Special Provision No. 541S01 October OPSS 541, Construction Specifications for Chain Link Fence, is deleted and replaced with the following:
|
|
- Andrew Stokes
- 5 years ago
- Views:
Transcription
1 CHAIN LINK FENCE - Item No. GATES - Item No. Special Provision No. 541S01 October 1998 AMENDMENT TO OPSS 541, DECEMBER 1990 OPSS 541, Construction Specifications for Chain Link Fence, is deleted and replaced with the following: CONSTRUCTION SPECIFICATION FOR CHAIN LINK FENCE SCOPE This specification covers the requirements for the construction of chain link fence REFERENCES This specification refers to the following standards, specifications or publications: Ontario Provincial Standard Specifications, Construction: OPSS 904, January 1995 Construction Specification for Concrete Structures OPSS 180, January 1994 Management and Disposal of Excess Material Ontario Provincial Standard Specifications, Material: OPSS 1350, January 1995 Concrete (Materials and Production) Canadian General Standards Board: CAN/CGSB CAN/CGSB CAN/CGSB Fabric for Chain Link Fence Steel Framework for Chain Link Fence Gates for Chain Link Fence Canadian Standards Association: CSA-G162.1-M1977 CSA-G164-M1981 CSA-W59-M1989 Methods of Determining Mass of Coating on Zinc-Coated (Galvanized) Steel Wire Hot Dip Galvanizing of Irregularly Shaped Articles Welded Steel Construction (Metal Arc Welding) U.S. Federal Specification: FF-T-791b May 2, 1967 Turnbuckle October 1998 Page 1 of 8 SSP 541S01
2 DEFINITIONS For this specification the following definitions shall apply: Fence Post: An upright tubular or fabricated steel member for supporting fencing material. Line Posts: Fence posts spaced at regular intervals between terminal posts throughout each stretch of fence. Terminal Posts: Fence posts that include end, gate, corner and straining posts. End Posts: Fence posts positioned at the ends of a stretch of fence. Gates: Defined as the distance between the inside faces of the gate posts. Gate Posts: The two fence posts forming a gateway. Corner Posts: Fence posts positioned at corners and changes or direction greater than ten degrees. Straining Posts: Fence posts positioned at changes in grade greater than thirty degrees. Top Rail: A tubular or fabricated steel section continuously joined by means of sleeves or couplings throughout each stretch of fence extending between terminal posts. Brace Rail: A tubular or fabricated steel section used for bracing terminal posts. Diagonal Brace Wire: Wire used for bracing terminal posts. Top Wire: Wire installed at the top of the fence and extending throughout each stretch of fence between terminal posts. Bottom Wire: Wire installed at the bottom of the fence and extending throughout each stretch of fence between terminal posts. Fittings: Mechanical connections of various designs, shapes and metals to join fence components into an integral structure. Wire Ties: Wire used to tie chain link fence fabric to line posts, bottom wires and top rails or top wires. Knuckled: The type of selvage obtained by interlocking adjacent wire ends, in pairs, and then bending the wire ends back into a closed loop. Barbed: The type of selvage obtained by interlocking adjacent wire ends, in pairs, and then twisting the wire at least two turns with the wire ends above the twist. Barbed Wire: Twisted longitudinal wires, termed line wires, to which the barbs are attached. Non Shrink Cement Grout: means a bedding compound that is inert and free from shrinkage. October 1998 Page 2 of 8 SSP 541S01
3 MATERIALS Fence Fabric The steel wire for chain link fence fabric shall conform to CAN/CGSB The fabric shall be 1200 mm or 1800 mm wide with a uniform 50 mm diamond pattern chain link mesh closed at one edge by knuckling and at the other edge by twisting to form a barb. The fence wire shall be one of the following: 1. Type 1, Class A, Style 2, Grade Type 1, Class D, Style 1. or 3. Type 1, Class D, Style Type 2, Style 1. Chain link fence placed less than 10 m from the roadway shall be constructed with materials described in (1) or (2) above. Chain link fence placed more than 10 m from the roadway may be constructed with materials described in (1), (2), (3) or (4) above. The vinyl coating shall be grey in colour Posts and Rails All posts and rails shall be of galvanized steel pipe, and shall conform to CAN2/CGSB Diagonal Wire Brace, Top and Bottom Wires All wires shall be single strand galvanized steel wire conforming to CAN2/CGSB Vinyl coated top and bottom wires shall match the colour of the vinyl coated fence fabric Gates Gates shall be constructed from galvanized steel pipe frames and braces, conforming to CAN/CGSB All joints shall be electrically welded and hot-dip galvanized after welding, or otherwise treated by a procedure approved by the Authority as providing equivalent protection. All gates shall be supplied with galvanized malleable iron hinges, latch and latch catch and shall be capable of opening 180 degrees. Gate latches shall be suitable for the use of padlocks which can be attached and operated from either side of the gate. Gates shall be supplied completely assembled, including the fabric. The gate fabric and other components used on the gate shall match the adjacent fence fabric and be subject to the same quality requirements. October 1998 Page 3 of 8 SSP 541S01
4 Fittings and Accessories All required fittings and accessories and galvanizing of such material shall conform to CAN/CGSB All posts shall be fitted with waterproof metal caps designed to fit and fasten securely over the posts and carry either the top rail, or top wire as specified. Fasteners for attaching fence fabric to posts, bottom wire, top rail or top wire shall be 3.5 mm diameter aluminum or galvanized steel wire or 1.5 mm diameter stainless steel wire. Fasteners shall be coated if the entire system is coated. Stretcher bar fastening bands shall be fabricated from 3 x 19 mm steel or 5 x 19 mm aluminum Zinc Coating Zinc coatings shall conform to CAN2/CGSB-138.1, CAN2/CGSB and CAN/CGSB Concrete Concrete shall conform to OPSS 1350 for 20 MPa concrete Barbed Wire Barbed wire shall conform to CAN/CGSB Turnbuckles Turnbuckles shall be drop forged steel conforming to the U.S. Federal Specification FF-T-791b Type 1, Form 1, class 4, and shall be galvanized conforming to CSA G164-M. The average overall length shall be approximately 30 cm, with ends in the closed position. Bolt diameter shall be approximately 10 mm and shall be capable of taking up a minimum of 150 mm slack CONSTRUCTION Chain Link Fence The work shall include preparation of the site, installation of terminal posts, bracing, line posts, concrete footings, concrete anchors, pipe rails or top wire, fence fabric, bottom wire, restoration of the site, barbed wire and zinc coating repairs Site Preparation Prior to the erection of the chain link fence, the Contractor shall remove any debris and correct ground undulations to obtain a smooth, uniform gradient. The Contractor shall cut off at ground level, such trees, stumps and brush and remove and dispose of such logs, debris and overhanging branches which would interfere with the erection of the fence. October 1998 Page 4 of 8 SSP 541S01
5 Post Installation All posts shall be placed plumb and set accurately in line and position as specified by the Authority. Posts shall be cut to the required height above the ground to present a smooth and uniform profile. Line post spacing shall be equal horizontal distances. Horizontal deflections of 10 degrees or more shall be considered as corners with corner posts installed. Straining posts shall be installed at equal intervals not exceeding 150 m. Additional straining posts shall be installed where changes in vertical alignment exceed 30 degrees Posts on Concrete Barrier All posts installed on a concrete barrier shall be fastened to the concrete barrier using an adhesive anchor with a minimum pull out strength of 40 kn installed in accordance with manufacturers specifications. Each post shall be fabricated with a welded steel base plate grade 300 W and conforming to the contract drawings. All welds shall be to a low hydrogen classification conforming to CSA W59-M. Manual electrodes shall be E7015, E7016 or E7018. All welds shall be continuous Concrete Footings All posts set in earth, loose or friable rock, or where overburden to solid rock is 450 mm or greater, shall be set in concrete footings, shall be rough cast in the ground and domed above grade to shed water, and to the dimensions shown in the contract. Where the size of the hole exceeds the minimum dimensions of the footings, the Contractor shall either place the footing against undisturbed ground or shall backfill the hole with suitable earth material compacted to a density of 95% of maximum dry density and then bore a hole to the required minimum dimensions. All posts in solid rock or where overburden is less than 450 mm, holes for posts shall be drilled in the rock to a minimum depth of 380 mm with the diameter 25 mm greater than the outside diameter of the post. The annular space around the post shall be filled with non-shrink cement grout. For footings required in concrete, non shrink cement grout shall be placed as shown in the contract. Concrete placing, curing, testing and protection from the elements shall conform to OPSS Pipe Rails or Top Wires Pipe rails or top wires shall be fastened to post tops using waterproof caps Top and Bottom Wires Top and bottom wires shall be fastened to terminal posts with turnbuckles and centre bands. One turnbuckle is to be used between end, corner, straining or gate-posts. October 1998 Page 5 of 8 SSP 541S01
6 Fence Fabric Fence fabric shall not be installed until the concrete footings have cured for a minimum of five days. The stretched fabric shall be fastened to end, corner, gate and straining posts with steel stretcher bars and steel or aluminium stretcher bar bands. The longitudinal axis of the diamond pattern shall be perpendicular to the slope of the pipe rail. The fabric shall be placed on the side of the post nearest the roadway, with the barbed edge at the top. The fabric shall be securely fastened to the line posts, bottom wire and top rail or top wire with tie wires. The wire ties on the top and bottom wire shall have not less than two twists. The fabric shall not be fastened to any diagonal braces Site Restoration After fence erection, the Contractor shall clean and trim the site, and restore the ground to a neat and original condition existent prior to fencing operations Barbed Wire When specified, barbed wire shall be installed using the barbed wire arm fitting. The barbed wire arm shall be installed with the arm pointing away from the roadway Zinc Coating Repairs All abraded and damaged galvanized surfaces shall be cleaned and painted. Damaged areas shall be thoroughly wire brushed and all loose and cracked zinc coating removed, after which the cleaned area shall be painted with two coats of a zinc pigmented paint approved by the Authority for this purpose Bracing A pipe or wire brace shall be placed diagonally across the panel at all end and gate posts. Corner and straining posts shall be supported with diagonal braces placed on both sides of the post. In all cases, the higher end of the diagonal brace shall be connected at the terminal post. End fittings for pipe braces shall be secured by a 6 mm bolt placed through the brace and fitting at both ends Gates The work shall include the installation of each size and type of gate with the necessary fittings and hardware, including construction of the gate stop in the case of double gates Gate Installation Gates shall be constructed with the fabric on the side farthest from the roadway, with the barbed edge at the top. All gates shall have a chain hook to hold gates open and double gates shall have a steel gate centre rest with drop bolt for the closed position. October 1998 Page 6 of 8 SSP 541S01
7 The surface grade within the required gate sweep area shall be low enough to permit free movement of the gate Management and Disposal of Excess Material Management and disposal of excess material shall be according to OPSS QUALITY CONTROL/ASSURANCE Material The Contractor shall upon request furnish certification of compliance with the material specifications. The Contract Administrator may test any samples supplied at the Contractor's expense, to ensure compliance with the material specifications. Products, represented by the samples, not in compliance shall be removed from the Contract site and replaced at the Contractors expense Construction The Contractor shall certify that the installation complies with the standards and specifications as detailed in the contract. The Contract Administrator may perform a spot visual inspection to determine conformance with the workmanship, design and dimensional requirements of this specification, including but not limited to the following. The fence fabric shall be stretched taut and securely fastened to the posts, top rail or wire, and the bottom wire. The top of the fence shall follow approximately the profile of the natural ground, or grade line, if specified. All posts shall be true to alignment and plumb. Terminal posts shall be installed at locations as indicated in this specification. Gates shall move freely. Failure to conform to the specifications will result in a complete inspection of the installation, and removal or replacement of all defective workmanship or materials. The inspection as well as any required removals or replacement shall be at the Contractors expense. Inspection costs will be 40 dollars per hour with a minimum charge of 500 dollars Warranty The Contractor shall be responsible for the proper performance of the Work only to the extent that the design and specifications permit such performance. Subject to the previous paragraph the Contractor shall correct promptly, at no additional cost to the Owner, defects or deficiencies in the work which appear prior to and during the period of 12 months from the date of substantial performance of the Work, as set out in the Certificate of Substantial Performance of the work, or where there is no Substantial Performance Certificate, 12 months from date of Completion of the Work as set out in the Completion Certificate. The Owner will promptly give the Contractor written notice of observed defects or deficiencies. Failure to correct deficiencies within 14 calendar days of receiving notice will result in the Owner having the work done with cost recovery from the Contractor. The Contractor shall correct or pay for damage resulting from corrections made under the requirements of the above paragraph of this subsection. October 1998 Page 7 of 8 SSP 541S01
8 MEASUREMENT FOR PAYMENT Actual Measurement Chain Link Fence Measurement will be made in metres, following the contour of the ground, of the actual length of fence erected with no deduction for gate openings Gates Measurement will be made in units of each, regardless of the size and type of gate erected. Double gates will be counted as one gate Plan Quantity Measurement Measurement is by Plan Quantity, as may be revised by Adjusted Plan Quantity, for the horizontal length, in metres, along the centerline of fence, including gate openings BASIS OF PAYMENT Chain Link Fence - Item Gates - Item Payment at the contract price for the above item(s) shall be full compensation for all labour, equipment and material required to do the work. October 1998 Page 8 of 8 SSP 541S01
CONSTRUCTION SPECIFICATION FOR CHAIN LINK FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 541 DECEMBER 1990 CONSTRUCTION SPECIFICATION FOR CHAIN LINK FENCE 541.01 SCOPE 541.02 REFERENCES 541.03 DEFINITIONS 541.05 MATERIALS TABLE OF CONTENTS
More informationCONSTRUCTION SPECIFICATION FOR CHAIN-LINK FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 541 NOVEMBER 2005 CONSTRUCTION SPECIFICATION FOR CHAIN-LINK FENCE TABLE OF CONTENTS 541.01 SCOPE 541.02 REFERENCES 541.03 DEFINITIONS 541.04 SUBMISSION
More informationCONSTRUCTION SPECIFICATION FOR CHAIN-LINK FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 772 NOVEMBER 2010 CONSTRUCTION SPECIFICATION FOR CHAIN-LINK FENCE TABLE OF CONTENTS 772.01 SCOPE 772.02 REFERENCES 772.03 DEFINITIONS 772.04 DESIGN
More informationCONSTRUCTION SPECIFICATION FOR CHAIN-LINK FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 772 NOVEMBER 2017 (Formerly OPSS 772, November 2012) Note: The PROV published in November 2017 replaces OPSS 772 COMMON, November 2012 with no technical
More informationAmendment to OPSS 772 (Nov 2012) Construction Specification for Chain-Link Fence
Engineering and Construction Services Division Standard Specifications for Road Works TS 772 April 2014 Amendment to OPSS 772 (Nov 2012) Construction Specification for Chain-Link Fence OPSS 772.05 OPSS
More informationSpecial Provision No. 540S01 March OPSS 540, Construction Specification for Highway Fence, is deleted and replaced with the following:
HIGHWAY FENCE - Item No. BRACE PANELS - Item No. GATES - Item No. Special Provision No. 540S01 March 2006 AMENDMENT TO OPSS 540, MAY 1988 OPSS 540, Construction Specification for Highway Fence, is deleted
More informationMATERIAL SPECIFICATION FOR CHAIN-LINK FENCE COMPONENTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1541 NOVEMBER 2005 (Reissued November 2010) MATERIAL SPECIFICATION FOR CHAIN-LINK FENCE COMPONENTS TABLE OF CONTENTS 1541.01 SCOPE 1541.02 REFERENCES
More informationCW 3550 Chain Link and Drift Control Fence TABLE OF CONTENTS
January 2014 SPECIFICATION CW 3550 R3 CW 3550 Chain Link and Drift Control Fence TABLE OF CONTENTS 1. GENERAL CONDITIONS... 1 3. DESCRIPTION... 1 5. MATERIALS... 1 5.1 Drift Control Fence... 1 5.1.1 Approved
More informationCONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 771 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE TABLE OF CONTENTS 771.01 SCOPE 771.02 REFERENCES 771.03 DEFINITIONS 771.04 DESIGN
More informationITEM 555 CHAIN LINK FENCING
ITEM 555 AFTER MARCH 1, 2012 CHAIN LINK FENCING 555.1 Description. This item shall govern for furnishing the quantities of chain link fencing and gates as shown on the plans, including all posts, bracing
More informationCONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 540 APRIL 2007 CONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE TABLE OF CONTENTS 540.01 SCOPE 540.02 REFERENCES 540.03 DEFINITIONS 540.04 SUBMISSION
More informationCITY OF MOUNT DORA LIFT STATION CHAINLINK FENCE AND GATE SPECIFICATIONS
CITY OF MOUNT DORA LIFT STATION CHAINLINK FENCE AND GATE SPECIFICATIONS PART 1 - GENERAL 1.01 SUMMARY A. Section Includes furnishing and installing chain-link fabric fence, gate, and appurtenances. 1.02
More informationSECTION CHAIN LINK FENCES
SECTION 02 44 40 PART 1 - GENERAL 1.1 DESCRIPTION A. Work included: Provide chain link fence system where shown on the Drawings, as specified herein, and as needed for a complete and proper installation.
More informationCONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 771 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE TABLE OF CONTENTS 771.01 SCOPE 771.02 REFERENCES 771.03 DEFINITIONS 771.04
More informationCONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 771 NOVEMBER 2010 CONSTRUCTION SPECIFICATION FOR STANDARD HIGHWAY FENCE TABLE OF CONTENTS 771.01 SCOPE 771.02 REFERENCES 771.03 DEFINITIONS 771.04
More informationSECTION 1208 CHAIN LINK FENCING DESCRIPTION
SECTION 1208 CHAIN LINK FENCING 1208-1 DESCRIPTION This item covers the requirements for furnishing materials and constructing new chain link fences and gates in accordance with the details included herein
More informationSECTION 2831 ITEM F-162 CHAIN-LINK FENCES
SECTION 2831 ITEM F-162 CHAIN-LINK FENCES PART 1 - GENERAL 1.1 DESCRIPTION. This item shall consist of furnishing and erecting a chain-link fence in accordance with these specifications and the details
More informationSECTION CHAIN LINK FENCES AND GATES (GALVANIZED) A. Fence framework, fabric, gates, and accessories.
SECTION 02830 CHAIN LINK FENCES AND GATES (GALVANIZED) 1.0 GENERAL 1.1 Section Includes A. Fence framework, fabric, gates, and accessories. B. Excavation for post bases; concrete footing for posts. C.
More informationCONSOLIDATED EDISON COMPANY OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY DISTRIBUTION ENGINEERING DISTRIBUTION EQUIPMENT
CONSOLIDATED EDISON COMPANY OF NEW YORK, INC. 4 IRVING PLACE NEW YORK, NY 10003 DISTRIBUTION ENGINEERING DISTRIBUTION EQUIPMENT SPECIFICATION EO-1124 REVISION 3 November 2013 EFFECTIVE DATE November 11,
More informationCONSTRUCTION SPECIFICATION FOR EXPANDED METAL ANTI-GLARE SCREEN
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 791 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR EXPANDED METAL ANTI-GLARE SCREEN TABLE OF CONTENTS 791.01 SCOPE 791.02 REFERENCES 791.03 DEFINITIONS
More informationSECTION CHAIN LINK FENCING
SECTION 02835 - CHAIN LINK FENCING 1.0 GENERAL 1.1 Furnish and install chain link fencing complete in place with gates and accessories as specified herein and as shown on the Contract Drawings. 1.2 Reference
More informationSECTION CHAIN LINK FENCES AND GATES (PARK)
SECTION 02821 CHAIN LINK FENCES AND GATES (PARK) PART I GENERAL 1.1 SECTION INCLUDES A. Installation of chain link fences, and gate units provided by single source including erection accessories, fittings,
More informationSECTION CHAIN LINK FENCING
Section 02444 1 SECTION 02444 CHAIN LINK FENCING PART 1 - GENERAL 1.01 DESCRIPTION A. Requirement. Under these specifications, the Contractor shall furnish all materials, labor, tools, and equipment required
More informationSECTION CHAIN LINK FENCES AND GATES
SECTION 32 31 13 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.1 SUMMARY A. This Section includes materials applicable for commercial/industrial and security vinyl coated chain link fence and framework.
More informationSECTION CHAIN LINK FENCES AND GATES
SECTION 32 31 13 SPEC WRITER NOTES: Use this section only for NCA projects. Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section
More informationCHAIN LINK FENCES AND GATES
SECTION 02831 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.01 SUMMARY A. Alternate Material for Fence Post and Framing Material: Where schedule 40 galvanized steel is specified, the following will be accepted:
More informationCHAIN LINK FENCES AND GATES
SECTION 02831 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.01 REFERENCES AND CODES A. Florida Department of Education, Office of Educational Facilities - State Requirements for Educational Facilities -
More informationSECTION CHAIN LINK FENCES AND GATES
SECTION 02831 CHAIN LINK FENCES AND GATES PART 1 GENERAL 1.01 REFERENCES AND CODES A. Florida Department of Education, Office of Educational Facilities - State Requirements for Educational Facilities -
More informationTITLE: CAMP JOHNSON OVERPASS / HWY 17 BYPASS SECURITY FENCE UPGRADES
CONTRACT # N40085-15B-0457 PROJECT # 15R036CN MACC # 15-0457 MAXIMO# 4608934 TITLE: CAMP JOHNSON OVERPASS / HWY 17 BYPASS SECURITY FENCE UPGRADES ATTACHMENTS: 1. 15-0457 CJ OVERPASS SECURITY UPGRADES Site
More informationMO: Tl RSA: 1406B
MO: Tl425-02 SECTION 323113- CHAIN LINK FENCES AND GATES PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationCITY OF FRIENDSWOOD TECHNICAL SPECIFICATIONS DOCUMENT 00085B ADDENDUM ADDENDUM NO. 1
ADDENDUM Date of Addendum: December 30 th, 2015 PROJECT NAME: Fencing for Sportspark PROJECT NO: GO1507 BID DATE: Tuesday, January 5 th, 2016 FROM: City of Friendswood Department of Public Works 1306 Deepwood
More informationColorado River Aqueduct Pumping Plants 230 kv Disconnect Switches Replacement
DATE: July 15, 2011 ADDENDUM NUMBER: 2 MODIFYING: Specifications No. 1698 PROJECT: Colorado River Aqueduct Pumping Plants 230 kv Disconnect Switches Replacement BID TIME AND DATE: 2:00 p.m., July 19, 2011
More informationSECTION 410 FENCES All materials shall be new and without flaws or defects of any type GENERAL
SECTION 410 FENCES 410.1 GENERAL This work shall consist of the construction of fences and gates in substantial compliance with the specifications, lines, and grades shown on the plans or established by
More informationCONSTRUCTION SPECIFICATION FOR SITE RESTORATION FOR UNDERGROUND UTILITIES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 507 JULY 1991 CONSTRUCTION SPECIFICATION FOR SITE RESTORATION FOR UNDERGROUND UTILITIES 507.01 SCOPE 507.02 REFERENCES 507.03 Not Used 507.04 Not Used
More informationCONSTRUCTION SPECIFICATION FOR NOISE BARRIER SYSTEMS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 760 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR NOISE BARRIER SYSTEMS TABLE OF CONTENTS 760.01 SCOPE 760.02 REFERENCES 760.03 DEFINITIONS 760.04 DESIGN
More information1. Fence and gate posts, rails, and fittings. 2. Chain-link fabric, reinforcements, and attachments.
SECTION 323113 - CHAIN LINK FENCES AND GATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationAdvisory Circular PAGECONTROLCHART. Remove Pages Dated II Inscr t Pages Dated l/2/ thru 258-l 7/6/ l/2/90
U.S. Department of Transportation Federal Aviation Administration Advisory Circular Subject: Change 8 to STANDARDS FOR SPECIFYING CONSTRUCTION OF AIRPORTS Date: 7/6/94 AC No: 150/53701OA Initiated by:
More informationSECTION 1043 FENCE MATERIAL
SECTION 1043 FENCE MATERIAL 1043.1 Scope. This specification covers the material required in the construction of chainlink fence and woven wire fence. 1043.2 Basis of Acceptance. The basis of acceptance
More informationSpecial Provision No. 799F01 March 2012 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF NOISE BARRIER TABLE OF CONTENTS
... m NOISE BARRIER - Item No.... m NOISE BARRIER INCLUDING PRECAST NOISE/TRAFFIC BARRIER - Item No.... m NOISE BARRIER ON STRUCTURES - Item No.... m SALVAGEABLE NOISE BARRIER - Item No.... m SALVAGEABLE
More informationA NEW PRE-K BUILDING FOR BIG SPRING LAKE KINDERGARTEN SCHOOL FOR THE ALBERTVILLE CITY BOARD OF EDUCATION ALBERTVILLE, ALABAMA
McKee and Associates Architecture and Interior Design Addendum No. FOUR Date: 09.24.18 Project: A NEW PRE-K BUILDING FOR BIG SPRING LAKE KINDERGARTEN SCHOOL FOR THE ALBERTVILLE CITY BOARD OF EDUCATION
More informationSECTION FENCING. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 323100 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More informationSECTION CHAIN LINK FENCES AND GATES
SECTION 32 31 13 CHAIN LINK FENCES AND GATES SPEC WRITER NOTE: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this section in specifying permanent chain
More informationSECTION CHAIN-LINK FENCES AND GATES 02821/1
SECTION 02821 - CHAIN-LINK FENCES AND GATES 02821/1 PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Chain-Link Fences: 2. Gates: horizontal slide or swing. 3. Fences installed where
More informationSpecial Provision No. 599F01 May 2004 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF NOISE BARRIER TABLE OF CONTENTS
... m NOISE BARRIER - Item No.... m NOISE BARRIER INCLUDING PRECAST NOISE/TRAFFIC BARRIER - Item No.... m NOISE BARRIER ON STRUCTURES - Item No.... m SALVAGEABLE NOISE BARRIER - Item No.... m SALVAGEABLE
More informationMATERIAL SPECIFICATION FOR STANDARD HIGHWAY FENCE COMPONENTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1540 NOVEMBER 2012 MATERIAL SPECIFICATION FOR STANDARD HIGHWAY FENCE COMPONENTS TABLE OF CONTENTS 1540.01 SCOPE 1540.02 REFERENCES 1540.03 DEFINITIONS
More informationHouston Community College 3200 Main Parking Garage November 15, 2010 Houston Community College
SECTION 323113 - CHAIN LINK FENCES AND GATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSpecial Provision No. 799S15 December 2016
HIGH TENSION THREE CABLE GUIDE RAIL SHOULDER INSTALLATION - Item No. HIGH TENSION THREE CABLE GUIDE RAIL SLOPE INSTALLATION - Item No. HIGH TENSION CABLE GUIDE RAIL TERMINAL SYSTEM - Item No. Special Provision
More informationSECTION ORNAMENTAL WELDED STEEL FENCING
SECTION 032300 ORNAMENTAL WELDED STEEL FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationMATERIAL SPECIFICATION FOR STANDARD HIGHWAY FENCE COMPONENTS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 1540 NOVEMBER 2016 MATERIAL SPECIFICATION FOR STANDARD HIGHWAY FENCE COMPONENTS TABLE OF CONTENTS 1540.01 SCOPE 1540.02 REFERENCES 1540.03 DEFINITIONS
More informationSECTION ORNAMENTAL ALUMINUM FENCING
SECTION 032300 ORNAMENTAL ALUMINUM FENCING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationTOWN OF OSOYOOS PERIMETER FENCING OSOYOOS LANDFILL
TOWN OF OSOYOOS PERIMETER FENCING OSOYOOS LANDFILL CONTRACT DOCUMENTS AND SPECIFICATIONS TRUE Consulting August 2011 Job No. 302-706 PLANHOLDER REGISTRATION FORM Request for Tender No. 302-706 PERIMETER
More informationCONSTRUCTION SPECIFICATION FOR FOOTINGS AND PADS FOR ELECTRICAL EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 616 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR FOOTINGS AND PADS FOR ELECTRICAL EQUIPMENT TABLE OF CONTENTS 616.01 SCOPE 616.02 REFERENCES 616.03
More informationKANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, EDITION 2007
Sheet 1 of 7 KANSAS DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION TO THE STANDARD SPECIFICATIONS, EDITION 2007 Delete SECTION 828 and replace with the following: SECTION 828 FENCING 828.1 DESCRIPTION
More informationANTI RAM SECURITY CHAIN LINK FENCE - 4, MPH SECTION
ANTI RAM SECURITY CHAIN LINK FENCE - 4,000 LB @ 20 MPH SECTION 32 31 13.53 2015
More informationA. Product Data shall be provided for each type of product indicated.
32 31 13 CHAIN LINK FENCES AND GATES SECTION 1 GENERAL 1.1 SUMMARY This Section includes the following: 1. Chain Link Fences 2. Gates for Chain Link Fences. See electrical specifications for electrical
More informationMERCHANTS METALS. A. ASTM F552 Standard Terminology Relating to Chain Link Fencing
MERCHANTS METALS SECTION 32 31 13 COLORBOND CHAIN LINK FENCE AND GATES 2014 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance requirements,
More informationCONSTRUCTION SPECIFICATION FOR FOOTINGS AND PADS FOR ELECTRICAL EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.MUNI 616 APRIL 2018 CONSTRUCTION SPECIFICATION FOR FOOTINGS AND PADS FOR ELECTRICAL EQUIPMENT TABLE OF CONTENTS 616.01 SCOPE 616.02 REFERENCES 616.03 DEFINITIONS
More informationCONSTRUCTION SPECIFICATION
CAPRICORN MUNICIPAL DEVELOPMENT GUIDELINES BOUNDARY FENCING C265 CONSTRUCTION SPECIFICATION CAPRICORN MUNICIPAL DEVELOPMENT GUIDELINES C265 ISSUE: NO:1 October 2007 TABLE OF CONTENTS CLAUSE CONTENTS PAGE
More informationMICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LOW-TENSION CABLE BARRIER. OPR:CT 1 of 5 APPR:JAR:DBP: FHWA:APPR:
MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR LOW-TENSION CABLE BARRIER OPR:CT 1 of 5 APPR:JAR:DBP:09-07-11 FHWA:APPR:09-07-11 a. Description. This work consists of furnishing and installing
More informationBear Exhibit Fence Upgrades. The following modifications are hereby made part of the contract documents:
ADDENDUM TO BID T2017-04 Metropolitan Park District Department of Planning, Design and Development 4702 South 19 th Street Tacoma WA 98405 Date Prepared: November 17, 2017 Bid Number: T2017-04 Addendum
More informationA. ASTM A121 Specification for Metallic-Coated Carbon Steel Barbed Wire. B. ASTM A392 Specification for Zinc-Coated Steel Chain-Link Fence Fabric
SECTION 32 31 13 CHAIN LINK FENCE AND GATES 2015 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. DIVISION 01 - GENERAL REQUIREMENTS: Drawings, quality, product and performance requirements, general and supplemental
More informationAMERICAN SAMOA POWER AUTHORITY Materials Management Office INVITATION FOR BIDS ( IFB ) EAST SIDE WELLS-BOOSTERS SECURITY FENCE REPLACEMENT
AMERICAN SAMOA POWER AUTHORITY Materials Management Office INVITATION FOR BIDS ( IFB ) EAST SIDE WELLS-BOOSTERS SECURITY FENCE REPLACEMENT Issuance Date: March 24, 2016 Closing Date: March 31, 2016 APPROVED
More informationCONSTRUCTION SPECIFICATION FOR POLE ERECTION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 SEPTEMBER 1993 CONSTRUCTION SPECIFICATION FOR POLE ERECTION 615.01 SCOPE 615.02 REFERENCES 615.05 MATERIALS TABLE OF CONTENTS 615.05.01 Concrete.02
More informationCONSTRUCTION SPECIFICATION
CAPRICORN MUNICIPAL DEVELOPMENT GUIDELINES BOUNDARY FENCING C265 CONSTRUCTION SPECIFICATION CAPRICORN MUNICIPAL DEVELOPMENT GUIDELINES C265 ISSUE: NO:2 July 2018 TABLE OF CONTENTS CLAUSE CONTENTS PAGE
More informationCONSTRUCTION SPECIFICATION FOR STEEL BEAM GUIDE RAIL AND CABLE GUIDE RAIL
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 552 NOVEMBER 2002 CONSTRUCTION SPECIFICATION FOR STEEL BEAM GUIDE RAIL AND CABLE GUIDE RAIL TABLE OF CONTENTS 552.01 SCOPE 552.02 REFERENCES 552.03
More informationCONSTRUCTION SPECIFICATION FOR CONCRETE BARRIERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 553 FEBRUARY 1991 CONSTRUCTION SPECIFICATION FOR CONCRETE BARRIERS 553.01 SCOPE 553.02 REFERENCES 553.03 DEFINITIONS TABLE OF CONTENTS 553.04 SUBMISSION
More informationMETALS Commissioning of Metals Structural Steel Framing Steel Studs... 2
~ 05-1 ~ 05 00 00 Metals 05 00 00 METALS... 2 05 08 00 Commissioning of Metals... 2 05 12 00 Structural Steel Framing... 2 05 12 30 Steel Studs... 2 05 45 00 METAL SUPPORT ASSEMBLIES... 2 05 50 00 METAL
More informationSpecial Provision No. 915S03 December References, Materials, Construction, and Quality Assurance for Sign Support Structures
STEEL MONOTUBE OVERHEAD SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. STEEL COLUMN NON-BREAKAWAY SIGN SUPPORT STRUCTURES - Item No. CANTILEVER STATIC SIGN
More informationPASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 02821 - CHAIN-LINK FENCES AND GATES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationCONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 MARCH 1993 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER 602.01 SCOPE 602.02 REFERENCES 602.05 MATERIALS TABLE OF CONTENTS
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION CHAIN LINK FENCING
PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. Requirements vary. A/E shall consult with DPS project manager to determine extent and type of permanent site fencing to be employed. B. Provide
More informationCONSTRUCTION SPECIFICATION FOR ERECTION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not Used 615.04
More informationCONSTRUCTION SPECIFICATION FOR GROUNDING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 609 NOVEMBER 2001 CONSTRUCTION SPECIFICATION FOR GROUNDING TABLE OF CONTENTS 609.01 SCOPE 609.02 REFERENCES 609.03 DEFINITIONS - Not Used 609.04 DESIGN
More informationCONSTRUCTION SPECIFICATION FOR STEEL BEAM GUIDE RAIL AND CABLE GUIDE RAIL
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.MUNI 721 NOVEMBER 2014 CONSTRUCTION SPECIFICATION FOR STEEL BEAM GUIDE RAIL AND CABLE GUIDE RAIL TABLE OF CONTENTS 721.01 SCOPE 721.02 REFERENCES 721.03
More informationSECTION 2 DIVISION 05 METALS
SECTION 2 DIVISION 05 METALS DIVISION 5 - METALS Note: This is a guide for Designers only. Contents shall not be used in lieu of specifications as part of the Designer s Contract Documents. GENERAL DESIGN:
More informationCONSTRUCTION SPECIFICATION FOR SITE RESTORATION FOLLOWING INSTALLATION OF PIPELINES, UTILITIES, AND ASSOCIATED STRUCTURES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 492 NOVEMBER 2010 CONSTRUCTION SPECIFICATION FOR SITE RESTORATION FOLLOWING INSTALLATION OF PIPELINES, UTILITIES, AND ASSOCIATED STRUCTURES TABLE OF
More informationCONSTRUCTION SPECIFICATION FOR POLE ERECTION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2006 CONSTRUCTION SPECIFICATION FOR POLE ERECTION TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not Used 615.04
More informationTS 803 DUCTS DUCT INSTALLATION, PROTECTION AND MARKING WITHIN A TRENCH OPEN TRENCH DUCT INSTALLATION PROFILE
TORONTO TRANSPORTATION March 2012 TS 803 DUCTS TABLE OF CONTENTS 1. DRAWINGS TTD 803.001 TTD 803.010 DUCT INSTALLATION, PROTECTION AND MARKING WITHIN A TRENCH OPEN TRENCH DUCT INSTALLATION PROFILE 2. CONSTRUCTION
More informationCONSTRUCTION SPECIFICATION FOR ERECTION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 NOVEMBER 2008 (Reissued November 2010) CONSTRUCTION SPECIFICATION FOR ERECTION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03
More informationSECTION WELDED STEEL PICKET FENCE. 1. Fusion welded and rackable ornamental steel picket fence system.
PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Fusion welded and rackable ornamental steel picket fence system. B. Related sections: 1. Section 03310 Concrete Work for post support. 2. Section 09960
More informationA. Coordinate chain link fence & gate work with work before and after. See especially: 1. Bollards on worksite that are more than 10 ft from fence.
02830 CHAIN LINK FENCES AND GATES ************************************************************************************************************ Specifier: This section replaces 02831 (2004). It reflects
More informationUFGS (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-32 31 13 (November 2016) Change 1-05/17 ----------------------------- Preparing Activity: NASA Superseding UFGS-32 31 13 (August 2010) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1850 NOVEMBER 2007 MATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS TABLE OF CONTENTS 1850.01 SCOPE 1850.02 REFERENCES 1850.03 DEFINITIONS
More informationMATERIAL SPECIFICATION FOR FRAMES, GRATES, COVERS, AND GRATINGS
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 1850 APRIL 2018 (Formerly OPSS 1850, April 2013) Note: The PROV published in April 2018 replaces OPSS 1850 COMMON, April 2013 with no technical content
More informationSECTION HIGH-SECURITY CHAIN LINK FENCES AND GATES
SECTION 323113.53 - PART 1 - GENERAL 1.1 SUMMARY A. Section includes high-security chain-link fences and motor-operated, horizontal slide gates. 1.2 PERFORMANCE REQUIREMENTS A. Delegated Design: Design
More informationFOR PROJECTS INITIATED AFTER NOVEMBER 1, 2008 REVISION 7 ITEM 516 INSTALLATION OF FLEX BEAM GUARDRAIL
AFTER NOVEMBER 1, 2008 ITEM 516 INSTALLATION OF FLEX BEAM GUARDRAIL 516.1 Description. This item shall govern for furnishing and placing 10 or 12 gauge galvanized flex beam guardrail, complete with timber
More informationSECTION ALUMINUM HANDRAIL SYSTEMS
SECTION 05520 ALUMINUM HANDRAIL SYSTEMS PART 1 - GENERAL 1.01 SUMMARY A. Section includes aluminum handrails and railings. B. Related Work: 1. Section 03300 - Cast-in-Place Concrete C. References: 1. American
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO MITCHELL-HOLLINGSWORTH NURSING & REHAB ADPH #B
SECTION 05 5213 - PIPE RAILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationMATERIAL SPECIFICATION FOR PRECAST REINFORCED CONCRETE BOX CULVERTS AND BOX SEWERS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 1821 APRIL 2004 MATERIAL SPECIFICATION FOR PRECAST REINFORCED CONCRETE BOX CULVERTS AND BOX SEWERS TABLE OF CONTENTS 1821.01 SCOPE 1821.02 REFERENCES
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-32 31 26 (April 2008) -------------------------- Preparing Activity: USACE Superseding UFGS 32 31 26 (January 2008) UNIFIED FACILITIES GUIDE SPECIFICATIONS References
More informationREQUEST FOR BIDS Public Works Contract SPECIFICATIONS FOR FENCE REPAIRS AND REPLACEMENT
REQUEST FOR BIDS Public Works Contract SPECIFICATIONS FOR FENCE REPAIRS AND REPLACEMENT DATE OF RELEASE: DATE OF CLOSING: RFB ID: July 18, 2013 at 8:00 am (cst) August 5, 2013 at 4:30 pm (cst) 0718201301
More informationCOATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006
COATING NEW STRUCTURAL STEEL SIGN SUPPORT STRUCTURES - Item No. Special Provision No. 911S09 November 2006 Amendment to OPSS 911, November 2004 for hot dip galvanizing and subsequent painting, where required,
More informationCONSTRUCTION SPECIFICATION FOR INSTALLATION OF POLES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 615 April 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF POLES TABLE OF CONTENTS 615.01 SCOPE 615.02 REFERENCES 615.03 DEFINITIONS - Not
More information1. Temperature Change: 120 deg F (67 deg C), ambient; 180 deg F (100 deg C), material surfaces.
SECTION 05500- METAL FABRICATIONS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCONSTRUCTION SPECIFICATION FOR CONCRETE SIDEWALK AND CONCRETE RAISED MEDIAN INDEX TS SCOPE...3 TS DEFINITIONS...3
CITY OF TORONTO TS 3.70 TRANSPORTATION SERVICES STANDARD CONSTRUCTION SPECIFICATIONS June 2001 CONSTRUCTION SPECIFICATION FOR CONCRETE SIDEWALK AND CONCRETE RAISED MEDIAN INDEX TS 3.70.01 SCOPE...3 TS
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationENGINEERING, CONSTRUCTION AND MATERIAL STANDARD FOR FENCING AND GATES ORIGINAL EDITION MAY. 1997
ENGINEERING, CONSTRUCTION AND MATERIAL STANDARD FOR FENCING AND GATES ORIGINAL EDITION MAY. 1997 This standard specification is reviewed and updated by the relevant technical committee on Jul. 2002. The
More informationSport Systems Canada Inc. Section Angle Framed Bleachers Page 1
Page 1 Part 1 GENERAL.1.1 Section Includes.1 Design, fabrication, engineering, and installation of continuous angle framed bleacher assembly, including the following:.1 Foundations.2 Galvanized steel framing
More information