EDGEWATER, FLORIDA JUNE 14, 2010

Size: px
Start display at page:

Download "EDGEWATER, FLORIDA JUNE 14, 2010"

Transcription

1 SECTION STO QUIK GOLD SOFFIT SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. Sto Quik Gold Soffit system consisting of base coat, reinforcing mesh and finish coat applied to glass mat faced gypsum board in soffits, and ceilings. B. Related Sections: 1.3 SUBMITTALS 1. Section Gypsum Sheathing A. Product Data: For each type of product indicated. B. Shop Drawings: Show locations and installation of control and expansion joints including plans, elevations, sections, details of components, and attachments to other work. C. Samples for initial selection in the form of manufacturer s sample boards for finish texture selections consisting of actual units or sections of units at least 12 inches square showing the full range of textures available. D. Product Test Reports: Provide test report indicating stucco system is tested as a component of cold-formed metal framing system and gypsum sheathing capable of resisting positive and negative wind loads as indicated for this project and wind load pressures as defined by ASCE 7 and in accordance with the current Florida Building Code. 1.4 DESIGN REQUIREMENTS A. Design for maximum allowable system deflection, normal to the plane of the soffit, of L/360. B. Design for wind load in conformance with code requirements. C. Prevent the accumulation of water behind the finish system, either by condensation in the soffit or leakage through other components of construction, by proper design and detailing of the soffit and related construction. STO QUIK GOLD SOFFIT SYSTEM

2 D. Design minimum 1/2 inch wide expansion joints in the system where they exist in the substrate or supporting construction, at a minimum of every 30 feet (up to a maximum area of 900 sq. ft.), and where the system adjoins dissimilar construction or materials. F. Design minimum 1/4 inch wide perimeter sealant joints at penetrations through the system (lights, vents, etc.). G. Specify compatible backer rod and sealant, or suitable accessories for system terminations or joints. 1.5 QUALITY ASSURANCE A. Manufacturer requirements 1. System manufacturer for a minimum of twenty five (25) years. 2. Manufacturing facilities ISO 9001:2000 Certified Quality System. B. Contractor requirements 1. Engaged in application of the Sto Quik Gold Finish System for Soffits or similar systems for a minimum of three (3) years. 2. Knowledgeable in the proper use and handling of Sto materials and possessing certificate of completion of Sto on-line application test. 3. Employ skilled mechanics who are experienced and knowledgeable in plastering application for soffits, and familiar with the requirements of the specified work. 4. Successful completion of minimum three (3) projects of similar size and complexity to the specified project. 5. Provide the proper equipment, manpower and supervision on the job site to install the system in compliance with Sto's published specifications and details and the project plans and specifications. 1.6 DELIVERY, STORAGE AND HANDLING A. Deliver all materials in their original sealed containers bearing manufacturer's name and identification of product. B. Protect coatings (pail products) from freezing and temperatures in excess of 90 F (32 C). Store away from direct sunlight. C. Protect portland cement based materials (bag products) from moisture and humidity. Store under cover and off the ground in a dry location. D. Store cement board materials inside and protected from damage by the elements. Protect ends, edges, and faces of cement boards from damage 1.7 PROJECT/SITE CONDITIONS A. Maintain ambient and surface temperatures above 40 F (4 C) during application and for 24 hours after set of base coat and finish materials. STO QUIK GOLD SOFFIT SYSTEM

3 B. Provide supplementary heat for installation in temperatures less than 40 F (4 C) such that temperatures are maintained as in 1.08A. Prevent concentration of heat on the uncured waterproofing/air barrier, base coat and finish coat and vent fumes and other products of combustion to the outside to prevent contact with the waterproofing/air barrier, base coat and finish coat C. Provide protection of surrounding areas and adjacent surfaces from application of materials. 1.8 WARRANTY A. Provide manufacturer's standard warranty. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Approved manufacturer: Sto Corp. 2.2 ACCESSORIES A. Corner bead, casing bead, starter track, expansion and control joint accessories. All accessories shall meet the requirements of ASTM C 1063 and its referenced documents. Accessories shall be vinyl (ASTM D 1784) as selected by architect or designer. 2.3 SHEATHING A. Glass Mat Faced Gypsum Board complying with ASTM C 1177 as specified in Section BASE COAT A. Sto Primer/Adhesive-B one-component polymer modified cement based factory blend base coat with less than 33% portland cement content by weight. 2.5 REINFORCING MESHES A. Standard Mesh 1. Sto Mesh--nominal 4.5 oz./yd 2 symmetrical, interlaced open-weave glass fiber fabric made with alkaline resistant coating for compatibility with Sto materials B. Specialty Meshes 1. Sto Detail Mesh--nominal 4.2 oz/yd 2 flexible, symmetrical, interlaced glass fiber fabric, with alkaline resistant coating for compatibility with Sto materials STO QUIK GOLD SOFFIT SYSTEM

4 2.7 PRIMER A. Primer as recommended by Sto Corp. for specified system: Sto Primer Sand acrylic based tinted primer for roller application. 2.8 FINISH COAT A. Acrylic-based silicone enhanced, weatherproofing colored coating: Single component acrylic-based coating, containing acrylic polymer, and colored pigments. Product shall comply with the following: 2.9 ACCESSORIES StoSilco Shield, as manufactured by Sto Corp., 3800 Camp Creek Parkway, Building 1400, Suite 120, Atlanta, Georgia Performance and Physical Properties: Meet or exceed the following values for material cured at 73 degrees F (23 degrees C) and 50 percent relative humidity (unless otherwise specified). a. Application: Spray, roller, or brush. b. Working Time: minutes, depending on ambient conditions. c. Tensile Strength: 1450 psi (10.0 MPa), minimum. ASTM D 412 d. Flexibility Mandrel Bend: No cracking at -14 degrees F (-26 degrees C), ASTM D 522. e. Moisture Resistance: No defects attributable to adhesion, discoloration, blistering, cracking, flaking, ASTM D 2247, 14 day exposure. f. Mold Resistance: No Mold Growth at 90 days, ASTM D 3273 g. Adhesion to Concrete: 305 psi (2.07 MPa), ASTM D 4541 h. Water Vapor Permeability: 48 perms (2750 ng/pa.s.m2) tested at 5 dry mils, applied in one coat, and 42 perms (2400 ng/pa.s.m2) tested at 9 dry mils, applied in two coats, ASTM E 96 wet cup method. i. VOC: 1.3 lb/gal (160 g/l), EPA 24 A. Corner bead, casing bead, starter track, expansion and control joint accessories. All accessories shall meet the requirements of ASTM C 1063 and its referenced documents. Accessories shall be vinyl (ASTM D 1784) as selected by architect or designer JOB MIXED INGREDIENTS A. Water clean and potable. B. Portland cement, ASTM C 150, Type I, Type II, or Type I-II MIXING A. Sto Primer Adhesive-B--Mix automatically using Sto s continuous mixer, or mix manually by adding one 50 lb. bag of Sto Primer/Adhesive-B to quarts of STO QUIK GOLD SOFFIT SYSTEM

5 clean, potable water in a clean mixing pail. Mix with a clean, rust-free electric drill and paddle. Allow to set approximately five minutes, adjust mix if necessary by adding up to 12 fl.oz. of water per bag, and remix to a uniform consistency. Avoid retempering after mixing of product. Do not exceed maximum amount of water in mix ratio. B. Sto Primer--mix with a clean, rust-free high speed mixer to a uniform consistency. C. Sto Finish --mix with a clean, rust-free high speed mixer to a uniform consistency. A small amount of water may be added to adjust workability. Limit addition of water to amount needed to achieve the finish texture. D. Do not use anti-freeze compounds or other additives. PART 3 EXECUTION 3.1 EXAMINATION A. Inspect sheathing surfaces for: 1. Contamination -- algae, chalkiness, dirt, dust, efflorescence, form oil, fungus, grease, laitance, mildew or other foreign substances. 2. Cracks -- measure crack width and record location of cracks. 3. Damage and deterioration. 4. Moisture content and moisture damage -- use a moisture meter to determine if the surface is dry enough to receive the coatings and record any areas of moisture damage. 5. Compliance with specification tolerances -- record areas that are out of tolerance (greater than 1/4 inch in 10-0 feet deviation in plane). B. Inspect sheathing application for compliance with manufacturer s requirements. C. Report deviations from the requirements of project specifications or other conditions that might adversely affect the installation to the General Contractor. Do not install Sto materials until deviations are corrected. 3.2 SURFACE PREPARATION A. Replace weather damaged sheathing and repair damaged or cracked surfaces. B. Level surfaces to comply with required tolerances. 3.3 INSTALLATION A. Accessory Installation 1. Install appropriate starter accessory. 2. Install appropriate casing bead accessories at system terminations (such as expansion or control joints, lights or vent strips, etc.) in accordance with locations indicated on architectural drawings. Maintain a gap of STO QUIK GOLD SOFFIT SYSTEM

6 minimum 1/4" between the accessory and the abutment to form a sealant joint. 3. Follow accessory manufacturer's instructions for accessory butt joints to maintain water tightness. 4. Provide expansion joints in sheathing at minimum intervals of 30 feet up to a maximum area of 900 square feet, wherever the system abuts dissimilar construction or an existing joint occurs in construction. Fit sheathing snugly into accessories prior to attachment. 5. Fasten surface mount accessories ( for example, casing beads and surface mount expansion joints) through the sheathing into framing at locations indicated on architectural drawings. Where necessary, level surfaces such as outside corners with appropriate leveling material to maintain plumbness and squareness. B. Base Coat Application 1. Apply base coat over the sheathing with proper spray equipment or a stainless steel trowel to a uniform thickness of approximately 1/16 inch. Apply base coat in strips of 40 inches and immediately embed reinforcing mesh into the wet base coat by troweling from the center to the edge of the mesh. Avoid wrinkles in the mesh. Overlap the mesh minimum 2-1/2 inches at mesh joints and stagger mesh overlaps minimum 8 inches from sheathing joints. 2. Where surface mount accessories are used, such as deep V expansion joint, overlap the mesh from the sheathing onto the perforated accessory flange (refer to details). 3. The mesh must be fully embedded so that no mesh color shows through the base coat when it is dry. Feather mesh overlaps to avoid reading the mesh through the finish coating. Allow base coat to thoroughly dry before applying primer or finish. C. Finish Coat Application 1. Apply finish directly over the base coat (or primed base coat) only after the base coat/primer has thoroughly dried. Apply the finish by spraying, or troweling with a stainless steel trowel, depending on finish specified. General rules for application of finishes are as follows: a. Avoid application in direct sunlight. b. Apply finish in a continuous application, always working to a wet edge. c. Weather conditions affect application and drying time. Hot or dry conditions limit working time and accelerate drying and may require adjustments in the scheduling of work to achieve desired results; cool or damp conditions extend working time and retard drying and may require added measures of protection against wind, dust, dirt, rain and freezing. Adjust work schedule and provide protection. d. Do not install finish on accessories. f. Do not install separate batches of finish side-by-side. STO QUIK GOLD SOFFIT SYSTEM

7 D. Sealant Installation PROTECTION g. Do not apply finish over irregular or unprepared surfaces, or surfaces not in compliance with the project specifications. 1. Seal all open joints in the system with appropriate sealant in accordance with sealant manufacturer s recommendations to prevent any water from getting into or behind the system. A. Provide protection of installed materials from water infiltration into or behind them. B. Provide protection of installed materials from dust, dirt, precipitation, freezing and continuous high humidity until they are fully dry. END SECTION STO QUIK GOLD SOFFIT SYSTEM

Sto Guide Specification No. F601S StoQuik Gold Finish System for Soffits and Ceilings

Sto Guide Specification No. F601S StoQuik Gold Finish System for Soffits and Ceilings Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com Sto Guide Specification No. F601S StoQuik Gold

More information

MANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION

MANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION STUC-O-FLEX - ELASTOMERIC ACRYLIC FINISH APPLICATION TO PORTLAND CEMENT PLASTER / CONCRETE RENDER MANUFACTURER S (SHORT FORM) SPECIFICATION / SECTION 09220-09 24 00 PART 1-GENERAL SCOPE: Manufacturer's

More information

SECTION CONCRETE AND MASONRY COATINGS

SECTION CONCRETE AND MASONRY COATINGS 80658 StoColor Texture - Coarse Textured Acrylic-Based, Vertical Above-Grade Exterior Wall Coating for New Concrete, Stucco, and Masonry Construction SECTION 099723 CONCRETE AND MASONRY COATINGS Sto Corp.

More information

Section COATING RESTORATION

Section COATING RESTORATION Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com 80658R StoColor Texture - Coarse Textured Acrylic-Based,

More information

PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960

PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 STUC-O-FLEX PERM-FLEX ASSEMBLY DIRECT APPLICATION TO CEMENTITIOUS SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary

More information

PERM-FLEX (JC) ASSEMBLY DIRECT APPLICATION TO CEMENT BOARD SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960

PERM-FLEX (JC) ASSEMBLY DIRECT APPLICATION TO CEMENT BOARD SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 STUC-O-FLEX PERM-FLEX (JC) ASSEMBLY DIRECT APPLICATION TO CEMENT BOARD SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION A. Provide all labor, materials and equipment

More information

ACF for Soffit Specifications

ACF for Soffit Specifications ACF for Soffit Specifications CSI SECTION 09 25 13 CSI SECTION 09 25 13 Acrylic Plastering SYSTEM OVERVIEW This overview is provided as an explanatory resource for the designer and specifier and is not

More information

RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION

RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION STUC-O-FLEX RENEW ELASTOMERIC ACRYLIC COATING (PAINT GRADE) MANUFACTURERS SPECIFICATION / SECTION 09 97 23 PART 1-GENERAL 1.00 SCOPE: Manufacturer's specifications containing the requirements necessary

More information

GigaCrete Specification PlasterMax. PlasterMax : Fire Rated Plaster for Direct Application over Cement Masonry Units (CMU) Interior Walls

GigaCrete Specification PlasterMax. PlasterMax : Fire Rated Plaster for Direct Application over Cement Masonry Units (CMU) Interior Walls GigaCrete Inc. 6775 Speedway Blvd. Suite M105 Las Vegas, NV 89115 Ph (702) 643-6363 Fax (702) 643 1453 www.gigacrete.com GigaCrete Specification PlasterMax PlasterMax : Fire Rated Plaster for Direct Application

More information

Direct Finish System for Soffits and Ceilings Only Senerflex lamina applications to soffits and ceilings

Direct Finish System for Soffits and Ceilings Only Senerflex lamina applications to soffits and ceilings Direct Finish System for Soffits and Ceilings Only Senerflex lamina applications to soffits and ceilings INTRODUCTION This specification has been assembled to enable the design professional to select or

More information

SECTION EXTERIOR INSULATION AND FINISH SYSTEM

SECTION EXTERIOR INSULATION AND FINISH SYSTEM SECTION 07240 EXTERIOR INSULATION AND FINISH SYSTEM PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Exterior insulation and finish wall system (EIFS) as shown on Drawings and as specified. 1.02 SYSTEM

More information

THERMAL-FLEX ICF INSULATED CONCRETE FORMS COATING ASSEMBLY TO ICF BLOCK MANUFACTURERS SPECIFICATIONS / SECTION STUC-O-FLEX PART 1 - GENERAL

THERMAL-FLEX ICF INSULATED CONCRETE FORMS COATING ASSEMBLY TO ICF BLOCK MANUFACTURERS SPECIFICATIONS / SECTION STUC-O-FLEX PART 1 - GENERAL STUC-O-FLEX THERMAL-FLEX ICF INSULATED CONCRETE FORMS COATING ASSEMBLY TO ICF BLOCK MANUFACTURERS SPECIFICATIONS / SECTION 07240 PART 1 - GENERAL 1.01 DESCRIPTION A. Provide all labor, materials and equipment

More information

COREV AMERICA MANUFACTURER S SPECIFICATION DIRECT-APPLIED EXTERIOR FINISH SYSTEM ON CEMENT BOARD

COREV AMERICA MANUFACTURER S SPECIFICATION DIRECT-APPLIED EXTERIOR FINISH SYSTEM ON CEMENT BOARD COREV AMERICA MANUFACTURER S SPECIFICATION DIRECT-APPLIED EXTERIOR FINISH SYSTEM ON CEMENT BOARD PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Corev America s Direct-Applied Exterior Finish System

More information

SECTION BRICK MASONRY ASSEMBLIES

SECTION BRICK MASONRY ASSEMBLIES PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Face brick. 2. Mortar and grout. 3. Ties and anchors. 4. Miscellaneous masonry accessories. 1.2 SUBMITTALS A. Product Data: For each type

More information

EDGEWATER, FLORIDA JUNE 14, 2010

EDGEWATER, FLORIDA JUNE 14, 2010 SECTION 09 2400 - PORTLAND CEMENT PLASTER PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION 07530CP EPDM MEMBRANE ROOFING

SECTION 07530CP EPDM MEMBRANE ROOFING PART 1 GENERAL 1.1 SUMMARY SECTION 07530CP EPDM MEMBRANE ROOFING A. Section includes: 1. Adhered membrane roofing and flashing 2. Mechanically fastened roof insulation 3. Walkway pads 1.2 ARCHITECTURAL

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: WATER RESISTIVE BARRIERS/WEATHER BARRIERS REPORT HOLDER: PAREX USA, INC.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: WATER RESISTIVE BARRIERS/WEATHER BARRIERS REPORT HOLDER: PAREX USA, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2045 Reissued 01/2017 This report is subject to renewal 01/2019. DIVISION: 07 00

More information

THERMAL-FLEX COATING ASSEMBLY TO INSULATION BOARD MANUFACTURERS SPECIFICATIONS / SECTION 07240

THERMAL-FLEX COATING ASSEMBLY TO INSULATION BOARD MANUFACTURERS SPECIFICATIONS / SECTION 07240 STUC-O-FLEX THERMAL-FLEX COATING ASSEMBLY TO INSULATION BOARD MANUFACTURERS SPECIFICATIONS / SECTION 07240 PART 1 - GENERAL 1.01 DESCRIPTION Provide all labor, materials and equipment necessary to install

More information

COOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No.

COOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No. SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Acrylitex Interior Texture and Coating Submittal Documentation

Acrylitex Interior Texture and Coating Submittal Documentation Acrylitex Interior Texture and Coating Submittal Documentation Project: Contractor: Installer: Supplier: John Wagner & Associates dba Grabber Construction Products 866-237-GRAB(4722) Distributor: Acrylic

More information

SECTION THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

SECTION THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 075423 - THERMOPLASTIC POLYOLEFIN (TPO) ROOFING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including Division 00 Bidding Requirements and other Division

More information

CSI SECTION Direct Applied Finish Systems

CSI SECTION Direct Applied Finish Systems CSI SECTION 07 24 23 Direct Applied Finish Systems SYSTEM OVERVIEW This overview in italics is explanatory for the designer and specifier and is not part of the specification that follows. Parex WaterMaster

More information

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings. SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

Insulating Concrete Form (ICF) Texture Finish

Insulating Concrete Form (ICF) Texture Finish 100% ACRYLIC TEXTURED COATINGS Insulating Concrete Form (ICF) Texture Finish MANUFACTURER SPECIFICATION SECTION 09960 CARRARA ICF TEXTURE FINISH PART I GENERAL 1.01 SUMMARY A. This document contains all

More information

SECTION Specification for Building Limes Specification For Building Sands from Natural Sources Methods of Tests for Paints.

SECTION Specification for Building Limes Specification For Building Sands from Natural Sources Methods of Tests for Paints. SECTION 09200 PART 1 - GENERAL 1.01 DESCRIPTION A. Extent of Work: The extent of lath and plaster work is shown on the drawings and in schedules and includes interior and exterior plaster work, and fibreglass

More information

BACKSTOP TM NT - Texture A high performance, water-resistive membrane and air barrier

BACKSTOP TM NT - Texture A high performance, water-resistive membrane and air barrier BACKSTOP TM NT - Texture A high performance, water-resistive membrane and air barrier Backstop NT - Texture Specifications DRYVIT SYSTEMS CANADA MANUFACTURER S SPECIFICATION SECTION 07240 BACKSTOP NT -

More information

Senergy Base Coats / Adhesives Fast setting dry-mix polymer adhesive. Product Bulletin

Senergy Base Coats / Adhesives Fast setting dry-mix polymer adhesive. Product Bulletin Senergy Base Coats / Adhesives Fast setting dry-mix polymer adhesive Product Bulletin Senergy Base Coats / Adhesives DESCRIPTION STANDARD is a 100% acrylic based product that is field mixed with Type I

More information

REPORT HOLDER: GREENMAKER INDUSTRIES, LLC 697 OAKWOOD AVENUE WEST HARTFORD, CONNECTICUT EVALUATION SUBJECT: DECOPLAST DDARS NOTCHED

REPORT HOLDER: GREENMAKER INDUSTRIES, LLC 697 OAKWOOD AVENUE WEST HARTFORD, CONNECTICUT EVALUATION SUBJECT: DECOPLAST DDARS NOTCHED 0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3428 Reissued 07/2017 This report is subject to renewal 07/2019. DIVISION: 07 00

More information

3910 E. McKinney Denton, TX P.O. Box Dallas, TX EZ WALL CONCENTRATE, INC

3910 E. McKinney Denton, TX P.O. Box Dallas, TX EZ WALL CONCENTRATE, INC EZ Spread Coarse Sand Description EZ Spread is the perfect material for small projects and repairs. This factory prepared blend of portland cement proprietary additives, and sand. EZ Spread is designed

More information

Jewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION

Jewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION SEPTEMBER 2016 Jewel Stone Decorative Concrete Overlay System MANUFACTURER S IFICATION 09 62 81 Part 1 GENERAL 1.1 RELATED SECTIONS.1 Specification 03 30 00 Cast-in-Place Concrete.2 Specification 09 70

More information

Chevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES

Chevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.

SECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars. (Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications

More information

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: STO CORP.

DIVISION: THERMAL AND MOISTURE PROTECTION SECTION: DIRECT-APPLIED FINISH SYSTEMS REPORT HOLDER: STO CORP. 0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-2536 Reissued 08/2016 This report is subject to renewal 08/2018. DIVISION: 07 00 00 THERMAL

More information

TOPCOAT Restoration Specifications Structural Concrete

TOPCOAT Restoration Specifications Structural Concrete TOPCOAT Restoration Specifications Structural Concrete Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications Structural Concrete

More information

THIRD PARTY INSPECTION GUIDELINES FOR OWNERS AND GENERAL CONTRACTORS/CONSTRUCTION MANAGERS DS150

THIRD PARTY INSPECTION GUIDELINES FOR OWNERS AND GENERAL CONTRACTORS/CONSTRUCTION MANAGERS DS150 THIRD PARTY INSPECTION GUIDELINES FOR OWNERS AND GENERAL CONTRACTORS/CONSTRUCTION MANAGERS DS150 SECTION ONE A. Objective The objective of this guide is to provide Owners and General Contractors/Construction

More information

Guideline Specification ACRYMAX ARS-1-C Reinforced Composite Elastomeric Membrane System for Concrete Roofs Fluid-Applied Roofing

Guideline Specification ACRYMAX ARS-1-C Reinforced Composite Elastomeric Membrane System for Concrete Roofs Fluid-Applied Roofing 221 Brooke Street Media, PA 19063 610-566-7470 Fax 610-891-0834 Website www.acrymax.com e-mail info@acrymax.com This document is intended to provide guidelines for the proper specification and application

More information

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS PART 1 - GENERAL 1.1 DESCRIPTION SECTION 07 24 00 1. Use this section only for NCA projects. 2. Detail wall section, base edge, expansion and control joint conditions for each system. Show locations of

More information

SECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION

SECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION SECTION 093000 - SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing, vapor retarder, and crack isolation in conjunction

More information

1.4 ASSEMBLY DESCRIPTION

1.4 ASSEMBLY DESCRIPTION CSI SECTION 07 24 00 Insulation & Finish System (EIFS) - Class PB SYSTEM OVERVIEW The Insul-Flex Standard System is a Class PB EIF System qualified for use on noncombustible construction, combustible non-residential

More information

CSI SECTION Insulation & Finish System - Class PB PART 1 - GENERAL

CSI SECTION Insulation & Finish System - Class PB PART 1 - GENERAL CSI SECTION 07 24 00 Insulation & Finish System - Class PB SYSTEM OVERVIEW The Standard System is a Class PB EIF System qualified for use on noncombustible construction, combustible non-residential construction,

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products SECTION 09 05 61.13 MOISTURE VAPOR EMISSION CONTROL PART 1 - GENERAL 1.1 RELATED DOCUMENTS

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,

More information

***********************************************************************************

*********************************************************************************** AQUAFIN-2K/M Two-Component Cement-based Acrylic-based Waterproofing GUIDE AQUAFIN, Inc. SPECIFICATION PART 1 - GENERAL 1.1 SECTION INCLUDES SECTION 07 16 14 ACRYLIC MODIFIED (FLEXIBLE) CEMENTITIOUS WATERPROOFING

More information

SECTION SANDSTONE RESTORATION

SECTION SANDSTONE RESTORATION SECTION 04 01 40.91 - SANDSTONE RESTORATION Part 1 GENERAL 1.1 SUMMARY OF WORK A. For repairing and patching of sandstone. B. Related Sections 1. Section 01351 Special Procedures for Historic Treatment

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

KOSTER AMERICAN CORPORATION

KOSTER AMERICAN CORPORATION Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General

More information

Gold Bond BRAND Gypsum Sheathing

Gold Bond BRAND Gypsum Sheathing BRAND 09 06 29 16 00/NGC 43/NGC brand is a moisture-resistant sheathing installed on the outside of exterior framing as a substrate for exterior claddings. It is manufactured with a treated water-resistant

More information

A. Submit product data sheets and literature verifying physical properties of materials.

A. Submit product data sheets and literature verifying physical properties of materials. I. GENERAL ACRYSHIELD ROOF MANAGEMENT SYSTEM Installation Guide Specification For Preserving EPDM Roofs 07500 Saving Money, Safeguarding the Environment One Roof at a Time. 1.01 SUMMARY A. Provide labor,

More information

Application Instructions for Dryvit Backstop NT For Use Beneath Claddings Other Than Dryvit EIFS

Application Instructions for Dryvit Backstop NT For Use Beneath Claddings Other Than Dryvit EIFS Application Instructions for Dryvit Backstop NT For Use Beneath Claddings Other Than Dryvit EIFS CHECKLIST PRIOR TO THE INSTALLATION OF BACKSTOP NT - SMOOTH AND TEXTURE Project Conditions Maximum storage

More information

ERSYSTEM ONESTEP PLUS

ERSYSTEM ONESTEP PLUS 1 DG0047-A 05/2017 AGED (EPDM, TPO, CSPE-HYPALON, PIB) SINGLE-PLY (THERMOSET) MEMBRANE RESTORATION SYSTEM APPLICATION SAMPLE DESIGN GUIDELINE ERSYSTEM ONESTEP PLUS ITW POLYMERS SEALANTS NORTH AMERICA,

More information

SECTION THROUGH-PENETRATION FIRESTOP SYSTEMS

SECTION THROUGH-PENETRATION FIRESTOP SYSTEMS SECTION 07841 - THROUGH-PENETRATION FIRESTOP SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide

More information

TOPCOAT System Specifications Corrugated Transite Panels

TOPCOAT System Specifications Corrugated Transite Panels TOPCOAT System Specifications Corrugated Transite Panels Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT System Specifications Corrugated Transite

More information

DuROCK InsulROCK EIFS

DuROCK InsulROCK EIFS FEBRUARY 2017 DuROCK InsulROCK EIFS Exterior Insulation Finish System for Commercial and High Rise Construction MANUFACTURER S IFICATION 07 24 13 PART 1 GENERAL 1.1. RELATED SECTIONS 1.1.1. Specification

More information

FIVE STAR PRODUCTS, INC. (800)

FIVE STAR PRODUCTS, INC.  (800) FIVE STAR PRODUCTS, INC. www.fivestarproducts.com (800) 243-2206 1 of 12 DESIGN-A-SPEC GUIDELINES FIVE STAR STRUCTURAL CONCRETE V/O CONTENTS PART A - GENERAL CONDITIONS PART B - MATERIAL SPECIFICATIONS

More information

RESILIENT FLOORING: Hot and Heavy - Secoya

RESILIENT FLOORING: Hot and Heavy - Secoya 160 South Industrial Blvd. Calhoun, GA 30701 Section 096519 RESILIENT FLOORING: Hot and Heavy - Secoya This document is intended as a suggested guide for editing your architectural guide specification.

More information

SPECIFICATION GUIDELINE

SPECIFICATION GUIDELINE SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification

More information

A. Meet at Project site <insert number> days before starting installation.

A. Meet at Project site <insert number> days before starting installation. SECTION 074643 - COMPOSITION SIDING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Engineered wood cladding. 2. Soffit panels. 3. Trim and fascia. 4. Sealant. 5. Weather barrier. 6. Flashing. 1.2

More information

DIVISION 9 FINISHES Section Floor Finishes

DIVISION 9 FINISHES Section Floor Finishes Spec Component: SC-032-0807 Supersedes: SS-032-0601 DIVISION 9 FINISHES Section 09600 Floor Finishes Part 1 - General 1.01 Summary A. This specification describes the application of a waterproofing, slip

More information

CONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008

CONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008 SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION CONCRETE PAVING SLABS SET IN MORTAR

SECTION CONCRETE PAVING SLABS SET IN MORTAR SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints

More information

EXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD

EXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,

More information

SECTION ALUMINUM WINDOWS

SECTION ALUMINUM WINDOWS SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required

More information

1. Division 09 Section "Rough Carpentry."

1. Division 09 Section Rough Carpentry. GREENSPOINT AND LAUDER RD. EC/PRE-KlK PAGE 1 SECTION 096400 - WOOD FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

A. Section includes surface preparation and the application of high-performance coating systems on the following substrates:

A. Section includes surface preparation and the application of high-performance coating systems on the following substrates: ILLINOIS STATE UNIVERSITY CORDOGAN, CLARK & ASSOCIATES, INC. WATTERSON DINING EXPANSION PROJECT 960 RIDGEWAY AVENUE NORMAL, ILLINOIS AURORA, ILLINOIS CCA PROJECT NUMBER: 14362 630-896-4678 BID SET JULY

More information

SPECIFICATION GUIDELINE

SPECIFICATION GUIDELINE Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section

More information

RESILIENT FLOORING: Select Step Wood

RESILIENT FLOORING: Select Step Wood 160 S. Industrial Blvd Calhoun, GA 30701 Section 096519 RESILIENT FLOORING: Select Step Wood This document is intended as a suggested guide for editing your architectural guide specification. Mohawk Group

More information

DESIGN GUIDELINE FLUID-APPLIED WATERPROOFING

DESIGN GUIDELINE FLUID-APPLIED WATERPROOFING DESIGN GUIDELINE FLUID-APPLIED WATERPROOFING (TO RESTORE EPDM MEMBRANES) PART 1 GENERAL 1.01 DESCRIPTION A. The scope of this design guideline is to describe the installation of the ALDOCOAT Silicone reflective

More information

SECTION ALUMINUM STORM WINDOWS

SECTION ALUMINUM STORM WINDOWS PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable

More information

SECTION FLUID-APPLIED VAPOR PERMEABLE MEMBRANE AIR BARRIER SYSTEM ASSEMBLY (August 2013)

SECTION FLUID-APPLIED VAPOR PERMEABLE MEMBRANE AIR BARRIER SYSTEM ASSEMBLY (August 2013) SECTION 07 27 20 FLUID-APPLIED VAPOR PERMEABLE MEMBRANE AIR BARRIER SYSTEM ASSEMBLY (August 2013) PART 1 GENERAL 1.01 SECTION INCLUDES A. Materials and installation methods supplementing a one-component

More information

SECTION RESILIENT SHEET FLOORING

SECTION RESILIENT SHEET FLOORING SECTION 09 65 16 RESILIENT SHEET FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1.

More information

POLYURETHANE FOAM SAMPLE DESIGN GUIDELINES URETHANE

POLYURETHANE FOAM SAMPLE DESIGN GUIDELINES URETHANE 1 DG0034-H 05/2017 POLYURETHANE FOAM SAMPLE DESIGN GUIDELINES URETHANE ITW POLYMERS SEALANTS NORTH AMERICA, INC. 111 S. Nursery Road. Irving, TX 75060 Tel: 972-438-9111 Fax: 972-554-3939 www.itwsealants.com

More information

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING

More information

Alply CLASSIC WALL Architectural Insulated Panel Wall System

Alply CLASSIC WALL Architectural Insulated Panel Wall System SECTION 07 42 13 INSULATED METAL WALL PANELS ALPLY Insulated Panels Alply CLASSIC WALL Architectural Insulated Panel Wall System PART 1 / GENERAL 1.1 SYSTEM DESCRIPTION A. Smooth, non-embossed steel, insulated

More information

SECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board

SECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board SECTION 09260 GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard

More information

SECTION CAST-IN-PLACE CONCRETE

SECTION CAST-IN-PLACE CONCRETE SECTION 03300 CAST-IN-PLACE CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. The Contractor shall furnish all work and materials, including cement, sand and coarse aggregate, water, admixtures, curing

More information

Sto Guide Specification S6500 StoPowerwall ExtraSeal Air and Moisture Barrier with Direct Applied Stucco

Sto Guide Specification S6500 StoPowerwall ExtraSeal Air and Moisture Barrier with Direct Applied Stucco Sto Corp. 3800 Camp Creek Parkway Building 1400, Suite 120 Atlanta, GA 30331 Tel: 404-346-3666 Toll Free: 1-800-221-2397 Fax: 404-346-3119 www.stocorp.com Sto Guide Specification S6500 StoPowerwall ExtraSeal

More information

CSI SECTION

CSI SECTION Monobase BC- Colored Cement Finish Stucco Assemblies Specification CSI SECTION 09 24 00 CSI SECTION 09 24 00 PORTLAND CEMENT PLASTER Sider-Crete- Monobase BC (Concentrated fiber reinforced base coat) Cement

More information

SECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM

SECTION LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM Page 1 of 6 SECTION 08 32 20 LAGUNA SERIES TOP HUNG SLIDING DOOR SYSTEM USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED GLASS SLIDING DOORS. SECTION INCLUDES OVERHEAD SLIDING TUBE ASSEMBLY, MOUNTING

More information

DIVISION 3 - CONCRETE Section Concrete Rehabilitation

DIVISION 3 - CONCRETE Section Concrete Rehabilitation Spec Component: SC-102-03/10 SikaRepair 224 DIVISION 3 - CONCRETE Section 03730 - Concrete Rehabilitation Part 1 General 1.01 Summary A. This specification describes the patching or overlay of interior

More information

REPORT HOLDER: COREV AMERICA BRITTMOORE PARK DRIVE HOUSTON, TEXAS EVALUATION SUBJECT:

REPORT HOLDER: COREV AMERICA BRITTMOORE PARK DRIVE HOUSTON, TEXAS EVALUATION SUBJECT: 0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2000 Reissued 02/2017 This report is subject to renewal 02/2019. DIVISION: 07 00 00 THERMAL

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing

More information

TOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets

TOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets TOPCOAT Restoration Specifications Fiberglass & MB Granulated Cap Sheets Updated: 1/11 Quality You Can Trust From North America s Largest Roofing Manufacturer! www.gaf.com TOPCOAT Restoration Specifications

More information

by Rollfab Metal Products

by Rollfab Metal Products by Rollfab Metal Products SECTION 07460 ALUMINUM SIDING AND SOFFITS PART 1 GENERAL 1.2 RELATED SECTIONS 1.3 REFERENCES A. SECTION INCLUDES B. Aluminum Siding. C. Aluminum Soffits. D. Aluminum trim and

More information

SECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof

SECTION MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof SECTION 07550 MODIFIED BITUMINOUS MEMBRANE ROOFING Peel & Roof This section is based on the products of MFM Building Products Corp., which is located at: 525 Orange St. P. O. Box 340 Coshocton, OH 43812

More information

Rust-Oleum Industrial Brands Specification

Rust-Oleum Industrial Brands Specification Rust-Oleum Industrial Brands Specification Coating Specification for Rust-Oleum Virtual Solutions Coating Solution 2 A solvent based coating system High Performance 9100/9800 System DTM Epoxy Mastic/DTM

More information

PRODUCT SPECIFICATIONS

PRODUCT SPECIFICATIONS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: High density cast resin architectural products, including columns, panels, caps, bases, trim elements and balustrade systems. Specifier Note: Article below

More information

GUIDE SPECIFICATION: DUCT LINER

GUIDE SPECIFICATION: DUCT LINER GUIDE SPECIFICATION: DUCT LINER This specification guide includes thermal & acoustical insulation for ductwork and air handling systems. This section is based on the format recommended by MICA (Midwest

More information

Acceptable Floor Substrates: Concrete, cured mortar bed, plywood, and backer board.

Acceptable Floor Substrates: Concrete, cured mortar bed, plywood, and backer board. SECTION 093000 - SHEET MEMBRANE WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing and vapor retarder, in conjunction with tile and dimension stone installations.

More information

SECTION SIMULATED STONE MASONRY

SECTION SIMULATED STONE MASONRY Concrete Wall System Specifications PART 1 GENERAL 1.01 SECTION INCLUDES SECTION SIMULATED STONE MASONRY A. Construction of textured and colored formed concrete surfaces using simulated stone masonry molds

More information

MDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls

MDC MicroTex Eggshell Micro-Textured Ceramic Coating for Walls MicroTex Eggshell Micro-Textured Ceramic Coating for Walls Specification Guide 95: 9770 Special Wall Finishes 88: 9800 Special Coatings Part 1 General 1.01 SUMMARY A. This section specifies the furnishing

More information

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE

ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE ARCHITECTURAL GUIDE SPECIFICATIONS - DESCRIPTIVE MANNINGTON COLORFIELDS SHEET RUBBER FLOORING Section 09 65 16 Sheet rubber Flooring (Thermoset Rubber) Created May 2012 Mannington Mills, Inc. P. O. Box

More information

SECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM

SECTION SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM PART 1- GENERAL 1.1 SUMMARY A. Section Includes: SECTION 084523 - SLOPED TRANSLUCENT METAL SKYLIGHT SYSTEM 1. Flat factory prefabricated structural insulated translucent sandwich panels; with glazed endwalls.

More information

ACF for NuTech Specifications

ACF for NuTech Specifications ACF for NuTech Specifications CSI SECTION 09 25 13 CSI SECTION 09 25 13 Acrylic Plastering SYSTEM OVERVIEW This overview is provided as an explanatory resource for the designer and specifier and is not

More information

Guideline Specifications

Guideline Specifications Page 1 of 7 PART 1 Guideline Specifications Exterior Aluminum/Composite Wall Panels GENERAL ARROWHEAD 508 SYSTEM Pressure Equalized Rainscreen SECTION 07410 1.01 SUMMARY A. Work of this section included

More information

Signature Series 5 Lap SECTION ALUMINUM WINDOWS

Signature Series 5 Lap SECTION ALUMINUM WINDOWS Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this

More information

PG 9600 HIGH SOLIDS SILICONE ROOF COATING

PG 9600 HIGH SOLIDS SILICONE ROOF COATING WARRANTY INSTALLATION GUIDE SPECIFICATION FOR RESTORATION OF EXISTING SINGLE-PLY ROOFS (20 YEAR WARRANTY) PART 1 GENERAL 1.01 SUMMARY A. PG 9600, manufactured by ProGuard Group, Inc., is a high solids,

More information

By CTS Cement Manufacturing Corp.

By CTS Cement Manufacturing Corp. CSI SECTION 03 60 00 GROUTING 03 62 00 NON-SHRINK GROUTING 03 62 13 NON-METALLIC NON-SHRINK GROUTING High Flow, Non-Metallic, Multi-Purpose, Cementitious, Non-Shrink Grout EDITOR NOTE: The following guideline

More information