Special Provision No. 911F04 March 1997
|
|
- Leonard Charles
- 6 years ago
- Views:
Transcription
1 COATING STEEL RAILING SYSTEM(S) - Item No. Special Provision No. 911F04 March 1997 Definitions, Elimination of Pre-Start Material Sample, Material Requirements, Operational Constraints, Time Between Surface Preparation and Prime Coat Application, Surface Preparation and Coating Application, and Measurement and Testing of Coating Materials DEFINITIONS Section of OPSS 911, November 1990, is amended by the addition of the following: Interim Surface Preparation - Any method of treating a surface in preparation for coating that does not meet the requirements for the final surface preparation standard. Final Surface Preparation - The surface preparation standard(s) (eg: SSPC-SP5, SSPC-SP6, SSPC-SP10, SSPC-SP11) specified in the contract documents. To the term "Structural Steel", the phrase "structural steel piles", is added SUBMISSION AND DESIGN REQUIREMENTS Written Notices, Drawings, Certificates and Product Data Sheets Clause of OPSS 911 is amended by the addition of the following: The product data sheets shall also indicate the minimum acceptable re-coat time period for -10 C and - 20 C Pre-Start Material Sample Subsection of OPSS 911 is deleted MATERIAL Coating Systems - Except Hot Dip Galvanizing and Metallizing Subsection of OPSS 911 is deleted and replaced by the following: All coating systems shall conform to OPSS 1704, November 1990, amended as follows: REFERENCES Section of OPSS 1704 is amended by the addition of the following under "American Society for Testing and Materials": ASTM D Standard Practice for Determining Volatile Organic Compound Content of Paint and Related Coatings March 1997 Pg. 1 of 5 SSP911F04
2 General Subsection of OPSS 1704 is amended by the addition of the following: c) To qualify as a low volatile organic compound (VOC) coating, a product shall contain not more than 350 grams per litre of VOC's as defined in ASTM D Table 1 in OPSS 1704 is amended by the addition of the following: VOC Content CGSB 1-GP-71 Method ASTM SSPC Tolerances n.a. D n.a. ï10% but total not to exceed 350 g/l Material shall be delivered to the job site or the fabrication shop in the manufacturer's sealed containers bearing the manufacturer's labels conforming to OPSS Colour Subsection of OPSS 1704 is amended by deleting the second paragraph and replacing it with the following: Successive coats shall be formulated to show distinct colour difference. With the exception of coal tar epoxies, the colour of the finish coat shall be brown (1-GP-12C) for ACR steel and grey (1-GP-12C) for all other steel. Table 1 of OPSS 1704 is amended by the deletion of the tolerances for gloss: CGSB 1-GP-71 Method Physical Tests Gloss CONSTRUCTION Surface Preparation Clause of OPSS 911 is amended by the addition of the following: Steel handrails shall be cleaned to the requirements of SSPC-SP8-82 (Pickling). Steel posts, caps, and panel anchorages shall be cleaned to the requirements of SSPC-SP5-89 (White Metal Blast Cleaning) *1. Steel panel anchorages, on concrete posts, shall be cleaned to the requirements of SSPC-SP10-89 (Near- White Blast Cleaning) *2. March 1997 Pg. 2 of 5 SSP911F04
3 Operational Constraints Clause of OPSS 911 is amended by deleting the first paragraph and replacing it with the following: The final surface preparation operations shall not be carried out in the following conditions as detailed in SSPC-PA1: - Clause 6.1, "Temperature" - Clause 6.2, "Moisture" The limitations do not apply to interim surface preparation Application of Coating Clauses and of OPSS 911 are amended by the addition of the following: The area of structural steel in the handrail panels to be cleaned and hot dip galvanized is estimated to be: *3. The area of structural steel in the posts, caps, and panel anchorages to be cleaned, metallized and seal coated is estimated to be: *1 and *3. The area of structural steel in the steel panel anchorages, on concrete posts, to be cleaned and coated with the epoxy-zinc/epoxy/polyurethane system is estimated to be: *2 and *3. The coatings previously applied to the steel railing system are: *4. Clause of OPSS 911 is amended by deleting the fourth paragraph and replacing it with the following: Except for the bolts, nuts and washers in clause , all rivets, bolts, nuts and washers shall be prime coated and finish coated by brush. When the inorganic zinc primer is specified, brushing shall be carried out with the epoxy-zinc primer from the low volatile organic compound system after the spray application. The finish coat shall be brush applied prior to spray application. The finish coat shall be brush applied prior to spray application. Clauses to of OPSS 911 are deleted. Clause , "General", is amended by the addition of the following Low Volatile Organic Compound (VOC) Coating Systems: Epoxy-Zinc/Epoxy/Polyurethane System The epoxy-zinc/epoxy/polyurethane system consists of three coats and shall conform to Table A. March 1997 Pg. 3 of 5 SSP911F04
4 TABLE A Amercoat Canada Corrosion Service Co. Ltd. Coat Dry Film Thickness Dry Film Thickness Prime 75 µm minimum 75 µm minimum Second 100 µm minimum 75 µm minimum Third 50 µm minimum 75 µm minimum Seal Coating of Metallized Surfaces Clause of OPSS 911 is deleted and replaced with the following: All metallized surfaces shall be coated with epoxy mid-coat from one of the low volatile organic compound (VOC) systems. The minimum dry film thickness shall be 50 µm. The colour of the seal coat shall be a semi-gloss equivalent of grey (1-GP-12C) Touch-Up Clause of OPSS 911 is deleted and replaced with the following: Damaged areas of coated surfaces shall be cleaned of all rust and other contaminants and recoated with the same materials except for inorganic zinc primers which shall be recoated with an epoxy zinc primer from the low VOC systems. The minimum dry film thickness shall be 75 µm. The damaged areas of hot dip galvanized and metallized surfaces shall be cleaned of all rust and other contaminants and shall be recoated with two coats of zinc-rich coating. Each coat shall be 75 µm minimum dry film thickness. Where metallized surfaces have been seal coated, the seal coat shall be applied over the zinc-rich coating to a minimum dry film thickness of 50 µm. The zinc-rich coating used to touch-up the metallic coatings shall be from the zinc-rich touch-up systems Time Between Surface Preparation and Prime Coat Application Clause of OPSS 911 is deleted and replaced with the following: Except for metallizing and hot dip galvanizing, the maximum time between final surface preparation and prime coat application shall be 10 hours QUALITY ASSURANCE Inspection Subsection of OPSS 911 is deleted and replaced by the following: Each phase of work will require inspection by the Contract Administrator before proceeding to the next phase. Acceptance of the surface preparation will be based on the applicable SSPC surface preparation specifications and pictorial standards given in SSPC-Vis1 and SSPC-Vis3. March 1997 Pg. 4 of 5 SSP911F04
5 Measurement of Surface Profile Subsection of OPSS 911 is deleted and replaced by the following: Surface profile measurements will be made on a random basis by use of a spring micrometer and extra coarse, pressure sensitive replica tape Measurement of Coating Thickness Subsection of OPSS 911 is amended by the addition of the following: The Contractor shall submit two copies to the Contract Administrator of the Galvanizer's dry film readings prior to the component's installation on the structure Testing of Coating Materials Subsection of OPSS 911 is deleted and replaced by the following: Each batch of coating material shall be field sampled at the request and in the presence of the Contract Administrator. Sample containers will be supplied by the Contract Administrator. March 1997 Pg. 5 of 5 SSP911F04
Special Provision No. 911S07 October Coating the Ends of New Steel Girders with the Epoxy-Zinc/Epoxy/Polyurethane System
COATING NEW STRUCTURAL STEEL - Item No. Special Provision No. 911S07 October 2000 Coating the Ends of New Steel Girders with the Epoxy-Zinc/Epoxy/Polyurethane System 911.02 REFERENCES Section 911.02 of
More informationSpecial Provision No. 911F06 October 2000
COATING EXISTING STRUCTURAL STEEL - Item No. Special Provision No. 911F06 October 2000 References, Definitions, Pre-Tender Trials, Elimination of Pre-Start Material Sample, Material Requirements, Operational
More informationCOATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006
COATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006 Amendment to OPSS 911, November 2004 for hot dip galvanizing and subsequent painting, where required,
More informationSection 716. SHOP CLEANING AND COATING STRUCTURAL STEEL
716.01 Section 716. SHOP CLEANING AND COATING STRUCTURAL STEEL 716.01. Description. This work consists of shop cleaning and applying a complete coating system on new structural steel as a part of fabricating
More informationCONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 911 APRIL 2010 CONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS TABLE OF CONTENTS 911.01 SCOPE 911.02 REFERENCES 911.03 DEFINITIONS
More informationCONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 911 NOVEMBER 2004 CONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS TABLE OF CONTENTS 911.01 SCOPE 911.02 REFERENCES 911.03 DEFINITIONS
More informationCONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 911 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR COATING STRUCTURAL STEEL SYSTEMS TABLE OF CONTENTS 911.01 SCOPE 911.02 REFERENCES 911.03 DEFINITIONS
More informationSECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
More informationSECTION 2 DIVISION 05 METALS
SECTION 2 DIVISION 05 METALS DIVISION 5 - METALS Note: This is a guide for Designers only. Contents shall not be used in lieu of specifications as part of the Designer s Contract Documents. GENERAL DESIGN:
More information.2 Section Waste Management and Disposal.
Issued 2006/08/01 Section 05121 Structural Steel for Buildings Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal..3 Section
More informationCorrosion Protection Specifications Liquid Paint System Performance Level 113 [FC-L113 ]
Manufacturing Specification NS 113 (Effective 01Feb11) Corrosion Protection Specifications Liquid Paint System Performance Level 113 [FC-L113 ] This specification is to serve as a guide of responsibilities
More informationTested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description
Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It
More informationMETAL FABRICATION..1 General Conditions and Division 1 shall govern Work of this section.
CITY OF BRAMPTON LANDSCAPE SPECIFICATIONS SECTION 05500-1 PART 1 GENERAL 1.1 Description of Work.1 General Conditions and Division 1 shall govern Work of this section. 1.2 Quality Assurance.1 Personnel:.1
More informationMATERIAL SPECIFICATION FOR PAINT COATING SYSTEMS FOR STRUCTURAL STEEL
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 1704 NOVEMBER 2014 MATERIAL SPECIFICATION FOR PAINT COATING SYSTEMS FOR STRUCTURAL STEEL TABLE OF CONTENTS 1704.01 SCOPE 1704.02 REFERENCES 1704.03
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 402;2522 1,2 2522 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high zinc dust containing product. It conforms to
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1
7461;7680 1 7680 zinc silicate VValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It conforms
More informationSECTION STRUCTURAL STEEL
SECTION 051200 STRUCTURAL STEEL PART 1 GENERAL 1.01 SECTION INCLUDES A. Structural steel framing members and support members. B. Base plates, shear stud connectors. C. Grouting under base plates. 1.02
More informationSpecial Provision No. 599F01 May 2004 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF NOISE BARRIER TABLE OF CONTENTS
... m NOISE BARRIER - Item No.... m NOISE BARRIER INCLUDING PRECAST NOISE/TRAFFIC BARRIER - Item No.... m NOISE BARRIER ON STRUCTURES - Item No.... m SALVAGEABLE NOISE BARRIER - Item No.... m SALVAGEABLE
More informationSECTION 15 STRUCTURAL STEEL
SECTION 15 STRUCTURAL STEEL 1 GENERAL 1.1 SCOPE Outline description This section applies to the provision, fabrication, treatment, erection and connection of structural steelwork. 1.2 CROSS REFERENCES
More information.4 Submit proof of qualifications and authorization in writing to the Contract Administrator, four (4) weeks prior to commencement of Work.
Construction of Roads and Landscaping Page 1 of 8 1. GENERAL 1.1 Work Included.1 Supply and Installation of specialty coatings for the concrete pavement areas adjacent to the south side of the Bulk Chemical
More information1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCONSTRUCTION SPECIFICATION FOR METAL TRAFFIC BARRIERS AND METAL RAILINGS FOR STRUCTURES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 908 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR METAL TRAFFIC BARRIERS AND METAL RAILINGS FOR STRUCTURES TABLE OF CONTENTS 908.01 SCOPE 908.02
More informationDIVISION 5 METALS SECTION STRUCTURAL STEEL
DIVISION 5 METALS SECTION 05 12 00 PART 1 GENERAL 1.01 SUMMARY A. Section Includes: All labor and materials required to furnish and install the structural steel shown on the Drawings and required by these
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationB. Shop Drawings: Include plans, elevations, sections, details, and attachments.
SECTION 055119 - METAL GRATING STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationPRODUCT GUIDE: ZINC-RICH COATINGS. Version:
PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,
More informationMETALS Commissioning of Metals Structural Steel Framing Steel Studs... 2
~ 05-1 ~ 05 00 00 Metals 05 00 00 METALS... 2 05 08 00 Commissioning of Metals... 2 05 12 00 Structural Steel Framing... 2 05 12 30 Steel Studs... 2 05 45 00 METAL SUPPORT ASSEMBLIES... 2 05 50 00 METAL
More informationSTRUCTURAL STEEL FRAMING
SECTION 05 12 00 - STRUCTURAL STEEL FRAMING PART 1 - GENERAL 1.1 SUMMARY A. Section includes 1. Structural steel framing 2. Structural steel framing required for support and framing of rooftop mechanical
More informationSECTION METAL FLOOR PLATE STAIRS
SECTION 05513 - METAL FLOOR PLATE STAIRS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationB. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work.
SECTION 055116 - METAL FLOOR PLATE STAIRS PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II
SECTION 052100 - STEEL JOISTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections
More informationSECTION STRUCTURAL STEEL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 05 12 00 SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // ---// if not applicable to project. Also delete any other item or paragraph
More informationProperty Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 2124;7720 1,2 7720 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc epoxy coating. It provides corrosion protection as part of a complete coating
More informationCOMMERCIAL ITEM DESCRIPTION ELECTROCOATING PRIMER
[INCH-POUND] March 1, 2010 SUPERSEDING A-A-52474A December 4, 1996 COMMERCIAL ITEM DESCRIPTION ELECTROCOATING PRIMER The General Services Administration has authorized the use of this commercial item description
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 3, System 7, suitable for splash zone. Property Test/Standard Description
Other Technical Data Sheet 574;576 1,2 574 epoxy VValidationDate). 1 Product description This is a two component polyamine cured epoxy coating. It is a high solids, high build, glass flake reinforced product.
More informationCONSTRUCTION SPECIFICATION FOR EXPANDED METAL ANTI-GLARE SCREEN
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 791 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR EXPANDED METAL ANTI-GLARE SCREEN TABLE OF CONTENTS 791.01 SCOPE 791.02 REFERENCES 791.03 DEFINITIONS
More informationCONSTRUCTION SPECIFICATION FOR METAL TRAFFIC BARRIERS AND METAL RAILINGS FOR STRUCTURES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 908 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR METAL TRAFFIC BARRIERS AND METAL RAILINGS FOR STRUCTURES TABLE OF CONTENTS 908.01 SCOPE 908.02
More informationNational Master Specification (NMS) Section Publisher: Spex.ca Page 1. Approved: RELATED REQUIREMENTS.1 [ ].
National Master Specification (NMS) Section 05 50 00 METAL FABRICATIONS Publisher: Spex.ca Page 1 Approved: 2010-06-30 Part 1 General 1.1 RELATED REQUIREMENTS.1 [ ]. 1.2 REFERENCES.1 CSA International.1
More informationTested in accordance with ISO , high expected durability in corrosivity category C5-I. Property Test/Standard Description
Approved 7461;7680 1,2 7680 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a high solids, high zinc dust containing product. It
More informationSECTION METAL STAIRS
SECTION 05510 METAL STAIRS PART 1 GENERAL 1.01 SECTION INCLUDES A. Stairs with concrete treads. B. Stairs with metal treads. C. Structural steel stair framing and supports. D. Handrails and guards. 1.02
More informationSTRUCTURAL STEEL FRAMING Section
PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Structural steel. 2. Grout. 1.2 DEFINITIONS A. Structural Steel: Elements of the structural frame indicated on Drawings and as described in AISC 303,
More informationSpecial Provision No. 799F01 March 2012 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF NOISE BARRIER TABLE OF CONTENTS
... m NOISE BARRIER - Item No.... m NOISE BARRIER INCLUDING PRECAST NOISE/TRAFFIC BARRIER - Item No.... m NOISE BARRIER ON STRUCTURES - Item No.... m SALVAGEABLE NOISE BARRIER - Item No.... m SALVAGEABLE
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 16561;16840;18880 1,2 18880 epoxy mastic ^(ValidationDate) 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, abrasion resistance, high
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART 1 - GENERAL 1.01 SECTION INCLUDES A. Concrete Steps B. Handrails C. Safety Rail 1.02 DESCRIPTION OF WORK A. Construction of concrete steps. B. Furnishing
More informationProduct Guide Specification DIVISION SPECIALTIES MANUFACTURERS OF PROTECTIVE COVERS
Product Guide Specification DIVISION 107300 SPECIALTIES MANUFACTURERS OF PROTECTIVE COVERS PART 1 - GENERAL [reference CSI 2004 MasterFormat Division 10 (Specialties Manufacturers) category 7300 (Protective
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 32 C VOC-USA / VOC Hong Kong EPA Method 24
Other Technical Data Sheet 2920;2401 1 2920 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids,
More informationProperty Test/Standard Description. 53± 2 % matt (0-35) Flash point ISO 3679 Method 1 25 C calculated IED (2010/75/EU) (theoretical)
Approved 7081;7243 1,2 7243 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a fast drying, high zinc containing product. It conforms
More informationProperty Test/Standard Description. US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 2401;3440 1,2 3440 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high
More informationSpecial Provision No. 915S03 December References, Materials, Construction, and Quality Assurance for Sign Support Structures
STEEL MONOTUBE OVERHEAD SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN NON-BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. CANTILEVER STATIC SIGN
More informationMATERIAL SPECIFICATION FOR SECTIONAL STEEL HIGH MAST LIGHTING POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 2471 November 2016 MATERIAL SPECIFICATION FOR SECTIONAL STEEL HIGH MAST LIGHTING POLES TABLE OF CONTENTS 2471.01 SCOPE 2471.02 REFERENCES 2471.03
More informationProperty Test/Standard Description
Other Technical Data Sheet 24100;24120;26200 1 24100 VValidationDate). 1 Product description This is a two component, anticorrosive water borne epoxy coating. It is a versatile, fast drying product containing
More informationSECTION STEEL JOIST FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 05 21 00 1. Use this section only for NCA projects. 2. Delete between //---// if not applicable to project. Also delete any other item or paragraph not applicable
More informationPre-qualification testing in accordance with NORSOK M-501, Rev. 5, System 1, suitable for exterior exposure in offshore environment, below 120 C.
Approved 402;2521 1,2 2521 zinc epoxy ^(ValidationDate) 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationInsulating Cellular Concrete Steel Joists Painting. A. America Society for Testing and Materials (ASTM):
SECTION 05120 STRUCTURAL STEEL PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03342 - Insulating Cellular Concrete. 2. 05210 - Steel Joists. 3. 09900 - Painting. 1.02 REFERENCES A. America Society
More informationTS 24 SOUTH AUSTRALIAN WATER CORPORATION
TS 24 SOUTH AUSTRALIAN WATER CORPORATION TECHNICAL STANDARD SURFACE PREPARATION AND PROTECTION OF STEELWORK USING ZINC / EPOXY HIGH BUILD, 2-PACK MICACEOUS IRON OXIDE / GLOSS, 2-PACK TOPCOAT Issued by:
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 30 C calculated VOC-USA / VOC Hong Kong EPA Method 24
Other Technical Data Sheet 27800;27801 1 27800 VValidationDate). 1 Product description This is a two component amine cured pure epoxy coating. It is a fast drying, high solids, high build product. It provides
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 28 C
Other Technical Data Sheet 1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 200 C and can
More informationProperty Test/Standard Description
Approved 29560;29561 1 29560 zinc silicate ^(ValidationDate) 1 Product description This is a two component ceramically reinforced polyamide cured zinc rich epoxy coating. 1:1 mixing ratio for easy use
More informationDIVISION 5 METALS Metal Fabrication
DIVISION 5 METALS 05500 Metal Fabrication SECTION 05500 PART 1 GENERAL 1.1 INTENT OF SECTION.1 This section specifies requirements for the supply and installation of all miscellaneous metal fabrications,
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (28 C) VOC-USA / VOC Hong Kong EPA Method 24
1505;1506 1 1505 novolac epoxy VValidationDate). 1 Product description This is a two component polyamine cured novolac epoxy coating. It is heat resistant up to 392 F (200 C) and can be applied on hot
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 1850 APRIL 2018 (Formerly OPSS 1850, April 2013) Note: The PROV published in April 2018 replaces OPSS 1850 COMMON, April 2013 with no technical content
More informationSECTION FABRICATED ENGINEERED STRUCTURES. A. Pre-engineered, shop-fabricated structural steel building with formed purlin framing.
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 13 34 00 FABRICATED ENGINEERED STRUCTURES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationSECTION 1045 PAINT FOR STRUCTURAL STEEL
SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Paint and Paint Material. 1045.1.1 General. All single component paints shall be ready-mixed at the factory to comply with the specification formula for the
More informationSECTION METAL PLATE CONNECTED WOOD TRUSSES PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 06192 - PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationRust-Oleum Industrial Brands Specification
Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 44 A solvent based coating system High Performance 7400 System 450 VOC DTM Alkyd Enamel
More information1. Base plates, setting plates and anchor rods for columns. 8. Lintels if connected to structural steel columns.
PAGE 051200-1 SECTION 051200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationProperty Test/Standard Description. calculated US EPA method 24 (tested) (CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)
Approved 23680;1551 1,2 23680 epoxy mastic ^(ValidationDate) 1 Product description This is a two component amine cured epoxy mastic coating. It is a surface tolerant, high solids product. It is aluminum
More informationElastocoat Protective Coatings APPLICATION GUIDE
Elastocoat Protective Coatings DESCRIPTION Elastocoat polyurea and polyurethane coatings are two-component, 100% solids elastomer systems. The coatings systems are designed for processing through plural
More informationSECTION STRUCTURE MOUNT RAILING SYSTEM
SECTION 05520 STRUCTURE MOUNT RAILING SYSTEM Peak Fall Protection specializes in the design, engineering, fabrication, installation, and certification of fall protection safety systems. Our team of safety
More information7. New railings for existing buildings shall be designed to match any existing railings unless there is a compelling reason for change.
Division 05. Metals 05 50 00. Metal Fabrications 05 50 00. Roof - Fall Protection The contractor shall provide a horizontal cable lifeline system on steel posts complying with applicable regulatory requirements.
More informationTable of Contents. List of Drawings
SCOPE OF WORK Hastings Stadium Exhibition Park, 81 London Road, Guelph, Ontario Structural and Maintenance Remedial Work Prepared For City of Guelph City Hall, 1 Carden Street, Guelph, ON N1H 3A1 Prepared
More informationSECTION STRUCTURAL STEEL
SECTION 05 12 00 STRUCTURAL STEEL PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Divisions 1 Specification
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong
Approved 20920;16620 1 20920 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product.
More information1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method F (29 C) calculated VOC-US/Hong Kong
Approved 20940;16620 1 20940 epoxy ^(ValidationDate) 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high
More informationProperty Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1
2401;3440 1 3440 epoxy VValidationDate). 1 Product description This is a two component amine cured epoxy coating. It is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product.
More informationProperty Test/Standard Description STANDARD GRADE
Other Technical Data Sheet 525;527;1549 1,2 525 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids,
More informationPreassembled steel stairs with concrete-filled treads.
SECTION 055113 - PART 1 - GENERAL 1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this
More informationCONSTRUCTION SPECIFICATION FOR GUIDE RAIL END TREATMENT - EXTRUDER TERMINAL SYSTEM
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 559 NOVEMBER 2006 CONSTRUCTION SPECIFICATION FOR GUIDE RAIL END TREATMENT - EXTRUDER TERMINAL SYSTEM TABLE OF CONTENTS 559.01 SCOPE 559.02 REFERENCES
More informationNAVSEA REVIEWED ASTM F-718. Interline 783 Finish, Ultra High Solids Two-Pack Fast Cure Solvent-Free Coating
ASTM F-71 International Paint, LLC Interline 73 Finish, Ultra High Solids Two-Pack Fast Cure Solvent-Free Coating PRODUCT DESIGNATIONS Part A: THA72/THA73/THA7/THA79/THA Series Part B: THA75 MIL-PRF-23236
More informationKeuka Studios May 2008 SECTION {05720} CABLE RAILING SYSTEM {CABLE RAILING SYSTEM} Display hidden text for Specifier Notes.
SECTION 05 73 16 {05720} CABLE RAILING SYSTEM {CABLE RAILING SYSTEM} Display hidden text for Specifier Notes. PART 1 GENERAL 1.1 SUMMARY A. Section includes cable railing system, with architectural metal
More informationExterior pipes, Fences, screens, grills and gates, Metallic Structures, Structural elements (column, trusses, etc.)
DESCRIPTION ZINC-TECH GALVANIC is a single component zinc-rich anticorrosive, made from synthetic resins and pigments that allow it to provide an excellent cathodic protection against corrosion. Has galvanizing
More informationTnemec 394 Proprietary Long Form Coatings Schedule
1.1 PRIMER Tnemec 394 Proprietary Long Form Coatings Schedule A. Primer: Tnemec Series 394 PerimePrime Aromatic Polyurethane Mio/Zinc filled Primer applied @ 2.5-3.5 mils DFT and conforming to the following
More informationSIGMAZINC 160. Revision of March 2007 DESCRIPTION. two component moisture curing inorganic zinc (ethyl) silicate primer PRINCIPAL CHARACTERISTICS
5 pages Revision of March 2007 DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading
More informationAMBICO Limited Section and BLAST RESISTANT STEEL WINDOW FRAME ASSEMBLIES Page 1
Page 1 This section includes AMBICO Blast Resistant Steel Window Frame assemblies and relies on applicable industry standards. This section includes proprietary and descriptive type specification requirements.
More informationGeneral: Primarily designed for maintenance and repair. Only aluminium containing versions to be used in immersed environments.
Other Technical Data Sheet 5580;5660;6520;10760 1,2 5580 epoxy mastic VValidationDate). 1 Product description This is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high
More information1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats.
PAINTING GENERAL INFORMATION 1.1 This Section includes surface preparation and the application of base coats, intermediate and topcoats. DESIGN REQUIREMENTS 2.1 Material Compatibility: a. Provide materials
More informationSection FLUSHING HYDRANTS
STANDARD SPECIFICATION Section 02520 PART 1 GENERAL 1.01 SUMMARY This Section includes: A. Flushing hydrants. B. Adjustment of flushing hydrants and gate valves. 1.02 MEASUREMENT AND PAYMENT A. Unit Prices.
More informationDURASHIELD JARS APPLICATION SPECIFICATION SHEET FIELD-APPLIED JOINT & REPAIR SYSTEM (JARS) EFFECTIVE: 6/2/15
DURASHIELD 310-61 JARS FIELD-APPLIED JOINT & REPAIR SYSTEM (JARS) I. Scope A. This specification defines application requirements of DuraShield 310-61 Joint and Repair System (JARS) plural-component 100%
More informationSIGMACAP MASTIC GF. September surface tolerant coating for lower grade of steel preparation
5 pages DESCRIPTION PRINCIPAL CHARACTERISTICS COLOURS AND GLOSS BASIC DATA AT 20 C Mass density Volume solids VOC (supplied) Recommended dry film thickness Theoretical spreading rate Touch dry after Overcoating
More informationIn accordance with documents prepared by: The Worcester Housing Authority.
Addendum No. 3 DATE: August 29, 2018 Project: WHA Job No. 2017-07 - Building Improvements MA 12-1 Great Brook Valley Gardens In accordance with documents prepared by: The Worcester Housing Authority. TO:
More informationUFGS (July 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCESA / NASA UFGS-09 97 13.00 40 (July 2007) ------------------------------- Preparing Activity: NASA Superseding UFGS-09 97 13.00 40 (July 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More information1.4 kg/l (11.4 lb/us gal) Maximum 295 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) 50 to 63 μm (2.0 to 2.
DESCRIPTION One-component, heat-resistant silicone acrylic topcoat primarily for the PPG HI-TEMP 1027 primer or the PPG HI-TEMP 222 G primer. PRINCIPAL CHARACTERISTICS Heat-resistant silicone acrylic topcoat
More informationTS 82 TECHNICAL STANDARD SURFACE PREPARATION AND PROTECTION OF STEELWORK USING INORGANIC ZINC SILICATE AND ACRYLIC LATEX COATING SYSTEM
TS 82 SOUTH AUSTRALIAN WATER CORPORATION TECHNICAL STANDARD SURFACE PREPARATION AND PROTECTION OF STEELWORK USING INORGANIC ZINC SILICATE AND ACRYLIC LATEX COATING SYSTEM Issued by: Manager Engineering
More informationProperty Test/Standard Description
Approved 32222;32223;35142 1 32222 epoxy composite ^(ValidationDate) 1 Product description This is a two component glass flake reinforced epoxy composite coating. It is heat resistant up to 250 C (482
More information05030 METAL FINISHES/09800 SPECIAL COATINGS ZRC COLD GALVANIZING COMPOUND
05030 METAL FINISHES/09800 SPECIAL COATINGS ZRC COLD GALVANIZING COMPOUND By ZRC Worldwide 145 Enterprise Drive, Marshfield, MA 02050 Tel: 781-319-0400; Fax: 781-319-0404; E-mail: info@zrcworldwide.com
More informationSECTION METAL STAIRS
SECTION 05 51 00 METAL STAIRS PART 1 GENERAL 1.1 SUMMARY A. Section includes steel stair frame of structural sections, with closed risers; pan to receive concrete fill stair treads and landings; integral
More informationProperty Test/Standard Description Solids by volume. ISO 3233 Gloss level (60 ) ISO 2813
Other Technical Data Sheet 2063;2064 1,2 2063 epoxy VValidationDate). 1 Product description This is a two component solvent free polyamine cured epoxy coating. It is a general purpose tank lining with
More information