General Symbols, Ducts and Cables
|
|
|
- Ethan Gregory
- 6 years ago
- Views:
Transcription
1 DIVISION ABBREVIATIONS Abbreviations, General General Symbols, Ducts and Cables General Symbols, Maintenance Holes, Junction Boxes, Pads, and Footings General Symbols, Poles and Guying General Symbols, Power Supply Equipment General Symbols, Control Equipment General Symbols, Traffic Actuation Devices Highway Lighting Symbols, Luminaires Electrical Traffic Control Symbols, Traffic Control Devices Electrical Traffic Control Symbols, Traffic Signal Displays Wiring Symbols, Wiring Diagrams Wiring Symbols, Wiring Diagrams Advanced Traffic Management Symbols, Universal Traffic Management System, Equipment Identifier Advanced Traffic Management Symbols, Universal Traffic Management System, Equipment Identifier Advanced Traffic Management Symbols, Layout Drawings Advanced Traffic Management Symbols, Wiring Diagrams Communications Symbols, Fibre Optic Communications Schematic Communications Symbols, Fibre Optic Communications Schematic 2 DIVISION UNDERGROUND WORK, ETC Cable Installation in Trenches Cable and Duct Protection and Marking Rigid Ducts Encased in Concrete November 2014 Page 1
2 Duct Installation in Trenches Extension of Existing Rigid Ducts Encased in Concrete Underground Rigid Duct Connection at Concrete Structure Rigid Duct Termination for High Voltage Cables at Utility Poles Duct Installation Profiles Duct Installation in Existing Paved Area, Unshrinkable Backfill Method Rigid Duct Installation in Existing Paved Area - Granular Backfill Method Duct Installation at Utility Crossings Augering Pits for Subsurface Installation of Ducts and Encasements Re Ducts Surface Mounted on Structures Electrical Maintenance Hole - Cast-in-Place mm x 1200 mm Electrical Maintenance Hole - Cast-in-Place mm x 1450 mm Electrical Maintenance Hole - Cast-in-Place mm x 2440 mm Electrical Maintenance Hole - Cast-in-Place mm x 1650 mm Electrical Maintenance Hole - Precast Concrete mm x 1450 mm Electrical Maintenance Hole - Precast Concrete mm Dia Electrical Maintenance Hole - Precast Concrete mm x 1650 mm Electrical Maintenance Hole - Precast Concrete mm x 2400 mm Electrical Handhole, Precast Concrete with Cover, 300 mm Dia Electrical Handhole, Precast Concrete with Cover, 460 mm Dia Electrical Handhole Precast Concrete mm Dia. November 2014 Page 2
3 Electrical Handhole Precast Concrete x 600 mm Electrical Handhole, Precast Concrete with Cover, 300 x 500 mm Electrical Handhole, Non and Semi-Concrete, General Requirements Drainage Facilities for Electrical Maintenance Holes Electrical Maintenance Hole, Drains to Drainage Pockets, Embankment Outlets, and Ditches Electrical Maintenance Hole, Drains to Storm Sewer Systems Electrical Maintenance Holes, General Installation Requirements Electrical Handholes, General Installation Requirements Electrical Chamber Installation in Median Electrical Chamber Installation in Slope Electrical Maintenance Holes, Entry of Direct Buried Ducts Electrical Maintenance Holes, Entry of Encased Ducts Electrical Handholes, Entry of Direct Buried and Encased Ducts Distribution Assembly, Concrete Pad and Ducts, Plan and Section A-A Distribution Assembly, Concrete Pad and Ducts, Section B-B Supply Control Cabinet Installation Overhead Services, Top Entry Metering Supply Control Cabinet Installation, Underground Services, Bottom Entry Metering Supply Control Cabinet Installation, Overhead Services, Bottom Entry Metering DIVISION FOUNDATIONS, ETC Concrete Footing for Base Mounted Lighting and Signal Poles Raised Concrete Footing for Base Mounted Lighting Poles Concrete Foundation for Direct Buried Lighting Poles Where Rock is Encountered November 2014 Page 3
4 Concrete Foundation for Base Mounted Lighting Poles Where Rock is Encountered Concrete Footing and Anchorage Assembly for 3.3 m Base Mounted Metal Pole Concrete Footing for 1.5 m Base Mounted Pedestrian Push Button Pole Pole Footing in Earth for Cast-In-Place Concrete Barrier Pole Footing in Rock for Cast-In-Place Concrete Barrier Local Grading at Pole Foundations Installation of Direct Buried Poles in Slopes High Mast Lighting Pole, Apron Anchorage Assembly Pole Mounting Details for Base Mounted Metal Pole Anchorage Assembly for Pole Footing in Concrete Barrier High Mast Lighting Pole Anchorage Assembly Placement Pole Handhole Locations Concrete Lighting Pole, Direct Buried Metal Lighting Pole, Base Mounted Sectional Steel Pole with Brackets, Luminaire, and Traffic Signal Head Pole Guying Details Wooden Pole and Anchorage Settings in Solid Rock Wooden Pole and Anchorage Settings in Solid Rock Wooden Pole in Earth Cribbing for Wood Poles in Muskeg Log Anchor for Guy in Muskeg Wood Pole with Elliptical Bracket, Overhead and Underground Circuits Wooden Pole with Neutral Supported Cable November 2014 Page 4
5 Wooden Poles with Aerial Signal Cables Lashed on Messenger Installation of Aerial Cable Systems Minimum Vertical Clearances for Aerial Cable Systems Aluminum Tapered Elliptical Brackets on Metal and Concrete Poles, Mounting Details Pole Wiring Diagram - 120V System Pole Wiring Diagram - 120/240V System Pole Wiring Diagram - 347/600V System Pole Wiring Diagram, Lighting Pole on Bridge Structure DIVISION WORK ON STRUCTURE Rigid PVC Junction Box, Type P Rigid PVC Junction Box, Type P Rigid PVC Junction Box, Type P Embedded Work Detail for Rigid PVC Junction Box, Type P3-1, for Use in Concrete Barrier Wall Expansion and Deflection Fitting Assembly for 50 and 75 mm Rigid Ducts Embedded Work in Structure, New Jersey Type Concrete Barrier Wall Embedded Work in Structure, Parapet Wall Underpass Luminaires Wall Mounted Installation Underpass Luminaire Ceiling Mounted Installation with Tee Bracket Tee Bracket for Ceiling Mounted Underpass Luminaire Wedge Mounting Bracket for Underpass Luminaire Support Bracket for Column Mounted Underpass Luminaire Underpass Luminaire Wiring Detail November 2014 Page 5
6 DIVISION PURCHASING S Distribution Assembly Legend Distribution Assembly, Cabinet Distribution Assembly, Equipment Layout Distribution Assembly Wiring Schematic Warning Signs for Electrical Equipment Warning Signs Outside Electrical Equipment Spun Concrete Pole m Spun Concrete Pole for TV Camera Mounting Steel Pole - Base Mounting Steel Pole, Base Mounted Without Gussets Steel Pole - Concrete Barrier Mounting Steel Pole, Concrete Barrier Base Mounted Without Gussets m and 2.7 m Steel Truss Bracket for Steel Poles m and 2.7 m Aluminum Tapered Elliptical Bracket Lamp Wattage Label for Luminaire Frangible Bases Aluminum Pole - Base Mounted Supply Control Cabinet Assembly Type 1, 120/240V, 100A, 1-Phase, 3-Wire Supply Control Cabinet Assembly Type 2, 120/208V, 100A, 3-Phase, 4-Wire Supply Control Cabinet Assembly Type 2, 347/600V, 100A, 3-Phase, 4-Wire Supply Control Cabinet Assembly Type 1 and 2, Enclosure Pole Mounting Bracket for Supply Control Cabinet Assembly Supply Control Cabinet Assembly Type 1 and 2, Dead Front Panels November 2014 Page 6
7 Supply Control Cabinet Assembly Type 1 and 2, 3-Point Door Latch Supply control Cabinet Assembly Type 1, 2, and 3, 3-Point Stainless Steel Door Handle Supply Control Cabinet Assembly Type 3, 120/240V, 100A, 1-Phase, 3-Wire Supply Control Cabinet Assembly Type 3, Enclosure Supply Control Cabinet Assembly Type 3, Dead Front Panels Supply Control Cabinet Assembly Type 3, 3-Point Door Latch Duct Hanger High Mast Lighting, 25, 30, and 35 m Octagonal Pole with Double Base Plate High Mast Lighting Pole, 25, 30, and 35 m 8-Sided Pole High Mast Lighting, 40 and 45 m Octagonal Pole with Double Base Plate High Mast Lighting Pole, 40 and 45 m 12-Sided Pole High Mast Lighting, 25, 30, and 35 m Round Pole with Double Base Plate High Mast Lighting, 40 and 45 m Round Pole with Double Base Plate High Mast Lighting Pole, Luminaire and Handhole Orientation High Mast Lighting Pole, Cable Holder, and Storage Hook Details High Mast Lighting Pole, Handhole Cover Hinges, Latches, and Padlock High Mast Lighting Pole, Nameplate Details High Mast Lighting Pole, Flood Light Luminaire Mounting Details High Mast Lighting Pole, Luminaire Support Ring High Mast Lighting Pole, Head Frame and Ring Assembly High Mast Lighting Pole, Luminaire Shroud High Mast Lighting Pole, Luminaire Shroud Details November 2014 Page 7
8 High Mast Lighting Pole, Internal Drive Raising and Lowering Equipment - List of Components High Mast Lighting Pole, Internal Drive Raising and Lowering Equipment - Layout High Mast Lighting Pole, Internal Motor and Winch Details High Mast Lighting Pole, Internal Drive Raising and Lowering Equipment, 347/600V, 3-Phase, Wiring Diagram High Mast Lighting Pole, Internal Drive Raising and Lowering Equipment, 120/240V, 1-Phase, Wiring Diagram High Mast Lighting Pole, External Drive Raising and Lowering Equipment - List of Components High Mast Lighting Pole, External Drive Raising and Lowering Equipment - Layout High Mast Lighting Pole, External Drive Raising and Lowering Equipment, 347/600V, 3-Phase, Wiring Diagram High Mast Lighting Pole, External Drive Raising and Lowering Equipment, 120/240V, 1-Phase, Wiring Diagram High Mast Lighting Pole, Double Base Plate Details High Mast Lighting Pole Anchorage Assembly Details for Double Base Plate High Mast Lighting Pole Anchorage Assembly Details DIVISION TRAFFIC SIGNALS mm Signal Arm and Signal Head mm Signal Arm Attachment to Poles Single Member Arm and Signal Head Aluminum Single Member Arm Attachment Details Traffic Signal, Adjustable Mid-Section Hanger Traffic Signal, Dual-End Hanger Traffic Signal, Pedestrian Head and Push Button Mounted on Pole Traffic Signal, Sectional Steel Poles with Primary and Secondary Signal Heads for Ramp Metering Pole Mounted Controller Cabinet Mounting Bracket for Pole Mounted Controller Cabinet November 2014 Page 8
9 Controller Cabinet on Pad Concrete Pad for Controller Cabinet Traffic Data Collection, Data Station, Traffic Counting Station Type Prefabricated Detector Loop Traffic Data Collection, Detector Loops, Heavy Duty Rubber Loop Detector Installation Details I Loop Detector Installation Details II Traffic Signal, Cushion Hanger Traffic Signal, Double Arm Bracket Traffic Signal Bracket for Mounting Pedestrian Instruction Sign on Pole Traffic Signal Equipment, Pole Wiring Diagram Signal Wiring for Pedestrian Facilities Signal Wiring Using 4/C Cable Connected Radially, 2 Phase Signal Wiring Using 12/C Cable Tapped, 2 to 8 Phase Signal Wiring Using 4/C and 12/C Cable Tapped, 2 to 8 Phase Signal Wiring Using 4/C Cable Connected Radially, 2 to 8 Phase Signal Wiring Using 4/C Cable Connected Radially, and 12/C Cable Tapped, 2 to 8 Phase Signal Wiring Using 19/C Cable Tapped, 2 to 8 Phase Signal Wiring Using 7/C Cable Connected Radially T-Intersection, 2 to 3 Phase Signal Wiring Using 4/C Cable Connected Radially T-Intersection, 2 Phase Splices for Traffic Signal Cable and Extra Low Voltage Cable Flasher Beacon and Downlight for Roadway Sign and Wiring Diagram November 2014 Page 9
10 Sign Light Assembly for Keep Right Sign and Wiring Diagram Flasher Beacons for Roadway Sign and Downlight and Wiring Diagram Aerial Traffic Signal Installation Aerial Flasher Beacon Installation Aerial Suspension Mounting Bracket, Signal Heads and Flashing Beacons Aerial Suspension Mounting Bracket, Emergency Pre-Emption Unit PVC Junction Box for Signal Cable Splicing Traffic Signal and Illumination Grounding System Traffic Signal System Equipment on Wooden or Concrete Poles, Overhead Wiring Installation Traffic Signal System Equipment on Wooden or Concrete Poles, Underground Wiring Installation Pole for Accessible Pedestrian Signal Push Button DIVISION 26 - SIGN LIGHTING CURRENTLY NO DRAWINGS November 2014 Page 10
General Symbols, Ducts and Cables
MUNICIPAL AND COMMON DIVISION 2000 ABBREVIATIONS 2009 11 2000.001 0 Abbreviations, General 2009 11 2011.101 0 General Symbols, Ducts and Cables 2009 11 2011.201 0 General Symbols, Maintenance Holes, Junction
General Symbols, Ducts and Cables
DIVISION 2000 ABBREVIATIONS 2009 11 2000.001 0 Abbreviations, General 2009 11 2011.101 0 General Symbols, Ducts and Cables 2009 11 2011.201 0 General Symbols, Maintenance Holes, Junction Boxes, Pads, and
Engineering Specifications February, 2004 Schedule H to Bylaw 7452, Subdivision Bylaw Page 105 ELECTRICAL DETAILS. base. base. base.
Schedule H to Bylaw 7452, Subdivision Bylaw Page 105 4.3.7 Electrical Details ELECTRICAL DETAILS MMCD Standard Detail Drawing Saanich Supplemental Specification E1.1 Concrete Base Index E1.2 Type A and
SUPPLEMENTAL DRAWINGS
CITY OF GREATER SUDBURY SUPPLEMENTAL DRAWINGS TO THE ONTARIO PROVINCIAL STANDARD DRAWINGS Rev: February 2012 CITY OF GREATER SUDBURY STANDARD DRAWINGS TABLE OF CONTENTS Greater Sudbury Standard Drawings
CONSTRUCTION SPECIFICATION FOR POLE ERECTION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2006 CONSTRUCTION SPECIFICATION FOR POLE ERECTION TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not Used 615.04
CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not Used 615.04
CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2008 (Reissued November 2010) CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03
TS 804 CABLES TABLE OF CONTENTS TRAFFIC SIGNAL EQUIPMENT POLE WIRING DIAGRAM LOCATIONS WITH CENTRE MEDIANS
TORONTO TRANSPORTATION January 2012 TS 804 CABLES TABLE OF CONTENTS 1. DRAWINGS TTD 804.001 TTD 804.002 TTD 804.003 TTD 804.005 TTD 804.006 TTD 804.007 TTD 804.010 TTD 804.015 TTD 804.020 TTD 804.025 TTD
Ontario Ministry of Transportation. Designated Sources of Material (DSM) Index
2 GRADING 2.35 Fill 2.35.30 Lightweight Fill Material 3 PAVEMENTS 3.05 Asphalt 3.05.10 Anti-Stripping Treatments (formerly Anti-stripping Additives) 3.05.22 Asphalt Cement, Performance Graded (PGAC) 3.05.25
CITY OF ROCKLIN STANDARD DRAWINGS
CITY OF ROCKLIN STANDARD DRAWINGS November 2016 Table of Contents Page # Section 1 Section 2 Section 3 General Notes and Review Boxes 01-01 Signature Blocks... 1 01-02 General Notes (Sheet 1 of 8)... 2
TS 805 POLES TTS CONSTRUCTION SPECIFICATION FOR POLE INSTALLATION TTS MATERIAL SPECIFICATION FOR STEEL POLES BASE MOUNTED
TORONTO TRANSPORTATION January 2012 TS 805 POLES TABLE OF CONTENTS 1. DRAWINGS TTD 805.001 POLE HANDHOLE ORIENTATION DETAILS TTD 805.005 WOOD POLE IN EARTH TTD 805.010 BACK GUY MOUNTING DETAILS TTD 805.015
LIST OF STANDARD DRAWINGS H2-9 - SERIES 9: Fencing, Guide Rails
LIST OF STANDARD DRAWINGS H-9 - SERIES 9: Fencing, Guide Rails # Title Drawing 900.0 Chain Link Security Fence Chain Link Fence - For Roadway Installations 900.0 Installation of Barbed Wire - For Chain
12/21/2018 WHAT S NEW SINCE What's New Since SPEC BOOK 2018 SPEC BOOK 2018 SPEC BOOK WHAT S NEW SINCE 2014
CHAPTER 2 STANDARD SPECIFICATIONS AND SPECIAL PROVISIONS 2545.1B & 2565.1B QUALIFICATION OF WORKERS The provisions of 1802 are hereby supplemented with the following: Signal and Lighting Certification:
1/5/2018 WHAT S NEW SINCE B & B QUALIFICATION OF WORKERS. What's New Since SPEC BOOK 2018 SPEC BOOK 2018 SPEC BOOK
CHAPTER 2 STANDARD SPECIFICATIONS AND SPECIAL PROVISIONS 2545.1B & 2565.1B QUALIFICATION OF WORKERS The provisions of 1802 are hereby supplemented with the following: Signal and Lighting Certification:
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 615 April 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not
2008 Interim Standard Sheet List For Use with the 2008 Imperial Road and Bridge Standards July, 2015
2008 Interim Standard Sheet List For Use with the 2008 Imperial Road and Bridge Standards July, 2015 The following is a complete list of special design IMPERIAL interim standard sheets that will be used
MATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR HIGHWAY LIGHTING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 2432 NOVEMBER 2015 MATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR HIGHWAY LIGHTING TABLE OF CONTENTS 2432.01 SCOPE 2432.02 REFERENCES
CONSTRUCTION SPECIFICATION FOR POLE ERECTION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 SEPTEMBER 1993 CONSTRUCTION SPECIFICATION FOR POLE ERECTION 615.01 SCOPE 615.02 REFERENCES 615.05 MATERIALS TABLE OF CONTENTS 615.05.01 Concrete.02
STANDARD DRAWINGS. September 2013 UPDATED FEBRUARY 2016
STANDARD DRAWINGS September 2013 UPDATED FEBRUARY 2016 CONSTRUCTION STANDARD DRAWINGS DIVISION 15 LIST OF DRAWINGS: 1. 01 2004-1 Rev. A - Concrete Standards General Outline and Reinforcement Notes 2. 01
ENGINEERS ESTIMATE MARYLAND STATE HIGHWAY ADMINISTRATION
ENGINEERS ESTIMATE The Engineer s Estimate is an important part of the overall design process. It is a determination of the construction costs for any given project. The estimate is then used for programming
Delivering Reliability. Electrical Vaults. Power & Energy-Underground Structures
A Delivering Reliability Electrical Vaults Power & Energy-Underground Structures A The Benefits of Precast Vaults Electrical vaults house power cables and transformers, and are a preferred alternative
CITY OF ROSEVILLE CONSTRUCTION STANDARDS - CST
CITY OF ROSEVILLE CONSTRUCTION STANDARDS - CST Abbreviations AB 1-3 Section 11 Purpose and Definitions 11-1 Purpose PD 1 11-2 Construction Practice PD 1 11-3 Definitions PD 1 Section 12 Construction Area
CS-21 STREET STRUCTURES TABLE OF CONTENTS
TABLE OF CONTENTS CS-21.0 Street Structures... 1 CS-21.1 Road Signs... 1 CS-21.2 Safety Barriers... 1 CS-21.3 Bollards and Removable Bollards... 1 CS-21.4 Pedestrian Barrier Rails and Handrails... 1 CS-21.5
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF SECTIONAL STEEL HIGH MAST LIGHTING POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 630 NOVEMBER 2011 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF SECTIONAL STEEL HIGH MAST LIGHTING POLES TABLE OF CONTENTS 630.01 SCOPE 630.02 REFERENCES
CHAPTER 11 CONDUITS AND FITTINGS
CONDUITS AND FITTINGS CHAPTER 11 CONDUITS AND FITTINGS The standards and requirements for conduits and fittings used for traffic control signal and lighting systems are presented in this chapter. 11.1
2008 Interim Standard Sheet List For Use With The 2008 Imperial Road and Bridge Standards October, 2014
2008 Interim Standard Sheet List For Use With The 2008 Imperial Road and Bridge Standards October, 2014 The following is a complete list of special design IMPERIAL interim standard sheets that will be
CONSTRUCTION SPECIFICATION FOR CABLE INSTALLATION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 604 NOVEMBER 2004 CONSTRUCTION SPECIFICATION FOR CABLE INSTALLATION TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
HALIFAX REGIONAL MUNICIPALITY MUNICIPAL DESIGN GUIDELINES
HALIFAX REGIONAL MUNICIPALITY MUNICIPAL DESIGN GUIDELINES 2013 PART B STANDARD DETAILS Municipal Design Guidelines Contents PART B: STANDARD DETAILS Municipal Roads/Streets HRM 1 HRM 2 HRM 3 HRM 4 HRM
Section 820. TRAFFIC SIGNALS
820.02 Section 820. TRAFFIC SIGNALS 820.01. Description. This work consists of providing required components to complete the following: A. Provide complete, operating traffic and pedestrian signals, span
B STEEL BEAM GUIDE RAIL - OPSS 552
B552-2 - - OPSS 552 552-2.1 GENERAL Steel Beam Guide Rail (SBGR) is a semi-rigid barrier system which restrains and redirects vehicles by a combination of beam bending (W-shaped steel section), tension,
B STEEL BEAM GUIDE RAIL - OPSS 721
B721-2 - - OPSS 721 721-2.1 GENERAL Steel Beam Guide Rail (SBGR) is a semi-rigid barrier system which restrains and redirects vehicles by a combination of beam bending (W-shaped steel section), tension,
TS 803 DUCTS DUCT INSTALLATION, PROTECTION AND MARKING WITHIN A TRENCH OPEN TRENCH DUCT INSTALLATION PROFILE
TORONTO TRANSPORTATION March 2012 TS 803 DUCTS TABLE OF CONTENTS 1. DRAWINGS TTD 803.001 TTD 803.010 DUCT INSTALLATION, PROTECTION AND MARKING WITHIN A TRENCH OPEN TRENCH DUCT INSTALLATION PROFILE 2. CONSTRUCTION
CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 MARCH 1993 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER 602.01 SCOPE 602.02 REFERENCES 602.05 MATERIALS TABLE OF CONTENTS
Drawing Modification Summary Effective:
Illinois Tollway Base Sheet Revisions Section M Base Sheet Drawings Drawing Modification Summary Effective: 03-31-2017 Roadway (RDY)-Series 400 M-RDY-408 Approach Slab, Mainline Sheet 3 Added slipforming
G2-0 List of Active Ministry of Transportation of Ontario Drawings (MTOD s)
G2-0 List of Active Ministry of Transportation of Ontario Drawings ( s) DIVISION 100 - ABBREVIATIONS 101.070 Legend - Markings 01/04/1994 04/01/1994 TOS/TO For use with Marking items. DIVISION 200 GRADING
CONSTRUCTION SPECIFICATION FOR EMBEDDED WORK IN STRUCTURES FOR ELECTRICAL SYSTEMS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 913 NOVEMBER 2006 CONSTRUCTION SPECIFICATION FOR EMBEDDED WORK IN STRUCTURES FOR ELECTRICAL SYSTEMS TABLE OF CONTENTS 913.01 SCOPE 913.02 REFERENCES
City of Redding Construction Standards Index
City of Redding Construction Standards Index A. Purpose and Reference Documents... A1 B. Modifications to the Standard Specifications for Public Works Construction (Greenbook)... B1 I. Streets Materials...
SECTION PATHWAYS FOR ELECTRONIC SAFETY AND SECURITY
SECTION 280528 - PATHWAYS FOR ELECTRONIC SAFETY AND SECURITY PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Metal conduits, tubing, and fittings. 2. Nonmetallic conduits, tubing, and fittings. 3.
SPECIAL SPECIFICATION 7191 Illumination
1993 Specifications For Routine Maintenance Contracts Only Houston District SPECIAL SPECIFICATION 7191 Illumination 1. Description. This Item shall govern for the preventive maintenance, repair and/or
Abbreviations, Building Descriptions Topography Plan Features, Monument Features
MUNICIPAL AND COMMON DIVISION 100 - ABBREVIATIONS 2010 11 100.010 4 Abbreviations, General A-C 2006 11 100.011 1 Abbreviations, General D-J 2009 11 100.012 2 Abbreviations, General L-R 2009 11 100.013
CONDUITS AND FITTINGS
CONDUIT AND FITTINGS Rigid Steel Conduit 3801 Rigid PVC Conduit 3803 HDPE Conduit 3803 Flexible Non Metallic Liquid Tight Conduit Type LFNC-B 3804 PVC Coated Urethane Lined Galvanized Rigid Steel Conduit
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 603 APRIL 2010 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS TABLE OF CONTENTS 603.01 SCOPE 603.02 REFERENCES 603.03 DEFINITIONS 603.04 DESIGN
GENERAL SPECIFICATION FOR ELECTRICAL WORK
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 106 NOVEMBER 2004 GENERAL SPECIFICATION FOR ELECTRICAL WORK TABLE OF CONTENTS 106.01 SCOPE 106.02 REFERENCES 106.03 DEFINITIONS 106.04 SUBMISSION
RESIDENTIAL QUICK REFERENCE
RESIDENTIAL QUICK REFERENCE PROVO CITY POWER STANDARDS ELECTRICAL ENGINEERING UPDATED: 2016 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION. 18" MIN. OF TAIL. (NEUTRAL CONDUCTOR MUST BE WHITE OR
CHAPTER 12 HANDHOLES, PULLING VAULTS, AND JUNCTION BOXES
CHAPTER 12 HANDHOLES, PULLING VAULTS, AND JUNCTION BOXES HANDHOLES, PULLING VAULTS, AND JUNCTION BOXES The standards and requirements for handholes, pulling vaults, and junction boxes are presented in
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 603 NOVEMBER 2017 (Formerly OPSS 603, November 2015) Note: The PROV published in November 2017 replaces OPSS 603 COMMON, November 2015 with no technical
City of St. Catharines Standard Drawings JULY Revised July 21, 2017 TES-ENG (SH)
City of St. Catharines Standard Drawings JULY 2017 Revised July 21, 2017 TES-ENG (SH) Roads Dwg No. Revision Standard Sidewalk Detail 110-2001 1 Monolithic Curb-Faced Sidewalk for Concrete Road 110-2002
Baseline Document Change Announcement
BDC16D-01 Page 1 of 7 New Jersey Department of Transportation 1035 Parkway Avenue, PO Box 600, Trenton, New Jersey 08625-0600 Baseline Document Change Announcement ANNOUNCEMENT: BDC16D-01 DATE: September
G2-0 List of Active Ministry of Transportation of Ontario Drawings (MTOD s)
G2-0 List of Active Ministry of Transportation of Ontario Drawings ( s) DIVISION 100 - ABBREVIATIONS 101.070 Legend - Pavement Markings 01/04/1994 04/01/1994 TOS/TO For use with Pavement Marking items.
OVERHEAD SERVICES - SECONDARY
OVERHEAD SERVICES - SECONDARY Contents - Overhead Services... O-1 General Requirements for Overhead Service... O-2 Names of Parts for Overhead Service... O-3 Service Attachment on an Unguyed Service Mast...
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 604 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
ROAD CLOSURE GATE PLAN ESTIMATED QUANTITIES CONCRETE FOOTINGS FOR S. D. DEPT. OF TRANSPORTATION DECEMBER 1996 ELEVATION CABLE TIE DOWN FOOTING
ADMIN. S 1 1 13 199 POST Anchor Bolts (4 Required) 1 Pole Base Plate Footing PLAN POST Chamfer on Footing ESTIMATED QUANTITIES ITEM UNIT QUANTITY Footing & Eyebolt Class M5 Concrete CU.YD. 0.5 The quantity
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 604 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF SIGN LUMINAIRES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 612 SEPTEMBER 1984 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF SIGN LUMINAIRES 612.01 SCOPE 612.02 REFERENCES 612.03 Not Used 612.04 Not Used
E. CONSTRUCTION PROCEDURES
E. CONSTRUCTION PROCEDURES The Project facilities would be constructed in accordance with established electric utility practices, best management practices, final engineering plans, CL&P s specifications
GENERAL SPECIFICATION FOR ELECTRICAL WORK
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 106 April 2017 GENERAL SPECIFICATION FOR ELECTRICAL WORK TABLE OF CONTENTS 106.01 SCOPE 106.02 REFERENCES 106.03 DEFINITIONS 106.04 DESIGN AND
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS TABLE OF CONTENTS 602.01 SCOPE 602.02 REFERENCES 602.03 DEFINITIONS
CONTRACT DESIGN, ESTIMATING AND DOCUMENTATION (CDED) MANUAL REVISION # 222
CONTRACT DESIGN, ESTIMATING AND DOCUMENTATION (CDED) MANUAL REVISION # 222 March 8, Significant changes have been made to Volumes 1, 2A, 2B, 3 (Electrical), and 4 (ATMS) of the CDED Manual as follows:
General Legend Details...100
SECTION 1 - ROADWAYS TABLE OF CONTENTS General Legend Details......100 Details Roadway Section......... 110 Residential Street Intersection.........115 Waterway and Waterway Transition Detail........116
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ROADWAY LUMINAIRES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 617 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ROADWAY LUMINAIRES TABLE OF CONTENTS 617.01 SCOPE 617.02 REFERENCES 617.03 DEFINITIONS
Review of Plans and Specs from a Constructability Perspective
Review of Plans and Specs from a Constructability Perspective The Executive Regional Manager and the Project Manager, with approval of the Director of Project Management, may request the Constructability
Draft. Not yet Approved
2016 Part 3.2.5 Recommended Design Criteria and Functional/Operating Guidelines for Overhead Bridge and Cantilever Structures and Placement of Grade Crossing Warning Devices Revised 2017 (8 Pages) A. Purpose
ENGINEERING DESIGN & IMPROVEMENT STANDARDS
ENGINEERING DESIGN & IMPROVEMENT STANDARDS 2016 Prepared by: Engineering Division For latest edition of these Improvement Standards, refer to City of Visalia website at: www.visalia.city/engineeringdocuments
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 602 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ELECTRICAL CHAMBERS TABLE OF CONTENTS 602.01 SCOPE 602.02 REFERENCES 602.03 DEFINITIONS
HIGH MAST CAMERA POLE ASSEMBLY GENERAL
10-3.24 HIGH MAST CAMERA POLE ASSEMBLY GENERAL The Contractor must furnish and install the following equipment for high mast camera pole assembly as described herein and as shown on the plans: 1. Camera
Electrical Standard Specifications and Standard Drawings
Utility Services Department 500 George Street North, Peterborough, Ontario, K9H 3R9 Transportation Division Telephone: 705-742-7771 Fax: 705-876-4621 Electrical Standard Specifications and Standard Drawings
All RED text must be removed from the special provisions prior to the special provisions being submitted for project letting.
This set of special provisions is put together as a standalone project where the District wants to construct a standalone temporary lighting system. If the District wants to construct a temporary lighting
Underground Exhaust System
Operation and Maintenance Manual Underground Exhaust MONOXIVENT - SOURCE CAPTURE SYSTEMS - info@ Oct. - 2015 Underground Duct Construction Standards 1. Dig trench depth to allow for minimum distance from
HANDHOLES, PULLING VAULTS AND JUNCTION BOXES
Handholes and pulling vaults perform several important functions: Provide drainage for the conduit system so that freezing water does not damage the conduit or wires. Provide a location for bending the
A. Product Data: For surface pathways, wireways and fittings, floor boxes, hinged-cover enclosures, and cabinets.
ALLIANT ENERGY CENTER PAVILIONS Project No. 2013 027 SECTION 27 05 28 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
Douglas County Traffic Signal Installation Guidelines (January 2013)
Douglas County Traffic Signal Installation Guidelines (January 2013) The following guidelines are minimum requirements for equipment installation. Section A. Poles and Foundations ( Wood, Concrete, Mast
SECTION MOTOR CONTROL CENTER
SECTION 16445 MOTOR CONTROL CENTER PART 1 GENERAL 1.01 DESCRIPTION A. This section covers the contract item Motor Control Center (MCC). The contract item includes demolition and removal of existing MCC;
Abbreviations, Building Descriptions Topography Plan Features, Monument Features
DIVISION 100 - ABBREVIATIONS 2010 11 100.010 4 Abbreviations, General A-C 2006 11 100.011 1 Abbreviations, General D-J 2009 11 100.012 2 Abbreviations, General L-R 2009 11 100.013 4 Abbreviations, General
Student Services & Classroom Addition
SECTION 260533 - RACEWAY AND BOXES FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes raceways, fittings, boxes, enclosures, cabinets, and track busway for electrical wiring.
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 603 NOVEMBER 2015 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS TABLE OF CONTENTS 603.01 SCOPE 603.02 REFERENCES 603.03 DEFINITIONS 603.04 DESIGN
CHAPTER 13 GROUNDING AND BONDING
GROUNDING AND BONDING CHAPTER 13 GROUNDING AND BONDING Grounding and bonding must be in accordance with Article 250 of the National Electrical Code (NEC). Bonding is defined in the NEC as the permanent
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF DUCTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.MUNI 603 NOVEMBER 2017 (Formerly OPSS 603, November 2015) Note: The MUNI implemented in November 2017 replaces OPSS 603 COMMON, November 2015 with no technical
[Type text] Heber Light & Power. Developers & Excavators. Electrical Service Requirements Manual
![[Type text] Heber Light & Power. Developers & Excavators. Electrical Service Requirements Manual](/thumbs/83/87082261.jpg "[Type text] Heber Light & Power. Developers & Excavators. Electrical Service Requirements Manual")
[Type text] Heber Light & Power Developers & Excavators Electrical Service Requirements Manual May 2017 E.1.1 - GENERAL REQUIREMENTS PURPOSE This section was prepared to aid developers, contractors, engineers
CORPORATION OF THE TOWN OF WHITBY
CORPORATION OF THE TOWN OF WHITBY PUBLIC WORKS DEPARTMENT ENGINEERING SECTION The Town of Whitby has adopted the Ontario Provincial Standards. They consist of the following: Ontario Provincial Standard
DIVISION 3 PAVEMENT (FLEXIBLE AND RIGID) CONSTRUCTION SPECIFICATIONS
OPS GENERAL CONDITIONS OF CONTRACT NOV 2006 General Conditions of Contract DIVISION 1 GENERAL S OCT 92 102 Weighing of Materials NOV 2004 106 Electrical Work NOV 2003 120 The Use of Explosives APR 2006
CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ROADWAY LUMINAIRES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 617 NOVEMBER 2013 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF ROADWAY LUMINAIRES TABLE OF CONTENTS 617.01 SCOPE 617.02 REFERENCES 617.03 DEFINITIONS
SECTION 1101 TRAFFIC SIGNALS AND APPURTENANCES END OF SECTION
SECTION 1101 SIGNALS AND APPURTENANCES PART 1 GENERAL 1.4 SUBMITTALS E. Submit warranty for all supplied material and workmanship for a period of two years from final acceptance. The warranty must state
Cutouts and Fuse Links Equipment to protect against faults and over-current conditions on power distribution systems. Open-Type Cutouts Linkbreak Cutouts Loadbreak Cutouts Cutout-Arrester Combinations
MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 26 ELECTRICAL SECTION RACEWAY AND BOXES FOR ELECTRICAL SYSTEMS
SECTION 260533 - RACEWAY AND BOXES FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes raceways, fittings, boxes, enclosures, and cabinets for electrical wiring. B. See Division
STREET LIGHTING GENERAL INFORMATION
SECTION 1102 STREET LIGHTING GENERAL INFORMATION These specifications are for street lighting that is to be dedicated to the public and maintained by the City of Meridian. Such installations require a
New Jersey Turnpike Authority
New Jersey Turnpike Authority DOCUMENT UPDATE REQUEST Forward to Assistant Chief Engineer, Design Initiator Russell Saputo, PE Submittal Date 6/21/16 Firm Stantec Consulting Services Inc. Telephone 201-587-9040
CONSTRUCTION SPECIFICATION FOR GROUNDING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 609 NOVEMBER 2001 CONSTRUCTION SPECIFICATION FOR GROUNDING TABLE OF CONTENTS 609.01 SCOPE 609.02 REFERENCES 609.03 DEFINITIONS - Not Used 609.04 DESIGN
LIST OF ACTIVE OPSSs
LIST OF ACTIVE OPSSs DIVISION 1 - GENERAL SPECIFICATIONS 100 PROV MTO General Conditions of Contract Nov 2016 Jan 12, 2017 102 COMM Weighing of Materials Oct 1992 Mar 17, 1994 106 PROV Electrical Work
CONSTRUCTION SPECIFICATION FOR TRAFFIC ACTUATION EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 623 JANUARY 1990 CONSTRUCTION SPECIFICATION FOR TRAFFIC ACTUATION EQUIPMENT 623.01 SCOPE 623.02 REFERENCES 623.05 MATERIALS TABLE OF CONTENTS 623.05.01
AREMA C&S Manual 2018 (Includes 2018 Revisions) Volume 4 Index SECTION 14 - ELECTRICAL DEVICES, FOUNDATIONS, HARDWARE
SECTION 14 - ELECTRICAL DEVICES, FOUNDATIONS, HARDWARE 14.1 Recommended Wire Connectors, Terminals 14.1.1 37-2 Recommended Design Criteria and Functional/Operating Guidelines for Solderless Crimp-Type
PART 1 COMMON FOR WATER & WASTEWATER CONSTRUCTION TITLE By Other Than Open Cut (Non-T.x.D.O.T. - Non Railroad) --- 101 Highway Crossing - All Wastewater Mains & Water Mains 12" and Smaller in Diameter.
H3-2 LIST OF ACTIVE ONTARIO PROVINCIAL STANDARD DRAWINGS Division 900 Fencing and Guide Rails
0911.1300 Type A, Installation 0911.1310 Type C, Installation 0911.1320 Tall Wall, Installation 0911.1400 Guide Rail System Concrete Barrier, Precast I-Lock Connection, Installation - Temporary and Permanent
B STEEL BEAM GUIDE RAIL - OPSS 721
B721-2 - - OPSS 721 721-2.1 GENERAL Steel Beam Guide Rail (SBGR) is a semi-rigid barrier system which restrains and redirects vehicles by a combination of beam bending (W-shaped steel section), tension,
EFFECTIVE DATE: November 1, 2011, unless a later date is cited at the end of a section. [ NMAC - Rp,
TITLE 14 CHAPTER 10 PART 4 HOUSING AND CONSTRUCTION ELECTRICAL CODES 2011 NEW MEXICO ELECTRICAL CODE 14.10.4.1 ISSUING AGENCY: The Construction Industries Division of the Regulation and Licensing Department.
NEC 2014 Code Changes
NEC 2014 Code Changes Articles 280.21-300.50 CHANGES FROM 2011 TO 2014 CODE ARE IN RED Chapter 2 - Wiring and Protection ARTICLE 280 Surge Arresters, Over 1000 volts II. Instillation III. Connecting Surge
PITTSBURGH TECHNOLOGY CENTER PUBLIC IMPROVEMENTS SITE PREPARATION CONTRACT NO. 11 BID TABULATION BID OPENING DATE: MARCH 11, 2008
BT-1 of 7 Clearing and Grubbing L.S. $50,000.00 $50,000.00 $5,335.00 $5,335.00 $14,560.00 $14,560.00 $20,000.00 $20,000.00 $10,600.00 $10,600.00 Class 1 Excavation 4300 C.Y. $20.00 $86,000.00 $15.00 $64,500.00
G2-0 LIST OF ACTIVE MTODs
G2-0 LIST OF ACTIVE MTODs DIVISION 100 - ABBREVIATIONS 101.070 Legend - Pavement Markings Apr 1, 1994 Jan 4, 1994 TOS/TO For use with Pavement Marking items. DIVISION 200- GRADING 219.101 Light Duty Straw