SECONDARY CONTAINMENT COATING SPECIFICATION
|
|
- Jared Booth
- 6 years ago
- Views:
Transcription
1 SECONDARY CONTAINMENT COATING SPECIFICATION 1.0 GENERAL PROVISIONS Applicable to the following areas: Typical concrete secondary containment structure with occasional exposure acidic and alkaline compounds as indicated in Spirit 100 Line (attached) and Spirit 200 Line (attached). Product is suitable for 72-hour secondary containment purposes for these chemicals. The product will not be resistant to prolonged contact with concentrated nitric acid (greater than 10%) for periods of 72 hours. Discoloration of the product may occur with contact to some of the chemicals, but this is not necessarily indicative of film integrity. Prolonged contact with concentrated acids, oxidizers, or will result in degradation of the film. The product will provide chemical resistance that is generally the same as the Flakeline 2000 product currently installed. Specific application instructions Please refer to attached product data sheets for specific application instructions including mixing instructions, curing times, and environmental limitations.
2 2.0 SURFACE PREPARATION General Surface Preparation Detect and remove areas of disbonding, deteriorated, or otherwise faulty lining until the lining exhibits good adhesion with no chemical degredation of the lining or underlying concrete. Using a power grinder (angle grinder with abrasive disc or other), taper abrade the tightly adhering lining at the perimeter of the repair area 2-5 inches from the substrate. Power wash the entire containment area to remove chemical contaminants. A hot water wash is highly recommended. Follow the initial wash by cleaning with a Prep 88 solution diluted at 3 parts clean water to 1 part concentrate. Briefly scrub as needed using a nylon brush with long handle to work into any surface residues. Within minutes, power wash the floor to thoroughly remove the Prep 88 cleaner. Do not allow Prep 88 to dry on the floor. Power wash directly into concrete areas where the previously lining had failed. Ensure the surface ph is neutral ( ) and completely dry prior to continuing. Surface Preparation overcoating existing lining See general surface preparation steps. Uniformly and thoroughly abrade the existing to using power sanding (floor sander/ orbital sanders) with 80-grit sandpaper to ensure a uniform and complete discoloration / de-glossing of the coating. Alternately, sweep blast with a medium fine grit to abrade the surface. Using a grinder, roughen the surface of polymer concrete repair surfaces (after sufficient curing) to obtain a surface roughness of 60 grit or coarser. Vacuum surfaces to completely remove particulate residue. Lightly solvent wipe with
3 Amercoat 12 cleaner prior to coating application. Spot prime polymer concrete surfaces with Amerlock Sealer. Surface Preparation concrete / deteriorated lining patch See general surface preparation steps. Concrete should be free of any chemical contamination, oils, grease, etc Prepare concrete by power tool grinding to achieve a uniform surface roughness equivalent to 60-grit sandpaper or coarser and in accordance with ICRA Replica Standards CSP 3-5. Surface should be sound with no exposed aggregate, free of sub-surface voids, and dust free. Surface should be dust free at the time of coating application. Blow down or vacuum as necessary to achieve. Joints should be abrasive blasted and subsequently blown with compressed air to remove all loose particulate. Surface Preparation exposed steel See general surface preparation steps. Abrasive blast using an angular abrasive to achieve an SSPC SP-10 condition with a mil anchor profile. Prime pitted steel with Amerlock Sealer. Fill pits as needed with Amercoat 114A epoxy filler.
4 3.0 COATING APPLICATION Polymer Concrete Repair / re-form deteriorated / broken concrete surfaces using an epoxy concrete repair compound such as Polyspec Res Rok 157 or equivalent. Apply in accordance with manufacturer s instructions. Primer Amerlock Sealer should be applied to severely pitted steel, exposed concrete, and prepared polymer concrete surfaces. Apply 1 coat of Amerlock Sealer at approximately 1-2 mils to wick into the concrete / pitted steel. Overlap the previously abraded / tapered lining at the perimeter of the repair area. Amerlock Sealer may be applied via roller or airless spray equipment. Reinforced Lining Patch Pre-cut 1.5 ounce fiberglass mat to fit the repair area. Pour and roll (or spray larger areas) Novaguard 840 at mils wet film thickness. After 30 minutes, lay in the glass mat working in one direction. Back roll using a short nap or napless roller to work the mat into the epoxy.
5 Joint Treatment (where applicable) Install either an acid resistant elastomeric backer rod or (preferably) a pre-formed FRP joint all functional floor joints. Apply PPG Rapid Seal 650 polysulfide joint sealant or equivalent to seal all floor joints. Sealant should be applied flush with the coated floor surface. When set, apply bond breaker tape to the full width of the joint. Over-coating System Inspect the repair patch areas and sand to remove any bubbling if required. With 7 days of the Amerlock Sealer application, apply 1 coat of Novaguard 840 at mils to all surfaces. Novaguard 840 is to be applied directly to the prepared surfaces of the existing lining. Novaguard 840 is applied with standard 64:1 ratio airless spray equipment. 4.0 FINAL CURING Allow system to cure with good ventilation (approximately 6 air turnovers per hour) for the following schedule prior to sustained chemical contact: 50 o F 60 o F 70 o F 80 o F 14 days 10 days 7 days 5 days
SECTION JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS
SECTION 07-9200 - JOINT SEALANTS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSURFACE PREPARATION INSTRUCTIONS: CONCRETE
SURFACE PREPARATION INSTRUCTIONS: CONCRETE DEFINITION OF TERMS The terms listed will be used frequently throughout this article and listed in boldface for ease of reference. They describe, in detail, the
More informationDURASHIELD 310 &
DURASHIELD 310 & 310-61 I. Scope A. This specification defines application requirements of DuraShield 310 & DuraShield 310-61 plural-component 100% solids, 3:1 volumetric mix ratio polyurethane to concrete,
More informationTL-280 Sprayable Flake Glass Vinyl Ester Lining System
TL-280 Sprayable Flake Glass Vinyl Ester Lining System PRODUCT DESCRIPTION TL-280 is a high performance, flake glass vinyl ester lining system, utilizing carefully selected and sized glass flake reinforcement
More informationThere are many surface contaminants that can interfere with coating adhesion. The following are the most common:
ATB-103 General Coating Preparation Guidelines Introduction In real estate, the key phrase is Location! Location! Location! With paints and coatings, the phrase is Preparation! Preparation! Preparation!
More informationSemstone Construction Details
Semstone Construction Details SP01-94 Treatment for Expansion Joints, Control Joints, and Structural Cracks, Vertical and Horizontal, for Non-Vehicular Traffic 1. Maintain joint/crack through coating.
More informationCarboguard 890 PRODUCT DATA SHEET SELECTION & SPECIFICATION DATA. Generic Type. Cycloaliphatic Amine Epoxy
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Cycloaliphatic Amine Epoxy Highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial
More informationSECTION EPOXY TERRAZZO
SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to
More informationCONCRETE STEPS, HANDRAILS, AND SAFETY RAIL
SUDAS Standard Specifications Division 9 - Site Work and Landscaping Section 9080 - Concrete Steps, Handrails, and Safety Rail CONCRETE STEPS, HANDRAILS, AND SAFETY RAIL PART - GENERAL.0 SECTION INCLUDES
More informationGeneral Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions.
General Applications Before applying, mix the pre-measured catalyst* into Liquid Roof by following label directions. Surface Preparation: Surface to be coated should be clean, dry and structurally sound.
More informationFLUID APPLIED WATERPROOFING
SECTION 07120 FLUID APPLIED WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-In-Place Concrete. 2. 09200 - Metal Studs, Metal Lath, Suspension Ceilings, Plaster, and Stucco.
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss >4% <70% 83mg IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor P is a suitable screed that can be applied on cement-based floors which need high mechanical
More informationREBOUND ACE AIR CUSHION
This procedure is applicable to Rebound Ace Air Cushion using Rebound Air Cushion Mat NG- 7mm. PREPARATION Thoroughly clean or vacuum court surface before application, remove any dirt, stones, dust. Surface
More informationInstruction Guide APPLICATION OF CIM TO CONCRETE
23 Elm St., Peterborough, NH 03458 Tel: (800) 543-3458 (603) 924-9481 Fax: (603) 924-9482 Web site: Instruction Guide APPLICATION OF CIM TO CONCRETE 1.0 DESCRIPTION This guide covers the installation of
More informationApplication Guide AC- 130 Metal Alloy Surface Preparation For Bonding
Application Guide AC- 130 Metal Alloy Surface Preparation For Bonding SCOPE This document describes the process for the application of AC- 130 pre-bond surface treatment to facilitate adhesive bonding
More informationPart of the Sikaplan WT Membrane System
System Product Data Sheet Edition: 10.2011 Identification no: 02 07 03 02 System Sikaplan WT Tape 200 System Part of the Sikaplan WT Membrane System Product Description Sikaplan WT Tape 200 is a high performance
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists
More informationPAYING ATTENTION TO DETAIL by Bob Cusumano
PAYING ATTENTION TO DETAIL by Bob Cusumano Painting contractors are often required to install caulk or sealant in exterior joints. Too often, the sealant is simply gunned into the joint until it s filled
More informationARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment
ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
More informationProduct Information CHEMGLAZE B 9942 A/B. Coating for Casting Pits. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces.
Product Information Chemical Products Division CHEMGLAZE B 9942 A/B Coating for Casting Pits. FEATURES BENEFITS. Easy Application Chemglaze B 9942 A/B will bond to damp and wet surfaces. Will build to
More informationVulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS
Vulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS 1. Purpose 1.1 The purpose of this document is to establish uniform procedures for applying the Vulkem Extreme Wearing System (EWS).
More informationA Design Review of Waterproofing Codes
A Design Review of Waterproofing Codes Section 1807 of Chapter 18 of the International Building Code addresses waterproofing under the section title of Dampproofing and Waterproofing. The section defines
More informationTECHNICAL DATA SHEET
Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and
More informationSECTION High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes)
- 1 - SECTION 099600 High Performance Coatings Field Applied Acrylic Urethanes (Solid Color, Pearl and Metallic Finishes) PART 1 GENERAL 1.1 SECTION INCLUDES A. Systems for field applied acrylic urethane
More information1. Rapid Set Cement. 2. Methods of preparation. 3. How to stage a job site. 4. Installation Mix, place, finish. 5. Coloring the TRU.
1. Rapid Set Cement 2. Methods of preparation 3. How to stage a job site 4. Installation Mix, place, finish 5. Coloring the TRU natural TRU Rapid Set is NOT Portland Cement Rapid Set is a Calcium Sulfoaluminate
More informationApplication Guidelines
Technical Bulletin MANUFACTURER Raven Lining Systems 13105 E. 61 st Street, Suite A Broken Arrow, OK 74012 (918) 615-0020 DESCRIPTION Application Guidelines DESCRIPTION Raven Lining Systems offers several
More informationPREPARATION IS THE KEY TO SUCCESSFUL FLOOR COATINGS By Bob Cusumano
PREPARATION IS THE KEY TO SUCCESSFUL FLOOR COATINGS By Bob Cusumano Coating new concrete floors can really be tough. Whether you re painting the floor of a large warehouse or the garage in a home, there
More informationAsh Brook Golf Course Scotch Plains, New Jersey
SECTION 033543 - POLISHED CONCRETE FINISHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationApplication Guide HI-TEMP 1027 APPLICATION GUIDE. Number: AG-3001 Revision: Page 1 of Introduction. 2. Where to apply Hi-Temp 1027
Page 1 of 7 This document provides information and details for the use and application of Hi-Temp 1027. It is designed to supplement the Hi-Temp 1027 Product Data sheet (PDS) and MSDS, not to replace them.
More informationInstallation Instructions
Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING
More informationAPPLICATION INSTRUCTIONS
Vulkem EWS with PUMA Technology (Heavy Duty) APPLICATION INSTRUCTIONS 1. Purpose 1.1 The purpose of this document is to establish uniform procedures for applying the Vulkem Extreme Wearing System (EWS)
More informationSoft Grip. WATERBASED Anti-Slip Coatings
Soft Grip WATERBASED Anti-Slip Coatings Soft Grip Coatings have been formulated for use on FIBERGLASS, CONCRETE, WOOD and PRIMED METAL surfaces. When used properly, these products provide a tough, anti-slip
More information***********************************************************************************
AQUAFIN-2K/M Two-Component Cement-based Acrylic-based Waterproofing GUIDE AQUAFIN, Inc. SPECIFICATION PART 1 - GENERAL 1.1 SECTION INCLUDES SECTION 07 16 14 ACRYLIC MODIFIED (FLEXIBLE) CEMENTITIOUS WATERPROOFING
More informationCONCRETE REPAIR IN ACTION: USING THE MANUAL AS A GUIDE. Christen Longoria, P.E. San Antonio District Project Engineer
CONCRETE REPAIR IN ACTION: USING THE MANUAL AS A GUIDE Christen Longoria, P.E. San Antonio District Project Engineer TxDOT CONCRETE REPAIR MANUAL Step-by-Step repair procedures for use on new and existing
More informationColphene BSW Training and Application Guide. Colphene BSW Waterproofing Membrane. 1. Prepare substrate
Colphene BSW Training and Application Guide Colphene BSW Waterproofing Membrane. 1. Prepare substrate Substrate must be structurally sound. Surface must be free of voids, spalled areas, loose aggregate,
More informationCopyright 2018, The Sherwin-Williams Company ISSUED MAY CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY
Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 67 00 CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL INTERIOR SPECIFICATION GUIDE This Painting Schedule
More informationA. This Section includes resinous flooring systems with epoxy body coat(s).
SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes resinous flooring systems with epoxy body coat(s). 1. Application Method: Troweled (Slurry, Seeded or Broadcast
More informationBroadcast Parking Garage System
AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete
More informationTECHNICAL DATA SHEET
Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.
More informationPRIMERS & SURFACE PREPARATION GUIDE
PRIMERS & SURFACE PREPARATION GUIDE Era Polymers Primers & Surface Preparation Guide 1 There are three responses when looking at a coated surface yes, no, and WOW! Wow is the one to aim for. Era Polymers
More informationCleaning and Protecting Concrete Surface Preparation, Application, and Inspection. NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc.
Cleaning and Protecting Concrete Surface Preparation, Application, and Inspection NESMEA October 17, 2017 Kenneth A. Trimber KTA-Tator, Inc. Cleaning and Protecting Concrete Surface Preparation, Application,
More informationLiquid applied polyurea hybrid membrane
Product Data Sheet Edition 07/08/2008 Identification no: 02 06 07 01 001 0 000015 Sikalastic -842 BG Liquid applied polyurea hybrid membrane Product Description Sikalastic -842 BG is a two part, highly
More informationConstruction. 3-part cement and epoxy combination micro mortar for surface sealing. Product Description 1 1/5. Tests
Product Data Sheet Edition 29/11/2007 Identification no: 02 03 02 01 002 0 000002 SikaGard -720 EpoCem ZA 3-part cement and epoxy combination micro mortar for surface sealing Construction Product Description
More informationKOSTER AMERICAN CORPORATION
Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General
More informationAcetone is flammable; refer to the manufacturer s instructions for complete safety information.
Installing UPP FRP Entry Seals on Fiberglass Sumps Introduction This document is meant as an installation overview for UPP FRP entry seals with fiberglass sumps and should be used in conjunction with the
More informationConcrete Floor Coating Challenges
48 D+D MARCH 2015 True Grit Concrete Floor Coating Challenges Dave Lick, Paint Quality Assurance Inspector Peeling paint reveals a coating system failure in a commercial hallway. Planning and preparation
More informationRust Bullet Home and Farm FAQ s
Rust Bullet Home and Farm FAQ s 1. Will Rust Bullet Protect My Galvanized Metal Roof? Yes. Rust Bullet is the ideal coating for protecting sheet metal buildings and roofs; it not only provides protection
More informationHYDRAULIC GATE SEALS. Industrial Rubber Supply (1995) Ltd.
Industrial Rubber Supply (1995) Ltd. Manufacturers of Quality Industrial Products 55 Dunlop Avenue, Winnipeg, Manitoba, Canada R2X 2V2 Phone (204) 694-4444 - Fax (204) 632-6767 - www.indrub.com ISO 9001:2000
More informationConstruction. High performance joint sealing system. Product Description. System Data Sheet Edition _1. 1 Sikadur Combiflex SG system 1/8
System Data Sheet Edition 2012-05_1 High performance joint sealing system Construction Product Description Uses High performance joint sealing system for construction, expansion and connection joints as
More informationBEP Blue Barrier Installation and Application Guide
BEP Blue Barrier Installation and Application Guide BEP Blue Barrier is a system of seamless fluid applied products designed to protect the building envelope. Approved assemblies and applications listed
More informationSURFACE PREPARATION FOR SYNTHETIC ROPES
Published date: June 30, 2005 SURFACE PREPARATION FOR SYNTHETIC ROPES Rust damaged chock typical of crude tankers. The following recommendations can be applied at the shipyard or during vessel operations.
More informationSikafloor -161 is an economic, two part, solvent free, low viscosity epoxy resin, suitable for use under hot climate condition.
Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -161 2-part epoxy primer, levelling mortar, intermediate layer and mortar screed Construction Product Description Sikafloor -161
More informationApplication Guidelines
Application Guidelines 1.0 SCOPE This document contains general instructions and recommended practices for the application of the SERVIWRAP cold applied tape coating system. The various coating grades
More informationTwo component solvent-free epoxy system for creation of self-levelling floors. Gloss <4% <70% IR4
Two component solvent-free epoxy system for creation of self-levelling floors Fields of Application Epoxol Floor S is a suitable screed that can be applied on cement-based floors which need high mechanical
More informationPRODUCT GUIDE: ZINC-RICH COATINGS. Version:
PRODUCT GUIDE: ZINC-RICH COATINGS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy,
More informationPOLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES
POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES A large percent of corrosion failures on cathodically protected structures are associated
More informationSECTION RESILIENT SHEET FLOORING
SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.
More informationSECTION mil thickness COLD FLUID-APPLIED WATERPROOFING
SECTION 07 14 16 CCW-MIRASEAL @ 120 mil thickness COLD FLUID-APPLIED WATERPROOFING PART 1 - GENERAL 1.1 SECTION INCLUDES: Installation of waterproofing membrane on surfaces indicated on drawings, consisting
More informationSurface Preparation. The simple reason surface preparation exists is to help coatings stick better. It does this in three ways
Section Name Last Updated 11/14 Aim Scope References Surface Preparation This is obviously a very broad question that could fill a text book when answered fully. The aim of this document is to cut through
More informationWATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions
WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION Responsibility for the suitability of this flooring
More informationConstruction. Sikadur -Combiflex SG System High performance joint sealing system. Positioning. Product Data
Product Data Sheet Version Nos.: 04/13 (replaces 02/13) Only to be applied by a Sika Approved Contractor Sikadur -Combiflex SG System High performance joint sealing system Construction Positioning Description
More informationData Sheet 1806 Englisch
Data Sheet 1806 Englisch Silicate Interior Paint ELF 1806 Silikat-Innenfarbe ELF 1806 low emission, solvent and plasticizer free, dull matt, wet abrasion resistance class 3, suitable for allergy sufferers,
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroBuild PT/ HT Epoxy Mortar ¼ Power Trowel or Hand Trowel Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer
More informationMETHOD STATEMENT 001 CONCRETE BALCONY WATERPROOFING FOR DIRECT FIXED TILES
This Document is designed to cover best practice installation methods for the installation of a class 2/3 waterproof membrane system to external concrete balconies in accordance with AS 4654.2 PRELIMINARY
More informationTechnical Service. INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products. This document refers to the following products:
INSTALLATION INSTRUCTIONS FOR TARAFLEX SPORT PRODUCTS over Gypsum base Products This document refers to the following products: Product Width Width Ft. Installation direction Seams treatment Taraflex Surface
More informationNormadur 65 HS. Technical Data PROPERTIES AND RECOMMENDED USAGE TECHNICAL DATA
Technical Data Normadur 65 HS PROPERTIES AND RECOMMENDED USAGE Paint type: NORMADUR 65 HS is a fast drying, flexible polyurethane coating with an aliphatic isocyanate curing agent. NORMADUR 65 HS is high-solid
More informationProfessional Floor Restoration & Rejuvenation MADE EASY
By Malish Professional Floor Restoration & Rejuvenation MADE EASY Your Global Source For Engineered Brushes Since 1948 Diamabrush By Malish Floor Restoration System The Diamabrush By Malish Floor Restoration
More informationPolymer Linings for Restoration & Corrosion Protection of Steel Surfaces: Crude Oil Storage Tank Repair and Reline in New Zealand
Polymer Linings for Restoration & Corrosion Protection of Steel Surfaces: Crude Oil Storage Tank Repair and Reline in New Zealand ~ 2009 SSPC Corrosion Conference ~ By: Greg Severyn, Sauereisen Inc., Greg
More informationThe Application Guide offers product details and recommended practices for the use of the product.
Technical Data Sheet Application Guide Approved 720 1,2 720 silicone acrylic ^(ValidationDate) 1 Product description This is a one component physically drying silicone acrylic coating. It is heat resistant
More informationARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface
ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and
More informationRust-Oleum Industrial Brands Specification
Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 2 A solvent based coating system High Performance 9100/9800 System DTM Epoxy Mastic/DTM
More informationSECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING
SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,
More informationRUST TRAP TM TECHNICAL DATA SHEET
RUST TRAP TM TECHNICAL DATA SHEET Check local VOC DESCRIPTION Rust Trap is a moisture cross- linked urethane for coating ferrous metals. Rust Trap also adheres to aluminum, fiberglass and properly prepped
More informationNXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N
NXT SUBSTRATE PREPARATION AND PRIMER GUIDE TDS 230N Substrate preparation is the most important factor to successful NXT self-leveling underlayment (SLU) and NXT Vapor Reduction Coating installations.
More informationSolvent Based Clear PU Sealer
PROFESSIONAL USE ONLY Solvent Based Clear PU Sealer Description EpiMax 900 Solvent Based Clear PU Sealer is a hard, stain resistant, non-yellowing, cross-linking protective sealer for concrete floor surfaces
More informationADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM
ADA APPROVED SURFACE APPLIED DETECTABLE WARNING SYSTEM PART 1 GENERAL 1. RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions, apply to this Section.
More informationSPRAY-APPLIED HYBRID POLYUREA OR PURE POLYUREA-BASED WATERPROOFING SYSTEM FOR TRAFFICKED ROOFS AND BRIDGES AND VIADUCT DECKS
Purtop System Deck SPRAY-APPLIED HYBRID POLYUREA OR PURE POLYUREA-BASED WATERPROOFING SYSTEM FOR TRAFFICKED ROOFS AND BRIDGES AND VIADUCT DECKS PRODUCTS USED FOR THE SYSTEM: Purtop 400 M - Purtop 1000
More informationBEP Blue Barrier Installation and Application Guide
BEP Blue Barrier Installation and Application Guide BEP Blue Barrier is a system of seamless fluid applied products designed to protect the building envelope. Approved assemblies and applications listed
More informationMaximum Rust Protection!
ZERO-RUST Zero Rust is a direct-to-metal, phenolic modified alkyd rust and corrosion control coating, which controls rust and corrosion by putting down an impermeable barrier at the steel level. Its dielectric
More informationE L A S T O - S H I E L D P R E P A R A T I O N & A P P L I C A T I O N
E L A S T O - S H I E L D S U R F A C E P R E P A R A T I O N & A P P L I C A T I O N G U I D E P e r f o r m a n c e n e v e r l o o k e d b e t t e r. T A B L E O F C O N T E N T S Typical Systems 1
More informationARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound
ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE
More information1.02 DESCRIPTION A. This Section specifies furnishing and installing Surface Applied Detectable/Tactile Warning Surface Tiles where indicated.
SURFACE APPLIED DETECTABLE/TACTILE WARNING SURFACE TILE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Special Conditions and Division 1 Specifications
More informationITEM 458 WATERPROOFING FOR STRUCTURES
ITEM 458 WATERPROOFING FOR STRUCTURES 458.1. Description. This Item shall govern for the furnishing and placing of waterproofing on concrete and steel bridge decks of railroad structures and on other structures
More informationEngineering Branch Assets Delivery Group
F.1 SCOPE This Technical Specification shall apply to Fibre Reinforced Plastics or Glass Reinforced Plastics (hereinafter referred to as FRP or GRP) structures and the materials used in their manufacture,
More informationSpecifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.
This resinous flooring specification consists of a flexible hybrid polymer primer and basecoat, urethane concrete slurry resurfacer, and double broadcast decorative vinyl flake system based on aliphatic
More informationRefer to Substrates & Surface Preparation.
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic Polyurethane Thin film, high gloss finish with exceptional weathering performance
More informationINSTALLATION AND MAINTENANCE MANUAL
Athletic Vinyl Padded Roll AND MAINTENANCE MANUAL Greatmats.com 117 Industrial Ave Milltown, WI 54858 P: 877-822-6622 F: 715-825-4928 info@greatmats.com TABLE OF CONTENTS Job Site Conditions 3 Subfloors
More informationA. Section includes surface preparation and the application of high-performance coating systems on the following substrates:
ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY
More information1.4 kg/l (11.4 lb/us gal) Maximum 272 g/kg (Directive 1999/13/EC, SED) Maximum 420 g/l (3.5 lb/gal) To 650 C (1200 F) To 538 C (1000 F)
DESCRIPTION One component heat resistant silicone topcoat for use in an elevated temperature coating system, primarily for application over PPG HI-TEMP 1027 primer PRINCIPAL CHARACTERISTICS Heat resistant
More informationALSAN RS POCKET INSTRUCTIONS
ALSAN RS POCKET INSTRUCTIONS ALSAN RS Pocket Guide INDEX SECTIONS PAGE Surface preparation 07 Product information Systems information Application information Details 9 ALSAN RS Pocket Guide TIME TESTED
More informationSuggested Specification for Tri-Patch Versatile Concrete Patching Compound
Suggested Specification for Tri-Patch Versatile Concrete Patching Compound SURFACE PREPARATION for Interior and Exterior Floor-Covering Installations. (Vinyl Composition Tiles, Sheet Vinyl, Rubber, Indoor
More informationConstruction. High performance joint sealing system. Product Description 1 1/9. Product Data Sheet Edition 29th October 2015
Construction Product Data Sheet Edition 29th October 2015 Sikadur-Combiflex SG system High performance joint sealing system Product Description The Sikadur-Combiflex SG system is a high performance joint
More informationVapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring
advanced moisture control, inc. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring 250 polished concrete slabs! Made in Southern California,
More informationAPPLICATION GUIDELINES RAPID REPAIR EXTERIOR DECK SYSTEM
APPLICATION GUIDELINES RAPID REPAIR EXTERIOR DECK SYSTEM Revision 6 Issue Date: 15 th September 2015 Registered Office The AkzoNobel Building, Wexham Road, Slough, SL2 5DS Page 1 CONTENTS Page 1. SCOPE
More informationPOLYMER CONCRETE 100 EPOXY POLYMER CONCRETE DILUTE ACIDS RESISTANCE
RECOMMENDED APPLICATIONS Polymer Concrete 100 is a three-component, epoxy polymer concrete used for the construction of chemical resistant floors, pads, curbing, trenches and sumps. Polymer Concrete 100
More informationBENTLEY ELEMENTS COLLECTION LVT
This document refers to the following products: Product Size Thickness Installation direction Seams treatment Elements Square See specifications 2.5mm 90 None Elements Plank See specifications 2.5mm Stair
More informationAliphatic Acrylic-Polyester Polyurethane
SELECTION & SPECIFICATION DATA Generic Type Description Features Color Finish Primer Dry Film Thickness Aliphatic Acrylic-Polyester Polyurethane High build, low sheen finish that has excellent resistance
More informationCorlar 2.1 PR-P High Solids Productive Epoxy Primer
Corlar 2.1 PR-P High Solids Productive Epoxy Primer GENERAL DESCRIPTION A high solids, two component, VOC conforming (2.1 lbs./gal.) Low HAPS productive primer based on Axalta modified polyamide epoxy
More informationStanford University Facilities Design Guidelines SECTION SEAL COATS. C. Section : Traffic Striping and Pavement Markings
SECTION 32 12 36 SEAL COATS PART 1 GENERAL 1.1 RELATED WORK A. Section 31 10 00: Site Preparation B. Section 32 12 00: Flexible Paving C. Section 32 17 23 01: Traffic Striping and Pavement Markings 1.2
More informationFlorock Seamless Flooring Systems
Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing
More information