SECTION ALUMINUM ENTRANCES AND STOREFRONTS. A. Section Includes: Aluminum doors and window wall frames.
|
|
- Agatha Ursula Nicholson
- 5 years ago
- Views:
Transcription
1 SECTION ALUMINUM ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Aluminum doors and window wall frames. B. Related Sections: 1. Section Balanced Doors 2. Section Door Hardware 3. Section Glazing SUBMITTALS A. Submit product data, shop drawings and samples in accordance with Section Product Data: Submit 2 copies of Manufacturer's Specifications, recommendations and standard details for aluminum doors, and frames. 2. Shop Drawings: a. Test reports: In accordance with specified test methods. b. Warranty: agreeing to repair or replace defective material within warranty period. c. Certificates that system meets requirements. 3. Samples: a. Submit 3 samples of each required aluminum finish. b. Color samples for Duranar finish shall be submitted from the actual production line. Lab produced samples are not acceptable. 4. Test reports (aluminum storefronts): Furnish certified test reports verifying that the system being submitted has been previously tested and meets the specified performance criteria. Test reports are not to be considered as a substitution for engineer calculations required elsewhere QUALITY ASSURANCE A. Standards: Except as otherwise indicated, the requirements for aluminum doors and frames, and the terminology used in this Section, are those of NAAMM, AAMA and AA and in particular, those of the "Entrance Manual" by NAAMM. B. Regulatory Requirements: 1. ANSI A117.1 "Making Buildings and Facilities Accessible to and Usable by Physically Handicapped People." 2. Public Law "The Americans with Disabilities Act of 1990 (ADA). 3. ADA Accessibility Guidelines (ADAAG). 4. The Arizonans with Disabilities Act of 1992 Administrative Rules (AzDAAG) C. Performance Requirements: Provide aluminum entrance and storefront assemblies that comply with specified performance characteristics. Each system shall be tested by a recognized testing laboratory or agency in accordance with specified test methods. 1. Environmental Requirements: a. Air infiltration: These systems shall be designed to perform in accordance with ASTM E283. Infiltration shall not exceed 0.06 cfm per square foot of fixed area. b. Water infiltration: The systems shall be designed to perform in accordance with ASTM 331. No water penetration at a test pressure of 10 psf A Rev. 1 December 11, 1998
2 2. Structural Requirements: a. Windload: Based on local windload requirements, inward and outward, the maximum mullion spacing shall not provide a deflection greater than L/175 of the total span and allowable stress with a safety factor of 1.65 when tested in accordance with ASTM E330. b. Deadloads: The system shall not deflect more than 1/8 inch at the center point of a horizontal member, nor more than 1/16 inch for the door header for the following glazing thicknesses: 1) 3.25 psf for 1/4 inch glass. 2) 6.5 psf fo 1-inch insulated glass. c. Thermal movement: Systems shall be designed and installed to provide for thermal expansion and contraction within the system components caused by a maximum 170 degree cycling temperature without causing detrimental effects to system or components PROJECT/SITE CONDITIONS A. Field Measurements: 1. Whenever possible, check the actual openings in the construction Work by accurate field measurement before fabrication, and show recorded measurements on final shop drawings. 2. Coordinate fabrication schedule with construction progress as directed and avoid delays of the Work. 3. Where necessary, proceed with fabrication without field measurement, and coordinate installation tolerances to ensure proper fit of units. PART 2 PRODUCTS 2.01 MANUFACTURERS A. Specifications are based on FA-SET S.S.G. frames and Series 350 doors as manufactured by Kawneer Co. B. Products equaling or exceeding quality requirements manufactured by EFCO Corporation, Monett, Missouri, or which are prior approved are acceptable for bidding MATERIALS A. Framing members, transition members, mullions, adapters, and mountings: Extruded 6063 T5 aluminum alloy (ASTM B221 - Alloy G.S. 10aT5). B. Screws, miscellaneous fastening devices, and internal components: Fasteners, where exposed, shall be aluminum, stainless steel or zinc plated steel in accordance with ASTM B633. Perimeter anchors shall be aluminum or steel, providing the steel is properly isolated from the aluminum. C. Glazing gaskets: EPDM elastomeric extrusions. D. Single acting entrance frame weathering: Non-porous, polymeric material. E. Steel Sections: ANSI/ASTM A36; shaped to suit mullion sections. F. Shop and Touch-Up Primer for Steel Components: SSPC 15, Type 1, red oxide. G. Touch-Up Primer for Galvanized Steel Surfaces: SSPS 20, zinc rich type. H. Aluminum Break Metal: Finish to match window frame, in sufficient gauge to prevent oil canning A Rev. 1 December 11, 1998
3 2.03 COMPONENTS A. Sizes and Profiles: The required sizes for doors and frame units, and profile requirements, are shown. Provide Optional Cover (Kawneer Part No ) at all exterior window wall framing (vertical and horizontal) with specified finish. B. Sill Adaptor (Interior): Provide extruded aluminum, finish to match interior of window wall, as indicated on drawings FABRICATION A. General 1. Complete the cutting, fitting, forming, drilling, and grinding of metal work prior to cleaning, finishing, treatment, and application of coatings. 2. Weld by methods recommended by the Manufacturer and AWS to avoid discoloration at welds. 3. Grind exposed welds smooth and restore mechanical finish. 4. Remove arrises from cut edges and ease edges and corners to a radius of approximately 1/64 inch (0.40mm). 5. Conceal fasteners, wherever possible, except as otherwise shown. 6. Maintain continuity of line and accurate relation of planes and angles. 7. Provide secure attachment and support at mechanical joints, with hairline fit of contacting members. 8. Reinforce the Work as necessary for performance requirements, and for support to the structure. 9. Separate dissimilar metals with bituminous paint or preformed separators which will prevent corrosion. 10. Separate metal surfaces at moving joints with non-metallic separators to prevent "freeze-up" of joints. B. Frames 1. Fabricate tubular assemblies as shown, with either welded or mechanical joints in accordance with Manufacturer's standards, with concealed fasteners wherever possible. 2. Provide members of the size, shape, and profile shown. 3. Reinforce internally with steel channel shapes as shown, or as necessary to support the required loads. 4. Weatherstripping: Provide compression weatherstripping on door-contact face of door stops on exterior door frames and/or other frames where indicated. 5. Glass framing members shall provide for flush glazing with through sight lines, without projecting stops for 1/4 inch (6mm) thick glass. 6. Provide glazing system for frames to receive lights. Design system for replacement of glass, but for non-removal of glass from exterior. 7. System shall provide resilient settings for glass by use of EPDM elastomeric extrusions. 8. Fabricate frame assemblies for exterior walls with flashing and weeps to drain penetrating moisture to exterior. 9. Provide anchorage and alignment brackets for concealed support of assembly from the building structure. 10. Allow for thermal expansion of exterior units. 11. Include flashings in conjunction with components as detailed, finished to match exterior finish. 12. Provide sill adapter and covers as specified. C. Aluminum Doors (Swinging) 1. Performance: Resistance to corner racking shall be tested by the Dual Moment Load test as follows: a. Test section shall consist of standard top door corner assembly. Side rail section shall be 24 inches (600mm) long and top rail section 12 inches (300mm) long. b. Anchor "top rail" positively to test bench so that corner protrudes 3 inches (75mm) beyond bench edge A Rev. 1 December 11, 1998
4 c. Anchor a lever arm positively to side rail at a point 19 inches (480mm) from inside edge of top rail. Attach weight support pad at a point 19 inches (480mm) from inner edge of side rail. d. Test section shall withstand a load of 245 pounds (111kg) on the lever arm before reaching the point of failure, which shall be considered a rotation on the lever arm in excess of 45 o. 2. Materials: Sections shall be extruded from 6063-T5 aluminum alloy (ASTM B221 - Alloy G.S. 10A T5). 3. Fasteners, where exposed, shall be aluminum, stainless steel or plated steel in accordance with ASTM A-164. Perimeter anchors shall be aluminum or steel, providing the steel is properly isolated from the aluminum. 4. Glazing gaskets shall be EPDM elastomeric extrusions. 5. Major portions of the door stiles shall be inch (3mm) in thickness and glazing molding shall be inch (1.27mm) thick. 6. Construction: a. Vertical Stiles: 3-1/2 inches (90mm). b. Top Rail: 3-1/2 inches (90mm). c. Bottom Rail: 12 inches (254mm). d. Corner construction: Both sigma deep penetration and fillet weld and mechanical clip fastening. e. Glazing stops: Snap-in type with EPDM glazing gaskets. 7. Door shall be weatherstripped on 3 sides with metal-backed pile cloth installed in door and/or frame. A weathered adjustable astragal with stainless steel backing shall be provided as pivoted stiles and at meeting stiles of pairs of doors. Bottom shall be weathered with an EPDM blade gasket sweep strip applied with concealed fasteners. 8. Hardware: Provide the following items: a. Pivot hinges, push-pulls: Architects classic style CO15, surface closers, threshold, weatherstrip, door bottom, and MS lock: Aluminum Door Manufacturer's standard. b. Lock and Cylinder: As specified in Section D. Hardware Installation at Factory: 1. Cut, reinforce, drill and tap frames as required to receive hardware except do not drill and tap for surface-mounted items until the time of installation at the Project Site. Comply with Hardware Manufacturer's instructions and template requirements. Use concealed fasteners wherever possible. 2. Install hardware, except surface-mounted hardware, at fabrication plant. Remove only as required for final finishing operations, and for delivery and installation of the Work at the Project Site. E. Aluminum Finishes 1. After fabrication of doors and frames prepare the aluminum surfaces for finishing in accordance with the aluminum producer's recommendations and standards of the finisher or processor. 2. Process components of each assembly simultaneously to attain complete uniformity of color. 3. Exterior Finish (Cover) for Window Wall: PPG Duranar (2 coat) paint coating with 70% Kynar 500/Hylar a. Primer: As manufactured by PPG. b. Top coat: Duranar UC54137 Beige. 4. Interior Finish for Window Wall and Door Interior / Exterior Finish: Dark Bronze anodized, Architectural Class 1 anodic coating conforming to Aluminum Association Designation AA-M-12 C22 A42. Kawneer Permanodic #40 Dark Bronze is acceptable. F. Custom Fabrications: 1. Back-up Plates: Milled 3/8 solid aluminum x 1-1/4 x 8. Drill and tap for (4) No. 8 machine screws, (2) each end for a total of (4) each plate. Provide as follows: a. Door Hinge: (1) plate each at frame jamb and door stile. b. Closer: (1) plate each at frame head and door rail (where closers are specified). c. Provide at the following doors: 101, 130B, 132A, and 132B A Rev. 1 December 11, 1998
5 PART 3 EXECUTION 3.01 EXAMINATION A. Verification of Conditions: Examine subsurfaces to receive Work and report detrimental conditions in writing to Architect. Commencement of Work will be construed as acceptance of subsurfaces. B. Coordination: Coordinate with other Work which affects, connects with, or will be concealed by this Work PREPARATION A. Field Measurements: Take field measurements prior to preparation of Shop Drawings and fabrication, where possible, to ensure proper fitting of the Work. Allow for trimming and fitting wherever the taking of field measurements before fabrication might delay the Work INSTALLATION A. Comply with Manufacturer's Specifications and recommendations for the installation of aluminum doors and frames. 1. Furnish necessary material, labor, and equipment for the complete installation of the following: glass framing, vertical and horizontal mullions, transitional members connecting these components, adapters and mountings for trim moldings and facing (cover) materials. 2. Set units plumb, level and true in line, without warp or rack of frames, doors or panels. 3. Anchor securely in place. 4. Separate aluminum and other corrodible metal surfaces from sources of corrosion or electrolytic action at points of contact with other materials. 5. Set sill members and other members in a bed of compound as shown, or with joint fillers or gaskets as shown to provide weathertight construction. B. See Section for compounds, fillers and gaskets to be installed integrally with door and frames. C. See Section for installation of glass shown to be glazed into frames and doors CLEANING A. Clean aluminum surfaces promptly after installation of frames, exercising care to avoid damage of the protective coating. B. Remove excess glazing and sealant compounds, dirt, and other substances. END OF SECTION 98055A Rev. 1 December 11, 1998
Specification Section Storefront Systems has been revised. Omit previously issued Storefront section.
December 28, 2018 ADDENDUM NO. 2 To: Re: Bidders Corey Pitts, NewQuest Properties This Addendum forms a part of the contract documents identified above. Acknowledge the receipt of this Addendum on the
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More informationSECTION FOLDING ALUMINUM FRAMED WALL SYSTEM
SECTION 08417 FOLDING ALUMINUM FRAMED WALL SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Folding aluminum framed door system. 2. Door hardware. 3. Glass. 1.2 SYSTEM DESCRIPTION A. Aluminum-framed
More informationAluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS
Aluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS This suggested guide specification has been developed using the current edition
More informationSECTION ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS
PART 1 GENERAL SECTION 08 1116 ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS 1.01 SECTION INCLUDES A. Aluminum-framed storefront, with vision glass. B. Infill panels of glass. C. Aluminum doors
More informationSECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 41 13 (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and
More informationSECTION DETAILS (MECHANICALLY ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationCOVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior and interior storefront framing. 2. Exterior and interior manual-swing entrance
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationImpact-Resistant Entrances Series
ARCHITECTURAL PRODUCTS Impact-Resistant Entrances Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND CURTAINWALL
SECTION 084116 - ALUMINUM-FRAMED ENTRANCES AND CURTAINWALL PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior and interior curtainwall framing. 2. Curtainwall framing for punched openings. 3.
More informationFL200 13/4 x41/2 GUIDE SPECIFICATION. Non-Thermal Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationMPG Series 2250T Thermally Broken Aluminum Window
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2250T Thermally Broken Aluminum Window PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows complete with hardware
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY. A. Section Includes:
SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Exterior storefront framing. 2. Storefront framing for ribbon walls. 3. Storefront framing
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS 1. PART 1 GENERAL 1.1 WORK INCLUDED: 1. Provide labor, material, equipment and services to furnish and install aluminum windows shown on drawings and specified herein. Window
More informationMPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series
SECTION 08520 ALUMINUM WINDOWS P a g e 1 MPG Series 2780-ZS Thermally Broken Aluminum Window Zero Sightline Series PART 1 GENERAL 1.01 Work Included A. Furnish and install aluminum architectural windows
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationSECTION ALUMINUM CURTAIN WALL PART 1 - GENERAL
SECTION 08921 - ALUMINUM CURTAIN WALL PART 1 - GENERAL 1.01 DESCRIPTION A. Work of this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationArchitectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION
Architectural Single-Hung Aluminum Window Series L701T SH-AW130 GUIDE SPECIFICATION Section 08520 Aluminum Windows PART 1: WORK INCLUDED A. The conditions of the contract and applicable sections of Division
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Cast
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationSWING DOOR SPECIFICATION
SWING DOOR A1 Work included: Furnish all necessary materials, labour and equipment for the complete installation of aluminum entrance doors, door frames and hardware as detailed on the drawings and specified
More informationHeavy Commercial / Architectural Projected Windows Series L900T AW150
Heavy Commercial / Architectural Projected Windows Series L900T AW150 Section 08520...Aluminum Windows PART 1: WORK INCLUDED GUIDE SPECIFICATION A. The conditions of the contract and applicable sections
More informationSECTION STAINLESS STEEL WALL PANELS
SECTION 07400 PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Dry joint, Rainscreen stainless steel wall panel system. 2. Accessories including attachments, clips, sub girts, shims, and fasteners 3.
More informationTMW 450 TECHNICAL MANUAL
ARCHITECTURAL METALS, INC. TMW 450 TMW 450 TECHNICAL MANUAL TMW 450 ARCHITECTURAL METALS, INC. BLANK PAGE FEATURES ARCHITECTURAL METALS, INC. TMW 450 FEATURES TMW 450 is 6 3/4" deep with a 2" wide sightline
More informationNorth Hanover Township School District North Hanover Township, New Jersey
SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationA. Section includes extruded aluminum windows with operating sash, operating hardware, and insect screens.
SECTION 08 51 13 - Page 1 PART 1 GENERAL 1.1 SUMMARY A. Section includes extruded aluminum windows with operating sash, operating hardware, and insect screens. B. Related Sections: 1. Section 07 92 00
More information2000/2100/2200 Series Heavy Commercial Sliding Patio Doors
2000/2100/2200 Series Heavy Commercial Sliding Patio Doors MANKO WINDOW SYSTEMS, INC. 800 HAYES DRIVE MANHATTAN, KANSAS 66502 PHONE: (800) 642-1488 (785) 776-9643 FAX: (800) 576-2656 (785) 776-9644 MANKO
More informationSECTION A1 SERIES 200, 300 AND 500 ENTRANCE DOORS
SECTION A1 SERIES 200, 300 AND 500 ENTRANCE DOORS TABLE OF CONTENTS Features... 3 Series 200 Entrance... 4 Series 300 Entrance... 5 Series 500 Entrance... 6 Miscellaneous Muntins and s... Specifications
More informationSILVER LINE BUILDING PRODUCTS. Series 1700 Heavy Commercial Aluminum Double Hung. HC65 48 x84 / HC50 60 x96 Replacement Window
DIVISION 08 / SECTION 08505 METAL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: GENERAL Series 1700 Heavy Commercial Aluminum Double Hung 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE
More informationSection A1 Table of Contents STANDARD ENTRANCES. Series 213 Narrow Stile Series 380 Medium Stile Series 500 Wide Stile
Section A1 Table of Contents STANDARD ENTRANCES Series 213 Narrow Stile Series 380 Medium Stile Series 500 Wide Stile Specifications - Series 213, 380 & 500...S1-S6 Features and Benefits... 1 Selection
More informationSECTION EXTERIOR GRILLS AND SCREENS
SECTION 10 82 13 PART 1 GENERAL PART 1 1 SUMMARY A. Section Includes: 1. Exterior perforated aluminum screen wall system with Ombrae TM Optical Tile imaging technology. 2. Accessories including attachments,
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationFL550 21/2 x5 GUIDE SPECIFICATION. Impact-Resistant Storefront
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide
More informationSERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651
SERIES SA30 STEEL/ALUMINUM FIXED DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows as
More informationFIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4. Glazing Thickness (Maximum): 1
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com FIXED SERIES 6200 AAMA/WDMA/CSA 101/I.S.2/A440-08
More informationAluminum Flush Doors and Frames SPECIFICATIONS. Section [8120] PART 1 GENERAL
Aluminum Flush Doors and Frames SPECIFICATIONS Section 081116 [8120] Cline Aluminum Doors, Inc. 112 32nd Avenue West Bradenton, FL 34205-8907 Toll-Free (800) 648-6736 Office (941) 746-4104 Fax (941) 746-5153
More informationDivision 8 Section "Flush Wood Doors" for louvers in wood doors. Division 15 Sections for louvers that are a part of mechanical equipment.
0 0 0 0 0 SECTION 000 - LOUVERS AND VENTS PART GENERAL RELATED DOCUMENTS EASTLAKE FIRE STATION REPLACEMENT HILLSBOROUGH COUNTY CIP # Drawings and general provisions of the Contract, including General and
More informationALL-ALUMINUM DOOR & WINDOW FRAMING
ALL-ALUMINUM DOOR & WINDOW FRAMING WITH INTEGRATED ALUMINUM DOOR STOP SECTION 08 41 13 ALUMINUM FRAMED ENTRANCES AND STOREFRONTS SPECIFICATION PART 1 GENERAL 1.1 SECTION INCLUDES: A. Prefinished aluminum
More information7000 Series Curtain Wall Information Specifications
7000 Series Curtain Wall Information Specifications Information All framing members shown in this section, unless noted otherwise, are stock items in dark bronze or clear anodic coatings and are available
More informationFL550T 21/2 x5. GUIDE SPECIFICATION Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront. Thermal Impact-Resistant Storefront
Series FL550T Thermal (21/2 x 5 ) Impact-Resistant Storefront Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410
More informationThe Metropolitan Sewer District of Greater Cincinnati
The Metropolitan Sewer District of Greater Cincinnati Sanitary Sewer No. 5174 & 5174A, CIP No. 2004-21 & 2005-10 Sycamore Creek WWTP Expansion & Upgrade Phase 3 and 4 Date Issued: 03/25/08 ADDENDUM NO.
More informationTMS 114 XT TECHNICAL MANUAL
TECHNICAL MANUAL BLANK PAGE FEATURES FEATURES is center set flush glazed systems that are 4 1/2" deep with a 2" wide sightline Glaze from the outside or inside Screw spline or shear block fabrication Glazing
More informationSPECIFICATIONS SECTION 08600
PART 1 GENERAL 1.1 SECTION INCLUDES A. Design, engineering, production drawings, and documents. Detailed design and attachment of metal-framed skylight will be provided as noted in the following specifications.
More informationSPECIFICATIONS FOR AluSystems Aluminum Composite Panels Series 20 Dry Joint 1.00 GENERAL 1.01 RANGE OF WORK Section includes: Laminated panels and attachment systems for use as exterior cladding. A. Provide
More informationPW251 21/2 x7 GUIDE SPECIFICATION. Curtain Wall
Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08900 ALUMINUM CURTAIN WALL This suggested guide specification has
More informationT700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD)
T700 SERIES(AW50)-Impact (Formerly 8050 series) SINGLE HUNG 3 1/4 FRAME DEPTH (SIDE LOAD) FEATURES 1.) Available Configurations -Single hung -Oriel style (optional) 2.) Main frame / Sash -Drop-in glazing
More informationHORIZONTAL SLIDER SERIES 700. Main Frame Depth: 2 3/4 Glazing Thickness (Maximum): 5/8 Thermal Break:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 700 Main
More informationSECTION HANDRAILS AND RAILINGS. A. Section Cast-In-Place Concrete; coordination with substrate.
SECTION 05520 HANDRAILS AND RAILINGS PART 1 GENERAL 1.1 SECTION INCLUDES A. Welded stainless steel railing systems. 1.2 RELATED SECTIONS A. Section 03300 - Cast-In-Place Concrete; coordination with substrate.
More informationSignature Series 5 Lap SECTION ALUMINUM WINDOWS
Signature Series 5 Lap SECTION 08 51 13 ALUMINUM WINDOWS PART 1 GENERAL 1.01 SUMMARY A. Related Documents: Conditions of the Contract, Division 1 - General Requirements, and Drawings apply to Work of this
More informationTMS 152 / 152T / 152XT TECHNICAL MANUAL
TMS 152 / 152T / 152XT TECHNICAL MANUAL BLANK PAGE FEATURES FEATURES TMS 152 (non-thermal), 152T (single thermal barrier), and 152XT (double thermal barrier) are front set flush glazed systems that are
More informationAluminum-Framed Entrances and Storefronts
University of New Hampshire University of New Hampshire Scholars' Repository Division 08 Openings Chapter 5 Technical Construction and Renovation Standards 1-25-2013 084113 - Aluminum-Framed Entrances
More informationMARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
More informationAUGUST, 2017 IR 500/501 Framing 1 EC ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS Guide Specs
AUGUST, 2017 IR 500/501 Framing 1 EC 97909-095 084113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS Guide Specs SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS This suggested guide specification
More informationSECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 41 13 (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationBID # College Center EXTERIOR DOOR REPLACEMENT SECTION "C" TECHNICAL SPECIFICATIONS OWNER
BID # 16-15 College Center EXTERIOR DOOR REPLACEMENT SECTION "C" TECHNICAL SPECIFICATIONS OWNER Board of Trustees Middlesex County College 2600 Woodbridge Avenue P.O. Box 3050 Edison, New Jersey 08818-3050
More informationSECTION U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR
Page 1 of 6 SECTION 08 39 80 U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR U.S. Aluminum has designed one of the most demanding air and water protection products, the BAL- 350 Small
More informationSECTION MISCELLANEOUS METALS
PART 1 GENERAL 1.1 WORK OF THIS SECTION A. Contractor shall provide all labor, materials, equipment and incidentals as shown, specified and required to furnish and install all miscellaneous metal fabrications
More informationSECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN
SECTION 08350 MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSeries B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
More information3. Reinforcement: Reinforce and/or modify framing system as required to accept door hardware, accessories, operators, security, etc.
08400-1 08400 ALUMINUM STOREFRONT WINDOW & DOOR FRAMING A. Scope This section covers furnishing and installing all aluminum doors, door frames, and aluminum store front systems and related hardware as
More informationSECTION PREHUNG WOOD DOORS. Display hidden notes to specifier. (Don't know how? Click Here)
SECTION 08 14 00 PREHUNG WOOD DOORS Display hidden notes to specifier. (Don't know how? Click Here) Copyright 2014-2016 ARCAT, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. French Doors.
More informationSection A2 Table of Contents ALL GLASS ENTRANCES
Architectural Aluminum Entrances Storefronts Curtain Walls Impact-Resistant Systems Section A Table of Contents ALL GLASS ENTRANCES Specifications...S-S Swing Type A... - Swing Type F... - Swing Type P...
More informationSECTION METAL WALL PANEL SYSTEM
CSI Format for Metal Wall Panel System Specification SECTION 07410 METAL WALL PANEL SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. Exterior Metal Plate Wall Panels B. Substructure and Framing C. Structural
More informationSECTION E INDEX CURTAINWALL FRAMING SYSTEMS
SECTION E INDEX CURTAINWALL FRAMING SYSTEMS E PAGE DESCRIPTION 0 CURTAINWALL FRAMING SPECIFICATION 0 SERIES /" () WIDE THERMALLY IMPROVED CURTAIN WALL FRAMING SYSTEM FOR SEALED UNIT GLAZING. 00 SERIES
More informationUnited Window & Door - Series 5500 New Construction Double Hung Windows Specifications
United Window & Door - Series 5500 New Construction Double Hung Windows Specifications Part 1 GENERAL 1.01 INCLUSIONS 1. All windows as called for in this specification will be furnished with all necessary
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationDIVISION VIII - DOORS AND WINDOWS
DIVISION VIII - DOORS AND WINDOWS SECTION 08121 INTERIOR ALUMINUM DOORS, DOOR FRAMES, AND OFFICE FRONT FRAMING (SOLUTIONS II SYSTEM) PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established
More informationRAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012
SECTION 10200 - LOUVERS AND VENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationGuide Specifications- Section
Guide Specifications- Section 084113 LaCantina ALUMINUM Folding Door System PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum and glass folding door system with fingertip operation up to 52 wide and 10
More informationDOUBLE HUNG SERIES 3500 AAMA/WDMA/CSA 101/I.S.2/A AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: C.R.F.
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com DOUBLE HUNG SERIES 3500 AAMA/WDMA/CSA
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationPROJECT OUT SERIES 6300 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT OUT SERIES 6300 AAMA/WDMA/CSA
More informationSILVER LINE BUILDING PRODUCTS
DIVISION 08 / SECTION 08560, VINYL WINDOWS SILVER LINE BUILDING PRODUCTS SPECIFICATIONS: 2200/2300/2600 Vinyl Single Hung Windows R50/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2.
More information1 3 4 Tie Rod Aluminum Swing Entrance Doors
Windows Curtain Walls Entrances Storefronts Series T200 Narrow Stile Series T300 Medium Stile T500 Wide Stile Configurations Narrow Stile (2 1 8 ) Medium Stile (3 1 2 ) Wide Stile (5 ) EFCO tie rod entrances
More informationB. Glazing: Physically and thermally isolate glazing from framing members.
SECTION 08410 - ALUMINUM ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationAluminum Component Pipe Railings
1 SECTION 05 7360 ALUMINUM COMPONENT PIPE RAILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Aluminum component pipe handrails and railings. 1.02 RELATED REQUIREMENTS A. Section 02 9000: Landscaping: Installation
More informationSeries 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction
SPECIFICATIONS: Series 4900 Vinyl Single Hung Windows R50/R45/R35/R30 Performance for New Construction GENERAL 1. SECTION INCLUDES 2. RELATED SECTIONS 3. QUALITY ASSURANCE A. General. B. Test Units. 1.
More informationSERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651
SERIES STB30 STEEL FIXED THERMAL BREAK DETENTION WINDOWS SECTION 08651 PART 1 GENERAL 1.1 DESCRIPTION A. Work Included: 1. Furnish all labor and materials to complete the fabrication of detention windows
More informationSECTION ALUMINUM-FRAMED STOREFRONTS
SECTION 08411 ALUMINUM-FRAMED STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Includes But Not Limited To 1. Furnish and install aluminum storefront entry system, including hardware, glazing, and calking, as
More informationSECTION (10705) EXTERIOR SUN CONTROL DEVICES
10 71 13 SECTION (10705) EXTERIOR SUN CONTROL DEVICES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION COMPOSITE WALL PANELS PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 07 4243 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Composite wall panel system consisting of aluminum-faced composite panels in a rainscreen application as part of the assembly described below.
More informationPRODUCT SPECIFICATION THE 9500 SERIES FAMILY - SERIES 9502 / 9503 THERMALLY BROKEN ALUMINUM OUTSWING BALCONY DOOR
PART 1 - GENERAL 08 13 16 ALUMINUM DOORS (Outswing Aluminum-Framed Glass Doors) A high-quality thermally broken aluminum balcony outswing door designed for residential high rise construction. 1.1 SUMMARY
More informationSECTION METAL FRAMED SKYLIGHTS
SECTION 08630 - METAL FRAMED SKYLIGHTS PART 1: GENERAL 1.01 SUMMARY A. Section includes: Design, structural engineering, manufacture, fabrication, finishing of metal-framed skylights: 1. Glass and glazing
More informationCASEMENT PROJECT OUT SERIES 6400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 3 1/4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 6400
More informationCASEMENT PROJECT OUT SERIES 2400 AAMA/WDMA/CSA 101/I.S.2/A Structural Performance: Thermal Break: Main Frame Depth: 2 3/8
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com CASEMENT PROJECT OUT SERIES 2400
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 GENERAL 1.1 SECTION INCLUDES A. Projected windows. B. Fixed windows. 1.2 RELATED SECTIONS A. Section 07900: Joint Sealers. B. Section 08400: Entrances and Storefronts.
More informationK. ASTM F436- Standard Specification for Hardened Steel Washers; 2011.
DIVISION 05 METALS 05 12 00 STRUCTURAL STEEL FRAMING PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural steel framing members, support members. 1.2 RELATED REQUIREMENTS A. Section 05 50 00 - Metal Fabrications:
More informationSECTION VINYL (PVC) WINDOWS
SECTION 085313 VINYL (PVC) WINDOWS SERIES 3000/3900 NEW CONSTRUCTION DOUBLE HUNG PART 1 GENERAL 1.01 SECTION INCLUDES A. All windows of the types and sizes called for in this specification shall be furnished
More informationSECTION SERIES ALL GLASS ENTRANCES
1 SECTION 08 4210 1200 SERIES ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1.
More informationPROJECT IN SERIES 1300 NARROW SIGHT LINE AAMA/WDMA/CSA 101/I.S.2/A Structural Performance:
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com PROJECT IN SERIES 1300 NARROW SIGHT
More informationHORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 910 ANSI/AAMA/NWWDA
More informationHORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA 101/I.S Structural Performance: Thermal Break: C.R.F.: 50. Thermal U Value:.66. Main Frame Depth: 4
GUIDE SPECIFICATION Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com HORIZONTAL SLIDER SERIES 900 ANSI/AAMA/NWWDA
More information