SERIES /8 SINGLE HUNG (CW50)
|
|
|
- Jonah Smith
- 5 years ago
- Views:
Transcription
1 SERIES /8 SINGLE HUNG (CW50) SPECIFICATIONS I. GENERAL: Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this project as shown on the drawings and herein specified. Windows shall be the "Series 515" as manufactured by Thermal Windows, Inc., Tulsa, Oklahoma. The "Series 515" is a single hung with thermally improved frame and sash consisting of an operable, tilt lower sash and a fixed upper lite. The specifications and materials for the "Series 515" are as follows: II. PRODUCTS: Materials - Aluminum shall be of proper alloy for commercial window construction. All extruded sections shall be of T5 aluminum alloy. Frame - Main frame and sash members shall be a nominal thickness as required by ANSI/AAMA 101. Main frame shall be 2.625" in depth. Horizontal sash members shall be hollow extrusions. Main frames and sash members are to be extruded aluminum with a structural thermal barrier of high density low thermal conductivity polyurethane, poured and debridged. Locks - Shall consist of a cam latch at the interlocking meeting rail along with an independent spring loaded latch for the sash. Balances - Sash will be balanced by field adjustable spirally wound spring sash balances attached to the main frame by pivot sash shoes of nylon. Balances shall hold the sash stationary in any position along the full range of sash travel. Where weight of sash requires, double sash balances will be used. Balances shall meet the requirements of AAMA Weatherstripping - Shall be.250 polypile with mylar fins conforming to AAMA 701.2, Specification for Pile Weatherstrip. Weatherstripping shall be doubled at all points of contact of the sash and main frames and at the interlocking meeting rail. A dual vinyl bulb seal will be used at the sill. III. CONSTRUCTION: Assembly - Main frame shall be a mechanically joined construction. Corner joints should be "seam sealed" with a quality grade of sealant meeting the requirements of AAMA The sash shall be assembled with two screws at each corner. All screws at joints of sash and main frame shall be secured into integral screw ports. Glazing - Glass in the operable sash shall be factory glazed with a marine (wrap around) reusable vinyl glazing channel. The fixed upper lite shall be inside glazed, using a rigid vinyl glazing bead. The insulated glass units shall be.875" overall thickness with two panes of double strength glass, separated by a.625" air space for optimum insulation. All insulated glass units shall meet the requirements of the ASTM E 2190 specification, Class "A". Screens - Screen frame shall be of hollow extruded aluminum frames. Finish shall match the main frames and sash. Insect screening shall be fiberglass or aluminum wire secured with a vinyl spline. Screens shall be half length. Finish - Shall be a factory applied baked polyurethane powder coat finish meeting the requirements of AAMA 2604 for Pigmented Organic Coating on Extruded Aluminum. Refer to Colors and Finishes chart for examples. Bronze anodizing, clear anodizing and high performance AAMA 2605 finishes are optional. Operation - The lower sash is operable on the "Series 515" Single Hung window and will raise for ventilation. The lower sash is equipped with a release latch so that it will tilt in for cleaning and is removable from the interior for ease of maintenance. IV. PERFORMANCE: Structural - Shall meet the requirements of AAMA/WDMA/CSA 101/I.S.2/A440-08, CW-PG50 specification. Thermal - Shall meet the requirements of AAMA CRF 57 / 50. NFRC Shall meet the requirements of NFRC 100 and 200. Forced Entry - Shall meet the requirements for ASTM F588 Load Identification Grade 10. Sound Transmission Class - Shall meet the requirements of ASTM E90. Ratings vary depending upon glazing. See Product Selection Guide for summary. V. INSTALLATION: Qualifications - Installation shall be performed by skilled, experienced tradesmen. Units shall be installed plumb, level, square and shall be secured in accordance with detailed shop drawings. A non-hardening sealant compatible with aluminum shall be provided by the installer and applied in sufficient quantity to provide a weathertight seal between the window and surrounding construction. Installation Details - The window manufacturer shall submit complete installation details for the Architects approval. The drawings shall show elevations of windows, full size details of frame and vents, details of construction and anchorage of window. Pg. 20
2 SERIES /8 SINGLE HUNG (CW50) Typical Configurations (Scale: Half Size) See Accessories section for additional options Pg. 21
3 SERIES /8 SINGLE HUNG (CW50) Product Details (Scale: Full Size) Pg. 22
4 SERIES /8 SINGLE HUNG (CW50) Product Details (Scale: Full Size) Pg. 23
5 SERIES /4 SINGLE HUNG (CW50) SPECIFICATIONS I. GENERAL: Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this project as shown on the drawings and herein specified. Windows shall be the "Series 515" as manufactured by Thermal Windows, Inc., Tulsa, Oklahoma. The "Series 515" is a single hung with thermally improved frame and sash consisting of an operable, tilt lower sash and a fixed upper lite. The specifications and materials for the "Series 515" are as follows: II. PRODUCTS: Materials - Aluminum shall be of proper alloy for commercial window construction. All extruded sections shall be of T5 aluminum alloy. Frame - Main frame and sash members shall be a nominal thickness as required by ANSI/AAMA 101. Main frame shall be 3.250" in depth. Horizontal sash members shall be hollow extrusions. Main frames and sash members are to be extruded aluminum with a structural thermal barrier of high density low thermal conductivity polyurethane, poured and debridged. Locks - Shall consist of a cam latch at the interlocking meeting rail along with an independent spring loaded latch for the sash. Balances - Sash will be balanced by field adjustable spirally wound spring sash balances attached to the main frame by pivot sash shoes of nylon. Balances shall hold the sash stationary in any position along the full range of sash travel. Where weight of sash requires, double sash balances will be used. Balances shall meet the requirements of AAMA Weatherstripping - Shall be.250 polypile with mylar fins conforming to AAMA 701.2, Specification for Pile Weatherstrip. Weatherstripping shall be doubled at all points of contact of the sash and main frames and at the interlocking meeting rail. A dual vinyl bulb seal will be used at the sill. III. CONSTRUCTION: Assembly - Main frame shall be a mechanically joined construction. Corner joints should be "seam sealed" with a quality grade of sealant meeting the requirements of AAMA The sash shall be assembled with two screws at each corner. All screws at joints of sash and main frame shall be secured into integral screw ports. Glazing - Glass in the operable sash shall be factory glazed with a marine (wrap around) reusable vinyl glazing channel. The fixed upper lite shall be inside glazed, using a rigid vinyl glazing bead. The insulated glass units shall be.875" overall thickness with two panes of double strength glass, separated by a.625" air space for optimum insulation. All insulated glass units shall meet the requirements of the ASTM E 2190 specification, Class "A". Screens - Screen frame shall be of hollow extruded aluminum frames. Finish shall match the main frames and sash. Insect screening shall be fiberglass or aluminum wire secured with a vinyl spline. Screens shall be half length. Finish - Shall be a factory applied baked polyurethane powder coat finish meeting the requirements of AAMA 2604 for Pigmented Organic Coating on Extruded Aluminum. Refer to Colors and Finishes chart for examples. Bronze anodizing, clear anodizing and high performance AAMA 2605 finishes are optional. Operation - The lower sash is operable on the "Series 515" Single Hung window and will raise for ventilation. The lower sash is equipped with a release latch so that it will tilt in for cleaning and is removable from the interior for ease of maintenance. IV. PERFORMANCE: Structural - Shall meet the requirements of AAMA/WDMA/CSA 101/I.S.2/A440-08, CW-PG50 specification. Thermal - Shall meet the requirements of AAMA CRF 57 / 50. NFRC Shall meet the requirements of NFRC 100 and 200. Forced Entry - Shall meet the requirements for ASTM F588 Load Identification Grade 10. Sound Transmission Class - Shall meet the requirements of ASTM E90. Ratings vary depending upon glazing. See Product Selection Guide for summary. V. INSTALLATION: Qualifications - Installation shall be performed by skilled, experienced tradesmen. Units shall be installed plumb, level, square and shall be secured in accordance with detailed shop drawings. A non-hardening sealant compatible with aluminum shall be provided by the installer and applied in sufficient quantity to provide a weathertight seal between the window and surrounding construction. Installation Details - The window manufacturer shall submit complete installation details for the Architects approval. The drawings shall show elevations of windows, full size details of frame and vents, details of construction and anchorage of window. Pg. 24
6 SERIES /4 SINGLE HUNG (CW50) Typical Configurations (Scale: Half Size) See Accessories section for additional options Pg. 25
7 SERIES /4 SINGLE HUNG (CW50) Product Details (Scale: Full Size) Pg. 26
8 SERIES /4 SINGLE HUNG (CW50) Product Details (Scale: Full Size) Pg. 27
SERIES /8 HORIZONTAL SLIDING WINDOW (CW30)
SERIES 525 2-5/8 HORIZONTAL SLIDING WINDOW (CW30) I. GENERAL: SPECIFICATIONS Scope of Work - Furnish all necessary materials, labor and equipment for the complete installation of aluminum windows for this
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
SECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
4600 Series Specifications (Section 08520)
4600 Series Specifications (Section 08520) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for this project as
MARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
Heavy Commercial / Architectural Projected Windows Series L900T AW150
Heavy Commercial / Architectural Projected Windows Series L900T AW150 Section 08520...Aluminum Windows PART 1: WORK INCLUDED GUIDE SPECIFICATION A. The conditions of the contract and applicable sections
Section Aluminum Windows (M950/M950B Series Specifications)
Section 08520 - Aluminum Windows (M950/M950B Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows
Section Aluminum Windows (M-85 Series Specifications)
Section 08520 - Aluminum Windows (M-85 Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
CTB Commercial Aluminum Window
Technical Information Description The is thermally-broken for use in commercial construction. Basic models include horizontal slider, single hung and fixed picture windows. Units are mulled together with
T700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD)
T700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD) FEATURES 1.) Available Configurations -Single hung -Oriel style (optional) 2.) Main frame / Sash -Drop-in glazing
Series 660 Single Hung * Series 670 Double Hung Series 6600 Fixed ** Heavy Commercial Hung Thermal Window
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com IMPACT GRADE BLAST GRADE Series 660 Single Hung * Series 670 Double Hung Series 6600 Fixed ** 3 7 8 Heavy Commercial Hung Thermal Window
Section Aluminum Windows (2700 Model Specifications)
Section 08520 - Aluminum Windows (2700 Model Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
SECTION SERIES 200 DOUBLE-HUNG VINYL WINDOWS
SERIES 200 DOUBLE-HUNG VINYL WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Replacement Windows. 1. Double hung windows 1.2 RELATED SECTIONS A. Section 05450: Cold Formed Metal Framing. B. Section 06100:
Series HX32 Single Hung/Tilt Series FX32 Fixed 3 1/4" High Performance Thermal, Architectural Grade Windows
Windows Curtain Walls Entrances Storefronts Series HX32 Single Hung/Tilt Series FX32 Fixed 3 1/4" High Performance Thermal, Architectural Grade Windows HX32 High Performance thermal Single hung TILT Designed
Section Aluminum Windows (4500 Series Specifications)
Section 08520 - Aluminum Windows (4500 Series Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
Series SX45 Horizontal Slider Series FX45 Fixed 4 1/2" High Performance Thermal, Architectural Grade Windows
Windows Curtain Walls Entrances Storefronts Series SX45 Horizontal Slider Series FX45 Fixed 4 1/2" High Performance Thermal, Architectural Grade Windows SX45 High Performance thermal Horizontal sliding
Section Sliding Aluminum Framed Glass Doors (2500 Model Specifications)
Section 083213 - Sliding Aluminum Framed Glass Doors (2500 Model Specifications) I. GENERAL: SECTION 083213 SLIDING ALUMINUM- FRAMED GLASS DOORS 1.01 Scope of Work A. Furnish all necessary materials, labor,
3 7 8 Heavy Commercial Hung Thermal Window
Windows Curtain Walls Entrances Storefronts Series 680 Single Hung/Tilt Series 690 Double Hung/Tilt * Series 6600 Fixed * 3 7 8 Heavy Commercial Hung Thermal Window Configurations Single Hung/Single Tilt
SILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
MPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
TIE Aluminum Guide Spec: Thermally Improved Windows & Doors
TIE Aluminum Guide Spec: Thermally Improved Windows & Doors Thermally Improved Aluminum Windows (TIE) ALUMINUM WINDOWS - 08 51 13 With the thin lines that Milgard s TIE Aluminum Windows provide, they
SECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
Series 675 Double Hung Series 676 Double Hung Series 676HP Double Hung Series 6750 Fixed Heavy Commercial Hung Thermal Window
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com Series 675 Double Hung Series 676 Double Hung Series 676HP Double Hung Series 6750 Fixed Configurations Double Hung Beveled Glazing Double
SILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
WINDOW TECH SYSTEMS, INC.
SPECIFICATIONS The Wintech Series 6000 consists of 3 ¼ frame commercial aluminum windows with poured urethane thermal barriers. Model 6000 is a horizontal sliding window with a rating of HS-C50 and Model
WINDOW TECH SYSTEMS, INC. 3 ¼ HORIZONTAL SLIDING & FIXED ALUMINUM WINDOWS SPECIFICATIONS
SPECIFICATIONS The Wintech Series 6000 consists of 3 ¼ frame commercial aluminum windows with poured urethane thermal barriers. Model 6000 is a horizontal sliding window with a rating of HS C50 and Model
SECTION ALL ULTREX DOUBLE HUNG WINDOW
SECTION 08 54 13 ALL ULTREX DOUBLE HUNG WINDOW PART 1 GENERAL 1.1 SECTION INCLUDES A. All Ultrex double hung window complete with hardware, glazing, weather strip, insect screen and half screen, grillesbetween-the
SERIES 8520 AW-PG80-AP PROJECT-OUT AWNING WINDOW
PART 1 - GENERAL 1.1 SCOPE OF WORK SERIES 8520 AW-PG80-AP PROJECT-OUT AWNING WINDOW SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications
Section Aluminum Windows (2700 Model Specifications)
Section 08520 - Aluminum Windows (2700 Model Specifications) I. GENERAL: 1.01 Scope of Work A. Furnish all necessary materials, labor, and equipment for the complete installation of aluminum windows for
PRODUCT SPECIFICATION SERIES 5000T PUNCHED WINDOW THERMALLY BROKEN ALUMINUM CASEMENT/AWNING/ FIXED WINDOW
08 51 13 ALUMINUM WINDOWS PART 1 - GENERAL A high-quality thermally broken 3 ½ aluminum window designed for residential low, mid and high rise construction. 1.1 SUMMARY A. Section Includes: Aluminum Windows:
Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
SERIES 5500 H-HC60 DOUBLE-HUNG TILT WINDOW
SECTION 08 51 13 ALUMINUM WINDOWS PART 1 - GENERAL 1.1 SCOPE OF WORK A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
Model 8000 Double Hung H-C x 2311 (56 x 91 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
Model 2000 Single Hung H-HC x 2515 (60 x 99 )
Architect to edit the items in red. PART 1 - GENERAL 1.01 GENERAL PROVISIONS: A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work
Single Hung Windows. Architectural Manual. Overview. Components. Thermally Improved Aluminum Series Windows & Patio Doors
s Please also see: TI Aluminum Options Full Lifetime Warranty Overview The 1520 Series is designed as an inside slider (the bottom panel or vent slides inside the stationary panel). For the vent to open
4 1 2" Sliding Door WINDOW ELEVATIONS FEATURES OPTIONAL O-X SLIDING DOOR X-O SLIDING DOOR VER:
WINDOW ELEVATIONS 4 1 2" Sliding Door 1 1 3 4 5 5 4 3 2 1280 1280 2 1280-2 O-X SLIDING DOOR 1280-2 X-O SLIDING DOOR FEATURES 4-1/2" FRAME DEPTH 1" INSULATED GLASS HEAVY-DUTY LATCH HANDLE FIBERMESH LOCKING
SECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
Series 900 Horizontal Sliding Window
Protecting you from the elements AJ Manufacturing s insulated aluminum windows keep your building protected from all extremes of weather. During the scorching heat of summer or the frigid temps of winter,
6400 Series TRIPLE GLAZED THERMAL BREAK CHURCH WINDOWS America's finest custom windows MINIMUM 5 8" AIR SPACE 3 1 2" SCALE = FULL SIZE
Since 906 Series The Series is a heavy triple glazed church window incorporated into a " thermally broken frame. The thermal break is achieved with the use of Thermal Strip technology. Two different aluminum
SERIES 8000 AW-PG90-C CASEMENT OUTSWING WINDOW
PART 1 - GENERAL 1.1 SCOPE OF WORK SERIES 8000 AW-PG90-C CASEMENT OUTSWING WINDOW SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications
Series 8100 Horizontal Slider HS-C x 1524 ( 71 x 60 )
1.01 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract, and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
SERIES 2100 CW-PG60-FW FIXED WINDOW
PART 1 - GENERAL 1.1 SCOPE OF WORK SERIES 2100 CW-PG60-FW FIXED WINDOW SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated
Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 2900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
Series 3500 Thermal Series 3900 Fixed Thermal Architectural Grade Horizontal Sliding Window
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com IMPACT GRADE Series 3500 Thermal Series 3900 Fixed Thermal 3 1 4 Architectural Grade Horizontal Sliding Window Configurations XO OX XOX
SECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
SECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
SERIES 8510 AW-PG85-FW FIXED WINDOW
PART 1 - GENERAL 1.1 SCOPE OF WORK SERIES 8510 AW-PG85-FW FIXED WINDOW SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated
SERIES 5100 AW-PG100-FW FIXED WINDOW
PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
Model 4000-IM Single Hung H-C x 2300 (56 x 91 )
1.01 GENERAL PROVISIONS: PART 1 - GENERAL Architect to edit the items in red. A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work
Series 700 Series 7000 * 4 Heavy Commercial Roto-Vent Rotating Ventilator Window
Windows Curtain Walls Entrances Storefronts Series 700 Series 7000 * 4 Heavy Commercial Roto-Vent Rotating Ventilator Window Configurations Roto-Vent Fixed Series 700 and 7000 retain an AAMA Heavy Commercial
SERIES 6200 HS-HC60 HORIZONTAL SLIDING WINDOW
SECTION 08 51 13 ALUMINUM WINDOWS PART 1 - GENERAL 1.1 SCOPE OF WORK A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
Model 2000 IM Single Hung H-HC x 2500 (60 x 96 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
DOUBLE HUNG SERIES 860 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F. 50. Thermal U Value:.61. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com DOUBLE HUNG SERIES 860 AAMA/WDMA/CSA
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
HORIZONTAL SLIDER SERIES 600 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 600 AAMA/WDMA/CSA
PROJECT IN SERIES 1300 NARROW SIGHT LINE AAMA/WDMA/CSA 101/I.S.2/A Structural Performance:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT IN SERIES 1300 NARROW SIGHT
Vinyl Window Designs Ltd. 550 Oakdale Road Toronto, ON M3N 1W6 SPECIFICATIONS
Vinyl Window Designs Ltd. 550 Oakdale Road Toronto, ON M3N 1W6 DIVISION 08 / SECTION 08560, VINYL WINDOWS SPECIFICATIONS 1.0. Section includes: 1. All windows of the types and sizes as called for in this
Series 890-I Equa-Vu Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 890-I Equa-Vu 3 1 2 Heavy Commercial Projected Window Configurations Project-In Casement Inswing Fixed Series 890-I retains an AAMA Architectural Grade
Series 510-I Thermal Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 510-I Thermal 2-7 16 Heavy Commercial Projected Window Configurations Project-In Project-Out Casement Fixed Series 510-I retains an AAMA Architectural
TRUMAN STATE UNIVERSITY GREENWOOD SCHOOL WINDOW REPLACEMENT
SECTION 085200 - WOOD WINDOWS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
SERIES 1400 ATD-HC50 ARCHITECTURAL TERRACE DOOR
SECTION 08 11 16 ALUMINUM DOORS AND FRAMES PART 1 - GENERAL 1.1 SCOPE OF WORK A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
SPECIFICATION GUIDE SERIES 800 HEAVY PICTURE WINDOW
SERIES 800 HEAVY PICTURE WINDOW Page 1 of 6 SPECIFICATION GUIDE SERIES 800 HEAVY PICTURE WINDOW www.ramwindows.com RAM Windows Series 800 Heavy Picture window is a custom residential and commercial window
SINGLE HUNG SERIES 810 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.61. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com SINGLE HUNG SERIES 810 AAMA/WDMA/CSA
DOUBLE HUNG SERIES 3500 AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F.
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com DOUBLE HUNG SERIES 3500 AAMA/WDMA/CSA
PRODUCT SPECIFICATION SERIES 4500T THERMALLY BROKEN ALUMINUM SLIDING BALCONY DOOR
08 2 1 SLIDING ALUMINUM FRAMED GLASS DOOR PART 1 - GENERAL A high-quality thermally broken aluminum balcony sliding door designed for residential high rise construction. 1.1 SUMMARY A. Section Includes:
Series B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
Awning Windows Montecito New Construction Window
Awning Windows Montecito New Construction Window Full awning Double-top awning Double awning Double-bottom awning FULL DOUBLE BOTTOM/TOP DOUBLE AWNING - Min 1 3 1 4 Max 4 6 3 0 AWNING - Min 3 0 1 6 Max
Casement Windows Montecito New Construction Window
Casement Windows Montecito New Construction Window Full casement Double-bottom casement FULL DOUBLE/SINGLE DOUBLE CASEMENT - Min 1 6 1 0 Max 3 0 5 0 or 2 6 6 0 CASEMENT - Min 3 0 1 6 Max 6 0 5 0 or 5 0
SERIES 9000 AW-PG70-DAW DUAL ACTING WINDOW (TILT/TURN)
PART 1 - GENERAL 1.1 SCOPE OF WORK SECTION 08 51 13 ALUMINUM WINDOWS A. Furnish and install aluminum windows as shown in bid drawings and as per specifications stipulated in this section. B. Factory-installed
SECTION SLIDING PATIO DOORS. Display hidden notes to specifier by using Tools/Options/View/Hidden Text
SECTION 08260 SLIDING PATIO DOORS Display hidden notes to specifier by using Tools/Options/View/Hidden Text PART 1 GENERAL 1.1 SECTION INCLUDES A. Vinyl sliding patio doors (Spencer Walcott). 1.2 RELATED
Series Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 510 2-7 16 Heavy Commercial Projected Window Configurations Project-In Project-Out Casement Pivot Top-Hinged Fixed Series 510 retains an AAMA Architectural
CASEMENT PROJECT OUT SERIES 6400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 6400
CASEMENT PROJECT OUT SERIES 2400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 2 3/8
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 2400
HORIZONTAL SLIDER SERIES 700. Main Frame Depth: 2 3/4 Glazing Thickness (Maximum): 5/8 Thermal Break:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 700 Main
PROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
Sliding Patio Doors Brickmould Vinyl
TABLE OF CONTENTS Specifications... 7-2 QuickSpecGuide... 7-3 Elevations/Sizes: 1/8 Scale 2-WideSlidingPatioDoors... 7-4 GlazingOptions: 3 Scale... 7-5 Grille Patterns... 7-6 SectionDetails: 6 Scale...
Model 2000 BR Single Hung H-HC x 2500 (60 x 96 )
1.00 GENERAL PROVISIONS: PART 1 - GENERAL A. The Conditions of the Contract and all Sections of Division 1 are hereby made a part of this Section. B. Coordinate work with that of all construction contractors
2000/2100/2200 Series Heavy Commercial Sliding Patio Doors
2000/2100/2200 Series Heavy Commercial Sliding Patio Doors MANKO WINDOW SYSTEMS, INC. 800 HAYES DRIVE MANHATTAN, KANSAS 66502 PHONE: (800) 642-1488 (785) 776-9643 FAX: (800) 576-2656 (785) 776-9644 MANKO
TEST REPORT. Report No.: B Rendered to: MI WINDOWS AND DOORS, INC. Gratz, Pennsylvania
Architectural Testing TEST REPORT Report No.: B2133.01-109-47 Rendered to: MI WINDOWS AND DOORS, INC. Gratz, Pennsylvania PRODUCT TYPE: PVC Single Hung Window (Fin) SERIES/MODEL: 3540 SPECIFICATION: AAMA/WDMA/CSA
HORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA
HORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA
Milgard Quiet Line Series Vinyl Windows 3-Part Specification
GENERAL NOTES TO SPECIFIER: THIS SPECIFICATION SECTION HAS BEEN PREPARED TO ASSIST DESIGN PROFESSIONALS IN THE PREPARATION OF PROJECT OR OFFICE MASTER SPECIFICATIONS. IT FOLLOWS GUIDELINES ESTABLISHED
AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A AAMA TEST REPORT SUMMARY
AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 AAMA 910-93 TEST REPORT SUMMARY Rendered to: GIESSE NORTH AMERICA 2014 Holston Industrial Drive Blountville, TN 37617 PRODUCT TYPE: XO Sliding
PRODUCT SPECIFICATION THE 9500 SERIES FAMILY - SERIES 9502 / 9503 THERMALLY BROKEN ALUMINUM OUTSWING BALCONY DOOR
PART 1 - GENERAL 08 13 16 ALUMINUM DOORS (Outswing Aluminum-Framed Glass Doors) A high-quality thermally broken aluminum balcony outswing door designed for residential high rise construction. 1.1 SUMMARY
Operable / Fixed Skylight Milgard Aluminum Window
Skylight Operable / Fixed Skylight Milgard Aluminum Window The Series Skylight has been specifically designed to provide maximum thermal efficiency by incorporating a special polyurethane barrier between
Aluminum Windows and Doors
Aluminum Windows and Doors A Better Experience We re so much more than windows OUR MISSION: GETTING IT RIGHT EVERY TIME As one of the nation s largest suppliers of high-quality windows for existing and
PROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
Awning Windows Tuscany Vinyl Replacement Window
Awning Windows Tuscany Vinyl Replacement Window Full awning Double-top awning Double awning Double-bottom awning FULL DOUBLE BOTTOM/TOP DOUBLE AWNING - Min 1 3 1 4 Max 4 6 3 0 AWNING - Min 3 0 1 6 Max
Signature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A TEST REPORT SUMMARY. Rendered to:
AAMA/WDMA/CSA 101/I.S.2/A440-08 AAMA/WDMA/CSA 101/I.S.2/A440-05 TEST REPORT SUMMARY Rendered to: AluminTechno LLC. 12 Selitskog Street, Room 211 FEZ Minsk, Minsk District, Minsk Region 220075 Republic
CASEMENT PROJECT OUT SERIES 4400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 4400
GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM
1 GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials, and services to furnish and install VERSA SHIELD Window
SECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
Casement Windows Tuscany Vinyl Replacement Window
Casement Windows Tuscany Vinyl Replacement Window Full casement Double-bottom casement FULL SINGLE DOUBLE CASEMENT - Min 1 6 1 0 Max 3 0 5 0 or 2 6 6 0 CASEMENT - Min 3 0 1 6 Max 6 0 5 0 or 5 0 6 0 CASEMENT
FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4. Glazing Thickness (Maximum): 1
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A440-08
GUIDE SPECIFICATIONS - SECTION ALUMINUM WINDOWS Manko Window Systems Inc SERIES (Single Hung)
GUIDE SPECIFICATIONS - SECTION 085210 ALUMINUM WINDOWS Manko Window Systems Inc. 7041 SERIES (Single Hung) SECTION 085210 ALUMINUM WINDOWS (Single Hung) PART 1 GENERAL 1.01 SUMMARY A. Section Includes: