SPECIFICATIONS: Architectural

Size: px
Start display at page:

Download "SPECIFICATIONS: Architectural"

Transcription

1 May 15, 2014 Aedis Architects 387 S. First St. San Jose, CA Subject: Restroom Flooring Replacement at Various Sites New Haven Unified School District Project No. DSA File No. [n/a] DSA Application No. [n/a] ADDENDUM NO. 1 CHANGES AND/OR CLARIFICATIONS OF THE DRAWINGS AND SPECIFICATIONS ARE AS FOLLOWS: SPECIFICATIONS: Architectural ITEM NO. 1.1: : POLYACRYLATE COMPOSITION UNDERLAYMENT Delete: Section Polyacrylate Composition Underlayment in its entirety. Information has been moved to section Fluid-Applied Flooring. ITEM NO. 1.2: : FLUID-APPLIED FLOORING Replace: Section Fluid-Applied Flooring in its entirety with the attached.

2 ADDENDUM NO. 1 RESTROOM FLOORING REPLACEMENT AT VARIOUS SITES New Haven Unified School District Project No. 5/15/14 Page 2 of 2 DSA File No. [n/a] DSA Application No. [n/a] Thang Do, Architect AEDIS Architecture & Planning Attachments: Cover Sheet Fluid-Applied Flooring 2

3 SECTION FLUID-APPLIED FLOORING THIS SECTION MODIFIED AS PART OF ADDENDUM 1 PART 1 GENERAL 1.01 SECTION INCLUDES Restroom Flooring Replacement at Various Sites A. Fluid-applied epoxy flooring and base, with 10-pound vapor control primer. B. Fluid-applied urethane-cement flooring and base. C. Polyacrylate composition underlayment for fill and/or creating slope for drainage RELATED REQUIREMENTS A. The General Conditions, Supplementary Conditions and Division 1 General Requirements are hereby made a part of this Section as fully as if repeated herein SUBMITTALS A. See Section Administrative Requirements, for submittal procedures. B. Product Data: Provide manufacturer's data on specified products, describing physical and performance characteristics; sizes, patterns and colors available. C. Samples: Submit two samples, 2-1/2 x 4 inch ( x mm) in size illustrating color, pattern, and texture for each floor material for each color specified. Provide non-slip texture. D. Samples for Verification: For each resinous flooring system or color specified, provide 2 each, 6 inches (150mm) square samples in the selected color and texture, applied to a ridged backing by the installing contractor for this project E. Manufacturer's Installation Instructions: Indicate special procedures. F. Maintenance Data: Include maintenance procedures, recommended maintenance materials, procedures for stain removal, repairing surface, and suggested schedule for cleaning. (Project Close-Out Item) G. Material certificates signed by manufacturer certifying that each flooring system complies with requirements specified herein. H. Applicator s Certification: submit letter from manufacturer stating that the applicator is authorized to offer a joint applicator/manufacturer labor and material warranty for the work performed on this specific project. 1. Reference jobs: Provide names and contact information for at least 3 projects similar to this project and using the specified system or the proposed equivalent system that are over 5 years old and were installed by this Installing Contracting Company with the crew who will install this project. Reference installations must be within 25 miles of this project. I. Antimicrobial System: EPA licensing documentation and permitting for Antimicrobial System as well as manufacturer s documentation showing the antimicrobial has long-term service life in the cured epoxy and is not an in-can preservative. J. Warranty: Submit written letter from Manufacturer offering joint applicator/manufacturer labor/material warranty for this specific project and with this particular subcontractor-installer. K. Vapor Control System: Submit Manufacturer s technical data for vapor control system. System must be manufactured by the manufacturer of the epoxy mosaic composition flooring product (NO EXCEPTIONS) and be engineered to prevent debonding resulting from vapor emissions up to 10 lbs when tested in accordance with ASTM F-1869 or Alkalinity levels up to 14. L. Submit Manufacturer s technical data for semirigid polymeric joint/crack stripping/waterproofing and antifracture material that that is to be used in conjunction with vapor control system. Rigid or fiberglass-reinforced materials are not acceptable. M. Polyacrylate Underlayment: Submit Manufacturer s technical data for polyacrylate underlayment. Product must be made by the primary materials manufacturer and compatible with the flooring systems specified, and must reach a minimum strength of 2,200 psi. FLUID-APPLIED FLOORING

4 1.04 QUALITY ASSURANCE A. Single-Source Responsibility: Obtain flooring materials, including primers, resins, hardening agents, colored aggregates and finish or sealing coats, from a single manufacturer (NO EXCEPTIONS). B. Manufacturer Qualifications: Company specializing in manufacturing products specified in this section with minimum three years documented experience. C. Qualified Materials: Request for material approvals for any products other than the specified product must be submitted to the architect two weeks prior to the bid, including complete application specification and physical characteristics. Any request after this date will not be accepted. Failure of performance requires immediate removal and replacement of unapproved substituted material with those originally specified at no cost to the owner, Architect, construction manager, or general contractor. D. Installer Qualifications: Engage an experienced contracting company who has specialized in installing the specified resinous flooring system required for this Project and who offers reference projects as per part 1.03.H.1 of this specification and who is authorized to offer a joint labor and material warranty with manufacturer of primary materials. 1. Installers who have submitted and obtained approval for alternate equivalents to the basis of design product shall have installed the approved alternate for over 5 years and shall provide references and manufacturer s joint warranty letter in compliance with items 1.03.H and J DELIVERY, STORAGE, AND HANDLING A. Deliver materials in original packages and containers with seals unbroken and bearing manufacturer's labels containing brand name and directions for storage and mixing with other components. B. Store materials to comply with manufacturer's directions to prevent deterioration from moisture, heat, cold, direct sunlight, or other detrimental effects. C. Store resin materials in a dry, secure area. D. Store materials for three days prior to installation in area of installation to achieve temperature stability FIELD CONDITIONS A. Environmental Conditions: Comply with epoxy-flooring manufacturer's directions for maintenance of ambient and substrate temperature, moisture, humidity, ventilation, and other conditions required to execute and protect work. B. Lighting: Permanent lighting will be in place and working before installing resinous flooring. C. HVAC: HVAC shall be in full operation during installation and cure period of Resinous flooring. General Contractor shall ensure that the floor temperature remains above 60F at all times. PART 2 PRODUCTS 2.01 MANUFACTURERS A. Fluid-Applied Flooring: 1. Crossfield Products Corp: a. Contact Richard V. Swan & Associates for acceptable applicators and other information: (650) Substitutions: See Section Product Requirements. a. Only clear silica aggregate troweled floors with mosaic highlights shall be acceptable. b. Colored quartz, limestone varieties and other aggregates with moh hardness less than 7 are not acceptable. c. Broadcast or quartz floors (including ceramic floors) or any other form of color-coated sand aggregates will not be accepted. FLUID-APPLIED FLOORING

5 2.02 FLOORING SYSTEM SCHEDULE A. Epoxy Flooring System 1. Toweled epoxy mosaic composition flooring with embedded non-slip aggregate. 2. Thickness: 1/4" nominal when dry. 3. Color: 315 Desert Beige 4. Location: where indicated in the drawings. 5. Top Coat: anti-slip polyurethane, with EPA-licensed antimicrobial/antibacterial system. 6. Underlayment: Polyacrylate underlayment. Provide as required to create slope for drainage and where metal lath is indicated to be installed. 7. Metal Lath: provide metal lath over all plywood and wood substrates. 8. Vapor Control Primer: for use where required by field conditions, see section 3.01.D below. 9. Waterproofing/Antifracture membrane: installed directly below the epoxy mortar layer. Waterproofing/Antifracture Membrane is required only on upper floors or over underlayment used over wood substrates. B. Urethane-Cement Flooring System 1. Urethane-cement flooring with embedded non-slip aggregate. 2. Thickness: 1/4" nominal when dry. 3. Color: 315 Desert Beige 4. Location: where indicated in the drawings 5. Top coat: anti-slip novolac 2.03 MATERIALS A. Epoxy Mosaic Mortar 1. Product: Dex-O-Tex Cheminert Terracolor 2. Physical Properties: a. Thickness: 1/4" b. Compressive Strength (ASTM C 579): 10,000 psi. c. Tensile Strength (ASTM C 307): 1395 psi. d. Flexural Strength (ASTM C 580): 4,300 psi. e. Surface Hardness (ASTM D-2240): Durometer "D" 81 f. Abrasion Resistance (ASTM D 1044 ): 0.0 gr. loss g. Indentation (MIL-D-3134): >1.0 % h. Impact Resistance (Gardner Impact Tester): No chipping, cracking, or delamination and not more than0.014" indentation i. Adhesion (A.C.I. Comm. No ): >400 psi (100% failure in concrete) j. Electrical Conductivity (NFPA 56A): Di-electric k. Flammability (ASTM E-648/NFPA 253/FTMS 372): Greater than 1.07 watts/cm2 B. Non-slip aggregate: Dex-O-Tex Synthetic Aggregate C. Urethane-Cement Flooring 1. Product: Tek-Crete SL 2. Integral Coved Base: Tek-Crete VRT D. Textured Epoxy Top Coat (Epoxy Flooring System) 1. Type recommended or produced by manufacturer of epoxy resin mosaic flooring system for type and profile of desired final finish. 2. Product: Decorflor epoxy E. Textured Novolac Top Coat (Urethane-Cement Flooring System) 1. Type recommended or produced by manufacturer of urethane-cement flooring system for type and profile of desired final finish. 2. Product: Posi-Tred CR F. Polyacrylate Cement Underlayment 1. Product: Dex-O-Tex A-81 Underlayment 2. Physical Properties: FLUID-APPLIED FLOORING

6 a. Compressive Strength ASTM C109: 24 hrs: 5000 psi 72 hrs: 6140 psi b. Tensile Strength ASTM C307: 800 psi c. Flexural Strength ASTM C580: 1,200 psi d. Weight: 130 pounds/ft³ e. Hardness ASTM D2240, Shore D: f. Adhesion ASTM D4541: >400 psi (100% failure in concrete) g. Indention MIL-D-3134, Para : 2.26% (Steadily Applied Load, 2,000 lbs. On 1 steel ram imposed for 30 min.) h. Water Absorption MIL-D-3134: 3.14% i. Flammability: Non-combustible j. Impact Resistance (Gardner Impact Tester): No chipping, cracking, or delamination more than G. Crack/Joint Sealant and Waterproofing/Antifracture Membrane 1. Product: Dex-O-Tex SC Membrane 2. Physical Properties: a. Tensile Strength (ASTM D 638): 1,500 psi b. Tensile Elongation (ASTM D 638): 17,150 psi, 96% elongation to break c. Tear Strength (ASTM D 638): 120 lb./in. d. Hardness (ASTM D2240, shore D): e. Compressive (ASTM ASTM D695): 4,000 psi f. Water Absorption (ASTM D570): <0.2% g. Flammability (ASTM D635): Self-extinguishing over concrete h. Microbial Resistance (ASTM G21) Passes 2.04 ACCESSORIES A. Vapor Control Membrane: 10-pound vapor control primer recommended by the primary materials manufacturer. 1. Product: Vapor Control Primer 200 by Dex-O-Tex. 2. Physical Properties: Provide negative side vapor emissions system that meets or exceeds the listed minimum physical property requirements when tested according to the referenced standard test method. a. Adhesion ASTM D4541 >400 psi (100% failure in concrete) b. Adhesion ASTM D4541 >400 psi (100% failure in concrete, with Moisture Vapor Emission Rate at 10 lbs/1000 sf/24 hours per ASTM F1869) c. Compressive Strength ASTM D695 21,000 psi d. Tensile Strength ASTM D psi e. Tensile Elongation ASTM D % f. Permeability Rating ASTM E96 Dry <0.18.Wet <0.80 g. Microbial Resistance ASTM G21 Passes h. Alkali Resistance ASTM D1308 Resistant B. Antimicrobial Additive: Incorporate EPA-licensed antimicrobial chemical additive to prevent growth of most bacteria, fungi, algae and actinomycetes. 1. Product: Dexcide Antimicrobial/Antibacterial System C. Expanded wire lath: 3.4# galvanized diamond metal lathing filled with a minimum of ¼ polyacrylate underlayment. Additional underlayment may be installed to create slope for drainage. PART 3 EXECUTION 3.01 EXAMINATION A. Verify that sub-floor surfaces are smooth and flat within the tolerances specified for that type of work and are ready to receive flooring. B. Verify that wall surfaces are smooth and flat within the tolerances specified for that type of work, are dust-free, and are ready to receive flooring. FLUID-APPLIED FLOORING

7 C. Verify that sub-floor surfaces are dust-free and free of substances that could impair bonding of materials to sub-floor surfaces. D. Verify that concrete sub-floor surfaces are ready for flooring installation by testing for moisture emission rate and alkalinity in conformance with ASTM F 1869 and ASTM F 2170; obtain instructions if test results are not within limits recommended by flooring materials manufacturer. If emissions exceed 10 lbs notify Architect for instructions to install vapor control system. E. Verify that required floor-mounted utilities are in correct location. F. Notify the Architect of conditions detrimental to the proper and timely completion of the work. Do not proceed with the work until unsatisfactory conditions have been corrected by the Contractor in conformance with the Contract Document PREPARATION A. Substrate: Perform preparation and cleaning procedures according to flooring manufacturer's instructions for particular substrate conditions involved, and as specified. Provide clean, dry and neutral substrate for flooring application. B. Concrete Surfaces: Shot-blast or grind as required to obtain optimum bond of flooring to concrete. Remove sufficient material to provide a sound surface free of laitance, glaze, efflorescence, and any bond-inhibiting curing compounds or form release agents. Remove grease, oil, and other penetrating contaminates. Repair damaged and deteriorated concrete to acceptable conditions. Leave surface free of dust, dirt, laitance, and efflorescence. C. Plywood Surfaces: General Contractor must remove damaged and deteriorated plywood and replace with new. Verify plywood surface is flush and level throughout. Remove laitance, grease, and foreign matter. Install expanded wire lath over all wood surfaces to receive underlayment. D. Vapor Control Membrane: Allow slab to cure the minimum prescribed time as required by the manufacturer. Install vapor control membrane and resurfacer in accordance with the manufacturer's written instructions. E. Materials: Mix resin hardener, antimicrobial, and aggregate when required, and prepare materials according to flooring system manufacturer's instructions INSTALLATION - FLOORING A. Apply in accordance with manufacturer's instructions. B. Apply each coat to minimum thickness indicated. C. Polyacrylate underlayment: install where necessary for fill or to create positive slope for drainage. 1. Install in accordance with manufacturer's instructions. 2. Bond Coat: Apply bondcoat/primer over prepared substrate at manufacturer's recommended spreading rate. 3. Body Coat: Over fresh bondcoat/ primer, trowel apply polyacrylate mortar mix at nominal thickness as specified; hand or power trowel. When cured, sand or grind if necessary to remove trowel marks or roughness. D. Bond Coat: Apply bond coat over prepared substrate at manufacturer's recommended spreading rate. Primer is not required for urethane-cement flooring. E. Body Coat; Over primer, trowel apply mortar mix at nominal 1/4-inch Thickness; hand or power trowel. Allow to cure before proceeding. F. Finish or Sealing Coats: After body coat has cured sufficiently, apply grout and finish coats of type recommended by flooring manufacturer to produce finish matching approved sample and in number of coats and spreading rates recommended by manufacturer. 1. Final finish coat shall be In color and skid retardant profile as approved by Architect. 2. Finished floor shall be 1/4-inch thick, uniform in color and free of trowel marks. G. Finish to smooth level surface. FLUID-APPLIED FLOORING

8 H. Cove Base: Apply cove base mix to wall surfaces at locations shown to form cove base height of 6-inches in a seamless manner forming a minimum 3/8 inch radius cove as an integral unit unless otherwise indicated. Follow manufacturer's printed instructions and details including taping, mixing, priming, troweling, sanding, and top-coating of cove base. I. Floor drains: 1. Drain flange shall be finished flush with substrate. 2. Allow one-eighth (1/8) inch per foot slope in the flooring substrate to drain. 3. Care must be taken to provide adequate elevation at thresholds to provide proper slope to drain PROTECTION A. Cure epoxy mosaic composition and urethane-cement flooring materials according to manufacturer's directions, taking care to prevent contamination during application stages and before completing curing process. Close application area for a minimum of 24 hours. Note full chemical/stain resistance of epoxies is not achieved for 7 days. General Contractor to protect from cleaning and spills for 7 days. B. Prohibit traffic on floor finish for 24 hours after installation. 1. Barricade area to protect flooring until cured. C. Protect finished floor with rosin paper. Additionally, use masonite, if rolling load traffic exists. D. Protect from cleaning and spills for 7 days. E. Clean with manufacturer recommended cleaner. END OF SECTION FLUID-APPLIED FLOORING

SECTION EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor

SECTION EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor SECTION 09720 EPOXY MOSAIC COMPOSITION FLOORING Dex-O-Tex Cheminert Terracolor PART 1.00 - GENERAL 1.01 GENERAL REQUIREMENTS A. Work of this Section, as shown or specified, shall be in accordance with

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroCrete RT Rake/Trowel Urethane Mortar 3/16-1/4 (4.5-6.0 mm) Floor Resurfacing System Part 1: General 1.01 System Description A. System I Skid-Resistant Finish Resurfacing

More information

RESINOUS FLOORING

RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS Bid #2017-17 A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this

More information

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Part 1: General Architectural Specification FloroCrete SLX Self-Leveling Urethane Mortar w/broadcast nominal 3/16 Flooring System 1.01 System Description A. Squeegee/Troweled-applied, aggregate-rich polyurethane

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification -- FloroCryl Shop MMA (Methyl Methacrylate) - Silica Sand Single Broadcast 1/16 (1.59 mm) Flooring System Part 1: General 1.01 System Description A. Roller-applied penetrating

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Part 1: General Florock Seamless Flooring Systems Architectural Specification FloroQuartz BC Epoxy - Colored Quartz 1/8 (0.125 mm) Double Broadcast Flooring System 1.01 System Description A. Roller-applied

More information

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING

SECTION RESINOUS FLOORING or SECTION QUARTZ FLOORING SECTION 09 67 23 RESINOUS FLOORING or SECTION 09 67 26 QUARTZ FLOORING PART 1 - GENERAL 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) A. Provide all labor, materials,

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroBuild XT Extreme Impact & Abrasion Resistant Resurfacing System Part 1: General 1.01 System Description A. Roller applied 100% solids epoxy primer, followed by an extreme

More information

SECTION EPOXY TERRAZZO

SECTION EPOXY TERRAZZO SECTION 09402 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to

More information

A. This Section includes resinous flooring systems with epoxy body coat(s).

A. This Section includes resinous flooring systems with epoxy body coat(s). SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes resinous flooring systems with epoxy body coat(s). 1. Application Method: Troweled (Slurry, Seeded or Broadcast

More information

1/16 Single Broadcast Polymer Flooring System

1/16 Single Broadcast Polymer Flooring System specification 1/16 Single Broadcast Polymer Flooring System Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions

More information

Section SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS

Section SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS SECTION 096723 - RESINOUS FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification FloroBuild PT/ HT Epoxy Mortar ¼ Power Trowel or Hand Trowel Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer

More information

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.

More information

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE

SECTION EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE PART 1 GENERAL 1.01 SUMMARY SECTION 09730 EPOXY RESIN FLOORING WITH INTEGRAL COVE BASE A. Related Sections: 1. 03300 - Cast-in-Place Concrete. 2. 09000 - Patching and Finishes. 3. 09900 - Painting. 4.

More information

SECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES

SECTION SUBSURFACE PREPARATION FOR FLOOR FINISHES PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 05 16 SUBSURFACE PREPARATION FOR FLOOR FINISHES SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. Also delete any other item or paragraph

More information

1.2 SUMMERY A. Section Includes: 1. High-Performance Polyurethane Resinous flooring systems. 2. Decorative Polyurethane Resinous flooring systems.

1.2 SUMMERY A. Section Includes: 1. High-Performance Polyurethane Resinous flooring systems. 2. Decorative Polyurethane Resinous flooring systems. PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and supplementary Conditions and Division 01 Specification Sections apply to this Section. 1.2

More information

1/4 Industrial Trowel System

1/4 Industrial Trowel System System Specification 1/4 Industrial Trowel System Revision Date: 6/2015 Printed Date: 6/2015 PART 1 GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of contract including General and Special

More information

Union County Vocational - Technical Schools Scotch Plains, New Jersey

Union County Vocational - Technical Schools Scotch Plains, New Jersey SECTION 096623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

FLEXMAR 3-Coat High-Build Colored Quartz System

FLEXMAR 3-Coat High-Build Colored Quartz System Guide Specification SECTION 09 67 23: HIGH-PERFORMANCE RESINOUS FLOORING FLEXMAR 3-Coat High-Build Colored Quartz System 20-27 mils DFT This guide specification is intended to assist the specifier in developing

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification -- FloroCryl Deck- 1/8 (125 mil) MMA (Methyl Methacrylate) Waterproofing 1/8 Flooring System Part 1: General 1.01 System Description A. Roller-applied penetrating MMA primer

More information

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building

May 8, 2017 ADDENDUM #1. IFB Resin Floor System For Highway Department Central District Building May 8, 2017 ADDENDUM #1 IFB 17-082 Resin Floor System For Highway Department Central District Building Addendum #1 is being issued to offer an alternate resin flooring system. 096700 FLUID-APPLIED FLOORING

More information

Section Pedestrian Traffic Coatings

Section Pedestrian Traffic Coatings Guide Specification MiraFlex II - For Concrete Surfaces Pedestrian Deck and Waterproofing System (Specification writer shall choose the most appropriate section that applies to a given scope of work, including

More information

SECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM

SECTION RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM SECTION 096723 RESINOUS FLOORING PLEXIQUARTZ BROADCAST SKID-RESISTANT QUARTZ SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. This section includes the following: 1. Seamless epoxy flooring system, 1/16 th, 3/32

More information

Desco Quartz Cremona Specifications

Desco Quartz Cremona Specifications Desco Quartz Cremona Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply

More information

SECTION RESINOUS FLOORING

SECTION RESINOUS FLOORING SECTION 09705 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work of this Section includes all materials and installation necessary to provide resinous flooring system with integral cove base and top finish

More information

Desco Granite Flooring Specifications

Desco Granite Flooring Specifications Desco Granite Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply

More information

POLYACRYLATE MODIFIED THINSET TERRAZZO 1

POLYACRYLATE MODIFIED THINSET TERRAZZO 1 PART 1 - GENERAL GUIDE SPECIFICATION POLYACRYLATE MODIFIED THINSET TERRAZZO - REVISED AUG 02 1.1 RELATED DOCUMENTS A. Section includes thin set Polyacrylate Modified Terrazzo flooring (and integral cove

More information

DECOCOLOR FLOORING SYSTEM

DECOCOLOR FLOORING SYSTEM AIA Specification DECOCOLOR FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions of the

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating pigmented epoxy primer, decorative pigmented

More information

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS

SECTION MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS SECTION 09699 MOISTURE RESISTANT/WATER-PROOF FLOORING ADHESIVE FOR CONCRETE SLABS PART 1 GENERAL 1.1 SECTION INCLUDES A. Testing and application of systems for the reduction of moisture resistant or water-proof

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification Florotallic Epoxy and Urethane Flooring System Part 1: General 1.01 System Description A. Roller-applied 100% solids, penetrating epoxy primer, decorative pigmented epoxy coatings

More information

Broadcast Parking Garage System

Broadcast Parking Garage System AIA Specification Part 1 General Broadcast Parking Garage System 1.01 Work Included A. All work to be provided in this section shall include material, labor, and equipment necessary to furnish the complete

More information

1/8 DECORATIVE BROADCAST FLOORING SYSTEM

1/8 DECORATIVE BROADCAST FLOORING SYSTEM AIA specification AIA specification AIA Specification 1/8 DECORATIVE BROADCAST FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or

More information

SECTION RESINOUS FLOORING

SECTION RESINOUS FLOORING PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 67 23 1. Use this section only for NCA projects. 2. Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the

More information

Florock Seamless Flooring Systems

Florock Seamless Flooring Systems Architectural Specification Floropoxy/Florospartic 5 Self-Leveling Epoxy/Polyaspartic Flooring System Part 1: General 1.01 System Description A. Roller applied 100% solids, penetrating pigmented epoxy

More information

BROADCAST KITCHEN FLOORING SYSTEM

BROADCAST KITCHEN FLOORING SYSTEM AIA specification AIA specification AIA Specification Part 1 - GENERAL BROADCAST KITCHEN FLOORING SYSTEM General Provisions A. Work to be covered by this section, under written specification or by drawing,

More information

Pacific Polymers Elasto-Deck 5000X2 Guide Specification

Pacific Polymers Elasto-Deck 5000X2 Guide Specification 1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000X2 OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000X2 Guide

More information

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings.

A. Section includes hydraulic-cement-based, polymer-modified, self-leveling underlayment for application below interior floor coverings. SECTION 03 54 16 - HYDRAULIC CEMENT UNDERLAYMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01

More information

EPOXY TERRAZZO 1 REV. 8/02

EPOXY TERRAZZO 1 REV. 8/02 PART 1 - GENERAL GUIDE SPECIFICATIONS section 9400 EPOXY THINSET TERRAZZO (Without A Crack Suppression Membrane) REVISED MAY 2003 1.1 RELATED DOCUMENTS A. Section includes thin-set epoxy terrazzo flooring

More information

A. Coordinate seamless quartz flooring and base with work before and after. See especially:

A. Coordinate seamless quartz flooring and base with work before and after. See especially: 09673 SEAMLESS QUARTZ FLOORING AND BASE SPECIFIER: This section covers seamless quartz flooring for various sorts of areas and functions (which may include stair treads and landings) in typical thicknesses,

More information

Pacific Polymers Elasto-Deck 5000MR Guide Specification

Pacific Polymers Elasto-Deck 5000MR Guide Specification 1 071813-1 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide Specification SECTION 071813 TRAFFIC COATINGS ELASTO-DECK 5000MR OVER CONCRETE 2 071813-2 July 2018 Pacific Polymers Elasto-Deck 5000MR Guide

More information

Advantages: Advantages include:

Advantages: Advantages include: Elgin, Illinois Hi-Tek Polymers Floor Description: Hi-Tek Polymers Floor is a decorative thin-set epoxy system of 1/4" (6,3mm) to 3/8 (MM) which meets all the standards set by the NTMA (National Terrazzo

More information

SECTION Pedestrian Traffic Coatings{PRIVATE } 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary)

SECTION Pedestrian Traffic Coatings{PRIVATE } 1.1 SUMMARY (Specification writer shall add, delete or amend, as deemed necessary) Guide Specification MiraFlex II For Plywood Decks Pedestrian Deck and Waterproofing System (Specification writer shall choose the most appropriate section that applies to a given scope of work, including

More information

DUR-A-FLEX, Inc. Page 1 of 5

DUR-A-FLEX, Inc. Page 1 of 5 DUR-A-FLEX, Inc. Page 1 of 5 SECTION 09 67 23-RESINOUS FLOORING DUR-A-GARD EPOXY COATING WITH URETHANE (Armor Top) TOPCOAT (23 mils) Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general

More information

SECTION RESINOUS FLOORING

SECTION RESINOUS FLOORING SECTION 096723 - RESINOUS FLOORING PART I GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,

More information

MRXL4 CR6 Surface Requirements: XNS, NS, M, S; Special Requirements: NO PART 1 : GENERAL

MRXL4 CR6 Surface Requirements: XNS, NS, M, S; Special Requirements: NO PART 1 : GENERAL PART 1 : GENERAL 1.01 DESCRIPTION A. WORK INCLUDED: All labor, materials, appliances, tools, equipment, facilities, transportation and services necessary for and incidental to performing all operations

More information

DECOFLAKE DECORATIVE FLOORING SYSTEM

DECOFLAKE DECORATIVE FLOORING SYSTEM AIA Specification DECOFLAKE DECORATIVE FLOORING SYSTEM Part 1 - GENERAL General Provisions A. Work to be covered by this section, under written specification or by drawing, shall comply with all provisions

More information

SECTION ELASTOMERIC LIQUID FLOORING

SECTION ELASTOMERIC LIQUID FLOORING SECTION 096713 - ELASTOMERIC LIQUID FLOORING PART I GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification

More information

3/16-1/4 Urethane Concrete Slurry System

3/16-1/4 Urethane Concrete Slurry System 3/16-1/4 Urethane Concrete Slurry System PART 1 GENERAL 1.01 RELATED DOCUMENTS Drawings and general provisions of contract including General and Special Conditions and Division I, excepting special Submittal

More information

KOSTER AMERICAN CORPORATION

KOSTER AMERICAN CORPORATION Section 09699 PART 1 GENERAL Water Vapor Emission Control Systems 1.1 RELATED DOCUMENTS A. Drawings, documents, and general provisions of the Contract, including, but not necessarily limited to, General

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy-Shell 1000 Color System GUIDE SPECIFICATION SECTION 09725 PART 1

More information

Engine Bay Floors Floor Resurfacing 4000

Engine Bay Floors Floor Resurfacing 4000 Engine Bay Floors Floor Resurfacing 4000 P.O. Box 341 Macungie, PA 18062 610.530.7710 800.573.9198 www.enginebayfloors.com 1.1 SUBMITTALS Flooring Specification SECTION 1 GENERAL A. Product Data: Submit

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Products SECTION 09 05 61.13 MOISTURE VAPOR EMISSION CONTROL PART 1 - GENERAL 1.1 RELATED DOCUMENTS

More information

SECTION CONCRETE TOPPING or SECTION DECORATIVE FINISHING or SECTION CEMENTITIOUS COATINGS

SECTION CONCRETE TOPPING or SECTION DECORATIVE FINISHING or SECTION CEMENTITIOUS COATINGS CSI Master Format does not currently include a specific section number for Cementitious Microtopping Flooring systems. Specification writer shall choose the most appropriate section that applies to the

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Color System GUIDE SPECIFICATION SECTION 09725 PART 1

More information

B. Following all applicable manufacturer s guidelines and application instructions shall be considered a requirement of this specification.

B. Following all applicable manufacturer s guidelines and application instructions shall be considered a requirement of this specification. Guide Specification Miracote MPC (Multipurpose Protective Coating) Cementitious Microtopping System (Specification writer shall choose the most appropriate section that applies to a given scope of wk,

More information

Custom Polishing Systems

Custom Polishing Systems Custom Polishing Systems VitraFlor by Bomanite Guideline Specification Standard Application PART 1 GENERAL SECTION 033000 CAST-IN-PLACE CONCRETE 1.1 RELATED DOCUMENTS A. Drawings and general provisions

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Single Quartz Broadcast System GUIDE SPECIFICATION SECTION

More information

Tennant Company October North Lilac Drive Minneapolis, Minnesota Guide Specification

Tennant Company October North Lilac Drive Minneapolis, Minnesota Guide Specification October 2016 701 North Lilac Drive Minneapolis, Minnesota 55422 800-553-8033 www.tennantco.com info@tennantco.com Guide Specification SECTION09 67 23 RESINOUS FLOORING (Tennant Epoxy Flake SR-HTS) PART

More information

(Specification writer shall choose the most appropriate section that applies to a given scope of work) SECTION Painting and Coating

(Specification writer shall choose the most appropriate section that applies to a given scope of work) SECTION Painting and Coating Guide Specification Miracote Mirastain Architectural Staining System (Specification writer shall choose the most appropriate section that applies to a given scope of work) PART 1 - GENERAL 1.1 SUMMARY

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete Vapor-Shell GUIDE SPECIFICATION SECTION 09725 PART 1 GENERAL 1.01 SECTION INCLUDES A. Provisions

More information

Section RESILIENT TILE FLOORING INCLUDING ECONATURALS RUBBER FLOOR TILE

Section RESILIENT TILE FLOORING INCLUDING ECONATURALS RUBBER FLOOR TILE THIS DOCUMENT IS INTENDED AS A SUGGESTED GUIDE FOR CREATING, MODIFYING, OR EDITING YOUR CSI FORMATTED 3-PART ARCHITECTURAL GUIDE SPECIFICATIONS. TARKETT WILL NOT BE LIABLE FOR ANY DAMAGES ARISING OUT OF

More information

Decorative Quartz Floor Coating System

Decorative Quartz Floor Coating System Decorative Quartz Floor Coating System 1.01 - Work Included 1. Furnish necessary material, labor, and equipment required to prepare designated areas and install a DecoFloor Quartz System 2. Submit three

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 09 6623 - RESINOUS MATRIX TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX

SECTION EPOXY TERRAZZO TILE WITH RECYCLED GLASS MATRIX GlassPLANK GUIDE SPECIFICATION Manufacturer: GLASS RECYCLED LLC 2939 Irving Blvd Suite 305 Dallas TX 75247 (888) 523-7894 toll free voice www.glassrecycled.com SECTION 09 66 18 EPOXY TERRAZZO TILE WITH

More information

A. This Section includes traffic coatings for the following applications:

A. This Section includes traffic coatings for the following applications: SECTION 071800 - TRAFFIC COATINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes traffic coatings for the following applications: 1. Interior and exterior, pedestrian traffic. 2. Vehicular traffic.

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments SECTION 07 26 19 TOPICAL MOISTURE VAPOR EMISSION SYSTEM WITH ARDEX

More information

Wood Floor Bonding Systems

Wood Floor Bonding Systems Part 1 - General Wood Floor Bonding Systems DIVISION 9 - FINISHES Section 09 64 00 Wood Flooring Wood Parquet Flooring Spec Component: SC-302-0311 SikaBond-T21 1.01 Summary A. This specification describes

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 09 6613 - PORTLAND CEMENT TERRAZZO FLOORING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

DUR-A-FLEX, Inc. Page 1 of 6

DUR-A-FLEX, Inc. Page 1 of 6 DUR-A-FLEX, Inc. Page 1 of 6 SECTION 09 67 23-RESINOUS FLOORING DUR-A-CHIP EPOXY BROADCAST WITH URETHANE TOPCOAT Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings SECTION 07 26 19 TOPICAL MOISTURE VAPOR MITIGTION SYSTEM PART 1 - GENERAL

More information

SECTION LITHIUM BASED MOISTURE VAPOR CONTROL CURE SYSTEM AND FINISHING

SECTION LITHIUM BASED MOISTURE VAPOR CONTROL CURE SYSTEM AND FINISHING SECTION 033960 LITHIUM BASED MOISTURE VAPOR CONTROL CURE SYSTEM AND FINISHING PART 1 GENERAL 1.1 SECTION INCLUDES A. Work includes labor, materials, appliances, tools, equipment, facilities, transportation,

More information

Desco Mosaic Flooring Specifications

Desco Mosaic Flooring Specifications Desco Mosaic Flooring Specifications PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Sections, apply

More information

HI-TEK POLYMERS T-Poxy Terrazzo Arch Data

HI-TEK POLYMERS T-Poxy Terrazzo Arch Data HI-TEK POLYMERS T-Poxy Terrazzo Arch Data PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

A. Prepare formwork shop drawings using qualified professional engineer. Include detail of fabrication, assembly, and support of formwork.

A. Prepare formwork shop drawings using qualified professional engineer. Include detail of fabrication, assembly, and support of formwork. DIVISION 03 CONCRETE 03 0100 MAINTENANCE OF CONCRETE 03 0505 UNDER SLAB VAPOR BARRIER A. Sheet vapor retarder shall be polyethylene sheet, ASTM D 4397, 10 mils thick minimum. Consult with Facilities Management

More information

SECTION Verrazzo Epoxy Mosaic Floor System

SECTION Verrazzo Epoxy Mosaic Floor System THIS IS A SAMPLE SPECIFICATION FOR THE INDICATED PRODUCT. IT IS THE RESPONSIBILITY OF THE SPECIFIER AND/OR END USER TO DETERMINE THE SUITABILITY OF A PRODUCT OR SYSTEM FOR A PARTICULAR PURPOSE. Specifier

More information

SECTION EPOXY FLOORING SYSTEMS

SECTION EPOXY FLOORING SYSTEMS SECTION 09800 EPOXY FLOORING SYSTEMS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION (07100) - DAMPPROOFING AND WATERPROOFING

SECTION (07100) - DAMPPROOFING AND WATERPROOFING SECTION 07 10 00 (07100) - DAMPPROOFING AND WATERPROOFING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Sheet Membrane Waterproofing 2. Under-Slab-On-Grade Vapor Barrier B. Related Sections: 1.02

More information

SECTION TILING

SECTION TILING PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 800.323.7357 863.967.1535 fax:863-965.2326 Seal-Krete High Performance Epoxy Metallic System GUIDE SPECIFICATION SECTION 09725 PART 1 GENERAL

More information

ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface

ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and

More information

SECTION A. American Society for Testing and Materials (ASTM):

SECTION A. American Society for Testing and Materials (ASTM): hp.seal-krete.com 306 Gandy Rd., Auburndale, FL 33823-2723 863.967.1535 800.323.7357 fax: 863-965.2326 Seal-Krete High Performance Poly-Shell 7000 Sparse Flake System GUIDE SPECIFICATION SECTION 09725

More information

Consult Sika Corporation (Industrial Flooring) for assistance in editing this section for the specific application.

Consult Sika Corporation (Industrial Flooring) for assistance in editing this section for the specific application. THIS IS A SAMPLE SPECIFICATION FOR THE INDICATED PRODUCT. IT IS THE RESPONSIBILITY OF THE SPECIFIER AND/OR END USER TO DETERMINE THE SUITABILITY OF A PRODUCT OR SYSTEM FOR A PARTICULAR PURPOSE. Specifier

More information

ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment

ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment ARDEX GUIDE SPECIFICATION ARDEX GPS GENERAL PATCH & SKIMCOAT Trowelable underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions

More information

Powerdek Fleck. SECTION Resilient Athletic Flooring

Powerdek Fleck. SECTION Resilient Athletic Flooring SECTION 09622 Resilient Athletic Flooring PART 1: GENERAL 1.0 SUMMARY 1.0.1 Work Included A. Prefabricated Rubber Sports Flooring B. Adhesive and accessories required for installation and maintenance 1.0.2

More information

Seal- Krete High Performance System

Seal- Krete High Performance System hp.seal-krete.com Rust-Oleum - 11 Hawthorn Parkway, Vernon Hills, IL 800.323.7357 PART 1 GENERAL 1.01 SECTION INCLUDES Seal- Krete High Performance Poly- Shell 70007 System GUIDE SPECIFICATION SECTION

More information

1. ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers-Tension.

1. ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers-Tension. 3-Part Specification: ElastoFloor Roll-Pour Surface America, Inc. PO Box 157 Williamsville, NY 14231 Phone: (800) 999-0555 Phone: (716) 632-8413 Fax: (716) 632-8324 info@surfaceamerica.com www.surfaceamerica.com

More information

SPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay

SPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay 2004 Specifications SPECIAL SPECIFICATION 4429 Multiple-Layer Polymer Concrete Overlay 1. Description. Furnish and place a multi-layer polymer overlay consisting of a crack seal, polymer resin and aggregates.

More information

DIVISION 7 THERMAL AND MOISTURE PROTECTION Section Traffic Coatings

DIVISION 7 THERMAL AND MOISTURE PROTECTION Section Traffic Coatings Spec Component: SC-720-03/10 Sikalastic 720/745 Traffic System DIVISION 7 THERMAL AND MOISTURE PROTECTION Section 071800 Traffic Coatings Part 1 - General 1.01 Summary A. This specification describes the

More information

Specifications. Specifications (Architectual) Metallic System. Metallic System

Specifications. Specifications (Architectual) Metallic System. Metallic System (Architectual) Metallic System Architectual NeverStrip Floor Coatings, 6-15 Mils Master Format Section 096700 Fluid Applied Flooring 1 of 6 NeverStrip Metallic High-Build Decorative Epoxy/Urethane Coating

More information

Section RESILIENT SAFE-T VINYL SHEET FLOORING

Section RESILIENT SAFE-T VINYL SHEET FLOORING RESILIENT SAFE-T VINYL SHEET FLOORING THIS DOCUMENT IS INTENDED AS A SUGGESTED GUIDE FOR CREATING, MODIFYING, OR EDITING YOUR CSI FORMATTED 3-PART ARCHITECTURAL GUIDE SPECIFICATIONS. TARKETT WILL NOT BE

More information

Vapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring

Vapor-Clear. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring advanced moisture control, inc. The high-performance, low-cost, eco-friendly, aesthetically-pleasing alternative to high-build epoxy floors and boring 250 polished concrete slabs! Made in Southern California,

More information

Application Specification:

Application Specification: Application Specification: GW-15-UBU-HD April 2014 Supersedes 5/13 PART 1 - GENERAL 1.1 SUMMARY Division 07 18 16: GACOFLEX POLYURETHANE ELASTOMERIC COATING SYSTEM FOR VEHICULAR TRAFFIC DECKS AND RAMPS

More information

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating. This specification covers an epoxy wall coating system composed of an epoxy block filler, one or two applications of a flexible hybrid polymer basecoat, and top coat of high-performance aliphatic satin

More information

B. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.

B. Related Sections: 1. Division 07 Section Joint Sealants for sealing of expansion, contraction, control, and isolation joints in tile surfaces. SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

ARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish

ARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish ARDEX GUIDE SPECIFICATION ARDEX SD-M Designer Floor Finish SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract,

More information