ISO INTERNATIONAL STANDARD
|
|
- Charity Sherman
- 6 years ago
- Views:
Transcription
1 INTERNATIONAL STANDARD ISO First edition Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Pipes with flexible joints intended to be installed using jacking techniques Systèmes de canalisations en matières plastiques pour l'alimentation en eau avec ou sans pression, pour l'irrigation ou l'assainissement Systèmes en matières plastiques thermodurcissables renforcés de verre (PRV) à base de résine de polyester non saturé (UP) Tubes avec assemblages flexibles destinés à être installés par les techniques de poussée Reference number ISO 25780:2011(E) ISO 2011
2 COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii
3 Contents Page Foreword...iv 1 Scope Normative references Terms and definitions Requirements Classification Pipe properties Materials Pipe wall construction Reference conditions for testing Elapsed time, x, for determination of long-term properties Joint properties Pipes Geometrical characteristics Mechanical characteristics Resistance to strain corrosion Longitudinal compressive strength Permissible jacking forces Specific initial longitudinal compressive modulus, E c,m Resistance of pressure pipes to internal pressure Marking Joint performance General requirements Interchangeability Geometrical characteristics Design Performance requirements Test method additional information...25 Annex A (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the longitudinal compressive properties of a pipe, using a sample of prism test-pieces cut from a ring from the pipe...27 Annex B (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the compressive properties of pipes, using spool test-pieces...34 Annex C (normative) Procedure for the calculation of the permissible jacking force on a GRP-(UP) pipe, F perm,p...39 Bibliography...51 iii
4 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. iv
5 COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii
6 Contents Page Foreword...iv 1 Scope Normative references Terms and definitions Requirements Classification Pipe properties Materials Pipe wall construction Reference conditions for testing Elapsed time, x, for determination of long-term properties Joint properties Pipes Geometrical characteristics Mechanical characteristics Resistance to strain corrosion Longitudinal compressive strength Permissible jacking forces Specific initial longitudinal compressive modulus, E c,m Resistance of pressure pipes to internal pressure Marking Joint performance General requirements Interchangeability Geometrical characteristics Design Performance requirements Test method additional information...25 Annex A (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the longitudinal compressive properties of a pipe, using a sample of prism test-pieces cut from a ring from the pipe...27 Annex B (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the compressive properties of pipes, using spool test-pieces...34 Annex C (normative) Procedure for the calculation of the permissible jacking force on a GRP-(UP) pipe, F perm,p...39 Bibliography...51 iii
7 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. iv
8 COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii
9 Contents Page Foreword...iv 1 Scope Normative references Terms and definitions Requirements Classification Pipe properties Materials Pipe wall construction Reference conditions for testing Elapsed time, x, for determination of long-term properties Joint properties Pipes Geometrical characteristics Mechanical characteristics Resistance to strain corrosion Longitudinal compressive strength Permissible jacking forces Specific initial longitudinal compressive modulus, E c,m Resistance of pressure pipes to internal pressure Marking Joint performance General requirements Interchangeability Geometrical characteristics Design Performance requirements Test method additional information...25 Annex A (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the longitudinal compressive properties of a pipe, using a sample of prism test-pieces cut from a ring from the pipe...27 Annex B (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the compressive properties of pipes, using spool test-pieces...34 Annex C (normative) Procedure for the calculation of the permissible jacking force on a GRP-(UP) pipe, F perm,p...39 Bibliography...51 iii
10 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. iv
11 COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel Fax copyright@iso.org Web Published in Switzerland ii
12 Contents Page Foreword...iv 1 Scope Normative references Terms and definitions Requirements Classification Pipe properties Materials Pipe wall construction Reference conditions for testing Elapsed time, x, for determination of long-term properties Joint properties Pipes Geometrical characteristics Mechanical characteristics Resistance to strain corrosion Longitudinal compressive strength Permissible jacking forces Specific initial longitudinal compressive modulus, E c,m Resistance of pressure pipes to internal pressure Marking Joint performance General requirements Interchangeability Geometrical characteristics Design Performance requirements Test method additional information...25 Annex A (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the longitudinal compressive properties of a pipe, using a sample of prism test-pieces cut from a ring from the pipe...27 Annex B (normative) Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the compressive properties of pipes, using spool test-pieces...34 Annex C (normative) Procedure for the calculation of the permissible jacking force on a GRP-(UP) pipe, F perm,p...39 Bibliography...51 iii
13 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. iv
ISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 25780 First edition 2011-05-15 Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage Glass-reinforced thermosetting plastics (GRP)
More informationISO 4901 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4901 Second edition 2011-08-15 Reinforced plastics based on unsaturated-polyester resins Determination of the residual styrene monomer content, as well as the content of other
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 18672-1 First edition 2009-06-15 Plastics piping systems for non-pressure drainage and sewerage Polyester resin concrete (PRC) Part 1: Pipes and fittings with flexible joints
More informationISO 3034 INTERNATIONAL STANDARD. Corrugated fibreboard Determination of single sheet thickness
INTERNATIONAL STANDARD ISO 3034 Second edition 2011-06-01 Corrugated fibreboard Determination of single sheet thickness Carton ondulé Détermination de l'épaisseur d'une feuille unique Reference number
More informationISO 75-3 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 75-3 Second edition 2004-05-15 Plastics Determination of temperature of deflection under load Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
More informationISO INTERNATIONAL STANDARD. Quality management systems Guidelines for configuration management
INTERNATIONAL STANDARD ISO 10007 Second edition 2003-06-15 Quality management systems Guidelines for configuration management Systèmes de management de la qualité Lignes directrices pour la gestion de
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1452-3 First edition 2009-12-01 Corrected version 2010-03-01 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 4179 Third edition 2005-02-15 Ductile iron pipes and fittings for pressure and non-pressure pipelines Cement mortar lining Tuyaux et raccords en fonte ductile pour canalisations
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 16831 First edition 2012-04-01 Non-destructive testing Ultrasonic testing Characterization and verification of ultrasonic thickness measuring equipment Essais non destructifs
More informationISO INTERNATIONAL STANDARD. Energy management systems Requirements with guidance for use
INTERNATIONAL STANDARD ISO 50001 First edition 2011-06-15 Energy management systems Requirements with guidance for use Systèmes de management de l'énergie Exigences et recommandations de mise en œuvre
More informationISO INTERNATIONAL STANDARD. Adhesives Determination of the solubility of water-soluble or alkalisoluble pressure-sensitive adhesives
INTERNATIONAL STANDARD ISO 25179 First edition 2010-02-15 Adhesives Determination of the solubility of water-soluble or alkalisoluble pressure-sensitive adhesives Adhésifs Détermination de la solubilité
More informationInformation technology Security techniques Information security management systems Requirements
INTERNATIONAL STANDARD ISO/IEC 27001 Second edition 2013-10-01 Information technology Security techniques Information security management systems Requirements Technologies de l information Techniques de
More informationISO INTERNATIONAL STANDARD. Implants for surgery Ceramic materials Part 1: Ceramic materials based on high purity alumina
INTERNATIONAL STANDARD ISO 6474-1 First edition 2010-02-15 Implants for surgery Ceramic materials Part 1: Ceramic materials based on high purity alumina Implants chirurgicaux Produits céramiques Partie
More informationISO 4986 INTERNATIONAL STANDARD. Steel castings Magnetic particle inspection. Pièces moulées en acier Contrôle par magnétoscopie
INTERNATIONAL STANDARD ISO 4986 Second edition 2010-03-15 Steel castings Magnetic particle inspection Pièces moulées en acier Contrôle par magnétoscopie Reference number ISO 4986:2010(E) ISO 2010 PDF disclaimer
More informationInformation technology Security techniques Information security management systems Requirements
INTERNATIONAL STANDARD ISO/IEC 27001 Second edition 2013-10-01 Information technology Security techniques Information security management systems Requirements Technologies de l information Techniques de
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 30300 First edition 2011-11-15 Information and documentation records Fundamentals and vocabulary Information et documentation Systèmes de gestion des documents d activité Principes
More informationISO INTERNATIONAL STANDARD. Welding coordination Tasks and responsibilities. Coordination en soudage Tâches et responsabilités
INTERNATIONAL STANDARD ISO 14731 Second edition 2006-10-01 Welding coordination Tasks and responsibilities Coordination en soudage Tâches et responsabilités Reference number ISO 14731:2006(E) ISO 2006
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13229 First edition 2010-03-15 Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 5628 Second edition 2012-01-15 Paper and board Determination of bending stiffness General principles for two-point, three-point and four-point methods Papier et carton Détermination
More informationISO INTERNATIONAL STANDARD. Rubber compounding ingredients Process oils Determination of glass transition temperature by DSC
INTERNATIONAL STANDARD ISO 28343 First edition 2010-09-01 Rubber compounding ingredients Process oils Determination of glass transition temperature by DSC Ingrédients de mélange du caoutchouc Huiles de
More informationISO INTERNATIONAL STANDARD. Petroleum, petrochemical and natural gas industries Hairpin-type heat exchangers
INTERNATIONAL STANDARD ISO 12212 First edition 2012-08-01 Petroleum, petrochemical and natural gas industries Hairpin-type heat exchangers Industries du pétrole et du gaz naturel Échangeurs thermiques
More informationISO 7401 INTERNATIONAL STANDARD. Road vehicles Lateral transient response test methods Open-loop test methods
INTERNATIONAL STANDARD ISO 7401 Third edition 2011-04-15 Road vehicles Lateral transient response test methods Open-loop test methods Véhicules routiers Méthodes d'essai de réponse transitoire latérale
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 11357-3 Second edition 2011-05-01 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization Plastiques
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 13894-2 First edition 2005-07-15 High-pressure decorative laminates Composite elements Part 2: Specifications for composite elements with wood-based substrates for interior use
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 17089-2 First edition 2012-10-01 Measurement of fluid flow in closed conduits Ultrasonic meters for gas Part 2: Meters for industrial applications Mesurage de débit des fluides
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 30000 First edition 2009-03-15 Ships and marine technology Ship recycling management systems Specifications for management systems for safe and environmentally sound ship recycling
More informationISO/IEC Information technology Governance of IT Framework and model
TECHNICAL REPORT ISO/IEC TR 38502 First edition 2014-02-01 Information technology Governance of IT Framework and model Technologies de l information Gouvernance des TI Cadre général et modèle Reference
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 20653 First edition 2006-08-15 Road vehicles Degrees of protection (IP-Code) Protection of electrical equipment against foreign objects, water and access Véhicules routiers Degrés
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 16204 First edition 2012-09-01 Durability Service life design of concrete structures Durabilité Conception de la durée de vie des structures en béton Reference number ISO 16204:2012(E)
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 9001 Fourth edition 2008-11-15 Quality management systems Requirements Systèmes de management de la qualité Exigences Reference number ISO 9001:2008(E) ISO 2008 PDF disclaimer
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 11600 Second edition 2002-10-01 Corrected version 2004-09-01 Building construction Jointing products Classification and requirements for sealants Construction immobilière Produits
More informationThis document is a preview generated by EVS
TECHNICAL REPORT ISO/IEC TR 33014 First edition 2013-12-01 Information technology Process assessment Guide for process improvement Technologies de l'information Évaluation des procédés Guide de l'amélioration
More informationISO INTERNATIONAL STANDARD. Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load
INTERNATIONAL STANDARD ISO 6336-6 First edition 2006-08-15 Calculation of load capacity of spur and helical gears Part 6: Calculation of service life under variable load Calcul de la capacité de charge
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 3826-3 First edition 2006-09-15 Plastics collapsible containers for human blood and blood components Part 3: Blood bag systems with integrated features Poches en plastique souple
More informationISO INTERNATIONAL STANDARD. Elastomeric seismic-protection isolators Part 2: Applications for bridges Specifications
INTERNATIONAL STANDARD ISO 22762-2 Second edition 2010-11-01 Elastomeric seismic-protection isolators Part 2: Applications for bridges Specifications Appareils d'appuis structuraux en élastomère pour protection
More informationISO INTERNATIONAL STANDARD. Metallic materials Tensile testing Part 2: Method of test at elevated temperature
INTERNATIONAL STANDARD ISO 6892-2 First edition 2011-02-15 Metallic materials Tensile testing Part 2: Method of test at elevated temperature Matériaux métalliques Essai de traction Partie 2: Méthode d'essai
More informationISO 8339 INTERNATIONAL STANDARD. Building construction Sealants Determination of tensile properties (Extension to break)
INTERNATIONAL STANDARD ISO 8339 Second edition 2005-06-15 Building construction Sealants Determination of tensile properties (Extension to break) Construction immobilière Mastics Détermination des propriétés
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21610 First edition 2009-12-15 Corrosion of metals and alloys Accelerated corrosion test for intergranular corrosion susceptibility of austenitic stainless steels Corrosion des
More informationISO INTERNATIONAL STANDARD. Compressed air Part 7: Test method for viable microbiological contaminant content
INTERNATIONAL STANDARD ISO 8573-7 First edition 2003-05-01 Compressed air Part 7: Test method for viable microbiological contaminant content Air comprimé Partie 7: Méthode d'essai pour la détermination
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10567 Second edition 2007-10-01 Earth-moving machinery Hydraulic excavators Lift capacity Engins de terrassement Pelles hydrauliques Capacité de levage Reference number ISO 10567:2007(E)
More informationISO 5178 INTERNATIONAL STANDARD. Destructive tests on welds in metallic materials Longitudinal tensile test on weld metal in fusion welded joints
INTERNATIONAL STANDARD ISO 5178 First edition 2001-02-01 Destructive tests on welds in metallic materials Longitudinal tensile test on weld metal in fusion welded joints Essais destructifs des soudures
More informationISO 604 INTERNATIONAL STANDARD. Plastics Determination of compressive properties. Plastiques Détermination des propriétés en compression
INTERNATIONAL STANDARD ISO 604 Third edition 2002-03-01 Plastics Determination of compressive properties Plastiques Détermination des propriétés en compression Reference number ISO 604:2002(E) ISO 2002
More informationISO 638 INTERNATIONAL STANDARD. Paper, board and pulps Determination of dry matter content Oven-drying method
INTERNATIONAL STANDARD ISO 638 Second edition 2008-10-01 Paper, board and pulps Determination of dry matter content Oven-drying method Papiers, cartons et pâtes Détermination de la teneur en matières sèches
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 15547-2 First edition 2005-11-01 Petroleum, petrochemical and natural gas industries Plate-type heat exchangers Part 2: Brazed aluminium plate-fin heat exchangers Industries
More informationISO 2965 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 2965 Third edition 2009-05-15 Materials used as cigarette papers, filter plug wrap and filter joining paper, including materials having a discrete or oriented permeable zone
More informationISO INTERNATIONAL STANDARD. Random sampling and randomization procedures. Modes opératoires d'échantillonnage et de répartition aléatoires
INTERNATIONAL STANDARD ISO 24153 First edition 2009-12-01 Random sampling and randomization procedures Modes opératoires d'échantillonnage et de répartition aléatoires Reference number ISO 24153:2009(E)
More informationISO INTERNATIONAL STANDARD. Metallic materials Vickers hardness test Part 3: Calibration of reference blocks
INTERNATIONAL STANDARD ISO 6507-3 Third edition 2005-12-15 Metallic materials Vickers hardness test Part 3: Calibration of reference blocks Matériaux métalliques Essai de dureté Vickers Partie 3: Étalonnage
More informationINTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8362-3 Second edition 2001-12-01 Injection containers and accessories Part 3: Aluminium caps for injection vials Récipients et accessoires pour produits injectables Partie 3:
More informationISO INTERNATIONAL STANDARD. Diesel engines NOx reduction agent AUS 32 Part 4: Refilling interface
INTERNATIONAL STANDARD ISO 22241-4 First edition 2009-08-01 Diesel engines NOx reduction agent AUS 32 Part 4: Refilling interface Moteurs diesel Agent AUS 32 de réduction des NOx Partie 4: Interface de
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12243 First edition 2003-10-01 Medical gloves made from natural rubber latex Determination of water-extractable protein using the modified Lowry method Gants médicaux à base
More informationISO 648 INTERNATIONAL STANDARD. Laboratory glassware Single-volume pipettes. Verrerie de laboratoire Pipettes à un volume. Second edition
INTERNATIONAL STANDARD ISO 648 Second edition 2008-10-15 Laboratory glassware Single-volume pipettes Verrerie de laboratoire Pipettes à un volume Reference number ISO 648:2008(E) ISO 2008 PDF disclaimer
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 24353 First edition 2008-09-15 Hygrothermal performance of building materials and products Determination of moisture adsorption/desorption properties in response to humidity
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8362-7 Second edition 2006-04-15 Injection containers and accessories Part 7: Injection caps made of aluminiumplastics combinations without overlapping plastics part Récipients
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21138-3 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)
More informationISO 185 INTERNATIONAL STANDARD. Grey cast irons Classification. Fontes à graphite lamellaire Classification. Second edition
INTERNATIONAL STANDARD ISO 185 Second edition 2005-08-15 Grey cast irons Classification Fontes à graphite lamellaire Classification Reference number ISO 185:2005(E) ISO 2005 PDF disclaimer This PDF file
More informationISO INTERNATIONAL STANDARD. Buildings and constructed assets Service life planning Part 10: When to assess functional performance
INTERNATIONAL STANDARD ISO 15686-10 First edition 2010-06-01 Buildings and constructed assets Service life planning Part 10: When to assess functional performance Bâtiments et biens immobiliers construits
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 21138-2 First edition 2007-10-15 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride)
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 19001 Second edition 2013-03-15 In vitro diagnostic medical devices Information supplied by the manufacturer with in vitro diagnostic reagents for staining in biology Dispositifs
More informationISO INTERNATIONAL STANDARD. Equipment for crop protection Induction hoppers Part 2: General requirements and performance limits
INTERNATIONAL STANDARD ISO 21278-2 First edition 2008-11-15 Equipment for crop protection Induction hoppers Part 2: General requirements and performance limits Matériel de protection des cultures Incorporateurs
More informationISO/IEC INTERNATIONAL STANDARD. Information technology Security techniques Information security management systems Requirements
INTERNATIONAL STANDARD ISO/IEC 27001 First edition 2005-10-15 Information technology Security techniques Information security management systems Requirements Technologies de l'information Techniques de
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 22196 Second edition 2011-08-01 Measurement of antibacterial activity on plastics and other non-porous surfaces Mesurage de l'action antibactérienne sur les surfaces en plastique
More informationISO INTERNATIONAL STANDARD. Cutting tools Designation of high-speed steel groups. Outils coupants Désignation des groupes d'aciers rapides
INTERNATIONAL STANDARD ISO 11054 Second edition 2006-01-15 Cutting tools Designation of high-speed steel groups Outils coupants Désignation des groupes d'aciers rapides Reference number ISO 11054:2006(E)
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 13564-1 First edition 2012-09-15 Powered industrial trucks Test methods for verification of visibility Part 1: Sit-on and stand-on operator trucks and variable-reach trucks up
More informationISO INTERNATIONAL STANDARD. Rigid cellular plastics Spray-applied polyurethane foam for thermal insulation Part 2: Application
INTERNATIONAL STANDARD ISO 8873-2 First edition 2007-05-01 Rigid cellular plastics Spray-applied polyurethane foam for thermal insulation Part 2: Application Plastiques alvéolaires rigides Mousse de polyuréthanne
More informationISO INTERNATIONAL STANDARD. Cutting tools Designation of high-speed steel groups. Outils coupants Désignation des groupes d'aciers rapides
INTERNATIONAL STANDARD ISO 11054 Second edition 2006-01-15 Cutting tools Designation of high-speed steel groups Outils coupants Désignation des groupes d'aciers rapides Reference number ISO 11054:2006(E)
More informationISO INTERNATIONAL STANDARD. Specification for security management systems for the supply chain
INTERNATIONAL STANDARD ISO 28000 First edition 2007-09-15 Specification for security management systems for the supply chain Spécifications pour les systèmes de management de la sûreté pour la chaîne d'approvisionnement
More informationISO INTERNATIONAL STANDARD. Pallets for materials handling Quality of assembly of new wooden pallets
INTERNATIONAL STANDARD ISO 18334 Second edition 2010-06-01 Pallets for materials handling Quality of assembly of new wooden pallets Palettes pour la manutention et le transport des marchandises Qualité
More informationISO INTERNATIONAL STANDARD. Water quality Determination of sulfates Method by continuous flow analysis (CFA)
INTERNATIONAL STANDARD ISO 22743 First edition 2006-04-15 Water quality Determination of sulfates Method by continuous flow analysis (CFA) Qualité de l'eau Dosage des sulfates Méthode par analyse en flux
More informationISO INTERNATIONAL STANDARD. Earth-moving machinery Operator enclosure environment Part 2: Air filter element test method
INTERNATIONAL STANDARD ISO 10263-2 Second edition 2009-02-01 Earth-moving machinery Operator enclosure environment Part 2: Air filter element test method Engins de terrassement Environnement de l'enceinte
More informationISO INTERNATIONAL STANDARD. Ships and marine technology Lowlocation lighting (LLL) on passenger ships Arrangement
INTERNATIONAL STANDARD ISO 15370 Second edition 2010-02-15 Ships and marine technology Lowlocation lighting (LLL) on passenger ships Arrangement Navires et technologie maritime Éclairage situé en bas sur
More informationISO INTERNATIONAL STANDARD. Self-adhesive hanging devices for infusion bottles and injection vials Requirements and test methods
INTERNATIONAL STANDARD ISO 15137 First edition 2005-07-15 Self-adhesive hanging devices for infusion bottles and injection vials Requirements and test methods Systèmes de suspension autoadhésifs pour flacons
More informationISO INTERNATIONAL STANDARD. Rigid cellular plastics Spray-applied polyurethane foam for thermal insulation Part 3: Test methods
INTERNATIONAL STANDARD ISO 8873-3 First edition 2007-05-01 Rigid cellular plastics Spray-applied polyurethane foam for thermal insulation Part 3: Test methods Plastiques alvéolaires rigides Mousse de polyuréthanne
More informationISO INTERNATIONAL STANDARD. Space systems Launch-vehicle-tospacecraft flight environments telemetry data processing
INTERNATIONAL STANDARD ISO 15862 First edition 2009-02-01 Space systems Launch-vehicle-tospacecraft flight environments telemetry data processing Systèmes spatiaux Traitement des données télémétriques
More informationISO INTERNATIONAL STANDARD. Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General
INTERNATIONAL STANDARD ISO 16881-1 First edition 2005-05-15 Cranes Design calculation for rail wheels and associated trolley track supporting structure Part 1: General Appareils de levage à charge suspendue
More informationISO 4575 INTERNATIONAL STANDARD. Plastics Poly(vinyl chloride) pastes Determination of apparent viscosity using the Severs rheometer
INTERNATIONAL STANDARD ISO 4575 Third edition 2007-05-01 Plastics Poly(vinyl chloride) pastes Determination of apparent viscosity using the Severs rheometer Plastiques Pâtes de poly(chlorure de vinyle)
More informationISO Information and documentation Management systems for records Fundamentals and vocabulary
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 30300 First edition 2011-11-15 Information and documentation records Fundamentals and vocabulary Information et documentation Systèmes de gestion
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 24034 Second edition 2010-10-01 Welding consumables Solid wire electrodes, solid wires and rods for fusion welding of titanium and titanium alloys Classification Produits consommables
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 11357-6 Second edition 2008-06-15 Corrected version 2008-11-15 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal
More informationISO INTERNATIONAL STANDARD. Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 5: Chemical loads
INTERNATIONAL STANDARD ISO 16750-5 Second edition 2010-04-15 Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 5: Chemical loads Véhicules routiers Spécifications
More informationISO INTERNATIONAL STANDARD. Water quality Detection and enumeration of Pseudomonas aeruginosa Method by membrane filtration
INTERNATIONAL STANDARD ISO 16266 First edition 2006-04-15 Water quality Detection and enumeration of Pseudomonas aeruginosa Method by membrane filtration Qualité de l'eau Recherche et dénombrement de Pseudomonas
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10456 Third edition 2007-12-15 Building materials and products Hygrothermal properties Tabulated design values and procedures for determining declared and design thermal values
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10893-2 First edition 2011-04-01 Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 17873 First edition 2004-10-15 Nuclear facilities Criteria for the design and operation of ventilation systems for nuclear installations other than nuclear reactors Installations
More informationISO 8407 INTERNATIONAL STANDARD. Corrosion of metals and alloys Removal of corrosion products from corrosion test specimens
INTERNATIONAL STANDARD ISO 8407 Second edition 2009-11-01 Corrosion of metals and alloys Removal of corrosion products from corrosion test specimens Corrosion des métaux et alliages Élimination des produits
More informationISO INTERNATIONAL STANDARD. Glass in building Explosion-resistant security glazing Test and classification by shock-tube loading
INTERNATIONAL STANDARD ISO 16934 First edition 2007-07-01 Glass in building Explosion-resistant security glazing Test and classification by shock-tube loading Verre dans la construction Vitrages de sécurité
More informationISO INTERNATIONAL STANDARD. Hot-rolled stainless steel plates Tolerances on dimensions and shape
INTERNATIONAL STANDARD ISO 18286 Second edition 2008-12-15 Hot-rolled stainless steel plates Tolerances on dimensions and shape Tôles en acier inoxydable laminées à chaud Tolérances sur les dimensions
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 3601-2 Second edition 2016-07-15 Fluid power systems O-rings Part 2: Housing dimensions for general applications Transmissions hydrauliques et pneumatiques Joints toriques Partie
More informationISO INTERNATIONAL STANDARD. Founding Ausferritic spheroidal graphite cast irons Classification
INTERNATIONAL STANDARD ISO 17804 First edition 2005-11-01 Founding Ausferritic spheroidal graphite cast irons Classification Fonderie Fonte ausferritique à graphite sphéroïdal Classification Reference
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 18553 First edition 2002-03-01 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds Méthode d'estimation
More informationISO 3069 INTERNATIONAL STANDARD. End-suction centrifugal pumps Dimensions of cavities for mechanical seals and for soft packing
INTERNATIONAL STANDARD ISO 3069 Second edition 2000-11-01 End-suction centrifugal pumps Dimensions of cavities for mechanical seals and for soft packing Pompes centrifuges à aspiration en bout Dimensions
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 21048 Second edition 2014-02-15 Plastics Epoxy resins Determination of 1,2-glycol content Plastiques Résines époxydes Détermination de la teneur en 1,2-glycol Reference number
More informationISO INTERNATIONAL STANDARD. Cranes Stiffness Bridge and gantry cranes
INTERNATIONAL STANDARD ISO 22986 First edition 2007-04-15 Cranes Stiffness Bridge and gantry cranes Appareils de levage à charge suspendue Rigidité Ponts et portiques roulants Reference number ISO 22986:2007(E)
More informationISO/IEC INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO/IEC 25041 First edition 2012-10-15 Systems and software engineering Systems and software Quality Requirements and Evaluation (SQuaRE) Evaluation guide for developers, acquirers
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 14397-2 Second edition 2007-09-15 Earth-moving machinery Loaders and backhoe loaders Part 2: Test method for measuring breakout forces and lift capacity to maximum lift height
More informationISO INTERNATIONAL STANDARD. Building construction Jointing products Specifications for test substrates
INTERNATIONAL STANDARD ISO 13640 First edition 1999-12-15 Building construction Jointing products Specifications for test substrates Construction immobilière Matériaux pour joints Prescriptions relatives
More informationISO 9514 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 9514 Second edition 2005-04-15 Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 17080 First edition 2005-10-15 Manually portable agricultural and forestry machines and powered lawn and garden equipment Design principles for single-panel product safety labels
More informationISO 1409 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1409 Fifth edition 2006-09-15 Plastics/rubber Polymer dispersions and rubber latices (natural and synthetic) Determination of surface tension by the ring method Plastiques/caoutchouc
More informationISO INTERNATIONAL STANDARD. Metallic powders Determination of apparent density Part 1: Funnel method
INTERNATIONAL STANDARD ISO 3923-1 Third edition 2008-05-01 Metallic powders Determination of apparent density Part 1: Funnel method Poudres métalliques Détermination de la masse volumique apparente Partie
More informationISO INTERNATIONAL STANDARD. Road vehicles Securing of cargo in delivery vans Requirements and test methods
INTERNATIONAL STANDARD ISO 27956 First edition 2009-03-15 Road vehicles Securing of cargo in delivery vans Requirements and test methods Véhicules routiers Arrimage des charges à bord des camionnettes
More information