Elevated Work Safety Meeting
|
|
- Roberta Jacobs
- 6 years ago
- Views:
Transcription
1 Elevated Work Safety Meeting 1
2 Elevated Work There are many jobs that require working at heights This requires the use of walking working surfaces such as ladders, scaffolds and stairways Safety in elevated work areas requires companies to follow strict standards for height, width, building materials, load capacity and proper housekeeping 2
3 Ladders Designed primarily to provide access to an elevated area Must not be used as a work platform unless the job can be performed using only one hand Be constructed according to OSHA regulations 3
4 Ladders Get authorization to perform elevated work Clear footing area of excess tools, debris, waste and other obstructions Place the ladder on a firm, level surface Fully open the legs of the ladder Use proper PPE Fall protection if necessary Secure tools and equipment properly Carry only necessary tools in pockets or tool belt Attach a hand line and lift items once on stable surface Maintain a 3-point contact with the ladder 4
5 3-point Contact
6 Inspect the following before using a ladder Footing Rungs or steps Side rails Hinges Spreaders Ladder Inspection 6
7 Damaged Ladders Put a warning tag on a damaged ladder immediately Report a damaged ladder to a supervisor Take a damaged ladder out of service until it is repaired Portable ladders are often damaged by being moved from worksite to worksite and while in storage Fixed ladders may deteriorate if they are exposed to the weather or corrosive chemicals 7
8 Two types of ladders commonly found in industrial facilities Portable Fixed Ladders 8
9 Portable Ladders Avoid overreaching when performing work from a ladder The worker s belt buckle must never pass the side rail of the ladder Never allow more than one person at a time on a ladder 9
10 Portable Ladders Portable ladders are subdivided into two categories Step ladders Extension ladders 10 10
11 Step Ladders A step ladder is used to perform work at relatively low levels or when an appropriate upper support is not available 11 11
12 Extension Ladders Most commonly used to transit to a higher level where permanent access is not provided Ladder footing must be on a firm, level surface to prevent the base from kicking out Open ladder must maintain a 4:1 slope Angled so the base of the ladder is one foot away from the vertical plane for each rise of four feet Top of the ladder must rest against a sturdy support Top of the ladder must extend three feet past the upper level Must be tied off to avoid slippage 12 12
13 Extension Ladders 13 13
14 Metal Ladders Never use a metal ladder when electrical hazards are present Be aware of overhead power lines and other electrical connections when setting up and moving a metal ladder 14 14
15 Fixed Ladders Provided in frequently accessed, elevated areas A visual inspection ensures it is in an acceptable condition before climbing A fixed ladder higher than 20 feet must be equipped with fall protection cages or other protective devices Rest platforms must be provided every 30 feet 15 15
16 Fixed Ladders 16 16
17 Scaffolds Designed primarily as a work platform Allow workers to perform a job that Takes a long time Requires both hands Requires more than one person Only use a scaffold for its intended purpose based on the type of scaffold used A stairway or ladder must be provided and used for climbing onto a scaffold Always place on a firm level surface 17 17
18 Scaffolds Store in a place that will avoid excessive weathering or damage Securely fasten risers and braces with the locking mechanism properly engaged Keep materials away from the bracing and footing of a scaffold Use of scaffolds that are covered with snow, ice or other slippery materials is prohibited Use of shore and lean-to scaffolds is prohibited 18 18
19 Scaffolds 19 19
20 Types of Scaffolds Pole Tube and coupler Fabricated frame Outrigger Single point adjustable suspension Two point adjustable suspension 20 20
21 Wheeled Scaffolds Can only be used on a smooth, firm, level surface Workers are only allowed on the scaffold when it is stationary 21 21
22 Qualified Worker Responsibilities Design and assembly of a scaffold Dismantle or move a scaffold Repair or alter a scaffold Determine the maximum load capacity and ensure that it is not exceeded at any time Inspection of a scaffold 22 22
23 Scaffold Inspection Must be inspected for Deterioration Damage Missing parts Must be inspected Before workers are allowed to use them Before each shift After any occurrence that may affect the stability or safe use of the scaffolding 23 23
24 Load Capacity The structure that the scaffold is secured to must be capable of withstanding the load The load includes Vertical load, such as the weight of the scaffold Horizontal load, such as the wind blowing on tarps All scaffolds and components must support, without failure, its own weight and at least four times the maximum intended load applied or transmitted to it 24 24
25 Height Limitations The height of a freestanding scaffold is limited to four times the smallest dimension of the base For example, a 5 x 10 freestanding scaffold cannot exceed a height of 20 feet tall Guying or tying is necessary if a scaffold needs to be taller Secure scaffold to a tall structure Prevent swaying or displacement Must be tied at least every 30 feet horizontally and every 26 feet vertically 25 25
26 Planking Must be made of scaffolding grade material Must completely cover the entire working platform Must form a smooth, continuous working surface Must not have any gaps large enough for tools or materials to fall through Wooden planking must extend past the end supports by no less than 6 inches and no more than 12 inches Metal planking must not extend past the end supports 26 26
27 Scaffold Hazards Electrical hazards can include Working near energized or exposed electric lines Using electric power tools Using welding equipment Scaffolds must not be closer than 10 feet to power lines Electric power tools create a risk of electrocution or shock because a metal frame scaffold is conductive Scaffold should be grounded to reduce the risk of injury To reduce the risk of electrocution or shock Use a GFCI Assured Grounding program 27 27
28 Scaffold Hazards Area above and below the work being done on a scaffold can create fall hazards Area must be inspected before the job begins and cleared of any objects with the potential to fall on workers Ladders should not be used on a scaffold to increase the working height unless specific conditions are met Workers should not stand on boxes, crates or barrels to increase their working height 28 28
29 Fall and Falling Object Protection A fall arrest system should be worn even if a scaffold is equipped with handrails The company must ensure that wearing fall protection does not create a greater hazard The tie-off point selected for a fall arrest system cannot be a part of the scaffold A hard hat must be worn at all times if there is a chance of falling hand tools, debris or other small objects 29 29
30 Fall and Falling Object Protection Eliminate the chance of materials falling from the scaffold Do not stack materials where they can be knocked off Tie hand tools and equipment to a safety line The area below the scaffold should be protected using a barricade and worker access must be restricted 30 30
31 Fall and Falling Object Protection Handrails must be installed on all open ends and sides of scaffolding greater than 10 feet high Handrails must be equipped with a top rail between 36 and 42 inches high and a mid-rail Never climb or work from the handrail, midrail, braces or cross-braces of a scaffold system Toeboards must be placed along the edge of platforms greater than 10 feet high for a distance sufficient to protect workers below Toeboards must be at least 4 inches high to prevent loose objects from being kicked over the side 31 31
32 Fall and Falling Object Protection Additional protection that will deflect or contain falling objects can include Toeboards Screens Guardrails Debris nets Catch platforms Canopy structures 32 32
33 Elevated Work Quiz NAME: November 2012 Safety Meeting DATE: INSTRUCTIONS: Sign and date this quiz sheet. Circle the letter representing the correct answer to each question below. 1. are designed primarily to provide access to an elevated area. A. Ladders B. Scaffolds C. Guardrails D. Toeboards 2. are designed primarily as a work platform. A. Ladders B. Scaffolds C. Guardrails D. Toebboards 3. Two types of ladders commonly found in industrial facilities are ladders and fixed ladders. A. Portable B. Corporate C. Tall D. Rope 4. Never use a metal ladder when hazards are present. A. Water B. Biological C. Electrical D. Fall 5. Put a on a damaged ladder immediately. A. Body harness B. Safety net C. Stop sign D. Warning tag 6. Carry only necessary tools in pockets or tool belt when climbing a ladder. A. True B. False 7. All scaffolds and components must support, without failure, its own weight and at least times the maximum intended load applied or transmitted to it. A. Twenty B. Five C. Four D. One hundred 8. A fall arrest system should be worn even if a scaffold is equipped with handrails. A. True B. False 9. A scaffold must be inspected. A. Before workers are allowed to use them B. Before each shift C. After any occurrence that may affect the stability or safe use of the scaffolding D. All of the above 10. Shore and lean to scaffolds can be used only if the job is done quickly. A. True B. False 1 QUIZ-SFMTG-ELVWRK
34 Elevated Work Answer Key November 2012 Safety Meeting Below is the answer key for the quiz. 1. A 2. B 3. A 4. C 5. D 6. A 7. C 8. A 9. D 10. B KEY-SFMTG-ELVWRK QUIZ-SFMTG-ELVWRK
35 Instructor Name: CAP Safety Meetings Student Roster Safety Meeting Date: Safety Meeting Name: Company Name: Student Instructions: Print and sign your name. Also, provide your employee number or SSN as per your company policy. Print Student Name (Clearly) Student Signature EMP# or SSN Copyright-PEC/Premier Safety Management, Inc-All rights reserved
SCAFFOLDS Revision No: 3
PAGE 1 OF 6 1.0 PURPOSE/ SCOPE To communicate the safety requirements for the erection, inspection and safe use of scaffolds. Compliance with these requirements will assure employee safety while working
More informationScaffolds. OSHA Office of Training & Education 1
Scaffolds OSHA Office of Training & Education 1 What Is A Scaffold? An elevated, temporary work platform Three basic types: Supported scaffolds -- platforms supported by rigid, load bearing members, such
More informationBP U.S. Pipelines and Logistics (USPL) Safety Manual Page 1 of 7
Safety Manual Page 1 of 7 Scaffolds 1. Purpose This policy establishes the basic safety requirements and safe work practices for the erection, use, inspection, movement, and dismantling of scaffolding.
More informationSample Written Program. For. Scaffolds
Sample Written Program For Scaffolds 1 Scaffold Safety Program (COMPANY NAME) Purpose The purpose of this safety policy and procedure is to establish guidelines for the protection of {COMPANY} employees
More informationReliant Holdings Ltd Safety Management System
Preparation: Safety Mgr Authority: President Issuing Dept: Safety Page: Page 1 of 7 Purpose The purpose of this program is to prevent injuries due to falls from elevated work areas and ensure employees
More informationDocument Number: HSE Created: February 21, 2013 SCAFFOLDING. Author: A Holland
Document Number: HSE33-001 Created: February 21, 2013 SCAFFOLDING Author: A Holland MAPP Construction - Corporate 344 Third Street Baton Rouge, LA 70801 (225) 757-0111 MAPP Construction - Houston 11511
More informationScaffolding Procedures
Procedures Purpose It is the purpose of this company in issuing these procedures to further ensure a safe workplace based on the following formal, written procedures for scaffold work. Application This
More informationSection 8. Walking/Working Surfaces. 8.1 Objective. 8.2 Roles and Responsibilities. 8.3 General Requirements. Competent Person
International Environmental Health and Safety (IEHS) Section 8 Walking/Working Surfaces 8.1 Objective The Walking/Working Surfaces program has been developed for IEHS and project employees working on site,
More informationDEPAUL UNIVERSITY. Scaffolding Program. Environmental Health & Safety. April 2017
DEPAUL UNIVERSITY Scaffolding Program Environmental Health & Safety April 2017 1 TABLE OF CONTENTS SECTION PAGE NO. 1.0 PURPOSE 2 2.0 SCOPE 2 3.0 SCAFFOLDING ERECTOR 2 4.0 GENERAL 2 5.0 WOOD SCAFFOLDING
More informationSCAFFOLDING PROCEDURE
SCAFFOLDING PROCEDURE 1 Table of Contents 1 PURPOSE... 3 2 PROGRAM COMPLIANCE... 3 3 SCOPE... 3 4 DEFINITIONS... 3 5 RESPONSIBILITES... 4 6 SCAFFOLD INSPECTION... 5 7 SCAFFOLD USE... 5 8 SCAFFOLD REQUIREMENTS...
More informationCopies of the written program may be obtained at Where are copies of this written plan kept? (Insert building/room, etc.).
Scaffolding Safety Procedures for Construction Purpose It is this company's purpose in issuing these procedures to further ensure a safe workplace based on the following formal, written procedures for
More informationSTANDARD PRACTICE INSTRUCTION
STANDARD PRACTICE INSTRUCTION DATE: March 1, 2001 SUBJECT: Scaffolding Safety Program. REGULATORY STANDARDS: 29 CFR 1910.28 Safety Requirements For Scaffolding. 29 CFR 1910.29 Manually Propelled Mobile
More informationDUQUESNE UNIVERSITY SAFETY PROGRAM FOR WORKING AT ELEVATED HEIGHTS
DUQUESNE UNIVERSITY SAFETY PROGRAM FOR WORKING AT ELEVATED HEIGHTS Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Responsibilities 1 Scaffolding 2 Ladders
More informationScaffolding Safety. Scaffolding
Scaffolding Safety Scaffolding 1926.450 - Scope, Application Covers all scaffolds used in workplaces Does not apply to crane or derrick suspended personnel platforms, which are covered by 1926.550(g) Aerial
More informationScaffolding. Safety Guide. STOP! Before you climb
Scaffolding Safety Guide Printed FEB 2015 rebr. AUG 2016 Contents Safety Guide Disclaimer... 1 Safety Guide Objectives... 2 Roles & Responsibilities of Workplace Parties Employers, Supervisors, Workers...
More informationBP OIL -- TOLEDO REFINERY
BP OIL -- TOLEDO REFINERY Document Type: Procedure Refinery Wide Procedure No.: SAF 076 Effective Date: 3/31/17 Scaffold Procedure Revision No.: 8 Owner: E. Stewart / N. Weber Authorized By: Chris Conley
More informationWORKING AT HEIGHT PROCEDURE
Page 1 of 8 AL-Yamama Engineering Company HSSE Department (s) WORKING AT HEIGHT PROCEDURE Page 1 of 8 Page 2 of 8 Introduction Work at height is any work activity that is performed where the work is to
More informationChapter 17 - Ladders and Scaffolds
Chapter 17 Ladders and Scaffolds Chapter 17 - Ladders and Scaffolds Ladders Ladders must be in good condition, made of suitable material, of proper length, and of the correct type for the use intended.
More informationOSHA Rules for Scaffolding
OSHA Rules for Scaffolding A) Objectives: 1. 2. 3. Don t let the scaffold fall. Don t fall off the scaffold. Don t let the material fall off the scaffold. Name of Competent Person: Name of Qualified Person:
More informationScissor Lift Safety. Supervisor Manual 29 CFR , 451, 452, 454. Page 0
Scissor Lift Safety 29 CFR.1926.450, 451, 452, 454 Supervisor Manual Page 0 Table of Contents Purpose... 2 Program Responsibilities... 2 Management... 2 Supervisors... 2 Employees... 2 Definitions... 3
More informationTAMPA ELECTRIC COMPANY ENERGY SUPPLY SCAFFOLD PROGRAM
TABLE OF CONTENTS TITLE PAGE # PURPOSE / INTRODUCTION 1 RESPONSIBILITY 2 EMPLOYEE TRAINING AND DOCUMENTATION 3-4 PERIODIC PROGRAM EVALUATION 4 GENERAL SCAFFOLD ERECTING/DISASSEMBLING REQUIREMENTS 5-7 SCAFFOLDING
More informationSafety Policy and Procedure
Safety Policy and Procedure Policy Number: 026 Authorized By: The Cianbro Companies Alan Burton Title: Scaffold Safety is Everyone s Responsibility Effective Date: 06/01/97 Page 1 of 17 1 Status 1.1 Update
More informationWalking and Working Surfaces in Construction Environments. Leader s Guide and Quiz
4786 Walking and Working Surfaces in Construction Environments Leader s Guide and Quiz INTRODUCTION TO THE PROGRAM Structure and Organization Information in this program is presented in a definite order
More informationReferences. EM , Sections 22 OSHA 29CFR (Subpart L ) UFGS [Latest] ANSI A
References EM385-1-1, Sections 22 OSHA 29CFR 1926.450 (Subpart L ) UFGS-01 35 29[Latest] ANSI A10.8-1988 What Is A Scaffold? An elevated, temporary work platform Three basic types: Supported scaffolds
More informationSupported Scaffold Inspections
Supported Scaffold Inspections May 2016 Inspect scaffolds and scaffold parts daily, before each work shift, and after any event that may have caused damage. Check to see if power lines near scaffolds are
More informationCitations in brackets are from Title 8 of the California Administrative Code.
SAFETY WALKAROUND CHECKLIST SCAFFOLDS 2001 Date Prepared: Project Name/No: By: Location: Check the box if the statement is true. Fill in the blanks where the appears. Citations in brackets are from Title
More informationIntroduction. Estimated length: 30 minutes Audience: construction workers
Introduction Scaffold User Training Welcome! The purpose of this Click Safety course is to provide instruction for basic safety provisions when using scaffolds in construction activities. Estimated length:
More information"WALKING AND WORKING SURFACES IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "WALKING AND WORKING SURFACES IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR
More informationFall Prevention Plan
Fall Prevention Plan April 10, 2018 i ii Table of Contents Review/Revision Summary... v Introduction... 1 Scope and Application... 1 Responsibilities... 1 Availability... 2 Annual Review... 2 Fall Prevention...
More informationScaffold Inspection Procedures for the Competent Person. Merle Errthum
Scaffold Inspection Procedures for the Competent Person Merle Errthum 2014 an elevated work platform. What is a Scaffold? What Is A Scaffold? An elevated, temporary work platform Three basic types: Supported
More informationWALKING AND WORKING SURFACES. Leader s Guide. Marcom Group Ltd.
1608 WALKING AND WORKING SURFACES Leader s Guide Marcom Group Ltd. Structure and Organization Information in this program is presented in a definite order so that employees will see the relationships between
More informationBECx Construction Phase Safety
BECx Construction Phase Safety What is the Number One Priority in Construction? Building Enclosure Commissioning: Train the Trainer Iowa State University, Ames Iowa May 10 12, 2016 Presented by William
More information2600SEG135 SAFETY STANDARD FOR INDUSTRIAL LADDERS AND STAIRCASES IN BUILDINGS
1.0 OBJECTIVE The purpose of this standard is to establish the minimum requirements applicable to standard ladders and staircases of general use in buildings and industrial installations of the Panama
More informationUniversal Panels & Accessories
Universal Panels & Accessories Erection Procedures INTRODUCTION Use common sense when working with Scaffold Your Safety is our #1 Concern Universal Scaffolds are designed with your safety in mind every
More informationScaffolding and Raised Platforms
Standard Operating Procedures Scaffolding and Raised Platforms Last Modified: JAN 2013 1 of 7 Scaffolding and Raised Platforms I Purpose To provide a guideline for personnel who work around or on stationary
More informationSystems Scaffold Tubular Scaffold Access Unit Installation Instructions
Systems Scaffold Tubular Scaffold Access Unit Installation Instructions 2 Tubular Scaffold Access Unit Installation Instructions LTUB7 Galvanized: 24.1 lb Label 7112A0003 NOTICE Please read and follow
More informationMulti-Purpose Scaffolding Instruction Manual
Limited Warranty World Factory, Inc. World Factory, Inc. (Seller) warrants to the original Buyer only, that each YellowStone Product will be free from defects in material and workmanship for a period of
More informationSAFE ERECTION AND USE OF ALUMINIUM TOWERS/SCAFFOLDS
SAFE ERECTION AND USE OF ALUMINIUM TOWERS/SCAFFOLDS PERSONNEL DIVISION Revised 2002 CONTENTS Page 1 INTRODUCTION 1 2 APPLICATION 1 3 ERECTION AND INSPECTION 1 4 ERECTION 1 4.1 Before erection of tower
More informationWalking/Working Surfaces
DEPAUL UNIVERSITY Walking/Working Surfaces Environmental Health & Safety May 2016 1 TABLE OF CONTENTS SECTION PAGE NO. 1.0 PURPOSE 2 2.0 RESPONSIBILITIES 2 2.1 Environmental Health and Safety 2.2 Facility
More informationSCAFFOLDING - Part 2 SELF INSPECTION CHECKLIST
OPTIONAL INFORMATION Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: SCAFFOLDING - Part 2 Instructions: This checklist covers some of the regulations issued
More informationBig Ox Energy Siouxland, LLC. Safety Management System. Authority: President
Issuing Dept: Safety Page: Page 1 of 5 Purpose The purpose of this program is to provide guidelines to Big Ox Energy - Siouxland LLC employees in the safe use of scaffolding, and to reduce the risk of
More information"SUPPORTED SCAFFOLDING SAFETY IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "SUPPORTED SCAFFOLDING SAFETY IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series "Quality Safety and Health Products, for Today...and Tomorrow" OUTLINE OF MAJOR
More informationFACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY AERIAL WORK PLATFORM POLICY 09/06/17 Last Revision
FACILITIES MANAGEMENT OFFICE OF ENVIRONMENTAL HEALTH AND SAFETY AERIAL WORK PLATFORM POLICY 09/06/17 Last Revision 1. Intent This program has been developed to reduce the risk of physical injury or property
More informationSafety on Heights: Our Policy
11/17/14 Safety on Heights: Our Policy Only volunteers over the age of 18 are allowed to work on heights of more than six feet off the ground. This includes all work on scaffolds. Only volunteers who are
More informationWalking-Working Surfaces
Walking-Working Surfaces Introduction Slips, trips and falls cause: the majority of general industry accidents 15 percent of all accidental deaths more fatalities than all other causes but motor vehicles
More informationNEBOSH International Certificate in Construction Safety and Health Unit ICC1 MANAGING AND CONTROLLING HAZARDS IN INTERNATINAL CONSTRUCTION ACTIVITIES
NEBOSH International Certificate in Construction Safety and Health Unit ICC1 MANAGING AND CONTROLLING HAZARDS IN INTERNATINAL CONSTRUCTION ACTIVITIES element 10: WORKING AT HEIGHT - HAZARDS AND RISK CONTROL
More informationWalking-Working Working Surfaces. OSHA Office of Training and Education 1
Walking-Working Working Surfaces OSHA Office of Training and Education 1 Introduction Slips, trips and falls cause: the majority of general industry accidents 15 percent of all accidental deaths more fatalities
More informationWalking-Working Surfaces
Walking-Working Surfaces 29 CFR Part 1910 Subpart D Presented by: ETTA, OSH Division 919-807-2875 Objectives 29 CFR 1910, Subpart D In this course, we will discuss the following: Hazards Definitions General
More informationOCCUPATIONAL HEALTH AND SAFETY ACT SCAFFOLDING REGULATIONS
c t OCCUPATIONAL HEALTH AND SAFETY ACT SCAFFOLDING REGULATIONS PLEASE NOTE This document, prepared by the Legislative Counsel Office, is an office consolidation of this regulation, current to October 28,
More informationWalking & Working Surfaces / Back Safety and Ergonomics
Walking & Working Surfaces / Back Safety and Ergonomics 29 CFR 1910.21-30 29 CFR 1910.66-67 67 29 CFR 1926.450-454 454 29 CFR 1926.1050-1060 1060 Scope Federal regulations cover the rules for the design
More informationCourse 804. Scaffold Erection and Inspection
Scaffold Erection and Inspection This page intentionally blank OSHAcademy Study Guide Safe Scaffold Erection and Inspection No portion of this text may be reprinted for other than personal use. Any commercial
More informationScaffolding Practice
Health & Safety Scaffolding Practice Content Owner Custodian H&S Discipline Program COMS Document Number Manager, H&S Programs H&S Programs & Projects Health & Safety Scaffolding See COMS Standards CEN-EHS9552
More informationHANDING-OVER CERTIFICATE - SCAFFOLDING
HANDING-OVER CERTIFICATE - SCAFFOLDING Contractor : Site : Contractor. customername Site. Site name Date : Time : Erected by : Signature : Description of section handed over Job specification. description
More informationTANK REPAIRS INCLUDING SCRAP DISPOSAL SCAFFOLDING JOBS
:- 1. Erect Metallic Scaffolding (including supply of all Scaffolding materials like Pipes, Planks, Clamps, Pins, Ladder arrangements), wherever required inside / outside the Tanks etc. as per instructions
More informationWorkplaces must be kept clean, orderly, and sanitary. Workroom floors must be maintained as clean and dry as possible.
Section C.19 University of South Carolina Safety Program Guide WALKING AND WORKING SURFACES Introduction Occupational Safety and Health Administration (OSHA) CFR 1910 Subpart D Walking and Working Surfaces
More informationCLIMA AGR. Mobile Aluminium Tower with Climbing Frames 1450/850 Camlock Advanced Guardrail USER GUIDE
CLIMA AGR Mobile Aluminium Tower with Climbing Frames 1450/850 Camlock Advanced Guardrail USER GUIDE Contents Safety First Safety Checklist Quantity Schedules Assembly and Dismantling Procedure Toe Boards
More informationConstruction Site Safety
Construction Site Safety Half (1/2) Continuing Education Hour Course #OS101 Approved Continuing Education for Design Professionals (Professional Engineers, Land Surveyors, Architects, etc.) EZ-pdh.com
More informationSpan 300 Instruction Manual
Span 300 Instruction Manual DESIGNATION SPAN300 Double Width EN 1004 3 8/12 XXCD SPAN 300 Single Width EN 1004 3 8/8 XXCD CEN designation of this instruction manual EN 1298 IM en Rev-00 WARNING NEVER STAND
More informationScissor Lift Safety for Clients and Employees or ARS
ADVANCED RESOURCE SOLUTIONS INNOVATIVE SOLUTIONS FOR PROJECT SUCCESS Scissor Lift Safety for Clients and Employees or ARS Added 1/20/2017 Employees: Guidelines addressed in OSHA 1926.451; 1926.452(w);
More informationAerial and Scissor Lift
This document is intended to provide basic safety guidelines for the Physical Plant Department at Community College of Allegheny County. The information provided in this guide may vary by site. Version
More informationEffective Date: 14-March Table of Contents
Version: 2 Page: 1 of 10 Table of Contents 1.0 Introduction... 2 1.1 Purpose... 2 1.2 Scope... 2 1.3 Definitions... 2 2.0 Guarding of Floor Openings, Wall Openings and Holes... 3 2.1 Stairway Floor Openings...
More informationACE Jobsite Inspection Report Habitat for Humanity
For Internal Use Only Affiliate Name: Affiliate Address: Job Site Name: Job Site Address: Contact/Title: Phone: This report is the property of ACE USA and is for use only in conjunction with the sale of
More informationA-0312 ASSEMBLY GUIDE
760265-A-0312 ASSEMBLY GUIDE 1 Contents Section Contents Introduction Know Your MiTOWER Know Your MiTOWER s Components Know Your Kit List and Specifications Know Your Storage and Transport Pack Safety
More informationBOOM-SUPPORTED ELEVATING WORK PLATFORM PROGRAM
Page: 1 of 7 1.0 PURPOSE and APPLICABILITY 1.1 It is the policy of the University of Pennsylvania in coordination with the Office of Environmental Health and Radiation Safety to provide the University
More informationScaffold Instruction Manual
Scaffold Instruction Manual This booklet contains information on how to erect, stabilize, dismantle and maintain your MultiScaff aluminium scaffolding. Manufactured by: August 2014 Index Page Number Safety
More informationSpan 400 Instruction Manual
Span 400 Instruction Manual DESIGNATION SPAN 400 Double Width EN 004 3 8/2 XXCD SPAN 400 Single Width EN 004 3 8/8 XXCD CEN designation of this instruction manual EN 298 IM en Rev-00 WARNING NEVER STAND
More informationBritish Columbia Carpenter Apprenticeship Program
British Columbia Carpenter Apprenticeship Program Level 2 Line E Competency E-1 Use Ladders and Scaffolds 7960003552 Ordering Crown Publications, Queen s Printer PO Box 9452 Stn Prov Govt 563 Superior
More informationSCAFFOLD REQUIREMENTS
SCAFFOLD REQUIREMENTS Steingass Mechanical Contracting, Inc. 754 Progress Drive Medina, Ohio 44256 (330) 725-6090 SCAFFOLDS INTRODUCTION The Occupational Safety and Health Act under 29 CFR 1926 Subpart
More information1 Man Mobile Aluminium Tower System
1 Man Mobile Aluminium Tower System Euro one, quick assembly, one person aluminum mobile tower Easy to erect and dismantle by one person with the base unit forming a trolley for fast storage and transportation.
More informationSAFE WORK METHOD STATEMENT (SWMS)
ABN: 12 345 678 910 ACN: 123 456 789 Address: Your Company Address PH: Your Company Phone E: Your Company Email Web: Your Company Website PROJECT DETAILS: Project: SAFE WORK METHOD STATEMENT (SWMS) Area:
More informationSafe Work Procedure for installation of
Safe Work Procedure for installation of external cladding This procedure has been formulated to cover safe systems of work for the installation of external cladding. This instruction will be used to reduce
More informationDEPARTMENT OF LICENSING AND REGULATORY AFFAIRS CONSUMER AND INDUSTRY SERVICES DIRECTOR S OFFICE BUREAU OF SAFETY AND REGULATION
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS CONSUMER AND INDUSTRY SERVICES DIRECTOR S OFFICE BUREAU OF SAFETY AND REGULATION GENERAL INDUSTRY SAFETY AND HEALTH STANDARD GENERAL INDUSTRY SAFETY STANDARDS
More informationBoSS Climalite Camera and lighting tower
Contents Safety First Safety First Quantity Schedules Toeboard 2 9 13 33 INTRODUCTION Please read this guide carefully. Please note that diagrams are for illustrative purposes only. User guides are also
More informationSAFETY BOB S COMPREHENSIVE CONSTRUCTION SAFETY ORIENTATION
ERI Safety Videos DVDs, Digital Media & Custom Production 1315 SAFETY BOB S COMPREHENSIVE CONSTRUCTION SAFETY ORIENTATION Leader s Guide ERI Safety Videos SAFETY BOB S COMPREHENSIVE CONSTRUCTION SAFETY
More information(6) Crawl boards and ladders used for roof work shall be securely fastened over the ridge of the roof or be otherwise effectively anchored.
Newfoundland & Labrador - Terre-Neuve-et-Labrador Ladder Safety - Sécurité des échelles This material has been extracted from the Acts and Regulations of the Province to help students understand the subject.
More informationWalking Working Surfaces
Walking Working Surfaces Walking - Working Surfaces One of the biggest safety concerns related to walking and working surfaces is fall prevention. Falls cause the majority of general industry accidents
More informationScaffolds. (Owner: Personnel Safety Section Supervisor)
BTCP/BTRF Scaffolds (Owner: Personnel Safety Section Supervisor) Site Safety Standard No. 4130 Introduction Scope This standard covers general safe practices that must be followed in the erection and use
More informationManagement Plan for Walking/Working Surfaces & Fall Protection (29 CFR , 23, 66 App.C; 29 CFR ) ISD #535
Management Plan for Walking/Working Surfaces & Fall Protection (29 CFR 1910.22, 23, 66 App.C; 29 CFR 1926.502) ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9½ Street Rochester, MN
More informationWARNING. *All Tele-Tower manuals are available free from Telpro Inc. Call Customer Service at or if you need a copy.
Adjustable Wor k Platfor m M O D E L 11 7 7 E X T E N S I O N O P E R A T O R S M A N U A L WARNING Read and follow these warnings and the instructions that follow. Failure to do so may result in serious
More informationBASIC SCAFFOLDING KNOWLEDGE QUESTIONS
Garnsworthy Square 46, 62 & 64 Garnsworthy St Springvale rth Victoria 3171 Updated on 22/02/08 STC105 Name BASIC SCAFFOLDING KNOWLEDGE QUESTIONS THE PROFESSIONAL Scaffold Tools Scaffold Belts Couplers
More informationSUPPORTED SCAFFOLDING SAFETY
LEADER'S GUIDE 1500-LDG-E SUPPORTED SCAFFOLDING SAFETY Training for the OSHA SCAFFOLDING STANDARD "Quality Safety and Health Products, for Today...and Tomorrow" THE REGULATORY COMPLIANCE KIT VIDEO SERIES
More informationLayher. Aluminium Rolling Towers. Layher SuperKlaxTower. Instructions for Assembly and Use
Mobile access and working towers in accordance with: HD 1004; DIN 4422, Part 1 (Version 8/92) Working platform 2.8 x 2.8 m and 2.8 x 1.95 m Max. working height: in closed rooms 13.95 m, outdoors 10.0 m
More informationHILLSBOROUGH TOWNSHIP CODE ENFORCEMENT
HILLSBOROUGH TOWNSHIP CODE ENFORCEMENT SAMPLE GUIDE FOR RESIDENTIAL DECKS revised 7 16 Call before you dig! 1 800 272 1000 New Jersey One Call. Utility Mark Out. THIS GENERIC GUIDE IS NOT ALL INCLUSIVE
More informationSAFE WORK PROCEDURE: MOBILE ELEVATED WORK PLATFORMS (MEWP)
Rev: 01 Date: March 2017 Page: 1 of 8 SAFE WORK PROCEDURE: MOBILE ELEVATED WORK PLATFORMS (MEWP) A. OVERVIEW: Safe Work Procedures are crucial to preventing workplace injuries and accidents. Safe Work
More informationDemolition Safety!!!!
Sample Written Program For Your Company For Demolition Safety Provided By: P.O. Box 2136 Slidell, LA 70458 Phone: 985-781-1444 Fax: 985-718-4957 Email: info@se-safety.com Demolition Safety Program Purpose
More informationSection Subparts T. Cleveland State University Work Zone Safety and Efficiency Transportation Center. Demolition
Demolition 1926.252(a) Whenever materials are dropped more than 20 feet to any point lying outside the exterior walls of the building, an enclosed chute of wood, or equivalent material, shall be used.
More information4. Stationary scaffolds over 125 ft. in height and rolling towers over 60 ft. in height must be designed by a professional engineer.
Section C.16 University of South Carolina Safety Program Guide SCAFFOLDS Introduction University of South Carolina recognizes that the scaffold industry is considered "inherently dangerous". These guidelines
More informationSafety Policy and Procedure
Safety Policy and Procedure Policy Number: 030 Authorized By: The Cianbro Companies Alan Burton Title: Placing Concrete Effective Date: 10/01/94 Page 1 of 5 1 Status 1.1 Update of existing policy, effective
More informationSECTION ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck)
SECTION 13125 ELEVATED BLEACHERS (Angle Frame Semi-Closed Deck) PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationRISK BULLETIN. Walking & Work Surfaces: Floors, Stairs and Elevated Workstations Checklist DATE / / NAME SIGNATURE WALKWAYS YES NO ACTION ASSIGNED
RISK BULLETIN Walking & Work Surfaces: Floors, Stairs and Elevated Workstations Checklist DATE / / NAME SIGNATURE WALKWAYS Are aisles and passageways kept clear? Are aisles and walkways marked to separate
More informationDON T FALL FOR IT HUNTSMAN PNPP ADDRESSES 100% TIE-OFF POLICY
DON T FALL FOR IT HUNTSMAN PNPP ADDRESSES 100% TIE-OFF POLICY Corporate Is 100% tie-off required by your employer, when working from a scaffold? Why? What makes an employer think that 100% tie-off is safe?
More informationEXCEL MODULAR STANDARD SCAFFOLD COMPONENT TECHNICAL MANUAL
EXCEL MODULAR STANDARD SCAFFOLD COMPONENT TECHNICAL MANUAL EMSLC-TSM-1001 Engineering Approval: Lance Smith Manual Release Date: 04/25/2017 Release Authorization: ECN EMSLC-0191 Revision: AK TABLE OF
More informationThe original WACO RED premium frame scaffolding and shoring systems.
The original WACO RED premium frame scaffolding and shoring systems. 2 WACO Premium Frame Scaffolding and Shoring System Used by thousands of the industry s top contractors and professionals, Waco Red
More informationTABLE OF CONTENTS PART 10 CONSTRUCTION AND BUILDING SAFETY
TABLE OF CONTENTS PART 10 CONSTRUCTION AND BUILDING SAFETY Page DEFINITIONS...10-1 GENERAL...10-1 FORMWORK AND SHORING...10-2 STRUCTURAL FRAMEWORK...10-2 BUILDING STRUCTURES...10-3 ROOFING...10-4 HOT TAR
More informationScaffold Safety in the Construction Industry
Scaffold Safety in the Construction Industry Introduction 1 Summary and Explanation of the Regulations 4 Use of Scaffolds 19 Fall Protection 22 Falling Object Protection 28 Requirements for Specific Types
More informationSPECIFICATION SECTION 05515: LADDERS O Keeffe s Aluminum Ladders
Welcome to the O Keeffe s Guide Specification System prepared as an aid to specify in preparing written construction documents. For specification assistance with specific product applications, please contact
More informationCHAPTER 42 FORMWORK 42 FORMWORK. Definitions. Introduction
CHAPTER 42 FORMWORK 42 FORMWORK Definitions The following definitions are used in the forming industry. Some terms may be used by other trades as well, but their meanings may be different from these depending
More informationCHAPTER 21 SCAFFOLDS 21 SCAFFOLDS. Hazards. Climbing Up and Down. Planks Sliding Off or Breaking. Improper Loading or Overloading
CHAPTER 21 SCAFFOLDS 21 SCAFFOLDS More than half of scaffold incidents in Ontario construction are falls. Several fatalities are also related to scaffolds each year. The number and severity of injuries
More informationFigure 5 - A shoring tower is made by assembling end frames with diagonal braces
Figure 5 - A shoring tower is made by assembling end frames with diagonal braces Figure 6 shows shoring towers being used in the construction of the new Computer Science building at the University of Washington
More informationScaffolding Glossary of Terms A
Scaffolding Glossary of Terms A ACCESS PLATFORM: A platform that gives access to and from places of work to persons, materials and equipment. ACCESSORY: A fitting that is able to be attached to a structural
More information