SUNY GENESEO RED JACKET DINING HALL RENOVATION THIN BRICK MASONRY

Size: px
Start display at page:

Download "SUNY GENESEO RED JACKET DINING HALL RENOVATION THIN BRICK MASONRY"

Transcription

1 SUNY GENESEO SECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Adhesive adhered, solid, manufactured thin brick veneer for interior individual unit application on rigid backer board over building substrate. 2. Adhesives, fasteners and mortar. 3. Masonry Sealant. B. Related sections: 1. Section Submittal Procedures 2. Section Sustainable Design Requirements-LEED 2009 for Commercial Interiors 3. Section Brick Masonry 4. Section "Sealants" for sealants at control joints and intersections with dissimilar materials. 5. Section "Gypsum Board Assemblies" for interior wall framing and tile backing board substrates. 1.3 SUBMITTALS A. Product Certificates: Credit MR5, For regional materials, indicating location of material manufacturer and point of extraction, harvest, or recovery for each raw material. Include distance to Project and cost for each regional material. B. Product Data: Submit for all specified products. Include all applicable physical and performance data. C. Samples: Submit 4 samples of thin brick/panel brick veneer units to illustrate color, texture, and size range of each type unit. D. Manufacturer's detailed installation instructions. 1.4 FIELD SAMPLES A. Sample Installation: Construct thin mockup, including sub-framing, substrate surfaces, fasteners, adhesive bonding, joint work, moisture barrier, grout color, expansion joints and control joints.

2 SUNY GENESEO B. Obtain Architect s approval before beginning work. Protect and retain sample as a basis on which the quality of the work will be judged. C. Accepted Field Sample: May remain as part of completed Work. 1.5 QUALITY AASSURANCE A. Installer: Experienced in similar types of work of similar scope and be able to furnish list of previous jobs and references if requested by Architect. B. Expansion Joints: Provide expansion joints as indicated on Drawings or, if not indicated, install at frequency and in accordance with details and as recommended by manufacturer. Confirm locations and frequency with Architect before beginning work. C. Certifications 1. Provide written documentation that products have met or exceeded at least one of the following certifications for a minimum of 10 years. a. FHA-HUD 1.6 PROJECT CONDITIONS A. Environmental Requirements: 1. Minimum air temperature of 40 degrees F (4 degrees C) prior to, during, and for 48 hours after completion of work; and 2. Cold Weather Requirements: IMIAC (International Masonry Industry All-Weather Council) - Recommended Practices and Guide Specifications for Cold Weather Masonry Construction. 1.7 DELIVERY, STORAGE AND HANDLING A. Store mortar materials on pallets in dry place. B. Protect materials from rain, moisture, and freezing temperatures. C. Store manufactured thin brick/panel brick veneer above ground on level platforms, which allow air circulation under stacked units. D. Handle units on pallets or flat bed barrows. 1.8 WARRANTY A. Provide a 20-year warranty against manufacturing defects in manufactured thin brick/panel brick veneer products. PART 2 - PRODUCTS 2.1 DESIGN BASIS: A. Thin Brick as manufactured by Thin Brick by Owensboro Ewing Road, Owensboro, Kentucky 42301, (270) , (270) Thin Brick Style/Color to match existing brick units.

3 SUNY GENESEO B. Thin Brick/Thin Brick Veneer 1. Kiln fired thin brick, composed of following materials: a. TBS (Standard) and TBA brick. 2. Durability: ASTM C1088, Grade Exterior. 3. Freeze and Thawing: No breakage and not greater than 0.5% loss in dry weight when tested in accordance with ASTM C Thin brick veneer size: 7 ½ (L) inches by 2 ¼ (H) inches by ½ thick. C. Regional Materials: Credit MR5, Brick shall be manufactured within 500 miles of Project site from materials that have been extracted, harvested, or recovered, as well as manufactured, within 500 miles of Project site. 2.2 BRICK VENEER ACCESSORIES A. Adhesive: Interior, water base, non-flammable adhesive. 1. Manufacturer: Franklin International, 2020 Bruck Street, Columbus, Ohio 43207, (800) a. Or Approved Equal. B. Mortar: A rich mixture of the following materials, mixed in accordance with the manufacturers detailed installation instructions for tuck pointing thin brick veneer joints. 1. Regional Materials: Credit MR5, Aggregate for mortar and grout, cement, and lime shall be manufactured within 500 miles of Project site. 2. Portland Cement: ASTM C 150, Type I or II, except Type III may be used for coldweather construction. Provide natural color or white cement as required to produce mortar color indicated. 3. Hydrated Lime: ASTM C 207, Type S. 4. Aggregate for Mortar: ASTM C 144. a. For mortar that is exposed to view, use washed aggregate consisting of natural sand or crushed stone. b. White-Mortar Aggregates: Natural white sand or crushed white stone. c. Colored-Mortar Aggregates: Natural sand or crushed stone of color necessary to produce required mortar color. 5. Mortar Pigments: Natural and synthetic iron oxides and chromium oxides, compounded for use in mortar mixes. Use only pigments with a record of satisfactory performance in masonry mortar. 6. Water: Potable. 7. Thoroughly mix grout ingredients in quantities needed for immediate use. Mix grout to ASTM C 270, Type S proportions. C. Mortar Mixes: 1. Do not use admixtures, including pigments, air-entraining agents, accelerators, retarders, water-repellent agents, antifreeze compounds, or other admixtures, unless otherwise indicated. 2. Limit cementitious materials in mortar to portland cement and lime. 3. Pigmented Mortar: Use colored cement product or select and proportion pigments with other ingredients to produce color required. Do not add pigments to colored cement products.

4 SUNY GENESEO a. Pigments shall not exceed 10 percent of portland cement by weight. b. Mix to match color of existing. c. See Section Brick Masonry for additional information. D. Moisture Barrier: 1. Joint Sealant: Refer to Section Fasteners: Coated 1-1/2 inch nails, staples, or screws of type and for spacing as recommended by thin brick veneer manufacturer for loads encountered. 3. Cleaner: Nonacid cleaner as recommended by thin brick veneer manufacturer. PART 3 - EXECUTION 3.1 EXAMINATION AND PREPARATION A. Exanimation: 1. Verify that field conditions are acceptable and are ready to receive work in accordance with the manufacturers written installation instructions. 2. Verify that built-in items are in proper location and ready for roughing into masonry work. 3. Consult Architect if deficiencies exist. Correct deficiencies in accordance with requirements of thin brick veneer manufacturer s written installation instructions. B. Protect surrounding area from possible damage during installation work. C. Initiating installation constitutes Installer s acceptance of substrates. 3.2 INSTALLATION A. Thin Brick by Owensboro Pieces and Corners Unit Application: 1. Interior: Apply Interior/Exterior adhesive to the back of each thin brick veneer unit. a. Place thin brick pieces in position level, with 3/8 inch joint spacing, plumb with surrounding units. Apply firm pressure to bed the unit solidly in the adhesive base. 1) Bond Pattern: Running bond, or as indicated on the Drawings. 2) Install outside corner return units with short and long lengths alternated. 3) Plan work to minimize jobsite cutting. Perform necessary cutting with proper tools to provide uniform edges; take care to prevent breaking unit corners or edges. B. JOINTING 1. Allow adhesive to set and cure in accordance with the manufacturer s instructions for individual thin brick veneer units. 2. Install mortar to thin brick veneer joints using a tuck pointing tool, metal tipped mortar bag or a grout setting machine in accordance with the manufacturers written installation instructions. 3. Fill joints completely with mortar. a. Remove excess mortar; do not allow mortar to dry on face of units. b. Tool exposed joints slightly concave when thumbprint hard, using a jointer larger than joint thickness, unless otherwise indicated. c. Clean and finish joints in accordance with manufacturer s instructions. d. Control Joints: Size in accordance with Section for sealant performance, but in no case larger than adjacent mortar joints in exposed thin brick veneer units.

5 SUNY GENESEO Expansion Joints: Provide where indicated on Drawings or as recommended by system manufacturer. 5. Built-in Work: As work progresses, build in door and window frames, nailing strips, anchor bolts, plates, and other items specified in various sections. 6. Build in items plumb and level. a. Do not build in organic materials subject to deterioration. C. ADJUSTING 1. Cutting and Fitting: Cut and fit for chases, pipes, conduit, sleeves, and grounds. Cooperate with other sections of work to provide correct size, shape, and location. D. CLEANING AND SEALING 1. Remove excess mortar and smears using nylon brush. 2. Replace defective mortar. Match adjacent work. 3. Clean soiled surfaces with non-alcoholic solution, acceptable to the thin brick veneer manufacturer, which will not harm masonry or adjacent materials. 4. Leave surfaces thoroughly clean and free of mortar and other soiling. 5. Use non-metallic tools in cleaning operations. END OF SECTION

6

SECTION BRICK MASONRY ASSEMBLIES

SECTION BRICK MASONRY ASSEMBLIES PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Face brick. 2. Mortar and grout. 3. Ties and anchors. 4. Miscellaneous masonry accessories. 1.2 SUBMITTALS A. Product Data: For each type

More information

A. MASONRY MASONRY SECTION General Requirements: Division One is applicable in full hereto.

A. MASONRY MASONRY SECTION General Requirements: Division One is applicable in full hereto. PHJN1010CU SECTION 0400 MASONRY A. MASONRY 1. General Requirements: Division One is applicable in full hereto. 2. General: Workmanship shall be first class, with horizontal courses level, vertical joints

More information

SECTION GLASS UNIT MASONRY ASSEMBLIES

SECTION GLASS UNIT MASONRY ASSEMBLIES PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to install glass unit masonry as shown on the contract drawings and

More information

SECTION UNIT MASONRY ASSEMBLIES

SECTION UNIT MASONRY ASSEMBLIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Concrete masonry units. 2. Decorative masonry units. 3. Mortar and grout. 4. Steel reinforcing bars. 5. Masonry joint reinforcement. 6. Ties and anchors.

More information

SPECIFICATION GUIDELINE

SPECIFICATION GUIDELINE SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification

More information

Spec Master 5/7/ For each product requiring color and texture selection, provide full size samples.

Spec Master 5/7/ For each product requiring color and texture selection, provide full size samples. SECTION 04812 (042012) MECHANICALLY ATTACHED BRICK PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

PART 1 GENERAL MANUFACTURED STONE MASONRY

PART 1 GENERAL MANUFACTURED STONE MASONRY SECTION 04 73 00 (04730) PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Simulated Stone B. Products installed, but not furnished, under this Section include the following: 1. Steel Lintel and Shelf

More information

SPECIFICATION GUIDELINE

SPECIFICATION GUIDELINE Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section

More information

SECTION MANUFACTURED MASONRY VENEER

SECTION MANUFACTURED MASONRY VENEER TM Dutch Quality Stone 18012 Dover Road Mt. Eaton, OH 44659 Tel: (330) 359-7866 Fax: (330) 359-5990 e-mail: info@dutchqualitystone.com website: www.dutchqualitystone.com SECTION 04 73 00 MANUFACTURED MASONRY

More information

Thin Architectural Splitface Block Veneer Specification Guide

Thin Architectural Splitface Block Veneer Specification Guide Thin Architectural Splitface Veneer System with AccuTab Technology R Thin Architectural Splitface Block Veneer Specification Guide Section 04711: Manufactured Concrete Veneer Use this specification guide

More information

DURRELL DESIGN GROUP, PLLC ROOF REPLACEMENT BARR ELEMENTARY SCHOOL JACKSON PUBLIC SCHOOL DISTRICT JACKSON, MISSISSIPPI.

DURRELL DESIGN GROUP, PLLC ROOF REPLACEMENT BARR ELEMENTARY SCHOOL JACKSON PUBLIC SCHOOL DISTRICT JACKSON, MISSISSIPPI. DURRELL DESIGN GROUP, PLLC 500-G E. WOODROW WILSON AVENUE JACKSON, MISSISSIPPI 39216 PHONE: 601.708.4788 FAX: 601.488.4717 ROOF REPLACEMENT BARR ELEMENTARY SCHOOL JACKSON PUBLIC SCHOOL DISTRICT JACKSON,

More information

SECTION MANUFACTURED MASONRY

SECTION MANUFACTURED MASONRY SECTION 047000 MANUFACTURED MASONRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

A. ASTM C190 - Test Method for Tensile Strength of Hydraulic Cement Mortars

A. ASTM C190 - Test Method for Tensile Strength of Hydraulic Cement Mortars SECTION 04850 (04 40 00) MSI PRECAST STONE VENEER SYSTEM PART 1 GENERAL 1.1 SECTION INCLUDES A. MSI Precast Stone Veneer for exterior and interior vertical surfaces. 1.2 RELATED SECTIONS Specifier Notes:

More information

SECTION MORTAR

SECTION MORTAR PART l - SCOPE SECTION 04100 - MORTAR A. This Section includes all labor, materials, equipment, and related items required for the work of mortar as shown on the Drawings and specified herein. The work

More information

Product Guide Specification

Product Guide Specification Product Guide Specification SECTION 04850 (04 40 00) NATURAL THIN VENEER STONE PART 1 GENERAL 1.1 SECTION INCLUDES Specifier Notes: Edit the following as required. A. Natural thin veneer stone for [exterior]

More information

SECTION Vitrified Clay Wall Coping 2014

SECTION Vitrified Clay Wall Coping 2014 SECTION 04220 2014 PART 1 GENERAL 1.1 DESCRIPTION A. SCOPE OF WORK 1. Provide new coping as indicated on Drawings. B. RELATED SECTIONS 1. Section 02050: Selective Demolition. 2. Section 07650: Metal Flashing.

More information

A. Section includes historic treatment work consisting of rep ointing brick masonry as follows:

A. Section includes historic treatment work consisting of rep ointing brick masonry as follows: SECTION 040323 - HISTORJC BRlCK UNIT MASONRY REPOINTING PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars.

SECTION CEMENT BOARD SUPPORTED ADHERED MASONRY VENEER. 2. Installation materials including adhesives, mortars, and pointing mortars. (Specifier Note: The purpose of this guide specification is to assist the Specifier in correctly specifying cement board supported adhered masonry. The Specifier needs to edit these guide specifications

More information

SECTION CAST STONE MASONRY

SECTION CAST STONE MASONRY SECTION 047200 - CAST STONE MASONRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

SECTION MANUFACTURED STONE VENEER. A. Section Includes: 1. Manufactured stone veneer masonry, accessories, and related materials.

SECTION MANUFACTURED STONE VENEER. A. Section Includes: 1. Manufactured stone veneer masonry, accessories, and related materials. SECTION 04 70 00 MANUFACTURED STONE VENEER PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Manufactured stone veneer masonry, accessories, and related materials. 1.2 SUBMITTALS A. Product Data: For

More information

Native Custom Stone Guide Specification 1/30/2012 SECTION MANUFACTURED STONE VENEER

Native Custom Stone Guide Specification 1/30/2012 SECTION MANUFACTURED STONE VENEER 1/30/2012 SECTION 04 70 00 MANUFACTURED STONE VENEER PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Manufactured stone veneer masonry, accessories, and related materials. 1.2 SUBMITTALS A. Product

More information

SECTION SANDSTONE RESTORATION

SECTION SANDSTONE RESTORATION SECTION 04 01 40.91 - SANDSTONE RESTORATION Part 1 GENERAL 1.1 SUMMARY OF WORK A. For repairing and patching of sandstone. B. Related Sections 1. Section 01351 Special Procedures for Historic Treatment

More information

RENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11

RENOVATE BUILDING 18-C FTFA SECTION GYPSUM BOARD 05/11 SECTION 09 29 00 GYPSUM BOARD 05/11 PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text

More information

HammerStone Manufactured stone veneers for commercial & residential applications

HammerStone Manufactured stone veneers for commercial & residential applications HammerStone Manufactured stone veneers for commercial & residential applications Veneer Stone Specification Guide Section 04711: Manufactured Stone Veneer Use this specification guide for each individual

More information

1. Repairing brick masonry, including replacing damaged units as indicated on drawings. 2. Repointing mortar joints.

1. Repairing brick masonry, including replacing damaged units as indicated on drawings. 2. Repointing mortar joints. SECTION 040120 BRICK MASONRY REPAIR AND REPOINTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

SECTION (04730) - MANUFACTURED STONE MASONRY

SECTION (04730) - MANUFACTURED STONE MASONRY 1.01 SUMMARY SECTION 04 73 00 (04730) - MANUFACTURED STONE MASONRY A. Section Includes: 1. Cast Stone Standard Units, Chamfer Units and Custom stone trim, minimum 3 ¾ thick, layed up with brick masonry

More information

CUT LIMESTONE - ANCHORED

CUT LIMESTONE - ANCHORED SECTION 04851 CUT LIMESTONE - ANCHORED This guide specification has been prepared by TexaStone Quarries LLC to assist design professionals in the preparation of a specification section covering cut limestone,

More information

MANUFACTURER S SPECIFICATIONS Section LIMESTONE PLASTER

MANUFACTURER S SPECIFICATIONS Section LIMESTONE PLASTER MANUFACTURER S SPECIFICATIONS Section 09220 LIMESTONE PLASTER LE DÉCOR LIMESTONE PART 1 GENERAL 1.1 General A. This section describes the requirements for furnishing and installing Limestone Plaster. 1.2

More information

MANUFACTURER S SPECIFICATION

MANUFACTURER S SPECIFICATION MANUFACTURER S SPECIFICATION Eldorado Stone Corporation PO Box 489 Carnation, WA 98014 Tel: (800) 925-1491 Fax: (425) 333-4755 e-mail: general@eldoradostone.com website: www.eldoradostone.com SECTION 04730

More information

GUIDE SPEC SECTION Injection Grout (IG10)

GUIDE SPEC SECTION Injection Grout (IG10) Part 1 GENERAL MASONRY UNIT RESTORATION 1.1 SUMMARY OF WORK A. For repairing, patching, injecting cracks and re-attaching stone fragments to original substrate. B. Related Sections 1. Section 01351 Special

More information

Stonecraft Industies 8300 County Road Holmesville, OH

Stonecraft Industies 8300 County Road Holmesville, OH Stonecraft Industies 8300 County Road Holmesville, OH Tel: (888) 580-6448 e-mail: customercare@stonecraft.com website: www.stonecraft.com SECTION 04 73 00 MANUFACTURED MASONRY VENEER GENERAL NOTES TO SPECIFIER:

More information

SECTION UNIT MASONRY

SECTION UNIT MASONRY SECTION 04200 UNIT MASONRY A. ACCEPTABLE MANUFACTURERS 1. Sound Absorptive Masonry Units: 12 inch wide Soundblox type RSC/RF as manufactured by the Proudfoot Company, Monroe, CT. 2. Concrete Masonry Units:

More information

SECTION INSTALLATION AND/OR REPLACEMENT OF MASONRY UNITS AND REPOINTING

SECTION INSTALLATION AND/OR REPLACEMENT OF MASONRY UNITS AND REPOINTING SECTION 04210 INSTALLATION AND/OR REPLACEMENT OF MASONRY UNITS AND REPOINTING PART I GENERAL 1.1 SUMMARY A. Provide installation of new or replacement of masonry units and/or repointing of masonry units

More information

MANUFACTURER S SPECIFICATIONS Section ST. ASTIER LIME PLASTER (NHL) MASONRY [BLOCKS] [BRICKS] [STONE]

MANUFACTURER S SPECIFICATIONS Section ST. ASTIER LIME PLASTER (NHL) MASONRY [BLOCKS] [BRICKS] [STONE] MANUFACTURER S SPECIFICATIONS Section 09225 ST. ASTIER LIME PLASTER (NHL) MASONRY [BLOCKS] [BRICKS] [STONE] ST. ASTIER NATURAL HYDRAULIC LIME PLASTER PART 1 GENERAL 1.1 Summary A. This Section includes

More information

SECTION CONCRETE UNIT MASONRY

SECTION CONCRETE UNIT MASONRY SECTION 042200 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

Multi-Institutional Academic Health Science & Research Center Evansville, IN

Multi-Institutional Academic Health Science & Research Center Evansville, IN SECTION 061600 - SHEATHING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

DIVISION 04 MASONRY CAST STONE. A. Design Considerations. 1. Cast stone shall comply with ASTM C1364, Standard Specification for Cast Stone.

DIVISION 04 MASONRY CAST STONE. A. Design Considerations. 1. Cast stone shall comply with ASTM C1364, Standard Specification for Cast Stone. DIVISION 04 MASONRY 04720 CAST STONE A. Design Considerations 1. Cast stone shall comply with ASTM C1364, Standard Specification for Cast Stone. 2. Care must be taken in the design of individual units

More information

SECTION Arisfor WallGuard

SECTION Arisfor WallGuard 1.1 GENERAL A. is a three component polymerized cementitious protective coating that can be applied to a variety of vertical interior and exterior substrates including: stucco, exterior gypsum sheathing,

More information

DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION MORTAR AND MASONRY GROUT

DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION MORTAR AND MASONRY GROUT SECTION 04110 MORTAR AND MASONRY GROUT PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. In the absence of other information, the methods and recommendations of the National Concrete Masonry Association

More information

B. Samples: Submit, for verification purposes, samples of the following:

B. Samples: Submit, for verification purposes, samples of the following: SECTION 04500 - MASONRY RESTORATION AND CLEANING PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings, photos and general provisions of Contract, including General and Supplementary Conditions and Division-1

More information

INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES

INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES EVALUATION CRITERIA FOR ANCHORED MASONRY VENEER SYSTEM WITH POLYSTYRENE FOAM PLASTIC BACKING EC 021-2014 (Adopted

More information

SECTION BRICK FLOORING

SECTION BRICK FLOORING SECTION 09 63 13 BRICK FLOORING SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brick flooring

More information

MANUFACTURER'S SPECIFICATIONS Section ST. ASTIER LIME PLASTER (NHL) PLASTER ON CONCRETE

MANUFACTURER'S SPECIFICATIONS Section ST. ASTIER LIME PLASTER (NHL) PLASTER ON CONCRETE MANUFACTURER'S SPECIFICATIONS Section 09225 ST. ASTIER LIME PLASTER (NHL) PLASTER ON CONCRETE ST. ASTIER NATURAL HYDRAULIC LIME PLASTER PART 1 GENERAL 1.1 Summary A. This Section includes St. Astier Natural

More information

SECTION UNIT MASONRY

SECTION UNIT MASONRY SECTION 04200 UNIT MASONRY PART 1 GENERAL 1.01 SUMMARY A. Furnish labor, materials, and equipment and perform functions required in the installation and maintenance of the work covered by this Section.

More information

Student Services & Classroom Addition

Student Services & Classroom Addition SECTION 093000 - TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

SECTION Fiber Reinforced Stucco 1

SECTION Fiber Reinforced Stucco 1 CSI SECTION 09200 FIBER REINFORCED STUCCO PART 1 GENERAL 1.01 SUMMARY A. Section Description: Provided lath and plaster where shown on the Drawings, as specified herein, and as needed for complete and

More information

EDGEWATER, FLORIDA JUNE 14, 2010

EDGEWATER, FLORIDA JUNE 14, 2010 SECTION 09 2400 - PORTLAND CEMENT PLASTER PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION UNIT MASONRY SYSTEM

SECTION UNIT MASONRY SYSTEM SECTION 04320 UNIT MASONRY SYSTEM PART 1 GENERAL 1.01 SECTION INCLUDES A. Concrete masonry and face brick units. B. Reinforcement, anchorage, and accessories. 1.03 SUBMITTALS A. Submit product data under

More information

OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. RobinsonBrick.com

OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide. RobinsonBrick.com OLD BRICK ORIGINALS KILN-FIRED THIN BRICK VENEER Installation Guide RobinsonBrick.com OLD BRICK ORIGINALS THIN BRICK VENEER Page 2 INTRODUCTION Check local building codes for proper installation guidelines

More information

Paragraph Description Page No General Materials Concrete Masonry Work Altitude Valve Vault Cover 25-4

Paragraph Description Page No General Materials Concrete Masonry Work Altitude Valve Vault Cover 25-4 City of Columbia Engineering Regulations PART 25: SPECIFICATIONS FOR ALTITUDE VALVE VAULT Table of Contents Paragraph Description Page No. 25.1 General 25-1 25.2 Materials 25-1 25.3 Concrete Masonry Work

More information

B. Related Sections include: 1. Division 2, Section , Miscellaneous Cast-in-Place Concrete 2. Division 9, Section , Stone Paving

B. Related Sections include: 1. Division 2, Section , Miscellaneous Cast-in-Place Concrete 2. Division 9, Section , Stone Paving SECTION 04 43 00 - STONE VENEER WALLS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following applications: 1. Stone Veneer on Cast-in-Place Concrete retaining walls, 2. Stone Veneer on CMU

More information

SECTION STRUCTURAL INSULATED PANELS

SECTION STRUCTURAL INSULATED PANELS SECTION 06120 STRUCTURAL INSULATED PANELS Copyright 2011-2012 Korwall Industries, Inc. - All rights reserved PART 1 GENERAL 1.1 SECTION INCLUDES A. Structural Insulated Roof Panels. B. Structural Insulated

More information

The Admixture Systems business of BASF Corporation previously conducted business as Degussa Admixtures, Inc. and Master Builders, Inc.

The Admixture Systems business of BASF Corporation previously conducted business as Degussa Admixtures, Inc. and Master Builders, Inc. Note to Specifier: The Admixture Systems business of BASF Corporation previously conducted business as Degussa Admixtures, Inc. and Master Builders, Inc. BASF has launched the Master Builders Solutions

More information

CTIOA REPORT

CTIOA REPORT CERAMIC TILE INSTITUTE OF AMERICA, INC. 12061 Jefferson Blvd., Culver City, CA 90230-6219 CTIOA REPORT 2002-4-25 SUBJECT: Direct Bond Thin Set Method Glass Mosaic Tile Over Exterior and Interior Portland

More information

DIVISION 4 MASONRY DIVISION 4 - MASONRY

DIVISION 4 MASONRY DIVISION 4 - MASONRY DIVISION 4 MASONRY DIVISION 4 - MASONRY 85 SECTION 04000 - MASONRY 04000 - MASONRY PART 1 - GENERAL 1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

SECTION NEW WOOD WINDOWS. 1. Section Wood Window Restoration. 2. Section Painting.

SECTION NEW WOOD WINDOWS. 1. Section Wood Window Restoration. 2. Section Painting. SECTION 08610 NEW WOOD WINDOWS PART 1 - GENERAL 1.1 SUMMARY A. Provide new wood double hung, casement and awning windows and frames, complete, as shown and specified. 1. The new windows and frames shall

More information

SECTION PORTLAND CEMENT PLASTERING

SECTION PORTLAND CEMENT PLASTERING SECTION 09 2400 PORTLAND CEMENT PLASTERING This section includes editing notes to assist the user in editing the section to suit project requirements. These notes are included as hidden text, and can be

More information

SECTION STONE FLOORING

SECTION STONE FLOORING PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 09 63 40 STONE FLOORING SPEC WRITER NOTE: Delete // // if not applicable to project. Also delete any other item or paragraph not applicable in the section and

More information

SECTION ARCHITECTURAL CONCRETE UNIT MASONRY

SECTION ARCHITECTURAL CONCRETE UNIT MASONRY SECTION 04 2223 PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Split-face concrete unit masonry, burnished concrete unit masonry, and polished concrete unit masonry. 2. Split-face concrete unit masonry.

More information

SECTION CEMENTITIOUS SHEATHING

SECTION CEMENTITIOUS SHEATHING SECTION 06 16 63 CEMENTITIOUS SHEATHING SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Use this Section for exterior sheathing as a backup

More information

SECTION Specification for Building Limes Specification For Building Sands from Natural Sources Methods of Tests for Paints.

SECTION Specification for Building Limes Specification For Building Sands from Natural Sources Methods of Tests for Paints. SECTION 09200 PART 1 - GENERAL 1.01 DESCRIPTION A. Extent of Work: The extent of lath and plaster work is shown on the drawings and in schedules and includes interior and exterior plaster work, and fibreglass

More information

SECTION (Master Format, 1995 Edition, 04700) MANUFACTURED MASONRY

SECTION (Master Format, 1995 Edition, 04700) MANUFACTURED MASONRY SECTION 04 70 00 (Master Format, 1995 Edition, 04700) MANUFACTURED MASONRY PART I - GENERAL 1.01 SUMMARY A. Section Includes: Manufactured Stone Veneer, Manufactured Stone Trim, and Application Materials.

More information

Façade Architectural Wall Panel System - Guide Specification 3/11/2017 SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.

Façade Architectural Wall Panel System - Guide Specification 3/11/2017 SECTION FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1. SECTION 09 7710 FRAMED DECORATIVE PANEL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: Decorative ½ / ¾ (13mm/19mm) thick prefinished panel with preengineered attachment clip along with hardware

More information

Installation Guide Wall Panels

Installation Guide Wall Panels Installation Guide Wall Panels Jointless or Dry-Stacked Installation (Read Prior to installation) The MStone system is a jointless / dry-stacked installation where panels and corners fit tightly together

More information

In the design development phase, submit finish and material selections to Facilities Management Planning Group for review.

In the design development phase, submit finish and material selections to Facilities Management Planning Group for review. 09 00 00 FINISHES 09 01 00 Maintenance of Finishes 09 01 20 Maintenance of Plaster and Gypsum Board 09 01 20.91 Plaster Restoration 09 01 30 Maintenance of Tiling 09 01 30.91 Tile Restoration 09 01 50

More information

ALUMABOARD SECTION ALUMINUM SIDING AND SOFFITS. A. Section Cold-Formed Metal Framing: Metal framing for support of aluminum soffits.

ALUMABOARD SECTION ALUMINUM SIDING AND SOFFITS. A. Section Cold-Formed Metal Framing: Metal framing for support of aluminum soffits. ALUMABOARD SECTION 07 46 00 ALUMINUM SIDING AND SOFFITS PART 1 GENERAL 1.2 RELATED SECTIONS 1.3 REFERENCES A. SECTION INCLUDES B. Aluminum Siding. C. Aluminum Soffits. D. Aluminum trim and accessories.

More information

by Rollfab Metal Products

by Rollfab Metal Products by Rollfab Metal Products SECTION 07460 ALUMINUM SIDING AND SOFFITS PART 1 GENERAL 1.2 RELATED SECTIONS 1.3 REFERENCES A. SECTION INCLUDES B. Aluminum Siding. C. Aluminum Soffits. D. Aluminum trim and

More information

BYU CITY FIRE STATION

BYU CITY FIRE STATION SECTION 04810 - UNIT MASONRY ASSEMBLIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification

More information

SECTION NATURAL STONE VENEER

SECTION NATURAL STONE VENEER CSI 3-PART SPEC Eldorado Stone 1370 Grand Ave., Bldg. B San Marcos, CA 92069 tel: (800) 925-1491 fax: (760) 736-8890 e-mail: contactus@eldoradonatural.com website: www.eldoradonatural.com SECTION 04 43

More information

SECTION CERAMIC TILE. B. Ceramic tile wall finishes including standard and custom designs.

SECTION CERAMIC TILE. B. Ceramic tile wall finishes including standard and custom designs. SECTION 09 30 13 CERAMIC TILE PART 1 GENERAL 1.1 SECTION INCLUDES A. Ceramic tile floor and base finishes. B. Ceramic tile wall finishes including standard and custom designs. 1.2 REFERENCES A. ANSI/TCNA

More information

Architects - Stone Guide Specifications

Architects - Stone Guide Specifications Architects - Stone Guide Specifications SECTION 04 73 01 MANUFACTURED STONE PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Manufactured stone masonry, accessories, and related materials. 1.2 SUBMITTALS

More information

SECTION MANUFACTURED MASONRY VENEER

SECTION MANUFACTURED MASONRY VENEER CSI 3 PART SPEC Eldorado Stone, LLC 1370 Grand Ave., Bldg., B San Marcos, CA 92069 Tel: (760) 736-3232 Fax: (760) 736-8890 e-mail: customerservice@eldoradostone.com website: www.eldoradostone.com SECTION

More information

REINFORCED CONCRETE MASONRY SECTION

REINFORCED CONCRETE MASONRY SECTION SECTION 04 22 02 - REINFORCED CONCRETE MASONRY PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 01 Specification

More information

TerraClad TM General Specifications

TerraClad TM General Specifications TerraClad TM General Specifications PRODUCT NAMES: Terra cotta Baguettes/Louvers and Related Work MANUFACTURER: Boston Valley Terra Cotta 6860 S. Abbott Road Orchard Park, NY 14127 Phone: 888-214-3655

More information

Highland Manor Dr Suite Website:

Highland Manor Dr Suite Website: MAGNUM BOARD PRODUCTS Interior Exterior Sheathing Ceiling Board - Backer/Underlayment - Trim Siding Materials Specification 120209-1400, Issue 5 PART 1 GENERAL 1.1 SECTION INCLUDES A. Magnum wall board

More information

Maintenance of Unit Masonry

Maintenance of Unit Masonry University of New Hampshire University of New Hampshire Scholars' Repository Division 04 Masonry Chapter 5 Technical Construction and Renovation Standards 1-25-2013 040120 - Maintenance of Unit Masonry

More information

SECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board

SECTION GYPSUM WALLBOARD SYSTEMS. A. Gypsum board at new wall partitions or where indicated on drawings. B. ASTM C442 - Gypsum Backing Board SECTION 09260 GYPSUM WALLBOARD SYSTEMS PART 1 - GENERAL 1.1 SECTION INCLUDES A. Gypsum board at new wall partitions or where indicated on drawings. 1.2 REFERENCED STANDARDS A. ASTM C36 - Gypsum Wallboard

More information

SECTION UNIT PAVERS

SECTION UNIT PAVERS PART 1 - GENERAL 1.1 SUMMARY A. Section includes the following: 1. Concrete pavers. 2. Detectable warning pavers. 3. Warning stripe pavers. 1.2 SUBMITTALS A. Product Data: For the following: 1. Pavers.

More information

SECTION TILING

SECTION TILING PART 1 GENERAL 1.01 SECTION INCLUDES A. Ceramic Tile for floor applications. B. Ceramic Tile for wall applications. C. Ceramic accessories. D. Ceramic trim. E. Non-ceramic trim. 1.02 RELATED REQUIREMENTS

More information

SECTION LATEX-MODIFIED MEDIUM BED MORTAR

SECTION LATEX-MODIFIED MEDIUM BED MORTAR SECTION 09305.24 LATEX-MODIFIED MEDIUM BED MORTAR This product guide specification can be used to specify Hydroment Big Tile & Stone Mortar, a latex-modified, medium bed mortar designed for setting large

More information

XTREME-BOND INSTALLATION SYSTEM

XTREME-BOND INSTALLATION SYSTEM XTREME-BOND FOR THIN-STONE VENEER Weather-resistant resistant Superior bonding & flexural strengths Exceptional sag resistance Meets requirements of Type S mortar Pre-blended for quality consistency from

More information

This Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces:

This Section includes surface preparation and field application of anti-graffiti coating systems for the following vertical and horizontal surfaces: 0 0 0 0 0 0 SECTION 0 ANTI- GRAFFITI COATINGS PART - GENERAL RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division Specification

More information

SECTION TILING

SECTION TILING SECTION 093000 TILING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

SECTION ARCHITECTURAL PRECAST CONCRETE. C. Section Joint Sealers: Perimeter joints with sealant and backing.

SECTION ARCHITECTURAL PRECAST CONCRETE. C. Section Joint Sealers: Perimeter joints with sealant and backing. SECTION 03451 ARCHITECTURAL PRECAST CONCRETE PART 1 GENERAL 1.01 SECTION INCLUDES A. Architectural precast concrete wall panels; with integral insulation. B. Supports, anchors, and attachments. C. Intermediate

More information

B. Related Sections: 1. Division 07 Section "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.

B. Related Sections: 1. Division 07 Section Joint Sealants for sealing of expansion, contraction, control, and isolation joints in tile surfaces. SECTION 093000 - CERAMIC TILE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Hardscaping Installation Manual

Hardscaping Installation Manual Hardscaping Installation Manual INDEX Installation of Pavers... 1 Installation of Meshed Flagstone... 2 Installation of Veneer Stone... 3 Sand Set Installation of Pavers 1. Preparing the ground Mark your

More information

SECTION FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES

SECTION FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES SECTION 081613 FIBERGLASS REINFORCED POLYESTER (FRP) DOORS AND ALUMINUM FRAMES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary

More information

CSI SECTION Adhered Masonry Veneer Systems - Exterior Facade Ceramic Tiling - Exterior facade

CSI SECTION Adhered Masonry Veneer Systems - Exterior Facade Ceramic Tiling - Exterior facade CSI SECTION 04 05 13 Adhered Masonry Veneer Systems - Exterior Facade 09 30 13 Ceramic Tiling - Exterior facade SPECIFICATION OVERVIEW (This overview is not part of the specification) Parex USA offers

More information

SECTION GYPSUM BOARD & SHEATHING SYSTEMS

SECTION GYPSUM BOARD & SHEATHING SYSTEMS PART 1!GENERAL! 1.01! SECTION INCLUDES SECTION 09260 GYPSUM BOARD & SHEATHING SYSTEMS! Metal stud wall framing. Metal channel ceiling framing.! Gypsum board.! Sheathing.! Taped and sanded joint treatment.!

More information

GENERAL SHALE NATURAL THIN ROCK VENEER Installation Guide. GeneralShale.com

GENERAL SHALE NATURAL THIN ROCK VENEER Installation Guide. GeneralShale.com GENERAL SHALE NATURAL THIN ROCK VENEER Installation Guide GeneralShale.com GENERAL SHALE NATURAL THIN ROCK VENEER Page 2 INTRODUCTION - TABLE OF CONTENTS Check local building codes for proper installation

More information

MOUNTAIN STONE Products

MOUNTAIN STONE Products MOUNTAIN STONE Products PRODUCT USERS GUIDE Mountain Stone Products P.O. Box 20308 42102 4301 Industrial Road Bowling Green, KY. 42101 (270) 796-6123 (270) 796-6131 (800) 781-0277 Local Fax Nationwide

More information

for Mortar-Set Concrete Tiling Installations

for Mortar-Set Concrete Tiling Installations The following specification refers to the Stepstone, Inc. product known as: Large Scale CalArc Pavers for Mortar-Set Concrete Tiling Installations Large Scale CalArc Pavers are part of the California Architectural

More information

SECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION

SECTION SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION SECTION 093000 - SHEET MEMBRANE WATERPROOFING AND CRACK ISOLATION PART 1 - GENERAL This specification includes the sheet membrane used as waterproofing, vapor retarder, and crack isolation in conjunction

More information

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS

SECTION EXTERIOR INSULATION AND FINISH SYSTEMS SECTION 07 24 00 EXTERIOR INSULATION AND FINISH SYSTEMS PART 1 GENERAL 1.1 REFERENCES The publications listed below form a part of this specification to the extent referenced. The publications are referred

More information

A. Section includes fluid applied, vapor permeable membrane air barriers.

A. Section includes fluid applied, vapor permeable membrane air barriers. Master Construction Specifications Insert Project Name SECTION 072726 FLUID APPLIED MEMBRANE AIR BARRIERS PART 1 GENERAL 1.1 SUMMARY A. Section includes fluid applied, vapor permeable membrane air barriers.

More information

GYPSUM BOARD AND PLASTER

GYPSUM BOARD AND PLASTER CHAPTER 25 SECTION 2501 GENERAL 2501.1 Scope. 2501.1.1 General. Provisions of this chapter shall govern the materials, design, construction and quality of gypsum board, lath, gypsum plaster and cement

More information

CSI GUIDE Countertops

CSI GUIDE Countertops CSI GUIDE Countertops Part 1 General 1.0 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including general and supplementary conditions and Division 1 Specification Sections, apply

More information

CONCRETE TILE PAVERS

CONCRETE TILE PAVERS Section 32 14 13 CONCRETE TILE PAVERS (1995 MasterFormat Section 02780) Note: This guide specification for the U.S. is for the installation of concrete tile paving units whose thickness are less than the

More information

SECTION CONCRETE PAVING SLABS SET IN MORTAR

SECTION CONCRETE PAVING SLABS SET IN MORTAR SECTION 32 14 13.16 CONCRETE PAVING SLABS SET IN MORTAR (1995 MasterFormat Section 02784) Note: This guide specification for the U.S. is for paving slabs mortared to a concrete base and grouted joints

More information

Corium Brick Rainscreen System Specifications

Corium Brick Rainscreen System Specifications CORIUM BRICK RAINSCREEN SYSTEM PART 1 - GENERAL 1.1 SUMMARY A. Work Included: The Work of this Section shall include but not be limited to the following: 1. Corium brick plates 2. Galvanized and coated

More information