MARBLE / STONE PROJECT NAME: HARD ROCK HOTEL & CASINO TULSA DATE: MAY 20, 2011 JOB #: 91002
|
|
- Jack Bridges
- 5 years ago
- Views:
Transcription
1 MA-102 Coverall Stone Inc. CUT PEBBLE TILE th Ave. S. #209 Seattle, WA FAX Name: Cut Pebble Tile Color: Cut Amber PT-CP-AM Size: 12 x 12 Mesh-backed Thickness: 11-13mm +/- Weight: +/- 4 lbs. / sq. ft. Packing: 11 sq. ft./ box Grout Color: Mapei #44 Pale Umber with matte sealer Use standard thin-set and sanded grout for installation. Stone to be sealed with clear matte sealer. Buffet Remodel Inset at Front of Food Service Counter and POS Stations
2 The pebbles and stones are a natural product, meaning that not two pieces are exactly alike. It is not unusual to find veins and lines of separation in the pebbles. This is generally a desired feature of the product. BEFORE YOU BEGIN Before installing the tiles, inspect your tiles for algae or yellow discoloration. This is the result of climate change and can easily be remedied by wetting the tiles and placing them outdoors in direct sunlight for eight hours. SUBSTRATES All substrates should be flat, clean, dry, free of any contamination, and firmly fixed in place. Deflections should be a maximum of 1/360 of the span for walls and floors. Use in wet areas requires special attention involving appropriate substrates e.g.- concrete, cement boards (compressed sheet) and treated plywood. Always use reinforced waterproof membranes. When used for flooring make sure the fall to drainage point is not less than 2 inches. WATERPROOF MEMBRANES Waterproof membranes prevent the leakage of water through subflooring. Attention must be paid to carrying the membrane up the wall, outside of shower boxes, installation of bond breakers, and sealing around penetrations. Membrane systems should be used in all wet areas including exterior suspended decking. Some systems involve the use of a primer. ADHESIVE Use a product that is suitable for your project. The manufacturers literature will explain if the adhesive is to be used for interior or exterior use, or for walls or floors. Generally, a cement-based adhesive is suitable on masonry substrates where no movement is anticipated. If slight movement could occur because of pedestrian or thermal loads, a modified cement adhesive should be used as a minimum (probably 2-part.) It is important that each pebble be firmly imbedded in the adhesive. Use a product suitable for application with a 1 /4" notched trowel, and apply no more than three square feet of adhesive at a time. LAYING AND JOINT HIDING Interlocking pebble tiles are designed to create a seamless look. It is a good idea to lay the tiles on the ground first to arrange desired alignment and layout before using adhesive. IT IS CRUCIAL TO ALTERNATE AND STAGGER the pieces in each row so the seams do not line up from one row to the next. This will ensure that the seams do not show. The best way to do this is to start with the tile edge against the wall. In the next row above it, cut a piece in half to begin and then continue with full pieces. Natural Stone Field Tile Guidelines For Installation For the next row begin with a full piece etc.. Butt tiles together and do not leave the traditional 1 /4" to 3 /8" grout gap that is left for laying traditional ceramic tiles. If you are working with corners (such as in a shower), always start with the corner first and work your way out from there. You will need to order extra pieces from which you can pull pebbles to fill in gaps. For example, when a piece is flush against a wall, there will be a staggered or ragged piece. Simply pull pebbles off an extra piece, dab thinset onto the back of the loose pebble and press it into place in the needed areas between the tile and wall. GROUTING The grout should be suitable for joints up to 1 /2"wide whether it is for internal or external use. Generally, grouts are mixed with water, but an acrylic or latex grout is recommended to prevent cracking in case of slight movement in the tiled area. Wait no longer than the period recommended by the manufacturer before grouting to minimize dirt ingress between the pebbles, and the possible dislodgment of the pebbles. It is recommended that the grout level not be higher than the maximum girth of the pebble to ensure that as much of the pebble is seen as possible. CURVED SURFACES The pebble tiles can be easily fitted around a gently curved surface such as a column. If the sheet is curved around a right angle, some pebbles will need to be plucked off the mat where they are distorted and replaced with smaller pebbles to maintain uniformity of the pebble tile. For vertical and contoured surfaces it is recommended to use a smaller pebble size and a polymer based adhesive with a quick drying time SEALING To protect the application and bring out the true color of the stone, it is recommended that the pebble tiles be sealed with a quality professional grade sealant following installation. We recommend using Dry Treat sealant, which is a non-yellowing sealant that will not deteriorate or break down over time. The porosity or water absorption in the pebbles varies, therefore staining may occur in areas subjected to water if tiles are left unsealed. CLEANING YOUR PEBBLE TILE The pebbles may be cleaned with a neutral mild detergent, a vinegar solution, or a 10% hydrochloric acid solution mixed with water. Apply with a stiff bristled brush and then rinse with water The pebbles and stones are a natural product, meaning that not two pieces are exactly alike. It is not unusual to find veins and lines of separation in the pebbles. This is generally a desired feature of the product. BEFORE YOU BEGIN Before installing the tiles, inspect your tiles for algae or yellow discoloration. This is the result of climate change and can easily be remedied by wetting the tiles and placing them outdoors in direct sunlight for eight hours. SUBSTRATES All substrates should be flat, clean, dry, free of any contamination, and firmly fixed in place. Deflections should be a maximum of 1/360 of the span for walls. Use in wet areas requires special attention involving appropriate substrates e.g.- concrete (cement boards) compressed sheet and treated plywood. Always use reinforced waterproof membranes. WATERPROOF MEMBRANES Waterproof membranes prevent the leakage of water through to framing and/or spaces behind. Attention must be paid to carrying the membrane up the wall, outside of shower boxes, installation of bond breakers, and sealing around penetrations. Membrane systems should be used in all areas. Some systems involve the use of a primer. ADHESIVE Use a product that is suitable for your project. We recommend using a latex-modified thin set to adhere the tiles. One product that is readily available is Vesabond by Custom Blend, an acrylic-based thinset that is a high-bond adhesive. Lay a 1 /4" layer of the adhesive and press the tile carefully into place. The adhesive should ooze through the mesh and contact the backside of the pebbles. It is important that each pebble be firmly imbedded in the adhesive. Use a product suitable for application with a 1 /4" notched trowel, and apply no more than three square feet of adhesive at a time. LAYING AND JOINT HIDING Before installation, inspect tiles to make sure all pebbles are properly in place on the tile. Remove and re-adhere any pebbles that may have been placed incorrectly. Interlocking pebble tiles are designed to create a seamless look. For maximum seamless effect, snip out any mesh sticking out between the interlocking joints or pebbles of the tiles where the interlock will be. Natural Stone Standing Pebble Guidelines For Installation It is a good idea to lay the tiles on the ground first to arrange desired alignment and layout before using adhesive. IT IS CRU- CIAL TO ALTERNATE AND STAGGER the pieces in each row so the seams do not line up from one row to the next. This will ensure that the seams do not show. The best way to do this is to start with the tile edge against the wall. In the next row above it, cut a piece in half to begin and then continue with full pieces. For the next row begin with a full piece etc.. Butt tiles together and do not leave the traditional 1 /4" to 3 /8" grout gap that is left for laying traditional ceramic tiles. If you are working with corners (such as in a shower), always start with the corner first and work your way out from there. You will need to order extra pieces from which you can pull pebbles to fill in gaps. For example, when a piece is flush against a wall, there will be a staggered or ragged piece. Simply pull pebbles off an extra piece, dab thinset onto the back of the loose pebble and press it into place in the needed areas between the tile and wall. GROUTING Grouting is optional for this product. For most applications, GROUT IS NOT USED in order to emphasize the natural appearance of the stone. SEALING To protect the application and bring out the true color of the stone, it is recommended that the pebble tiles be sealed with a quality professional grade sealant following installation. We recommend using Dry Treat sealant, which is a non-yellowing sealant that will not deteriorate or break down over time. The porosity or water absorption in the pebbles varies, therefore staining may occur in areas subjected to water if tiles are left unsealed. CLEANING YOUR PEBBLE TILE The pebbles may be cleaned with a neutral mild detergent, a vinegar solution, or a 10% hydrochloric acid solution mixed with water. Apply with a stiff bristled brush and then rinse with water
3 MA-103 Coverall Stone Inc. STACKED PEBBLE TILE th Ave. S. #209 Seattle, WA FAX Name: Stacked Pebble Tile Color: Stacked Mocha PT-ST-MA Size: 6 x 12 Mesh-backed Thicknes: 21mm+/- Weight: +/- 6 lbs. / sq. ft. Packing: Varies Use standard thin-set for installation. Buffet Remodel at Pizza Oven Stone to be sealed with clear matte sealer.
4 MA-104 Qortstone QUARTZ COUNTERTOP c/o Aurora Marble & Tile 6125 S. Valley View Blvd. Ste. F Las Vegas, NV Attn: Ed Gravelin (702) (702) Collection : Group A Assorted Series Color: QA1038 Pastel Beige Content: 93% Quartz, 7% Resin Available Size: 120 x 55 Thickness: 2cm 100% Green Buffet Remodel at Food Service Countertop
5 MA-105 Daltile STONE MOULDING 3755 W Sunset Ste D Las Vegas, NV Attn: David Payne fax david.payne@daltile.com Name: Travertine Accents Stone: T711 Torreon Finish: Honed Size: 1 W x 12 L Pencil Rail Buffet Remodel Trim Surround Custom Artisan Tile At Food Service Counter Only. OR PER BID
n o r s t o n e basalt interlocking tiles F i n e N a t u r a l S t o n e V e n e e r s
n o r s t o n e basalt interlocking tiles F i n e N a t u r a l S t o n e V e n e e r s TEL: 866 717 4548 EMAIL: SALES@NORSTONEUSA.COM WEB: WWW.NORSTONEUSA.COM norstone is a manufacturer and supplier of
More informationFLOORING INSTALLATION INSTRUCTIONS
FLOORING INSTALLATION INSTRUCTIONS This instruction manual defines the process to properly install RealStone Thin Veneer flooring based on standard stone installation practices. Like all construction processes
More informationStudent Services & Classroom Addition
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information1.3 Work shall include all reinforcement and accessories necessary to complete installation.
CERAMIC TILING GENERAL INFORMATION 1.1 Ceramic mosaic tile floors and bases, glazed wall tile wainscots and walls, and marble thresholds. 1.2 Installation will typically be with latex-portland cement mortar
More informationSECTION TILING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS
More informationHardscaping Installation Manual
Hardscaping Installation Manual INDEX Installation of Pavers... 1 Installation of Meshed Flagstone... 2 Installation of Veneer Stone... 3 Sand Set Installation of Pavers 1. Preparing the ground Mark your
More informationSECTION LATEX-MODIFIED MEDIUM BED MORTAR
SECTION 09305.24 LATEX-MODIFIED MEDIUM BED MORTAR This product guide specification can be used to specify Hydroment Big Tile & Stone Mortar, a latex-modified, medium bed mortar designed for setting large
More informationSECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION
SECTION 093000 - SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing, vapor retarder, and crack isolation in conjunction
More informationLAYOUT CONSIDERATIONS
1-800-447-2838 Installation Instructions Vanishing Lid System Layout Cover-Pools Vanishing Lid design is an adjustable, tray-support system for any kind or style of deck material you prefer to use for
More informationDuChâteau Concrete DeLuxe Wide-Plank Flooring Installation Instructions
DuChâteau Concrete DeLuxe Wide-Plank Flooring Installation Instructions DuChâteau Concrete DeLuxe Installation Guidelines are intended to offer general guidance as it relates to DuChâteau Concrete DeLuxe
More informationYARRABEE 360 GEOLOGY
Thank you for choosing our fine hand crafted GEOLOGY slate panels. For the best results, we believe that a contractor or professional wall covering installer with the correct tools should hang this material.
More informationSECTION STONE FLOORING
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 63 40 STONE FLOORING SPEC WRITER NOTE: Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and
More informationInstallation Guide Wall Panels
Installation Guide Wall Panels Jointless or Dry-Stacked Installation (Read Prior to installation) The MStone system is a jointless / dry-stacked installation where panels and corners fit tightly together
More informationSECTION UNIT PAVERS
PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.
More informationCTIOA REPORT
CERAMIC TILE INSTITUTE OF AMERICA, INC. 12061 Jefferson Blvd., Culver City, CA 90230-6219 CTIOA REPORT 2007-4-1 SUBJECT: STONE TILE By: CTIOA Specialty Tile Products Committee: Description Modular stone
More informationSTONE PRODUCT SPECIFICATION SANDSTONE. Some typical installation methods are: Pedestrian traffic only: reinforced concrete* 75mm thick
Please note these tips are guides only and should be used in addition to the relevant Australian Standards for trade practices. Note that installation may vary from site to site with varying conditions
More informationDivision 7-Moisture Protection Section 7-Under Tile Waterproofing Exceeds ANSI A Rev. 05/2012 Page 1
Page 1 Table of Contents General... 2 Approvals... 2 Applicator... 2 Product Delivery, Storage and Handling... 2 Limitations... 2 Safety... 2 Tools Needed for Application... 2 Products... 2 AVM System
More informationadjustable fusion shower pan surface mounted on subfloor installation guide
a a) Wall b) Tile c) Adjustable Shower Pan d) Liquid Membrane e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b d c f h g e adjustable fusion shower pan surface mounted on subfloor www.trendingaccessibility.com
More informationECO OUTDOOR INSTALLATION TIPS FLOORING COBBLESTONES
ECO OUTDOOR INSTALLATION TIPS FLOORING COBBLESTONES FLOORING WALLING FURNITURE WWW.ECOOUTDOORUSA.COM Installations Tips Please note these tips are guides only and should be used in addition to the relevant
More informationTriton DCI Decoupling Mat
1 Triton DCI Decoupling Mat Advanced Decoupling Mat with Superior Performance Lightweight waterproof underlayment Mortar Lock Mesh system for one pass mortar application, provides enhanced adhesion between
More informationCSI GUIDE Countertops
CSI GUIDE Countertops Part 1 General 1.0 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply
More informationRigid Core Installation & Maintenance Instructions
Rigid Core Installation & Maintenance Instructions Suitability Rigid Core Click Vinyl Flooring is completely waterproof floating floor and has got exceptional acoustic and insulation properties due to
More information8245 Remmet Ave Canoga Park, CA (888) Installation Instructions - AVM System 700 Under Tile Waterproofing and Anti-Fracture Membrane
8245 Remmet Ave Canoga Park, CA. 91304 (888) 414-1041 Division 7-Moisture Protection Page 1 Table of Contents General... 2 Approvals... 2 Applicator... 2 Product Delivery, Storage and Handling... 2 Limitations...
More informationGenesis Panel Systems LLC Dura-Max Brick Panel Siding Installation Instructions
Genesis Panel Systems LLC Dura-Max Brick Panel Siding Installation Instructions Thank you for purchasing the Genesis Dura-Max Brick Panel system for your project. The system allows you to have the look
More informationHYDRATHANE INTERIOR WATERPROOFING MEMBRANE. Product. Scope. Building Regulations. Appraisal No. 957 [2017] Appraisal No. 957 (2017) BRANZ Appraisals
HYDRATHANE INTERIOR WATERPROOFING MEMBRANE BRANZ Appraisals Technical Assessments of products for building and construction. Construction Chemicals NZ Ltd 16 Carpenter Road East Tamaki Auckland Phone (09)
More information1 PVC or ABS drain with strainer
Patents Pending ProBase II Single-Slope Shower Base and Kit CONTENTS 1. General Information...1 2. Materials...1 3. Planning...2 4. Preparation...3 5. Layout...3 6. Install Base and Shims...4 7. Install
More informationECO OUTDOOR INSTALLATION TIPS FLOORING SPLIT STONE
ECO OUTDOOR INSTALLATION TIPS FLOORING SPLIT STONE FLOORING WALLING FURNITURE WWW.ECOOUTDOORUSA.COM Installations Tips Please note these tips are guides only and should be used in addition to the relevant
More informationThin Architectural Splitface Block Veneer Specification Guide
Thin Architectural Splitface Veneer System with AccuTab Technology R Thin Architectural Splitface Block Veneer Specification Guide Section 04711: Manufactured Concrete Veneer Use this specification guide
More informationINDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES. Four-Side Interlock Loose Lay Installation
INDOOR RUBBER FLOORING INTERLOCKING INSTALLATION / MAINTENANCE GUIDELINES MARATHON SERIES Four-Side Interlock Loose Lay Installation The following pages are guidelines only... please read this manual thoroughly
More informationPOLYACRYLATE MODIFIED THINSET TERRAZZO 1
PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove
More informationSECTION CERAMIC TILE. B. Ceramic tile wall finishes including standard and custom designs.
SECTION 09 30 13 CERAMIC TILE PART 1 GENERAL 1.1 SECTION INCLUDES A. Ceramic tile floor and base finishes. B. Ceramic tile wall finishes including standard and custom designs. 1.2 REFERENCES A. ANSI/TCNA
More informationBush Elem. Addition & Alterations QUARRY TILE SECTION QUARRY TILE PART 1 - GENERAL
73651.01 QUARRY TILE 093016-1 1.1 RELATED DOCUMENTS: SECTION 093016 - QUARRY TILE PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES. Chapter 10
CONTENTS 10.1 PLASTERWORK 10.2 SECOND AND THIRD FIX FINISHES 283 Chapter 10 FUNCTIONAL REQUIREMENTS FUNCTIONAL REQUIREMENTS 10.1 PLASTERWORK Workmanship i. All workmanship must be within the tolerances
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationPLYWOOD FLOATING FLOOR
PLYWOOD FLOATING FLOOR Read First These suggestions represent generally accepted procedures for successful installation of Enka Building Products. These instructions may be followed, modified, or rejected
More informationIVC US. Light Commercial Installation Guide - Sheet Vinyl. Leading the Way
IVC US Light Commercial Installation Guide - Sheet Vinyl Leading the Way v. 5/2013 IVC US Light Commercial Installation Guide - Sheet Vinyl Flooring IVC US recommends the following guidelines for preparation
More informationCHAPTER 10: Finishes CONTENTS 10.1 PLASTERWORK ND AND 3 RD FIX FINISHES
CONTENTS 10.1 PLASTERWORK 10.2 2 ND AND 3 RD FIX FINISHES FUNCTIONAL REQUIREMENT 10.1 Plasterwork Workmanship Design Technical Manual TS-011-09-010412 i. All workmanship must be within defined tolerances
More informationFinish Flooring- Hard Flooring Materials
Finish Flooring- Hard Flooring Materials The most desirable types of flooring by designers and building owners Types of Hard Flooring Materials Concrete Stone Ceramic Tiles Quarry Tiles Bricks and Brick
More information***************************************************************************************************************
09330 QUARRY TILE *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number 09 30 16 ***************************************************************************************************************
More informationSingle Source Comprehensive Warranty. ARDEX Americas. Swimming Pool Guide
Single Source Comprehensive Warranty ARDEX Americas Swimming Pool Guide The ARDEX Pool System Wall Preparation WALLS SMOOTHING AND REPAIR ARDEX AM 100 TM Rapid Set Pre-Tile Smoothing and Ramping Mortar
More informationSECTION TILING
SECTION 093000 TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationEPOXY TERRAZZO 1 REV. 8/02
PART 1 - GENERAL GUIDE SPECIFICATIONS section 9400 EPOXY THINSET TERRAZZO (Without A Crack Suppression Membrane) REVISED MAY 2003 1.1 RELATED DOCUMENTS A. Section includes thin-set epoxy terrazzo flooring
More informationEditing notes to assist users are separated from specification text by rows of asterisks. Delete these notes prior to final printing.
SECTION 09635 LIMESTONE FLOORING This guide specification has been prepared by TexaStone Quarries LLC to assist design professionals in the preparation of a specification section covering cut limestone
More informationECO OUTDOOR INSTALLATION TIPS FLOORING PORPHYRY
ECO OUTDOOR INSTALLATION TIPS FLOORING PORPHYRY FLOORING WALLING FURNITURE WWW.ECOOUTDOORUSA.COM Installations Tips Please note these tips are guides only and should be used in addition to the relevant
More informationSemi Gloss Finishing Sealer
Natural Look Semi Gloss High Gloss Enhanced Enhancer Pro Sealer (Natural) Heavy duty water-based protection against tough oil and water-based stains. Enriches color Heavy duty protection against most stains
More informationLOOSE LAY INSTALLATION GUIDE PAGE 1 of 6
INSTALLATION GUIDE PAGE 1 of 6 MATERIALS REQUIRED FOR INSTALLATION: Tape Measurer Square Ruler Utility Knife 100lb Roller (if using adhesive) ACCEPTABLE SUBFLOORS: Happy Feet International will not warrant
More informationInstallation Instructions. Important. Recommended Tools. Palladium Rigid Sheet/Rubrail or Palladium G2 Sheet/Rubrail. Storage
Important Storage Flat sheet - Store Palladium Rigid Sheet in a clean, dry, interior area at temperatures between 50 F and 95 F [10-35 C]. Keep out of direct sunlight. Make sure sheet is well supported.
More informationXTREME-BOND INSTALLATION SYSTEM
XTREME-BOND FOR THIN-STONE VENEER Weather-resistant resistant Superior bonding & flexural strengths Exceptional sag resistance Meets requirements of Type S mortar Pre-blended for quality consistency from
More informationDAVCO K10 PLUS AND K10 RAPID WET AREA MEMBRANES. Product. Scope. Building Regulations. Appraisal No. 609 [2017]
DAVCO K10 PLUS AND K10 RAPID WET AREA MEMBRANES This Appraisal replaces BRANZ Appraisal No. 609 (2008) Amended 24 May 2018. BRANZ Appraisals Technical Assessments of products for building and construction.
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationTILING Lutheran Church of the Holy Spirit
SECTION 093000 - TILING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Porcelain tile. 2. Tile backing panels. 3. Metal edge strips. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationPART 1-SAWN THIN VENEER GENERAL
PART 1-SAWN THIN VENEER GENERAL WORK INCLUDED: All labor and material for the furnishing and installing of exterior or interior stone building veneer. RELATED WORK: Masonry Contractor shall include building
More informationJewel Stone. Decorative Concrete Overlay System. Part 1 GENERAL MANUFACTURER S SPECIFICATION
SEPTEMBER 2016 Jewel Stone Decorative Concrete Overlay System MANUFACTURER S IFICATION 09 62 81 Part 1 GENERAL 1.1 RELATED SECTIONS.1 Specification 03 30 00 Cast-in-Place Concrete.2 Specification 09 70
More informationAFM Anti-Fracture Membrane & AFM-WM Anti-Fracture Waterproofing Membrane Three-Part Specifications
AFM Anti-Fracture Membrane & AFM-WM Anti-Fracture Waterproofing Membrane Three-Part Specifications Protecto Wrap AFM Anti-Fracture Membrane and AFM - WM Anti-Fracture Waterproofing Membrane is a 40 mil
More informationUnderlayment Systems
Underlayment Systems Blanke Trims and Profiles for Ceramic Tile and Stone Blanke PERMAT /8" The Blanke PERMAT is an innovative uncoupling underlayment that offers all the labor saving benefits of the old
More informationFine Homebuilding. A tile floor that won t crack. 12 essential. Router bits. Choices for. Retaining walls. Adding an.
Fine Homebuilding TAUNTON S 7 HASSLE-FREE BEADBOARD WAINSCOT Fine Homebuilding AUGUST/SEPTEMBER 2005 A tile floor that won t crack Tiling a floor 2 essential router bits Beadboard wainscot Choices for
More informationSIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE. Product. Scope. Appraisal No. 811 [2013] Appraisal No. 811 (2013) Amended 28 August 2017
SIKALASTIC-152 EXTERIOR WATERPROOFING MEMBRANE Amended 28 August 2017 BRANZ Appraisals Technical Assessments of products for building and construction. Sika (NZ) Ltd PO Box 19 192 Avondale Auckland 1746
More informationPROTECTO DECK INSTALLATION INSTRUCTIONS
PROTECTO DECK INSTALLATION INSTRUCTIONS THE FOLLOWING MATERIALS ARE NEEDED TO COMPLETE THE PROTECTO DECK SYSTEM. Protecto Deck Protecto Deck is a cold applied, nominal 70 mil, self-adhering primary waterproofing
More informationAcceptable Floor Substrates: Concrete, cured mortar bed, plywood, and backer board.
SECTION 093000 - SHEET MEMBRANE WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing and vapor retarder, in conjunction with tile and dimension stone installations.
More informationfusion shower pan on wood joists installation guide
a a) Wall b) Tile c) Shower Pan d) Liquid waterproofing e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b c d f h g e fusion shower pan on wood joists installation guide www.trendingaccessibility.com
More informationNATURAL STONE CLADDING
CENTURY STONE NATURAL STONE CLADDING www.zclad.co.uk What is ZClad? Natural stone - made simple. ZClad is a cladding system made from natural stone. It creates a stylish veneer, whether building a contemporary
More informationPacific Polymers Elasto-Deck 5000MR Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide
More informationLOWLAND TRADING. installation reference
installation reference protection from weather It is essential to provide for all extremes of climate during the whole fixing operation and for as long as possible after grouting has been completed. Frost
More informationadjustable fusion shower pan on wood joists installation guide
a a) Wall b) Tile c) Shower Pan d) Liquid Membrane e) Crack Isolation Tape f) Cement Board g) Subfloor h) Joists b d c f h g e adjustable fusion shower pan on wood joists installation guide www.trendingaccessibility.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS Warranty... 2 Intro... 3 Laying Nuheat Membrane... 4 5 Laying the Tiles.... 6 Waterproofing... 7 Installing on Different Substrates Wood Structure... 8 9 Cement
More informationHYDRATHANE INTERIOR WATERPROOFING MEMBRANE. Product. Scope. Building Regulations. Appraisal No. 959 [2017] Appraisal No. 959 (2017) BRANZ Appraisals
Appraisal No. 959 [2017] HYDRATHANE INTERIOR WATERPROOFING MEMBRANE BRANZ Appraisals Technical Assessments of products for building and construction. Construction Chemicals Pty Ltd 49-57 Davis Street Wingfield
More informationSECTION SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING
SECTION 093000 - SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used for sound reduction, crack isolation
More informationOLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. RobinsonBrick.com
OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide RobinsonBrick.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines
More information1.6 QUALITY ASSURANCE A. Source Limitations for Tile: Obtain tile of each type and color or finish from one source or producer.
SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationECO OUTDOOR INSTALLATION TIPS FLOORING TORINO MELBOURNE SYDNEY BRISBANE ADELAIDE PERTH T ECOOUTDOOR.COM.AU
ECO OUTDOOR INSTALLATION TIPS FLOORING TORINO MELBOURNE SYDNEY BRISBANE ADELAIDE PERTH T. 1300 13 14 13 ECOOUTDOOR.COM.AU Installations Tips Please note these tips are guides only and should be used in
More informationCONCRETE STAIRS Note:
With the increased use of concrete tile and stone over the past decade, there has been an increase in demand for installing concrete tile or stone on stairs. Historically, these types of installations
More information1. PREPARATION 2. INSTALLATION 3. FINISHING 4. MAINTENANCE
In the following text vinyl floor(s) refers to floors from the Quick-Step Livyn Ambient Glue+ and Balance Glue+ collections. The branded accessories refer to the specific Quick-Step vinyl accessories.
More informationSTANDARD INSTALLATION GUIDELINES
GUIDELINES TOOLS MATERIALS SUBSTRATES PROCESSES TOOLS & MATERIALS PRIMARY INSTALLATION TOOLS NOTCHED EDGE TROWEL Suggested: 1/16 V Notch RUBBER FLOAT SPONGES RAZOR BLADES WATER BUCKETS PAINT BRUSH OR ROLLER
More informationSPECIFICATION FOR INSTALLATION OF WALKER ZANGER KAZA CONCRETE TILES ONTO VARIOUS SUBSTRATES
INSTALLATION INSTRUCTIONS SPECIFICATION FOR INSTALLATION OF WALKER ZANGER KAZA CONCRETE TILES ONTO VARIOUS SUBSTRATES QUALITY REQUIREMENTS All work to be carried out in accordance with TCNA (Tile Council
More informationLuxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call
Luxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call 702-534-1115 IMPORTANT Save time & avoid frustration! Read these entire instructions before starting your installation! Prior to
More informationInstallation instruction
TACKY TILE Installation instruction Introduction Tacky Tile has a Tacky technology backing that bonds firmly but not permanently to the subfloor, making installation easy, fast and clean. If at any time
More informationSECTION CERAMIC and QUARRY TILE
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 30 13 CERAMIC and QUARRY TILE A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 specification
More informationPacific Polymers Elasto-Deck 5000X2 Guide Specification
1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide
More informationSpecifications for Tile Backer Board wall and floor applications
Specifications for Tile Backer Board wall and floor applications Specifications for Tile Backer Board wall and floor applications Marmox Multiboard 600mm wide, 1250mm, 4, 6, 10, 12.5, 20, 30, 40, 50, 60mm
More informationSECTION SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING
SECTION 093000 - SHEET MEMBRANE SOUND REDUCTION, CRACK ISOLATION / JOINT BRIDGING, AND WATERPROOFING PART 1 - GENERAL This specification includes the sheet membrane used for sound reduction, crack isolation
More informationSECTION BRICK FLOORING
SECTION 09 63 13 BRICK FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brick flooring
More informationPERM-FLEX (JC) ASSEMBLY DIRECT APPLICATION TO CEMENT BOARD SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960
STUC-O-FLEX PERM-FLEX (JC) ASSEMBLY DIRECT APPLICATION TO CEMENT BOARD SUBSTRATES MANUFACTURERS SPECIFICATION / SECTION 09960 PART 1 - GENERAL 1.01 DESCRIPTION A. Provide all labor, materials and equipment
More informationoptimum glue Preparation INSTALLATION INFORMATION We recommend to order all panels for the same commercial flooring project at the same time.
Preparation We recommend to order all panels for the same commercial flooring project at the same time. Always store and transport your vinyl floor carefully to prevent distortions. Store and transport
More informationA. ASTM C190 - Test Method for Tensile Strength of Hydraulic Cement Mortars
SECTION 04850 (04 40 00) MSI PRECAST STONE VENEER SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. MSI Precast Stone Veneer for exterior and interior vertical surfaces. 1.2 RELATED SECTIONS Specifier Notes:
More informationMaster Specifications for Microcotta November 2017
SECTION 042130 - MICROCOTTA PART 1 - GENERAL 1.1 SUMMARY A. Provide Architectural Microcotta, cast architectural polymer resin units manufactured in accordance with the Contract Documents. 1.2 WORK INCLUDED
More informationWhen I started tiling, we didn t do our own shower pans that BATHS
BATHS Preventing Leaks in Tiled Showers Detail the pan properly before any tile is installed BY TOM MEEHAN Photos by Roe Osborn When I started tiling, we didn t do our own shower pans that job fell to
More informationStaron Interior Wall Fabrication
The information contained here is intended to provide the recommended cleaning method for water stains on the surface of Staron and Radianz installation. Substrate Substrate surface must be flat and free
More informationBRANZ Appraisal Certificate # 461 (2010) Internal wet areas.
SPECIFICATION FOR PROTECTO WRAP AFM-WM FOR INTERNAL WET AREAS BRANZ Appraisal Certificate # 461 (2010) Internal wet areas AFM/WM INTERNAL 0104 Page 1 AFM-WM INTERNAL SPECIFICATION PRODUCT DESCRIPTION Anti
More informationThermaSheet. multi-purpose insulated tile backer panels
ThermaSheet multi-purpose insulated tile backer panels A CODE PRODUCT DIMENSIONS RTTBB-06-1200 ThermaSheet Tile Backer Board 6mm 1200mm x 600mm RTTBB-10-1200 ThermaSheet Tile Backer Board 10mm 1200mm x
More informationFRONTIER20 WARNINGS AND RECOMMENDATIONS
FRONTIER20 WARNINGS AND RECOMMENDATIONS RAISED FLOORS INSTALLATION SYSTEM WARNINGS. Landmark products are made using the best technology available, and their technical performances match or exceed requirements
More informationCertainTeed. GlasRoc. Tile Backer
CertainTeed GlasRoc TM Diamondback GlasRoc Product Overview is a superior tile substrate for walls, ceilings, and countertops, specially designed by CertainTeed to meet the demands of highmoisture areas.
More informationL. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only*
L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only* Inspect the job site carefully before you begin the installation. Some conditions require specific installation
More informationECO OUTDOOR INSTALLATION TIPS FLOORING LIMESTONE MELBOURNE SYDNEY BRISBANE ADELAIDE PERTH T ECOOUTDOOR.COM.AU
ECO OUTDOOR INSTALLATION TIPS FLOORING LIMESTONE MELBOURNE SYDNEY BRISBANE ADELAIDE PERTH T. 1300 13 14 13 ECOOUTDOOR.COM.AU Installations Tips Please note these tips are guides only and should be used
More informationTABLE OF CONTENTS IMPORTANT INFORMATION. INSTALLATION GUIDELINES Revised 5/5/2017 REFERENCES...2
TABLE OF CONTENTS REFERENCES...2 PROJECT PLANNING...2 Verify Site Conditions...2 Building Code Requirements...2 Estimating Quantities Needed...2 SURFACE PREPARATION...3-5 Weather Resistive Barrier...3-4
More informationRapid-Set, Rapid-Dry, Super-Format Tile and Uncoupling Membrane Mortar
ARDEX S 28TM MICROTEC Rapid-Set, Rapid-Dry, Super-Format Tile and Uncoupling Membrane Mortar Unmatched performance and protection for super-format tile and uncoupling membrane installations! Rapid-drying
More informationApplication Instructions for Keystone Kool Deck on Existing Concrete
Application Instructions for Keystone Kool Deck on Existing Concrete REQUIRED MATERIALS Keystone Kool Deck PTA Bonding Agent Water 20 Mesh Marble Sand White Portland Cement OPTIONAL TOOLS Mortex Pattern
More informationSpec Master 5/7/ For each product requiring color and texture selection, provide full size samples.
SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationCARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS
CARLISLE DECK COATING INSTALLATION OVER EXISTING POLYURETHANE COATINGS 1. GENERAL A. When coating over existing coatings, Carlisle can not assume responsibility for the adhesion of the existing coating,
More informationSECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.
(Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications
More informationB. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.
SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information