Facestock physical properties. Imperial Value. MD 31,200 PSI 2,193 kg/sq cm CD 36,900 PSI 2,594 kg/sq cm. Adhesive physical properties.

Transcription

1 DURABLE PORTFOLIO Fasson 2 Mil Clear Polyester TC/S1/5#SCK Product Data Sheet Spec#: Facestock 2 Mil Clear Topcoated Polyester is a highly transparent film featuring excellent tear strength, heat resistance, dimensional stability and chemical resistance. Topcoat is designed to offer excellent printability and durability with a variety of printing processes. Adhesive S1 is a high performance, clear permanent emulsion acrylic pressure sensitive adhesive with balanced adhesion to a wide variety of substrates, including low surface energy plastics, engineering grade plastics, bare, coated, or painted metals, including powder coat and enamel paints. It features medium tack and excellent chemical and UV resistance for outdoor industrial applications. Liner 5# SCK is a bleached, super calendered paper stock with very good diecutting and matrix stripping properties. Used for standard roll-to-roll applications. Not recommended for sheeting. Facestock physical properties Caliper: ASTM D1 Tensile: ASTM D882 Adhesive physical properties Imperial Units Metric Units.2 inches 5. micron MD 31,2 PSI 2,193 kg/sq cm CD 36,9 PSI 2,594 kg/sq cm Imperial Units Metric Units Type: Emulsion Acrylic Caliper:.1 inches 25.4 microns ASTM D1 Standard Coat Wt: 27 g/sq m Minimum Appl Temp: 5 F 1 C Service Min F C Temp Range: Max F C Loop Tack 32. oz/inch 35.2 N/1 Stainless mm Steel: PSTC11 Liner physical properties Caliper: ASTM D1 Basis Wt: TAPPI T41 * (24" x 36" 5 sheets) Tensile: ASTM D882 Imperial Units Metric Units.32 inches 81.2 micron 54.5 lbs/ream 87.2 g/sq m MD 48. lbs/inch N/25 mm CD 26. lbs/inch N/25 mm Tear: MD 1.8 ounces 51.1 grams

2 Liner Release: TMLI 9 o removal of Liner from Facestock. TAPPI T414 CD 2.1 ounces 59.6 grams Total Construction Caliper (approximate): Rate of Removal Grams/2" Width 4 inches/min. 3.6 inches (6 mils; 153 microns) DURABLE PORTFOLIO Product Data Sheet Features and Benefits Crystal clear facestock with good physical strength Glossy clear top coat that accepts most flexographic, letterpress, and rotary screen inks. Excellent thermal transfer printability with some resin enhanced wax, and most resin based ribbons. Excellent chemical resistance and good outdoor durability UL and c-ul Recognized. See files MH8 and MH1725 for specific details on recognized conditions Applications and Uses Suitable for a variety of durable labeling applications such as: Product identification Barcodes WIP (Work-in-process) tracking labels Asset tags Printing and Converting The top coat is designed for printing by most solvent, UV cured, and water-based flexographic inks, UV cured letterpress and rotary screen inks. Specially formulated inks are not normally necessary, however, testing is recommended prior to final ink system selections. The following press inks have shown excellent results. Water-based flexogrphic inks: Environmental Inks & Coatings' "DR III FR"; Flint Ink's "HydroFilm ACRE"; and Water Ink Technologies' "Versifilm Plus ULF". UV Flexographic inks: Environmental Inks & Coatings' "UltraFlex III SFR"; Flint Ink's "Flexocure Sigma"; and Water Ink Technologies' "PharmaFlex UV". UL recognized with Environmental Inks and Coatings' "Aqua Plus" and "Aqua Film III" in blue and black colors, and Water Ink Technologies' "Water Gloss" ink in all colors. Also suitable for thermal transfer printing with select ribbons and printers. Consult product recognition files or the Fasson Thermal Transfer Ribbon Guide for specific recommendations. This product can be die cut and stripped at high speeds on most web-fed presses. Sample labels in a variety of shapes have been successfully dispensed and applied with standard labeling systems.

3 RoHS/Regulation 22/95/EU The substances listed in article 4 lid 1 of 22/95/EU (RoHS) are not intentionally used in this product. The concentration limits of these substances will not exceed the set maximum concentration limits as provided in the proposed amendment for 22/95/EU. Shelf Life Unless specified otherwise in this document, one year when stored at 72 F at 5% RH Note: The technical data presented is from tests we believe to be reliable but should be considered representative or typical only and should not be used for specifications purposes. This product should be tested thoroughly under end-use conditions to ensure it meets the requirements of the specific application. DURABLE PORTFOLIO Product Data Sheet Appendix Performance Data: The following technical data should be considered representative or typical only and should not be used for specification purposes. Data was generated from 2 mil polyester facestock applied to clean labatory panels. See Tech Bulletin "Achieving Maximum Adhesion" for specifics. Surface 1. Aluminum Initial (15 minute dwell) 72 Hours at Room Temperature 72 Hours at 12 F 96 Hours at F (65 C) & % Relative Humidity oz/in N/1mm oz/in N/1mm oz/in N/1mm oz/in N/1mm ABS Plastic Polypropylene HDPE LDPE Stainless Steel Environmental Performance: Chemical Resistance test results The performance results are based on 4 hour immersions at room temperature unless otherwise noted (gasoline is 1 hour). Samples were applied to stainless steel panels and conditioned for 24 hours before immersion and evaluated immediately upon removal. Adhesion measured at 1 peel.

4 Adhesion to Stainless Steel Visual Edge Chemical oz/in N/1mm Appearance Penetration mm 1. 7% IPA Tide Detergent Engine Oil (1W3) 4. Water 5. Ammonia - ph Cleaner 7. Toluene 8. Brake Fluid 9. Reference Fuel C 1. K1 Kerosene 11. Heptane Compliance Recognition: UL, C-U Underwriters Laboratories, Inc. Substrates 1. Acrylic Paint Minimum Temperature Maximum Temperature (I=Indoor Only =Indoor & Outdoor) 2. Acrylic PCP* 3. Alkyd Enamel 4. Aluminum 5. Anodized Aluminum 6. Epoxy Paint 7. Epoxy PCP* 8. Galvanized Steel 9. Polyester Paint 1. Polyester PCP*

5 11. Polyurethane PCP* 12. Blended PCP* 13. Porcelain 14. Stainless Steel 15. Melamine Phenolic Polycarbonate Thermoset Polyester ABS Plastic 2. PBT Plastic 21. Polypropylene 22. Polyphenylene Oxide 23. Polystyrene 24. Polyethylene 25. and others 26. *PCP=Powder Coat Paint Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR6", Astro Med Inc "R-5", Astro Med "RF", Astro Med "RY", Coding Prds "594", DNP "R-3", DNP "R-51", DNP "TR47", DNP "Signature Series Resin", Iimak "SP-41", Iimak "SP-33", Iimak "Primemark", Intermec "TMX ", Intermec "TMX 32", ITW "B324", Kurz "K3", Kurz "K5", Kurz "K51", NCR "Promark 3", NCR "Pacesetter", NCR "Ultra V", NCR "Perma Max", NCR "K3", Ricoh "B11C", Ricoh "B11CX", Ricoh "B11CR", Ricoh "12EC", Satorp. "Premier 1", UCA "US3", Zebra "595", Zebra "51", Zebra "5175", Zebra "5463", Zebra "Z-41", and others. Tested by Underwriters Laboratories, Inc. to meet the requirements of the Canadian Standards Association for labeling materials Substrates Minimum Temperature Maximum Temperature (I=Indoor Only

6 1. Electrostatic Paints =Indoor & Outdoor) 2. Metals 3. Plastics Group I 1 4. Plastics Group II 5. Plastics Group III 6. Plastics Group IV 7. Plastics Group V 8. Plastics Group VI 9. Plastics Group VII 1. Plastics Group VIII Recognized Ribbons: Armor "AXR7+", Armor "AXR8", Armor "AXR6", DNP "R-3", DNP "R- 51", DNP "TR47", DNP "Signature Series Resin", Kurz "K5", NCR "Promark 3", Ricoh "B11C", Ricoh "B11CR", Satorp. "Premier 1", UCA "US3", Zebra "51", and others. 49 is a registered trademark of the Clorox Company Tide is a registered trademark of the Procter & Gamble Company The information on compliance conditions, substrates, and printing products contained in the tables above represent a summary of recognized or acceptable conditions and printing products. Other conditions, substrates, and printing products may be recognized with this material. Please consult the specific compliance organization records or specific files for a complete listing. Warranty All statements, technical information and recommendations about AVERY DENNISON products are based upon tests believed to be reliable but do not constitute a guarantee or warranty. All AVERY DENNISON products are sold with the understanding that PURCHASER has independently determined suitability of such products for its purposes. AVERY DENNISON products are warranted to the original purchaser to be free from defects in material or workmanship for a period of one year from date of shipment. Purchaser's sole and exclusive remedy for breach of this warranty shall be the replacement of the defective products or, at AVERY DENNISON's option, the issuance of a credit or refund in an amount up to the purchase price of the defective product. In no event shall AVERY DENNISON be responsible for claims beyond the purchase price of the defective product. THE WARRANTY SPECIFICALLY SET FORTH ABOVE IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OR MERCHANTABILITY, FITNESS FOR ANY PARTICULAR USE AND/OR NON-INFRINGEMENT. AVERY DENNISON SPECIFICALLY DISCLAIMS AND EXCLUDES ALL OTHER SUCH WARRANTIES. IN NO EVENT SHALL AVERY DENNISON BE LIABLE TO PURCHASER OR ANY OTHER PARTY FOR INDIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL OR PUNITIVE DAMAGES. No representative or agent of AVERY DENNISON is authorized to give any guarantee or warranty or make any representation contrary to the above. No waiver, alteration, addition or modification of the foregoing conditions shall be valid unless made in writing and signed by an executive officer of AVERY DENNISON.

7 Avery Dennison Fasson Roll North America Norton Parkway Mentor, OH (US & Canada) (Mexico)