Manufacturers and suppliers of quality coating systems and associated materials to the Floor Covering and Building Industries

Size: px
Start display at page:

Download "Manufacturers and suppliers of quality coating systems and associated materials to the Floor Covering and Building Industries"

Transcription

1 to the Floor Covering and Building Industries FACT SHEET no.1 SUBSTRATE INSPECTION: Inspect the substrate thoroughly for any evidence of contamination that could jeopardise the integrity of the new DURON coating system. What to look for; moisture is one of the biggest causes of coating failures, new concrete, masonry floors and walls must be more than 3 months old and have a moisture content no higher than 5.5%. Evidence of moisture ingression could present in a white or dark colouring, this could be efflorescence; salt and other minerals being purged out from moisture migrating through the substrate. Ensure there are no existing coatings or contaminants that will need to be removed prior to the new coatings being applied; these could be paint, sealers, curing additives, oil or grease etc. All will affect the integrity of the new DURON coating system. The substrate itself needs to be a good sound surface, solid and free of soft, crumbly or unstable consistencies. If unsure of any of the above please Contact your supplier for further information. inadequate mixing, poor application techniques, non-compliance with curing times, improper thinning of coatings or any other variable beyond our control. No liability will be accepted Duron Pty Ltd 4 Progress Street Yatala Qld Ph: (07) Fax: (07) sales@duron.com.au

2 FACT SHEET no.2 SUBSTRATE PREPARATION: Fill all cracks and holes with a recommended filler, patching or levelling compound/resin. Internal floors may be subject to the Australian standards for an even surface, which requires the subfloor to have a tolerance no greater than + or - 3mm over a 3m straight edge. Prepare the floor by sanding or light grinding to smooth off and open the surface of concrete. Contact the technical department of your supplier for recommended products. For greasy, dirty garage floors clean with a recommended detergent, stiff broom and high pressure water-blaster. Acid etching should only be done if grinding equipment cannot be sourced. High pressure-clean immediately thereafter to remove any residue from the acid. Before proceeding to the next phase, ensure that the substrate is completely dry. The best way to check is with a Concrete Moisture Meter with a reading under 5.5% or to tape a small plastic patch on the floor, leave for 24 hours, if the underside shows signs of moisture, it is still too wet. The concrete surface should now be smooth, dry, oil and dust free with the surface sound. All surrounding edges and areas should be masking taped off for a clean finish. For any further information please contact your supplier. Duron Pty Ltd 4 Progress Street Yatala Qld Ph: (07) Fax: (07) sales@duron.com.au

3 FACT SHEET no. 3 DURON PRIMER/SEALER WATER-BASED EPOXY: Mixing: Please ensure DURON primer/sealer being a 2-part mix is mixed thoroughly with a low speed drill or mixer and stirrer, being careful not to aerate. Mix for at least 2 minutes until consistent viscosity is achieved. Mixing Ratio: 50% Part A to 50% Part B. (Refer to TDS Duron Primer/sealer) Ensure that everything is ready. Once the product has been mixed you only have a limited time to apply it before the product starts to harden, usually about 35 to 45 minutes working time only. Application: You can now begin to apply DURON primer/sealer to the surface, using a 10mm nap roller cover and paint brush for edges. Coverage Rate: Usually 1 litre of the mixed epoxy primer/sealer will be enough to cover approximately 8m2 dependent on porosity of substrate. Note: Allow DURON primer/sealer minimum 2-4hrs drying time before next stage of applying DURON basecoat and DURON acrylic flake.

4 DURON SEAMLESS COATINGS SYSTEMS FACT SHEET no. 4 DURON BASECOAT B WATER-BASED EPOXY: Mixing: Please ensure DURON basecoat being a 2-part mix is mixed thoroughly with a low speed drill or mixer and stirrer, being careful not to aerate. Mix for at least 2 minutes until consistent viscosity is achieved. Mixing Ratio: 50% Part A to 50% Part B (Refer to TDS) ensure that everything is ready. Once the product has been mixed you only have a limited time to apply it before the product starts to harden, usually about 35 to 45 minutes working time only. Coverage Rate: Approximately 1 litre of epoxy is enough to cover 5m2. Application: Apply basecoat with a 10mm nap roller cover and paint brush for edges. Note: This is the main coating that you will be broadcasting the DURON acrylic flake into, so ensure the product is wet enough to allow the DURON acrylic flake to stick. Always leave a wet line between you and the already cast flake area of approximately 200mm. We suggest mixing only a small amount of base coat epoxy at a time (e.g. 4 litre mixes). Please refer to technical data sheets for pot life and drying times as they depend on ambient temperatures

5 FACT SHEET no. 5 DURON DECORATIVE COLOUR FLAKE APPLICATION: The Epoxy is cut in with a brush around the edges, and rolled out on the floor in recommended 2 to 3 m2 sections at a time, broadcasting flake as you go. Starting from the back wall, lean over the wet epoxy and hand broadcast the flake in an upward and forward direction. Walk sideways and cast the flake until the basecoat has no visible patches of base colour, approximate coverage of flake: Standard 3.75m2 per kilo, Stone Grip 2m2 per kilo and Classic XL 5m2 per kilo if a full coverage is the desired look. Ensure you always leave a wet line between you and the already cast flake area. Proceed with the next section and repeat until finished. Ver.4

6 FACT SHEET no.6 DURON POLYURETHANE UV STABLE GLOSS (OPTION): Ensure the basecoat and flake surface is completely dry (approximately 6-8 hours). Scrape dry Flake with a Floor Scraper (for Stone Grip use a stiff broom) in a northsouth and east-west direction to dislodge all unsecured flake, vacuum thoroughly to remove all excess loose flake. The floor is now ready for the 1st coat of DURON UV Stable Gloss Polyurethane. Application (1 st Coat): Apply 1st coat of polyurethane with a 10mm nap micro fibre roller cover and brush for edges, at a coverage Rate: 1 Litre to cover 3-4 m2 for the first coat, ensuring an even saturation with no puddles, allow to dry for 6-8 hours. Application (2 nd coat): Light sand to take of any sharp edges, vacuum and apply second coat of polyurethane with a 10mm nap micro fibre roller cover and brush for edges at a coverage rate: 1 Litre to cover 7-8 m2 for the second coat ensuring an even saturation with no puddles. Duron Pty Ltd 4 Progress Street YATALA Ph: (07) Fax: (07) sales@duron.com.au Version 2.0

7 FACT SHEET No. (6) a DURON POLYASPARTIC UV STABLE GLOSS (OPTION): Ensure the basecoat and flake surface is completely dry (approximately 6-8 hours). Scrape dry Flake with a Floor Scraper (for Stonegrip use a stiff broom) in a north-south and east-west direction to dislodge all unsecured flake, vacuum thoroughly to remove all loose excess flake. The floor is now ready for the top coat of Duron Polyaspartic. Application (Topc ( Topcoat): oat): Apply coating of Duron Polyaspartic with a 10mm nap micro fibre roller cover and brush all edges, at a coverage Rate: 1 Litre to cover 5m2 for this coat, (mixing ratio: 1L A to 1L B) ensuring an even saturation with no puddles, allow to cure approximately 3-4 hours. inadequate mixing, poor application techniques, noncompliance with curing times, improper thinning of coatings or any other variable beyond our control. No liability will be accepted by Duron Pty Ltd, our employees, distributors, representatives or agents, for any loss or damage, direct or indirect that may result from the use of information and/or suggestions as actual conditions for use that are beyond our control. All materials should be checked and tested for their suitability for prevailing conditions on all individual sites. Version 1.0

8 to the Floor Covering and Building Industries FACT SHEET no. (7) DOMESTIC care/maintenance CARE AND MAINTENANCE OF YOUR NEWLY COMPLETED SEAMLESS FLOOR: Duron recommend a minimum of 24 hours before any foot traffic and a minimum of 7 days for any vehicles or heavy furniture. We highly recommended that carpet squares or similar be placed under vehicle tyres and heavy furniture to protect the floor whilst curing. Note: Whilst coatings are tyre resistant and most tyres do not mark; there can be no guarantees against Tyre Chemical Bleed, leaving protection under tyres indefinitely is advisable. Regular Cleaning / Maintenance: Broom or vacuum when required, if really dirty scrub floor with a recommended mild detergent and soft broom, then hose out or mop allowing to dry. Major Maintenance: Duron recommend you have your coated surface inspected by a professional coating installer around the 5 year period or sooner if showing signs of wear; the floor may require a commercial machine scrub wash, light sand and the application of a further 1 or 2 coats of reglaze to maintain and keep the coated surface in pristine condition. PLEASE ENSURE YOU HAVE READ AND UNDERSTAND ALL DIRECTIONS BEFORE PROCEEDING WITH THE DURON COATING SYSTEM. Thank you for choosing Duron Coating Systems. We are confident that you will be happy with our products. For any further information please do not hesitate to contact our team. Duron Pty Ltd 4 Progress Street YATALA Ph: (07) Fax: (07) sales@duron.com.au Version 2.1

9 to the Floor Covering and Building Industries FACT SHEET no. (7.1) COMMERCIAL care/maintenance CARE AND MAINTENANCE OF YOUR NEWLY COMPLETED SEAMLESS FLOOR: Note: Duron recommend a minimum of 24 hours before any foot traffic and a minimum of 7 days for any vehicles or heavy furniture. We highly recommend that carpet squares or similar be placed under furniture and tyres whilst floor is curing. Note: Whilst coatings are tyre resistant and most tyres do not mark; there can be no guarantees against Tyre Chemical Bleed, leaving protection under tyres indefinitely is advisable. Regular Cleaning / Maintenance: Broom or vacuum when required, if really dirty scrub floor with a recommended mild detergent and soft broom or commercial scrubbing machine, then hose out or mop allowing to dry. Major Maintenance: Duron recommends a professional installer inspects the coated surface around the 3 year period or sooner if the coating is showing signs of wear; the floor may require a commercial machine scrub wash, light sanding and a further 1 or 2 coats of reglaze to maintain and keep the coated surface in pristine condition. PLEASE ENSURE YOU HAVE READ AND UNDERSTAND ALL DIRECTIONS BEFORE PROCEEDING WITH THE DURON COATING SYSTEM. Thank you for choosing Duron Coating Systems. We are confident that you will be happy with our products. For any further information please do not hesitate to contact our team. Version 2.1

TECHNICAL DATA SHEET

TECHNICAL DATA SHEET Dy-Mark EPOXY COAT WATER-BASED DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat Water-Based is a fast dry floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists

More information

TECHNICAL DATA SHEET

TECHNICAL DATA SHEET Dy-Mark EPOXY COAT DIRECTIONS FOR USE Dy-Mark All-In-One Epoxy Coat is a durable floor coating that gives a professional finish to interior bare concrete floors. Epoxy Coat resists hot tyre pick-up and

More information

DATA SHEET DEKSTER 131 SELFLEVELLING FLOOR COAT / UNDERLAY

DATA SHEET DEKSTER 131 SELFLEVELLING FLOOR COAT / UNDERLAY (Page 1 of 8 ) GENERAL DESCRIPTION - Dekster 131 self levelling is a contemporary coating that achieves hard wearing, utilitarian floor surfaces in a range of natural tones to offset any style of interior.

More information

Application Guide GARAGE & COMMERCIAL FLOORS

Application Guide GARAGE & COMMERCIAL FLOORS Application Guide GARAGE & COMMERCIAL FLOORS REQUIRED TOOLS & MATERIALS - CHECKLIST Flexstone Coatings products (ensure you have enough) Flat Squeegee and Pole (Optional) Disposable brushes (3-4 ) Roller

More information

Product Information. DiamondCoat Polyurethane Concrete Floor Finish Clear, high build, high abrasion resistant, decorative concrete floor coating

Product Information. DiamondCoat Polyurethane Concrete Floor Finish Clear, high build, high abrasion resistant, decorative concrete floor coating Product Information DiamondCoat Polyurethane Concrete Floor Finish Clear, high build, high abrasion resistant, decorative concrete floor coating Description Crommelin DiamondCoat Polyurethane Concrete

More information

DESCRIPTION FEATURES AND BENEFITS AREAS OF USE. DiamondCoat Polyurethane Concrete Floor Finish is suitable for use in the following areas:

DESCRIPTION FEATURES AND BENEFITS AREAS OF USE. DiamondCoat Polyurethane Concrete Floor Finish is suitable for use in the following areas: Product Information Technical Data Sheet - August 2017 DiamondCoat Polyurethane Concrete Floor Finish Clear, highly durable and abrasion resistant, concrete floor coating. DESCRIPTION Crommelin DiamondCoat

More information

Installation Instructions

Installation Instructions Installation Instructions I. GENERAL INFORMATION KEY CHIP-100 FLOORING is a decorative resin flooring system consisting of clear, 100% solids epoxy resin and colored vinyl chips. KEY CHIP-100 FLOORING

More information

Protective Industrial Polymers - USA Manufacturer s Specification

Protective Industrial Polymers - USA Manufacturer s Specification This specification covers InhibiWear BC-Flex Flexible Broadcast System. This system consists of a moisture-tolerant primer, a highly-flexible epoxy/urethane hybrid membrane basecoat and anchor coat, and

More information

Colored Epoxies. Application Instructions. Typical Uses: Overview:

Colored Epoxies. Application Instructions. Typical Uses: Overview: Colored Epoxies Application Instructions Colored Epoxies manufactures high performance Architectural coatings in two part, clear and colored epoxies, that are a cost-effective solution for substrate protection.

More information

Application Guide. PaveCoat

Application Guide. PaveCoat Application Guide PaveCoat This guide has been developed to provide comprehensive preparation and application recommendations for a variety of concrete surfaces. Whilst all endeavours have been taken to

More information

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating. This resinous flooring specification consists of a flexible hybrid polymer primer and basecoat, urethane concrete slurry resurfacer, and double broadcast decorative vinyl flake system based on aliphatic

More information

TERMISHINE PRODUCT INFORMATION WESTERN AUSTRALIA

TERMISHINE PRODUCT INFORMATION WESTERN AUSTRALIA TERMISHINE PRODUCT INFORMATION WESTERN AUSTRALIA RESILIENT FLOOR SURFACES Termi Home & Commercial (WA) proudly introduces a boutique range of concrete floor finishes and sealers for residential and commercial

More information

Flowfast Terrosso (2mm)

Flowfast Terrosso (2mm) Technical Profile Flowfast Terrosso (2mm) A seamless, rapid curing, decorative, durable MMA floor finish that transforms commercial and industrial environments. Typically used in public areas including

More information

Protective Industrial Polymers - USA Manufacturer s Specification MOISTURE-BREATHABLE ESD-CONTROL HIGH-BUILD COATING SYSTEM February 11, 2015

Protective Industrial Polymers - USA Manufacturer s Specification MOISTURE-BREATHABLE ESD-CONTROL HIGH-BUILD COATING SYSTEM February 11, 2015 This specification covers InhibiStat HB-MB Moisture-Breathable ESD-Control High-Build Coating System. This ESD-control system consists of a moisture-tolerant epoxy primer and basecoat, top coated with

More information

Nutech Concrete Range

Nutech Concrete Range Nu-tech Pavecoat H2O is a single pack water-based acrylic concrete sealer and has been developed to achieve excellent penetration and adhesion characteristics to overcome the problems associated with traditional

More information

Protective Industrial Polymers USA Manufacturer s Specification

Protective Industrial Polymers USA Manufacturer s Specification This specification covers DecoSpec QuartzCast DB Decorative Quartz Double Broadcast Flooring System consisting of a moisture-tolerant primer, two applications of a high-build epoxy basecoat with two colored

More information

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound

ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound ARDEX GUIDE SPECIFICATION ARDEX CD Concrete Dressing and ARDEX CD FINE Concrete Dressing Polymer-Modified, Portland Cement-Based, Resurfacing Compound SECTION 03 01 30 MAINTENANCE OF CAST-IN-PLACE CONCRETE

More information

Technical Data Sheet. Ultralevel Bulkout. Self Levelling High Build Cementitious Underlay

Technical Data Sheet. Ultralevel Bulkout. Self Levelling High Build Cementitious Underlay Technical Data Sheet Ultralevel Bulkout Self Levelling High Build Cementitious Underlay SMF26a 03.07.13 DESCRIPTION Bostik Ultralevel Bulkout is a high build, rapid hardening self levelling polymer modified

More information

FEATURES AND BENEFITS

FEATURES AND BENEFITS Product Information Technical Data Sheet - August 2017 DiamondCoat Full colour coating system to rejuvenate concrete, paving and masonry. DESCRIPTION Crommelin DiamondCoat is designed to recolour, rejuvenate,

More information

PPC Cement TUTORIAL. how to screed a floor

PPC Cement TUTORIAL. how to screed a floor PPC Cement TUTORIAL how to screed a floor Pre-build: TOOLs & Materials ITEM Quantity Check. Builders bucket. Wheelbarrow 3. Shovel 4. Builder s line 5. 50mm steel pegs 6. Rigid timber forms 7. Flexible

More information

Protective Industrial Polymers - USA Manufacturer s Specification GENERAL USE HIGH-BUILD ESD-CONTROL COATING SYSTEM February 11, 2015

Protective Industrial Polymers - USA Manufacturer s Specification GENERAL USE HIGH-BUILD ESD-CONTROL COATING SYSTEM February 11, 2015 This specification covers InhibiStat HB-G General Use High-Build ESD-Control Coating System. This ESD-control system consists of an epoxy primer, followed by a high-build ESD epoxy topcoat. This general

More information

Protective Industrial Polymers Canada Manufacturer s Specification February 11, 2015

Protective Industrial Polymers Canada Manufacturer s Specification February 11, 2015 This specification covers HealthSpec FiberWall Antimicrobial Glass and Fiber-Reinforced Wall Coating System. A high-performance antimicrobial wall system consisting of an antimicrobial vertical-substrate

More information

Application Guide for MasterSeal Roof 3000

Application Guide for MasterSeal Roof 3000 Application Guide for MasterSeal Roof 3000 July 2016 Page 1 of 7 METHOD STATEMENT MasterSeal Roof 3000 MasterSeal M 210 membrane 1. Preparation 1.1. Ensure the concrete is profile free, no ridges or troughs,

More information

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating.

Specifier Notes: Edit the following list as required by the project. List other sections with work directly related to the floor coating. This specification covers an epoxy wall coating system composed of an epoxy block filler, one or two applications of a flexible hybrid polymer basecoat, and top coat of high-performance aliphatic satin

More information

Protective Industrial Polymers - USA Manufacturer s Specification

Protective Industrial Polymers - USA Manufacturer s Specification This specification covers InhibiWear HB-Flex (MVR) Flexible High-Build Coating System. This flexible coating system consists of a moisture vapor reducing primer, a highly-flexible epoxy/urethane hybrid

More information

Protective Industrial Polymers - USA Manufacturer s Specification

Protective Industrial Polymers - USA Manufacturer s Specification This specification covers HangarSpec CR-ESD Chemical-Resistant ESD-Control System. A five coat high-build ESD-Control coating system utilizing a moisture-tolerant primer, high solids epoxy base coat(s),

More information

Protective Industrial Polymers - USA Manufacturer s Specification February 11, 2015

Protective Industrial Polymers - USA Manufacturer s Specification February 11, 2015 This specification covers InhibiStat HB-CR Chemical-Resistant ESD-Control High-Build Coating System. This ESD-control system consists of a chemical-resistant epoxy primer top coated with a highly solvent

More information

FEATURES AND BENEFITS

FEATURES AND BENEFITS Product Information Technical Data Sheet - August 2017 DiamondCoat Paving & Concrete Sealer Gloss Clear, tough semi-gloss to gloss finish surface treatment. DESCRIPTION Crommelin DiamondCoat Paving & Concrete

More information

Concrete Paving Sealer Clear, tough, gloss finish surface treatment.

Concrete Paving Sealer Clear, tough, gloss finish surface treatment. Product Information Technical Data Sheet - December 2017 Concrete Paving Sealer Clear, tough, gloss finish surface treatment. DESCRIPTION Crommelin Concrete Paving Sealer is a tough, gloss finish surface

More information

Protective Industrial Polymers - USA Manufacturer s Specification CHEMICAL-RESISTANT ESD-CONTROL MORTAR SYSTEM February 11, 2015

Protective Industrial Polymers - USA Manufacturer s Specification CHEMICAL-RESISTANT ESD-CONTROL MORTAR SYSTEM February 11, 2015 This specification covers InhibiStat MT-CR Chemical-Resistant ESD-Control Mortar System. The system consists of a chemical-resistant epoxy primer, a trowel-applied solvent-resistant epoxy mortar and top

More information

HTG Concrete Seal. Technical Specifications. Safety. HMIS (Concentrate/RTU) Availability. Directions

HTG Concrete Seal. Technical Specifications. Safety. HMIS (Concentrate/RTU) Availability. Directions HTG Concrete Seal HTG(gray) Concrete Seal is a 2-part, high-solid epoxy resin formulation for extreme durability that dries gray. Use HTG to transform bare concrete or previously coated concrete floors

More information

Protective Industrial Polymers - USA Manufacturer s Specification

Protective Industrial Polymers - USA Manufacturer s Specification This specification covers HealthSpec StatCrobe Antimicrobial Static-Control Coating System consisting of a deep-substrate penetrating antimicrobial concrete pretreatment, moisture-tolerant antimicrobial

More information

3-component epoxy self-smoothing screed

3-component epoxy self-smoothing screed Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data

More information

Flowfast SRQ (2mm) Technical Profile

Flowfast SRQ (2mm)   Technical Profile Technical Profile Flowfast SRQ (2mm) A highly decorative, non-slip, fastcuring MMA resin-based flooring system featuring a blend of coloured quartz granules. Typically used in internal and external applications

More information

Protective Industrial Polymers - USA

Protective Industrial Polymers - USA This specification covers InhibiStat DS Decorative ESD System. A high-performance, ESDcontrol decorative flooring system utilizing a moisture-tolerant primer followed by one or two broadcast applications

More information

Protective Industrial Polymers Canada Manufacturer s Specification

Protective Industrial Polymers Canada Manufacturer s Specification This specification covers DecoSpec QuartzCast SB Decorative Quartz Single Broadcast Flooring System, consisting of a moisture-tolerant primer, high-build epoxy basecoat with colored quartz broadcast, high

More information

Protective Industrial Polymers - USA

Protective Industrial Polymers - USA This specification covers InhibiWear SL-Flex Flexible Slurry System. This system consists of a moisture-tolerant primer, a flexible epoxy slurry, an epoxy urethane hybrid membrane, and a GlossGrip-enhanced

More information

Ultralevel SL Self Levelling Cementitious Underlay

Ultralevel SL Self Levelling Cementitious Underlay Technical Data Sheet Ultralevel SL Self Levelling Cementitious Underlay SMF26a 17.06.13 DESCRIPTION Bostik Ultralevel SL is a rapid hardening self-levelling, single component cementitious underlay. Bostik

More information

WATERPROOFING OF BALCONIES. COLD-LIQUID APPLIED.

WATERPROOFING OF BALCONIES. COLD-LIQUID APPLIED. WATERPROOFING OF BALCONIES. COLD-LIQUID APPLIED. 0) Introduction & summary of systems This document explains the different systems that Krypton Chemical, SL. proposes for the liquid cold applied waterproofing

More information

STERI-FLAKE 470 HYBRID ESTER POLYMER, LIGHT-MEDIUM TRAFFIC, FLAKE FILLED FLOOR SYSTEM LOW ODOR MMA ALTERNATIVE FEATURES

STERI-FLAKE 470 HYBRID ESTER POLYMER, LIGHT-MEDIUM TRAFFIC, FLAKE FILLED FLOOR SYSTEM LOW ODOR MMA ALTERNATIVE FEATURES FEATURES Low Odor & VOC Very Fast Cure Unique Multi Colored Patterns Tough, Durable & Seamless Floor Good UV Stability Protects Substrate from Chemical or Physical Attack Integral Cove, Base and Curb (optional)

More information

TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115)

TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115) TECHNICAL DATA SHEET HYDROPOX #2 4:1 EPOXY (MPI #115) DESCRIPTION: A two component water base epoxy amine coating that provides excellent adhesion, solvent resistance and abrasion resistance with water

More information

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment

ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment ARDEX GUIDE SPECIFICATION ARDEX MRF Moisture-Resistant, Rapid-Drying, Skimcoat Patching Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,

More information

(08/02/04 Supersedes all previous instructions )

(08/02/04 Supersedes all previous instructions ) Comcork Flooring Installation Instructions (08/02/04 Supersedes all previous instructions ) 1. Important Information 1 2. Experienced Contractors & Relevant Standards 1 3. Subfloors 1 3.1 Concrete Subfloors

More information

Product Specification

Product Specification Product Specification Product Name: PORTER S MINERAL SILICATE STAIN PRODUCT DESCRIPTION: is a highly durable coloured silicate dispersion stain for the decoration and protection of old and new fair-faced

More information

FEATURES AND BENEFITS

FEATURES AND BENEFITS Product Information Technical Data Sheet - August 2017 DiamondCoat Slate & Stone Sealer - Satin Clear, tough, low sheen treatment for slate and natural stone. DESCRIPTION Crommelin DiamondCoat Slate &

More information

Flowfast Terrosso (3mm)

Flowfast Terrosso (3mm) Technical Profile Flowfast Terrosso (3mm) A seamless, hard-wearing, rapid curing, decorative, MMA floor finish that transforms commercial and industrial environments. Typically used in public areas including

More information

A guide to protecting masonry with a decorative sheen that extends the life of the surface.

A guide to protecting masonry with a decorative sheen that extends the life of the surface. A guide to protecting masonry with a decorative sheen that extends the life of the surface. WHICH SEALER IS RIGHT FOR THE JOB? United Gilsonite Laboratories (UGL ) manufactures four different clear sealers

More information

Method Statement. For RSA Cement Renders Over Masonry Substrates

Method Statement. For RSA Cement Renders Over Masonry Substrates Method Statement RSA Masonry Renders, Traditional Render and EP Render are all suitable for application over correctly prepared clay bricks and concrete blocks PREPARATION Cleaning:- Ensure all surfaces

More information

Resin Bound and Bonded Surfacing. RonaDeck UV Rubber Granule Tree Pit Base. Resin bound rubber granule porous tree pit system.

Resin Bound and Bonded Surfacing. RonaDeck UV Rubber Granule Tree Pit Base. Resin bound rubber granule porous tree pit system. FEATURES SuDS compliant highly permeable UV stable non yellowing resin includes recycled rubber granules alternative to tree grilles installed by approved contractors design can accommodate some tree growth

More information

Copyright 2018, The Sherwin-Williams Company ISSUED MAY CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY

Copyright 2018, The Sherwin-Williams Company ISSUED MAY CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY Copyright 2018, The Sherwin-Williams Company ISSUED MAY 2018 09 67 00 CARB FLUID APPLIED FLOORING FOR CONCRETE THE SHERWIN-WILLIAMS COMPANY INDUSTRIAL INTERIOR SPECIFICATION GUIDE This Painting Schedule

More information

Flowfast SR (3mm) Technical Profile

Flowfast SR (3mm)  Technical Profile Technical Profile FIRE RESISTANCE EN 13505-1 SLIP RESISTANCE Method described in AS4586-2013 Bfl-s1 Dry & Wet Rating is dependant on specification (in accordance with AS4586-2013) Flowfast SR (3mm) A durable,

More information

Terms and Conditions of Sale All purchases are subject to our published Terms and Conditions of Sale visit

Terms and Conditions of Sale All purchases are subject to our published Terms and Conditions of Sale visit Important Notice Any circumstances not covered by this guide should be referred to Regupol (Australia) Pty. Ltd. or its Distributors for any particular attention required. There are many factors that may

More information

Pool Paving Sealer Clear, natural finish, water repellent treatment.

Pool Paving Sealer Clear, natural finish, water repellent treatment. Product Information Technical Data Sheet - December 2017 Pool Paving Sealer Clear, natural finish, water repellent treatment. DESCRIPTION Pool Paving Sealer is a clear, water repellent treatment that penetrates

More information

TECHNICAL DATA SHEET

TECHNICAL DATA SHEET Page 1of 5 PRODUCT DESCRIPTION PROPERTIES COLOUR GLOSS LEVEL WEATHERING UT100 2-Pack topcoat is an unmodified acrylic polyurethane designed to maintain maximum appearance for the maximum length of time.

More information

AQUATITE. Also designed as: Crack/gap filler for masonry and unglazed ceramics Sealants against leaks Repairer for roof cracks and gutters

AQUATITE. Also designed as: Crack/gap filler for masonry and unglazed ceramics Sealants against leaks Repairer for roof cracks and gutters AQUATITE Revision Date: september 2007 Description Bondall AquaTite is a grey, brushable, waterproofing coating that forms a flexible yet tough, seamless membrane. This single pack product exceeds the

More information

Protective Industrial Polymers Canada

Protective Industrial Polymers Canada This specification covers InhibiCrobe TB Antimicrobial Thick-Build Coating System. A highperformance flooring system consisting of an antimicrobial concrete pretreatment, an antimicrobial moisture-tolerant

More information

TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR

TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR TECHNICAL DATA SHEET HYDROPOX #4 QD 1:1 EPOXY WATERWHITE CLEAR DESCRIPTION: A two component water base epoxy amine coating that provides excellent adhesion, solvent resistance and abrasion resistance with

More information

EPILOX HS TECHNICAL DATA SHEET. Solvent Free Epoxy Coating System DESCRIPTION

EPILOX HS TECHNICAL DATA SHEET. Solvent Free Epoxy Coating System DESCRIPTION EPILOX HS Solvent Free Epoxy Coating System DESCRIPTION Aftek Epilox HS is high performance, 100% solids, three component, and solvent free industrial epoxy coating system available in a range of colours.

More information

Application Guide for. MasterSeal Traffic 1500MD

Application Guide for. MasterSeal Traffic 1500MD Application Guide for MasterSeal Traffic 1500MD Medium duty traffic deck crack-bridging waterproofing system February 2016 Page 1 of 9 1. Recommended uses 1.1 MasterSeal Traffic 1500MD is intended for

More information

Fosroc Nitodek UR200 System

Fosroc Nitodek UR200 System Flexible, skid-resistant car park decking system for exposed and intermediate decks Uses Waterproofing decking system for new and existing exposed car park decks and ramps. Advantages Seamless Easy to

More information

DESCRIPTION. DiamondCoat FEATURES AND BENEFITS AREAS OF USE

DESCRIPTION. DiamondCoat FEATURES AND BENEFITS AREAS OF USE Product Information Technical Data Sheet - August 2017 DiamondCoat Water Based Paving & Concrete Sealer Clear, protective coating with excellent water, stain and dirt resistance. DESCRIPTION Crommelin

More information

Asphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE

Asphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE Asphalt Maintenance PRODUCTS INFORMATION AND INSTALLATION GUIDE TABLE OF CONTENT About RESISTO 2 Asphalt Cleaner and Degreaser 3 Oil Spot Primer 3 Liquid Crack Filler 4 Rubberized Crack Filler 4 Levelling

More information

Installation Guide. Preparation of a Polished Concrete Subfloor up to 98% RH

Installation Guide. Preparation of a Polished Concrete Subfloor up to 98% RH Installation Guide The following is a guide of how to install IOBAC paramagnetic resin over the following substrate. This is a guide listed out in bullet points for you to follow as a continuation to your

More information

Dynacryl Acrylic Resin Based Protective & Anti-Carbonation Coating For Concrete & Masonry Surface

Dynacryl Acrylic Resin Based Protective & Anti-Carbonation Coating For Concrete & Masonry Surface Technical Data Sheet Dynacryl Acrylic Resin Based Protective & Anti-Carbonation Coating For Concrete & Masonry Surface Description Bostik Dynacryl is a solvent based clear acrylic coating for a protective

More information

SILASEC DESCRIPTION FEATURES AND BENEFITS SURFACE PREPARATION

SILASEC DESCRIPTION FEATURES AND BENEFITS SURFACE PREPARATION SILASEC WP0001 REVISED: JANUARY 2002 DESCRIPTION Bondall Silasec is a concentrated liquid waterproofing compound designed to be used with Portland type A or type GP cements to form a permanent waterproof

More information

CERAM-KOTE COATINGS, INCORPORATED CERAM-KOTE and CERAM-FLOOR PRODUCTS APPLICATION TO CONCRETE SURFACES SPECIFICATION

CERAM-KOTE COATINGS, INCORPORATED CERAM-KOTE and CERAM-FLOOR PRODUCTS APPLICATION TO CONCRETE SURFACES SPECIFICATION Table of Contents: CERAM-KOTE COATINGS, INCORPORATED CERAM-KOTE and CERAM-FLOOR PRODUCTS APPLICATION TO CONCRETE SURFACES SPECIFICATION 1.0 Scope 2.0 General 3.0 Inspection 4.0 Surface Preparation 5.0

More information

SECTION HYDRAULIC CEMENT UNDERLAYMENT

SECTION HYDRAULIC CEMENT UNDERLAYMENT ARDEX GUIDE SPECIFICATION ARDEX V 1200 Self-Leveling Underlayment A Self-Leveling Underlayment that Consists of a Blend of Portland Cements, Other Hydraulic Cements and Polymers for Interior Applications

More information

1. CMP SPECIALTY PRODUCTS 210 calcium aluminate/portland cement based self-leveling underlayment and topping

1. CMP SPECIALTY PRODUCTS 210 calcium aluminate/portland cement based self-leveling underlayment and topping SECTION 09699 RECOMMENDED SPECIFICATION FOR CMP SPECIALTY PRODUCTS LOCKDOWN 100% SOLIDS, TWO COMPONENT, RESIN BASED, MEMBRANE FORMING, MOISTURE MITIGATION SYSTEM PART 1- GENERAL 1.01 RELATED DOCUMENTS

More information

>>> RESIDENTIAL AND COMMERCIAL ONE DAY FLOORS REPAIR > RESTORE > RENEW

>>> RESIDENTIAL AND COMMERCIAL ONE DAY FLOORS REPAIR > RESTORE > RENEW >>> RESIDENTIAL AND COMMERCIAL ONE DAY FLOORS REPAIR > RESTORE > RENEW WWW.APOLLOCONCRETECOATINGS.COM WWW.APOLLOCONCRETECOATINGS.COM ABOUT US Apollo Concrete Coatings, is a Division of Apollo Drywall &

More information

Method Statement. For RSA Coating Systems Over M Grade Expanded Polystyrene (EPS)

Method Statement. For RSA Coating Systems Over M Grade Expanded Polystyrene (EPS) Method Statement For RSA Coating Systems Over M Grade Expanded Polystyrene RSA strongly recommend the use of our full render, texture paint systems over polystyrene substrates. We DO NOT recommend mixing

More information

PEKAY T570 RUBBERSEAL

PEKAY T570 RUBBERSEAL PEKAY T570 RUBBERSEAL DESCRIPTION Pekay Rubberseal T570 is a rubber-latex modified anionic bitumen emulsion, which dries to a pliable, flexible, waterproof, black coating. It may be used for a variety

More information

ASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED TYPE. Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION

ASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED TYPE. Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION [ TECHNICAL BULLETIN ] ASTEC ANTI-GRAFFITI CLEAR COATING POLYURETHANE SILICONE MODIFIED Sumolac PRODUCT TYPE Aliphatic 2 Pack Polyurethane Anti-graffiti coating. PRODUCT DESCRIPTION Astec Sumolac is a

More information

METHOD STATEMENT 001 CONCRETE BALCONY WATERPROOFING FOR DIRECT FIXED TILES

METHOD STATEMENT 001 CONCRETE BALCONY WATERPROOFING FOR DIRECT FIXED TILES This Document is designed to cover best practice installation methods for the installation of a class 2/3 waterproof membrane system to external concrete balconies in accordance with AS 4654.2 PRELIMINARY

More information

LUXAPOOL CHLORINATED RUBBER POOL COATING

LUXAPOOL CHLORINATED RUBBER POOL COATING Page 1 LUXAPOOL CHLORINATED RUBBER POOL COATING POOLS PREVIOUSLY PAINTED WITH CHLORINATED RUBBER SURFACE PREPARATION 1. Using a stiff brush or broom, scrub the entire surface with diluted LUXAPOOL Concentrated

More information

Method Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels

Method Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels Method Statement For RSA Coating Systems Over AAC Lightweight Blocks RSA strongly recommend the use of our full render, texture and protective coating systems over AAC lightweight blocks. We DO NOT recommend

More information

Method Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels

Method Statement. For RSA Coating Systems Over AAC Lightweight Blocks N.B. Please refer to separate Application Guidelines for AAC Lightweight Panels Method Statement For RSA Coating Systems Over AAC Lightweight Blocks RSA strongly recommend the use of our full render, texture and protective coating systems over AAC lightweight blocks. We DO NOT recommend

More information

Application and Maintenance Guide

Application and Maintenance Guide Application and Maintenance Guide www.timberprocoatings.com General Information Timber Pro s objective is to provide any user of our products with the adequate information to properly prepare, restore

More information

ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment

ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment ARDEX GUIDE SPECIFICATION ARDEX FEATHER FINISH Self-Drying, Cement-Based Finish Underlayment SECTION 03 01 30 Maintenance of Cast-In-Place Concrete PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general

More information

Pre-treatment Materials

Pre-treatment Materials Pre-treatment Materials Paint More Than Colour Keim Mineral Paints - The Mineral Difference Pre-treatment When decorating surfaces, effective pre-treatment will significantly extend the longevity and protection

More information

Protective Industrial Polymers Canada

Protective Industrial Polymers Canada This specification covers InhibiStat SL-Flex Flexible ESD-Control Slurry System. This system consists of a moisture-tolerant primer, a highly-flexible epoxy slurry. a hybrid membrane coating and top coat

More information

Sikafloor -264 is a two part, economic, solvent-free coloured epoxy resin, suitable for use under hot climate condition.

Sikafloor -264 is a two part, economic, solvent-free coloured epoxy resin, suitable for use under hot climate condition. Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -264 2-part epoxy roller and seal coat Construction Product Description Sikafloor -264 is a two part, economic, solvent-free coloured

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX ARDIFLO Pump System Underlayments SECTION 07 26 19 TOPICAL MOISTURE VAPOR EMISSION SYSTEM WITH ARDEX

More information

ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface

ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface ARDEX GUIDE SPECIFICATION ARDEX K 521 Self-Leveling Concrete Topping with Aggregate Surface SECTION 03 54 16 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings, general provisions of the Contract, and

More information

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings

ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings ARDEX GUIDE SPECIFICATION ARDEX MC RAPID One-Coat Moisture Control System For Concrete to Receive ARDEX Underlayments and Toppings SECTION 07 26 19 TOPICAL MOISTURE VAPOR MITIGTION SYSTEM PART 1 - GENERAL

More information

Sealers Full Instructions Preparation, Application & Recoat

Sealers Full Instructions Preparation, Application & Recoat Sealers Full Instructions Preparation, Application & Recoat Surface Preparation All surfaces must be clean all contaminants including dirt, dust, grease, oil, curing compounds, cement laitance, airborne

More information

PORTER S ORIGINAL LIME WASH

PORTER S ORIGINAL LIME WASH Product Specification Product Name: PORTER S ORIGINAL LIME WASH PRODUCT DESCRIPTION: ENVIRONMENTAL INFORMATION: is a unique lime based coating blended with natural pigments which is designed to create

More information

Installation Instructions

Installation Instructions Installation Instructions KEY LASTIC CHIP 100 FLOORING I. GENERAL INFORMATION KEY LASTIC CHIP-100 FLOORING is a resilient decorative resin flooring system consisting of 100% solids resilient epoxy resins

More information

PRODUCT DATA SHEET Sikafloor -264 HC

PRODUCT DATA SHEET Sikafloor -264 HC PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part, economic, solvent-free coloured epoxy resin. USES may only be used by experienced professionals. Roller coat for concrete

More information

New Zealand A Division of Nuplex Industries (NZ) Limited Auckland T: F:

New Zealand A Division of Nuplex Industries (NZ) Limited   Auckland T: F: Technical Data Sheet Date: OCT 2015 Replaces: Feb 2014 AQUAKEM (AQUAGUARD 101) Waterproofing GENERIC TYPE: Waterbased waterbased epoxy coating supplied in parts A & B, mixed prior to application. Used

More information

FEATURES AND BENEFITS

FEATURES AND BENEFITS Product Information Technical Data Sheet - August 2017 DiamondCoat Slate & Stone Sealer Natural Clear, tough, natural finish treatment for slate and natural stone. DESCRIPTION Crommelin DiamondCoat Slate

More information

RESURFACES PROPERLY PREPARED WEATHERED WOOD AND CONCRETE

RESURFACES PROPERLY PREPARED WEATHERED WOOD AND CONCRETE Top Of Page RESURFACES PROPERLY PREPARED WEATHERED WOOD AND CONCRETE Smooth Finish or Textured Finish Find answers to your questions on BEHR PREMIUM ADVANCED DECKOVER in our FAQs below. For detailed product

More information

StrataWorx Tile. Installation Guidelines 1. CONDITION YOUR SITE AND TEST 2. PREPARE THE FLOOR

StrataWorx Tile. Installation Guidelines 1. CONDITION YOUR SITE AND TEST 2. PREPARE THE FLOOR Notice: For best results, review the following guidelines prior to installation. Shaw will not be responsible for improper installation and failure to follow these guidelines may result in limiting warranty

More information

For detailed product information, visit our DeckOver, Textured DeckOver or Extra Textured Deckover product pages.

For detailed product information, visit our DeckOver, Textured DeckOver or Extra Textured Deckover product pages. Top Of Page BRINGS NEW LIFE TO OLD WOOD & CONCRETE Find answers to your questions on BEHR PREMIUM DECKOVER in our FAQs below. For detailed product information, visit our DeckOver, Textured DeckOver or

More information

PRODUCT DATA SHEET Sikafloor -264 HC

PRODUCT DATA SHEET Sikafloor -264 HC PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part, economic, solvent-free coloured epoxy resin. USES may only be used by experienced professionals. Roller coat for concrete

More information

PRE-TREATMENT MATERIALS KEIM MINERAL PAINTS

PRE-TREATMENT MATERIALS KEIM MINERAL PAINTS PRE-TREATMENT MATERIALS KEIM MINERAL PAINTS PRE-TREATMENT When decorating surfaces, effective pre-treatment will significantly extend the longevity and protection of the painted system. This is particularly

More information

LUXAPOOL EPOXY POOL COATING

LUXAPOOL EPOXY POOL COATING Page 1 LUXAPOOL EPOXY POOL COATING POOLS PREVIOUSLY PAINTED WITH EPOXY SURFACE PREPARATION 1. Using a stiff brush or broom, scrub the entire surface with diluted LUXAPOOL Concentrated Wash (mixed at a

More information

Construction. 3-part cement and epoxy combination micro mortar for surface sealing. Product Description 1 1/5. Tests

Construction. 3-part cement and epoxy combination micro mortar for surface sealing. Product Description 1 1/5. Tests Product Data Sheet Edition 29/11/2007 Identification no: 02 03 02 01 002 0 000002 SikaGard -720 EpoCem ZA 3-part cement and epoxy combination micro mortar for surface sealing Construction Product Description

More information

Flooring and Bedding. RonaFloor SL. Self-smoothing seamless epoxy resin flooring system

Flooring and Bedding. RonaFloor SL. Self-smoothing seamless epoxy resin flooring system FEATURES self smoothing epoxy floor screed seamless high strength decorative good chemical resistance easy to clean can be applied to green concrete with use of RonaFloor Epoxy DPM Description RonaFloor

More information

INSTALLATION INFORMATION

INSTALLATION INFORMATION INSTALLATION INFORMATION INTRODUCTION We have prepared the following recommendations and instructions that apply to most applications. Only factory-approved adhesives are to be used for the warranty to

More information

DUR-A-FLEX, Inc. Page 1 of 6

DUR-A-FLEX, Inc. Page 1 of 6 DUR-A-FLEX, Inc. Page 1 of 6 SECTION 09 67 23-RESINOUS FLOORING DUR-A-CHIP EPOXY BROADCAST WITH URETHANE TOPCOAT Date:01/13 PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the

More information