E P CONCRETE BLOCK SEALER

Transcription

1 E P CONCRETE BLOCK SEALER E P latest waterproofing product. Utilising advanced ACRYLIC technology, combined with Polyester Polymer. This formula outperforms all other aliphatic solutions currently in the market place. This latest product was specially developed for Concrete Blocks used in retaining wall construction. Some benefits are:- earth friendly chemistry High surface tension easier stain removal properties Two applications Non toxic non hazardous non flammable High chemical resistance Prevents fretting mortar Compatible with all conventional sealants, adhesives & paint Penetrates & protects from within. *Colour Milky White *State Liquid *Vapour (Air + 1) N/A *Specific Gravity: (Water = 1) 1.34@ 20 Degrees C. *Solubility in Water: Dilutable *Evaporation Rate: (BAC = 1) : Same as water. *Percent Volatile by Weight: N/A *ph: 7.0 *Boiling Point: 100 degrees Celsius. Water *Freezing Point: 0 degrees Celsius. Water Theoretical Coverage: 4 M2 per litre Method: Hand or Mechanical Sprayer. Consists of : 5, 20 and 200 Litre drum Shelf Life: 12 months minimum from date of manufacture when maintained in protected 5 38 degrees Celsius Enviropacific Pty Ltd 2/207 Bank Street East Victoria Park WA 6101 tel: enviropacific@oz .com.au. web:

2 E P CONCRETE BLOCK SEALER Is not a Surface coating although the acrylic will leave a slight sheen. Delivers easy cleaning and high tension for all surfaces Does NOT aerate. Insulates, hardens and waterproofs concrete blocks Causes a chemical reaction that solidifies the component parts of concrete and masonry into one single mass. Increases the tensile strength and prevents concrete from surface cracking, crumbling, dusting and rutting. Increasing the wearing quality. Enviropacific recommends Urethane sealers for floor and ceiling construction Joins

3 earth friendly chemistry Application Instructions 1. Apply EP Concrete Block Sealer once structure has been surveyed for any repairs required. 2. Use a low-pressure sprayer (Back -pack type) or any spray, operated at 20 Psi. back roll any excess into surface. 3. Spray entire surface area using approximately 1 Litre per 4 5 m2 apply second coat within 30 to 45 min, second coat is critical. 4. Critical that any missing mortar and cracks are repaired prior to sealing we recommend EP Bondex used in repair mortar. E P Concrete Block Sealer is best applied by spray method; this is not only fast and effective but also gives the correct application rate. Allow several days for completion of curing process and penetration. Allow to dry completely prior to the application of paint if that is desired. EP Concrete Block Sealer will provide a long lasting, problem free bond for paints, prevents peeling, blistering and cracking. E P Concrete Block Sealer will not harm glass, tile or aluminium.

4 For the Paint Trade EP Concrete Block Sealer will prevent and solve the age-old problem, which normally occurs whenever masonry is painted. Due to porosity of all masonry such as render, concrete, brick and terrazzo and its chemical composition, a long lasting surface bond with any surface coating is questionable and sometimes impossible. EP Concrete Block Sealer prevents Saponification so all paints last even longer than specified also paint is easier to apply and will achieve maximum m2 coverage. all pictures showing H- BLOCK construction.

5 Specifications 1 PRODUCT : EP Concrete Block Sealer 2. MANUFACTURER: Enviropacific Pty Ltd 2/207 Bank Street East Victoria Park WA enviropacific@oz .com.au web: 3. PRODUCT DESCRIPTION: EP Concrete Block Sealer is a non-toxic, non-caustic, non-flammable inorganic formulation with no equal. It permanently waterproofs and preserves. 4. PRODUCT USES: For industrial, commercial, and residential use, on concrete block work. H- Series blocks are best as they conform a continuous solid concrete structure once core filled. Series Concrete Blocks with solid ends are subject to minor cracks and shrinking mortar, extra care is required to provide a complete waterproofed structure. 5. JOB LIMITATIONS: Apply in good weather when air and surface temperature are above 7 Degrees C Temp must remain above 7 C for 24 hours after application. For optimum application properties, materials should be between 15 to 28 C prior to application. Maintain unused material in closed containers in protected storage at 4 to 38 C 6. SURFACE APPLICATION: DO NOT STORE IN DIRECT SUNLIGHT. Good surface preparation is essential to a satisfactory coating. Surfaces to be coated should be clean and dry. Remove all dirt, dust, oil, grease, rust, mildew and loose or cracked paint or other contamination by first cleaning with EP Cleaning Products. Rinse thoroughly and allow to dry.

6 NOTICE EP Concrete Block Sealer should not be applied to any surface that has had a previous coating of silicone, siloxene or solvent-based material. EP Concrete Block Sealer IS A PENETRATING PRODUCT If the applicator sees that is not being Absorbed. It should not be applied. Apply as instructed wet on wet multiple coats may be required sometimes two or more depending on block porosity. NOTICE : The information contained herein is based on data considered accurate; however NO Warranty is expressed or implied regarding the accuracy of this data. BUT maintains the product does perform to our standards, good industrial practices in block construction is paramount.

7 H-SERIES BLOCKS are the preferred type for waterproofing Once core filled they provide a continuous run of concrete Edge Type blocks are also preferred. Similar end results as H- Block once core filled. Series 200 etc. are NOT the preferred block to waterproof as the large end area of Concrete can dry out the mortar too quickly and leave a hair line crack. On the opposing end block, this causes no concerns in the structural strength Of the structure but can be a problem in waterproofing. In all cases the structure MUST be core filled with concrete slurry.