HPS ECO ² Chamber Sections

Transcription

1 HPS ECO ² Chamber Sections

2 At HPS we develop and source innovative products from across the UK and Europe to provide cutting edge, cost effective, environmentally friendly solutions for access and drainage chamber requirements in highways and pavements. Our aim is to enable designers and contractors who build our roads or install or maintain pipework and drainage infrastructure to have fast, effective access to the most advanced and practical access and drainage solutions anywhere in the market. By combining your continuous feedback on the problems and challenges you face with our knowledge and expertise, we ensure our ever expanding portfolio of products always delivers what you are looking for. By linking different manufacturers unique products we can devise individual solutions to every issue you face. In short, you need look no further than HPS for all your roadway access and drainage chamber needs.

3 HPS have designed our ECO 2 Chamber range of products to be an environmentally friendly, robust system, compatible with existing concrete chamber sections used throughout the Water Utility market. A comprehensive range of Hydrant, Service Valve, Metering and Access and accessories, that offers significant advantages over conventional concrete sections. Environmentally friendly manufactured from multi-component recycled plastic usually destined for landfill (PVC, PP, HDPE AND LDPE) 100% recyclable Strong, robust construction gives improved whole life cost due to increased life span of product and less wastage due to breakages during transport or installation Health and safety friendly lightweight, easy to handle, no sharp or rough edges, all but one of our chamber sections conform to Manual Handling Regulations (heavy lifting equipment not required) Frost proof to 30 C Resistant to acids, alkalis, fats and oils All chamber sections are compliant with BS 5834 compatible with conventional concrete chamber sections and can be installed with or retrofitted to them as repair sections if required meet the requirements laid down by BS EN 124 class D400 regarding loading 02 03

4 Standard Chamber Sections The standard chamber sections available are detailed in the table below and cover all common access chamber sizes. Due to the strength, light weight and ease of installation of the ECO 2 chamber sections our 25mm and 75mm sections cover all requirements when stacked, making it unnecessary to provide 100mm or 150mm sections. This gives the contractor the advantage of reduced stocking or ordering requirements whilst retaining the means of fine adjustment to establish the required levels. Product code mailing list Nominal Weight Eco ² mm x 150mm x 25mm 1.1kg Eco ² mm x 150mm x 75mm 2.6kg Eco ² mm x 180mm x 25mm 2.7kg Eco ² mm x 180mm x 75mm 6.4kg Eco ² mm x 230mm x 25mm 3.2kg Eco ² mm x 230mm x 75mm 7.7kg Eco ² mm x 280mm x 25mm 4.5kg Eco ² mm x 280mm x 75mm 10.8kg Eco ² mm x 455mm x 25mm 8.9kg Eco ² mm x 455mm x 75mm 20.5kg Eco ² mm x 610mm x 25mm 9.9kg Eco ² mm x 610mm x 75mm 23kg Eco ² mm x 610mm x 25mm 12.1kg Eco ² mm x 610mm x 75mm 27.9kg Eco ² 4328 BH Eco ² 4328 BV 430mm x 280mm x 40mm base slab with 230mm offset opening 430mm x 280mm x 40mm base slab with 230mm central opening 11.8kg 11.8kg Weights can vary slightly as we are using 100% recycled material.

5 Hydrant chamber Stop tap chamber Access cover Metal surface box Valve chamber Meter chamber Access cover Access cover Chamber base sections HPS Eco 2 Base Sections for 430mm x 280mm chambers are available for valve and hydrant installations. Base sections are manufactured in two piece sections as illustrated. 430mm 580mm 580mm 580mm 580mm 75mm 40mm 25mm 04 05

6 Guidance on installation of chamber sections Adequate space should be left around the chamber section to allow backfilling with suitable materials (we recommend a minimum of 150mm). The sections should be installed upon a pre made or in situ concrete base with the ground under the base compacted to a minimum depth of 100mm. Base levels should be checked to ensure clearance for installation of valve and pipework fittings etc. It is recommended that 75mm sections are used to build up the main height of the chamber with 25mm sections used for final adjustment to meet finished levels. The chambers should be capped off in the usual manner using a concrete haunching before installing the frame and cover. HPS Eco ² Chamber Sections can also be made watertight by using a suitable sealing compound. Manhole cover Minimum 150mm gap

7 HPS your road-building and drainage partner HPS ECO² 06 07

8 Highway and Pavement Solutions Ltd Apex Works Llanbrynmair Powys SY19 7DU United Kingdom Telephone +44 (0) stillsdesign.com Disclaimer The information in this brochure is to the best of our knowledge true and accurate but all instructions, recommendations or suggestions are made without guarantee. Since the conditions of use are beyond our control, we disclaim any liability for loss or damage suffered from the use of these products.