MEP Design Standards & Equip Cuts NYP BEST PRACTICES. Presentation for GC/CM Retreat 2014

Transcription

1 1 MEP Design Standards & Equip Cuts NYP BEST PRACTICES Presentation for GC/CM Retreat 2014

2 We Put Patients First Agenda 2 Disclaimer Consultant Engineer & Commissioning Agent May 2012 Edition NYP Revised Requirements 2014 NYC Building Code Highlights Building Resiliency Code Highlights Equipment Selection Process Locating the Design Standards on the Portal Updating and Maintaining

3 3 3 DISCLAIMER The purpose of this document is to provide the design engineer with the guidelines for HVAC, electrical, plumbing, fire protection, fire alarm, nurse call, commissioning and controls, specified herein on NYPH campuses. This does not substitute the design engineer s specifications for each project but provides the basis of the standards, which the design engineer shall follow. The final responsibility for the design of the specific project resides with the design engineer of record.

4 Consultant Engineer and Cx Responsibilities 4 FDC-E FO FDC Campus Master Engineer (One per Campus) Commissioning Agent (Two per Campus) Project Design Engineer (Individual Project) Tasks Capacity Police - Assesses the capacity impact of project designs to existing MEP systems Focused on Strategic Planning and Design Criteria for MER s and Risers. Updating and maintaining existing MEP riser and distribution documents Specifies Capacities and Performance Requirements Funded by Infrastructure Program Management Project Police Focused on MEP Performance related to project installation Reviews Basis of Design Requirements with OFO and Project Design Engineer O&M, equipment warranty, start up and preventative maintenance to insure proper project close outs. Provide Measurement and Verification to Campus Engineer Funded by Specific Project Engineer of Record - Focused on design of Individual Project Provides load information to OFD-E and Campus Engineer Provides Basis of Design for project based on Owner Requirements for review by Commissioning Agent and OFO Funded by Specific Project

5 MASTERFORMAT divisions to latest CSI nomenclature: 5 NYP Design Specifications May 2012 Edition Mechanical Division 15 to Division 23 Plumbing Division 15 to Division 22 Fire Protection Division 15 to Division 21 Electrical Division 16 to Division 26 Added Sections include: Equipment Cuts Commissioning/Energy Compliance Guidelines Building Specific Checklist Updated to meet the latest 2008 NYC Building Code & 2010 FGI requirements.

6 Mechanical Division 23 6 NYP Design Specifications Update 2014 Highlights NYP Requirements All air systems requiring humidification must include clean steam generators Standardized controls packages for mechanical equipment Electrical Division 26 Requirements for GFI Circuit Breakers to be installed in lieu of GFI outlets in wet locations Plumbing Division 22 Revisions to the Plumbing Fixtures Review and update to meet the latest 2014 NYC Building Code & 2014 FGI requirements.

7 Mechanical Division 23 7 NYP Design Specifications Update 2014 Highlights 2014 NYC Building Code Wind bracing requirements for roof top equipment upgraded Permits utilizing 1968 Code fire and smoke damper requirements in 1968 Code or prior compliant buildings * Permits high temperature water systems similar to high pressure steam systems New requirements for high pressure gas piping systems and installations Clarifies CO detection requirements for Class E, I2 & I4 occupancies *must comply with the most stringent code

8 Plumbing Division 23 New plumbing fixture calculations for new construction 8 NYP Design Specifications Update 2014 Highlights 2014 NYC Building Code Allows plumbing fixture calculations in prior code buildings to be based on 1968 Building Code utilizing 1968 occupancy load calculations Back flow preventers on sewage mains (Resiliency) Fire Protection Division 22 Enhanced fire protection, smoke detection and life safety requirements in ambulatory health care facilities Emergency preparedness & planning requirements for non-fire emergencies to include power outages and medical emergencies Clarifies roof top access and obstructions

9 Local Laws in 2013 now part of 2014 Building Code: 80/2013 Capture Storm water to Prevent Flooding 9 NYP Design Specifications Update 2014 Highlights Building Resiliency Local Laws to Building Code 81/2013 Analyze Wind Risks 82/2013 Clarify Construction Requirements in Flood Zones 83/2013 Prevent Sewage Backflow 98/2013 Create Emergency Plans 99/2013 Remove Barriers to Elevating Building Systems 100/2013 Relocate and Protect Building Systems 101/2013 Prevent Wind Damage to Existing Buildings 108/2013 Add Hookups for Temporary Generators & Boilers 109/2013 Remove Barriers to Sidewalk Flooding 143/2013 Safeguard Toxic Materials Stored in Flood Zones

10 Equipment pre- approval process developed 10 with NYP Facilities Operations to standardize to improve maintenance and Equipment Selection Process reduce the number of spare parts Or Equal was eliminated from the recommended manufacturers when 3 or more manufacturers were listed. A handful of Proprietary equipment manufacturers such as: ASCO Automatic Transfer Switches were identified as NYPH Standards. Architects and Engineering Firms are to use selected NYP pre- approved Equipment from the Equipment Cut e-book that resides on the portal.

11 11 Locating MEP Standards and Equipment Cuts on Portal

12 12 Updating and Maintaining the Design Specifications and Equipment Cuts We encourage all stakeholders to provide updates and suggestions through FDC-E, including: FDC-Project teams & A/E Design Firms FO Directors, Managers and Shop personnel FDC-E will be responsible for the updating of the Standard Standards will be maintained on a 3-year cycle Changes in sections will be highlighted at each cycle