Hammer-Capsule CHEMICAL PRODUCT DESCRIPTION SUGGESTED SPECIFICATION APPROVALS AND LISTINGS HAMMER CAPSULE SPECIFICATIONS

Size: px
Start display at page:

Download "Hammer-Capsule CHEMICAL PRODUCT DESCRIPTION SUGGESTED SPECIFICATION APPROVALS AND LISTINGS HAMMER CAPSULE SPECIFICATIONS"

Transcription

1 22 INSTALLATION OF ANCHORS OVERHEAD Prior to installing adhesive anchors overhead or in walls, consult with the governing building authority to determine the requirements for fire safety guidelines. The effect of elevated temperature on the Chem-Stud adhesive is shown on in the Adhesive Properties section. Chem-Stud capsules can be used for the installation of threaded anchor rod overhead. The anchor holes should be prepared following the standard installation procedures with the following exceptions. After the anchor hole is drilled and cleaned, insert the proper size capsule into the hole. For the 3" to sizes, select the proper size anchor seal plug and insert it into the hole until the rim of the plug is fully seated against the base material. Be sure the hole is deep enough to accept both the capsule and the plug. Following the standard procedures, insert the chisel-pointed anchor rod through the cross cut opening of the anchor seal plug and spin the rod into the capsule. An alternate method is to use a piece of duct tape or similar material to hold the capsule in place prior to spinning the anchor rod into the hole. If duct tape is used, it will be necessary to secure the chisel-pointed anchor rod in place until the adhesive gels. SUGGESTED SPECIFICATION The adhesive used shall be a two part capsule type system containing an epoxy acrylate resin (vinyl ester). The outer capsule shall contain the resin in which quartz aggregate shall be suspended and the inner capsule shall contain a dibenzoyl peroxide hardener. The capsule used shall have a minimum shelf life of two years. Anchor holes shall be drilled with a bit meeting the requirements of ANSI Standard B and shall be approved by the manufacturer. The adhesive capsule and anchor hardware components shall be installed according to the manufacturers instructions. Anchor rods (or inserts) shall be manufactured from steel and shall have a chisel point to properly mix the capsule. Chem-Stud capsules and the hardware used (except for reinforcing bar) shall be supplied by Powers Fasteners Inc. Hammer-Capsule BASE MATERIAL Solid Concrete SIZE RANGE 3" to Anchor Rod, No. 3 to No. 8 Reinforcing Bar ANCHOR MATERIAL Ester Based Resin PRODUCT DESCRIPTION The Hammer-Capsule System consists of a self contained, single use, two-part glass capsule into which threaded anchor rod or reinforcing bars can be directly driven without the need for a chisel point or spinning action. It is designed for use in the installation of 3" through diameter threaded rod in solid concrete and masonry materials. It can also be used to install reinforcing bars. A mixture of hardener and quartz aggregate is contained in the upper portion of the capsule while the lower portion contains an epoxy acrylate resin. Unlike traditional capsule anchors which required the use of chisel-pointed anchor rod and special installation tools, the Hammer-Capsule is designed for use with straight cut anchor rod. Straight Cut Rod APPROVALS AND LISTINGS The following approvals and listings are for reference purposes. They should be reviewed by the design professional responsible for the product installation to verify approved base materials, sizes, and compliance with local codes. ICBO ES Evaluation Report No SBCCI Report No The unique design reduces installation costs when compared with systems requiring chisel pointed rod and special installation tools. HAMMER CAPSULE SPECIFICATIONS The following table lists the shelf life and storage recommendations for the capsule. The properties listed apply to the cured Hammer-Capsule adhesive mortar. Shelf Life 2 years Storage Conditions Store dry at 4 to 9 F. Condition to 6 F. before use. Color Mixed adhesive mortar - amber Consistency Paste mortar

2 23 The mortar volume listed in the following table is for the mixed material. The diameter and length may be different than products offered by other manufacturer s capsules because of variations in air content. When comparing capsules, use the installed mortar volume. CAT. CAPSULE CAPSULE CAPSULE MORTAR MORTAR NO. SIZE DIAM. LENGTH VOLUME VOLUME 672 3".43" 3.5".4 in 3.22 fl. oz ".7 in 3.39 fl. oz ".67" 5." 1.4 in 3.77 fl. oz ".78" 5.5" 2.5 in fl. oz ".87" 6.89" 3.25 in fl. oz " 8.25" 4.5 in fl. oz. HAMMER-CAPSULE RECOMMENDED SETTING TIME The setting times for the Hammer-Capsule adhesive mortar are listed below. The setting time is the minimum time required for the mortar to reach its published physical properties. The setting times listed are for the base material temperature, not ambient air temperature. For example, when making installations inside a building in exterior walls during the winter, the temperature of the hole may be different than the interior temperature and should be measured to determine the setting time required. In order to ensure proper mixing, the capsule should be conditioned to a minimum temperature of 6 F. prior to use. BASE MATERIAL TEMPERATURE SETTING TIME 68 F. & over 1 hour 5 F. to 68 F. 2 hours 32 F. to 5 F. 5 hours 23 F. to 32 F. 1 hours 14 F. to 23 F. 24 hours Cure time should be doubled for wet concrete HAMMER-CAPSULE SELECTION GUIDE CAT. *DRILL MIN. STD. STD. WT./ NO. SIZE DIA. DEPTH BOX CTN " 7/16" /16" " 11/16" 5" " 7" 6" " 7" * The drill bit diameters and depths listed are for installations using threaded rod. Refer to the load tables for hole size to be used with reinforcing bars. HAMMER-CAPSULE ADHESIVE PROPERTIES RESISTANCE TO S The resistance of the cured Hammer-Capsule adhesive to various chemicals was determined according to ASTM Specification C 581 by laying molded samples of the resin in the respective chemical agents. The samples were subjected to a bending strength test before and after a 12 month exposure to the chemicals. The adhesive was rated as resistant if there was no visible deterioration and less than 25% reduction in bending strength. This exposure is extreme. Under normal installation conditions, the epoxy is exposed to the chemical agents only at the surface of the concrete around the top of the anchor hole. AGENT CONCENTRATION RESISTANT NOT RESISTANT Accumulator acid Acetic acid 4 Acetic acid 1 Acetone 1 Ammonia, aqueous solution 5 Aniline 1 Beer Benzene (kp 1-14 C) 1 Benzole 1 Boric acid, aqueous solution Calcium carbonate, suspended in water All Calcium chloride, suspended in water Calcium hydroxide, suspended in water Carbon tetrachloride 1 Caustic soda solution 1 Citric acid All Diesel oil 1 Ethyl alcohol, aqueous solution 5 Formic acid 1 Formaldehyde, aqueous solution Freon Fuel oil Glycol (Ethylene glycol) Hydrochloric acid Conc. Hydrogen peroxide 3 Isopropyl alcohol 1 Lactic acid All Linseed oil 1 Lubricating oil 11 Magnesium chloride, aqueous solution All Methanol 1 Motor oil (SAE 2 W-5) 1 Nitric acid 3 Nitric acid 1 Oleic acid 1 Perchloroethylene 1 Petroleum 1 Phenol, aqueous solution 8 Phosphoric acid 85 Potash lye (potassium hydroxide solution) 1 Potassium carbonate, aqueous solution all Potassium chlorite, aqueous solution all Potassium nitrate aqueous solution all Premium gasoline 1 Sodium carbonate, aqueous solution all Sodium chloride, aqueous solution all Sodium phosphate, aqueous solution all Sodium silicate all Standard benzine 1 Sulfuric acid 1 Sulfuric acid 7 Tartaric acid all Tetrachloroethylene 1 Toluene Trichloroethylene 1 Turpentine 1

3 24 EFFECT OF ELEVATED TEMPERATURE INSTALLATION PROCEDURES As with all adhesive anchors, the bond strength of the Hammer-Capsule is Drill a hole using a carbide tipped bit meeting affected by elevated temperatures in the base material. As the ;;;; yyyy of the diameter requirements of ANSI B to the base material increases, the bond strength of the anchor will decrease. Typical performance of the Hammer-Capsule adhesive at elevated base material the minimum depth required as shown in the temperatures is shown below. The values are based on maintaining the ;;;; yyyy concrete test samples used at a given temperature for a minimum of 24 hours before applying a test ;;;; yyyy 1 Starting from the bottom or back of the anchor hole, blow clean with compressed 9 air, brush the hole with a nylon brush, and blow it clean again. They may be dry or 8 damp, but should be free of standing water or frost. If using reinforcing bar, be 7 sure the bar will fit into the drilled hole. If a larger hole is required, the diameter 6 should be as close as possible to the diameter of the reinforcing bar. Prior to 5 4 installing check the capsule to be sure it is not damaged and invert several times at 6 F or above to confirm all of the resin is in a Percent of Load 3 2 INSTALLATION SPECIFICATIONS The installation requirements listed in the following tables are based on the minimum embedment depth. Adhesive mortar volume per inch is based on the use of carbide tipped masonry bits which meet ANSI Standard B tolerances. The combination of capsules to use for various embedment depths is listed in the load capacity sections which follow. To calculate the volume of adhesive mortar required for an embedment depth not listed, multiply the mortar volume per inch from the following tables by the embedment required. Select a combination of capsules using the capsule mortar volume in cubic inches. When selecting a combination of capsules, use sizes closest to the diameter of the rod to be used. For example, an installation using 3" threaded anchor rod at a 12" embedment requires 3.91 (12 x.326) cubic inches of adhesive mortar. A combination of two 3" capsule (2.5 cu. in. each) yields 4.1 cubic inches of adhesive mortar. SPECIFICATIONS FOR THREADED ROD Temperature ( F.) MAX. MORTAR ROD DRILL CAPSULE EMBED. TORQUE PER INCH SIZE DIA. SIZE DEPTH (FT.-LBS.) (CU. IN.) 3" 7/16" 3" /16" " 11/16" 5" 5" " 7" 3" 6" " 7" 7" SPECIFICATIONS FOR REINFORCING BARS *MORTAR REBAR REBAR DRILL CAPSULE EMBED. PER INCH SIZE SIZE DIA. SIZE DEPTH (CU. IN.) No. 3 3" 3" No. 4 5" No. 5 5" 3" 5" 5".176 No. 6 3" 7" 3" 6".22 No. 7 7" 7" 7".252 No *Actual adhesive mortar volume required will be less due to raised deformations on reinforcing bars. liquid state. Insert the capsule into the ;;; yyyeither end of the capsule may be inserted first. Vacuuming only is not sufficient. Blow out ;;; yyy generally do not provide enough dust removal for most drilled anchor holes. Holes should be clean and sound. Prior to installation check the capsule to be sure it is not damaged and invert several times at 6 F or above to confirm that all of the resin is in a liquid state. Insert the capsule into the cleaned anchor hole. Be careful to observe the direction of insertion. The arrow on the capsule should point toward the bottom of the hole. Drive the threaded rod or reinforcing bar into the anchor hole through the capsule until it ;;; yyy fully embedded. A 2 pound hammer and eye protection are recommended. A rotary hammer set in the hammering only mode and ;;; yyystud drive adapters can also be used. Stop driving immediately upon reaching the bottom of the anchor hole. Allow the Hammer-Capsule to cure for specified time before loading anchor. Do not disturb the rod once the material has begun to ;;; yyy

4 25 PERFORMANCE DATA ULTIMATE LOAD CAPACITIES - THREADED ROD IN CONCRETE The following capacities are the ultimate or failure load for the Hammer-Capsule adhesive when tested with high strength anchor rod in several compressive strengths of concrete. The capacity of the anchor rod should be taken into account in the design of any anchorage. The combinations of capsules shown are required to ensure that the proper bond area is achieved. Do not attempt to use more than two capsules. ANCHOR DRILL EMBED. MAX. TORQUE CAPSULES 2, PSI CONCRETE 3, PSI CONCRETE 4, PSI CONCRETE 5, PSI CONCRETE 6, PSI CONCRETE SIZE BIT DEPTH RANGE REQUIRED TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR (IN) (IN) (IN) (FT-LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) 3 7/ One 3" 4,92 4,44 5,88 4,44 6,12 4,44 7,175 4,44 8,21 4,44 3 7/ Two 3" 9,84 4,44 11,76 4,44 12,24 4,44 14,35 4,44 16,42 4,44 1 9/ One 8,235 1,72 1,335 1,72 11,48 1,72 12,84 1,72 14,2 1,72 1 9/ Two 16,47 1,72 2,67 1,72 22,96 1,72 25,68 1,72 28,4 1, / One 5" 1,16 17,16 13,8 17,16 15,16 17,16 17,41 17,16 19,66 17, / Two 5" 2,32 17,16 26,16 17,16 3,32 17,16 34,82 17,16 39,32 17, One 3" 13,8 24,99 17,125 24,99 17,99 24,99 19,19 24,99 2,39 24, Two 3" 26,16 24,99 34,25 24,99 35,98 24,99 38,38 24,99 4,78 24, One 7" 16,265 35,6 21,65 35,6 24,64 35,6 28,425 35,6 32,21 35, Two 7" 32,53 35,6 42,13 35,6 49,28 35,6 56,85 35,6 64,42 35, One 28,72 46,84 32,265 46,84 32,495 46,84 35,25 46,84 37,92 46, Two 57,44 46,84 64,53 46,84 64,99 46,84 7,41 46,84 75,84 46, Two 58,16 49,5 64,775 49,5 65,68 49,5 71,1 49,5 76,1 49,5 ALLOWABLE LOAD CAPACITIES - THREADED ROD IN CONCRETE The allowable bond strengths in the following table are based on applying a minimum safety factor of 4 to the ultimate load capacities for several compressive strengths of concrete. Depending upon anchor application and governing building code, higher factors of safety may be recommended. The design professional familiar with the actual product installation should be consulted. Please refer to the general section entitled Evaluation of Test Data that appears earlier in this manual for current industry standards. The allowable steel strength values are based on the AISC Manual of Steel Construction (Ninth Edition). Values for ASTM A193 Grade B7 steel threaded rod are based on A325 capacities. The allowable load used should be the lesser of the bond or steel strength. ALLOWABLE TENSION ANCHOR DRILL EMBED. ALL. TORQUE ALLOWABLE BOND STRENGTH ALLOWABLE STEEL STRENGTH SIZE BIT DEPTH RANGE 2, PSI 3, PSI 4, PSI 5, PSI 6, PSI ASTM A36 ASTM A37 ASTM A193 B7 AISI 34/316 SS (IN) (IN) (IN) (FT-LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS 3 7/ ,23 1,47 1,53 1,795 2,5 2,115 2,185 4,555 3,63 3 7/ ,46 2,94 3,6 3,585 4,15 2,115 2,185 4,555 3,63 1 9/ ,6 2,585 2,87 3,21 3,55 3,755 3,885 8,95 6,47 1 9/ ,115 5,165 5,74 6,42 7,1 3,755 3,885 8,95 6, / ,54 3,27 3,79 4,35 4,915 5,87 6,75 12,655 1, / ,8 6,54 7,58 8,75 9,83 5,87 6,75 12,655 1, ,27 4,28 4,495 4,795 5,95 8,455 8,75 18,225 12, ,54 8,56 8,995 9,595 1,195 8,455 8,75 18,225 12, ,65 5,265 6,16 7,15 8,5 11,51 11,95 24,85 16, ,13 1,53 12,32 14,21 16,15 11,51 11,95 24,85 16, ,18 8,65 8,125 8,8 9,48 15,35 15,55 32,4 22, ,36 16,13 16,245 17,6 18,96 15,35 15,55 32,4 22, ,54 16,195 16,42 17,775 19,25 23,485 24,295 5,615 34,42 ALLOWABLE SHEAR ANCHOR DRILL EMBED. ALL. TORQUE ALL. BOND STR. ALLOWABLE STEEL STRENGTH SIZE BIT DEPTH RANGE > 2, PSI ASTM A36 ASTM A37 ASTM A193 B7 AISI 34/316 SS (IN) (IN) (IN) (FT-LBS) (LBS) (LBS) (LBS) (LBS) (LBS) 3 7/ ,11 1,9 1,125 2,345 1,87 1 9/ ,68 1,94 2, 4,17 3, / ,29 3,25 3,13 6,52 5, ,245 4,355 4,55 9,39 6, ,9 5,93 6,135 12,78 8, ,71 7,745 8,1 16,69 11, ,375 12,1 12,515 26,75 17,73

5 26 ULTIMATE LOAD CAPACITIES - REINFORCING BAR IN CONCRETE The following capacities are the ultimate or failure loads for the Hammer-Capsule adhesive when tested with Grade 6 reinforcing bar. The steel strength values are based on ASTM Standard A 615. The ultimate tension loads for the Hammer-Capsule adhesive should be used as a guide. Actual results may vary depending on the base material condition and reinforcing bar tolerances. The combinations of capsules shown are required to ensure that the proper bond area is achieved. Do not attempt to use more than two capsules. REBAR APPROX. DRILL EMBED. CAPSULES ULTIMATE BOND STRENGTH GRADE 6 REBAR SIZE DIAM. BIT DEPTH REQUIRED 2, PSI 3, PSI 4, PSI 5, PSI 6, PSI YIELD ULT. TENSILE (IN) (IN) (IN) (LBS) (LBS) (LBS) (LBS) (LBS) STRENGTH (LBS) STRENGTH (LBS) No One 3" 7,84 1,52 13,2 13,2 13,2 6,6 9,9 No Two 3" 15,68 21,4 26,4 26,4 26,4 6,6 9,9 No One 12,72 14,125 15,19 15,19 15,19 12, 18, No Two 25,44 28,25 3,38 3,38 3,38 12, 18, No One 5" 16,16 18,28 2,28 21,84 23,4 18,6 27,9 No Two 5" 32,32 36,56 4,56 43,68 46,8 18,6 27,9 No One 3" 18,84 2,48 21,22 28,6 34,33 26,4 39,6 No Two 3" 37,68 4,96 42,44 57,2 68,66 26,4 39,6 No One 7" 21,2 22,66 25,73 34,92 38,4 36, 54, No Two 7" 42,4 45,32 51,46 69,84 76,8 36, 54, No One 22,52 26,29 35,7 38,95 47,6 47,4 71,1 No Two 45,4 52,58 7,14 77,81 95,2 47,4 71,1 ALLOWABLE LOAD CAPACITIES - REINFORCING BAR IN CONCRETE The allowable load values listed for for bond strength in tension are based on applying a minimum safety factor of 4 to the ultimate load capacities listed in the previous table. The steel strength values in tension for reinforcing bars are based upon the allowable stresses as listed in the Uniform Building Code. The allowable load should be the lesser of the bond strength or the steel strength. ALLOWABLE TENSION REBAR APPROX. DRILL EMBED. ALLOWABLE BOND STRENGTH ALLOWABALE REBAR STRENGTH SIZE DIAM. BIT DEPTH 2, PSI 3, PSI 4, PSI 5, PSI 6, PSI GRADE 4 GRADE 6 (IN) (IN) (IN) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) (LBS) No ,96 2,63 3,3 3,3 3,3 2,2 2,64 No ,92 5,26 6,6 6,6 6,6 2,2 2,64 No ,18 3,53 3,795 3,795 3,795 4, 4,8 No ,36 7,6 7,595 7,595 7,595 4, 4,8 No ,4 4,57 5,7 5,46 5,85 6,2 7,44 No ,8 9,14 1,14 1,92 11,7 6,2 7,44 No ,71 5,12 5,35 7,15 8,58 8,8 1,56 No ,42 1,24 1,61 14,3 17,165 8,8 1,56 No ,3 5,665 6,43 8,73 9,6 12, 14,4 No ,6 11,33 12,865 17,46 19,2 12, 14,4 No ,63 6,572 8,765 9,725 11,9 15,8 18,96 No ,26 13,145 17,535 19,45 23,8 15,8 18,96 ALLOWABLE LOAD CAPACITIES - REINFORCING BAR IN CONCRETE ALLOWABLE SHEAR The allowable load values for bond strengths in shear are based on applying a minimum safety factor of 4 to the average ultimate load capacities for the tests conducted with high strength ASTM A193 Grade B7 steel threaded rod. The allowable reinforcing bar strength based on the allowable stresses listed in the Uniform Building Code. The shear-friction coefficient for normal weight concrete was.6. The allowable shear load is based on applying the allowable shear stress to the cross sectional area of the bar and then factoring by the shear-friction coefficient. The allowable shear load chosen should be the lesser of the bond strength or the steel strength. REBAR APPROX. DRILL EMBED. ALL. BOND STR. ALLOWABLE REBAR STRENGTH SIZE DIAM. BIT DEPTH > 2, PSI GRADE 4 GRADE 6 (IN) (IN) (IN) (LBS) (LBS) (LBS) No ,11 1,32 1,585 No ,68 2,4 2,88 No ,29 3,72 4,465 No ,245 5,28 6,335 No ,9 7,2 8,64 No ,71 9,48 11,375

6 27 ULTIMATE LOAD CAPACITIES IN GROUT FILLED BLOCK The following ultimate loads are based on tests conducted using threaded rods installed in a wall constructed from C-9 hollow block completely and solidly filled with fine grout. The embedment depths were based on the use of a single capsule. Depending upon anchor application and governing building code, ultimate load capacities should be reduced by a minimum safety factor of 5 or greater to determine the allowable working load. The design professional familiar with the actual product installation should be consulted. Refer to the general section entitled Evaluation of Test Data that appears earlier in this manual for current industry standards. Experience has shown that the consistency of grout filled block varies widely. The capacities listed in this table should be used as a guide. Job site tests should be conducted to determine actual anchor load capacities and verify the suitability of the block wall. ANCHOR HOLE EMBED. GROUT FILLED BLOCK SIZE DIA DEPTH TENSION SHEAR (IN) (IN) (IN) (LBS.) (LBS.) 3 7/ ,25 4,5 1 9/ ,95 6, /16 5 1,62 9, ,46 11,84 DESIGN CRITERIA BASE MATERIAL THICKNESS The minimum recommended thickness of solid concrete or masonry base material, BMT, when using an adhesive anchor is 125% of the embedment to be used. For example, when installing an anchor to a depth of 4", the base material should be at least 5" thick. Conversely, the maximum embedment should be 8% of the base material thickness. If a concrete slab is 1" thick, an 8" depth would be the maximum recommended anchor embedment. This does not apply to products designed for installation in hollow base materials. Where: Ts = Applied Service Tension Load TA = Allowable Tension Load Vs = Applied Service Shear Load VA = Allowable Shear Load Dependent upon the election to conduct certain optional independent test procedures, many ICBO evaluated products are currently analyzed more conservatively with the following proportion. T S T () S VS () V A T () S VS () V A + 1 (straight line) T 5 /3 () S VS () V A (parabolic) V S V A 5 /3 + 1 S S E D = Anchor Size S = Spacing E = Edge Distance BMT = Base Material Thickness COMBINED LOADING For anchors loaded in both shear and tension, the combination of loads should be proportioned as follows based on the Uniform Building Code: T 5 /3 () S VS () V A 5 /3 + 1 E D S BMT S ADHESIVE ANCHOR SPACING AND EDGE DISTANCE Adhesive type anchors can be installed closer to the edge of a concrete slab than mechanical anchors with no cracking of the base material. The published ultimate and allowable working loads are based on testing conducted at the spacing and edge distance required to obtain maximum load and should be reduced to account for decreased spacing and edge distance. The reduction load factors listed are cumulative. For example, the allowable working load for an anchor which is installed at a spacing and an edge distance less than that required for maximum load capacity would be multiplied by the appropriate factor from both the spacing and edge distance tables. The factors are normally applied to the allowable working load of the adhesive resin and then compared to the allowable strengths of the steel anchor rods used. See the Design Example featured earlier in this manual. SPACING BETWEEN ADHESIVE ANCHORS The following table lists the load reduction factor, Rs, for each anchor diameter, D, based on the center to center anchor spacing. To obtain the maximum working load in tension or shear, a spacing of 8 anchor diameters (8D) or

7 28 greater should be used. The minimum recommended anchor spacing is 4 anchor diameters (4D) at which point the allowable working load for the adhesive resin should be reduced by 3%. Anchor spacing closer or less than 4 diameters (4D) need to be field tested. Actual base material conditions will determine any applicable reduction factor. The following table lists the load reduction factor, Rs, for each anchor diameter, D, based on the center to center anchor spacing. 1" 9" 8" 7" 6" S 5" 4" 3" 2" ANCHOR ANCHOR SPACING, S (INCHES) SIZE TENSION AND SHEAR D 8D 7D 6D 5D 4D Rs EDGE DISTANCE FOR ADHESIVE ANCHORS EDGE DISTANCE - TENSION R S For adhesive anchors loaded in tension, the following table lists the load reduction factor, Re, for each anchor diameter, D, based on the anchor center to edge distance. To obtain the maximum tension load, an edge distance of 6 anchor diameters (6D) and greater should be used. The minimum recommended edge distance is 4 anchor diameters (4D) at which point the allowable working load for the adhesive resin should be reduced by 4%. Edge distances closer or less than 4 diameters (4D) need to be field tested. Actual base material conditions will determine any applicable reduction factor. The 7 " 5 " following table lists the load reduction factor, Re, for each anchor diameter, D, based on the anchor center to edge distance. E ANCHOR EDGE DISTANCE, E (INCHES) SIZE TENSION ONLY D 6D 5D 4D Re EDGE DISTANCE - SHEAR The following table lists the load reduction factor, Re, for each anchor diameter, D, based on the anchor center to edge distance. To obtain the maximum shear E 1" 9" 8" 7" 6" 5" 4" 3" 2" 2" 18" 16" 14" 12" 1" 8" 6" 4" 2" R e " 5 " R e " 5 "

8 29 load, an edge distance of 12 anchor diameters (12D) and greater should be used. The minimum recommended edge distance is 4 anchor diameters (4D) at which point the allowable working load for the adhesive resin should be reduced by 5%. Edge distances closer or less than 4 diameters (4D) need to be field tested. Actual base material conditions will determine any applicable reduction factor. The following table lists the load reduction factor, Re, for each anchor diameter, D, based on the anchor center to edge distance. ANCHOR EDGE DISTANCE, E (INCHES) SIZE SHEAR ONLY D 12D 11D 1D 9D 8D 7D 6D 5D 4D Re SPECIAL APPLICATIONS INSTALLATION OF ANCHORS UNDER WATER The Hammer-Capsule system can be used to install threaded anchor rod or reinforcing bars in submerged applications under water provided some installation and design criteria are followed. A mock installation should be attempted to determine whether the anchor rod can be properly driven through the Hammer-Capsule. The anchor holes should be prepared following the standard installation procedures with the following exceptions. Anchor holes should be drilled at least deeper than the standard embedment depth to insure proper dispersion of the hardener. Special care should be taken to clean the anchor hole as a slurry of concrete paste tends to form on the walls of the anchor hole when drilling under water. Insert the proper size capsule into the anchor hole. Be sure the capsule is fully inserted to the bottom of the hole. Follow the standard installation guidelines for driving the anchor rod used into the capsule. The setting time of the Hammer-Capsule adhesive in submerged applications depends upon the base material temperature as shown previously. Laboratory tests and field experience have shown that a decrease of 3 to 4% in the ultimate tension load capacity can be expected for a Hammer- Capsule anchor which is installed under water. The design professional should include this reduction in his calculations. If the tension capacities are critical, a job site test is recommended. INSTALLATION OF ANCHORS OVERHEAD Prior to installing adhesive anchors overhead or in walls, consult with the governing building authority to determine the requirements for fire safety guidelines. The effect of elevated temperature on the Hammer-Capsule adhesive is shown in the Adhesive Properties. The Hammer-Capsule system can be used for the installation of threaded anchor rod overhead. The anchor holes should be prepared following the standard procedures with the following exceptions. After the anchor hole is drilled and cleaned, insert the proper size capsule into the hole. For the 3" to sizes, select the proper size anchor seal plug and insert it into the hole until the rim of the plug is fully seated against the base material. Be sure the hole is deep enough to accept both the capsule and the plug. Following the standard installation instructions, drive the anchor rod through the cross cut opening of the anchor seal plug into the capsule. An alternate method is to use a piece of duct tape or similar material to hold the capsule in place prior to driving the anchor rod into the hole. If this method is used, it will be necessary to hold the anchor rod in place until the adhesive gels. SUGGESTED SPECIFICATION The adhesive used shall be a two part capsule type system containing an acrylic epoxy resin (vinyl ester). The lower portion of the capsule shall contain the resin in which quartz aggregate shall be suspended while the upper portion of the capsule shall contain a mixture of dibenzoyl peroxide hardener and aggregate. Proper mixing of the capsule components shall be accomplished by driving straight cut anchor rod into the capsule without any spinning action or special tools. The capsule used shall have a minimum shelf life of two years. Anchor holes shall be drilled with a bit meeting the requirements of ANSI Standard B and shall be approved by the manufacturer. The adhesive capsule and anchor hardware components shall be installed according to the manufacturers instructions. Anchor rods (or inserts) shall be manufactured from steel. Hammer-Capsule anchors and the hardware used (except for reinforcing bar) shall be supplied by Powers Fasteners Inc.

Chem-Stud CHEMICAL SPIN TYPE CAPSULE ADHESIVE PRODUCT DESCRIPTION CHEM-STUD ADHESIVE PROPERTIES

Chem-Stud CHEMICAL SPIN TYPE CAPSULE ADHESIVE PRODUCT DESCRIPTION CHEM-STUD ADHESIVE PROPERTIES 192 Chem-Stud SPIN TYPE CAPSULE ADHESIVE BASE MATERIAL Solid Concrete SIZE RANGE 3" to 1-1" Anchor Rod, No. 3 to No.10 Reinforcing Bar ANCHOR MATERIAL Ester Based Resin PRODUCT DESCRIPTION The Chem-Stud

More information

CHEMICAL /4" 3/8" to 5/8" /8" 3/4" to 1-1/4" 1 10

CHEMICAL /4 3/8 to 5/8 /8 3/4 to 1-1/4 1 10 194 ASTM A193 GRADE B7 HIGH-STRENGTH CARBON, ZINC PLATED (ASTM B 633 YELLOW DICHROMATE) B7 (AISI 414) anchor rod is supplied with nuts meeting the requirements of ASTM Specification A 194, Grade 2H (ASTM

More information

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1.

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1. The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.1. Please refer to the publication in its entirety for complete details on this product

More information

High Strength Epoxy Tested in Accordance with ICC-ES AC308

High Strength Epoxy Tested in Accordance with ICC-ES AC308 ADHESIVE ANCHORING SPECIALISTS DESCRIPTION/SUGGESTED SPECIFICATIONS* The 100% epoxy resin and hardener are completely mixed as they are dispensed from the dual cartridge through a static mixing nozzle,

More information

AC50 Silver Adhesive Anchoring System

AC50 Silver Adhesive Anchoring System General Information General Information AC50 Silver Adhesive Anchoring System Product Description The AC50 Sliver is a two-component, adhesive anchoring system. The system includes injection adhesive in

More information

High Strength Epoxy Tested in Accordance with ICC-ES AC308

High Strength Epoxy Tested in Accordance with ICC-ES AC308 ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy Tested in Accordance with ICC-ES AC308 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are completely mixed as they are dispensed from

More information

Hilti, Inc South 122 nd East Avenue Tulsa, OK

Hilti, Inc South 122 nd East Avenue Tulsa, OK Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,

More information

Easy to Use A7 Saves You Time and Money

Easy to Use A7 Saves You Time and Money ADHESIVE ANCHORING SPECIALISTS Easy to Use Saves You Time and Money DESCRIPTION/SUGGESTED SPECIFICATIONS* Fast Dispensing, Fast Curing The acrylic resin and hardening agent are completely mixed as they

More information

High Strength Epoxy tested in accordance to ICC-ES AC308

High Strength Epoxy tested in accordance to ICC-ES AC308 ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are

More information

C6+ High Strength Epoxy for All. conditions. One product for most environmental conditions and weather conditions. Curing Times

C6+ High Strength Epoxy for All. conditions. One product for most environmental conditions and weather conditions. Curing Times ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy for All Conditions DESCRIPTION/SUGGESTED SPECIFICATIONS* One product for most environmental conditions and weather conditions Design and use with confidence

More information

Submittal Information

Submittal Information Steel beam & columns Mounting machinery to concrete slab Contents CAS Number Epoxy resin Trade Secret Curing Agent Trade Secret Washed sand 14808-60-7 Recognized Worldwide Te ste d b y W arrin gto n Full

More information

Styrene free Urethane hybrid adhesive

Styrene free Urethane hybrid adhesive T E C H N I C A L D A T A S H E E T Styrene free Urethane hybrid adhesive CONTENT PAGE Application in noncracked concrete Application in cracked concrete Post-installed rebar Application under Seismic

More information

High Strength Epoxy tested in accordance to ICC-ES AC308

High Strength Epoxy tested in accordance to ICC-ES AC308 ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are

More information

Adhesive Anchoring Selection Guide Solid Concrete Applications

Adhesive Anchoring Selection Guide Solid Concrete Applications ADHESIVE ANCHORING SPECIALISTS Adhesive Anchoring Selection Guide Solid Concrete Applications Doweling into Concrete with Rebar ultimate tensile product systems key features properties performance 1,2

More information

Sormat ITH-Ve PRODUCT DATA SHEET. ITH-Ve - VINYLESTER BASED RESIN STYRENE FREE. Vinylester based injection resin, styrene free

Sormat ITH-Ve PRODUCT DATA SHEET. ITH-Ve - VINYLESTER BASED RESIN STYRENE FREE. Vinylester based injection resin, styrene free ITH 280 Ve ITH 300 Ve ITH 345 Ve ITH 410 Ve Application in noncracked concrete Post-installed rebar Content Page Product description 2 Properties and benefits 2 Handling and storage 2 Applications and

More information

PROJECT SUBMITTAL. Power-Stud TM. Wedge Expansion Anchor PROJECT SUBMITTAL CONTENTS APPROVALS AND LISTINGS

PROJECT SUBMITTAL. Power-Stud TM. Wedge Expansion Anchor PROJECT SUBMITTAL CONTENTS APPROVALS AND LISTINGS PROJECT SUBMITTAL Power-Stud TM Wedge Expansion Anchor Anchoring into Solid Concrete and Masonry Base Materials Anchor Diameter is the Same as the Hole Diameter Interlocking Clip Wedges Prevent Anchor

More information

ESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year.

ESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year. ESR-1967 Reissued January 1, 2008 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California

More information

CIA-GEL 7000 EPOXY. One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY

CIA-GEL 7000 EPOXY. One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY CIA-GEL 000 EPOXY One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY City of Los Angeles Research Report No. (in Concrete, Block and Brick) City of Los Angeles Research

More information

ET Epoxy-Tie Anchoring Adhesive

ET Epoxy-Tie Anchoring Adhesive ET Epoxy-Tie is a two-component, high solids, epoxy-based system for use as a high-strength, non-shrink anchor grouting material. Resin and hardener are dispensed and mixed simultaneously through the mixing

More information

CHEMSET 801 XTREM TECHNICAL DATA SHEET. Fast Setting Vinyl Ester For Extreme Anchoring Applications

CHEMSET 801 XTREM TECHNICAL DATA SHEET. Fast Setting Vinyl Ester For Extreme Anchoring Applications Date of Issue: April 27, 2016 Fast Setting Vinyl Ester For Extreme Anchoring Applications CHEMSET 801 XTREM is a heavy duty Vinyl Ester mortar certified for challenging engineering design conditions such

More information

Trutek TCM380 PRO. Trutek Fasteners Polska Al. Krakowska 55 Sekocin nowy Rasxyn Poland T:

Trutek TCM380 PRO. Trutek Fasteners Polska Al. Krakowska 55 Sekocin nowy Rasxyn Poland T: Features and Benefits Version 23/12/2013 High bond strength with High load resistance Used with all grades of threaded rod and rebar in accordance with TR029 Used in non-cracked and cracked concrete Fast

More information

AC100+ GOLD Vinylester Injection Adhesive Anchoring System

AC100+ GOLD Vinylester Injection Adhesive Anchoring System GENERAL INFORMATION GENERAL INFORMATION AC100+ GOLD Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC100+ Gold is a two-component vinylester adhesive anchoring system. The system

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: ITW RED HEAD 700 HIGH GROVE BOULEVARD GLENDALE HEIGHTS, ILLINOIS 60139

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: ITW RED HEAD 700 HIGH GROVE BOULEVARD GLENDALE HEIGHTS, ILLINOIS 60139 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (00) 423-657 (562) 699-0543 www.icc-es.org ESR-4109 Issued 09/2017 This report is subject to renewal 09/201. DIVISION: 04 00 00 MASONRY

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 587 (52) 99 0543 www.icc es.org ESR 393 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 04 00 00 MASONRY

More information

AC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS

AC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS Vinylester Injection Adhesive Anchoring System PACKAGING Coaxial Cartridge 5 fl. oz. (150 ml or 9.2 in 3 ) 10 fl. oz. (280 ml or 17.1 in 3 ) Dual (Side-by-Side) Cartridge 8 fl. oz. (235 ml or 14.3 in 3

More information

AC200+ Acrylic Injection Adhesive Anchoring System

AC200+ Acrylic Injection Adhesive Anchoring System GENERAL INFORMATION GENERAL INFORMATION AC200+ Acrylic Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC200+ is a two-component, high strength adhesive anchoring system. The system includes

More information

FIVE STAR PRODUCTS, INC. (800)

FIVE STAR PRODUCTS, INC.  (800) FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 Page 1 of 11 DESIGN-A-SPEC GUIDELINES FIVE STAR RS ANCHOR GEL CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS PART

More information

US Pool Lift Model #114 (Independence) Installation Guide

US Pool Lift Model #114 (Independence) Installation Guide US Pool Lift Model #114 (Independence) Installation Guide This manual has been provided to assist with lift installation. For further assistance please contact your authorized US Pool Lift dealer. Toll

More information

CONCRETE ANCHORING SYSTEMS

CONCRETE ANCHORING SYSTEMS CONCRETE ANCHORING SYSTEMS Notes RH 2 CONCRETE ANCHORING SYSTEMS TABLE OF CONTENTS Anchoring Working Principles... RH 4 Red Head Adhesive Anchoring Systems... RH 7 Adhesive Anchoring Selection Guide...

More information

Trusted ICC ES HILTI, INC. SYSTEM E ANCHOR. Conformity! Look. Evaluation. ICC-ES Evaluation

Trusted ICC ES HILTI, INC. SYSTEM E ANCHOR. Conformity! Look. Evaluation. ICC-ES Evaluation 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 2682 Reissued 08/2016 This report is subject to renewal 08/2018. DIVISION: 04 00

More information

LOW VISCOSITY STRUCTURAL EPOXY. Table of Contents. Made in the U.S.A. AF35LVE TECHNICAL DATA SHEET

LOW VISCOSITY STRUCTURAL EPOXY. Table of Contents. Made in the U.S.A. AF35LVE TECHNICAL DATA SHEET 1 Table of Contents PRODUCT DESCRIPTION PRODUCT NUMBER GENERAL USES AND APPLICATIONS ADVANTAGES AND FEATURES STANDARDS AND APPROVALS AVAILABILITY COLOR AND RATIO INSTALLATION AND COVERAGE STORAGE/SHELF

More information

Preferred. Steel, Epoxy Powder Coated. Satisfactory. Limited

Preferred. Steel, Epoxy Powder Coated. Satisfactory. Limited Corrosion Resistance We manufactures enclosures from a wide range of materials, offering varying degrees of resistance against chemical corrosion. All materials are affected by corrosion in some manner.

More information

Chem-Stud Chem-Stud 56.1 Introduction Product Description Chem-Stud Capsule Specifications. Chem-Stud Recommended Setting Time

Chem-Stud Chem-Stud 56.1 Introduction Product Description Chem-Stud Capsule Specifications. Chem-Stud Recommended Setting Time 56.0 Chem-Stud 56.1 Introduction The Chem-Stud Anchor System consists of sef contained two-part gass capsues and matching chise pointed anchor rod which is instaed using a rotary hammer dri and rod adapters.

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3200 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 04 00

More information

High-performance anchoring adhesive. n Styrene-free n Low odour n Low wastage n No transportation restrictions

High-performance anchoring adhesive. n Styrene-free n Low odour n Low wastage n No transportation restrictions Product Data Sheet Edition 23/12/2008 Identification no: 02 04 02 06 001 0 000020 Sika AnchorFix -2 Sika AnchorFix -2 High-performance anchoring adhesive Construction Description Uses Characteristics /

More information

Anchor Classifications...1. Anchor Behavior...2. Anchor Failure Modes...2. Anchor Capacity...3. Load Conditions...4

Anchor Classifications...1. Anchor Behavior...2. Anchor Failure Modes...2. Anchor Capacity...3. Load Conditions...4 Table of Contents Architect & Engineering Guide 7 Anchor Classifications............................................1 Anchor Behavior.................................................2 Anchor Failure Modes.............................................2

More information

TITEN HD Heavy Duty Screw Anchor for Concrete & Masonry

TITEN HD Heavy Duty Screw Anchor for Concrete & Masonry TITEN HD Heavy Duty Screw Anchor for & Masonry The Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4105 Issued 08/2017 This report is subject to renewal 08/2018. DIVISION: 04 00 00

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-4143 Issued 01/2018 This report is subject to renewal 01/2019. DIVISION: 04 00 00

More information

Hilti HIT-RE 500 post-installed rebars

Hilti HIT-RE 500 post-installed rebars Injection mortar system Benefits Hilti HIT-RE 500 330 ml foil pack (also available as 500 ml and 1400 ml foil pack) Static mixer - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity

More information

VF22PRO Chemical Injection System STYRENE-FREE INJECTION SYSTEM - VINYLESTER

VF22PRO Chemical Injection System STYRENE-FREE INJECTION SYSTEM - VINYLESTER CHEMICAL ANCHORING SYSTEMS TECHNICAL DATA SHEET VF22PRO Chemical Injection System STYRENE-FREE INJECTION SYSTEM - VINYLESTER STYRENE FREE - STYRENE FREE - LOW VOC VF22PRO is a versatile high-strength two-part

More information

Legacy report on the 1997 Uniform Building Code, the 2000 International Building Code and the 2000 International Residential Code.

Legacy report on the 1997 Uniform Building Code, the 2000 International Building Code and the 2000 International Residential Code. LEGACY REPORT ER-2895 Reissued March 1, 2004 www.icc-es.org Business/Regional Office 5360 Workman Mill Road, Whittier, California 90601 (562) 699-0543 Regional Office 900 Montclair Road, Suite A, Birmingham,

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3342 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 04 00

More information

CRESTONE STRAIGHT FIRE PIT SKU:

CRESTONE STRAIGHT FIRE PIT SKU: CRESTONE STRAIGHT FIRE PIT SKU: 198-6257 Approximate Weight: 2200 lbs. Approximate Size: 4 8 Exterior Dimension x 3 Interior Dimension x 1 4 H www.midwestmanufacturing.com CRESTONE BLOCK MATERIALS CONCRETE

More information

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17.

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17. The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17. Please refer to the publication in its entirety for complete details on this product

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4042 Issued 07/2017 This report is subject to renewal 07/2018. DIVISION: 04 00 00

More information

ChemSet Reo 502. Chemical Anchoring - Reinforcing Bar Anchorage 15.1 CHEMICAL INJECTION ANCHORING 15.1 GENERAL INFORMATION.

ChemSet Reo 502. Chemical Anchoring - Reinforcing Bar Anchorage 15.1 CHEMICAL INJECTION ANCHORING 15.1 GENERAL INFORMATION. 15.1 CHEMICAL INJECTION ANCHORING 15.1 GENERAL INFORMATION Product is an extra heavy duty pure epoxy anchoring adhesive. Benefits, Advantages and Features Greater productivity: Anchors in dry, damp, wet

More information

CTP STITCH-TIE AGAIN! Quick and easy way to re-anchor existing veneers to back-up structures.

CTP STITCH-TIE AGAIN! Quick and easy way to re-anchor existing veneers to back-up structures. Helical Wall Tie System for Stabilizing Veneers and Structural Repair AGAIN! ANOTHER CTP SOLUTION! CTP STITCH-TIE Quick and easy way to re-anchor existing veneers to back-up structures. Brick to Concrete

More information

European Technical Assessment ETA-16/0865 of 08/11/2016

European Technical Assessment ETA-16/0865 of 08/11/2016 ETA-Danmark A/S Göteborg Plads 1 DK-21590 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2966 Reissued 12/2016 This report is subject to renewal 12/2017. DIVISION: 04 00 00 MASONRY

More information

Chemical Anchoring Reinforcing Bar Anchorage

Chemical Anchoring Reinforcing Bar Anchorage Introduction CHEMICAL ANCHORING - REINFORCING BAR ANCHORING Chemical Anchoring Reinforcing Bar Anchorage The following section applies to reinforcing bar in anchorage applications. For structural post-installed

More information

weber.anc 405 BFX formerly Conrep.405 BFX

weber.anc 405 BFX formerly Conrep.405 BFX 1/ weber.anc 5 BFX formerly Conrep.5 BFX PURE EPOXY ANCHORING RESIN IN CARTRIDGE PRODUCT weber.anc 5 BFX is a two-component high strength pure epoxy chemical anchoring resin system. It is especially recoended

More information

Anti-Corrosive Heat Resistant Chain

Anti-Corrosive Heat Resistant Chain ANTI-CORROSIVE / HEAT RESISTANT CHAIN Anti-Corrosive Heat Resistant Chain ULTRA WP CHAIN ULTRA WP chain resists corrosion when exposed to harsh outdoor environments, including seawater. The exclusive ULTRA

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3196 Reissued 10/2017 This report is subject to renewal 10/2018. SECTION: 04 05 19.16

More information

APPENDIX A: Strength Design Performance Values

APPENDIX A: Strength Design Performance Values ADHESIVE ANCHORING SPECIALISTS APPENDIX A: Strength Design Performance Values SPECIFICATIONS AND DETAILS FOR INSTALLATION OF ANCHORS IN CONCRETE WITH G ADHESIVE Threaded Rod Diameter (d) /8 / /8 / 7/8

More information

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS 0 Most Widely Accepted and Trusted ICC ES Listing Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ELC 1917 Reissued 9/2017 This listing is subject to renewal 9/2018. DIVISION: 03 00 00 CONCRETE

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 687 (6) 699 0 www.icc es.org ESR 8 Reissued 0/08 This report is subject to renewal 0/09. DIVISION: 0 00 00 MASONRY SECTION:

More information

Construction. Universal anchoring adhesive. Product Description. Tests. Product Data Sheet Edition _1. 1 Sika AnchorFix S 1/6

Construction. Universal anchoring adhesive. Product Description. Tests. Product Data Sheet Edition _1. 1 Sika AnchorFix S 1/6 Product Data Sheet Edition 2014-01_1 Sika AnchorFix S Sika AnchorFix S Universal anchoring adhesive Product Description Styrenated polyester based two part anchoring adhesive. Construction Uses Characteristics

More information

PE1000+ High Strength Epoxy Anchoring System

PE1000+ High Strength Epoxy Anchoring System 42 PE000+ High Strength Epoxy Anchoring System PRODUCT DESCRIPTION The PE000+ is a twocomponent, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing

More information

SURFACE PREPARATION INSTRUCTIONS: CONCRETE

SURFACE PREPARATION INSTRUCTIONS: CONCRETE SURFACE PREPARATION INSTRUCTIONS: CONCRETE DEFINITION OF TERMS The terms listed will be used frequently throughout this article and listed in boldface for ease of reference. They describe, in detail, the

More information

AC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS

AC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC100+Gold is a twocomponent vinylester adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing

More information

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST-INSTALLED CONCRETE ANCHORS 0 Most Widely Accepted and Trusted ICC-ES Listing Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ELC-4027 Issued 07/2017 This listing is subject to renewal 07/2018. DIVISION: 03 00 00 CONCRETE

More information

MODEL 2639 AWWA C509 FULL BODY DUCTILE IRON MODEL 2640 AWWA C509 FULL BODY GRAY IRON

MODEL 2639 AWWA C509 FULL BODY DUCTILE IRON MODEL 2640 AWWA C509 FULL BODY GRAY IRON MODEL 2639 AWWA C509 FULL BODY DUCTILE IRON MODEL 2640 AWWA C509 FULL BODY GRAY IRON 2639-95 C 6/18/14 2 1/2"-12" R/S VALVE OS&Y EXPLODED VIEW ITEM NO. DESCRIPTION Material QTY. 1 Follower Gland Gray Iron

More information

ADVANTAGES OF POLYETHYLENE PIPES COMPARED TO PVC PIPES

ADVANTAGES OF POLYETHYLENE PIPES COMPARED TO PVC PIPES 1 ADVANTAGES OF POLYETHYLENE PIPES COMPARED TO PVC PIPES The main advantages and improvements in drainage networks that will be obtained by the use of PE MAGNUM pipes, in comparison to PVC pipes are: 1.

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT:

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA ROAD TOWSON, MARYLAND EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 1678 Reissued 03/2017 This report is subject to renewal 03/2018. DIVISION: 04 00 00 MASONRY

More information

European Technical Assessment ETA-14/0453 of 11/12/2014

European Technical Assessment ETA-14/0453 of 11/12/2014 ETA-Danmark A/S Göteborg Plads 1 DK-21590 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet ww.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

Sormat ITH-Pe PRODUCT DATA SHEET. ITH-Pe - POLYESTER BASED RESIN STYRENE FREE. Polyester based injection resin, styrene free. ITH 165 Pe art.

Sormat ITH-Pe PRODUCT DATA SHEET. ITH-Pe - POLYESTER BASED RESIN STYRENE FREE. Polyester based injection resin, styrene free. ITH 165 Pe art. ITH 165 Pe art. 72900 Application in noncracked concrete ITH 300 Pe art. 72940 ITH 410 Pe art. 72941 Content Page Product description 2 Properties and benefits 2 Sample applications 2 Applications and

More information

Epoxy Resin Specification Information

Epoxy Resin Specification Information Epoxy Resin Specification Information Epoxy Resin products are generally specified in sections 11600 and 12345 of most equipment specifications. Architectural Specification EPOXY RESIN WORK SURFACES shall

More information

EPCON C8. Chemical Anchoring - Reinforcing Bar Anchorage 16.1 CHEMICAL INJECTION ANCHORING

EPCON C8. Chemical Anchoring - Reinforcing Bar Anchorage 16.1 CHEMICAL INJECTION ANCHORING 16.1 CHEMICAL INJECTION ANCHORING 16.1 GENERAL INFORMATION Product is a High Performance Pure Epoxy Anchoring adhesive for use in Cracked and Non-Cracked concrete. For structures subject to external exposure,

More information

ChemSet 101 PLUS. Chemical Anchoring - Anchor Studs 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION. Product

ChemSet 101 PLUS. Chemical Anchoring - Anchor Studs 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION. Product 12.1 CHEMICAL INJECTION ANCHORING 12.1 GENERAL INFORMATION Product PERFORMANCE RELATED MATERIAL SPECIFICATION INSTALLATION RELATED ChemSet Injection 101 PLUS is a marine grade polyester adhesive. Benefits,

More information

ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS PREFACE

ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS PREFACE ICC EVALUATION SERVICE, INC. Evaluate P Inform P Protect ACCEPTANCE CRITERIA FOR FASTENERS POWER-DRIVEN INTO CONCRETE, STEEL AND MASONRY ELEMENTS AC70 Approved October 2006 Effective January 1, 2007 Previously

More information

SIMPLE CERTAINTY MAXIMUM VERSATILITY INCREASES ANCHOR RELIABILITY AND JOBSITE PRODUCTIVITY

SIMPLE CERTAINTY MAXIMUM VERSATILITY INCREASES ANCHOR RELIABILITY AND JOBSITE PRODUCTIVITY SIMPLE CERTAINTY MAXIMUM VERSATILITY INCREASES ANCHOR RELIABILITY AND JOBSITE PRODUCTIVITY QUICK-CURE ADHESIVE ANCHOR FOR CONCRETE AND MASONRY APPLICATIONS THE RELIABLE CHOICE NO LONGER REQUIRES A CHOICE

More information

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INTALLED CONCRETE ANCHORS

DIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INTALLED CONCRETE ANCHORS 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3372 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 03 00

More information

EPCON C6. Chemical Anchoring - Anchor Studs 9.1. Principal Applications CHEMICAL INJECTION ANCHORING 9.1 GENERAL INFORMATION

EPCON C6. Chemical Anchoring - Anchor Studs 9.1. Principal Applications CHEMICAL INJECTION ANCHORING 9.1 GENERAL INFORMATION 9.1 CHEMICAL INJECTION ANCHORING 9.1 GENERAL INFORMATION Product Epcon C6 is a versitile pure epoxy anchoring adhesive Benefits, Advantages and Features Features Superior strength in shallow embedment.

More information

European Technical Assessment. ETA 15/0226 of General Part TCM400PE, TCM600PE. Trade name of the construction product

European Technical Assessment. ETA 15/0226 of General Part TCM400PE, TCM600PE. Trade name of the construction product Member of Wellington, 19 ES 08018 Barcelona Tel: (+34) 93 309 34 04 qualprod@itec.cat www.itec.cat www.eota.eu European Technical Assessment ETA 15/0226 of 17.04.2015 General Part Trade name of the construction

More information

SECTION XXXX POLYMER CONCRETE PUMP STATIONS

SECTION XXXX POLYMER CONCRETE PUMP STATIONS SECTION XXXX POLYMER CONCRETE PUMP STATIONS PART 1 GENERAL 1.1 SUMMARY A. This specification shall govern for the furnishing of all work necessary for installation of polymer concrete pump stations to

More information

AC100-PRO. AC100-PRO Vinylester 160ML AC100-PRO Vinylester 300ML AC100-PRO Vinylester 360ML AC100-PRO Vinylester 410ML AC100-PRO 160ML AC100-PRO 300ML

AC100-PRO. AC100-PRO Vinylester 160ML AC100-PRO Vinylester 300ML AC100-PRO Vinylester 360ML AC100-PRO Vinylester 410ML AC100-PRO 160ML AC100-PRO 300ML Vinylester 160ML Vinylester 300ML Vinylester 360ML Vinylester 410ML 160ML 300ML 360ML 410ML Approvals and test reports POWERS TEST LABORATORY 0756-CPD-0236 EUROPEAN TECHNICAL APPROVAL ETA-08/0290 - ETAG

More information

Atlas Minerals & Chemicals, Inc. CHEMESTER MORTAR. 5-42PI ( ) Supersedes 5-42PI (2-02) & 5-44PI (2-02) PHYSICAL PROPERTIES

Atlas Minerals & Chemicals, Inc. CHEMESTER MORTAR. 5-42PI ( ) Supersedes 5-42PI (2-02) & 5-44PI (2-02) PHYSICAL PROPERTIES Atlas Minerals & Chemicals, Inc. DATA A SHEET 5-42PI (6-03 2 ) Supersedes 5-42PI (2-02) & 5-44PI (2-02) CHEMESTER MORTAR DESCRIPTION CHEMESTER MORTAR is an epoxy novolac based vinyl ester resin mortar

More information

EPCON C8. Cracked Concrete - Anchor Studs 43.1 CRACKED CONCRETE - CHEMICAL INJECTION 43.1 GENERAL INFORMATION

EPCON C8. Cracked Concrete - Anchor Studs 43.1 CRACKED CONCRETE - CHEMICAL INJECTION 43.1 GENERAL INFORMATION 43.1 CRACKED CONCRETE - CHEMICAL INJECTION 43.1 GENERAL INFORMATION Product is a High Performance Pure Epoxy ing adhesive for use in Cracked and Non-Cracked concrete. For structures subject to external

More information

Anchor Fastening Technology Manual. HIT-HY 170 mortar with rebar. Hilti HIT-HY 170 mortar with rebar (as post-installed conn.

Anchor Fastening Technology Manual. HIT-HY 170 mortar with rebar. Hilti HIT-HY 170 mortar with rebar (as post-installed conn. Anchor Fastening Technology Manual Hilti HIT-HY 170 mortar with HIT-HY 170 mortar with rebar Version 2015-12 1 February 12, 2016 Hilti HIT-HY 170 mortar with rebar (as post-installed connection) Injection

More information

RYTON (PPS) Chemical Compatibility & Chemical Resistance Chart

RYTON (PPS) Chemical Compatibility & Chemical Resistance Chart RYTON (PPS) Chemical Compatibility & Chemical Resistance Chart Explanation of Footnotes 1. Satisfactory to 72 F (22 C) 2. Satisfactory to 120 F (48 C) Ratings -- Chemical Effect A = Excellent. B = Good

More information

High-performance Anchoring Adhesive

High-performance Anchoring Adhesive Technical Data Sheet Edition 3, 2009 Identification no. 02 04 02 06 001 0 000020 Version no. 0010 Sika Anchorfix -2 High-performance Anchoring Adhesive Description Solvent- and styrene free, epoxy acrylate

More information

SECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS

SECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the

More information

EPCON C6 Series. Chemical Anchoring - Reinforcing Bar Anchorage 17.1 CHEMICAL INJECTION ANCHORING 17.1 GENERAL INFORMATION

EPCON C6 Series. Chemical Anchoring - Reinforcing Bar Anchorage 17.1 CHEMICAL INJECTION ANCHORING 17.1 GENERAL INFORMATION 17.1 CHEMICAL INJECTION ANCHORING 17.1 GENERAL INFORMATION Product Epcon C6 is a versitile pure epoxy anchoring adhesive Benefits, Advantages and Features Features Superior strength in shallow embedment.

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: POWERS FASTENERS, INC. 701 EAST JOPPA ROAD TOWSON, MARYLAND 21286

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: POWERS FASTENERS, INC. 701 EAST JOPPA ROAD TOWSON, MARYLAND 21286 0 ICC-ES Report ICC-ES (800) -687 (6) 6-0 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-678 Reissued 0/0 This report is subject to renewal 0/06 DIVISION: 0 00 00 MASONRY SECTION: 0 0.6 MASONRY

More information

Fire Sprinkler & pipe supports Cable Trays and Strut Suspended Lighting

Fire Sprinkler & pipe supports Cable Trays and Strut Suspended Lighting General Information Mechanical Anchors GENERAL INFORMATION MINI-UNDERCUT+ Internally Threaded Undercut Anchor PRODUCT DESCRIPTION The Mini-Undercut+ anchor is an internally threaded, self-undercutting

More information

CHEMCAST is the only high quality acrylic sheet that can provide you with short runs capability and color selection to fit your specific needs.

CHEMCAST is the only high quality acrylic sheet that can provide you with short runs capability and color selection to fit your specific needs. INTRODUCTION What makes CHEMCAST acrylic sheet notably different is: CHEMCAST is the only high quality acrylic sheet that can provide you with short runs capability and color selection to fit your specific

More information

Injection Adhesive VM-PY

Injection Adhesive VM-PY Cartridge VM-PY 410 Coaxial cartridge Content: 410ml Range of loading: 0,3 kn - 39,4 kn Concrete quality: C20/25 - C50/60 Masonry: Solid brick, Hollow block Description The Injection Adhesive is a polyester-resin

More information

Infrastructure Point Repair System Technical Specifications

Infrastructure Point Repair System Technical Specifications 4301 A 34 t h Street North St. Petersburg, FL 33714 PH: 877-327-4216 Fax: 727-327- 4118 Web: www.irsi.net Infrastructure Point Repair System 1. Scope: This specification defines the approved methodology

More information

System Components. Grades. General Information Installation Information

System Components. Grades. General Information Installation Information General Information SECTION CONTENTS AC100-PRO General Information Installation Information Vinylester Injection Adhesive Anchoring System Design Information ProDUCT DESCRIPTION The AC100-PRO is a two-component

More information

February 1, 2018 PARTIES INTERESTED IN ADHESIVE ANCHORS IN MASONRY ELEMENTS

February 1, 2018 PARTIES INTERESTED IN ADHESIVE ANCHORS IN MASONRY ELEMENTS February 1, 2018 TO: PARTIES INTERESTED IN ADHESIVE ANCHORS IN MASONRY ELEMENTS SUBJECT: Proposed Revisions to the Acceptance Criteria for Adhesive Anchors in Masonry Elements, Subject AC58-0218-R1 (AB/VC)

More information

High Strength Epoxy Tested in Accordance to ICC-ES AC308

High Strength Epoxy Tested in Accordance to ICC-ES AC308 ADHESIVE ANCHORING SYSTEMS DESCRIPTION/SUGGEST SPECIFICATIONS* *Suggested Specificatios see pages RH The epoxy resi ad hardeer are completely mixed as they are dispesed from the dual cartridge through

More information

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024

DIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3056 Reissued 10/2015 This report is subject to renewal 10/2017. DIVISION: 04 00 00 MASONRY

More information

C-MIX PLUS 150 ml, 300 ml and 380 ml

C-MIX PLUS 150 ml, 300 ml and 380 ml SPECIFICATIONS FOR DEFINITION, IDENTIFICATION AND USE C-MIX PLUS 150 ml, 300 ml and 380 ml Chemical sealant for hollow masonry For PERFORATED-SLEEVE, SATELIS and ID-ALL systems. NOVEMBER 2010 - VALID UNTIL

More information

HVAC Ductwork and Strut Channels Suspended Ceilings

HVAC Ductwork and Strut Channels Suspended Ceilings General Information General Information Vertigo + Rod Hanger PRODUCT DESCRIPTION Vertigo+ is a one piece, all steel threaded fastening system for suspending threaded rod in applications such as pipe hanging,

More information

LIGHTBLOCKS BOARD. stress cracking. chemical

LIGHTBLOCKS BOARD. stress cracking. chemical e info@ chemical stress cracking LIGHTBLOCKS BOARD Contents This brochure provides a summary of the chemical behavior of our semifinished product groups by listing the chemical substances ed on these materials

More information

HILTI HY 150 REBAR DESIGN GUIDE

HILTI HY 150 REBAR DESIGN GUIDE HILTI HY 150 REBAR DESIGN GUIDE HILTI HY 150 REBAR DESIGN GUIDE 1 HY150 Rebar Dowelling using Limit States Concrete Design ( A23.3-94) The design method presented here was originally based on Eurocode

More information

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.

The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. Please refer to the publication in its entirety for complete details on this product

More information

fischer Test Report Fixing Tests for

fischer Test Report Fixing Tests for fischer Test Report Fixing Tests for CONTENTS 1. Test Parameters 2. Fixings Products Tested 2.1 fischer Nylon SX Plug 2.2 fischer Nylon M Unit 2.3 fischer FFS Frame Fixing Screw 2.4 fischer FIS V 360 S

More information

Submittal / Substitution Request

Submittal / Substitution Request Submittal / Substitution Request SUBMITTED TO: To: Firm: Project: Submitted Product: SIMPSON STRONG-TIE HELI-TIE Helical Wall Tie Specified Product: Section: Page: Detail/Sheet No.: Description of Application:

More information