REVISIONS TO ICC-ES ACCEPTANCE CRITERIA AC308 (JUNE 2013)
|
|
- Annabel Parrish
- 5 years ago
- Views:
Transcription
1 Post-installed Adhesive Anchors REVISIONS TO ICC-ES ACCEPTANCE CRITERIA AC308 (JUNE 2013)
2 INCORPORATION OF ADHESIVE ANCHORS INTO ACI 318 Background In response to the 2006 ceiling collapse at the Boston Big Dig tunnel, ACI began to formulate an approach to include adhesive anchors in the ACI 318 code. With the issuance of the ACI test criteria and the adoption by the 2012 International Building Code (IBC), ICC-ES made significant revisions to AC308 to incorporate provisions contained in ACI and to reference the design provisions of ACI 318. Significant Change in Acceptance Criteria* Research of sustained load response of adhesive anchors determined that the qualification of adhesive anchors on the basis of concrete temperatures corresponding to room temperatures (75 F) did not address temperatures sometimes seen in typical applications. The 2013 version of AC308 changed the testing criteria to a min. long term temp. of 110 F to match ACI AC308 June 2006, Table 9.1 Temperature category Long-term temperature, Tlt, F Short-term temperature, Tst, F A B 0.60 x (short-term 110 test temp) AC308 June 2013/ACI , Table 8.1 Temperature category Long-term temperature, Tlt, F Short-term temperature, Tst, F A B 110 Tlt + 20 Effects of the Code Change on Adhesive Anchors* Bond Strength ( ) HY HIT-Z HY HAS RE 500-SD Other Fast Cure (average) Other Epoxy (average) ACI 308 June 2006 (73 F) NOTE: Solid colors are actual or expected relative capacities based on ACI (110 F) 0 3/8 x 3-3/8 1/2 x 4-1/2 5/8 x 5-5/8 3/4 x 6-3/4 * Contact Hilti for a complete list of changes
3 BEST-IN-CLASS SOLUTIONS Anchoring Applications HIT-HY 200 SafeSet Performance Hilti s new HIT-Z rod, in combination with HIT-HY 200, outperforms standard threaded rod adhesive anchoring systems in every available diameter. HIT-HY 200 in combination with the HIT-Z rod is the best anchoring system in its class. HIT-HY 200 in combination with the hollow drill bit and Hilti VC 20/40 vacuum cleaner provides full anchor performance without additional hole cleaning steps. Productivity and Reliability The HIT-Z rod system completely removes the need for any hole cleaning.* The SafeSet system (HIT-HY 200, and either the HIT-Z rod, or the hollow drill bit, and Hilti VC 20/40 vacuum cleaner) system makes subsequent hole cleaning completely unnecessary. Both systems allow fewer installation steps and extremely high reliability in anchoring applications. Set Hilti SafeSet Technology Up to 60% faster! Done Set Productivity gain Hilti SafeSet Technology Up to 60% faster! Done Productivity gain Rebar Applications HIT-RE 500-SD SafeSet ** Best-in-Class Installation Solutions SafeSet for HIT-HY 200-R and HIT-RE 500-SD**(hollow drill bits, Hilti VC 20/40 vacuum cleaner) require no manual hole cleaning. The HDE 500 Battery dispenser has the fastest adhesive dispensing to help complete rebar installation within the work time of the adhesive anchor. Superior installation accessories (for hole cleaning and adhesive injection), on-site installer training, and Profis rebar *** (rebar design calculations) software are available. Approvals HIT-RE 500-SD and HIT-HY 200-R have been tested according to AC 308 rebar qualifications with ICC-ES report pending. * When used with Hilti HY 200, holes have to be cleaned when used below 41 F and in diamond cored holes ** ICC-ES report for HIT-RE 500-SD with hollow drill bit pending *** Profis rebar available in July 2015
4 NO MANUAL CLEANING REQUIRED. Set anchors and rebar reliably. With hole cleaning Without hole cleaning using the Hilti HIT-Z Rod Load [lb] No hole cleaning Load [lb] With standard hole cleaning or self-cleaning Hilti hollow drill bit Displacement [in] Displacement [in] Potential effects of inadequate hole cleaning When a threaded rod or rebar is set with conventional injection adhesive, the load it s capable of taking may be very low if the hole is inadequately cleaned after drilling. The Hilti SafeSet system eliminates a cleaning step while still providing excellent load values. Hilti Injectable mortar HIT-HY200 with SafeSet Technology The new SafeSet System featuring HIT-HY 200 allows a fastening point to take high loads, as though the hole were cleaned using traditional installation methods.
5 BEST-IN-CLASS ADHESIVE ANCHORING SOLUTIONS. Anchoring Rebar HIT-HY 200-A / HIT-HY 200-R HIT-RE 500-SD / HIT-HY 200-R Fast cure anchoring system Longer working time Ability to apply loads shortly after installation Ability to perform deep embedment installations Best-in-class anchor performance when used with HIT-Z rod Highly reliable anchor installation with SafeSet technology No additional hole cleaning necessary with the SafeSet system Fast and easy installation when used with hollow drill bit and VC 20/40 vacuum cleaner, or HIT-Z rod HIT-RE 500-SD for rebar installations up to #10 rebars in hammer drilled and diamond cored holes HIT-HY 200-R for rebar installation up to #8 rebars in hammer drilled holes* Reliable, fast and easy installation when installed with Hilti hollow drill bit with VC vacuum cleaner (up to #7 rebars) Order Information Description Package Contents Item No. HIT-HY 200-A 11.1 fl oz Includes 25x foil pack HIT-HY 200-A 11.1 fl oz Includes 25x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-HY 200-A 16.9 fl oz Includes 20x foil pack HIT-HY 200-A 16.9 fl oz Includes 40x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-HY 200-A 16.9 fl oz Includes 100x foil pack, 1 battery dispenser (HDE 500-A18), 1 cartridge holder, 2 x HIT-HY 200-R 11.1 fl oz Includes 25x foil pack HIT-HY 200-R 11.1 fl oz Includes 25x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-HY 200-R 16.9 fl oz Includes 20x foil pack HIT-HY 200-R 16.9 fl oz Includes 40x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-HY 200-R 16.9 fl oz Includes 100x foil pack, 1 battery dispenser (HDE 500-A18), 1 cartridge holder, 2 x HIT-RE 500-SD 11.1 fl oz Includes 25x foil pack HIT-RE 500-SD 11.1 fl oz Includes 25x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-RE 500-SD 16.9 fl oz Includes 20x foil pack HIT-RE 500-SD 16.9 fl oz Includes 40x foil pack, 1 manual dispenser (HDM 500), 1 cartridge holder HIT-RE 500-SD 16.9 fl oz Includes 100x foil pack, 1 battery dispenser (HDE 500-A18), 1 cartridge holder, 2 x /15 SM *For rebar designs as anchor elements (ACI 318Appendix D) HY 200 can be used up to #10 rebars.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 16. Please refer the publication in its entirety for complete details on this product
More informationHIT HY 200 Implementation Into PROFIS Anchor
HIT HY 200 Implementation Into PROFIS Anchor This document provides a brief overview of some key HIT-HY 200 features, and how these features are implemented into PROFIS Anchor. The HIT-HY 200 chemical
More informationAdvancements in Adhesive Anchor Technology
One giant leap for your next project. 1 What are the typical applications you design using post-installed anchors? 2 Post-installed anchors cover a complete range of fastening applications Structural anchor
More informationThe following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17.
The following excerpt are pages from the North American Product Technical Guide, Volume 2: Anchor Fastening, Edition 17. Please refer to the publication in its entirety for complete details on this product
More informationAnchor Fastening Technology Manual. HIT-HY 170 mortar with rebar. Hilti HIT-HY 170 mortar with rebar (as post-installed conn.
Anchor Fastening Technology Manual Hilti HIT-HY 170 mortar with HIT-HY 170 mortar with rebar Version 2015-12 1 February 12, 2016 Hilti HIT-HY 170 mortar with rebar (as post-installed connection) Injection
More informationTechnical data No. 17/0001 of 25/04/2017
Hilti Corporation Feldkircherstrasse 100 FL-9494 Schaan Principality of Liechtenstein www.hilti.group Technical data No. 17/0001 of 25/04/2017 General Part Trade name Injection system Hilti HIT-RE 500
More informationSIMPLE CERTAINTY MAXIMUM VERSATILITY INCREASES ANCHOR RELIABILITY AND JOBSITE PRODUCTIVITY
SIMPLE CERTAINTY MAXIMUM VERSATILITY INCREASES ANCHOR RELIABILITY AND JOBSITE PRODUCTIVITY QUICK-CURE ADHESIVE ANCHOR FOR CONCRETE AND MASONRY APPLICATIONS THE RELIABLE CHOICE NO LONGER REQUIRES A CHOICE
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationHigh Strength Epoxy tested in accordance to ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are
More informationADHESIVE ANCHORS SIMPLE CERTAINTY WITH RED HEAD ADHESIVE ANCHOR SYSTEMS VERSATILE ADHESIVE ANCHORS FOR CONCRETE AND MASONRY APPLICATIONS
ADHESIVE ANCHORS SIMPLE CERTAINTY WITH RED HEAD ADHESIVE ANCHOR SYSTEMS VERSATILE ADHESIVE ANCHORS FOR CONCRETE AND MASONRY APPLICATIONS SIMPLE CERTAINTY IN THE SELECTION AND INSTALLATION OF ADHESIVE ANCHORS
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationHigh Strength Epoxy Tested in Accordance with ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy Tested in Accordance with ICC-ES AC308 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are completely mixed as they are dispensed from
More informationHigh Strength Epoxy Tested in Accordance with ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS DESCRIPTION/SUGGESTED SPECIFICATIONS* The 100% epoxy resin and hardener are completely mixed as they are dispensed from the dual cartridge through a static mixing nozzle,
More informationHilti HIT-CT 1 post installed rebars
Hilti HIT-CT 1 post installed rebars Injection mortar system Benefits Hilti HIT-CT 1 330 ml foil pack (also available as 500 ml foil pack) Statik mixer Rebar - Hilti Clean technology (Clean-Tec) - Environmentaly
More informationC6+ High Strength Epoxy for All. conditions. One product for most environmental conditions and weather conditions. Curing Times
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy for All Conditions DESCRIPTION/SUGGESTED SPECIFICATIONS* One product for most environmental conditions and weather conditions Design and use with confidence
More informationThe ONLY Fast Cure ICC-ES Listed Adhesive for Water-filled Holes and Submerged Concrete
ADHESIVE ANCHORING SPECIALISTS DESCRIPTION Fast Curing The ONLY Fast Cure ICC-ES Listed Adhesive for Water-filled Holes and Submerged Concrete The resin and hardening agent are completely mixed as they
More informationADVANCED ANCHOR SOLUTIONS BUILT TO CODE.
Hilti Anchoring Solutions + NCC Compliance ADVANCED ANCHOR SOLUTIONS BUILT TO CODE. Hilti. Outperform. Outlast. Hilti HIT- Hilti HIT- ANCHOR PORTFOLIO UPDATE INSIDE Hilti Anchoring Solutions + NCC Compliance
More informationAC50 Silver Adhesive Anchoring System
General Information General Information AC50 Silver Adhesive Anchoring System Product Description The AC50 Sliver is a two-component, adhesive anchoring system. The system includes injection adhesive in
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2008 Hilti North American Product Technical Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationAdhesive Anchoring Selection Guide Solid Concrete Applications
ADHESIVE ANCHORING SPECIALISTS Adhesive Anchoring Selection Guide Solid Concrete Applications Doweling into Concrete with Rebar ultimate tensile product systems key features properties performance 1,2
More informationICC-ES Evaluation Report. ESR-3342 Reissued July 1, 2013 This report is subject to renewal August 1, 2015.
ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-3342 Reissued July 1, 2013 This report is subject to renewal August 1, 2015. A Subsidiary of the International Code Council DIVISION:
More informationProduct Submittal/Substitution Request
Product Submittal/Substitution Request TO: PROJECT: PROJECT LOCATION: SPECIFIED ITEM: Section Page Paragraph Description PRODUCT SUBMIT TAL / SUBSTITUTION REQUESTED: The attached submittal package includes
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3342 Reissued 08/2017 This report is subject to renewal 08/2018. DIVISION: 04 00
More informationHilti HIT-HY 200-R 500 ml foil pack (also available as 330 ml foil pack) Static mixer
with HIT-V Hilti HIT-HY 200 with HIT-V Injection Mortar System Benefits Hilti HIT-HY 200-R 500 ml foil pack (also available as 330 ml foil pack) Static mixer HIT-V rods HIT-V (Zinc) HIT-V-F (Gal) HIT-V-R
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 587 (52) 99 0543 www.icc es.org ESR 393 Reissued 12/2017 This report is subject to renewal 12/2018. DIVISION: 04 00 00 MASONRY
More informationAustralian Engineered Fasteners & Anchor Council
Australian Engineered Fasteners & Anchor Council Setting standards for the specification, selection & application of anchors & fasteners in Australia 16/08/2012 CIA Seminar 2012 1 Disclaimer These seminar
More informationHilti HIT-RE 10 mortar Economical epoxy mortar for concrete
Hilti HIT-RE 10 mortar Economical epoxy mortar for concrete Injection mortar system Hilti HIT-RE 10 580 ml hard cartridge Benefits - Suitable for non-cracked concrete C20/25 to C50/60 - Suitable for dry
More informationAC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS
Vinylester Injection Adhesive Anchoring System PACKAGING Coaxial Cartridge 5 fl. oz. (150 ml or 9.2 in 3 ) 10 fl. oz. (280 ml or 17.1 in 3 ) Dual (Side-by-Side) Cartridge 8 fl. oz. (235 ml or 14.3 in 3
More informationProduct Submittal/Substitution Request
Product Submittal/Substitution Request TO: PROJECT: PROJECT LOCATION: SPECIFIED ITEM: Section Page Paragraph Description PRODUCT SUBMIT TAL / SUBSTITUTION REQUESTED: The attached submittal package includes
More informationProduct Submittal/Substitution Request
Product Submittal/Substitution Request TO: PROJECT: PROJECT LOCATION: SPECIFIED ITEM: Section Page Paragraph Description PRODUCT SUBMIT TAL / SUBSTITUTION REQUESTED: DEWALT Engineered By Powers DEWALT
More informationHilti HIT-HY 200 A (R) mortar with HIT-V rods
Hilti HIT-HY 200 A (R) mortar with HIT-V rods Injection mortar system Hilti HIT- HY 200-A 500 ml foil pack (also available as 330 ml foil pack) Hilti HIT- HY 200-R 500 ml foil pack (also available as 330
More informationHigh Strength Epoxy tested in accordance to ICC-ES AC308
ADHESIVE ANCHORING SPECIALISTS High Strength Epoxy tested in accordance to ICC-ES AC308 2006 IBC Compliant ICC-ES Report No. 1137 DESCRIPTION/SUGGESTED SPECIFICATIONS* The epoxy resin and hardener are
More informationHIT-RE 500 V3 INJECTION MORTAR. Technical Datasheet Update: Dec-17
HIT-RE 500 V3 INJECTION MORTAR Technical Datasheet Update: Dec-17 HIT-RE 500 V3 injection mortar Anchor design (ETAG 001) / Rods&Sleeves / Concrete Injection mortar system Foil pack: HIT-RE 500 V3 (available
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: DEWALT 701 EAST JOPPA TOWSON, MARYLAND EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 4105 Issued 08/2017 This report is subject to renewal 08/2018. DIVISION: 04 00 00
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC SOUTH 122 ND EAST AVENUE TULSA, OKLAHOMA 74146
0 ICC ES Report ICC ES (800) 42 87 (2) 99 04 www.icc es.org 000 Most Widely Accepted and Trusted ESR 282 Valid: 08/4 to 08/ DIVISION: 04 00 00 MASONRY SECTION: 04 0 9. MASONRY ANCHORS REPORT HOLDER: HILTI,
More informationDIVISION: MASONRY SECTION: MASONRY ANCHORS REPORT HOLDER: HILTI, INC DALLAS PARKWAY, SUITE 1000 PLANO, TEXAS 75024
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-4143 Issued 01/2018 This report is subject to renewal 01/2019. DIVISION: 04 00 00
More informationDESCRIPTION ADVANTAGES
ADHESIVE ANCHORING SPECIALISTS A7P-10 The Most Versatile Quick Cure Adhesive A7P-28 APPLICATIONS / USES n Concrete dowelling (slabs, walls, columns) n Steel framing (columns, beams, ledgers) n Brick pinning
More informationA7+ The Most Versatile Quick Cure Adhesive
ADHESIVE ANCHORING SPECIALISTS A7P-10 The Most Versatile Quick Cure Adhesive A7P-28 APPLICATIONS / USES n Concrete dowelling (slabs, walls, columns) n Steel framing (columns, beams, ledgers) n Brick pinning
More informationCONCRETE ANCHORING SYSTEMS
CONCRETE ANCHORING SYSTEMS Notes RH 2 CONCRETE ANCHORING SYSTEMS TABLE OF CONTENTS Anchoring Working Principles... RH 4 Red Head Adhesive Anchoring Systems... RH 7 Adhesive Anchoring Selection Guide...
More informationPost-installed reinforcement bars in structural connections
Post-installed reinforcement bars in structural connections Jorge Gramaxo Business Unit Anchors Hilti Corporation Chile 21 November, 2014 1 Agenda Applications and different methods Internal stresses in
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2011 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationSECTION ANCHOR SYSTEMS
SECTION 05 05 00 ANCHOR SYSTEMS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Anchor bolts. B. Requirement: 1. Furnish all materials, labor and equipment required to provide anchor systems not specifically
More informationESR ICC Evaluation Service, Inc. Reissued January 1, 2008 This report is subject to re-examination in one year.
ESR-1967 Reissued January 1, 2008 This report is subject to re-examination in one year. ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California
More informationSET-3G High-Strength Epoxy Adhesive. Adhesive Anchors. Cracked. Concrete CODE LISTED. Features. SET-3G Adhesive. Applications
SET-3G High-Strength Epoxy Adhesive SET-3G is the latest innovation in epoxy anchoring adhesives from Simpson Strong-Tie. Formulated to provide superior performance in cracked and uncracked concrete at
More informationPE1000+ Epoxy Injection Adhesive Anchoring System
General InformatIon GENERAL INFORMATION PE1000+ Epoxy Injection Adhesive Anchoring System PRODUCT DESCRIPTION The PE1000+ is a two-component, high strength adhesive anchoring system. The system includes
More informationTrusted ICC ES HILTI, INC. SYSTEM E ANCHOR. Conformity! Look. Evaluation. ICC-ES Evaluation
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.orgg ESR 2682 Reissued 08/2016 This report is subject to renewal 08/2018. DIVISION: 04 00
More informationEasy to Use A7 Saves You Time and Money
ADHESIVE ANCHORING SPECIALISTS Easy to Use Saves You Time and Money DESCRIPTION/SUGGESTED SPECIFICATIONS* Fast Dispensing, Fast Curing The acrylic resin and hardening agent are completely mixed as they
More informationHVZ (HVU-TZ+HAS-TZ) adhesive anchor system Anchor design (ETAG 001) / Rods&Sleeves / Concrete
HVZ (HVU-TZ+) adhesive anchor system Anchor design (ETAG 001) / Rods&Sleeves / Concrete Anchor version HVZ Mortar capsule Anchor rod: HAS-R-TZ HAS-HCR-TZ (M10-M20) Benefits - Suitable for cracked and noncracked
More informationAC100+ GOLD Vinylester Injection Adhesive Anchoring System
GENERAL INFORMATION GENERAL INFORMATION AC100+ GOLD Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC100+ Gold is a two-component vinylester adhesive anchoring system. The system
More informationHilti HIT-RE 100 mortar with rebar (as anchor)
Injection mortar system Hilti HIT-RE 100 330 ml, 500 ml and 1400 ml foil pack Statik mixer rebar BSt 500 S Benefits - suitable for non-cracked and cracked concrete C 20/25 to C 50/60 - high loading capacity
More informationCIA-GEL 7000 EPOXY. One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY
CIA-GEL 000 EPOXY One Product For All Applications ADHESIVE ANCHORING SYSTEMS FOR CONCRETE AND MASONRY City of Los Angeles Research Report No. (in Concrete, Block and Brick) City of Los Angeles Research
More informationPRO-POXY 400 A.11. New technology for all weather anchoring... PRO-POXY 400! BENEFITS:
PRO-POXY 400 ALL WEATHER EPOXY ACRYLATE HYBRID ANCHORING GEL BENEFITS: Guns & Performs to -15 F STYRENE FREE! Meets performance requirements of ASTM-C-881; Types I, II*, IV & V * ; Classes A, B & C; Grade
More informationHFX Adhesive Anchor Adhesive Anchoring Systems
HFX Adhesive Adhesive ing Systems MD300 Dispenser HFX-M Mixer HFX Cartridge Standard Silicon Dispenser Product Description Hilti HFX is a new hybrid adhesive mortar combining resin, hardener, cement and
More informationFast Cure Anchoring Adhesive
ESR-4249 Product Description ULTRABOND ACRYL-8CC is a two-component (10:1 mix ratio by volume), high strength, styrene-free, vinylester adhesive anchoring system tested for use with threaded rod and reinforcing
More informationAC200+ Acrylic Injection Adhesive Anchoring System
GENERAL INFORMATION GENERAL INFORMATION AC200+ Acrylic Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC200+ is a two-component, high strength adhesive anchoring system. The system includes
More informationHilti-HY 110 available in 330ml and 500ml foil packs. Static mixer HIT M1. Rebar BSt 500 S
Hilti HIT-HY 110 Injection Mortar System Benefits Hilti-HY 110 available in 330ml and 500ml foil packs. Static mixer HIT M1 suitable for non-cracked concrete C 20/25 to C 50/60 suitable for dry and water
More informationET Epoxy-Tie Anchoring Adhesive
ET Epoxy-Tie is a two-component, high solids, epoxy-based system for use as a high-strength, non-shrink anchor grouting material. Resin and hardener are dispensed and mixed simultaneously through the mixing
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2011 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationHilti, Inc South 122 nd East Avenue Tulsa, OK
Attached are page(s) from the 2011 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
More informationExtended Working Time Epoxy
Product Description ULTRABOND 2 is a two-component, 1:1 mix ratio, structural epoxy system that offers exceptional strength in anchoring and doweling applications and can be used in temperatures from 40
More informationHilti HIT-HY 170 mortar with HIT-V rod. Anchor Fastening Technology Manual. Hilti HIT-HY 170 with HIT-V HIS-(R)N 03 / /
Anchor Fastening Technology Manual Hilti HIT-HY 170 with HIT-V HIS-(R)N 1 Hilti HIT-HY 170 with HIT-V Injection mortar system Benefits Hilti HIT-HY 170 500 ml foil pack (also available as 330 ml foil pack)
More informationHigh performance, 2 component adhesive anchor system use in cracked & uncracked concrete. Storage Conditions. Working & Loading Times
Product Data Sheet Edition 5.7.2015 Sika AnchorFix-3001 Sika AnchorFix-3001 High performance, 2 component adhesive anchor system use in cracked & uncracked concrete Description Where to Use Advantages
More informationSubmittal Information
Adhesive INSTALLATION STEPS 35 Minute Cure Time at 60 F Fast Dispensing at all Temperatures Cures Down to 0 F and Below Multi-Patented Formula Miami-Dade County Product Control Approved Contents: 825 ml
More informationSubmittal Information
Adhesive Fast Dispensing, Fast Curing The acrylic resin and hardening agent are completely mixed as they are simultaneously dispensed from the dual cartridge through a static mixing nozzle, directly into
More informationThe installation of adhesive anchors in horizontal to
Overhead Installation of Injection-Type Adhesive Anchors An evaluation of two available methods and recommendations for ACI s installer certification program by John Silva The installation of adhesive
More informationHILTI HY 150 REBAR DESIGN GUIDE
HILTI HY 150 REBAR DESIGN GUIDE HILTI HY 150 REBAR DESIGN GUIDE 1 HY150 Rebar Dowelling using Limit States Concrete Design ( A23.3-94) The design method presented here was originally based on Eurocode
More informationLOW VISCOSITY STRUCTURAL EPOXY. Table of Contents. Made in the U.S.A. AF35LVE TECHNICAL DATA SHEET
1 Table of Contents PRODUCT DESCRIPTION PRODUCT NUMBER GENERAL USES AND APPLICATIONS ADVANTAGES AND FEATURES STANDARDS AND APPROVALS AVAILABILITY COLOR AND RATIO INSTALLATION AND COVERAGE STORAGE/SHELF
More informationICC-ES Evaluation Report Reissued March 2014 This report is subject to renewal May 1, 2015
[Type text] ICC-ES Evaluation Report www.icc-es.org (800) 423-6587 (562) 699-0543 ESR-1958 Reissued March 2014 This report is subject to renewal May 1, 2015 A Subsidiary of the International Code Council
More informationEnglish translation prepared by CSTB - Original version in French language
Member of Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 European Technical Assessment
More informationPro-Poxy 300 A.9. Where other s can t... Pro-Poxy 300 FAST. Pro-Poxy 300 FAST can! BeneFiTS:
Pro-Poxy 300 Pro-Poxy 300 FAST NON-SAG, INJECTABLE ANCHORING GEL BeneFiTS: Permitted for use in wet or damp holes Permitted in severe weathering locations Freeze-thaw resistant Suitable for seismic conditions
More informationTechnical data No. 17/0002 of 22/05/2017
Hilti Corporation Feldkircherstrasse 100 FL-9494 Schaan Principality of Liechtenstein www.hilti.group Technical data No. 17/0002 of 22/05/2017 General Part Trade name Injection system Hilti HIT-RE 500
More informationPOLYESTER INJECTION MORTAR Good Quality and Competitve Price
Good Quality and Competitve Price Date of Issue: Feb 22, 2012 PRODUCT Good Use is a chemical anchor system based on the polyester mortar. The two parts are dispensed and mixed in one action through a static
More informationSubmittal Information
Steel beam & columns Mounting machinery to concrete slab Contents CAS Number Epoxy resin Trade Secret Curing Agent Trade Secret Washed sand 14808-60-7 Recognized Worldwide Te ste d b y W arrin gto n Full
More informationHIT-ICE INJECTION MORTAR. Technical Datasheet Update: Jun-18
HIT-ICE INJECTION MORTAR Technical Datasheet Update: Jun-18 HIT-ICE injection mortar Anchor design (ETAG 001) / Rods&Sleeves / Concrete Injection mortar system Hilti HIT-ICE 296 ml cartridge Anchor rod:
More informationAC100+Gold. Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION FEATURES AND BENEFITS
Vinylester Injection Adhesive Anchoring System PRODUCT DESCRIPTION The AC100+Gold is a twocomponent vinylester adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing
More informationConstruction. Sika AnchorFix-2 High performance, two component adhesive anchoring system. Product Data Sheet Edition
Product Data Sheet Edition 7.12.2016 Sika AnchorFix-2 Sika AnchorFix-2 High performance, two component adhesive anchoring system Description Where to Use Advantages Packaging Approvals Sika AnchorFix-2
More informationFast Cure Acrylic Adhesive
Product Description ULTRABOND ASF-1000 is a two-component styrene free, acrylic system used for anchoring and doweling applications in uncracked concrete using threaded rod and rebar. It may be used in
More informationPE1000+ High Strength Epoxy Anchoring System PRODUCT DESCRIPTION GENERAL APPLICATIONS AND USES FEATURES AND BENEFITS APPROVALS AND LISTINGS PACKAGING
PE1000+ High Strength Epoxy Anchoring System PRODUCT DESCRIPTION The PE1000+ is a twocomponent, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing
More informationHilti HIT-ICE with rebar
Hilti HIT-ICE Injection mortar system Benefits Hilti HIT-ICE 296 ml cartridge Statik mixer rebar BSt 500 S - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity - suitable for
More informationESR-3574* Issued December 1, 2013 This report is subject to renewal August 1, 2014.
ICC-ES Evaluation Report www.icc-es.org (800) 4-6587 (56) 699-054 ESR-574* Issued December, 0 This report is subject to renewal August, 04. A Subsidiary of the International Code Council DIVISION: 0 00
More informationHilti HIT-RE 500 post-installed rebars
Injection mortar system Benefits Hilti HIT-RE 500 330 ml foil pack (also available as 500 ml and 1400 ml foil pack) Static mixer - suitable for non-cracked concrete C 20/25 to C 50/60 - high loading capacity
More informationRS 600 High Strength Epoxy Anchoring System
RS 600 High Strength Epoxy Anchoring System Pilgrim Permocoat, Inc. 402 S. 22nd Street, Tampa, FL 33605 (83) 248-3328 FAX# (83) 248-076 www.pilgrimpermocoat.com PILGRIM RS 600 Cartridge is a two-component,
More informationBonded (Adhesive) Anchors
Bonded (Adhesive) Anchors Click to edit Master title style www.wje.com NCSEA Seminar January 13, 2015 Overall Webinar Outline Three part presentation Part 1 Cast in place and mechanical expansion anchors
More informationThe following excerpt are pages from the Hilti North America Post- Installed Reinforcing Bar Guide.
The following excerpt are pages from the Hilti North America Post- Installed Reinforcing Bar Guide. Please refer to the publication in its entirety for complete details on this topic including data development,
More information1 Input data. Profis Anchor Company: Specifier: Address: Phone I Fax: Obeikan Tensile Struct
1 Specifier's comments: Typiacl Base plate Design (B3) for Nodes 5985 & 5977- Critical Combination LC17 (1.2D.L.+1.6S+0.8WX CASE B) 1 Input data Anchor type and diameter: HIT-HY 200 + HIT-V (8.8) M27 Seismic/Filling
More informationHigh-Strength Anchoring Epoxy
Product Description ULTRABOND is a 2-component, : mix ratio, structural epoxy system that offers exceptional strength in anchoring and doweling applications and can be used in temperatures from 40 F to
More informationMultiple DOT Listings. Product Description. General Uses & Applications. Advantages & Features
Product Description ULTRABOND 2 is a 2-component, 1:1 mix ratio, structural epoxy system that offers exceptional strength in anchoring and doweling applications and can be used in temperatures from 40
More informationAdhesive Anchors SECTION CONTENTS. General Information. Installation Information Design Information Material Information Ordering Information
General Information General Information AC100-PRO Vinylester Injection Adhesive Anchoring System ProDUCT DESCRIPTION The AC100-PRO is a two-component vinylester adhesive anchoring system. The system includes
More informationFast Gel Epoxy. Product Description. General Uses & Applications. Advantages & Features
Product Description ULTRABOND 300-FG is a two-component, fast-setting adhesive system that offers exceptional strength in anchoring and doweling applications. Its fast-setting properties are perfect for
More informationAll-Season Hybrid Anchoring Adhesive
ESR-3770 Product Description ULTRABOND 365CC is a two-component, cracked concrete, code compliant, high-performance adhesive anchoring system tested to ACI 355.4 and ICC-ES AC308. The silanecementitious
More informationDIVISION: CONCRETE SECTION: CONCRETE ANCHORS DIVISION: METALS SECTION: POST INSTALLED CONCRETE ANCHORS
0 Most Widely Accepted and Trusted ICC ES Listing Report ICC ES 000 (800) 4 6587 (56) 699 054 www.icc es.org ELC 187 Issued May 018 This listing is subject to renewal May 019. DIVISION: 0 00 00 CONCRETE
More informationAnchor Fastening Technology Manual. HIT-HY 170 mortar with rebar (as anchor) Hilti HIT-HY 170 mortar with rebar (as anchor) Version
Anchor Fastening Technology Manual Hilti HIT-HY 170 mortar with HIT-HY 170 mortar with rebar (as anchor) Version 2016-10 1 November 3, 2016 Hilti HIT-HY 170 mortar with Injection mortar system Benefits
More informationMaterials Polyester Resin Anchors: Carbon Steel grade 5.8 Stainless Steel: AISI 316
Chemset Injection is a two component polyester resin anchor system in a coaxial cartridge with mixing nozzle. Developed for fixing awkward materials in hollow and solid sections where access may be difficult.
More informationPE1000+ High Strength Epoxy Anchoring System
42 PE000+ High Strength Epoxy Anchoring System PRODUCT DESCRIPTION The PE000+ is a twocomponent, high strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing
More informationHilti HIT-RE 500 V3 mortar with HIT-V rod
Hilti HIT-RE 500 V3 Injection mortar system Hilti HIT-RE 500 V3 330 ml, 500 ml and 1400 ml foil pack Static mixer HIT-V rod Benefits - SafeSet technology: Simplified method of borehole preparation leaving
More informationCONCRETE ANCHORING SYSTEMS
CONCRETE ANCHORING SYSTEMS Notes RH 2 CONCRETE ANCHORING SYSTEMS TABLE OF CONTENTS Anchoring Working Principles... RH 4 Red Head Adhesive Anchoring Systems... RH 7 Adhesive Anchoring Selection Guide...
More informationInspection Requirements For Anchors in Concrete in Accordance With ACI and
Delaware Valley Association of Structural Engineers Seminar Inspection Requirements For Anchors in Concrete in Accordance With ACI 318 11 and the 2012 IBC January 14, 2015 J. Silva, PE, SE, F. ACI, F.
More informationAnchor Fastening Technology Manual 09 / 2012
Anchor Fastening Technology Manual 09 / 2012 0 Forword Foreword Dear customer, As it is our ambition to be the worldwide leader in fastening technology, we are continously striving to provide you with
More informationThe following excerpt are pages from the North American Anchor Fastening Technical Guide, 2011.
The following excerpt are pages from the North American Fastening Technical Guide, 2011. Contact Hilti s team of technical support specialists between the hours of 7:00am 6:00pm CST for complete details
More informationHigh-Strength Anchoring Epoxy
Product Description ULTRABOND HS-1CC is a code compliant, two-component (1:1 mix ratio by volume), high performance epoxy anchoring system approved for use in cartridges and in bulk with threaded rod and
More information