All chimney liners and accessories are made of stainless steel or aluminum!

Transcription

1 All chimney liners and accessories are made of stainless steel or aluminum! FEAS Forest Énergie Air Solutions 9265 Le Royer, Montréal, (Québec) Canada H1P 3H7 Office : (514) Telephone Toll free: 1-(844) Fax : (514) Info@feas.ca richard@feas.ca

2 Table of Contents STAINLESS STEEL CHIMNEY LINER SYSTEM - Fumeflex typical Usage... 4 FUMEFLEX STAINLESS STEEL KIT (Price List) - Base-T Kit (Fast Clip) Base-T Kit (Clamp) Base-T Kit (Regular) Kit for Insert Kit for gas Liner only Price list summary STAINLESS STEEL ACCESSORIES (Price List) - Rain Cap, Flashing extension, Flashing Base-T (Regular), (Clamp), (Fast Clip) Sleeve (Drop in), Dripless Connector, Insert Starter Elbow starter, Elbow 90o - 45o, Mortar Guard, Wall Plate HIGH TEMPERTATURE INSULATION 16 INSTALLATION AND MAINTENANCE FOR ALL FUMEFLEX - Recommendations Installation guide Guarantee Insulation & Maintenance Instructions Maintenance Record Maintenance booklet ALUMINIUM CHIMNEY LINER SYSTEM - Fumeflex typical usage FUMEFLEX ALUMINUM KITS (Price List) - Complete Kit Fireplace Kit Liner only FUMEFLEX ALUMINUM ACCESSORIES (Price List) Rain Cap, Flashing Motor Guard, Wall Plate DIRECT-VENT (Price List) Aluminum Liner 2 Folds for gas

3 Table of Contents TECHNICAL DOCUMENTS Semi-Rigid Air Duct - Ventflex AS Non Insulated Ventflex ASG Thermal Polyester vapour barrier Ventflex ASA Thermal Aluminium vapour barrier Ventflex ASAS Thermal Aluminium vapour barrier Ventflex ASPG Acoustic Polyester vapour barrier Ventflex ASPA Acoustic Aluminium vapour barrier VENTFLEX (Price List) - Semi-rigid Air duct in aluminum Flexible Air Duct - Peflex 4P Non Insulated Peflex 4PG Thermal Polyester vapour barrier Peflex 4PA Thermal Aluminum vapour barrier Peflex 4PPG Acoustic Polyester vapour barrier Peflex 4PPA Acoustic Aluminum vapour barrier Peflex 4PPGG Medical - Acoustic 2 Polyester vapor Barrier PEFLEX 4P (Price List) - Flexible Aluminum Air Duct Flexible Air Duct - Peflex 3P Non insulated Peflex 3PG Thermal Polyester vapour barrier Peflex 3PPG Acoustic Polyester vapour barrier PEFLEX 3P (Price List) - Flexible Aluminium Air Duct... 48

4 Catalogue.Eng. 4 FEAS STAINLESS STEEL CHIMNEY LINERS FUMEFLEX Chimney Liner Forest Énergie et Air Solutions (FEAS) offer you stainless steel chimney liner kits made in Canada, ULC certified and that meet the Canadian Rain Cap building standards. All our FUMEFLEX chimney liners are made of tightly corrugated 316 Ti stainless steel, providing Protects against water infiltration Prevents animals and debris to fall in Rust resistant Prevents air to enter and humidity to form the exceptional strength and flexibility required for this type of liner. Flashing Since 1992, it is mandatory for all built-in stoves to be connected to a stainless steel chimney liner. But for safety and/or efficiency reasons, all Thick 14 x 14 base 304 stainless steel Rust resistant Water infiltration resistant the wood and gas chimneys must be equipped with a stainless steel liner. Sleeve Add stability to the flashing and base T therefore offering added security while cleaning FUMEFLEX Kits Each kit contains: a meshed rain cap, flashing sleeve a flashing, a FUMEFLEX liner, a base T sleeve, a base T or an insert starter and 16 stainless steel screws. Insert Starter Our accessories are built of grade 304-2B-26G stainless steel. The continuous welds leave no room for joint separation and are without leakage, which ensures unparalleled durability. All kits are complete and easy to install. Regular T de base En angled The FEAS products are sold separately and guaranteed for life. Certain restrictions apply. Fast Clip tightening collar Other accessories available Flashing extension 12 or 14 Base T extension 12 or 14 Dripless connector 45 or 90 elbow screwed-in

5 5 STAINLESS STEEL LINER Specification: Stainless steel 316 Ti, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required Kit Includes: Rain cap, Flashing Sleeve, flashing, Fumeflex Liner, sleeve base-t, base-t (Clip), 16 stainless steel screws. Base Tee (FAST CLIP) PRICE LIST Diameter SSLI0320A SSLI0325A SSLI0330A SSLI0335A SSLI0340A SSLI0345A SSLI0350A SSLI0420A SSLI0425A SSLI0430A SSLI0435A SSLI0440A SSLI0445A SSLI0450A SSLI0520A SSLI0525A SSLI0530A SSLI0535A SSLI0540A SSLI0545A SSLI0550A SSLI05.520A SSLI05.525A SSLI05.530A SSLI05.535A SSLI05.540A SSLI05.545A SSLI05.550A SSLI0620A SSLI0625A SSLI0630A SSLI0635A SSLI0640A SSLI0645A SSLI0650A 6 reg SSLI06R20A SSLI06R25A SSLI06R30A SSLI06R35A SSLI06R40A SSLI06R45A SSLI06R50A 7 SSLI0720A SSLI0725A SSLI0730A SSLI0735A SSLI0740A SSLI0745A SSLI0750A SSLI0820A SSLI0825A SSLI0830A SSLI0835A SSLI0840A SSLI0845A SSLI0850A SSLI0920A SSLI0925A SSLI0930A SSLI0935A SSLI0940A SSLI0945A SSLI0950A SSLI1020A SSLI1025A SSLI1030A SSLI1035A SSLI1040A SSLI1045A SSLI1050A

6 6 STAINLESS STEEL LINER Specification: Stainless steel 316 Ti, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required Kit Includes: Rain cap, Flashing Sleeve, flashing, Fumeflex Liner, sleeve base-t, base-t (Clamp), 16 stainless steel screws. Basic-T Kit (clamp) PRICE LIST Diameter SSLI0320AD SSLI0325AD SSLI0330AD SSLI0335AD SSLI0340AD SSLI0345AD SSLI0350AD SSLI0420AD SSLI0425AD SSLI0430AD SSLI0435AD SSLI0440AD SSLI0445AD SSLI0450AD SSLI0520AD SSLI0525AD SSLI0530AD SSLI0535AD SSLI0540AD SSLI0545AD SSLI0550AD SSLI05.520AD SSLI05.525AD SSLI05.530AD SSLI05.535AD SSLI05.540AD SSLI05.545AD SSLI05.550AD SSLI0620AD SSLI0625AD SSLI0630AD SSLI0635AD SSLI0640AD SSLI0645AD SSLI0650AD 6 reg SSLI06R20AD SSLI06R25AD SSLI06R30AD SSLI06R35AD SSLI06R40AD SSLI06R45AD SSLI06R50AD SSLI0720AD SSLI0725AD SSLI0730AD SSLI0735AD SSLI0740AD SSLI0745AD SSLI0750AD SSLI0820AD SSLI0825AD SSLI0830AD SSLI0835AD SSLI0840AD SSLI0845AD SSLI0850AD SSLI0920AD SSLI0925AD SSLI0930AD SSLI0935AD SSLI0940AD SSLI0945AD SSLI0950AD SSLI1020AD SSLI1025AD SSLI1030AD SSLI1035AD SSLI1040AD SSLI1045AD SSLI1050AD

7 4$ Catalogue.web.Eng. 7 STAINLESS STEEL LINER Specification: Stainless steel 316 Ti, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required Kit Includes: Rain cap, Flashing Sleeve, flashing, Fumeflex duct, sleeve base-t, base-t (Regular), 16 stainless steel screws. Basic-T (Regular) PRICE LIST Diameter SSLI0320AR SSLI0325AR SSLI0330AR SSLI0335AR SSLI0340AR SSLI0345AR SSLI0350AR SSLI0420AR SSLI0425AR SSLI0430AR SSLI0435AR SSLI0440AR SSLI0445AR SSLI0450AR SSLI0520AR SSLI0525AR SSLI0530AR SSLI0535AR SSLI0540AR SSLI0545AR SSLI0550AR SSLI05.520AR SSLI05.525AR SSLI05.530AR SSLI05.535AR SSLI05.540AR SSLI05.545AR SSLI05.550AR SSLI0620AR SSLI0625AR SSLI0630AR SSLI0635AR SSLI0640AR SSLI0645AR SSLI0650AR 6 reg SSLI06R20AR SSLI06R25AR SSLI06R30AR SSLI06R35AR SSLI06R40AR SSLI06R45AR SSLI06R50AR SSLI0720AR SSLI0725AR SSLI0730AR SSLI0735AR SSLI0740AR SSLI0745AR SSLI0750AR SSLI0820AR SSLI0825AR SSLI0830AR SSLI0835AR SSLI0840AR SSLI0845AR SSLI0850AR SSLI0920AR SSLI0925AR SSLI0930AR SSLI0935AR SSLI0940AR SSLI0945AR SSLI0950AR SSLI1020AR SSLI1025AR SSLI1030AR SSLI1035AR SSLI1040AR SSLI1045AR SSLI1050AR

8 8 STAINLESS STEEL LINER Specification: Stainless steel 316 Ti, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required Kit Includes: Rain cap, Flashing Sleeve, flashing, Fumeflex Liner, sleeve base-t, base-t (Insert starter), 16 stainless steel screws. Insert kit PRICE LIST Diameter SSLI0320B SSLI0325B SSLI0330B SSLI0335B SSLI0340B SSLI0345B SSLI0350B SSLI0420B SSLI0425B SSLI0430B SSLI0435B SSLI0440B SSLI0445B SSLI0450B SSLI0520B SSLI0525B SSLI0530B SSLI0535B SSLI0540B SSLI0545B SSLI0550B SSLI05.520B SSLI05.525B SSLI05.530B SSLI05.535B SSLI05.540B SSLI05.545B SSLI05.550B 6 SSLI0620B SSLI0625B SSLI0630B SSLI0635B SSLI0640B SSLI0645B SSLI0650B 6 reg SSLI06R20B SSLI06R25B SSLI06R30B SSLI06R35B SSLI06R40B SSLI06R45B SSLI06R50B SSLI0720B SSLI0725B SSLI0730B SSLI0735B SSLI0740B SSLI0745B SSLI0750B SSLI0820B SSLI0825B SSLI0830B SSLI0835B SSLI0840B SSLI0845B SSLI0850B SSLI0920B SSLI0925B SSLI0930B SSLI0935B SSLI0940B SSLI0945B SSLI0950B SSLI1020B SSLI1025B SSLI1030B SSLI1035B SSLI1040B SSLI1045B SSLI1050B

9 9 STAINLESS STEEL LINER Specification: Stainless steel 316, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required. Kit includes: Rain cap, Flashing Sleeve, flashing, Fumeflex duct, mortar guard, wall plate, 9 screws in stainless steel. Gas kit PRICE LIST Diameter SSLI0320F SSLI0325F SSLI0330F SSLI0335F SSLI0340F SSLI0345F SSLI0350F SSLI0420F SSLI0425F SSLI0430F SSLI0435F SSLI0440F SSLI0445F SSLI0450F SSLI0520F SSLI0525F SSLI0530F SSLI0535F SSLI0540F SSLI0545F SSLI0550F SSLI05.520F SSLI05.525F SSLI05.530F SSLI05.535F SSLI05.540F SSLI05.545F SSLI05.550F SSLI0620F SSLI0625F SSLI0630F SSLI0635F SSLI0640F SSLI0645F SSLI0650F 6 reg SSLI06R20F SSLI06R25F SSLI06R30F SSLI06R35F SSLI06R40F SSLI06R45F SSLI06R50F SSLI0720F SSLI0725F SSLI0730F SSLI0735F SSLI0740F SSLI0745F SSLI0750F SSLI0820F SSLI0825F SSLI0830F SSLI0835F SSLI0840F SSLI0845F SSLI0850F SSLI0920F SSLI0925F SSLI0930F SSLI0935F SSLI0940F SSLI0945F SSLI0950F SSLI1020F SSLI1025F SSLI1030F SSLI1035F SSLI1040F SSLI1045F SSLI1050F

10 10 STAINLESS STEEL LINER Specification: Stainless steel 316 Ti, closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required. Liner only PRICE LIST Diameter SSLI0320 SSLI0325 SSLI0330 SSLI0335 SSLI0340 SSLI0345 SSLI0350 SSLI0420 SSLI0425 SSLI0430 SSLI0435 SSLI0440 SSLI0445 SSLI0450 SSLI0520 SSLI0525 SSLI0530 SSLI0535 SSLI0540 SSLI0545 SSLI0550 SSLI SSLI SSLI SSLI SSLI SSLI SSLI SSLI0620 SSLI0625 SSLI0630 SSLI0635 SSLI0640 SSLI0645 SSLI reg SSLI06R20 SSLI06R25 SSLI06R30 SSLI06R35 SSLI06R40 SSLI06R45 SSLI06R SSLI0720 SSLI0725 SSLI0730 SSLI0735 SSLI0740 SSLI0745 SSLI0750 SSLI0820 SSLI0825 SSLI0830 SSLI0835 SSLI0840 SSLI0845 SSLI0850 SSLI0920 SSLI0925 SSLI0930 SSLI0935 SSLI0940 SSLI0945 SSLI0950 SSLI1020 SSLI1025 SSLI1030 SSLI1035 SSLI1040 SSLI1045 SSLI1050

11 11 STAINLESS STEEL LINER KIT Diameter Kit reg 7 8 Fast Clip code SSLI0320A SSLI0325A SSLI0330A SSLI0335A SSLI0340A SSLI0345A SSLI0350A Insert code SSLI0320B SSLI0325B SSLI0430B SSLI0335B SSLI0340B SSLI0345B SSLI0350B Gas Code SSLI0320F SSLI0325F SSLI0330F SSLI0335F SSLI0340F SSLI0345F SSLI0350F Fast Clip Code SSLI0420A SSLI0425A SSLI0430A SSLI0435A SSLI0440A SSLI0445A SSLI0450A Insert Code SSLI0420B SSLI0425B SSLI0430B SSLI0435B SSLI0440B SSLI0445B SSLI0450B Gas Code SSLI0420F SSLI0425F SSLI0430F SSLI0435F SSLI0440F SSLI0445F SSLI0450F Fast Clip Code SSLI0520A SSLI0525A SSLI0530A SSLI0535A SSLI0540A SSLI0545A SSLI0550A Insert Code SSLI0520B SSLI0525B SSLI0530B SSLI0535B SSLI0540B SSLI0545B SSLI0550B Gas Code SSLI0520F SSLI0525F SSLI0530F SSLI0535F SSLI0540F SSLI0545F SSLI0550F Fast Clip code SSLI05.520A SSLI05.525A SSLI05.530A SSLI05.535A SSLI05.540A SSLI05.545A SSLI05.550A Insert code SSLI05.520B SSLI05.525B SSLI05.530B SSLI05.535B SSLI05.540B SSLI05.545B SSLI05.550B Gas Code SSLI05.520F SSLI05.525F SSLI05.530F SSLI05.535F SSLI05.540F SSLI05.545F SSLI05.550F Fast Clip Code SSLI0620A SSLI0625A SSLI0630A SSLI0635A SSLI0640A SSLI0645A SSLI0650A Insert Code SSLI0620B SSLI0625B SSLI0630B SSLI0635B SSLI0640B SSLI0645B SSLI0650B Gas Code SSLI0620F SSLI0625F SSLI0630F SSLI0635F SSLI0640F SSLI0645F SSLI0650F Fast Clip Code SSLI06R20A SSLI06R25A SSLI06R30A SSLI06R35A SSLI06R40A SSLI06R45A SSLI06R50A Insert Code SSLI06R20B SSLI06R25B SSLI06R30B SSLI06R35B SSLI06R40B SSLI06R45B SSLI06R50B Gas Code SSLI06R20F SSLI06R25F SSLI06R30F SSLI06R35F SSLI06R40F SSLI06R45F SSLI06R50F Fast Clip Code SSLI0720A SSLI0725A SSLI0730A SSLI0735A SSLI0740A SSLI0745A SSLI0750A Insert Code SSLI0720B SSLI0725B SSLI0730B SSLI0735B SSLI0740B SSLI0745B SSLI0750B Gas Code SSLI0720F SSLI0725F SSLI0730F SSLI0735F SSLI0740F SSLI0745F SSLI0750F Fast Clip Code SSLI0820A SSLI0825A SSLI0830A SSLI0835A SSLI0840A SSLI0845A SSLI0850A Insert Code SSLI0820B SSLI0825B SSLI0830B SSLI0835B SSLI0840B SSLI0845B SSLI0850B Gas Code SSLI0820F SSLI0825F SSLI0830F SSLI0835F SSLI0840F SSLI0845F SSLI0850F

12 12 Rain Cap reg 7 8 SSRC03 SSRC04 SSRC05 SSRC05.5 SSRC06 SSRC06R SSRC07 SSRC08 Also available in 9 and 10 Flashing Extention reg 7 8 FLEXT0312 FLEXT0412 FLEXT0512 FLEXT FLEXT0612 FLEXT06R12 FLEXT0712 FLEXT FLEXT0318 FLEXT0418 FLEXT0518 FLEXT FLEXT0618 FLEXT06R18 FLEXT0718 FLEXT0818 Also available in 9 and 10 Flashing reg 7 8 SSFL03 SSFL04 SSFL05 SSFL05.5 SSFL06 SSFL06R SSFL07 SSFL08 Also available in 9 and 10

13 / Catalogue.Eng. 13 Base-T (Regular) reg 7 8 BTR03 BTR04 BTR05 BTR05.5 BTR06 BTR06R BTR07 BTR08 Also available in 9 and 10 Base-T (Clamp) reg 7 8 BTS03 BTS04 BTS05 BTS05.5 BTS06 BTS06R BTS07 BTS08 Also available in 9 and 10 Base-T (Fast Clip) reg 7 8 BTA03 BTA04 BTA05 BTA05.5 BTA06 BTA06R BTA07 BTA08 Also available in 9 and 10 Welding technology «Seamless»

14 / Catalogue.web.Eng. 14 Sleeve (Drop in) reg 7 8 SSDI03 SSDI04 SSDI05 SSDI05.5 SSDI06 SSDI06R SSDI07 SSDI08 Also available in 9 and 10 Dripless Connector reg 7 8 DC03 DC04 DC05 DC05.5 DC06 DC06R DC07 DC08 Also available in 9 and 10 Insert Stater reg 7 8 START03 START04 START05 START05.5 START06 START06R START07 START08 Also available in 9 and 10

15 / Catalogue.web.Eng. 15 Elbow Starter 6 ELBOW06D Elbow 90 o - 45 o 90 o ELBOW0390 ELBOW0490 ELBOW0590 ELBOW ELBOW0690 ELBOW0790 ELBOW o ELBOW0345 ELBOW0445 ELBOW0545 ELBOW ELBOW0645 ELBOW0745 ELBOW0845 Also available in 9 and 10 Mortor Guard reg 7 8 MG03 MG04 MG05 MG05.5 MG06 MG06R MG07 MG08 Also available in 9 and 10 Wall Plate reg 7 8 WG03 WG04 WG05 WG05.5 WG06 WG06R WG07 WG08 Also available in 9 and 10

16 16 HIGH TEMPERATURE INSULATION 2300 o F PRODUCT THICK WIDE LONG CODE PRICE 2300 o F Non-Foil Insulation #8 Density ½ IN o F Non-Foil Insulation #8 Density ½ IN o F Foiled Insulation #8 Density ½ INF o F Foiled Insulation #8 Density ½ INF Stainless Steel Mesh For INM3625 Stainless Steel Mesh For INM363O Stainless Steel Mesh INM3635 Stainless Steel Mesh INM7925 Stainless Steel Quick Clamps 2-8 Stainless Steel Quick Clamps 2-13 SSCLAMP08 SSCLAMP013 Listed & Tested UL UL 641- UL441 ULC S-640 ULC S-635

17 17 Fumeflex Lining System Installation and maintenance instructions for smooth and single wall chimney lining kits. We recommend you use an experienced and qualified chimney professional to install your FEAS Lining System. The FEAS lining System has been tested and approved to UL1777 zero-clearance standards for masonry chimneys serving gas, oil or wood-burning appliances. All warranties, states or implied, are void if this product is not properly installed in accordance with the instructions contained in this brochure and in accordance with local requirements. The listing for the FEAS Lining System is void if components other than those supplied as listed components by this manufacturer are used It is important that this chimney liner be installed in accordance with these instructions. Please read all instructions before beginning your installation. Failure to install this system in accordance with these instructions will void the conditions of certification and the manufactures warranty. Office: (514) Telephone Toll Free: 1-(844) ; Fax: (514) Internet Site :

18 18 THE FEAS FUMEFLEX LINING SYSTEM Available in , R The FEAS FUMEFLEX Lining System is intended for use with heating appliances vented through a masonry chimney that burn home heating oil, natural or LP gas and solid fuels (pellet, wood and coal). Use of experimental fuels voids the warranty. This lining system is not for use with Category ll, III, or IV gas burning appliances as defined by the National Fuel Gas Code, NFPA 54, or other appliances that create positive pressures in the chimney system or that cause condensation of corrosive acids on the liner of the chimney. The Fumeflex Lining System is intended for use in an unlined chimney with at least a nominal 4" of masonry all around, a properly built masonry chimney with cracked clay tile liners, or to provide a properly sized flue for a heating appliance installed in a masonry chimney that otherwise meets existing codes. The FEAS FUMEFLEX Lining System may be used to reline a fireplace chimney. The liner must be connected to the top of the smoke chamber by a bottom plate or other means that provides an air-tight and drip-free termination. PARTS LIST The FEAS FUMEFLEX Lining 1 Stainless Steel Liner 2 Stainless Steel Sleeve 1 Stainless Steel Tee Cap 1 Stainless Steel Tee 1 Stainless Steel Rain Cap 1 Stainless Steel flashing INSTALLATION INSTRUCTIONS If chimney requires field drilling, use a 1/4" stainless steel drill bit to drill through the inner section of the chimney liner section. Wall penetration assemblies are not to be located directly behind a heating appliance. The following criteria shall apply to a connector to a masonry chimney: It shall extend through the wall to the inner face or liner but not beyond. It shall be firmly cemented to masonry. If a thimble is used to facilitate removal of the chimney connector for cleaning, the thimble shall be permanently cemented in place with high-temperature cement. The effective area of a connector for a single appliance shall not be less than the area of the appliance flue collar, unless it is part of an engineered venting system. Sizing: Size the liner according to equipment manufacturer s instructions and/or local building codes. The chimney liner must be sized not less than that specified in the appliance manufacturer s instructions. Local approval: Contact local fire or building officials about restrictions and installation inspection in your area. Cleaning existing chimney: The chimney must be clean and free of debris. All soot dirt and creosote including tar and glaze creosote must be removed prior to installation. Proper cleaning of the chimney is a warranty prerequisite. The internal and external condition of the chimney must be checked for safety and repaired as necessary. Run a guide cone up and down the chimney to clear any obstructions and to ascertain that the liner diameter will pass through the chimney s flue opening. Connection to UL listed direct connect system: The liner system may be connected with a UL listed direct connect system which is installed in accordance with the manufacturer s instructions. You must use a stainless steel pipe connector or stainless steel transition or slip connector to make the connection. The liner must also be sized (cross sectional area) the same as the direct connect system. Liner installation: Inspect the chimney for cracked, loose or missing bricks or stones. Check for missing mortar joints. The chimney must be a minimum of 4" thick throughout. No chimney should be relined that is not structurally sound. Also inspect the air space clearances between the exterior of the masonry chimney and any combustibles. These clearances must be in accordance with current NFPA 211 standards or the local building codes. Check the height of the chimney to be certain it conforms to the recognized regulations. This installation must include the rain cap, a protective covering or housing for the top of the chimney intended to prevent the entry of rain, snow, animals and birds, and to prevent down drafts. Initial installation of chimneys, fireplaces and vents shall allow inspection of the surroundings to determine that the required clearances have been maintained and that correct provisions for support, stabilization, future inspection and maintenance are in place. INSTALLATION INSTRUCTIONS Continued on next page

19 INSTALLATION INSTRUCTIONS CONTINUED 19 Minimum air space clearance: - 0 For gas oïl - 2 For wood Remove a sufficient amount of brick and mortar to allow access for the installation of the tee s snout at the base of the chimney where the heating appliance vent connector attaches to the tee of the lining system. Separate the tee from its snout. Attach the tee to the liner with the fasteners provided. Drop or pull the liner with the attached tee, without the snout, through the chimney until the tee rests in the base of the chimney where the brick and mortar were previously removed Attach the snout and place the end-cap on the bottom of the T with the fasteners provided. Attach the pipe connecting the heating appliance to the tee s snout. Seal the area around the tee where the brick and mortar were removed with a furnace cement product. Using a high-temperature silicone product, seal the joints where the snout of the tee connects to the pipes from the heating appliance. Connect the heating appliance vent connector to the FEAS Tee System as per local code and appliance manufacturer s written instructions. Slide the flashing over the liner and place on the clay tile and center. Mark the outline of the clay tile on the underside of the flashing. Remove and trim the flashing to the size marked. Trim the liner so that 4" of liner extends above the top of the clay tile.. Apply a wide bead of high-temperature silicone around the top surface of the clay tile. Place the flashing over the liner and slide down onto the silicone. Hold in place firmly to create a good seal. Screw the four fasteners provided through the 2" collar of the flashing and into the liner Do not over-tighten the fasteners. Apply a bead of high-temperature silicone to the inside of the top section of liner and to the lower section of the rain cap. Place the rain cap into the flashing of the liner and push down until the stop bead of the rain cap meets the liner. RAIN CAP RAIN CAP FLASHING NOTE: LEAVE 3-8 OF SPACE BETWEEN THE TOPOF THE INSULATIONG BLANKET WRAP AND THE TOP PLATE FLASHING NOTE: LEAVE AT LEAST 6 OF LINER ABOVE FOIL-FACE FLEXWRAP UNINSULATED INSULATION WRAP PRE-FABRICATED CHIMNEY 6 FUMEFLEX LINING APPLIANCET THIMBLE STOVEPIPE PRE-FABRICATED FIREPLACE UL LISTED FIREPLACE INSERT LISTED TO BE PLACED IN EXISTING UL LISTED FACTORY- BUILT FIREPLACE CLEANING OUT TEE TEE COUVER FUMEFLEX LINING ALUMINIUM SIDE FOIL TAPE RETRACTABLE WIRE MESH

20 THE FEAS FUMEFLEX SYSTEM LIFE WARRANTY 20 FEAS. guarantees the FEAS Fumeflex System stainless steel chimney liner and components are free from manufacturer s material and workmanship defects, corrosion or perforation caused by chimney fires. Lifetime warranty for wood, wood pellets, gas and oil installations when used to vent residential UL listed heating appliances that are Category I residential gas or oil burning heating and hot water systems including gas fireplaces, gas logs, oil stoves, wood-burning stoves and fireplaces. FEAS, guarantees the original purchaser for the lifetime of the product as long as said purchaser owns the home in which the FEAS Fumeflex System stainless steel chimney liner was originally installed. This warranty is subject to the following conditions: FEAS Fumeflex System stainless steel chimney liner and components must be installed by a certified solid fuel professional and in accordance with these written instructions. FEAS Fumeflex System stainless steel chimney liner and components are intended for use in lining and relining masonry chimneys that vent a tested and approved or listed residential appliance for which FEAS Fumeflex System stainless steel chimney liner and components are intended. Annual inspections, maintenance and cleaning must begin one year after the date of the installation and continue once every twelve months thereafter by a certified chimney sweep or a qualified solid fuel professional. The chimney must have a FEAS Fumeflex System chimney cap. Corrosive chemical chimney cleaners must not be used and their use will void the warranty. Driftwood or wood pellets containing salt, treated lumber, plastics, the chimney sweeping log or trash must not be burned and doing so will void the warranty. The maintenance record must be up-to-date. Never use a metal chimney cleaning brush. We strongly recommend the use of a plastic bristle chimney cleaning brush as metal brushes can damage the liner and will void the warranty In case of a chimney fire the liner must be inspected and cleaned by a certified chimney sweep or a qualified solid fuel professional before reuse. If you should need to make a claim under the conditions of this warranty, you must contact the original installer who will provide FEAS with information about your claim. Should a factory inspection of the defective parts in question be required by FEAS, FEAS will pay the shipping cost for the return of the defective parts in question. If FEAS deems the parts to be defective, FEAS will replace the parts at no cost to the original purchaser and said replacement will be FEAS exclusive and final remedy under this warranty. FEAS shall not be liable for any costs for the removal or re-installation of the liner or any liability for special consequential or incidental damages in any way related to or arising out of defects in or damage to the liner. FEAS Fumeflex System stainless steel chimney liner has been tested and approved to UL1777 zero special consequential or incidental damages in any way related to or arising out of defects in or damage to the liner. FEAS Fumeflex System stainless steel chimney liner has been tested and approved to UL1777 zero clearance standards* and all component parts have been tested and listed by UL*. A copy of the test report is available upon request by your installer. FEAS makes no warranty, express or implied, of merchantability or fitness for a particular purpose or otherwise. This warranty gives you specific legal rights. You may have other rights which vary from state to state concerning exclusions or limitation of incidental or consequential damages.

21 Complete and return to FEAS 21 Customer Name: Address: City: Province: Postal Code: Telephone: l: Installer Name: Company: City: Province: Postal Code: Telephone: Installer Date: Dimensions Height: X X Type of Appliance Stove Fireplace Pellet stove Oil Gas Wood Oil Gas Wood Heating system Water Oil Gas Wood Oil Gas Thank you for placing your trust in FEAS team!

22 INSULATING THE LINER PIPE INSTRUCTIONS (IF REQUIRED) 22 Make sure that the bottom connector, either a tee connector or a universal connector, has been installed. The liner must be insulated from the bottom of the connector to the crown. ln the case of a tee connector, the liner must be insulated from where the tee cap is installed up to the crown; with a universal connector, from where the connector would stop on insertion into the heating appliance up to the crown. After determining the distance, roll out the insulating wrap and cut it to the proper length. The insulating wrap must overlap along its length by a minimum of 1 inch. To ensure that you will have the proper width of insulating wrap multiply the liner diameter by 3.14 plus 1 inch for overlap. Although it is not necessary, you may trim the insulating wrap to this amount if you wish. A wider overlap than 1 inch is allowed but may cause difficulty installing in tight clearance situations. Place the insulating wrap foil face down on a level surface. Lay the liner and its bottom termination connector (previously attached) in the center on the insulating wrap. Line up the bottom connector as outlined in the second paragraph. Remember that at the top the insulating wrap will be even with the chimney crown. Start wrapping the insulating wrap around the liner pipe. Hold the wrap in place with foil tape at approximately 1 foot intervals making sure to overlap the insulating wrap by a minimum of 1 inch. You may use spray adhesive to assist you in holding the insulating wrap against the liner pipe. When the insulating wrap is in place around the liner pipe, apply a continuous length of foil tape from the top to the bottom of the overlapped insulating wrap seam. Encapsulate the insulated liner using retractable wire mesh. Unroll the correct size wire mesh and pull it over the entire length of the insulated liner pipe. At the bottom of the insulating wrap secure the mesh and insulating wrap in place with a stainless steel hose clamp. At the top of the liner pipe stretch the wire mesh tight and while holding the mesh tight, clamp the insulating wrap and the wire mesh in place with a stainless steel hose clamp. Trim away any excess wire mesh. With long liner lengths you may also wrap the entire insulated liner pipe with stainless steel wire wrapped spirally and twisted on itself at each end to hold it in place. The insulated liner pipe is now ready to be installed. MAINTENANCE INSTRUCTIONS Cleaning of chimney, if necessary shall be done by methods that do not impair structural or thermal performance. To maintain this warranty the liner assembly must be cleaned and inspected by a certified solid fuel technician yearly before each heating season to ensure that it is free of debris, creosote and condensation and that all parts are in good condition. A written maintenance record must be kept by the homeowner on the warranty card provided. Creosote and Soot-Formation and the Need for Removal When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors may condense on the inside of the chimney liner during slow-burning firing periods. As a result, creosote residue accumulates on the chimney liner. When ignited, this creosote makes an extremely hot fire. The chimney liner system should be inspected at least once every two months during the heating season to determine if a creosote or soot buildup has occurred. If creosote or soot has accumulated, it should be removed to reduce the risk of a chimney fire.

23 MAINTENANCE BOOKLET 23 Installer: Date of installation: Company: Telephone : Adress: City : Province : Postal Code: 1 year installer : 6 th year installer : Work done : Work done : Date : Signature : Date : Signature : 2 nd year installer : 7 th year installer : Work done : Work done : Date : Signature : Date : Signature : 3 rd year installer : 8 th year installer : Work done : Work done : Date : Signature : Date : Signature : 4 th year installer : 9 th year installer : Work done : Work done : Date : Signature : Date : Signature : 5 th year installer : 10 th year installer : Work done : Work done : Date : Signature : Date : Signature : Forest Énergy and Air Solutions 9265 Le Royer, Montréal, Québec, H1P 3H7

24 24 FEAS ALUMINUM CHIMNEY LINERS FUMEFLEX Chimney Liner Forest Énergie et Air Solutions (FEAS) offer you aluminum chimney liner kits made in Quebec, ULC certified and that meet the Canadian building standards. All our FUMEFLEX chimney liners are made of tightly corrugated type 3003 aluminium, Rain Cap Protects against water infiltration Prevents animals and debris to fall in Rust resistant Prevents air to enter and humidity to form providing the exceptional strength and flexibility required for this type of liner. Flashing FUMEFLEX kits Thick 14 x 14 base 304 stainless steel Rust resistant Water infiltration resistant Each kit contains: a meshed rain cap, a flashing, a FUMEFLEX liner, a mortar guard, a wall plate and 9 stainless steel screws. Mortar Guard (galvanized steel) The fireplace kit contains: a meshed rain cap, a flashing, a FUMEFLEX liner and 9 stainless steel screws. Wall plate (galvanized steel) Our accessories are built of type 3003 aluminum. The continuous welds leave no room for joint separation and are without leakage, which ensures unparalleled durability. All kits are complete and easy to install. The FEAS products are sold separately and guaranteed for life. Certain restrictions apply.

25 25 ALUMINUM LINER Specification: Aluminum 3003-type closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required. Kit includes: Rain cap, flashing, Fumeflex Liner, mortar Guard, Wall plate, 9 screws in stainless steel. Complete kit PRICE LIST Diameter ALLI0420C ALLI0425C ALLI0430C ALLI0435C ALLI0440C ALLI0445C ALLI0450C 5 ALLI0520C ALLI0525C ALLI0530C ALLI0535C ALLI0540C ALLI0545C ALLI0550C 6 ALLI06R20C ALLI06R25C ALLI06R30C ALLI06R35C ALLI06R40C ALLI06R45C ALLI06R50C 7 ALLI0720C ALLI0725C ALLI0730C ALLI0735C ALLI0740C ALLI0745C ALLI0750C 8 ALLI0820C ALLI0825C ALLI0830C ALLI0835C ALLI0840C ALLI0845C ALLI0850C

26 26 ALUMINUM LINER Specification: Aluminum 3003-type closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required. Kit includes: Rain cap, flashing, Fumeflex Liner, 6 screws in stainless steel. Fire place kit PRICE LIST Diameter ALLI0420FP ALLI0425FP ALLI0430FP ALLI0435FP ALLI0440FP ALLI0445FP ALLI0450FP 5 ALLI0520FP ALLI0525FP ALLI0530FP ALLI0535FP ALLI0540FP ALLI0545FP ALLI0550FP 6 ALLI06R20FP ALLI06R25FP ALLI06R30FP ALLI06R35FP ALLI06R40FP ALLI06R45FP ALLI06R50FP 7 ALLI0720FP ALLI0725FP ALLI0730FP ALLI0735FP ALLI0740FP ALLI0745FP ALLI0750FP 8 ALLI0820FP ALLI0825FP ALLI0830FP ALLI0835FP ALLI0840FP ALLI0845FP ALLI0850FP

27 27 ALUMINUM LINER Specification: Aluminum 3003-type closely corrugated for strength and flexibility. The joints have seven folds and are knurled to ensure complete sealing to the operating pressure required. Liner Only PRICE LIST Diameter ALLI0320 ALLI0325 ALLI0330 ALLI0335 ALLI0340 ALLI0345 ALLI0350 ALLI0420 ALLI0425 ALLI0430 ALLI0435 ALLI0440 ALLI0445 ALLI0450 ALLI0520 ALLI0525 ALLI0530 ALLI0535 ALLI0540 ALLI0545 ALLI0550 ALLI06R20 ALLI06R25 ALLI06R30 ALLI06R35 ALLI06R40 ALLI06R45 ALLI06R50 ALLI0720 ALLI0725 ALLI0730 ALLI0735 ALLI0740 ALLI0745 ALLI0750 SSLI0820 ALLI0825 ALLI0830 ALLI0835 ALLI0840 ALLI0845 ALLI0850

28 29 Rain Cap ALRC04 ALRC05 ALRC06R ALRC07 ALRC08 Flashing ALFL04 ALFL05 ALFL06R ALFL07 SSFL08 Mortor Guard ALMG04 ALMG05 ALMG06R ALMG07 ALMG08 Wall Plate ALWG04 ALWG 05 ALWG06R ALWG07 ALWG08

29 30 Aluminum Liner 2 folds for gas Interior Exterior Diameter Diameter Length Code Price DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS DVS5850

30 Data sheet 31 Non Isolated Description: Ventilation duct is semi-rigid, lightweight and uninsulated. The Ventflex AS is made of a thin strip of aluminum that is spirally wound and mechanically assembled. The AS Ventflex is waterproof, air tight and corrosion resistant. It adapts to all heating, ventilation system from low to high pressure. Available Diameters: Standard length of 10 feet Material Aluminum Flame Speed <0 flame development <0 Maximum Velocity 4000 ft/min Continuous maximum positive pressure 12 of water Continuous maximum negative pressure 1 of water Temperature Range F à F Flexible thickness 5 mil. (0,105mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

31 Data sheet 32 Thermal Description: Ventilation duct is Semi-Rigid isolated. The ASG Ventflex consists of a thin aluminum strip spirally assembled mechanically. The inner pipe is covered with an insulation glass fiber 1 ½ inches which is coated with a polyethylene vapor barrier. The Ventflex ASG is a high quality product used for most heating and cooling high efficiency. Available Diameters : Standard length of 10 feet Material Aluminum Flame speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/min Continuous maximum Positive pressure 12 of water Continuous maximum Negative pressure 1 of water Temperature Range F à F Insulation coefficient R 4,2 Flexible thickness 5 mil. (0,105mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

32 Data sheet 33 Thermal Description: Ventilation duct is Semi-Rigid isolated. The ASA Ventflex consists of a thin aluminum strip spirally assembled mechanically. The inner pipe is covered with an insulation glass fiber 1 ½ inches which is coated with an aluminum vapor barrier.the Ventflex ASA is a high quality product used for most heating and cooling high efficiency. Available Diameters : Standard length of 10 feet Material Aluminum Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/min Continuous maximum Positive pressure 12 of water Continuous maximum Negative pressure 1 of water Temperature Range F à F Insulation coefficient R 4,2 Flexible thickness 5 mil. (0,105mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

33 Data sheet 34 Thermal Description: Ventilation duct is Semi-Rigid. The ASAS Ventflex consists of a thin aluminum strip spirally assembled mechanically. The inner pipe is covered with an insulation glass fiber 1 ½ inches which is coated semi-rigid. The Ventflex ASAS is a high quality product used for most heating and cooling high efficiency. Available Diameters : Standard length of 10 feet Material Aluminum Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/min Continuous maximum Positive pressure 12 of water Continuous maximum Negative pressure 1 of water Temperature Range F à F Insulation coefficient R 4,2 Flexible thickness 5 mil. (0,105mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

34 Data sheet 35 Acoustic Description: Ventilation Duct is Semi-Rigid isolated. The ASPG Ventflex consists of a thin aluminum strip spirally assembled mechanically. The inner pipe is covered with an insulation glass fiber 1 ½ inches which is coated with a polyethylene vapor barrier. The Ventflex ASPG is a high quality product used for most heating and cooling high efficiency. Available Diameters : Standard length of 10 feet Material Aluminum Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/min Continuous maximum Positive pressure 12 of water Continuous maximum Negative pressure 1 of water Temperature Range F à F Insulation coefficient R 4,2 Flexible thickness 5 mil. (0,105mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

35 Data sheet 36 Acoustic Description: Ventilation duct is Semi-Rigid. The ASPA Ventflex consists of a thin aluminum strip spirally assembled mechanically. The inner pipe is covered with an insulation glass fiber 1 ½ inches which is coated with an aluminum vapor barrier. The Ventflex ASPG is a high quality product used for most heating and cooling high efficiency. Available Diameters : Standard length of 10 feet Material Aluminium Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/min Continuous maximum Positive pressure 12 of water Continuous maximum Negative pressure 1 of water Temperature Range F à F Insulation coefficient R 4,2 Flexible thickness 5 mil. (0,105mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

36 37 Semi-rigid Aluminum Pipe PRICE LIST ORDERS WITH MORE THAN 500 FEET ORDERS WITH LESS THAN 500 FEET DIAMETER REGULAR AS VAPOR- BARRIER GRAY ASG/ASPG VAPOR - BARRIER ALUMINIUM ASA/ASPA DIAMETER REGULAR AS VAPOR- BARRIER GRAY ASG/ASPG VAPOR- BARRIER ALUMINIUM ASA/ASPA

37 Data sheet 38 Non Isolated Description: Flexible air pipe connection consisting of two layers of pure aluminum and of two layers of a polyester binding a galvanized wire. Available Diameters : Standard length of 25 feet Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 15 in. H 2 0 (1.5 kpa) Continuous maximum Negative Pressure,5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature use -20 o F to 140 o F continuous (at 4 inches H 2 0) -20 o F to 180 o F continuous (at 2 inches H 2 0) -20 o F to 180 o F continuous (at ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

38 Data sheet 39 Thermal Description Flexible air pipe connection consisting of two layers of pure aluminum and of two layers of a polyester binding a galvanized wire, a glass fiber insulation of 1 ½ "thick and a polyethylene vapor barrier gray. Available Diameter : Standard Length 25 feet Flame speed < 25 Flame development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 15 in. H 2 0 (1.5 kpa) Continuous maximum Negative pressure,5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature use -20 o F to 140 o F continuous (at 4 inches H 2 0) -20 o F to 180 o F continuous (à 2 inches H 2 0) -20 o F to 250 o F continuous (à ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

39 Data sheet 40 Description Thermal Flexible air pipe connection consisting of two layers of pure aluminum and of two layers of a polyester binding a galvanized wire, a glass fiber insulation of 1 ½ "thick and an aluminum vapor barrier. Available Diameter : Standard Length 25 feet Flame speed < 25 Flame development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 15 in. H 2 0 (1.5 kpa) Continuous maximum Negative pressure,5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature use -20 o F to 140 o F continuous (at 4 inches H 2 0) -20 o F to 180 o F continuous (à 2 inches H 2 0) -20 o F to 250 o F continuous (à ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-US-S-110 US-UL-181 Air duct fitting class 1

40 Data sheet 41 Description Acoustic Flexible air connection consisting of two perforated layers of pure aluminum and of two layers of a bonded polyester galvanized wire leads, a glass fiber insulation of 1 ½ " thick and a vapor barrier gray polyethylene. Available Diameters : Standard Length of 25 feet Flam speed < 25 Flam development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive pressure 15 in. of water Continuous maximum Negative pressure.5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 6 inches H 2 0) -20 o F to 180 o F continuous (at 2 inches H 2 0) -20 o F to 250 o F continuous (at ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1

41 Data sheet 42 Description Acoustic Flexible air connection consisting of two perforated layers of pure aluminum and of two layers of a bonded polyester galvanized wire leads, a glass fiber insulation of 1 ½ " thick and an aluminum vapor barrier. Available Diameters : Standard Length of 25 feet Flame Speed < 25 Flame development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 4 of water Continuous maximum Negative Pressure.5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 6 inches H 2 0) -20 o F to 180 o F continuous (at 2 inches H 2 0) -20 o F to 250 o F continuous (at ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1

42 Data sheet 43 Acoustic Medical Description Flexible air connection consisting of two perforated layers of pure aluminum and of two layers of a polyester binding galvanized wire covered with a vapor barrier gray polyethylene pipe, insulated with fiberglass wool 1 ½ '' thick and covered with a polyethylene vapor barrier in gray. Available Diameters: Standard Length of 25 feet Custom length available Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 15 of water Maximum Negative Pressure.5 in. of water Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 6 inches H 2 0) -20 o F to 180 o F continuous (at 2 inches H 2 0) -20 o F to 250 o F continuous (at ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 9,5 mil. (0,21mm) Vapor barrier thickness 2mil (0.051mm) 2 mil (0.051mm) thick interior fiber barrier that keeps the fiber out of contact of the air stream. This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1

43 44 Diameter Regular 4P Vapor Barrier Gray 4PG/4PPG PRICE LIST Vapor Barrier Aluminium 4PA/4PPA P0325 4PG0325/4PPG0325 4PA0325/4PPA0325 4P0425 4PG0425/4PPG0425 4PA0425/4PPA0425 4P0525 4PG0525/4PPG0525 4PA0525/4PPA0525 4P0625 4PG0625/4PPG0625 4PA0625/4PPA0625 4P0725 4PG0725/4PPG0725 4PA0725/4PPA0725 4P0825 4PG0825/4PPG0825 4PA0825/4PPA0825 4P0925 4PG0925/4PPG0925 4PA0925/4PPA0925 4P1025 4PG1025/4PPG1025 4PA1025/4PPA1025 4P1225 4PG1225/4PPG1225 4PA1225/4PPA1225 4P1425 4PG1425/4PPG1425 4PA1425/4PPA1425 4P1625 4PG1625/4PPG1625 4PA1625/4PPA1625 4P1825 4PG1825/4PPG1825 4PA1825/4PPA1825 4P2025 4PG2025/4PPG2025 4PA2025/4PPA2025 4P2225 4PG2225/4PPG2225 4PA2225/4PPA2225 4P2425 4MPG2425/4PG2425 4PA2425/4PPA2425

44 Data sheet 45 Description Non Isolated Flexible air connection pipe consisting of a pure aluminum layer and a polyester layer binding a galvanized wire. Available diameter: 3 '- 4' - 5 '- 6' - 7 '- 8' - 9 '- 10' - 12 '- 14' - 16 '- 18' - 19 '- 20' - 22 '- 24' Length of 25 feet Custom length available Flame Speed < 25 Flame development < 50 Maximum Velocity 4000 ft/minute Continuous maximum Positive Pressure 15 in. H 2 0 (1.5 kpa) Continuous maximum Negative Pressure.5 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 6inches H 2 0) -20 o F to 180 o F continuous (à 2 inches H 2 0) -20 o F to 250 o F continuous (à ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 8,3 mil. (0,21mm) Vapor barrier thickness This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1

45 Data sheet 46 Description Thermal Flexible air connection consisting of a pure aluminum layer and a polyester layer binding a galvanized wire, a glass fiber insulation of 1 ½ " thick pipe and a Grey vapor barrier. Available Diameters : Length of 25 feet Custom length available Flame Speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/minute Periodic maximum Positive Pressure 6 in. H 2 0 (1.5 kpa) Continuous maximum Positive Pressure 6 in. H 2 0 (1.5 kpa) Maximum Negative Pressure 2 in. H 2 0 (0.13 kpa) Continuous maximum Negative Pressure 2 in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 6 inches H 2 0) -20 o F to 180 o F continuous (à 2 inches H 2 0) -20 o F to 180 o F continuous (à ½ inches H 2 0) Insulation Coefficient R 4,2-4,8 Flexible thickness 8,3 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1

46 Data sheet 47 Description Acoustic Connection of flexible air duct consists of a perforated aluminum layer and a polyester film binding a galvanized wire coated with an insulation of fiberglass 1 ½ " thick and a Grey vapor barrier. Available Diameters : Length of 25 feet Custom length available Flame speed < 25 Flame Development < 50 Maximum Velocity 4000 ft/minute Periodic maximum Positive Pressure 4 in. H 2 0 (2.5 kpa) Continuous maximum Positive Pressure 4 in. H 2 0 (1.5 kpa) Maximum Negative Pressure ½ in. H 2 0 (0.13 kpa) Continuous maximum Negative Pressure ½ in. H 2 0 (0.13 kpa) Temperature Range -20 o F to 250 o F (-30 o C à 121 o C) Maximum Temperature Use -20 o F to 140 o F continuous (at 4 inches H 2 0) -20 o F to 180 o F continuous (at 2 inches H 2 0) -20 o F to 80 o F continuous (at ½ inches H 2 0) Insulation Coefficient R 4,2-8,4 Flexible thickness 8,3 mil. (0,21mm) Vapor barrier thickness 2 mil. (0,051mm) This product meets the following standards C-UL-S-110 / UL-181 Air duct fitting class 1