ANSI/NEMA WC ICEA S Standard for Control, Thermocouple Extension, and Instrumentation Cables

Size: px
Start display at page:

Download "ANSI/NEMA WC ICEA S Standard for Control, Thermocouple Extension, and Instrumentation Cables"

Transcription

1 Approved as an American National Standard ANSI Approval Date: October 31, 2014 ANSI/NEMA WC ICEA S Standard for Control, Thermocouple Extension, and Instrumentation Cables Prepared and Sponsored by: Insulated Cable Engineers Association, Inc. P.O. Box 1568 Carrollton, Georgia Published by: National Electrical Manufacturers Association 1300 North 17th Street, Suite 900 Rosslyn, Virginia (NEMA) and the Insulated Cable Engineers Association, Inc. (ICEA). All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions.

2

3 NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. The National Electrical Manufacturers Association (NEMA) and the Insulated Cable Engineers Association (ICEA) standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together persons who have an interest in the topic covered by this publication. While NEMA and ICEA administer the process and establish rules to promote fairness in the development of consensus, they do not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA and ICEA disclaim liability for personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA and ICEA disclaim and make no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA and ICEA do not undertake to guarantee the performance of any individual manufacturer or seller s products or services by virtue of this standard or guide. In publishing and making this document available, NEMA and ICEA are not undertaking to render professional or other services for or on behalf of any person or entity, nor are NEMA and ICEA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA and ICEA have no power, nor do they undertake to police or enforce compliance with the contents of this document. NEMA and ICEA do not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safetyrelated information in this document shall not be attributable to NEMA and ICEA and is solely the responsibility of the certifier or maker of the statement.

4

5 Page i Foreword The Standard for Control, Thermocouple Extension and Instrumentation Cables, ICEA S , NEMA WC , was developed by the Insulated Cable Engineers Association, Inc. (ICEA) and approved by the National Electrical Manufacturers Association (NEMA). Unless otherwise noted as Authorized Engineering Information, this standards publication has been approved by NEMA as a NEMA Standard. ICEA/NEMA standards are adopted in the public interest and are designed to eliminate misunderstanding between the manufacturer and the user and to assist users in selecting and obtaining the proper product for their particular needs. Existence of an ICEA/NEMA standard does not in any respect preclude the manufacture or use of products not conforming to the standard. The user of this standard is cautioned to observe any health or safety regulations and rules relative to the manufacture and use of cable made in conformity with this standard. This standard does not specify any specific frequencies for sampling for test purposes, cable products, or components. One program of sampling frequencies is given in Publication ICEA T /NEMA WC Requests for interpretation of this standard must be submitted in writing to the Insulated Cable Engineers Association, Inc., PO Box 1568, Carrollton, GA An official written interpretation will be provided, once approved by ICEA and NEMA. Suggestions for improvements gained in the use of this publication are welcomed by the Association.

6 Page ii Contents Condensed* Section GENERAL... 1 CONDUCTORS... 2 INSULATIONS... 3 SHIELDINGS AND COVERINGS... 4 ASSEMBLY, FILLERS, AND CONDUCTOR IDENTIFICATION... 5 TESTING AND TEST METHODS... 6 SPECIAL CONSTRUCTIONS... 7 ANNEXES... 8 *See next pages for a more detailed Table of Contents.

7 Page iii Contents Foreword... i Contents Condensed... ii Scope... vi Section 1 GENERAL GENERAL INFORMATION INFORMATION TO BE SUPPLIED BY PURCHASER... 2 Section 2 CONDUCTORS GENERAL WIRES, PHYSICAL AND ELECTRIC PROPERTIES COPPER CONDUCTORS Wires Solid Conductors Stranded Conductors Conductor DC Resistance per Unit Length Conductor Diameter CONDUCTORS FOR THERMOCOUPLE EXTENSION WIRES Conductor Material Size and Diameter Direct-current (DC) Resistance of Conductors Temperature Limits of Conductors Limits of Error of Conductors... 7 Section 3 INSULATIONS GENERAL MATERIALS THICKNESS SR PE PVC REQUIREMENTS Crosslinked Polyethylene (XLPE) Insulation, Type I and Type II Ethylene Propylene Rubber (EP) Insulation, Type I and Type II Ozone Resisting Silicone Rubber (SR) Insulation Chlorosulfonated Polyethylene (CSPE) Insulation Polyvinyl Chloride (PVC) Insulation Polyvinyl Chloride/Nylon (PVC/Nylon) Insulation Polyethylene (PE) Insulation Composite Insulation Styrene Butadiene Rubber (SBR) Insulation Thermoplastic Elastomer (TPE) Insulation, Type I and Type II Jacket over Insulation Repairs VOLTAGE TESTS Production Tests Acceptance Testing After Installation INSULATION RESISTANCE TYPE A FLAME TEST TYPE B FLAME TEST... 18

8 Page iv Section 4 SHIELDINGS AND COVERINGS SHIELDING GENERAL Shield Continuity Shield Isolation Metal Tape Shields Metal Braid Shields Metal Wire Shields JACKETS Thickness Requirements Binder METALLIC AND ASSOCIATED COVERINGS Types of Metallic Coverings Core Covering for Nonshielded and Nonjacketed Cable with Metallic Armor Interlocked Metal Tape Armor Galvanized Steel Wire Armor Flat Metal Tape Armor Continuously Corrugated Metal Armor Thermoplastic or Crosslinked Coverings over Metallic Armor Section 5 ASSEMBLY, FILLERS, AND CONDUCTOR IDENTIFICATION ASSEMBLY OF MULTIPLE CONDUCTOR CABLES Round Cables Subassemblies Flat Twin Cables FILLERS BINDERS CONDUCTOR IDENTIFICATION Section 6 TESTING AND TEST METHODS TESTING GENERAL CONDUCTOR TEST METHODS THICKNESS MEASUREMENTS FOR INSULATIONS AND NONMETALLIC JACKETS PHYSICAL AND AGING TESTS FOR INSULATIONS AND JACKETS Size and Preparation of Specimens Calculation of Test Specimen Area Physical Test Procedures TENSILE STRENGTH TEST TENSILE STRESS TEST ELONGATION TEST SET TEST AGING TESTS Test Specimens Air Oven Test Oil Immersion Test Hot Creep Test Heat Distortion for Insulated Conductors Heat Distortion for Thermoplastic Jackets Heat Shock for Thermoplastic Jackets Nylon Wrap Test OZONE RESISTANCE TEST THICKNESS OF COVERINGS ENVIRONMENTAL CRACKING ABSORPTION COEFFICIENT ACCELERATED WATER ABSORPTION General Electrical Method (EM-60)... 36

9 Page v Gravimetric Method COLD BEND FLAME TESTING Type A Type B VOLTAGE TESTS AC Voltage Test DC Voltage Test AC Spark Test INSULATION RESISTANCE Determination of Temperature Conversion Factors for Insulation Resistance SPECIFIC SURFACE RESISTIVITY SHIELD CONTINUITY SHIELD ISOLATION DIELECTRIC STRENGTH RETENTION Section 7 SPECIAL CONSTRUCTIONS LOW-SMOKE, HALOGEN-FREE (LSHF) CABLES Scope Conductors Insulation Assembly Shielding Jacket Coverings over Metallic Armor Tests C CABLE Scope Conductors Insulation Assembly Shielding Jacket Voltage Tests Section 8 ANNEXES Annex A INDUSTRY STANDARD REFERENCES (Normative) Annex B ADDITIONAL CONDUCTOR INFORMATION (Informative) Annex C REPRESENTATIVE VALUES OF TENSILE STRENGTH AND ELONGATION FOR NON-MAGNETIC ARMOR MATERIALS (Informative) Annex D FLAME TESTING FINISHED CABLE (Informative) Annex E CONDUCTOR IDENTIFICATION FOR CONTROL CABLES (Informative) Annex F RECOMMENDED BENDING RADII FOR CABLES (Informative) Annex G ACCEPTANCE TESTING AFTER INSTALLATION (Informative) Annex H OTHER TEST METHODS FOR INSTRUMENTATION CABLES (Informative)... 69

10 Page vi Scope This standard applies to materials, construction, and testing of multiconductor control, thermocouple extension, and instrumentation cables rated up to and including 125 o C. Control cables are multiconductor cables that convey electrical signals used for monitoring or controlling electrical power systems and their associated processes. Control cables convey signals between devices interfaced directly with the electrical power system, such as current transformers, potential transformers, relays, switches, and meters. Instrumentation cables and thermocouple extensions are multiconductor cables that convey lowenergy electrical signals (circuits that are inherently power limited) used for monitoring or controlling electrical power systems and their associated processes. Instrumentation cables and thermocouple extensions convey signals from process monitors to process analyzers (usually electronic equipment) and from the analyzers to control equipment in the electric power system. Construction details and test requirements for cables rated above 125 o C can be found in the NEMA HP-100 series of standards.

ANSI/NEMA WC 71 ICEA S Nonshielded Cables Rated V for Use in the Distribution of Electric Energy

ANSI/NEMA WC 71 ICEA S Nonshielded Cables Rated V for Use in the Distribution of Electric Energy Approved as an American National Standard ANSI Approval Date: June 10, 2014 ANSI/NEMA WC 71 ICEA S-96-659-2014 Nonshielded Cables Rated 2001-5000 V for Use in the Distribution of Electric Energy Prepared

More information

ICEA STANDARD FOR DISTRIBUTION FRAME-WIRE TECHNICAL REQUIREMENTS. Published By INSULATED CABLE ENGINEERS ASSOCIATION, INC. Post Office Box 1568

ICEA STANDARD FOR DISTRIBUTION FRAME-WIRE TECHNICAL REQUIREMENTS. Published By INSULATED CABLE ENGINEERS ASSOCIATION, INC. Post Office Box 1568 ICEA STANDARD FOR DISTRIBUTION FRAME-WIRE TECHNICAL REQUIREMENTS Published By INSULATED CABLE ENGINEERS ASSOCIATION, INC. Post Office Box 1568 Carrollton, GA 30112, U.S.A. 2011 Approved July 20, 2011 by

More information

STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV. Approved by AMERICAN NATIONAL STANDARDS INSTITUTE.

STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV. Approved by AMERICAN NATIONAL STANDARDS INSTITUTE. ANSI/ICEA S-108-720-2012 STANDARD FOR EXTRUDED INSULATION POWER CABLES RATED ABOVE 46 THROUGH 345 KV Approved by AMERICAN NATIONAL STANDARDS INSTITUTE November 27, 2012 Publication # ANSI/ICEA S-108-720-2012

More information

ANSI C (R2002, R2012) Reaffirmation of ANSI C (R2002) American National Standard. Thermal Demand Meters

ANSI C (R2002, R2012) Reaffirmation of ANSI C (R2002) American National Standard. Thermal Demand Meters Reaffirmation of ANSI C12.6-1978 (R2002) American National Standard Thermal Demand Meters American National Standard Thermal Demand Meters Secretariat: National Electrical Manufacturers Association Approved

More information

STANDARD FOR. BROADBAND TWISTED PAIR CABLE AIRCORE, POLYOLEFlN INSULATED, COPPER CONDUCTOR TECHNICAL REQUIREMENTS

STANDARD FOR. BROADBAND TWISTED PAIR CABLE AIRCORE, POLYOLEFlN INSULATED, COPPER CONDUCTOR TECHNICAL REQUIREMENTS STANDARD FOR BROADBAND TWISTED PAIR CABLE AIRCORE, POLYOLEFlN INSULATED, COPPER CONDUCTOR TECHNICAL REQUIREMENTS Published By INSULATED CABLE ENGINEERS ASSOCIATION, INC. Post Office Box 1568 Carrollton,

More information

IEEE 1580 Type P MOR Polyrad XT-125 Multi Conductor

IEEE 1580 Type P MOR Polyrad XT-125 Multi Conductor TABLE OF CONTENTS SECTION SUBJECT PAGE I. SCOPE...1 II. APPLICABLE DOCUMENTS...1 III. CONDUCTOR...2 IV. SEPARATOR...2 V. INSULATION...2 A. Physical Properties...2 B. Electrical Properties...3 C. Qualification

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 60502-1 Second edition 2004-04 Power cables with extruded insulation and their accessories for rated voltages from 1 kv (U m = 1,2 kv) up to 30 kv (U m = 36 kv) Part 1: Cables

More information

UNIFIED FACILITIES GUIDE SPECIFICATIONS

UNIFIED FACILITIES GUIDE SPECIFICATIONS USACE / NAVFAC / AFCEC / NASA UFGS-26 05 19.10 10 (May 2016) ----------------------------------- Preparing Activity: USACE Superseding UFGS-26 05 19.00 10 (November 2008) UNIFIED FACILITIES GUIDE SPECIFICATIONS

More information

NEMA Standards Publication NEMA/MITA 1. Good Refurbishment Practices for Medical Imaging Equipment

NEMA Standards Publication NEMA/MITA 1. Good Refurbishment Practices for Medical Imaging Equipment NEMA Standards Publication NEMA/MITA 1 Good Refurbishment Practices for Medical Imaging Equipment Published by: National Electrical Manufacturers Association 1300 North 17 th Street, Suite 900 Rosslyn,

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD IEC 60502-2 Second edition 2005-03 Power cables with extruded insulation and their accessories for rated voltages from 1 kv (U m = 1,2 kv) up to 30 kv (U m = 36 kv) Part 2: Cables

More information

AWS D14.3/D14.3M:2010 An American National Standard. Specification for Welding Earthmoving, Construction, and Agricultural Equipment

AWS D14.3/D14.3M:2010 An American National Standard. Specification for Welding Earthmoving, Construction, and Agricultural Equipment An American National Standard Specification for Welding Earthmoving, Construction, and Agricultural Equipment An American National Standard Approved by the American National Standards Institute May 26,

More information

Section ARMORED MEDIUM VOLTAGE CABLES SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR

Section ARMORED MEDIUM VOLTAGE CABLES SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR PART 1 - GENERAL Section 26 05 15 SHIELDED 3 CONDUCTOR POWER CABLE - INTERLOCKED ARMOR 1.1 Cable shall be 15 kv, shielded, three conductor with ground, stranded copper, with continuously welded and corrugated

More information

DETAIL SPECIFICATION SHEET CABLE, ELECTRICAL, -20 C TO +105 C, 1000 VOLTS, TYPE LSFSGU

DETAIL SPECIFICATION SHEET CABLE, ELECTRICAL, -20 C TO +105 C, 1000 VOLTS, TYPE LSFSGU INCH-POUND MIL-DTL-24643/17F 1 October 2009 SUPERSEDING MIL-DTL-24643/17E 22 August 2002 DETAIL SPECIFICATION SHEET CABLE, ELECTRICAL, -20 C TO +105 C, 1000 VOLTS, TYPE LSFSGU This specification is approved

More information

Glossary Of Terms M-1

Glossary Of Terms M-1 Glossary Of Terms ANSI - American National Standards Institute. Armor - A sheath, serving, braid or other layer of metal applied over a cable to increase its mechanical protection. ARR - Association of

More information

PROJECT MANAGEMENT BODY OF KNOWLEDGE

PROJECT MANAGEMENT BODY OF KNOWLEDGE A Guide to the PROJECT MANAGEMENT BODY OF KNOWLEDGE Third Edition (PMBOK Guide) Project Management Institute A Guide to the Project Management Body of Knowledge Third Edition (PMBOK Guide) an American

More information

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD. ANSI/SCTE (Formerly IPS SP 100)

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD. ANSI/SCTE (Formerly IPS SP 100) ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 15 2006 (Formerly IPS SP 100) Specification for Trunk, Feeder and Distribution Coaxial Cable NOTICE The Society

More information

PROForms. Specifications SECTION FIBERGLASS REINFORCED POLYMER (FRP) PULTRUDED PRODUCTS

PROForms. Specifications SECTION FIBERGLASS REINFORCED POLYMER (FRP) PULTRUDED PRODUCTS PROForms Specifications SECTION 06600 FIBERGLASS REINFORCED POLYMER (FRP) PULTRUDED PRODUCTS Disclaimer BEDFORD REINFORCED PLASTICS INC. disclaims liability for any personal injury, property or other damages

More information

600 VOLT 600V, 3 CONDUCTOR (WITH GROUND), FR-EPR OR FR-XLPE INSULATION, PVC JACKET SPECIFICATIONS (FLAME RETARDANT POWER CABLE) (UL TYPE TC-ER) TYPE C3 SPEC 70.0100 PROJECT 196116 REFERENCE: LATEST EDITIONS

More information

Una e mpre sa Vi akab l e GLOSSARY.

Una e mpre sa Vi akab l e GLOSSARY. GLOSSARY www.centelsa.com.co CONDUCTORS Cu Copper conductors. CuSn Tinned copper conductor. ACDSR Rectangular soft bare copper wire. ACDSRP Paper insulated rectangular soft bare copper wire. ACDD Bare

More information

CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE

CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 604 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used

More information

*** Supercedes: BECO E and COM , , & ***

*** Supercedes: BECO E and COM , , & *** 7/27/09 Page 1 of 9 R5 *** Supercedes: BECO E2.9-27.4 and COM 1-0696, 2-0196, & 5-0385 *** 1.0 Scope #2 AWG to 1000 KCMIL CONCENTRIC NEUTRAL JACKETED CABLES RATED 5-35 kv These Specifications cover single

More information

AWS D9.1/D9.1M:2018 An American National Standard. Sheet Metal Welding Code

AWS D9.1/D9.1M:2018 An American National Standard. Sheet Metal Welding Code An American National Standard Sheet Metal Welding Code An American National Standard Approved by the American National Standards Institute September 29, 2017 Sheet Metal Welding Code 7th Edition Supersedes

More information

Standard of Practice - Campus Electrical Distribution System

Standard of Practice - Campus Electrical Distribution System A26.3 Standard of Practice - Campus Electrical Distribution System NOTE: Significant revisions or additions to the previous standards are highlighted in italics. GENERAL Designers shall verify that all

More information

WHITE PAPER Flex Life vs Flexibility

WHITE PAPER Flex Life vs Flexibility WHITE PAPER Flex Life vs Flexibility The design criteria for both flex life and flexibility is the same but the properties and application of the elements can be vastly different. The design elements are

More information

U.V resistance UL Sunlight Resistance. Flame retardant IEC

U.V resistance UL Sunlight Resistance. Flame retardant IEC Cable for underground power distribution and subtransmission. Description Application Underground power distribution and subtransmission. As transformer feeders in substations. In power plants, industrial

More information

Construction guideline

Construction guideline 1/6 1) SUMMARY OF ABBREVIATIONS FOR CABLE CONSTRUCTION ELEMENTS MSR - : EUPEN code for INSTRUMENTATION CABLES JE - : cable for INDUSTRIAL ELECTRONICS RD - : cable for CONTROL SYSTEMS INSULATION MATERIALS:

More information

Title: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards

Title: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards Change History Date Description of Change Pages / Sections Modified Change Approver Initials 6/15/16 Updated division section from 16124 to 2605 - mgl44 13, removed references to other section 10/17/14

More information

AWS D8.2M:2017 An American National Standard. Specification for Automotive Weld Quality Resistance Spot Welding of Aluminum

AWS D8.2M:2017 An American National Standard. Specification for Automotive Weld Quality Resistance Spot Welding of Aluminum An American National Standard Specification for Automotive Weld Quality Resistance Spot Welding of Aluminum An American National Standard Approved by American National Standards Institute March 9, 2017

More information

Conductor Shield A combination of semi-conducting tape and extruded thermosetting semi-conducting material meeting UL 1309, IEEE 1580 and UL1072.

Conductor Shield A combination of semi-conducting tape and extruded thermosetting semi-conducting material meeting UL 1309, IEEE 1580 and UL1072. 37-105VFD MMV-VFD Power Cable Three : kv - 15kV 133% Level Rated 90 C s (3) Soft annealed flexible stranded tinned copper per IEEE 150 Table 11. Extruded thermosetting 90 C Ethylene Propylene Rubber (EPR),

More information

P.V.C. INSULATED ALUMINIUM SERVICE MAIN WIRE-FINISHED PRODUCT

P.V.C. INSULATED ALUMINIUM SERVICE MAIN WIRE-FINISHED PRODUCT CEB SPECIFICATION 005-1: 2012 P.V.C. INSULATED ALUMINIUM SERVICE MAIN WIRE-FINISHED PRODUCT CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 0953 Fax: +94 11 232 3935 CONTENTS PAGE 1. Scope 03

More information

NUCLEAR POWER CORPORATION OF INDIA LTD. (A GOVT. OF INDIA ENTERPRISE) SPECIFICATION NO.PB-E-542/REV. No.0

NUCLEAR POWER CORPORATION OF INDIA LTD. (A GOVT. OF INDIA ENTERPRISE) SPECIFICATION NO.PB-E-542/REV. No.0 REVISION NO. 0 NUCLEAR POWER CORPORATION OF INDIA LTD. (A GOVT. OF INDIA ENTERPRISE) SPECIFICATION NO.PB-E-542/REV. No.0 PAGE NO. 1 OF 24 DATE OF ISSUE (MONTH/YEAR) TOTAL NO. OF PAGES (Including cover

More information

MBG HEAVY DUTY METAL BAR GRATING MANUAL. MBG Metal Bar Grating Division of THE NATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS

MBG HEAVY DUTY METAL BAR GRATING MANUAL. MBG Metal Bar Grating Division of THE NATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS AMERICAN NATIONAL STANDARD ANSI/NAAMM MBG 532 00 ANSI/NAAMM MBG 532-00 November 14, 2000 5 GRATINGS HEAVY DUTY METAL BAR GRATING MANUAL FOURTH EDITION November 14, 2000 ANSI/NAAMM MBG 532-00 5 GRATINGS

More information

America s Wire Company

America s Wire Company America s Wire Company Dear Customer, We re pleased to provide you with our latest product catalog featuring many cables stocked in our warehouse located in Austin, Texas plus a backup inventory of products

More information

Your Partner for Custom Interconnectivity Solutions. ISO 9001 AS9100C ISO ISO Qualified

Your Partner for Custom Interconnectivity Solutions. ISO 9001 AS9100C ISO ISO Qualified Your Partner for Custom Interconnectivity Solutions ISO 9001 AS9100C ISO 13485 ISO 17025 Qualified LEMO Precision Custom Connection Solutions The Original Push-Pull Connector Seven Decades of Expertise

More information

Engineering Data for Copper and Aluminum Conductor Electrical Cables

Engineering Data for Copper and Aluminum Conductor Electrical Cables 2018 Edition Engineering Data for Copper and Aluminum Conductor Electrical Cables THE OKONITE COMPANY Okonite Cables...A higher Standard! The Okonite Company, 2018 Okonite Cables Table of Contents SECTION

More information

ISO/IEC INTERNATIONAL STANDARD. Systems and software engineering System life cycle processes IEEE

ISO/IEC INTERNATIONAL STANDARD. Systems and software engineering System life cycle processes IEEE INTERNATIONAL STANDARD ISO/IEC 15288 IEEE Std 15288-2008 Second edition 2008-02-01 Systems and software engineering System life cycle processes Ingénierie des systèmes et du logiciel Processus du cycle

More information

DESIGN GUIDELINES WIRING AND CONDUITS PAGE 1 of 7

DESIGN GUIDELINES WIRING AND CONDUITS PAGE 1 of 7 DESIGN GUIDELINES WIRING AND CONDUITS PAGE 1 of 7 1.1. REFERENCE STANDARDS 1.1.1. Publications listed below (including amendments, addenda, revisions, supplements and errata) form a part of this specification

More information

15 kv EPR Insulated, Jacketed, URD Cable

15 kv EPR Insulated, Jacketed, URD Cable 15 kv EPR Insulated, Jacketed, URD Cable 1000 kcm Copper Conductor with Tape Shield Page 1 of 11 Table Of Contents 1 GENERAL... 3 2 STANDARDS... 3 3 APPROVED CABLE MANUFACTURERS... 3 4 REEL SPECIFICATIONS...

More information

PT. KABELINDO MURNI Tbk SHIPBOARD CABLE WIRE AND CABLE MANUFACTURER. No. EMS No. OSH No. QCS 00152

PT. KABELINDO MURNI Tbk SHIPBOARD CABLE WIRE AND CABLE MANUFACTURER. No. EMS No. OSH No. QCS 00152 PT. KABELINDO MURNI Tbk WIRE AND CABLE MANUFACTURER No. QCS 00152 No. OSH 00971 No. EMS 00151 Introduction of company The Company s history was marked by the founding of PT. Kabel Indonesia (Kabelindo)

More information

3M Round, Shielded/Jacketed, Flat Cable.050" 28 AWG Stranded, Mass Terminatable, PVC/PVC 3659 Series

3M Round, Shielded/Jacketed, Flat Cable.050 28 AWG Stranded, Mass Terminatable, PVC/PVC 3659 Series M Round, Shielded/Jacketed, Flat Cable.050" 28 AWG Stranded, Mass Terminatable, PVC/PVC 659 Series Round construction permits easier routing 28 AWG wire on.050 inch pitch permits mass termination to broad

More information

PERFORMANCE SPECIFICATION SHEET

PERFORMANCE SPECIFICATION SHEET METRIC MIL-PRF-85045/21 26 July 1999 PERFORMANCE SPECIFICATION SHEET CABLE, FIBER OPTIC, EIGHT FIBERS, ENHANCED PERFORMANCE, CABLE CONFIGURATION TYPE 2 (OFCC), FOR SUBMARINE OUTBOARD USE ONLY (NOT FOR

More information

NEMA Standards Publication ANSI/NEMA PB

NEMA Standards Publication ANSI/NEMA PB ANSI Approval Date October 14, 2003 NEMA Standards Publication ANSI/NEMA PB 1.1-2002 General Instructions for Proper Installation, Operation, and Maintenance of Panelboards Rated 600 Volts or Less Published

More information

SECTION INSULATED WIRE AND CABLE

SECTION INSULATED WIRE AND CABLE SECTION 16120 INSULATED WIRE AND CABLE PART 1 GENERAL 1.01 DESCRIPTION A. This section covers the contract item Insulated Wire and Cable, which includes the following items with accessories, and appurtenances:

More information

History of Cable Systems HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES. Nigel Hampton

History of Cable Systems HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES. Nigel Hampton HISTORICAL OVERVIEW OF MEDIUM & HIGH VOLTAGE CABLES Nigel Hampton Copyright GTRC 2012 Objective To present the evolution of cables in time to understand the lessons from the past: the legacy problems and

More information

D8.14M:2017 An American National Standard. Specification for Automotive Weld Quality Arc Welding of Aluminum

D8.14M:2017 An American National Standard. Specification for Automotive Weld Quality Arc Welding of Aluminum An American National Standard Specification for Automotive Weld Quality Arc Welding of Aluminum An American National Standard Approved by the American National Standards Institute August 18, 2017 Specification

More information

Product Specifications

Product Specifications Product Specifications Bedford Standard Ladders Disclaimer BEDFORD REINFORCED PLASTICS INC. disclaims liability for any personal injury, property or other damages of any nature whatsoever, whether special,

More information

Electrical Conductors

Electrical Conductors Electrical Conductors Course No: E02-005 Credit: 2 PDH A. Bhatia Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980 P: (877) 322-5800 F: (877) 322-4774 info@cedengineering.com

More information

SECTION LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES (24 Volt AC/DC or Less)

SECTION LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES (24 Volt AC/DC or Less) SECTION 260523 LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES (24 Volt AC/DC or Less) PART 1 - GENERAL 1.1 SUMMARY A. Related Documents: 1. Drawings and general provisions of the Subcontract apply

More information

MEDIUM VOLTAGE XLPE INSULATED POWER CABLES [6.35/11kV Copper XLPE Three-Core HDPE Sheathed]

MEDIUM VOLTAGE XLPE INSULATED POWER CABLES [6.35/11kV Copper XLPE Three-Core HDPE Sheathed] [6.35/11kV Copper XLPE Three-Core HDPE Sheathed] APPLICATION Mostly used as feeder electric cable for power distribution network such as power supply station, substation, switching system etc. They are

More information

TYPE TEST REPORT OF 11 KV 3 x 240 mm² CU/XLPE/SWA/PVC CABLE. Kinectrics International Inc. Report No.: K RC-0001-R00.

TYPE TEST REPORT OF 11 KV 3 x 240 mm² CU/XLPE/SWA/PVC CABLE. Kinectrics International Inc. Report No.: K RC-0001-R00. To: National Cables Industry P.O Box 27472 Al Dhaid Road, Al Sajja Industrial Area Sharjah U.A.E TYPE TEST REPORT OF 11 KV 3 x 240 mm² CU/XLPE/SWA/PVC CABLE Kinectrics International Inc. Report No.: K-422341-RC-0001-R00

More information

3M Thermal Bonding Film 588

3M Thermal Bonding Film 588 Technical Data March 2015 3M Thermal Bonding Film 588 Product Description 3M Thermal Bonding Film 588 is a high strength, flexible, nitrile phenolic based thermosetting adhesive film. It can be heat or

More information

Welding Accessories

Welding Accessories Welding Accessories www.airliquide.ca 1-800-817-7697 Welding Accessories BLUESHIELD Welding Cables Blueshield Welding Cables: Excellent flexibility (stays flexible at -50 C) Abrasion resistant Oil, solvent

More information

3M Cold Shrink Silicone Rubber Connector Insulators 8440 Series

3M Cold Shrink Silicone Rubber Connector Insulators 8440 Series 3M Cold Shrink Silicone Rubber Connector Insulators 8440 Series Data Sheet May 2014 Product Description 3M Cold Shrink Connector Insulators 8440 Series are open-ended, silicone rubber, tubular sleeves.

More information

PILC Replacement: Getting the Lead Out

PILC Replacement: Getting the Lead Out PILC Replacement: Getting the Lead Out Spring Cincinnati, OH April 30, 2003 Page 1 PILC IS GREAT! Low Profile High Fault Current Capability on Shield High Degree of Water Blocking So why shouldn t you

More information

Ceramic plumbing fixtures ASME A / CSA B

Ceramic plumbing fixtures ASME A / CSA B Ceramic plumbing fixtures ASME A112.19.2-2013/ CSA B45.1-13 Legal Notice for Harmonized Standard Jointly Developed by ASME and CSA Group Intellectual property rights and ownership As between American Society

More information

VELCRO brand Adhesives. p re s s u re sensitive, fire re t a rd a n t, solve n t and heat ac t i v a t e d

VELCRO brand Adhesives. p re s s u re sensitive, fire re t a rd a n t, solve n t and heat ac t i v a t e d VELCRO brand Adhesives p re s s u re sensitive, fire re t a rd a n t, solve n t and heat ac t i v a t e d VELCRO brand Adhesives VELCRO brand products are available with a variety of adhesives to best

More information

Heritage Quality Performance

Heritage Quality Performance FEP FEATURES AND PROPERTIES Heritage Quality Performance Extruded, FEP insulated, high voltage wire and cable offers exceptional dielectric strength without the disadvantages common to equally rated silicone

More information

Profile No.: 4 NIC Code: ELECTRICAL CABLES (SINGLE AND MULTICORE)

Profile No.: 4 NIC Code: ELECTRICAL CABLES (SINGLE AND MULTICORE) Profile No.: 4 NIC Code: 27320 ELECTRICAL CABLES (SINGLE AND MULTICORE) 1. INTRODUCTION: Electrical Cables and wires are used for power distribution in electrical systems in housing sector as well as in

More information

Evaluation of Aluminum Cable Presentation for IEEE OCS September 14, 2011 Breck Booker, Southwire

Evaluation of Aluminum Cable Presentation for IEEE OCS September 14, 2011 Breck Booker, Southwire Evaluation of Aluminum Cable Presentation for IEEE OCS September 14, 2011 Breck Booker, Southwire Today s Topics Brief Overview of Southwire In-depth Discussion on Aluminum Characteristics Discussion of

More information

Agilent 16047D Test Fixture

Agilent 16047D Test Fixture Agilent 16047D Test Fixture Operation and Service Manual Third Edition Agilent Technologies Japan, Ltd. Agilent PN 16047-90300 May 2000 Printed in Japan Notices The information contained in this document

More information

Section 7 Cutting Fusible PVC Pipe

Section 7 Cutting Fusible PVC Pipe 7.0 Recommended practices for working with and handling bell and spigot PVC pipe apply to Fusible PVC pipe. However, lengths of Fusible PVC pipe, joined by butt fusion, are subject to additional stresses

More information

DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR

DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR INCH-POUND 10 December 1997 SUPERSEDING MIL-C-27500G 23 FEB. 1990 DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR

More information

Trex Wood-Polymer Composite Lumber

Trex Wood-Polymer Composite Lumber Evaluation Report CCMC 13125-R MASTERFORMAT 06 73 14.01 Issued 2003-06-24 Re-evaluated 2007-07-20 Revised 2009-01-06 Re-evaluation due 2010-06-24 Re-Evaluation in Progress Trex Wood-Polymer Composite Lumber

More information

7. EXTENSION LEADS AND COMPENSATING CABLE

7. EXTENSION LEADS AND COMPENSATING CABLE 7. EXTENSION LEADS AND COMPENSATING CABLE 7.1 INTRODUCTION : It is often desirable to connect a thermocouple probe, as a part of a very long circuit from the sensor itself to a remote reference unit and/or

More information

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for Underground Enclosure Integrity

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for Underground Enclosure Integrity ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 77 2007 Specification for Underground Enclosure Integrity NOTICE The Society of Cable Telecommunications Engineers

More information

Agilent 16034E Test Fixture

Agilent 16034E Test Fixture Agilent 16034E Test Fixture Operation and Service Manual Third Edition Agilent PN 16034-90041 December 1999 Printed in: Japan Notices The information contained in this document is subject to change without

More information

Evaluation Report CCMC R Trex Transcend Decking

Evaluation Report CCMC R Trex Transcend Decking Evaluation Report CCMC 13125-R Trex Transcend Decking MasterFormat: 06 73 14.01 Evaluation issued: 2003-06-24 Re-evaluated: 2017-04-13 Re-evaluation due: 2019-06-24 1. Opinion It is the opinion of the

More information

This section applies to the design and installation relating to wire and cable systems and terminations. 16G Figure 1 16G Figure 2

This section applies to the design and installation relating to wire and cable systems and terminations. 16G Figure 1 16G Figure 2 Wire, Cable and Terminations Basis of Design This section applies to the design and installation relating to wire and cable systems and terminations. Design Criteria Medium Voltage Review and modify the

More information

Switch-Tek. LV41 & LV42 Series Manual. Sump Float Level Switches

Switch-Tek. LV41 & LV42 Series Manual. Sump Float Level Switches Switch-Tek Sump Float Level Switches LV41 & LV42 Series Manual LV41 Series Shown LV42 Series Shown Flowline, Inc. 10500 Humbolt Street, Los Alamitos, CA 90720 p 562.598.3015 f 562.431.8507 w flowline.com

More information

Accelerated Aging Tests for MV Cables

Accelerated Aging Tests for MV Cables Accelerated Aging Tests for MV Cables Educational Session Fall ICC 2011 Denver, CO Acknowledgments: Rick Hartlein-NEETRAC Lauri Hiivala - Teksavvy Ram Ramachandran Dow Electrical & Telecommunications Dow

More information

INDUSTRIAL ATTACK 800

INDUSTRIAL ATTACK 800 ! INDUSTRIAL ATTACK 800 SPECIFICATION FOR 1, 1½, 1¾", 2, 2½", & 3 DOUBLE JACKET INDUSTRIAL FIRE HOSE POLYESTER FIBER CONSTRUCTION PLAIN WHITE OUTSIDE JACKET OR ULTRA-SHIELD IMPREGNATED OUTSIDE JACKET EPDM

More information

Cables for Railway Signalling Applications General Requirements

Cables for Railway Signalling Applications General Requirements Discipline: Engineering (Signalling) Category: Procedure Cables for Railway Signalling Applications General Requirements ESA-11-01 Applicability ARTC Network Wide Primary Source ESA-02-01 Document Status

More information

SCHEDULE ' A ' TECHNICAL SPECIFICATION FOR L.T.PVC POWER AND CONTROL CABLES FOR DISTRIBUTION NETWORK IN MAHARASHTRA

SCHEDULE ' A ' TECHNICAL SPECIFICATION FOR L.T.PVC POWER AND CONTROL CABLES FOR DISTRIBUTION NETWORK IN MAHARASHTRA SCHEDULE ' A ' TECHNICAL SPECIFICATION FOR L.T.PVC POWER AND CONTROL CABLES FOR DISTRIBUTION NETWORK IN MAHARASHTRA (SPECIFICATION NO.MM/I/LTPVC & CONTROL/2006) MAHARASHTRA STATE ELECTRICITY DISTRIBUTION

More information

ELE-3COP-256 Title Hand Cable Laying.

ELE-3COP-256 Title Hand Cable Laying. Before starting work please read this document carefully and note the guidance given. 1 Purpose and Scope This COP describes the procedure to be used when hand laying cables. The instructions in this document

More information

Project Management Institute. The Standard for Program Management

Project Management Institute. The Standard for Program Management Project Management Institute The Standard for Program Management The Standard for Program Management ISBN: 1-930699-54-9 Published by: Project Management Institute, Inc. Four Campus Boulevard Newtown Square,

More information

3M Electromagnetic Compatible Products

3M Electromagnetic Compatible Products 3M Electromagnetic Compatible Products Selection Guide Revision E 3 Innovation Faster, smaller, lighter, easier the skyrocketing development of today s electronics requires new solutions for significant

More information

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for Underground Enclosure Integrity

ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE Specification for Underground Enclosure Integrity ENGINEERING COMMITTEE Interface Practices Subcommittee AMERICAN NATIONAL STANDARD ANSI/SCTE 77 2010 Specification for Underground Enclosure Integrity NOTICE The Society of Cable Telecommunications Engineers

More information

PRODUCT SELECTION LOCATOR

PRODUCT SELECTION LOCATOR PRODUCT SELECTION LOCATOR SECTION SPECIFICATION 1 300V Instrumentation Cables 1000 2 600V Instrumentation Cables 2000 3 600V Flexible Control and Power Cables 3000 4 600V Multi Conductor Control and Power

More information

MESP TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 400mm 2 ALUMINIUM CONDUCTOR 1.9kV XLPE INSULATED WITH METALLIC SCREEN

MESP TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 400mm 2 ALUMINIUM CONDUCTOR 1.9kV XLPE INSULATED WITH METALLIC SCREEN Engineering Specification Electrical Networks TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 400mm 2 ALUMINIUM CONDUCTOR 1.9kV XLPE INSULATED Version: 1 Issued: March 2014 Owner: Electrical Networks Asset

More information

3M Ground Plane Cable.050" 28 AWG Stranded, One Drain, PVC 3476 Series

3M Ground Plane Cable.050 28 AWG Stranded, One Drain, PVC 3476 Series M Ground Plane Cable.050" 28 AWG Stranded, One Drain, PVC 476 Series 28 AWG wire on.050 inch centers permits mass termination to a broad line of IDC connectors Ground plane construction for increased signal

More information

BASIC CONCEPTS IN ELECTRICAL DESIGN. Prepared by Engr. John Paul Timola

BASIC CONCEPTS IN ELECTRICAL DESIGN. Prepared by Engr. John Paul Timola BASIC CONCEPTS IN ELECTRICAL DESIGN Prepared by Engr. John Paul Timola ELECTRICAL CONDUCTORS AND INSULATORS Electrical Conductors substances that offer a very low resistance to current flow. Insulators

More information

MESP TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 70mm 2 FLEXIBLE TINNED COPPER CONDUCTOR 3.3kV EPR INSULATED WITHOUT METALLIC SCREEN

MESP TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 70mm 2 FLEXIBLE TINNED COPPER CONDUCTOR 3.3kV EPR INSULATED WITHOUT METALLIC SCREEN Engineering Specification Electrical Networks MESP 030000-04 TECHNICAL SPECIFICATION FOR ELECTRIC CABLE 70mm 2 FLEXIBLE TINNED COPPER CONDUCTOR 3.3kV EPR INSULATED WITHOUT METALLIC SCREEN Version: 1 Issued:

More information

Article 300: Wiring Methods And Materials

Article 300: Wiring Methods And Materials Part E: Code Book Questions Article 300: Wiring Methods And Materials 1.! Conductors of A.C. or D.C. circuits rated 600 volt or less, shall be permitted to occupy the same! conduit if.! (a)!conductors

More information

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 21138-3 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)

More information

ENGLISH. 1metre 7/.02mm Teflon insulated twin twisted lead

ENGLISH. 1metre 7/.02mm Teflon insulated twin twisted lead Datasheet Platinum Resistance Pt100 Sheathed Thin Film Strip Sensor 2 wire sensor sheathed in a thin stainless steel shim body ideal for surface measurement ENGLISH Sheathed Pt100 element in a thin, flat

More information

catalog Copper Wires

catalog Copper Wires catalog Copper Wires ASWire Aerial Service Wire Self Supporting Multi-pair Pair Count 1-18P Multi-pair, self-supporting Aerial Service Wires (ASW) are used for subscriber lines in exchange plant; single-pair

More information

Product Information. Stress Control Element Insulation. 3M QS 2000E 24kV I DN A

Product Information. Stress Control Element Insulation. 3M QS 2000E 24kV I DN A Volume: Power Utility Section: Medium-Voltage Power Cables 6/10 (12) kv up to 21/36 (42) kv Product: 3M QS 2000E Number/Issue: AABBCC46047#E/01 Date: February, 13.2007 Author: W. Röhling / R. Hornig 1.

More information

ITEM L-119 AIRPORT OBSTRUCTION LIGHTS DESCRIPTION

ITEM L-119 AIRPORT OBSTRUCTION LIGHTS DESCRIPTION SECTION 74 AIRPORT OBSTRUCTION LIGHTS (FAA L-119) 74-1 GENERAL The Contractor shall perform all work required by the plans and specifications for construction of obstruction lights in accordance with the

More information

Product Selection Guide. Color & Additives - Europe. Color & Additives. Concentrates for the Wire & Cable Industry

Product Selection Guide. Color & Additives - Europe. Color & Additives. Concentrates for the Wire & Cable Industry Product Selection Guide Color & Additives - Europe Color & Additives Concentrates for the Wire & Cable Industry OnColor Color Concentrates for Wire & Cable Europe PolyOne provides 13 product series covering

More information

Sika KAB combination joint waterbars waterstopping systems

Sika KAB combination joint waterbars waterstopping systems PRODUCT DATA SHEET Sika KAB combination joint waterbars Waterbars for waterproofing construction and crack induced shrinkage joints in new reinforced concrete structures PRODUCT- DESCRIPTION KAB 125/KAB

More information

SPECIFICATION RW-2514 Document Number NBC MARKER SYSTEM (Ladder Form) NBC-SCE

SPECIFICATION RW-2514 Document Number NBC MARKER SYSTEM (Ladder Form) NBC-SCE SPECIFICATION: RW 2514 THIS ISSUE: ISSUE 2 DATE: February 2014 SPECIFICATION RW-2514 Document Number 108-121017 NBC MARKER SYSTEM (Ladder Form) NBC-SCE 1. SCOPE NBC-SCE Markers are designed for use where

More information

SECTION 16496A MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number

SECTION 16496A MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number PART 1 GENERAL 01 02 03 04 SCOPE Furnish and install Manual Transfer Switches (MTS) and

More information

2OO9-2O1O HITACHI TECHNOLOGY. Materials, Components & Others

2OO9-2O1O HITACHI TECHNOLOGY. Materials, Components & Others 2OO9-2O1O HITACHI TECHNOLOGY Materials, Components & Others 69 HIGHLIGHTS 2OO9-2O1O Commencement of Trials of Gas Turbine Blades Made of Nickel-based ngle-crystal Alloy to Improve Thermal Efficiency of

More information

DESIGN STANDARD WIRE DERATING

DESIGN STANDARD WIRE DERATING DESIGN STANDARD WIRE DERATING Sept 3, 2008 Japan Aerospace Exploration Agency This is an English translation of JREG-2-212. Whenever there is anything ambiguous in this document, the original document

More information

Design, Testing and Utilization of Welded-Wire Rack Decking

Design, Testing and Utilization of Welded-Wire Rack Decking MH 26.2-2007 (revision of MH26.2 2004) Design, Testing and Utilization of Welded-Wire Rack Decking Material Handling Industry of America A Division of Material Handling Industry 8720 Red Oak Blvd., Suite

More information

CERTIFICATIONS AND LISTINGS

CERTIFICATIONS AND LISTINGS CERTIFICATIONS AND LISTINGS REHAU PEXa Tubing, Effective October 2017 TABLE OF CONTENTS Table 1: REHAU Certifications and Listings 1. REHAU PEX Tubing..................................4 2. Fire-rated Assembly

More information

2 Pfg 1169/ Requirements for cables for use in photovoltaic-systems

2 Pfg 1169/ Requirements for cables for use in photovoltaic-systems 2 Pfg 1169/08.2007 Requirements for cables for use in photovoltaic-systems Jede Art der Vervielfältigung, auch auszugsweise, nur mit Genehmigung Seite 1 von 23 Contents Seite Foreword...3 1 Scope...3 2

More information

VERSAFIT V2 AND V4 TUBING Polyolefin, Flexible, Heat-Shrinkable, Flame-Retardant

VERSAFIT V2 AND V4 TUBING Polyolefin, Flexible, Heat-Shrinkable, Flame-Retardant TE Connectivity 300 Constitution Drive Menlo Park, CA 94025 USA Raychem Tubing Specification This Issue: Date: Replaces: RW-3023 Issue 9 Nov 21, 2016 Issue 8 VERSAFIT V2 AND V4 TUBING Polyolefin, Flexible,

More information

P.V.C. INSULATED UNARMOURED COPPER CABLES

P.V.C. INSULATED UNARMOURED COPPER CABLES 083 : 2007 CEB SPECIFICATION P.V.C. INSULATED UNARMOURED COPPER CABLES CEYLON ELECTRICITY BOARD SRI LANKA Specification for P.V.C. INSULATED UNARMOURED COPPER CABLES CEB Specification 083 : 2007 CEYLON

More information