SECTION GYPSUM BOARD
|
|
- Ross Johnson
- 5 years ago
- Views:
Transcription
1 SECTION GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Interior gypsum wallboard. 2. Tile backing panels. B. Related Sections: 1. Section Alternates. 1.2 SUBMITTALS A. Product Data: For each product indicated. B. Samples: For the following products: 1. Trim Accessories: Full-size Sample in 12-inch long length for each trim accessory indicated. 1.3 QUALITY ASSURANCE A. Mock-ups: Before beginning gypsum board installation, install a mock-up of at least 100 square feet in surface area to demonstrate aesthetic and set quality standards for materials and execution at location to be determined by Architect. 1. Install mock-ups for each level of gypsum board finish indicated for use in exposed locations. 2. Apply or install final decoration indicated, including painting, on exposed surfaces for review of mock-ups. 3. Simulate finished lighting conditions for review of mock-ups. 4. Approved mock-ups may become part of completed Work if undisturbed at time of Substantial Completion. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Gypsum Materials: Subject to compliance with requirements, provide products from 1 of the following manufacturers: 1. American Gypsum Co. 2. BPB America Inc. 3. G-P Gypsum Corp. 4. Lafarge North America Inc. 5. National Gypsum Company. 6. PABCO Gypsum. 7. Temple-Inland. 8. USG Corporation. 9. Approved Substitutions. 2.2 GYPSUM WALLBOARD A. Panel Size: Provide in maximum lengths and widths available that will minimize joints in each area and correspond with support system indicated. INTERIORS PACKAGE OF 6 GYPSUM BOARD
2 B. Fire-Rated Gypsum Board (GWB-1): ASTM C36; gypsum core wall panel with additives to enhance fire resistance of core and surfaced with paper on front, back and long edges; Type X, UL rated. C. Fire-Rated Moisture Resistant Gypsum Board (GWB-2): ASTM C630; gypsum core wall panel with additives to enhance fire resistance of core and water resistance of core. Surface with water repellent paper on front, back, and long edges; Type X, UL rated. 3. Acceptable products: SheetRock Brand Mold Tough Firecode Gypsum Panels by USG Corporation or approved substitution. D. Moisture-Resistant Gypsum Board (GWB-3): ASTM 3273; engineered gypsum/cellulose-fiber combination core wall panel with additives to enhance fire resistance of core and surfaced with fiberreinforced front, back, and long edge. Type X, UL rated. 1. Maximum framing spacing is 16 inches on center. 2. Size: 5/8 inch thick by 36 inches wide by 5 feet long. 3. Edges: Cut square. 4. Acceptable Products: a. Custom Building Products: Wonderboard. b. FinPan, Inc.: Util-A-Crete Concrete Backer Board. c. USG Corporation.: FibeRock Aqua-Tough Gypsum Panels. E. Fire-Rated, Fiber-Reinforced, Abuse-Resistant Gypsum Board (GWB-4): ASTM C1278; fiberglass reinforced gypsum core wall panel with additives to enhance fire resistance of core and surfaced with heavy natural finish paper on front, back, and long edge. Type X, UL rated. 3. Acceptable products: a. G-P Gypsum Corporation: ToughRock Abuse-Resistant Gypsum Board. b. National Gypsum Company: Gold Bond Hi-Abuse Wallboard. c. USG Corporation: SheetRock Brand Abuse-Resistant Gypsum Panels. F. Ceiling Type (GWB-5): ASTM C36; gypsum core ceiling panel with additives to enhance sag resistance of core. Surface with paper on front, back, and long edges. G. High-IMpact Gypsum Board (GWB-6): ASTM C1278; fiberglass reinforced gypsum core wall panel with additives to enhance fire resistance of core and surfaced with heavy natural finish paper on front, back, and long edge. Type X, UL rated. 2. Edges: Square cut, tapered long edges for joint reinforcement. 3. Acceptable products: a. USG Corporation.: FibeRock VHI Brand Abuse-Resistant Gypsum Panels or approved substitution. 2.3 TRIM ACCESSORIES A. Interior Trim: ASTM C Material: Paper-faced galvanized steel sheet. 2. Shapes: a. Cornerbead. b. LC-Bead: J-shaped; exposed long flange receives joint compound. c. L-Bead: L-shaped; exposed long flange receives joint compound. GYPSUM BOARD OF 6 INTERIORS PACKAGE
3 d. U-Bead: J-shaped; exposed short flange does not receive joint compound. e. Expansion (control) joint. f. Curved-Edge Cornerbead: With notched or flexible flanges. 2.4 JOINT TREATMENT MATERIALS A. General: Comply with ASTM C475/C475M. B. Joint Tape: 1. Interior Gypsum Wallboard: Paper as recommended by manufacturers. 2. Tile Backing Panels: As recommended by panel manufacturer. C. Joint Compound for Interior Gypsum Wallboard: For each coat use formulation that is compatible with other compounds applied on previous or for successive coats. 1. Prefilling: At open joints, beveled panel edges, and damaged surface areas, use setting-type taping compound. 2. Embedding and First Coat: For embedding tape and first coat on joints, fasteners, and trim flanges, use setting-type taping compound. a. Use setting-type compound for installing paper-faced metal trim accessories. 3. Fill Coat: For second coat, use drying-type, all-purpose compound. 4. Finish Coat: For third coat, use drying-type, all-purpose compound. D. Joint Compound for Tile Backing Panels: 1. Water-Resistant Gypsum Backing Board: Use setting-type taping and setting-type, sandable topping compounds. 2.5 SOUND ATTENUATION INSULATION A. Provide sound-attenuating materials with a flame spread index of 0 and smoke developed index of 0 when tested per ASTM E Recycled Content: Provide blankets with recycled content such that postconsumer recycled content plus 1/2 of preconsumer recycled content constitutes a minimum of 90 percent by weight. 2. See Sound Attenuation Insulation schedule on Sheet A3.00 for acoustical insulation locations in gypsum board ceilings. 2.6 AUXILIARY MATERIALS A. General: Provide auxiliary materials that comply with referenced installation standards and manufacturer's written recommendations. B. Laminating Adhesive: Adhesive or joint compound recommended for directly adhering gypsum panels to continuous substrate. 1. Use adhesives that have a VOC content of 50 g/l or less when calculated per 40 CFR 59, Subpart D (EPA Method 24). C. Steel Drill Screws: ASTM C1002, unless otherwise indicated. 1. Use screws complying with ASTM C954 for fastening panels to steel members from to inch thick. 2. For fastening cementitious backer units, use screws of type and size recommended by panel manufacturer. D. Acoustical Sealant: As specified in Section Joint Sealants. E. Thermal Insulation: As specified in Section Thermal Insulation. F. Provide other materials, not specifically described, but required for complete and proper installation, as selected by Contractor subject to approval of Architect. INTERIORS PACKAGE OF 6 GYPSUM BOARD
4 PART 3 - EXECUTION 3.1 APPLYING AND FINISHING PANELS, GENERAL A. Comply with ASTM C840. B. Examine panels before installation. Reject panels that are wet, moisture damaged, and mold damaged. C. Install ceiling panels across framing to minimize number of abutting end joints and to avoid abutting end joints in central area of each ceiling. Stagger abutting end joints of adjacent panels not less than 1 framing member. D. Install panels with face side out. Butt panels together for a light contact at edges and ends with not more than 1/16 inch of open space between panels. Do not force into place. E. Locate edge and end joints over supports, except in ceiling applications where intermediate supports or gypsum board back-blocking is provided behind end joints. Do not place tapered edges against cut edges or ends. Stagger vertical joints on opposite sides of partitions. Do not make joints other than control joints at corners of framed openings. F. Form control and expansion joints with space between edges of adjoining gypsum panels. G. Cover both faces of support framing with gypsum panels in concealed spaces (above ceilings, etc.), except in chases braced internally. 1. Unless concealed application is indicated or required for sound, fire, air, or smoke ratings, coverage may be accomplished with scraps of not less than 8 square feet in area. 2. Fit gypsum panels around ducts, pipes, and conduits. 3. Where partitions intersect structural members projecting below underside of floor/roof slabs and decks, cut gypsum panels to fit profile formed by structural members; allow 1/4 to 3/8 inch wide joints to install sealant. H. Isolate perimeter of gypsum board applied to non-load-bearing partitions at structural abutments, except floors. Provide 1/4 to 1/2 inch wide spaces at these locations, and trim edges with edge trim where edges of panels are exposed. Seal joints between edges and abutting structural surfaces with acoustical sealant. I. Attachment to Steel Framing: Attach panels so leading edge or end of each panel is attached to open (unsupported) edges of stud flanges first. 3.2 ACOUSTICALLY RATED PARTITIONS A. Install sound attenuation blankets before installing gypsum panels, unless blankets are readily installed after panels have been installed on one side. 1. See Sheet A6.01 for location of acoustically rated partitions. B. Acoustically Rated Partitions: Seal construction at perimeters, behind control joints, and at openings and penetrations with continuous bead of acoustical sealant. Install acoustical sealant at both faces of partitions at perimeters and through penetrations. Comply with ASTM C919 and with manufacturer's written recommendations for locating edge trim and closing off sound-flanking paths around or through assemblies, including sealing partitions above acoustical ceilings. C. Acoustical sealant shall close gaps between service outlets (electrical, telephone and data) and wallboard. 1. Apply continuous bead of acoustical sealant between bottom track and slab at all locations, not just at acoustically rated partitions. 2. Apply acoustical sealant to back of electrical J-boxes for power, telephone and data prior to installation of gypsum wallboard. D. Partitions shall be cut and sealed around structural elements. GYPSUM BOARD OF 6 INTERIORS PACKAGE
5 E. No wallboard layers shall be continuous between 2 adjacent rooms. F. Gaps around penetrations (ducts, pipes and conduit) shall be sealed as follows: 1. Tightly fill gaps 1 inch or less with attenuation batt insulation. 2. Fill gaps larger than 1 inch with heavy-density putty such as 3M Moldable Putty. 3.3 APPLYING INTERIOR GYPSUM BOARD A. Install interior gypsum board in the following locations: 1. GWB-1: Use throughout except where indicated otherwise. 2. GWB-5: Ceiling surfaces where indicated on Drawings. 3. GWB-2 and -3: As indicated on Drawings. 4. GWB-4: Use per Add Alternate-6. See Sheet A2.03 for scope. 5. GWB-6: Use in horizontal applications at exposed lid of Entry Block as indicated on Sheet A APPLYING TILE BACKING PANELS A. GWB-3: Install where indicated. Install with 1/4 inch gap where panels abut other construction or penetrations. B. Areas Not Subject to Wetting: Install regular-type gypsum wallboard panels to produce a flat surface except at showers, tubs, and other locations indicated to receive water-resistant panels. C. Where tile backing panels abut other types of panels in same plane, shim surfaces to produce a uniform plane across panel surfaces. 3.5 INSTALLING TRIM ACCESSORIES A. General: For trim with back flanges intended for fasteners, attach to framing with same fasteners used for panels. Otherwise, attach trim per manufacturer's written instructions. B. Control Joints: Install control joints per ASTM C840 and GA-216, and in specific locations indicated on Drawings. 1. Advise Architect if additional control joints are required or necessary per referenced standards, and provide these control joints at no additional Cost to Owner. C. Interior Trim: Install in the following locations: 1. Cornerbead: Use at outside corners, unless otherwise indicated. 3.6 FINISHING GYPSUM BOARD A. General: Treat gypsum board joints, interior angles, edge trim, control joints, penetrations, fastener heads, surface defects, and elsewhere as required to prepare gypsum board surfaces for decoration. Promptly remove residual joint compound from adjacent surfaces. B. Prefill open joints, rounded or beveled edges, and damaged surface areas. C. Apply joint tape over gypsum board joints, except those with trim having flanges not intended for tape. D. Gypsum Board Finish Levels: Finish panels to levels indicated below, per ASTM C840, for locations indicated: 1. Base Level: No taping, finishing, or accessories required. a. Use above suspended ceilings and within other concealed spaces, unless assembly is fire rated, sound rated, sound or smoke controlled, or unless space serves as an air plenum. 2. Level 1: Embed tape in joint compound at joints. Leave surface free of excess joint compound. Tool marks and ridges are acceptable. INTERIORS PACKAGE OF 6 GYPSUM BOARD
6 a. Use above suspended ceilings and within other concealed spaces where gypsum board assembly serves as an air plenum. 3. Level 2: Embed tape in joint compound at joints and apply 1 separate coat of joint compound applied over joints, angles, fastener heads, trim flanges, and accessories. Provide Level 2 finish at the following conditions: a. Water resistant gypsum board indicated for use as substrate for ceramic tile. 4. Level 4: Embed tape in joint compound at joints and apply 3 separate coats of joint compound applied over joints, angles, fastener heads, trim flanges, and accessories. Apply joint compound smooth and free of tool marks and ridges. Provide Level 4 finish at the following conditions: a. Gypsum board indicated to be exposed to view except where indicated for other finish levels. 3.7 PROTECTION A. Protect installed products from damage from weather, condensation, direct sunlight, construction, and other causes during remainder of construction period. B. Remove and replace panels that are wet, moisture damaged, and mold damaged. 1. Indications that panels are wet or moisture damaged include discoloration, sagging, or irregular shape. 2. Indications that panels are mold damaged include fuzzy or splotchy surface contamination and discoloration. END OF SECTION GYPSUM BOARD OF 6 INTERIORS PACKAGE
Chevy Chase Club June 30, 2008 Bowie Gridley Architects
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationA. Environmental Limitations: Comply with ASTM C 840 requirements or gypsum board manufacturer's written instructions, whichever are more stringent.
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationCOOK COUNTY ILLINOIS CONTRACT FOR WORK DOCUMENT NO Countywide Warehouse and Records Storage Center Hawthorne Project TKB No.
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION GYPSUM BOARD
SECTION 092900 GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationGYPSUM BOARD
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationIce Rink Renovation & New Clubhouse
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationAsh Brook Golf Course Scotch Plains, New Jersey
SECTION 092500 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationStudent Services & Classroom Addition
SECTION 092900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation blankets
SECTION 09 29 00 - GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Interior gypsum board. 2. Glass-mat gypsum sheathing board for ceilings and soffits. 3. Cement board. 4. Sound attenuation
More informationCONTRACT NUMBER: W912DQ-08-C % CORRECTED DESIGN 28 JULY 2008
SECTION 092900 - GYPSUM BOARD 1.1 SUMMARY A. This Section includes the following: 1. Interior gypsum board. 2. Tile backing panels. B. Related Sections include the following: 1. Division 06 Section "Rough
More informationChevy Chase Club June 30, 2008 Bowie Gridley Architects SECTION GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSAN DIEGO STATE UNIVERSITY PACIFIC CORNERSTONE ARCHITECTS TENOCHCA HALL PROJECT NO FAN COIL UNITS, RESTROOM AND FINISH RENOVATION
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Various gypsum board panels types. 2. Joint treatment materials. 3. Panel trim. 4. Supplementary components and accessories
More informationRAMAPO COLLEGE OF NEW JERSEY PHASE II HOUSING REHABILITATION C 2012
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD
Manufacturer: American Gypsum 3811 Turtle Creek Blvd., Suite 1200 Dallas, Texas 75219 (800) 545-6302 (214) 530-5634 fax www.americangypsum.com GUIDE SPECIFICATION SECTION 09 29 00 This guide specification
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationSECTION GYPSUM BOARD SYSTEM
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 09 29 00 GYPSUM BOARD SYSTEM A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 specification sections,
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2900 - GYPSUM BOARD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 - GENERAL 1.1 SUMMARY SECTION 09 21 16 A. Provide gypsum board assemblies as shown and specified. Work includes: 1. Walls, partitions, and soffits, including metal framing systems. 2. Acoustical
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092650 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationA. Product Data: For each type of product specified.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More information1. Interior gypsum wallboard. 2. Exterior gypsum board panels for ceilings and soffits. 3. Tile backing panels.
SECTION 09260 - GYPSUM BOARD ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Section Includes 1. Gypsum board screw attached to wood framing and furring members, joint treatment, and accessories. 2. Installation of
More informationSECTION GYPSUM BOARD
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 29 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION GYPSUM BOARD ASSEMBLIES
PART 1 GENERAL 1.01 SECTION INCLUDES SECTION 09260 - A. Metal stud wall framing. Denoted on drawings as "metal studs". B. Metal channel ceiling framing. C. Acoustic insulation and sealant. D. Cementitious
More informationGypsum Board
University of New Hampshire University of New Hampshire Scholars' Repository Division 09 Finishes Chapter 5 Technical Construction and Renovation Standards 1-25-2013 092900 - Gypsum Board Sandra Hickey
More information1. Nonload-bearing steel framing members for gypsum board assemblies. 2. Gypsum board assemblies attached to steel framing.
SECTION 09250 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this
More informationSECTION GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.01 SECTION INCLUDES
SECTION 09 2116 - PART 1 GENERAL 1.01 SECTION INCLUDES A. Performance criteria for gypsum board assemblies. B. Acoustic insulation. C. Gypsum sheathing. D. Cementitious backing board. E. Gypsum wallboard.
More informationEXCEL Medical Waste - Equipment Installation Section SECTION GYPSUM BOARD
SECTION 09 29 00 GYPSUM BOARD PART 1 - GENERAL 1.1 DESCRIPTION This section specifies installation and finishing of gypsum board. 1.2 RELATED WORK A. Installation of steel framing members for walls, partitions,
More informationRENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11
SECTION 09 29 00 GYPSUM BOARD 05/11 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text
More informationSECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board
SECTION 09260 GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard
More informationConstruction Standards PAGE
Construction Standards PAGE 092613-1 SECTION 092613 - PART 1 - GENERAL 1.1 M.S.U. ISSUES A. It is the intent of MSU that all gypsum veneer plaster used on its projects will comply with LEED NC 3 Credit
More informationSECTION GYPSUM BOARD
SECTION 09250 GYPSUM BOARD PART 1GENERAL 1.1 SUMMARY A. Related Documents: General and Supplementary Conditions of the Contract, Division 1 - General Requirements, and Drawings are collectively applicable
More informationONE SCHOOL STREET SEPTEMBER 18, 2008 GOWANDA, NEW YORK ARCH PROJECT NO
SECTION 09265 - GYPSUM BOARD SHAFT-WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION GYPSUM BOARD & SHEATHING SYSTEMS
PART 1!GENERAL! 1.01! SECTION INCLUDES SECTION 09260 GYPSUM BOARD & SHEATHING SYSTEMS! Metal stud wall framing. Metal channel ceiling framing.! Gypsum board.! Sheathing.! Taped and sanded joint treatment.!
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 6
DECEMBER, 2016 Page 1 of 6 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 07 21 16 - Batt and Blanket Insulation..3 Section 07 92 10 - Sealants..4 Section 09 91 00
More informationA. Extent of each type of gypsum drywall construction required is indicated on the Drawings.
09250 GYPSUM WALLBOARD PART 1 - GENERAL 1.1 STIPULATIONS A. The specifications sections " General Conditions of the Construction Contract ", "Special Conditions", and "Division 1 - General Requirements"
More informationCopyright 2010 AIA MasterSpec Short Form 02/10 PRODUCT MASTERSPEC LICENSED BY ARCOM TO GEORGIA-PACIFIC GYPSUM LLC
This Product MasterSpec Section is licensed by ARCOM to Georgia-Pacific Gypsum LLC ("Licensee"). This Product MasterSpec Section modifies the original MasterSpec text, and does not include the full content
More informationSECTION GYPSUM BOARD PART 1 - GENERAL
SECTION 09250 - GYPSUM BOARD PART 1 - GENERAL 1.01 DESCRIPTION: A. Work under this section is subject to requirements of the Contract Documents including the General Conditions and Supplementary Conditions
More informationSECTION GYPSUM BOARD ASSEMBLIES
1 PART ONE - GENERAL 1.1 COORDINATION SECTION 09260 GYPSUM BOARD ASSEMBLIES A. Drawings and General provisions of the Contract including General and Supplementary Conditions and Division 1 Specification
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09 21 16 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SECTION INCLUDES A. Metal stud wall and ceiling framing, 20 gauge. B. Metal channel suspended ceiling framing. C. Gypsum board. D. Gypsum sheathing.
More informationNATIONAL GYPSUM COMPANY Wood Frame Walls And Ceilings Single- And Double-Layer Construction
Walls And Ceilings Single- And Double-Layer Construction 09 9 00/NGC Single-Layer Construction The single-layer construction system consists of a single layer of Gold Bond brand Gypsum Board applied to
More informationSECTION GYPSUM BOARD SYSTEM
SECTION 09 29 00 GYPSUM BOARD SYSTEM PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,
More informationSECTION GYPSUM BOARD
SECTION 09 2900 GYPSUM BOARD PART 1 - GENERAL 1.1 SUMMARY A. Includes But Not Limited To: 1. Furnish and install gypsum board as described in Contract Documents, except behind ceramic tile. 2. Furnish
More informationSECTION GYPSUM BOARD ASSEMBLIES
SECTION 09260 GYPSUM BOARD ASSEMBLIES PART 1 GENERAL 1.1 SUMMARY A. Provide gypsum board assemblies. 1.2 SUBMITTALS A. Product Data: Submit manufacturer's product data and installation instructions for
More informationRhode Island College - Recreation Center, Providence, RI June 7, 2010 Designpartnerhip of Cambridge Inc., 2909 SECTION
SECTION 09 2116.23 GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationUniversity of Missouri St. Louis UMSL Project No. S Thomas Jefferson Library Elevator R&B Project No: Renovation & Repairs
SECTION 092116.23 - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION GYPSUM BOARD
SECTION 09260 - GYPSUM BOARD PART 1 - GENERAL 1.01 SUMMARY A. Related Documents: Provisions established in General and Supplementary Conditions of the Contract, Division 1 General Requirements, and the
More informationSECTION (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES
SECTION 09 21 16.23 (09265) - GYPSUM BOARD SHAFT WALL ASSEMBLIES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Shaft Enclosures 2. Chase Enclosures 3. Stair Enclosures B. Related Sections: 1.02 DEFINITIONS
More informationFoil Back Gypsum Board
BRAND 09 29 00/NGC Foil Back Gypsum Board brand Foil Back Gypsum Board consists of a fire-resistant gypsum core with a heavy, natural finish and 100-percent recycled paper on the face and a strong liner
More informationGYPSUM BOARD SECTION GYPSUM BOARD PART 1 - GENERAL
13686.00 GYPSUM BOARD 092116-1 1.1 RELATED DOCUMENTS: SECTION 092116 - GYPSUM BOARD PART 1 - GENERAL A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division
More informationConstruction Standards PAGE
Construction Standards PAGE 095113-1 SECTION 095113 - PART 1 - GENERAL 1.1 M.S.U. ISSUES 1. It the intent of MSU that all joint sealants used on its projects will comply with LEED NC 3 Credit Requirements
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2013 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2013 Application and Finishing of Gypsum Panel Products. Each
More information1 Exam Prep Application and Finishing of Gypsum Board GA Tabs and Highlights
1 Exam Prep Application and Finishing of Gypsum Board GA-216-2016 Tabs and s These 1 Exam Prep Tabs are based on the Gypsum Association GA-216-2016 Application and Finishing of Gypsum Panel Products. Each
More informationA. This Section includes non-load-bearing steel framing members for the following applications:
SECTION 092210 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationGold Bond BRAND Kal-Kore Plaster Base
BRAND 09 29 22 00/NGC 39/NGC Kal-Kore Plaster Base brand Kal-Kore Plaster Base is a tapered-edge gypsum plaster base with 100-percent recycled gray absorptive face paper surface designed to permit rapid
More informationSAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. SECTION GYPSUM BOARD ASSEMBLIES
SAMPLE CONSTRUCTION SPECS 2011 Conspectus, Inc. Specifications, Quality Assurance, Inspections & Investigations for Your Construction Projects 2231 ROUTE 50 P.O. BOX 248 TUCKAHOE, NJ 08250 p: 609.628.2390
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 095113 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 092216 - COLD FORMED STEEL FRAMING - NON-STRUCTURAL (CFSF-NS) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ACTION
More informationStore No MAY 13 Addendum No. 1 SECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSECTION CEMENTITIOUS SHEATHING
SECTION 06 16 63 CEMENTITIOUS SHEATHING SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this Section for exterior sheathing as a backup
More informationA. All materials and workmanship shall be warranted against defects for a period of two (2) years from the date of receipt at the project site.
SECTION 092119 - BULLET RESISTANT FIBERGLASS UL752 Level 3 PART 1 - GENERAL 1.1. REFERENCE A. The publications listed below form a part of this specification. 1. UNDERWRITERS LABORATORY UL 752 10th Edition,
More informationRLGA. Gypsum Board Construction 2012 International Building Code. By Ronald L. Geren, AIA, CSI, CCS, CCCA, SCIP
Gypsum Board Construction 2012 International Building Code By Ronald L. Geren, AIA, CSI, CCS, CCCA, SCIP Gypsum board has been an important part of the construction industry for more than 100 years. Its
More informationSECTION NON-STRUCTURAL METAL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 22 16 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More information138 H-STUD AREA SEPARATION WALL SYSTEM
H-STUD AREA SEPARATION WALL SYSTEM The fire-protection of gypsum-based Area Separation Walls is demonstrated in dramatic fashion by the results of this actual townhouse fire in which the two-hour fire-rated
More informationB. Do not install interior products until installation areas are enclosed and conditioned.
GYPSUM BOARD SHAFT WALL ASSEMBLIES Section 09 2116.23 Page 1 of 6 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationB. Evaluation Reports: Provide ICC-ESR numbers and LARR identification numbers for Metal Studs, Fasteners, and Suspension Ceilings.
SECTION 09 22 16 NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes non-structural metal framing assemblies. 1.2 ASSEMBLY PERFORMANCE REQUIREMENTS 1. Typical Walls: Wall
More informationSECTION SOUND-ABSORPTIVE PANELS
SECTION 09 77 23 SOUND-ABSORPTIVE PANELS PART 1 - GENERAL 1.1 CONDITIONS AND REQUIREMENTS A. The General Conditions, Supplementary Conditions, and Division 01 General Requirements apply. 1.2 SECTION INCLUDES
More informationSALEM REGIONAL MEDICAL CENTER 09/2016 Firestone Farms MOB Salem, OH
SECTION 09111 - NON-LOAD-BEARING STEEL FRAMING 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationHigh Flex Gypsum Board
BRAND 09 29 00/NGC High Flex brand High Flex consists of a fire-resistant gypsum core encased in a heavy, natural finish with 100-percent recycled paper on the face and back sides. The face paper is folded
More informationHigh Strength LITE Gypsum Board
BRAND 09 29 00/NGC High Strength LITE brand High Strength LITE consists of a fire-resistant gypsum core with a heavy, natural finish and 100-percent recycled paper on the face and back sides. It is formulated
More informationCGC FIBEROCK BRAND AQUA-TOUGH AR INTERIOR PANEL
CGC Interior Panel & Finishing Solutions DATA SHEET CGC FIBEROCK BRAND AQUA-TOUGH AR INTERIOR PANEL Gypsum fiber panels outperform paper-faced gypsum board in abuse-prone areas Aqua-Tough formulation provides
More informationNATIONAL GYPSUM COMPANY 3-Hour Area Separation Wall System
-Hour Wall System The -hour Wall System is a -hour fire wall consisting of two layers of in. (. mm) shaftliner panels friction-fit between in. (0. mm) light-gauge steel H-Studs and a layer of /" Fire-Shield
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationUniSpec II - Store Planning
UniSpec II - Store Planning 072613 SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Suspended metal grid ceiling system. 2. Acoustical panels. 3. Perimeter
More informationA. This Section includes ceilings consisting of acoustical panels and exposed suspension systems.
SECTION 09 51 13 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationProduct Specification
General Specification Notes: SECTION 09210 / 09 21 00\ Finish Coat Plasters References in blue are general indicators to the specifier. References in red relate to fire-rated assemblies and/or code related
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION FURRING AND LATHING. A. This section specifies providing furring, lathing and accessories.
SECTION 09205 FURRING AND LATHING PART 1 - GENERAL 1.01 DESCRIPTION: A. This section specifies providing furring, lathing and accessories. B. Related Work Specified Elsewhere: 1. Access Doors and Frames:
More informationUse it for interior wall and ceiling applications and in areas with limited water exposure.
09 29 00/NGC Hi-Impact XP Gold Bond brand Hi-Impact XP consists of a mold-, mildew-, moisture- and fire-resistant Type X gypsum core with a specially designed PURPLE paper. The PURPLE face paper is a heavy
More informationThe GlasRoc Shaftliner Type X advantage...
C e r t a i n T e e d SHAFTLINER F o r A r e a S e p a r a t i o n F i r e w a l l s Shaftliner S Type X for Area Separation GlasRoc Shaftliner is a specially formulated product for applications where
More informationSECTION LINEAR METAL CEILINGS
SECTION 09 5423 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationMulti-Institutional Academic Health Science & Research Center Evansville, IN
SECTION 061600 - SHEATHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. AC: Articulation
More informationEDGEWATER, FLORIDA JUNE 14, 2010
SECTION 09 2400 - PORTLAND CEMENT PLASTER PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationCertainTeed. GlasRoc. Tile Backer
CertainTeed GlasRoc TM Diamondback GlasRoc Product Overview is a superior tile substrate for walls, ceilings, and countertops, specially designed by CertainTeed to meet the demands of highmoisture areas.
More informationSECTION ACOUSTICAL CEILINGS
PART 1- GENERAL 1.1 DESCRIPTION SECTION 09 51 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION THROUGH-PENETRATION FIRESTOP SYSTEMS
SECTION 07841 - THROUGH-PENETRATION FIRESTOP SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION NON--STRUCTURAL METAL FRAMING
The Collective Voice of America s Steel Framing Industry The Steel Framing Industry Association (SFIA) is dedicated to expanding the market for cold-formed steel in construction through programs and initiatives
More informationSECTION ACOUSTICAL PANEL CEILINGS. A. Section includes acoustical panels and exposed suspension systems for ceilings.
SECTION 09 51 13 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 SUMMARY A. Section includes acoustical panels and exposed suspension systems for ceilings. 1.2 SUBMITTALS A. Product Data: For each type
More informationConstruction Standards PAGE
Construction Standards PAGE 072100-1 SECTION 072100 PART 1 - GENERAL 1.1 M.S.U. ISSUES A. It the intent of MSU that insulation of its projects will comply with LEED NC 3 Credit Requirements EA Prerequisite
More informationSection GYPSUM DRYWALL
Section 09250 GYPSUM DRYWALL 1.00 GENERAL: A. Gypsum Association Specification GA216 and manufacturer's instruction (whichever is more stringent). 2.00 DRYWALL MATERIALS: A. Exposed Gypsum Board: ASTM
More informationRichmond Hill High Renovation DOCUMENT ADDENDA No. 3
DOCUMENT 00 9113 ADDENDA No. 3 1.1 PROJECT INFORMATION A. Project Name : Richmond Hill High School Renovations Bryan County, Georgia B. Owner: Bryan County Public Board of Education 8810 Highway 280 Black
More informationSECTION THERMAL INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 072100 - THERMAL INSULATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationAssemblies Evaluated For 1. Non Axial Load Bearing Wall 2. Transverse Load Capacity 3. Fire Resistance 4. Abuse Resistance
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Assembly Evaluation Report represents a product that Pei ES has Evaluated. This Assembly Evaluation
More informationGold Bond BRAND Gypsum Sheathing
BRAND 09 06 29 16 00/NGC 43/NGC brand is a moisture-resistant sheathing installed on the outside of exterior framing as a substrate for exterior claddings. It is manufactured with a treated water-resistant
More information