The setting time is the minimum time required for the mortar to reach its pubished physica properties and is isted for the base materia temperature, not ambient air temperature. For exampe, when making instaations inside a buiding in exterior was during the winter, the temperature of the hoe may be different than the interior temperature and shoud be measured to determine the setting time required. In order to insure proper mixing, the capsue contents shoud be conditioned to 60 F. prior to use. Base Materia Temperature Setting Time 68 F. & over 20 minutes 50 F. to 68 F. 30 minutes 32 F. to 50 F. 1 hour 23 F. to 32 F. 5 hours 14 F. to 23 F. 10 hours 5 F. to 14 F. 18 hours 0 F. to 5 F. 24 hours Cure Time shoud be doubed for wet concrete. 190

2 56.3 Chem-Stud Adhesive Properties Resistance Of Chem-Stud Adhesive to Chemicas The resistance of the cured Chem-Stud adhesive to various chemicas was determined according to ASTM Specification C-581 by aying moded sampes of the resin in the respective chemica agents. The sampes were subjected to a bending strength test before and after a 12 month exposure to the chemicas. The adhesive was rated as resistant if there was no visibe deterioration and ess than 25% reduction in bending strength. This exposure is extreme. Under norma instaation conditions, the adhesive is exposed to the chemica agents ony at the surface of the concrete around the top of the anchor hoe. Accumuator acid Acetic acid 40 Acetic acid 10 Acetone 10 Ammonia, aqueous soution 5 Aniine 100 Beer Benzine (kp C) 100 Benzoe 100 Boric acid, aqueous soution Cacium carbonate, suspended in water A Cacium choride, suspended in water Cacium hydroxide, suspended in water Carbon tetrachoride 100 Caustic soda soution 10 Citric acid A Diese oi 100 Ethy acoho, aqueous soution 50 Formic acid 100 Formadehyde, aqueous so. 30 Freon Fue Oi Concen- Not Chemica Agent tration Resistant Resistant Gyco (Ethyene gyco) Hydrochoric acid Conc. Hydrogen peroxide 30 Isopropy acoho 100 Lactic acid A Linseed oi 100 Lubricating oi 11 Magnesium choride, aqueous soution A Methano 100 Motor oi (SAE 20 W-50) 100 Nitric acid 30 Nitric acid 10 Oeic acid 100 Perchoroethyene 100 Petroeum 100 Pheno, aqueous soution 8 Phosphoric acid 85 Potash ye (potassium hydroxide so.) 10 Potassium carbonate, aqueous soution A Potassium chorite, aqueous soution A Potassium nitrate aqueous soution A Premium gasoine 100 Sodium carbonate, aqueous soution A Sodium choride, aqueous soution A Sodium phosphate, aqueous soution A Sodium siicate A Standard Benzine 100 Sufuric acid 10 Sufuric acid 70 Tartaric acid A Tetrachoraethyene 100 Touene Concen- Not Chemica Agent tration Resistant Resistant Trichoraethyene Effect Of Eevated Temperature As with a adhesive anchors, the bond strength of the Chem-Stud is effected by eevated temperatures in the base materia. As the temperature of the base materia increases, the bond strength of the anchor wi decrease. Typica performance of the Chem-Stud Anchor at eevated base materia temperatures is shown beow. The vaues are based on maintaining the concrete test sampes used at a given temperature for a minimum of 24 hours before appying a test oad. Percent of Load Temperature ( F.) 191

3 56.4 Chem-Stud Seection Guide The foowing tabes ist the avaiabe capsue sizes aong with three types of pre-cut chise-pointed anchor rod. For specia appications, the capsues can be manufactured in other engths. The threaded rod can aso be suppied in specia engths and aternate materias. Chem-Stud Capsues Cat. *Dri Min. Std. Std. Wt./ No. Size Dia. Depth Box Ctn /8" 7/16" 3-1/2" /2" 9/16" 4-1/2" /8" 11/16" 5" /4" 7/8" 6-5/8" /8" 1" 7" " 1-1/8" 8-1/4" /4" 1-1/2" 10-1/4" * The dri bit diameters and depths isted are for instaations using threaded rod. Refer to the oad tabes for hoe size to be used with internay threaded inserts and reinforcing bars. Chem-Stud Chise-Pointed Anchor Rods Carbon stee rods are zinc pated according to ASTM B 633, SC1. A suppementa coating is appied over the zinc. For A307 anchor rod, a Type III cear chromate treatment is appied. B7 anchor rod has a Type II yeow dichromate coating. The 7/8" diameter A307 carbon stee rod is mechanicay gavanized according to ASTM B695. Additiona engths and materias are avaiabe on specia order. A307 Standard Carbon Stee, Zinc Pated (ASTM B 633) Cat. Dri Min. Std. Std. Wt./ No. Size Dia. Depth Box Ctn /8" x 5-1/8" 7/16" 3-1/2" /2" x 6-1/2" 9/16" 4-1/4" /8" x 7-1/2" 11/16" 5" /4" x 9-5/8" 7/8" 6-5/8" * 7/8" x 10-1/4" 1" 7" " x 12" 1-1/8" 8-1/4" /4" x /2" 10-1/4" * Mechanicay Gavanized B7 High-Strength Carbon, Zinc Pated (ASTM B 633) B7 (AISI 4140) anchor rod is suppied with nuts meeting the requirements of ASTM Specification A 194, Grade 2H (ASTM A 563, Grade DH) and hardened washers meeting the requirements of ASTM F 436. Cat. Dri Min. Std. Std. Wt./ No. Size Dia. Depth Box Ctn /8" x 5-1/8" 7/16" 3-1/2" /2" x 6-1/2" 9/16" 4-1/4" /8" x 7-1/2" 11/16" 5" /4" x 9-5/8" 7/8" 6-5/8" /8" x 10-1/4" 1" 7" " x 12" 1-1/8" 8-1/4" /4" x /2" 10-1/4" Stainess Stee (Passivated) Cat. Dri Min. Std. Std. Wt./ No. Size Dia. Depth Box Ctn /8" x 5-1/8" 7/16" 3-1/2" /2" x 6-1/2" 9/16" 4-1/4" /8" x 7-1/2" 11/16" 5" /4" x 9-5/8" 7/8" 6-5/8" /8" x 10-1/4" 1" 7" " x 12" 1" 8-1/4" /4" x /2" 10-1/4" Carbon Stee Internay Threaded Inserts, Zinc Pated (ASTM B 633) Cat. Dri Min. Thrd. Std. Std. Wt./ No. Size O.D. Dia. Depth Length Box Ctn /8" x 3-1/2" 0.55" 5/8" 3-1/2" 1-1/2" /2" x 4-1/4" 0.65" 11/16" 4-1/4" 1-5/8" /8" x 5" 0.90" 1" 5" 2-3/8" /4" x 6-5/8" 1.00" 1-1/8" 6-5/8" 2-3/4" Chem-Stud Instaation Toos Chem-Stud instaation toos consist of a drive adapter which is designed to fit the rotary hammer dri used and a couper to hod either threaded rods or reinforcing bars. The toos for threaded rod and reinforcing bars are different and can not be interchanged Threaded Rod Instaation Toos Coupers for Threaded Rod Cat. No. Size Std. Box Std. Ctn /8" /2" /8" /4" /8" " /4" 1 10 Drivers for Threaded Rod Coupers Cat. No. Shank Types Hex Fits Couper Std. HEX SDS A & B SPLINE SDS-Max Size Size Box /4" 3/8" to 5/8" /8" 3/4" to 1-1/4" /4" 3/8" to 5/8" /8" 3/4" to 1-1/4" 1 Reinforcing Bar Instaation Toos Chem-Stud Rebar Coupers and Drivers Cat. Std. Std. No. Size Box Ctn #3 Couper #4 Couper #5 Couper #6 Couper #7 Couper #8 Couper #9 Couper #10 Couper Ski 726 Driver Spine Driver SDS-Max Driver

4 Internay Threaded Insert Toos Coupers for Internay Threaded Inserts* Cat. Std. Std. No. Size Box Ctn /8" /2" /8" /4" 1 10 *Use with drivers for threaded rod Instaation Specifications The instaation requirements isted in the foowing tabes are based on the minimum embedment depth. Adhesive mortar voume per inch is based on the use of carbide tipped masonry bits which meet ANSI Standard B toerances. The combination of capsues to use for various embedment depths is isted in the oad capacity sections which foow. To cacuate the voume of adhesive mortar required for an embedment depth not isted, mutipy the mortar voume per inch from the foowing tabes by the embedment required. Seect a combination of capsues using the capsue mortar voume in cubic inches. When seecting a combination of capsues, use sizes cosest to the diameter of the rod to be used. For exampe, an instaation using 5/8" threaded anchor rod at an 8" embedment requires 1.47 (8 x 0.184) cubic inches of adhesive mortar. A combination of a 5/8" capsue (0.95 cu. in.) and a 1/2" capsue (0.55 cu. in.) yieds 1.50 cubic inches of adhesive mortar. Specifications For Threaded Rod Max. Mortar Rod Dri Capsue Embed. Torque Per Inch Size Dia. Size Depth (ft.-bs.) (cu. in.) 3/8" 7/16" 3/8" 3-1/2" /2" 9/16" 1/2" 4-1/4" /8" 11/16" 5/8" 5" /4" 7/8" 3/4" 6-5/8" /8" 1" 7/8" 7" " 1-1/8" 1" 8-1/4" /4" 1-1/2" 1-1/4" 10-3/4" /8" 1-5/8" 1-1/4" 10-1/4" /2" 1-3/4" 1-1/4" 10-1/4" Specifications For Reinforcing Bars *Mortar Rebar Rebar Dri Capsue Embed. Per Inch Size Size Dia. Size Depth (cu. in.) No. 3 3/8" 1/2" 3/8" 3-1/2" No. 4 1/2" 5/8" 1/2" 4-1/2" No. 5 5/8" 3/4" 5/8" 5" No. 6 11/16" 7/8" 3/4" 7" No. 7 7/8" 1" 7/8" 7" No. 8 1" 1-1/4" 1" 8-1/2" No /8" 1-3/8" 1" 9" No /4" 1-5/8" 1-1/4" 10" No /8" 1-3/4" 1-1/4" 10" * Actua adhesive mortar voume required wi be ess due to 31raised deformations on the reinforcing bars Instaation Procedures Threaded Rod or Reinforcing Bar must have a Chise Point Dri a hoe to the size and embedment required. The toerances of the dri bit used shoud meet the requirements of ANSI B Bow the hoe cean with compressed air, brush the hoe, and bow it cean again. Hoes may be dry or damp, but shoud be free of standing water or frost. Insert the capsue into the hoe. Either end of the capsue may be inserted first. Thread the nut onto the anchor rod eaving 3 to 4 threads exposed. Then thread the rod couper onto the threaded rod unti it is tight against the nut. If using reinforcing, insert the bar into the proper size couper. The threaded rod or reinforcing bar used shoud be free of dirt, grease, oi, or other foreign materia. Seect the drive unit, insert it into a rotary hammer dri and engage the couping to be used. Insert the chise point of the rod or rebar into the hoe to break the gass capsue. Spin it into the capsue at a speed of 250 to 500 RPM unti it is fuy embedded. Once the rod or bar is fuy embedded, turn the rotary hammer dri off immediatey. If instaing threaded rod, pu the driver out of the couping whie hoding the rod. Hod the hex nut with a wrench to unthread the couper. If using reinforcing bar, reease the set ever and side the couper off the bar. Aow the adhesive to cure for the specified time prior to appying any oad. Do not disturb or oad the anchor unti it is fuy cured. 193

5 56.7 Performance Data Chem-Stud Utimate Load Capacities for Instaations Using Threaded Rod in Concrete The foowing capacities are the utimate or faiure oad for the Chem-Stud adhesive when tested with high strength anchor rod in three compressive strengths of concrete. The capacity of the anchor rod shoud be taken into account in the design of any anchorage. The aowabe oad capacities for the Chem-Stud adhesive and five types of anchor rod are described in the next section. The combination of capsues shown are required to insure that the proper bond area is achieved for each of the embedments isted. Do not attempt to use more than two capsues as the dri equipment used for instaation may not have enough torque to propery spin the rod into the capsue. For instaations where the combined ength of capsues exceeds the ength of the anchor hoe, crush the first capsue using the anchor rod, then insert the second capsue. The arger capsue shoud be inserted into the anchor hoe first. Anchor Dri Embed. Number And Size 2,000 psi Concrete 4,000 psi Concrete 6,000 psi Concrete Size Dia. Depth Of Capsue (s) Tension Shear Tension Shear Tension Shear (inches) (inches) (inches) Required (bs.) (bs.) (bs.) (bs.) (bs.) (bs.) 3/8 7/16 3-1/2 One - 3/8 7,140 6,480 7,820 6,480 9,670 6,480 3/8 7/16 5-1/4 Two - 3/8 10,710 6,480 11,725 6,480 14,505 6,480 3/8 7/16 7 Two - 3/8 14,275 6,480 15,635 6,480 19,340 6,480 1/2 9/16 4-1/4 One - 1/2 9,350 11,120 13,435 11,120 14,995 11,120 1/2 9/16 6-3/8 One - 1/2 & One -3/8 14,025 11,120 20,155 11,120 22,495 11,120 1/2 9/16 8-1/2 Two - 1/2 18,700 11,120 26,870 11,120 29,990 11,120 5/8 11/16 5 One - 5/8 14,650 17,650 20,585 17,650 22,560 17,650 5/8 11/16 7-1/2 One - 5/8 & One -1/2 21,975 17,650 30,880 17,650 32,970 17,650 5/8 11/16 10 Two - 5/8 29,300 17,650 41,170 17,650 43,960 17,650 3/4 7/8 6-5/8 One - 3/4 21,750 27,385 27,400 27,385 35,640 27,385 3/4 7/8 10 One - 3/4 & One -5/8 32,830 27,385 41,100 27,385 53,795 27,385 3/4 7/8 13-1/4 Two - 3/4 43,500 27,385 54,800 27,385 71,280 27,385 7/8 1 7 One - 7/8 25,870 36,065 35,090 36,065 39,450 36,065 7/ /4 Two - 3/4 38,805 36,065 52,635 36,065 59,175 36,065 7/ Two - 7/8 51,740 36,065 70,180 36,065 78,900 36, /8 8-1/4 One ,910 53,135 47,800 53,135 55,870 53, /8 12-3/8 One - 1 & One - 7/8 53,850 53,135 71,700 53,135 83,805 53, /8 16-1/2 Two ,800 53,135 95,600 53, ,740 53, /4 1-1/2 10-1/4 One - 1-1/4 59,740 68,000 70,100 68,000 92,400 68, /4 1-1/2 15 One - 1-1/4 & One -1 87,424 68, ,585 68, ,000 68, /4 1-1/2 20-1/2 Two - 1-1/4 119,480 68, ,200 68, ,000 68, /8 1-5/8 10-1/4 One - 1-1/4 63,000 82,000 74,000 82,000 95,000 82, /8 1-5/8 15 One - 1-1/4 & One -1 92,225 82, ,085 82, ,000 82, /8 1-5/8 20-1/2 Two - 1-1/4 126,040 82, ,500 82, ,000 82, /2 1-3/4 10-1/4 One - 1-1/4 67,000 94,500 78,000 94,500 98,000 94, /2 1-3/4 15 One - 1-1/4 & One ,460 94, ,995 94, ,400 94, /2 1-3/4 20-1/2 Two - 1-1/4 134,000 94, ,000 94, ,000 94,

6 Chem-Stud Aowabe Load Capacities for Instaations Using Threaded Rod in Concrete The vaues isted in the foowing tabes are the aowabe or working oads for the adhesive and five types of stee using the foowing criteria. The tension and shear vaues isted for the aowabe bond strength of the adhesive are based on appying a safety factor of four to the average utimate oad capacities isted in the previous tabe. The aowabe stee strength vaues are based on the AISC Manua of Stee Construction (Ninth Edition). Vaues for B7 stee rod are based on A325 capacities. The aowabe oad shoud be the esser of the bond or stee strength. Aowabe Tension Aowabe Bond Strength (bs.) Aowabe Stee Strength (bs.) Anchor Dri Embed. Size Dia. Depth 2,000 psi 4,000 psi 6,000 psi A36 A307 B7 304 SS 316 SS (inches) (inches) (inches) Concrete Concrete Concrete Stee Stee Stee Stee Stee 3/8 7/16 3-1/2 1,785 1,955 2,415 2,100 2,200 4,840 2,720 2,720 3/8 7/16 5-1/4 2,675 2,930 3,625 2,100 2,200 4,840 2,720 2,720 3/8 7/16 7 3,570 3,910 4,835 2,100 2,200 4,840 2,720 2,720 1/2 9/16 4-1/4 2,340 3,360 3,750 3,745 3,920 8,625 4,850 4,850 1/2 9/16 6-3/8 3,505 5,040 5,625 3,745 3,920 8,625 4,850 4,850 1/2 9/16 8-1/2 4,675 6,720 7,500 3,745 3,920 8,625 4,850 4,850 5/8 11/16 5 3,665 5,145 5,640 5,865 6,140 13,510 7,560 7,560 5/8 11/16 7-1/2 5,495 7,720 8,245 5,865 6,140 13,510 7,560 7,560 5/8 11/ ,325 10,295 10,990 5,865 6,140 13,510 7,560 7,560 3/4 7/8 6-5/8 5,440 6,850 8,910 8,440 8,840 19,450 10,940 10,940 3/4 7/8 10 8,210 10,275 13,450 8,440 8,840 19,450 10,940 10,940 3/4 7/8 13-1/4 10,875 13,700 17,820 8,440 8,840 19,450 10,940 10,940 7/ ,470 8,775 9,865 11,480 12,020 26,455 14,875 14,875 7/ /4 9,700 13,160 14,795 11,480 12,020 26,455 14,875 14,875 7/ ,935 17,545 19,725 11,480 12,020 26,455 14,875 14, /8 8-1/4 8,980 11,950 13,970 14,995 15,700 34,450 19,430 19, /8 12-3/8 13,465 17,925 20,950 14,995 15,700 34,450 19,430 19, /8 16-1/2 17,950 23,900 27,935 14,995 15,700 34,450 19,430 19, /4 1-1/2 10-1/4 14,935 17,525 23,100 23,400 24,450 53,990 30,370 30, /4 1-1/ ,855 25,645 31,250 23,400 24,450 53,990 30,370 30, /4 1-1/2 20-1/2 29,870 35,050 37,250 23,400 24,450 53,990 30,370 30, /8 1-5/8 10-1/4 15,750 18,500 23,750 28,400 29,700 65,340 36,730 36, /8 1-5/ ,055 27,021 31,250 28,400 29,700 65,340 36,730 36, /8 1-5/8 20-1/2 31,510 35,625 37,250 28,400 29,700 65,340 36,730 36, /2 1-3/4 10-1/4 16,750 19,500 24,500 33,700 35,340 77,750 43,735 43, /2 1-3/ ,115 29,250 34,350 33,700 35,340 77,750 43,735 43, /2 1-3/4 20-1/2 33,500 36,250 37,250 33,700 35,340 77,750 43,735 43,735 Aowabe Shear Anchor Dri Embed. Aowabe Bond Strength (bs.) Aowabe Stee Strength (bs.) Size Dia. Depth 2,000 psi 4,000 psi 6,000 psi A36 A307 B7 304 SS 316 SS (inches) (inches) (inches) Concrete Concrete Concrete Stee Stee Stee Stee Stee 3/8 7/16 3-1/2 1,620 1,620 1,620 1,090 1,100 2,310 1,400 1,400 1/2 9/16 4-1/4 2,780 2,780 2,780 1,940 1,960 4,115 2,500 2,500 5/8 3/4 5 4,415 4,415 4,415 3,040 3,070 6,450 3,915 3,915 3/4 7/8 6-5/8 7,315 7,315 7,315 4,380 4,420 9,280 5,635 5,635 7/ ,015 9,015 9,015 5,950 6,010 12,620 7,665 7, /8 8-1/4 13,285 13,285 13,285 7,770 7,850 16,485 10,010 10, /4 1-1/2 10-1/4 17,000 17,000 17,000 12,150 12,270 25,770 15,645 15, /8 1-5/8 10-1/4 20,500 20,500 20,500 14,690 14,850 31,160 18,920 18, /2 1-3/4 10-1/4 23,625 23,625 23,625 17,490 17,670 37,110 22,530 22,

7 Chem-Stud Utimate Tension Load Capacities for Instaations Using Reinforcing Bars in Concrete The foowing capacities are the utimate or faiure oads for the Chem-Stud adhesive when tested with Grade 60 reinforcing bar. The stee strength vaues are based on ASTM Standard A 615. The utimate tension oads for the Chem- Stud adhesive shoud be used as a guide. Actua resuts may vary depending on the base materia condition and reinforcing bar toerances. The combination of capsues shown are required to insure that the proper bond area is achieved for each of the embedments isted. Do not attempt to use more than two capsues as the dri equipment used for instaation may not have enough torque to propery spin the rod into the capsue. For instaations where the combined ength of capsues exceeds the ength of the anchor hoe, crush the first capsue using the anchor rod, then insert the second capsue. The arger capsue shoud be inserted into the anchor hoe first. Rebar Dri Embed. Number And Size Utimate Bond Strength (bs.) Grade 60 Rebar Size Dia. Depth Of Capsue (s) 2,000 psi 4,000 psi 6,000 psi Yied UTS (inches) (inches) (inches) Required Concrete Concrete Concrete (bs.) (bs.) No. 3 (3/8) 1/2 3-1/2 One - 3/8 7,400 13,300 13,300 6,600 9,900 No. 3 (3/8) 1/2 5-1/4 Two - 3/8 11,100 19,950 19,950 6,600 9,900 No. 3 (3/8) 1/2 7 Two - 3/8 14,800 26,600 26,600 6,600 9,900 No. 4 (1/2) 5/8 4-1/2 One - 1/2 10,450 16,650 17,450 12,000 18,000 No. 4 (1/2) 5/8 6-3/4 One - 1/2 & One - 3/8 15,675 24,975 26,175 12,000 18,000 No. 4 (1/2) 5/8 9 Two - 1/2 20,900 33,300 34,900 12,000 18,000 No. 5 (5/8) 3/4 5 One - 5/8 15,460 26,200 26,200 18,600 27,900 No. 5 (5/8) 3/4 7-1/2 One - 5/8 & One - 1/2 23,190 39,300 39,300 18,600 27,900 No. 5 (5/8) 3/4 10 Two - 5/8 30,920 52,400 52,400 18,600 27,900 No. 6 (3/4) 7/8 7 One - 3/4 22,760 33,020 36,780 26,400 39,600 No. 6 (3/4) 7/8 10-1/2 One - 3/4 & One - 5/8 34,140 49,530 55,170 26,400 39,600 No. 6 (3/4) 7/8 14 Two - 3/4 45,520 66,040 73,560 26,400 39,600 No. 7 (7/8) 1 7 One - 7/8 26,500 37,000 42,330 36,000 54,000 No. 7 (7/8) /2 Two - 3/4 39,750 55,500 63,495 36,000 54,000 No. 7 (7/8) 1 14 Two - 7/8 53,000 74,000 84,660 36,000 54,000 No. 8 (1) 1-1/4 8-1/2 One ,650 53,500 56,840 47,400 71,100 No. 8 (1) 1-1/4 12-3/4 One - 1 & One - 3/4 54,975 80,250 85,260 47,400 71,100 No. 8 (1) 1-1/4 17 Two , , ,680 47,400 71,100 No. 9 (1-1/8) 1-3/8 9 One ,440 63,850 75,700 60,000 90,000 No. 9 (1-1/8) 1-3/8 13-1/2 One - 1 & One - 7/8 74,160 95, ,550 60,000 90,000 No. 9 (1-1/8) 1-3/8 18 Two , , ,400 60,000 90,000 No. 10 (1-1/4) 1-5/8 10 One - 1-1/4 57,000 72,470 92,400 76, ,300 No. 10 (1-1/4) 1-5/8 15 One - 1-1/4 & One - 7/8 85, , ,000 76, ,300 No. 10 (1-1/4) 1-5/8 20 Two - 1-1/4 114, , ,000 76, ,300 No. 11 (1-3/8) 1-3/4 10 One - 1-1/4 65,000 76,000 94,000 93, ,400 No. 11 (1-3/8) 1-3/4 15 One - 1-1/4 & One - 7/8 92, , ,000 93, ,000 No. 11 (1-3/8) 1-3/4 20 Two - 1-1/4 126, , ,000 93, ,

8 Chem-Stud Aowabe Load Capacities for Instaations Using Reinforcing Bar Instaation in Concrete The vaues isted for the aowabe bond strength in the foowing tabe are based on appying a safety factor of four to the utimate oad capacities isted in the previous tabe. The stee strength vaues in tension for reinforcing bars are based upon the aowabe stresses as isted in Section of the Uniform Buiding Code. The aowabe oad shoud be the esser of the bond strength or the stee strength. Aowabe Tension Rebar Dri Embed Aowabe Bond Strength (bs.) Rebar Strength (bs.) Size Dia. Depth 2,000 psi 4,000 psi 6,000 psi Grade 40 Grade 60 (inches) (inches) (inches) Concrete Concrete Concrete Rebar Rebar No. 3 (3/8) 1/2 3-1/2 1,850 3,325 3,325 2,200 2,640 No. 3 (3/8) 1/2 5-1/4 2,775 4,990 4,990 2,200 2,640 No. 3 (3/8) 1/2 7 3,700 6,650 6,650 2,200 2,640 No. 4 (1/2) 5/8 4-1/2 2,615 4,165 4,365 4,000 4,800 No. 4 (1/2) 5/8 6-3/4 3,920 6,245 6,545 4,000 4,800 No. 4 (1/2) 5/8 9 5,225 8,325 8,725 4,000 4,800 No. 5 (5/8) 3/4 5 3,865 6,550 6,550 6,200 7,440 No. 5 (5/8) 3/4 7-1/2 5,800 9,825 9,825 6,200 7,440 No. 5 (5/8) 3/4 10 7,730 13,100 13,100 6,200 7,440 No. 6 (3/4) 7/8 7 5,690 8,255 9,195 8,800 10,560 No. 6 (3/4) 7/8 10-1/2 8,535 12,385 13,795 8,800 10,560 No. 6 (3/4) 7/ ,380 16,510 18,390 8,800 10,560 No. 7 (7/8) 1 7 6,625 9,250 10,585 12,000 14,400 No. 7 (7/8) /2 9,940 13,875 15,875 12,000 14,400 No. 7 (7/8) ,250 18,500 21,165 12,000 14,400 No. 8 (1) 1-1/4 8-1/2 9,165 13,375 14,210 15,800 18,960 No. 8 (1) 1-1/4 12-3/4 13,745 20,065 21,315 15,800 18,960 No. 8 (1) 1-1/ ,325 26,750 28,420 15,800 18,960 No. 9 (1-1/8) 1-3/8 9 12,360 15,965 18,925 20,000 24,000 No. 9 (1-1/8) 1-3/8 13-1/2 18,540 23,945 28,390 20,000 24,000 No. 9 (1-1/8) 1-3/ ,720 31,925 37,850 20,000 24,000 No. 10 (1-1/4) 1-5/ ,250 18,120 23,100 25,400 30,480 No. 10 (1-1/4) 1-5/ ,375 27,175 31,500 25,400 30,480 No. 10 (1-1/4) 1-5/ ,500 36,235 38,000 25,400 30,480 No. 11 (1-3/8) 1-3/ ,250 19,000 23,500 31,200 37,440 No. 11 (1-3/8) 1-3/ ,000 28,500 31,000 31,200 37,440 No. 11 (1-3/8) 1-3/ ,500 37,000 38,500 31,200 37,

9 Chem-Stud Utimate Load Capacities for Instaations Using Internay Threaded Inserts in Concrete The foowing capacities are the utimate or faiure oad for the Chem-Stud adhesive when tested with high strength anchor rod in three compressive strengths of concrete. The capacity of the anchor rod shoud be taken into account in the design of any anchorage. The aowabe oad capacities for the Chem-Stud adhesive and five types of anchor rod are described in the next section. Anchor Dri Embed. Number And Size 2,000 psi Concrete 4,000 psi Concrete 6,000 psi Concrete Size Dia. Depth Of Capsue (s) Tension Shear Tension Shear Tension Shear (inches) (inches) (inches) Required (bs.) (bs.) (bs.) (bs.) (bs.) (bs.) 3/8 5/8 3-1/2 One - 3/8 7,630 6,480 8,240 6,480 9,860 6,480 1/2 11/16 4-1/4 One - 1/2 9,670 11,120 12,300 11,120 14,870 11,120 5/8 1 5 One - 5/8 15,230 17,650 21,450 17,650 23,440 17,650 3/4 1-1/8 6-5/8 One - 3/4 23,420 27,385 28,420 27,385 35,840 27, Chem-Stud Aowabe Load Capacities for Instaations Using Internay Threaded Inserts in Concrete The vaues isted in the foowing tabes are the aowabe or working oads for the adhesive and five types of stee using the foowing criteria. The tension and shear vaues isted for the aowabe bond strength of the adhesive are based on appying a safety factor of four to the average utimate oad capacities isted in the previous tabe. The aowabe stee strength vaues are based on the AISC Manua of Stee Construction (Ninth Edition). Vaues for B7 stee rod are based on A325 capacities. The aowabe oad shoud be the esser of the bond or stee strength. Aowabe Tension Anchor Dri Embed. Aowabe Bond Strength (bs.) Aowabe Stee Strength (bs.) Size Dia. Depth 2,000 psi 4,000 psi 6,000 psi A36 A307 B7 304 SS 316 SS (inches) (inches) (inches) Concrete Concrete Concrete Stee Stee Stee Stee Stee 3/8 5/8 3-1/2 1,910 2,060 2,465 2,100 2,200 4,840 2,720 2,720 1/2 11/16 4-1/4 2,420 3,075 3,720 3,745 3,920 8,625 4,850 4,850 5/ ,810 5,365 5,860 5,865 6,140 13,510 7,560 7,560 3/4 1-1/8 6-5/8 5,855 7,105 8,960 8,440 8,840 19,450 10,940 10,940 Aowabe Shear Anchor Dri Embed. Aowabe Bond Strength (bs.) Aowabe Stee Strength (bs.) Size Dia. Depth 2,000 psi 4,000 psi 6,000 psi A36 A307 B7 304 SS 316 SS (inches) (inches) (inches) Concrete Concrete Concrete Stee Stee Stee Stee Stee 3/8 5/8 3-1/2 1,620 1,620 1,620 1,090 1,100 2,310 1,400 1,400 1/2 11/16 4-1/4 2,780 2,780 2,780 1,940 1,960 4,115 2,500 2,500 5/ ,415 4,415 4,415 3,040 3,070 6,450 3,915 3,915 3/4 1-1/8 6-5/8 6,845 6,845 6,845 4,380 4,420 9,280 5,635 5,

10 56.8 Chem-Stud Specia Appications Instaation Of Anchors Under Water Chem-Stud Anchor capsues can be used to insta threaded anchor rod or reinforcing bars in submerged appications under water provided some instaation and design criteria are foowed. The anchor hoes shoud be prepared foowing the standard instructions with the foowing exceptions. Specia care shoud be taken to cean the anchor hoe as a surry of concrete paste tends to form on the was of the anchor hoe when driing under water. Insert the proper size capsue into the anchor hoe. Be sure the capsue is fuy inserted to the bottom of the hoe. Foow the standard instaation instructions for spinning the anchor rod used into the capsue with an appropriate too for submerged use. The setting time of the Chem-Stud adhesive in submerged appications depends upon the base materia temperature as shown in Section Laboratory tests and fied experience have shown that a decrease of 15 to 20% in the utimate tension oad capacity can be expected for an adhesive anchor which is instaed under water. The design professiona shoud incude this reduction in his cacuations. If the tension capacities are critica, a job site test is recommended Suggested Specification The adhesive used sha be a two part capsue type system containing an epoxy acryate resin. The outer capsue sha contain the resin in which quartz aggregate sha be suspended and the inner capsue sha contain a dibenzoy peroxide hardener. The capsue used sha have a minimum shef ife of two years. Anchor hoes sha be dried with a bit meeting the requirements of ANSI Standard B and sha be approved by the manufacturer. The adhesive capsue and anchor hardware components sha be instaed according to the manufacturers instructions. Anchor rods (or inserts) sha be manufactured from stee and sha have a chise point to propery mix the capsue. Chem- Stud capsues and the hardware used (except for reinforcing bar) sha be suppied by Powers Fastening, Inc Approvas and Listings The foowing approvas and istings are four reference purposes. They shoud be reviewed by the design professiona responsibe for the product instaation to verify approved base materias, sizes, and compiance with oca codes. ICBO ES Research Report No City Of Los Angees Research Report No Instaation Of Anchors Overhead Prior to instaing adhesive anchors overhead or in was, consut with the governing buiding authority to determine the requirements for fire safety guideines. The effect of eevated temperature on the Chem-Stud adhesive is shown in Section Chem-Stud capsues can be used for the instaation of threaded anchor rod overhead. The anchor hoes shoud be prepared foowing the standard instructions with the foowing exceptions. After the anchor hoe is dried and ceaned, insert the proper size capsue into the hoe. For the 3/8" to 1" sizes, seect the proper size anchor sea pug and insert it into the hoe unti the rim of the pug is fuy seated against the base materia. Be sure the hoe is deep enough to accept both the capsue and the pug. Foowing the standard instaation instructions, insert the chise-pointed anchor rod through the cross cut opening of the anchor sea pug and spin the rod into the capsue. An aternate method is to use a piece of duct tape or simiar materia to hod the capsue in pace prior to spinning the anchor rod into the hoe. If duct tape is used, it is necessary to hod the chise-pointed anchor rod in pace unti the adhesive ges. 199