MOVEMENT JOINTS AND COVE-SHAPED PROFILES

Transcription

1 MOVEMENT JOINTS AND COVE-SHAPED PROFILES INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE MAINTENANCE-FREE MOVEMENT ACCOMMODATION AND COVE TREATMENT 4.4 Schluter -DILEX-MOP 4.8 Schluter -DILEX-KSN 4.11 Schluter -DILEX-HK 4.3 Schluter -DILEX-MP/-MPV 4.20 Schluter -DILEX-BT 4.22 Schluter -DILEX-HKU 4.1 Schluter -DILEX-EZ Schluter -DILEX-AS 4.21 Schluter -DILEX-AHK/-PHK 4.7 Schluter -DILEX-BWS 4.9 Schluter -DILEX-BWA 4.22 Schluter -DILEX-AHKA 4.6 Schluter -DILEX-BWB 4.9 Schluter -DILEX-KSA 4.15 Schluter -DILEX-HKS 4.18 Schluter -DILEX-AKWS 4.13 Schluter -DILEX-EKE 4.15 Schluter -DILEX-EHK 4.16 Schluter -DILEX-EDP 4.12 Schluter -DILEX-HKW

2 Movement joints are an integral part of any tile assembly. The various components of a tile assembly (tile, mortar, substrate, etc.) expand and contract according to each component s intrinsic physical properties with changes in moisture, temperature, and loading, resulting in internal stresses. Furthermore, structures that restrain overall expansion of the tile field (walls, columns, etc.) cause stress buildup within the system. If the aforementioned movements are not accommodated through the use of movement joints in the tile field and at restraining structures, the resulting stresses can cause cracking of the grout and tile and delamination of the tile from the substrate. Thus, movement joints are an essential component of any durable tile assembly. Schluter -Systems prefabricated movement joint profiles accommodate movement and protect tile edges, resulting in a permanent, maintenance-free installation. The family of Schluter -DILEX prefabricated movement profiles includes a variety of shapes, sizes, and materials to suit different applications. Application and Function Mortar Bed Joint Profiles DILEX screed joint profiles (DILEX-MOP and DILEX-MP/-MPV) are designed to provide movement joints in tile installations that are set in a mortar bed (e.g., ceramic tile, natural stone, pavers, and agglomerate tile). These profile systems are placed to produce individual fields in the assembly and feature flexible central zones to accommodate movement. DILEX mortar bed joint profiles may also be inserted in saw-cut joints or wider joints; for example, in the case of renovations. The remaining joint between the tile and the profile must be filled completely with grout or epoxy. The side sections of the profiles, made of rigid PVC, protect the edges of the adjacent covering against mechanical stresses caused by industrial traffic. However, where heavy mechanical stresses are anticipated, limitations of the PVC as edge protection must be considered. 4.4 Schluter -DILEX-MOP is available in three different heights and features stable serrated sidewalls made of rigid PVC and a central movement zone made of soft PVC. The side sections are made with environmentally friendly recycled PVC and may vary slightly in color. Since the side sections are partially exposed at the surface, DILEX-MOP is intended mainly for industrial use. 4.3 Schluter -DILEX-MP adjusts to the thickness of the mortar bed and tile surface by attaching the DILEX-MPV extensions. The profile features a central movement zone made of soft chlorinated polyethylene (CPE), which overlaps the recycled rigid PVC side sections by approximately 1/32" (1 mm), thus providing a more aesthetically pleasing exposed surface when compared to DILEX-MOP. Surface Joint Profiles Surface joints must be placed within the tiled surface regardless of substrate conditions. They provide stress relief from movements in the tile field due to thermal and moisture expansion/contraction and loading. Schluter -Systems offers a wide variety of prefabricated, maintenance-free surface movement joint profiles, suitable for applications ranging from residential to heavy commercial. Residential to Medium-duty Commercial Applications 4.1 Schluter -DILEX-EZ feature rigid PVC side walls, which are connected on top and bottom by soft PVC movement zones that form the visible surfaces. These profiles separate individual fields in the tile covering and accommodate movement through the soft PVC movement zones. Each profile features two usable surfaces in different colors for increased design options. One surface of the profile features the PVC movement zone in a solid color, while the other surface features a brass or chrome inlay embedded in the PVC movement zone. DILEX-EZ 6 and 9 are flexible and can be used to form curves. The height, H, of DILEX-EZ 6 is 1/4" (6 mm); the height, H, of DILEX-EZ 9 is 11/32" (9 mm). 4.7 Schluter -DILEX-BWS features trapezoid-perforated anchoring legs, made of recycled rigid PVC, which are secured in the mortar bond coat and provide edge protection for adjacent tiles. The profile separates individual fields in the tile covering and accommodates movement via the soft chlorinated polyethylene (CPE) movement zone, which also forms the visible surface. The movement zone is only 3/16" (5 mm) wide, matching common grout joint widths. The profile absorbs relatively limited movements, given the width of the movement zone. This should be taken into account when evaluating the requirements for a specific application. If larger movements within the covering are anticipated, the DILEX-BWS may be installed with greater frequency to create smaller fields, or the DILEX-BWB (3/8", 10 mm movement zone) may be used. DILEX-BWS is suitable for both residential and medium-duty commercial applications subject to light mechanical loads (e.g., offices and stores). The profile is also suited for exterior use. 4.6 Schluter -DILEX-BWB features trapezoid-perforated anchoring legs, made of recycled rigid PVC, which are secured in the mortar bond coat and provide edge protection for adjacent tiles. The profile separates individual fields in the tile covering and accommodates movement via the soft chlorinated polyethylene (CPE) movement zone, which also forms the visible surface. The movement zone is 3/8" (10 mm) wide, matching common movement joint widths, and is thus capable of accommodating relatively large movements. DILEX-BWB is suitable for both residential use and medium-duty commercial applications subject to light mechanical loads (e.g., offices or stores). The profile is also suited for exterior use. 2

3 4.18 Schluter -DILEX-AKWS features trapezoid-perforated anchoring legs, made of, which are secured in the mortar bond coat and provide edge protection for adjacent tiles. The profile separates individual fields in the tile covering and accommodates movement via the 1/4" (6 mm)-wide, soft PVC movement zone, which also forms the visible surface. The soft PVC movement zone is connected to the anchoring legs with rigid PVC grip bars and is not replaceable. DILEX-AKWS is suitable for both residential use and medium-duty commercial applications, such as areas subject to moderate mechanical stresses, including light vehicular traffic. In addition, DILEX-AKWS prevents sound bridges, making it ideal for use in sound-rated floors. Heavy-duty Commercial Applications 4.16 Schluter -DILEX-EDP features trapezoid-perforated anchoring legs, made of stainless steel, which are secured in the mortar bond coat and provide edge protection for adjacent tiles. The profile separates individual fields in the tile covering and accommodates horizontal movement via the stainless steel tongue-and-groove connection, which also forms the visible surface. Because the profile is designed to absorb horizontal movement only, appropriate measures must be taken to prevent the screed from moving vertically. In its base position, the visible width of the DILEX-EDP profile is 15/32" (12 mm). The profile is particularly suited for tile surfaces subject to heavy use. DILEX-EDP offers secure edge protection for surfaces exposed to continuous vehicular traffic and is, therefore, suited for use in production plants, warehouses, shopping centers, and underground parking garages, or for floor surfaces maintained with cleaning machines. 4.8 Schluter -DILEX-KSN features trapezoid-perforated anchoring legs, made of stainless steel or, which are secured in the mortar bond coat and provide edge protection for adjacent tiles. The profile separates individual fields in the tile covering and accommodates movement via the 7/16" (11 mm)-wide, soft thermoplastic rubber movement zone, which also forms the visible surface. The thermoplastic rubber movement zone can be replaced if damaged. DILEX-KSN, with stainless steel anchoring legs, offers secure edge protection for surfaces exposed to heavy-duty commercial traffic (e.g., warehouses, production facilities, or shopping malls). Schluter -DILEX-EKSB, featuring stainless steel anchoring legs, is available in 3/32" (2.5 mm), 3/16" (4.5 mm), and 1/4" (6 mm) heights to accommodate thinner floor coverings (e.g., VCT flooring or coatings). DILEX-EKSB is appropriate for residential to medium-duty commercial applications. Note: The thermoplastic rubber movement zone for DILEX-EKSB is not replaceable. Expansion Joint Profiles 4.20 Schluter -DILEX-BT features trapezoid-perforated anchoring legs, made of, which are secured in the mortar bond coat and provide edge protection for adjacent tiles against mechanical stresses. The anchoring legs can also be integrated into the mortar bed for other covering materials, such as carpeting or VCT. Therefore, the profile can move together with the respective covering assembly. The 1-3/16" (30 mm)- wide telescopic center section absorbs movements of ±7/32" (5 mm). The lateral pivot joints allow for the absorption of three-dimensional movement. DILEX-BT offers secure edge protection for surfaces exposed to foot traffic as well as vehicular traffic and is, therefore, suited for use in warehouses, production facilities, shopping centers, airports, train stations, and parking garages, or for coverings cleaned with machines. One variation of the profile, Schluter -DILEX-BT/O, can be used to create expansion joints at floor/wall transitions. A second variation, Schluter -DILEX-BTS, is added to completed surface coverings. Perimeter Joint Profiles Perimeter joints are provided at restraining elements to accommodate movements attributable to changes in moisture, temperature, and loading. DILEX perimeter movement joints are specifically designed to provide the flexible connection of tiled surfaces to fixed building elements (e.g., bathtubs, shower trays, countertops, and door and window frames) and prevent sound bridges, thereby reducing sound transmission Schluter -DILEX-AS features a trapezoid-perforated anchoring leg, made of rigid PVC, which is secured in the mortar bond coat beneath the tiles, and a flexible joining leg with self-adhesive tape to bond the profile to fixed building elements. The profile isolates the tile covering from the fixed building element and accommodates movement via the flexible joining leg, which also forms the visible surface. The profile does not replace waterproofing. Required waterproofing must be installed prior to the installation of the profile. DILEX-AS also prevents sound bridges, making it ideal for transitions in sound-rated floors. include matching end caps and inside corners. Note: DILEX-AS is suitable for tiles 3/16" to 3/8" (4 mm - 10 mm) thick. 4.9 Schluter -DILEX-BWA features a trapezoid-perforated anchoring leg, made of recycled rigid PVC, which is secured in the mortar bond coat, and a dovetailed channel, made of recycled rigid PVC, which can be bonded to fixed building elements (e.g., door and window frames, bathtubs and shower trays, countertops, etc.) using Schluter -KERDI-FIX, epoxy resin, silicone, tile adhesive, etc. The profile isolates the tile covering from the structure and accommodates movement via the 3/16 (5 mm)-wide soft chlorinated polyethylene (CPE) movement zone, which also forms 3

4 the visible surface. The lower CPE movement zone is slit to maximize the absorption of movement. DILEX-BWA also prevents sound bridges, making it ideal for transitions in sound-rated floors. surface water penetration and features a tile pocket that hides cut tile edges. In addition, it prevents sound bridges, making it ideal for floor/wall transitions in sound-rated floors. DILEX-HK include: inside and outside corners, connectors, and end caps. 4.9 Schluter -DILEX-KSA features a trapezoid-perforated anchoring leg, made of stainless steel or, which is secured in the mortar bond coat and provides edge protection for adjacent tiles, and a self-adhesive backing strip which can be bonded to fixed building elements (e.g., door and window frames, bathtubs and shower trays, countertops, etc.). The profile isolates the tile covering from the structure and accommodates movement via the 3/8" (10 mm)-wide, soft thermoplastic rubber movement zone, which also forms the visible surface. The thermoplastic rubber movement zone can be replaced if damaged. DILEX-KSA uses the same anchoring leg as DILEX-KSN to allow for the same appearance throughout an installation. DILEX-KSA also prevents sound bridges, making it ideal for transitions in sound-rated floors. Cove-shaped Profiles Ceramic cove base represents a neat, hygienic method for treating transitions by providing a curved surface that prevents the collection of dirt and is easy to clean. However, the limited availability of ceramic trim pieces has resulted in the use of sealant and caulk to treat such transitions. These joints must be continually maintained throughout the life of the installation. DILEX cove-shaped profiles provide an attractive, clean, and maintenance-free alternative for inside wall corners and floor/wall (including countertop/backsplash) transitions. They also allow the use of any tile line, regardless of the availability of trim pieces Schluter -DILEX-EKE features trapezoid-perforated anchoring legs, made of recycled rigid PVC, which are secured in the mortar bond coat. The profile separates tile fields that meet at inside corners and accommodates movement via the 3/16" (5 mm)-wide soft chlorinated polyethylene (CPE) movement zone, which forms the visible surface and creates a discrete, uniform joint. DILEX-EKE prevents Schluter -DILEX-HKW features trapezoid-perforated anchoring legs, made of recycled rigid PVC, which are secured in the mortar bond coat, and a rigid PVC cove section that accommodates minor movements and forms the visible surface. The profile s 11/16" (18 mm) radius prevents the accumulation of dirt and makes cleaning simple. The profile separates tile fields that meet at inside corners where limited movement is expected. DILEX-HKW prevents surface water penetration and meets the maintenance and hygienic requirements of commercial kitchens, bathrooms, and foodprocessing plants, or any tiled environment where a sanitary cove base is desired. DILEX-HKW features anchoring legs with equal U dimensions and is, therefore, ideal for floor/wall transitions where floor and wall tiles are the same thickness. for the DILEX-HKW include: inside and outside corners, and end caps Schluter -DILEX-HK features trapezoid-perforated anchoring legs, made of recycled rigid PVC, which are secured in the mortar bond coat. The profile separates tile fields that meet at inside corners and accommodates movement via the soft chlorinated polyethylene (CPE) cove-shaped movement zone that forms the visible surface. DILEX-HK provides an 11/16" (18 mm) radius to prevent the accumulation of dirt and to make cleaning simple. DILEX-HK prevents surface water penetration and meets the maintenance and hygienic requirements of commercial kitchens, bathrooms, foodprocessing plants, or any tiled environment where a sanitary cove base is desired. It accommodates wall and floor tiles of dissimilar thicknesses and features a tile pocket that hides cut tile edges. DILEX-HK integrates with DILEX-HKW where cove trim for inside wall corners is desired. In addition, DILEX-HK prevents sound bridges, making it ideal for floor/wall transitions in sound-rated floors. for the 4.22 Schluter -DILEX-HKU features a single trapezoid-perforated anchoring leg that turns inward, which is secured in the mortar bond coat, and a stainless steel cove section that forms the visible surface. The profile s 3/8" (10 mm) or 1-13/32" (36 mm) radius prevents the accumulation of dirt and makes cleaning simple. The profile separates tile fields that meet at inside corners where limited movement is expected. DILEX-HKU may be used with floor coverings other than ceramic and stone tile, provided that the coverings are fastened or adhered (i.e., no floating floors). DILEX-HKU prevents surface water penetration and meets the maintenance and hygienic requirements of commercial kitchens, bathrooms, food-processing plants, or any tiled environment where a sanitary cove is desired. available for the DILEX-HKU include inside and outside corners, connectors, and end caps. AHK PHK 4.21 Schluter -DILEX-AHK/-PHK features a single trapezoid-perforated anchoring leg, which is secured in the mortar bond coat and a cove section that forms the visible surface. The profile s 3/8" (10 mm) radius makes DILEX-AHK/-PHK an attractive option for countertop/backsplash transitions, as it prevents the accumulation of dirt and makes cleaning simple. The profile separates tile fields that meet at inside corners where limited movement is expected. DILEX-AHK/-PHK prevents surface water penetration and meets the maintenance and hygienic requirements of commercial kitchens, bathrooms, and food-processing plants, or any tiled environment where a sanitary cove base is desired. DILEX-AHK is available in and Tuscan color-coated, while DILEX-PHK is made of rigid PVC with a pre-colored, rigid PVC cove section. for DILEX-AHK/- PHK include: inside and outside corners, connectors, and end caps. Outside corners to integrate with Schluter -QUADEC are available for DILEX-AHK only.

5 4.22 Schluter -DILEX-AHKA is an, cove-shaped profile for transitions between walls to be tiled and previously finished floors. The profile features a single trapezoid-perforated anchoring leg that is secured in the mortar bond coat and a dovetailed channel, which can be bonded to floor surfaces using Schluter -KERDI-FIX, epoxy resin, silicone, thin-set mortar, etc. A 3/8" (10 mm) radius cove section forms the visible surface and prevents the accumulation of dirt, making cleaning simple. DILEX- AHKA prevents surface water penetration and meets the maintenance and hygienic requirements of commercial kitchens, bathrooms, and food-processing plants, or any tiled environment where a sanitary cove base is desired. DILEX-AHKA integrates with the DILEX-AHK and Schluter -RONDEC profiles at 90 inside and outside vertical wall corners, respectively. for DILEX-AHKA include 90 and 135 inside and outside corners, and end caps Schluter -DILEX-EHK features trapezoid-perforated anchoring legs, made of stainless steel, which are secured in the mortar bond coat, and a stainless steel cove section that forms the visible surface. The profile s 23/32" (18.5 mm) radius prevents the accumulation of dirt and makes cleaning simple. The profile separates tile fields that meet at inside corners where limited movement is expected Schluter -DILEX-HKS features a soft, thermoplastic rubber movement zone that is attached to the profile via rigid rubber grip bars to absorb larger movements at floor/wall transitions and at inside wall corners. DILEX-EHK and DILEX-HKS prevent surface water penetration and meet the maintenance and hygienic requirements of commercial kitchens, bathrooms, foodprocessing plants, and hospitals, or any tiled environment where a sanitary cove base is desired. for both DILEX-EHK and DILEX-HKS include: inside and outside corners, connectors, and end caps. 135 inside and outside corners are available for DILEX-EHK only. Material Properties and Areas of Application DILEX profiles are resistant to most chemicals encountered in tiled environments. In special cases, the suitability of a proposed type of profile must be verified based on the anticipated chemical, mechanical, and/or other stresses. Exceptions and special considerations are listed below: Stainless steel profiles are roll-formed, resulting in a slightly different contour from those made of extruded brass or. Stainless steel can sustain high mechanical stresses and is particularly well suited for applications requiring resistance against chemicals and acids; for example in the food industry, breweries, dairies, commercial kitchens, and hospitals, as well as in residential applications. Typically, the profiles are formed using stainless steel 304 ( = V2A). For more severe chemical exposure, such as de-icing salts and chemicals used in swimming pools, we recommend the use of stainless steel 316 L ( = V4A), which offers even higher corrosion resistance than the 304. Even stainless steel cannot withstand all chemical exposures, such as hydrochloric acid, hydrofluoric acid or certain chlorine, chloride and brine concentrations. Aluminum profiles must be tested to verify their suitability if chemical stresses are anticipated. Cementitious materials, in conjunction with moisture, become alkaline. Since is sensitive to alkaline substances, exposure to the alkali (depending on the concentration and duration of exposure) may result in corrosion ( hydroxide formation). Therefore, it is important to remove mortar or grout residue from visible surfaces. In addition, ensure that the profile is solidly embedded in the setting material and that all cavities are filled to prevent the collection of alkaline water. Anodized profiles feature an layer that retains a uniform appearance during normal use. The surface, however, is susceptible to scratching and wear and may be damaged by grout or setting material. Therefore, these materials must be removed immediately. Otherwise, the description regarding applies. Tuscan color-coated is pretreated (chromated) that is color-coated with a polyurethane powder coat. The coating is color-stable, UV-resistant, and suitable for exterior use. Protect the profile against abrasion or scratching. Thermoplastic rubber inserts are highly resistant to chemicals and can withstand chemical stresses typically encountered in tile coverings. The insert is resistant to aging, weather, UV-rays, and ozone within a temperature range of -76 F (-60 C) to 212 F (100 C). Thermoplastic elastomers can be connected by welding if profiles are joined to produce longer lengths. CPE movement zones contain no softeners, are UV-resistant, and can withstand exposure to weather. They are resistant to fungi and bacteria and are, therefore, suitable for use around food. The CPE material is also resistant to a number of acids, alkalis, oils, greases, and solvents. PVC movement zones are UV-resistant, though not permanently color-stable, in exterior applications. PVC profiles are made of pre-colored, rigid PVC that resists bending or scratching. The material is UV-resistant, though not permanently color-stable, in exterior applications. Installation Mortar Bed Joint Profiles MOP, and MP/MPV 1. Select profile height according to the height of the assembly. Note: for DILEX-MP, attach necessary snap-on extensions (-MPV). 2. Set the profile flush against the edge area of an already completed field. The profile must be completely embedded laterally. 3. Install tiles for the adjacent field flush to the profile surface. The profile must be completely embedded laterally. 4. Fill the remaining joint between the profile and the covering completely with grout or setting material. Installation note on joint repair: Prepare the joint s width and depth appropriately and insert profile into joint. Fill joint space between profile and covering completely with grout, epoxy, or thin-set mortar. Surface Joint Profiles EZ 1. Select DILEX-EZ 6 or DILEX-EZ 9 according to tile thickness. For tile thicknesses greater than 11/32" (9 mm), DILEX-EZ 9 must be backbuttered with thin-set mortar. 2. Set tiles up to the point where DILEX-EZ is to be installed. Apply thin-set mortar to tile edges. The profile must align directly with movement joints in the substrate below. Press the profile against the tile edge and flush with the tile surface so that the ribbed, hourglass-shaped section is completely embedded in the mortar. 5

6 3. For the next row of tiles, apply thin-set mortar to the side wall of the DILEX-EZ profile already in place; then press the tiles against the profile so that they are flush with the profile surface. 4. DILEX-EZ may be installed with or without a small joint to the adjacent tile. BWS, BWB, EDP, KSN, and AKWS 1. Select profile according to tile thickness. 2. Using a notched trowel, apply thin-set mortar over the area where the profile is to be placed. The profile must align directly with movement joints in the substrate below. 3. Press the perforated anchoring legs of the profile into the mortar and align. 4. Trowel additional thin-set mortar over the perforated anchoring legs to ensure full coverage and support of the tile edges. 5. Solidly embed the tiles so that the tiled surface is flush with the top of the profile; the profile should not be higher than the tiled surface, but rather up to approx. 1/32" (1 mm) lower. 6. A joint of approximately 1/16" - 1/8" (1.5-3 mm) should be left between the tile and the profile. 7. Fill the joint completely with grout or setting material. Expansion Joint Profiles BT 1. Select profile according to tile thickness. 2. Using a notched trowel, apply thin-set mortar over the area where the profile is to be placed. The profile must align directly with movement joints in the substrate below. 3. Press the perforated anchoring legs of the profile into the mortar and align. 4. Trowel additional thin-set mortar over the perforated anchoring legs to ensure full coverage and support of the tile edges. 5. Solidly embed the tiles so that the tiled surface is flush with the top of the profile; the profile should not be higher than the tiled surface, but rather up to approx. 1/32" (1 mm) lower. 6. For DILEX-BT, the tile is set to the integrated joint spacer, which ensures a uniform joint of 1/16" - 1/8" (1.5-3 mm). 7. Fill the joint completely with grout or setting material; remove the protective foil from DILEX-BT. 8. The installation of the profile on wall and ceiling surfaces is essentially equivalent to floor applications. 9. DILEX-BTS can be inserted into existing joint spaces. The joints must be at least 1-3/4" (44 mm) wide and 3/8" (10 mm) deep. The lateral anchoring legs are adhered to the existing covering with a 6 suitable adhesive (e.g., epoxy resin) or mechanically fastened to the covering with the appropriate screws. Perimeter Joint Profiles AS 1. Thoroughly clean the contact area on adjoining fixtures where DILEX-AS will be positioned. 2. Using a notched trowel, apply the thin-set mortar over the area where the trapezoid-perforated anchoring leg will be placed. 3. Remove the paper from the selfadhesive tape. Apply Schluter - KERDI-FIX or silicone sealant parallel and adjacent to self-adhesive tape. Press the profile with self-adhesive tape against the fixture in such a way that the perforated anchoring leg can also be pressed into the applied thin-set mortar. 4. Install inside corners and end caps with KERDI-FIX or silicone prior to setting tiles. 5. Trowel additional thin-set mortar over the perforated anchoring leg to ensure full coverage. 6. A joint of approx. 1/16" - 1/8" (1.5-3 mm) should be left between the tile and the profile. 7. Fill the joint completely with grout or setting material. BWA and KSA 1. Select profile according to tile thickness. 2. Using a notched trowel, apply thin-set mortar over the area where the profile is to be placed. 3. If necessary, fill the dovetailed channel of DILEX-BWA with KERDI-FIX, epoxy resin, silicone, or similar to adhere the profile to the existing structure. Remove film from self-adhesive backing strip on DILEX-KSA. 4. Press the perforated anchoring leg of the profile into the mortar and adjust it securely against the existing building elements. 5. Trowel additional thin-set mortar over the perforated anchoring leg to ensure full coverage and support of the tile edges. 6. Solidly embed the tiles and align flush with the top of the profile. 7. A joint of approx. 1/16" - 1/8" (1.5-3 mm) should be left between the tile and the profile. 8. Fill the joint completely with grout or setting material. Cove-shaped Profiles EKE, HKW, HK, HKU, PHK, AHK, AHKA, EHK, and HKS 1. Select profile according to tile thickness. Note: For DILEX-HK and DILEX-EKE, profile height, U, must allow insertion of the tile into the tile pocket; for example, select U 12 for a tile thickness between approx. 3/8" (10 mm) and 7/16" (11 mm). DILEX-HKU with 3/8" (10 mm) radius may be used with 1/4" (6 mm) and thicker tiles. DILEX- HKU with 1-13/32" (36 mm) radius may be used with 5/16" (8 mm) and thicker tiles. 2. Using a notched trowel, apply thinset mortar over the area where the trapezoid-perforated anchoring legs will be placed. Note: If necessary, fill the dovetailed channel of DILEX-AHKA with KERDI- FIX, epoxy resin, silicone, thin-set mortar or similar to adhere the profile to the existing floor surface. Note: When using thicker tiles with DILEX-HKU, apply additional mortar behind the anchoring leg. 3. Press the perforated anchoring leg(s) of the profile into the mortar. Note: Install inside and outside corners, connectors, and end caps prior to setting tile. The use of thin-set mortar or similar may be required to achieve a proper fit. DILEX-EHK/-HKS/-HKU accessories are applied using a permanently elastic, waterproof adhesive (e.g., KERDI- FIX or silicone). Prior to application, any contact-inhibiting substances (e.g., grease, etc.) must be removed. The connectors should overlap the profiles by at least 3/8" (10 mm). 4. Trowel additional thin-set mortar where the tiles are to be installed. 5. Solidly embed the tiles, ensuring full coverage and support of the tile edges, and align flush with the top of the profile, leaving a joint of approximately 1/16" 1/8" (1.5-3 mm) between the tile and the profile. Note: For DILEX- HK and DILEX- EKE, insert floor tile into the tile pocket. For DILEX- AHK, set tile to the integrated joint spacer, which ensures a uniform joint of 1/16" 1/8" (1.5 3 mm). 6. Fill the joints completely with grout or setting material. Maintenance DILEX profiles require no special maintenance or care and are resistant to mold and fungi. Clean profile using common household cleaning agents. Stainless steel surfaces exposed to the environment or aggressive substances should be cleaned periodically using a

7 mild household cleaner. Regular cleaning maintains the neat appearance of stainless steel and reduces the risk of corrosion. All cleaning agents must be free of hydrochloric acid, hydrofluoric acid, and chlorides. Stainless steel surfaces develop a sheen when treated with a chromepolishing agent. Oxidation films on exposed solid brass or can be removed by using a conventional polishing agent, but will form again. In the case of and Tuscan color-coated do not use abrasive cleaning agents. The thermoplastic rubber inserts in DILEX-KSN/-KSA/-HKS are replaceable, with the exception of -EKSB. Product Item Numbers Mortar Bed Joint Profiles MOP 5/16" - 8 mm 4.4 Schluter -DILEX-MOP /8 MOP MOP /8 MOP 65 Note: Available in only 5/16" - 8 mm 4.3 Schluter -DILEX-MP /8 MP 35 color* ZR Brick red S Black To complete the item number, add the color code (e.g., MP 35 ). MP MPV 4.3 Schluter -DILEX-MPV 15-9/16 MPV MPV 25 Surface Joint Profiles Residential to Medium-Duty Commercial Applications 9/32" - 7 mm 4.1 Schluter -DILEX-EZ 6 6-1/4 EZ color* Schluter -DILEX-EZ /32 EZ color* 9 C Yellow To complete the item number, add the color code (e.g., EZ M/ 6). M/ = Brass inlay / C/C = Chrome inlay / yellow 7

8 3/16" - 5 mm 2-3/16" - 56 mm 4.7 Schluter -DILEX-BWS 4.5-3/16 BWS 45 color* 6-1/4 BWS 60 color* 8-5/16 BWS 80 color* 9-11/32 BWS 90 color* 10-3/8 BWS 100 color* 11-7/16 BWS 110 color* /2 BWS 125 color* BW Bright white P SP Sand pebble S Black To complete the item number, add the color code (e.g., BWS 80 ). 3/8" - 10 mm 4.6 Schluter -DILEX-BWB 6-1/4 BWB 60 color* 8-5/16 BWB 80 color* 10-3/8 BWB 100 color* /2 BWB 125 color* 15-9/16 BWB 150 ( only) 20-3/4 BWB 200 ( only) 2-3/16" - 56 mm BW Bright white P SP Sand pebble To complete the item number, add the color code (e.g., BWB 80 ). BWB 60 is not available in sand pebble (SP) S Black 1/4" - 6 mm 2-5/16" - 58 mm 4.18 Schluter -DILEX-AKWS 8-5/16 AKWS 80 color* 9-11/32 AKWS 90 color* 10-3/8 AKWS 100 color* 11-7/16 AKWS 110 color* /2 AKWS 125 color* 14-17/32 AKWS 140 color* 16-5/8 AKWS 160 color* 21-13/16 AKWS 210 color* Length supplied: 8'2-1/2" 2.5 m SP Sand pebble S Black P To complete the item number, add the color code (e.g., AKWS 80 ). Heavy-duty Commercial Applications 15/32" - 12 mm 4.16 Schluter -DILEX-EDP 8-5/16 EDP /32 EDP /8 EDP /16 EDP /2 EDP /32 EDP /8 EDP /32 EDP /16 EDP EDP /16 EDP 300 8

9 Aluminum 7/16" - 11 mm 2-5/16" - 58 mm Stainless steel 7/16" - 11 mm 2-11/16" - 68 mm 4.8 Schluter -DILEX-KSN Stainless steel 304 ( = V2A) (E) Aluminum 8-5/16 EKSN 80 color* AKSN 80 color* 10-3/8 EKSN 100 color* AKSN 100 color* 11-7/16 EKSN 110 color* AKSN 110 color* /2 EKSN 125 color* AKSN 125 color* 14-17/32 EKSN 140 color* AKSN 140 color* 16-5/8 EKSN 160 color* AKSN 160 color* /32 EKSN 185 color* /16 EKSN 210 color* AKSN 210 color* 25-1 EKSN 250 color* /16 EKSN 300 color* - (A) Rubber insert replacement KSE / color* SP Sand pebble S Black P Note: DILEX-KSN is also available with stainless steel 316 L ( = V4A) anchoring legs. To complete the item number, add the color code (e.g., EKSN 160 P). 1/4" - 6 mm 2-1/4" - 56 mm Schluter -DILEX-EKSB Stainless steel 304 ( = V2A) (E) 2.5-3/32 EKSB 25 color* 4.5-3/16 EKSB 45 color* 6-1/4 EKSB 60 color* P S Black To complete the item number, add the color code (e.g., EKSB 60 ). Note: DILEX-EKSB is also available with stainless steel 316 L ( = V4A) anchoring legs. 9

10 4.20 Schluter -DILEX-BT 1/2" mm 4.20 Schluter -DILEX-BTO Satin (AE) 1-3/16" - 30 mm Satin (AE) 1-19/32" - 40 mm 1-3/32"- 1-3/16"- 28 mm 30 mm 3/16" - 5 mm 8-5/16 AEBT /8 AEBT /2 AEBT /16 AEBT /16 AEBT /4 AEBT /16 AEBT 80 / O /8 AEBT 100 / O /2 AEBT 125 / O /16 AEBT 150 / O /16 AEBT 175 / O /4 AEBT 200 / O 125 4" mm 4.20 Schluter -DILEX-BTS 1-7/16"- 1-3/16"- 36 mm 30 mm 3/16" - 5 mm mm - po. Satin (AE) 10-3/8 AEBTS 100 1/2" mm 3/8" - 10 mm Schluter -DILEX-BT/OT Satin (AE) /2 AEBTO 125 3/16" - 5 mm 1-3/16" - 30 mm Schluter -DILEX-BT/-MT Satin (AE) 3/16" - 5 mm 4.20 Schluter -DILEX-BT/VT Satin (AE) /16 AEBT 30 MT 8-5/16 AEVT /8 AEVT /2 AEVT /16 AEVT /16 AEVT /4 AEVT

11 Perimeter Joint Profiles 1-1/8" - 29 mm 11/32" - 9 mm 4.10 Schluter -DILEX-AS 9-11/32 AS 20 BW Color Code BW Bright white End cap (right) EKR/AS 20 BW End cap (left) EKL/AS 20 BW Inside corner I/AS 20 BW 2 inside corners + EKI/AS 20 BW 1 right end cap + 1 left end cap 3/4" - 20 mm End cap Inside Corner Note: Suitable for tiles 3/16" to 3/8" (4-10 mm) thick. 3/16" - 5 mm 1-3/16" - 30 mm 4.9 Schluter -DILEX-BWA 4.5-3/16 BWA 45 + color* 6-1/4 BWA 60 + color* 8-5/16 BWA 80 + color* 10-3/8 BWA color* /2 BWA color* BW Bright white P SP Sand pebble S Black To complete the item number, add the color code (e.g., BWA 80 ). BWA 45 is not available in sand pebble (SP). 3/8" - 10 mm 3/8" - 10 mm 4.9 Schluter -DILEX-KSA 11-7/16 EKSA 110 color* - AKSA 110 color* /2 EKSA 125 color* EKSA 125 color* / V4A AKSA 125 color* 14-17/32 EKSA 140 color* EKSA 140 color* / V4A AKSA 140 color* 16-5/8 EKSA 160 color* EKSA 160 color* / V4A /32 EKSA 185 color* /16 EKSA 210 color* EKSA 250 color* /16 EKSA 300 color* - - Stainless Stainless Aluminum Rubber insert replacement steel 304 steel 316 L ( = V2A) ( = V4A) AKSA (E) (EV4A) (A) P 8-5/16 EKSA 80 color* EKSA 80 color* / V4A AKSA 80 color* 10-3/8 EKSA 100 color* EKSA 100 color* / V4A AKSA 100 color* EKSA S Black To complete the item number, add the color code (e.g., EKSA 100 ). KSAE / color* Cove-shaped Profiles = O 3/16" - 5 mm = U 4.13 Schluter -DILEX-EKE EKE U 8 / O 7 color* EKE U 9 / O 8 color* EKE U 11 / O 10 color* EKE U 13 / O 12 color* EKE U 15 / O 14 color* BW Bright white P SP Sand pebble S Black To complete the item number, add the color code (e.g., EKE U8/O7 BW). U: 5/16" = 8 mm 11/32" = 9 mm 7/16" = 11 mm 33/64" = 13 mm 9/16" = 15 mm O: 9/32" = 7 mm 5/16" = 8 mm 3/8" = 10 mm 1/2" = 12 mm 17/32" = 14 mm 11

12 = O 4.12 Schluter -DILEX-HKW HKW U 7 / O 7 color* HKW U 9 / O 9 color* HKW U 11 / O 11 color* Outside corner Inside corner (2-way) Inside corner (3-way) End cap A / HKW / color* I / HKW 2 R18 color* I / HKW 3 R18 color* E / HKW / ( only) r = 11/16" - 18 mm = U U: 9/32" = 7 mm 11/32" = 9 mm 7/16" = 11 mm O: 9/32" = 7 mm 11/32" = 9 mm 7/16" = 11 mm BW Bright white P To complete the item number, add the color code (e.g., HKW U 9 / O 9 ). Outside Corner Inside Corner (2-way) Inside Corner (3-way) End Cap = O r = 11/16" - 18 mm = U 4.11 Schluter -DILEX-HK HK U 12 / O 9 color* U: 1/2" = 12 mm O: 11/32" = 9 mm Outside corner Inside corner (2-way) Inside corner (3-way) Connector End cap (left) End cap (right) A / HK / color* I / HK 2 R18 color* I / HK 3 R18 color* V / HK EL / HK / ( only) ER / HK / ( only) BW Bright white To complete the item number, add the color code (e.g., HK U 12 / O 9 BW). Outside Corner Inside Corner (2-way) Inside Corner (3-way) Connector End Cap 12

13 5/8" - 16 mm 5/16" - 8 mm r = 3/8" - 10 mm 3/4" mm 5/16" - 8 mm 4.22 Schluter -DILEX-HKU (10 mm - 3/8" radius) Stainless steel 304 ( = V2A) (E) Brushed stainless steel 304 ( = V2A) (EB) Stainless steel 316L ( = V4A) (EV4A) 10-3/8 HKUR 10 E HKUR 10 EB HKUR 10 E / V4A Outside Corner Inside Corner (2- or 3-way) Connector Outside corner 90º EQ / HKUR 10 finish* Outside corner 135º E135 / HKUR 10 finish* Inside corner 90º I / HKU 3 R 10 finish* Inside corner 135º I135 / HKUR 10 finish* Connector V / HKUR 10 finish* * To complete the item number, add the finish code (e.g., EQ / HKUR 10 E). 11 mm - 7/16" 25 mm - 1" r = 36 mm 1-13/32" 48.6 mm /32" 11 mm - 7/16" 4.22 Schluter -DILEX-HKU (36 mm /32" radius) Stainless steel 304 ( = V2A) (E) /32 HKUR 36 E Outside corner 90º Inside corner 90º Connector End Cap E / HKUR 36 E I / HKU 3 R E V / HKUR 36 E EK / HKUR 36 E 13

14 r = 3/8" - 10 mm 4.21 Schluter -DILEX-AHK Satin (AE) Polished chrome (AC) Brushed chrome (ACB) Satin nickel (AT) Polished nickel (AT) 8-5/16 AHK 1S 80 AE AHK 1S 80 AC AHK 1S 80 ACB AHK 1S 80 AT AHK 1S 80 AT 10-3/8 AHK 1S 100 AE AHK 1S 100 AC AHK 1S 100 ACB AHK 1S 100 AT AHK 1S 100 AT /2 AHK 1S 125 AE AHK 1S 125 AC AHK 1S 125 ACB AHK 1S 125 AT AHK 1S 125 AT 15-9/ AHK 1S 150 AT - Brushed nickel (ATB) Satin copper/bronze (AK) Polished copper/bronze (AK) Brushed copper/bronze (AKB) Satin brass (AM) 8-5/16 AHK 1S 80 ATB AHK 1S 80 AK AHK 1S 80 AK AHK 1S 80 AKB AHK 1S 80 AM 10-3/8 AHK 1S 100 ATB AHK 1S 100 AK AHK 1S 100 AK AHK 1S 100 AKB AHK 1S 100 AM /2 AHK 1S 125 ATB AHK 1S 125 AK AHK 1S 125 AK AHK 1S 125 AKB AHK 1S 125 AM Polished brass (AM) Brushed brass (AMB) Brushed graphite (ARB) 8-5/16 AHK 1S 80 AM AHK 1S 80 AMB AHK 1S 80 ARB 10-3/8 AHK 1S 100 AM AHK 1S 100 AMB AHK 1S 100 ARB /2 AHK 1S 125 AM AHK 1S 125 AMB AHK 1S 125 ARB 15-9/ AHK 1S 150 ARB Outside Corner Tuscan color-coated (TSB) Tuscan bronze color-coated (TSOB) Tuscan pewter color-coated (TS) 8-5/16 AHK 1S 80 TSB AHK 1S 80 TSOB AHK 1S 80 TS 10-3/8 AHK 1S 100 TSB AHK 1S 100 TSOB AHK 1S 100 TS /2 AHK 1S 125 TSB AHK 1S 125 TSOB AHK 1S 125 TS Outside Corner (QUADEC) Inside Corner (2- or 3-way) Outside corner, 90º Outside corner, 90º (to match Schluter -QUADEC profile) Outside corner, 135º Inside corner, 90º Inside corner, 135º Connector End cap E 90 / AHK 1S / finish* E 90 Q / AHK 1S / finish* E 135 / AHK 1S / finish* I 90 / AHK 1S / finish* I 135 / AHK 1S / finish* V / AHK E / AHK 1S / finish* Connector End cap * To complete the item number, add the finish code (e.g., E 90 / AHK 1S / AE). Note: E 90 Q (outside corner piece to match QUADEC) is only available in AE, AC, AT, TSB, TSOB, and TS finishes. 14

15 r = 3/8" - 10 mm 4.22 Schluter -DILEX-AHKA Satin (AE) Brushed chrome (ACB) Satin nickel (AT) Brushed nickel (ATB) 8-5/16 AHKA 80 AE AHKA 80 ACB AHKA 80 AT AHKA 80 ATB 10-3/8 AHKA 100 AE AHKA 100 ACB AHKA 100 AT AHKA 100 ATB /2 AHKA 125 AE AHKA 125 ACB AHKA 125 AT AHKA 125 ATB 15-9/16 AHKA 150 AE AHKA 150 ACB AHKA 150 AT AHKA 150 ATB Outside corner, 90º Outside corner, 135º Inside corner, 90º Inside corner, 135º End cap (Left) End cap (Right) E 90 / AHKA / finish* E 135 / AHKA / finish* I 90 / AHKA / finish* I 135 / AHKA / finish* EL / AHKA / finish* ER / AHKA / finish* * To complete the item number, add the finish code (e.g., E 90 / AHKA / AE). r = 3/8" - 10 mm 4.21 Schluter -DILEX-PHK 8-5/16 PHK 1S 80 + color* 10-3/8 PHK 1S color* /2 PHK 1S color* Outside corner, 90º Outside corner, 135º Inside corner, 90º Inside corner, 135º Connector End cap Outside corner Inside Corner Connector BW Bright white W White P SP Sand pebble BH Bahama * To complete the item number, add the color code (e.g., PHK 1S 80 BW). E 90 / PHK 1S + color* E 135 / PHK 1S + color* I 90 / PHK 1S + color* I 135 / PHK 1S + color* V / PHK E / PHK 1S + color* End cap 4.15 Schluter -DILEX-EHK Outside Corner Inside Corner (2-way) = O r = 23/32" mm = U Stainless steel 304 ( V2A) (E) Stainless steel 316 L ( V4A) (EV4A) Brushed stainless steel 304 ( = V2A) (EB) EHK U 7 / O 7 EHK U 7 / O 7 / V4A EBHK U 7 / O 7 EHK U 9 / O 9 EHK U 9 / O 9 / V4A EBHK U 9 / O 9 EHK U 11 / O 11 EHK U 11 / O 11 / V4A EBHK U 11 / O 11 - EHK U 16 / O 16 / V4A - Inside Corner (3-way) Connector U: 9/32" = 7 mm 11/32" = 9 mm 7/16" = 11 mm 5/8" = 16 mm O: 9/32" = 7 mm 11/32" = 9 mm 7/16" = 11 mm 5/8" = 16 mm Stainless steel 304 ( V2A) (E) Brushed stainless steel 304 ( = V2A) (EB) Outside corner A / EHK 2 R18 A / EBHK 2 R18 Outside corner, 135º E 135 / EHK 2 R18 E 135 / EB HK 2 R18 Inside corner (2-way) I / EHK 2 R18 I / EBHK 2 R18 Inside corner (3-way) I / EHK 3 R18 I / EBHK 3 R18 Inside corner, 135º I 135 / EHK 2 R18 I 135 / EB HK 2 R18 Connector V / EHK V / EBHK End cap E / HKW / * E / HKW / * *Available in PVC only End Cap 15

16 = O r = 23/32" mm = U 4.15 Schluter -DILEX-HKS Stainless steel 304 ( V2A) (E) U = floor or wall, O = wall HKS V2A U 8 / O 7 + color* HKS V2A U 10 / O 7 + color* HKS V2A U 12 / O 7 + color* HKS V2A U 14 / O 7 + color* HKS V2A U 16 / O 7 + color* HKS V2A U 18 / O 7 + color* HKS V2A U 21 / O 7 + color* HKS V2A U 25 / O 7 + color* HKS V2A U 30 / O 7 + color* HKS V2A U 8 / O 9 + color* HKS V2A U 10 / O 9 + color* HKS V2A U 12 / O 9 + color* HKS V2A U 14 / O 9 + color* HKS V2A U 16 / O 9 + color* HKS V2A U 18 / O 9 + color* HKS V2A U 21 / O 9 + color* HKS V2A U 25 / O 9 + color* HKS V2A U 30 / O 9 + color* HKS V2A U 8 / O 11 + color* HKS V2A U 10 / O 11 + color* HKS V2A U 12 / O 11 + color* HKS V2A U 14 / O 11 + color* HKS V2A U 16 / O 11 + color* HKS V2A U 18 / O 11 + color* HKS V2A U 21 / O 11 + color* HKS V2A U 25 / O 11 + color* HKS V2A U 30 / O 11 + color* Outside corner Inside corner (2-way) Inside corner (3-way) Connector End cap Note: DILEX-HKS is also available in stainless steel 316 L ( = V4A). P S Black To complete the item number, add the color code (e.g., HKS V2A U 18 / O 7 ). A / EHK 2 R18 I / EHK 2 R18 I / EHK 3 R18 V / EHK E / HKW / ( only) U: 5/16" = 8 mm 3/8" = 10 mm 15/32" = 12 mm 17/32" = 14 mm 5/8" = 16 mm 23/32" = 18 mm 13/16" = 21 mm 1" = 25 mm 1-3/16" = 30 mm O: 9/32" = 7 mm 11/32" = 9 mm 7/16" = 11 mm Outside Corner Inside Corner (2-way) Inside Corner (3-way) Connector End Cap Note: 3-way corners are to be used with DILEX-EHK on the vertical. 16

17 17

18

19 Schluter -Systems Movement Joints and Cove-shaped Profiles 5-Year Limited Warranty COVERAE AND CONDITIONS: Subject to the conditions and limitations as stated hereinafter, Schluter-Systems* warrants that Schluter -Systems Movement Joints and Cove-Shaped Profiles (the Products )** will be free from manufacturing defects for a period of five (5) years from the date of purchase and only when the Products are used and installed in accordance with the terms and conditions of the Schluter -Systems Movement Joints and Cove-Shaped Profiles Technical Data Sheet and industry standard guidelines that are not in conflict with the data sheet in effect at the time of installation. It is the responsibility of the owner/builder/installer to ensure the suitability of all building materials and all associated building materials for the owner s intended use. Visual defects or nonconformities apparent prior to installation are not covered by this warranty. Further, this warranty does not cover normal wear and tear or other damage (e.g., scratches, discoloration, fading, etc.) caused by impacts or accidents. Consumable parts of Products are warranted, at the time of sale, only against defects in workmanship or materials that prevent their use. Consumable parts are goods reasonably expected to be used up or damaged during normal use, including but not limited to replaceable movement zones. It is recommended that the owner consult an experienced and professional installer. RESOLUTION: If the Products fail to meet this warranty, then the owner s exclusive remedy and the sole obligation of Schluter-Systems, at its election, shall be to a) reinstall or replace the failed portion of the tile assembly or b) pay an amount not to exceed the original square foot cost of the installation of the tile assembly verified to be defective. Tile assembly is defined to include all Schluter -Systems Movement Joints and Cove-Shaped Profiles, nonreusable tile surfaces, and the appropriate setting and grouting materials. Further, due to conditions beyond the control of Schluter-Systems (e.g., color and shade availability, discontinuation, normal wear and tear), Schluter-Systems cannot guarantee or warrant an exact match to the specific tile, stone, or other flooring materials used in the installation. In such events, substantially similar materials may be substituted. DISCLAIMER: THERE ARE NO WARRANTIES BEYOND THIS EXPRESSED WARRANTY AS STATED ABOVE. ALL OTHER WARRANTIES, REPRESENTATIONS OR CONDITIONS, EXPRESSED OR IMPLIED, ARE DISCLAIMED AND EXCLUDED, INCLUDIN WARRANTIES, REPRESENTATIONS OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARISIN BY STATUTE OR OTHERWISE BY LAW OR FROM A COURSE OF DEALIN OR USAE OF TRADE. SCHLUTER-SYSTEMS EXCLUDES AND IN NO EVENT SHALL HAVE ANY LIABILITY FOR LOST PROFITS OR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, OR CONSEQUENTIAL DAMAES, ARISIN OUT OF OR OTHERWISE CONNECTED TO FAILURE OF THE PRODUCTS OR FLOORIN SYSTEM OF WHICH THEY ARE PART, NOR MISUSE OF THE PRODUCTS OR FLOORIN SYSTEM, REARDLESS OF ANY STRICT LIABILITY, ACTIVE OR PASSIVE NELIENCE OF SCHLUTER-SYSTEMS, AND REARDLESS OF THE LEAL THEORY (CONTRACT OR TORT OR EXTRA-CONTRACTUAL OR OTHER), NOR FROM ACTS OF WAR, TERRORISM, FAULTY AND NELIENT PENETRATION OF THE SYSTEM, FIRES, EXPLOSIONS, ACTS OF OD, INTENTIONAL ACTS OF DESTRUCTION OR ANY LOSSES DUE TO STRUCTURAL FAILURE OR OTHER CAUSES UNRELATED TO THE PRODUCTS OR DELAYS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAES. THIS WARRANTY IS IVEN IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED. THE REMEDIES CONTAINED HEREIN ARE THE ONLY REMEDIES AVAILABLE FOR BREACH OF THIS WARRANTY. THIS LIMITED WARRANTY IVES YOU SPECIFIC LEAL RIHTS, SOME STATES AND PROVINCES DO NOT ALLOW DISCLAIMERS OR OTHER RESTRICTIONS OF IMPLIED WARRANTIES SO SOME OF THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. TRANSFERABILITY: This Limited Warranty extends ONLY to the original end user (defined as original intended owner and user of the property/unit in which the installation is incorporated - herein referred to as Owner ) and is not transferable or assignable, unless approved in writing by the Technical Director or an Officer of Schluter-Systems or otherwise prohibited by specific state or provincial law. MODIFICATIONS TO WARRANTY: No changes or modification of any terms or conditions of this warranty are allowed unless authorized by written agreement and signed by the Technical Director or an Officer of Schluter-Systems. EFFECTIVE DATE: This warranty shall supersede and replace any and all prior oral or written warranties, agreements, or other such representations made by or on behalf of Schluter-Systems relative to the Products or the application of the Products and shall apply to any installation occurring on or after January 1, CLAIMS ON THIS LIMITED WARRANTY: To make a claim under this Limited Warranty, the owner must provide Schluter-Systems with written notice within 30 days of any alleged defect in the Products covered by this Limited Warranty, together with date and proof of purchase of the Products, proof of the costs of the original installation and name and address of all installers, failing which this Limited Warranty shall be of no legal effect. Schluter-Systems reserves the right at its election and as a condition of this Limited Warranty to inspect the alleged failed and defective condition. All U.S. Claims shall be sent to: All Canadian Claims shall be sent to: Schluter Systems L.P. Schluter Systems (Canada), Inc. Attn: Warranty Claims Dept. Attn: Warranty Claims Dept. 194 Pleasant Ridge Road chemin Ste-Marie Plattsburgh, NY Ste-Anne-de-Bellevue, QC H9X 3Y8 *For the purpose of this warranty Schluter Systems, L.P. shall provide the warranty for all products for end users located in the United States, and Schluter Systems (Canada) Inc. shall provided provide the warranty for all products for end users located in Canada. This warranty is limited to sales of the Products made in and intended for use in the United States and Canada. **Schluter -Systems Movement Joints and Cove-Shaped Profiles (the Products ): The Products are defined to include all Schluter -Systems Movement Joints and Cove-Shaped profiles referred to in the Schluter -Systems Movement Joints and Cove-Shaped Profiles Data Sheet.